Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
TECHNICAL DATA
Typical Properties of Ultra Plus
Synthetic Compressor Lubricant
Property Test Method Performance
SAE Viscosity Classification J300 SAE10/20
ISO Viscosity Classification ASTM D2422 32
Viscosity Index D2270 150
Viscosity, cSt (SUS)
at 40C D445 34.9
at 100C D445 6.65
at 0F D445 1100
at -40C D445 13,800
Pour Point, F (C) D97 -59 (-51)
Flash Point, F (C) D92 263 (128)
Auto Ignition Temperature, F (C) E659 424 (218)
Conradson Carbon Residue, % D189 <0.1
Copper Strip Corrosion, 3 hrs @ 212F/100C D130 1a
4-Ball Wear, 40kg, 1 hr, 1800 rpm, (mm) D2266 0.73
Weld Point, kg D2783 100
Evaporation Loss 6.5 hrs @ 400F D972 4.13
Specific Gravity @15.6C D1298 0.9752
Ferrous Metal Corrosion (Rust Test)
Distilled Water D665A pass
Synthetic Sea Water D665B pass
Foam Tendency (Sequence I, II, III)
Sequence I D892 Nil
Sequence II D892 11.5 ml
Sequence III D892 Nil
Total Acid Number D664 0.19
High Pressure Oxidation Test (hr) D2272 18.5
Specific Heat, cal/gm/C
at 185F (btu/lb mol F) D2766 0.47
Thermal Conductivity, cal/(cm)(sec)(C)
at 150F D2717 36.4x10 -5
at 200F D2717 34.6x10-5
at 250F D2717 33.7x10-5
Demulsibility @ 130F (54C) ml oil/emulsion (min) D1401 41-39-0 (35)
Technical Data
TOXICITY: NOT RECOMMENDED:
Please refer to the Material Safety Data Sheet Seals: Neoprene, Natural Rubber, SBR,
for Ultra Plus (Form APDD-772). Buna-S, Butyl Rubber,
Chlorosulfonated polyethylene,
COMPATIBILITY: Low Nitrile Buna-N
The following lists serve as a guide for the Plastics: Polystyrene, PVC, ABS
material compatibility of various seals,
Paints: Acrylic, Latex (household), Vinyl,
plastics, and paints with Ultra Plus*.
Varnish, Lacquer
ACCEPTABLE:
*Under normal circumstances. In extreme
Seals: Fluorocarbon (Viton), High Nitrile
conditions, such as high temperatures
Buna-N, Florosilicone Rubber,
(over 250F) and/or high stress, compatibility
Polysulfide, Hytrel, Kalrez, CPM
should be re-evaluated.
Plastics: Nylon, Teflon, Deltrin, Celcon,
PBT, HD-PPE, Ryton (oil-less) Note: In the case of employment of new seal
Paints: Epoxy, Baked Phenolic, 2-Comp composition, lubricant compatibility should be
Urethane, MC-Urethane, evaluated. Please refer to Ingersoll-Rand
Oil-Resistant Alkyd Contract Service, Davidson, North Carolina.
APPLICATION DEPENDENT:
Seals: Med Nitrile Buna-N, Polyurethane,
EPDM, Epichlorohydrin, Polyacrylate
Rubber, Silicone Rubber
Plastics: Polyurethane, Polyethylene, Noryl,
Lexan, Lucite, Polysulfone,
Polycarbonate (type)
Paints: Alkyds, Phenolic, SC-Urethane,
Industrial Latex
Ingersoll-Rand Company
Air Solutions Group
800-C Beaty Street
Davidson, NC 28036