Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
chassis PL14.12
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
140324
1-1 PL14.12SP
Downloaded from www.Manualslib.com manuals search engine
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV d. Leakage Current Hot Check - With the
instrument completely reassembled, plug the
Circuit AC line cord directly into a 120 V AC outlet. (Do
1. Before returning an instrument to the not use an isolation transformer during this
customer, always make a safety check of the test.) Use a leakage current tester or a
entire instrument, including, but not limited to, the metering system that complies with American
following items: National Standards Institute (ANSI) C101.1
a. Be sure that no built-in protective devices are Leakage Current for Appliances and
defective and have been defeated during Underwriters Laboratories (UL) 1410, (50.7).
servicing. (1) Protective shields are provided With the instrument AC switch first in the on
on this chassis to protect both the technician position and then in the off position, measure
and the customer. Correctly replace all missing from a known earth ground (metal water pipe,
protective shields, including any removed for conduit, etc.) to all exposed metal parts of the
servicing convenience. (2) When reinstalling instrument (antennas, handle brackets, metal
the chassis and/or other assembly in the cabinet, screw heads, metallic overlays, control
cabinet, be sure to put back in place all shafts, etc.), especially any exposed metal
protective devices, including but not limited to, parts that offer an electrical return path to the
nonmetallic control knobs, insulating chassis. Any current measured must not
fishpapers, adjustment and compartment exceed 0.5 milli-ampere. Reverse the
covers/shields, and isolation resistor/capacitor instrument power cord plug in the outlet and
networks. Do not operate this instrument or repeat the test.
permit it to be operated without all
protective devices correctly installed and READING SHOULD
functioning. Servicers who defeat safety NOT BE ABOVE 0.5 mA
features or fail to perform safety checks
may be liable for any resulting damage. LEAKAGE
DEVICE CURRENT
b. Be sure that there are no cabinet openings BEING TESTER
through which an adult or child might be able to TESTED + _
insert their fingers and contact a hazardous TEST ALL EXPOSED
voltage. Such openings include, but are not METAL SURFACES
limited to, (1) spacing between the Liquid
Crystal Panel and the cabinet mask, (2)
excessively wide cabinet ventilation slots, and
(3) an improperly fitted and/or incorrectly ALSO TEST WITH
secured cabinet back cover. PLUG REVERSED
c. Antenna Cold Check - With the instrument AC USING AC
plug removed from any AC source, connect an ADAPTER PLUG EARTH
electrical jumper across the two AC plug AS REQUIRED GROUND
prongs. Place the instrument AC switch in the
on position. Connect one lead of an ohmmeter
to the AC plug prongs tied together and touch ANY MEASUREMENTS NOT WITHIN THE
the other ohmmeter lead in turn to each tuner LIMITS SPECIFIED HEREIN INDICATE A
antenna input exposed terminal screw and, if POTENTIAL SHOCK HAZARD THAT MUST
applicable, to the coaxial connector. If the BE ELIMINATED BEFORE RETURNING THE
measured resistance is less than 1.0 megohm INSTRUMENT TO THE CUSTOMER OR
or greater than 5.2 megohm, an abnormality BEFORE CONNECTING THE ANTENNA OR
exists that must be corrected before the ACCESSORIES.
instrument is returned to the customer. Repeat
2. Read and comply with all caution and safety-
this test with the instrument AC switch in the off
related notes on or inside the receiver cabinet, on
position.
the receiver chassis, or on the Liquid Crystal
Panel.
2-1 LTVN_ISP
Downloaded from www.Manualslib.com manuals search engine
3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and
to the mechanical or electrical design of this TV mechanical parts have special safety-related
receiver. Design alterations and additions, characteristics which are often not evident from
including, but not limited to circuit modifications visual inspection, nor can the protection they give
and the addition of items such as auxiliary audio necessarily be obtained by replacing them with
and/or video output connections, might alter the components rated for higher voltage, wattage, etc.
safety characteristics of this receiver and create a Parts that have special safety characteristics are
hazard to the user. Any design alterations or identified by a # on schematics and in parts lists.
additions will void the manufacturer's warranty and Use of a substitute replacement that does not
may make you, the servicer, responsible for have the same safety characteristics as the
personal injury or property damage resulting recommended replacement part might create
therefrom. shock, fire, and/or other hazards. The product's
4. Hot Chassis Warning - safety is under review continuously and new
instructions are issued whenever appropriate.
a. Some TV receiver chassis are electrically
Prior to shipment from the factory, our products
connected directly to one conductor of the AC
are strictly inspected to confirm they comply with
power cord and maybe safety-serviced without
the recognized product safety and electrical codes
an isolation transformer only if the AC power
of the countries in which they are to be sold.
plug is inserted so that the chassis is
However, in order to maintain such compliance, it
connected to the ground side of the AC power
is equally important to implement the following
source. To confirm that the AC power plug is
precautions when a set is being serviced.
inserted correctly, with an AC voltmeter,
measure between the chassis and a known
earth ground. If a voltage reading in excess of
1.0 V is obtained, remove and reinsert the AC
power plug in the opposite polarity and again
measure the voltage potential between the
chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground
regardless of the AC plug polarity. This chassis
can be safety-serviced only with an isolation
transformer inserted in the power line between
the receiver and the AC power source, for both
personnel and test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulation material that must not be defeated or
altered.
5. Observe original lead dress. Take extra care to
assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch
thermally hot parts, c. the AC supply, d. high
voltage, and, e. antenna wiring. Always inspect in
all areas for pinched, out of place, or frayed wiring.
Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
2-2 LTVN_ISP
Downloaded from www.Manualslib.com manuals search engine
Precautions during Servicing
A. Parts identified by the # symbol are critical for
safety.
Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.
F. Observe that the wires do not contact heat
producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
11~13 lb (5~6 kg) of force in any direction will not
loosen it.
I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal
connectors, first, disconnect the AC plug from the
AC supply outlet.
L. When installing parts or assembling the cabinet
parts, be sure to use the proper screws and
tighten certainly.
2-3 LTVN_ISP
Downloaded from www.Manualslib.com manuals search engine
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and
wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified
values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between
soldered terminals, and between terminals and Chassis or Secondary Conductor
surrounding metallic parts. (See Fig. 1)
Primary Circuit
Table 1: Ratings for selected area
Clearance d' d
AC Line Voltage Region
Distance (d), (d)
U.S.A. or 3.2 mm
110 to 130 V
Canada (0.126 inches)
Fig. 1
Fig. 2
AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:
U.S.A. or 0.15 F CAP. & 1.5 k Exposed accessible
110 to 130 V i 0.5 mA rms
Canada RES. Connected in parallel parts
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2-4 LTVN_ISP
Downloaded from www.Manualslib.com manuals search engine
STANDARD NOTES FOR SERVICING
Circuit Board Indications How to Remove / Install Flat Pack-IC
1. The output pin of the 3 pin Regulator ICs is
1. Removal
indicated as shown.
With Hot-Air Flat Pack-IC Desoldering Machine:
Top View Bottom View 1. Prepare the hot-air flat pack-IC desoldering
Input machine, then apply hot air to the Flat Pack-IC
Out In (about 5 to 6 seconds). (Fig. S-1-1)
Pin 1
10
3-1 TVN_SN
Downloaded from www.Manualslib.com manuals search engine
3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron:
be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from
pin or the solder lands under the IC when all pins of the flat pack-IC. When you use solder
removing it. flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
Hot-air
Flat Pack-IC Flat Pack-IC Desoldering Braid
Desoldering
Machine
CBA
Soldering Iron
Masking Flat Pack-IC Fig. S-1-3
Tape
Tweezers 2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
Fig. S-1-2
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)
Sharp
Pin
Fine Tip
Soldering Iron
Fig. S-1-4
3-2 TVN_SN
Downloaded from www.Manualslib.com manuals search engine
With Iron Wire: 2. Installation
1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA
flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more
you can remove it easily. (Fig. S-1-3) easily.
2. Affix the wire to a workbench or solid mounting 2. The I mark on the flat pack-IC indicates pin 1.
point, as shown in Fig. S-1-5. (See Fig. S-1-7.) Be sure this mark matches the
3. While heating the pins using a fine tip soldering pin 1 on the PCB when positioning for installation.
iron or hot air blower, pull up the wire as the solder Then presolder the four corners of the flat pack-IC.
melts so as to lift the IC leads from the CBA (See Fig. S-1-8.)
contact pads as shown in Fig. S-1-5. 3. Solder all pins of the flat pack-IC. Be sure that
4. Bottom of the flat pack-IC is fixed with glue to the none of the pins have solder bridges.
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6) Example :
5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Hot Air Blower Fig. S-1-7
or
Presolder
Iron Wire
Soldering Iron
To Solid
Mounting Point
Fig. S-1-5
Flat Pack-IC
CBA
Flat Pack-IC
Tweezers
Fig. S-1-6
3-3 TVN_SN
Downloaded from www.Manualslib.com manuals search engine
Instructions for Handling Semi-
conductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
<Incorrect>
CBA
1M
CBA
1M
Conductive Sheet or
Copper Plate
3-4 TVN_SN
Downloaded from www.Manualslib.com manuals search engine
CABINET DISASSEMBLY INSTRUCTIONS
Screw Torque Specification Step/
Fig.
Loc. Part Removal Note
Ref. Part Tightening No.
No. Number Part Name Torque No.
SCREW BIND BLACK_NI 4(S-5), CN3105,
L9 GBHP3120
+P-TITE M3X12.0
5.20.9lbin Digital Main D2
[4] CN3801, CN3904, ---
CBA Unit D5
SCREW BIND 3CHROM Jack Holder
L23 GBJS3060 4.30.9lbin
+S-TITE M3X6.0
[5] Speaker D3 ---------------- ---
SCREW BIND BLACK_NI
L27 GBHS3080 5.20.9lbin
+S-TITE M3X8.0 Stand
[6] D3 2(S-6) ---
STAND SCREW KIT Holder
SSK1 1ESA34003 (SCREW BIND BLACK_NI
+P-TITE M4X25.0) CN4051, Function
(approx. Function D3
8.70.9lbin)* [7] Knob, Knob Frame, 2
STAND SCREW KIT CBA Unit D5
SSK1 1ESA34004 (SCREW BIND BLACK_NI
Hook
+P-TITE M4X14.0) IR Sensor D3
[8] Sensor Shield, Hook 2
CBA Unit D5
* For reference
Decoration Plate, LED
LCD Panel
1. Disassembly Flowchart [9]
Assembly
D4 Lens, Leading Edge 1
Cover, Hook
This flowchart indicates the disassembly steps for the
cabinet parts and the CBA in order to gain access
to items to be serviced. When reassembling, follow (1) (2) (3) (4) (5)
the steps in reverse order. Bend, route and dress *1: 32PFL4909/F7, 32PFL4909/F8
the cables as they were.
*2: 32PFL4609/F7
[1] Stand Base [1] Stand
Assembly*2 Assembly*1
Note:
(1) Order of steps in procedure. When reassembling,
[3] Power Supply
[2] Rear Cabinet
[4] Digital Main follow the steps in reverse order. These numbers
CBA CBA Unit are also used as the Identification (location) No. of
parts in figures.
[7] Function
[5] Speaker [6] Stand Holder (2) Parts to be removed or installed.
CBA Unit
(3) Fig. No. showing procedure of part location
[8] IR Sensor
CBA Unit (4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
[9] LCD Panel desoldered.
Assembly P = Spring, L = Locking Tab, S = Screw,
H = Hex Screw, CN = Connector
2. Disassembly Method e.g. 2(S-2) = two Screws of (S-2),
2(L-2) = two Locking Tabs of (L-2)
Step/ (5) Refer to the following Reference Notes in the
Fig.
Loc. Part Removal Note Table.
No.
No.
Stand Base
[1]*1 D1 3(S-1), Stand Neck ---
Assembly
Stand
[1]*2 D1 3(S-1) ---
Assembly
Rear
[2] D1 11(S-2), 7(S-3) ---
Cabinet
Power
D2 4(S-4), CN501,
[3] Supply ---
D5 CN601, CN1001
CBA
4-1 PL14.12-A_DC
Downloaded from www.Manualslib.com manuals search engine
Important precautions concerning the 2. When you disassemble/re-assemble the
LCD Panel Assembly: Function CBA Unit or the IR Sensor CBA Unit
1. When you disassemble/re-assemble the LCD Be careful not to break the hooks. If you pull with too
Panel Assembly much force, the hooks may be damaged.
Do not pull the FFC Cable and Board Cable Make sure the hooks are securely in place when
forcefully when you re-assemble. assembling.
Be careful not to scratch the display panel when The Function CBA Unit, Function Knob and Knob
assembling. Frame are fixed in place by the hooks. Make sure
these hooks are not damaged. Make sure the
Make sure to replace the Decoration Plate, LED
Function CBA Unit, Function Knob and Knob Frame
Lens and Leading Edge Cover to a new one when
are securely in place when re-assembling.
replacing the LCD Panel Assembly.
The IR Sensor CBA Unit and Sensor Shield are
fixed in place by the hooks. Make sure these hooks
are not damaged. Make sure the IR Sensor CBA
Unit and Sensor Shield are securely in place when
re-assembling.
(S-2)
(S-2)
(S-3)
(S-2)
32PFL4609/F7 32PFL4909/F7,
(S-3)
32PFL4909/F8
4-2 PL14.12-A_DC
Downloaded from www.Manualslib.com manuals search engine
Jack Holder
(S-5)
(S-4)
Fig. D2
4-3 PL14.12-A_DC
Downloaded from www.Manualslib.com manuals search engine
[6] Stand Holder
Hook*2
B3
[5] Speaker
(S-6)
Function Knob*2
Knob Frame*2
Fig. D3
*2: Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the
Function CBA Unit or IR Sensor CBA Unit.
4-4 PL14.12-A_DC
Downloaded from www.Manualslib.com manuals search engine
[9] LCD Panel Assembly*1
Decoration Plate*1
LED Lens*1
Hook*1
Leading Edge Cover*1
Fig. D4
* 1: Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the LCD
Panel Assembly.
4-5 PL14.12-A_DC
Downloaded from www.Manualslib.com manuals search engine
TV Cable Wiring Diagram
CN3904
CN501
CN3601
Function
CN601
CBA Unit
CN3105 CN3801
To AC Cord
To Speaker
CN4051
IR Sensor CBA Unit
CN4052
CN4001
Fig. D5
4-6 PL14.12-A_DC
Downloaded from www.Manualslib.com manuals search engine
ELECTRICAL ADJUSTMENT INSTRUCTIONS
General Note: CBA is abbreviation for 1. Purity Check Mode
Circuit Board Assembly.
This mode cycles through full-screen displays of red,
Note: Electrical adjustments are required after green, blue, and white to check for non-active pixels.
replacing circuit components and certain
1. Enter the service mode.
mechanical parts. It is important to perform
these adjustments only after all repairs and 2. Each time the [7] button on the remote control unit
replacements have been completed. is pressed, the display changes as follows.
Also, do not attempt these adjustments unless
the proper equipment is available. Purity Check Mode
White mode
Test Equipment Required
1. Remote control unit [7] button
2. Color Analyzer,
CA-310 (KONICA MINOLTA Luminance meter) or
measuring instrument as good as CA-310.
[7] button
Black mode
How to set up the service mode:
Service mode:
1. Turn the power on.
2. Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on [7] button
the remote control unit in this order. The following White 50% mode
screen appears.
[current]
File code: ***-****_***_*
Total checksum: Push "0" key [7] button
Panel-Option code: **-***-***-***-***-***
Red, Green, Blue mode
***-***-***-***-***
Press "POWER" key to exit.
MAC address: **:**:**:**:**:**
ESN: *****************************
Flicker: *****
Tuner: ****
HDMI UART: OFF Total Watch Time: ***** [7] button
Touch Sensor Ver: ------ / -.--.-- System Time: **:**
EDID: Push "0" key Lightsensor: V-ramp mode
**
[7] button
White 20% mode
Note:
When entering this mode, the default setting is White mode.
5-1 PL14.12EA
Downloaded from www.Manualslib.com manuals search engine
The VCOM Adjustment should be The White Balance Adjustment should be
performed when replacing the Digital performed when replacing the LCD Panel
Main CBA. or Digital Main CBA.
2. VCOM Adjustment 3. White Balance Adjustment
Test Point Adj. Point Purpose: To mix red and blue beams correctly for
[CHANNEL UP/DOWN] pure white.
Screen
buttons Symptom of Misadjustment: White becomes bluish
M. EQ. Spec. or reddish.
Color analyzer See below
ITEM SPECIFICATION
Figure
x= 0.272 0.003
Color temperature
y= 0.278 0.003
To avoid interference from ambient
light, this adjustment should be Internal pattern
performed in a dark room. Input Signal
(30/50/80% raster)
Perpendicularity Measurement point Screen center
CA-310 (KONICA MINOLTA
Luminance meter) or
M. EQ.
measuring instrument as
good as CA-310.
60min.
Aging time (Retail MODE/100IRE Raster
Color Analyzer HDMI 1080i@60)
Shipment setting/
MODE setting of TV
Retail MODE
1. Set the color analyzer at the zero point calibration
and bring the optical receptor pointing at the Ambient
25C 5C
center of the LCD-Panel. temperature
Note: The optical receptor must be set
1. Operate the unit for more than 30 minutes.
perpendicular to the LCD Panel surface.
2. Turn the power on. 2. Enter the service mode.
Note: Execute the VCOM adjustment within 2 3. Press [VOLUME DOWN] button three times on the
minutes after you turn the power on. remote control unit to select Drive setting mode.
3. Enter the service mode. Drive- appears in the screen.
4. Press [2] button two times on the remote control 4. Set the color analyzer at the CHROMA mode and
unit to select VCOM2(AUTO) adjustment mode. zero point calibration. Bring the optical receptor
5. Press [CHANNEL UP/DOWN] buttons on the pointing at the center of the LCD-Panel.
remote control unit so that the color analyzer value
To avoid interference from ambient
becomes minimum. light, this adjustment should be
6. To cancel or to exit from the VCOM Adjustment, performed in a dark room.
press [CH RETURN] or [PREV CH] button.
Perpendicularity
Color Analyzer
Note: The optical receptor must be set
perpendicularly to the LCD Panel surface.
5-2 PL14.12EA
Downloaded from www.Manualslib.com manuals search engine
5. Press [3] button to select the HDB for High Drive 13. Press [9] button to select the LDB for Low Drive
Blue adjustment. (HDB appears in the screen.) Blue adjustment (LDB appears in the screen.)
6. Press [MENU] button. The internal Raster signal and press [CHANNEL UP/DOWN] buttons to
appears in the screen. (Internal (Single) appears adjust the color temperature.
in the upper right of the screen as shown below.)
Internal (Single)
Internal (Single)
LDB 0
HDB 0
14. Press [7] button to select the LDR for Low Drive
7. Press [CHANNEL UP/DOWN] buttons to adjust Red adjustment (LDR appears in the screen.)
the color temperature becomes 12000K and press [CHANNEL UP/DOWN] buttons to
(x= 0.272 / y= 0.278 0.003). adjust the color temperature.
8. Press [1] button to select the HDR for High Drive 15. If necessary, adjust the LDB or LDR again.
Red adjustment (HDR appears in the screen.) 16. Press [VOLUME DOWN] button to shift to the
and press [CHANNEL UP/DOWN] buttons to Debugging Message mode.
adjust the color temperature. If there is no message under [WB] section, this
9. If necessary, adjust the HDB or HDR again adjustment completes.
If Drive settings are NG. Retry again. is
10. Press [6] button to select the MDB for Middle
displayed, repeat above steps from 5. to 15. Then
Drive Blue adjustment (MDB appears in the
check Debugging Message again. If Drive
screen.) and press [CHANNEL UP/DOWN]
settings are NG. Retry again. is displayed, replace
buttons to adjust the color temperature.
the LCD Panel or Digital Main CBA.
17. To cancel or to exit from the White Balance
Internal (Single) Adjustment, press [CH RETURN] or [PREV CH]
button.
MDB 0
5-3 PL14.12EA
Downloaded from www.Manualslib.com manuals search engine
HOW TO INITIALIZE THE LCD TV
The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to
select a language and program channels after the set has been initialized.
To put the program back at the factory-default, initialize the LCD TV using the following procedure.
6-1 PL14.12INT
Downloaded from www.Manualslib.com manuals search engine
FIRMWARE RENEWAL MODE
Equipment Required Update file selection screen appears as follows.
(Files included in the USB storage device are
a. USB storage device
displayed.)
b. Remote Control Unit
"*" differs depending on the models.
Firmware Update Procedure
Select an upgrade file *****_******.upg
1. Turn the power off and unplug the AC Cord.
*****_******.upg
2. Insert the USB storage device to the USB port as
*****_******.upg
shown below.
Rear Cabinet
(example)
USB port
Cancel
1 23
Note:
USB storage To cancel the update mode, select Cancel and
device
press the [OK] button.
10. Select the file and press [OK] button.
11. The update will start and the following will appear
in the screen.
"*" differs depending on the models.
Current Version: ***-****-***-*
New Version: ***-****-***-*
3. Plug the AC Cord and turn the power on. Are you sure you want to update?
4. After few seconds, the menu mode will appear in
the screen.
Note:
After 30 seconds without an operation, the menu No Yes
mode will disappear automatically.
To display the menu mode again, press the
[MENU] button on the remote control unit. Note:
5. Select Setup and press the [OK] button to display If the above screen isnt displayed, repeat from
the setup menu. step 1.
12. Select Yes and press the [OK] button to update.
6. Select Software.
Note:
7. Select Software update.
Do not remove the USB storage device or turn the
8. Select USB. TV off while update is in progress.
9. Press the [OK] button on the remote control unit to 13. When the firmware update is completed, the
enter the update mode. following will appear in the screen.
7-1 PL14.12FW
Downloaded from www.Manualslib.com manuals search engine
TROUBLESHOOTING
[Power Supply Section]
FLOW CHART NO.1
The power cannot be turned on.
No
Is the fuse (F602) normal? See FLOW CHART No.2 <The fuse blows out.>
Yes
Is normal state restored when once unplugged No Check if there is any leak or short-circuit on the
power cord is plugged again after several seconds? primary circuit component and repair it if defective.
Yes (C607, D601, D602, D603, D604, D605, D607, D608,
No D609, D621, D623, Q601, Q602,
Is the P-ON+21V line voltage normal? Q621, R602, R611, T601)
Yes
Check if there is any leak or short-circuit on the Check if there is any leak or short-circuit on the
primary circuit component and repair it if defective. each rectifying circuit component of secondary side
and repair it if defective.
Make sure to repair the primary circuit component before replacing the fuse (F602).
Does the photocoupler circuit on the secondary side No Check IC602, D660, D661, Q653 and their periphery
operate normally? circuit. Repair it if defective.
Yes
Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side.
Repair it if defective. (D650, D651, D653, D655, Q656, Q658)
8-1 PL14.12ATR
Downloaded from www.Manualslib.com manuals search engine
FLOW CHART NO.5
P-ON+21V is not output.
Is approximately +21V voltage supplied to the cathode No Check D650, D651, D652, C651, C652, C653, and
of D650(D651)? their periphery circuit. Repair it if defective.
Yes
Check if there is any leak or short-circuit on the load
circuit. Repair it if defective.
No
Is approximately +13V voltage supplied to the cathode Check D653, D654, D655, C654, C655 and their
of D653(D655)? periphery circuit. Repair it if defective.
Yes
No
Is approximately +13V voltage supplied to the emitter Check D653, D654, D655, C654, C655 and their
of Q658? periphery circuit. Repair it if defective.
Yes
No
Is approximately +12V voltage supplied to the base of Check D662, Q656 and their periphery circuit.
Q658? Repair it if defective.
Yes
Replace Q658.
8-2 PL14.12ATR
Downloaded from www.Manualslib.com manuals search engine
[Video Signal Section]
FLOW CHART NO.1
The key operation is not functioning.
No
When pressing each buttons, does the Pin(6) voltage Replace the Function CBA Unit.
of CN4052 decrease?
Yes
No
Is approximately +3.3V voltage supplied to Pin(1) of Check AL+3.3V line and repair it if defective.
CN4052?
Yes
No
Is the "L" pulse supplied to Pin(5) of CN4052 when the Replace the Function CBA Unit.
infrared remote control activated?
Yes
Replace the Digital Main CBA Unit.
No
Is approximately +21V voltage supplied to See FLOW CHART NO.5 <P-ON+21V is not output.
Pin(1, 2, 3, 4) of CN501? [Power Supply Section]>
Yes
No
Is approximately +3.3V voltage supplied to Pin(16) of See FLOW CHART NO.7 <AL+3.3V is not output.
CN501? [Power Supply Section]>
Yes
Digital Main CBA Unit or LCD Panel Assembly may
be defective. Check and replace these parts.
8-3 PL14.12ATR
Downloaded from www.Manualslib.com manuals search engine
[Audio Signal Section]
FLOW CHART NO.1
Audio is not output normally.
No
Is approximately +13V voltage supplied to Pin(6, 7, 8, 9) See FLOW CHART NO.6 <AMP+13V is not output.
of CN501? [Power Supply Section]>
Yes
No
Is approximately +3.3V voltage supplied to Pin(16) of See FLOW CHART NO.7 <AL+3.3V is not output.
CN501? [Power Supply Section]>
Yes
No
Are the audio signals output to Pin(1, 2, 3, 4) of CN3801? Replace the Digital Main CBA Unit.
Yes
8-4 PL14.12ATR
Downloaded from www.Manualslib.com manuals search engine
IC3101
(MAIN MICRO CONTROLLER)
CN3706
TX(+)
AD6 TX(+)
TX(-)
ETHERNET AE6 TX(-)
JACK RX(+) RS4051
AC7 RX(+)
RX(-) REMOTE
AC8 RX(-)
SENSOR
VGA-SCL
Y7 VGA-SCL
1. System Control Block Diagram
VGA-SDA
AD3 VGA-SDA
TO VIDEO/AUDIO LCD-P-ON
W2 LCD-P-ON
BLOCK DIAGRAM
9-1
COMP-DET
H6 COMP-DET
HP-DET
L2 HP-DET
PROTECT3
PROTECT3 T2 3 PROTECT3 21 TO
BACKLIGHT-SW
BACKLIGHT-SW W3 5 BACKLIGHT-SW 19 LED BACKLIGHT DRIVE
BACKLIGHT-ADJ BLOCK DIAGRAM
BACKLIGHT-ADJ P7 7 BACKLIGHT-ADJ 17
X3101
25MHz AE4 AXI
OSC AD4 AXO
PL14.12BLS
VIDEO SIGNAL AUDIO SIGNAL
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
2. Video/Audio Block Diagram
TO DIGITAL
SIGNAL PROCESS
JK3706 BLOCK DIAGRAM
AUDIO(L)-IN
AUDIO(L)-IN AUDIO(R)-IN
9-2
AUDIO(R)-IN
Q3709
SPDIF
DIGITAL BUFFER
AUDIO-OUT
(COAXIAL)
HP(R)
JK3801 HP(L)
HEADPHONE
JACK
25 DRIVE AMP(L)-OUT
PWM POWER 3
LOGIC LIMIT
CN3801 23 DRIVE
SP3801 SP(L)+ 1
SPEAKER SP(L)- 2
L-CH 18 DRIVE AMP(R)-OUT
PWM POWER 12
SP(R)+ 4 LIMIT
LOGIC
SP(R)- 3 20 DRIVE VGA-SCL
Q3821
VGA-SDA
1 P-ON+3.3V
CONTROL LOGIC LCD-P-ON TO SYSTEM CONTROL
2
SP3802 COMP-DET BLOCK DIAGRAM
SPEAKER HP-DET
R-CH Q3822
PL14.12BLVA
LCD PANEL
VIDEO SIGNAL AUDIO SIGNAL ASSEMBLY
9-3
10 AD22
CLOCK(-)
12 AC22
HDMI-DATA
16 W6 IC3401
HDMI-CLOCK
15 T7 (DDR3 SDRAM)
3. Digital Signal Process Block Diagram
MMDQ(0-31)
JK3715 DATA(0-15)
DATA0(+) HDMI
7 W23 I/F ADDESS(0-14)
DATA0(-) MMA(0-14)
9 W22 IC3402
DATA1(+)
4 V23 HDMI SW (DDR3 SDRAM)
DATA1(-)
6 V22 DATA(16-31)
DATA2(+)
1 U23
HDMI-IN2 DATA2(-) ADDESS(0-14)
3 V24
CLOCK(+)
10 Y25
CLOCK(-) IC3102
12 Y24
HDMI-DATA (NAND FLASH MEMORY)
16 AA5
HDMI-CLOCK MMCDAT(0-7)
15 V7 VIDEO DATA(0-7)
DECODER
JK3716
DATA0(+)
7 AB24
DATA0(-)
9 AC25
DATA1(+)
4 AA23
DATA1(-)
6 AB25
DATA2(+)
1 Y23
HDMI-IN3 DATA2(-)
3 AA24
CLOCK(+)
10 AC24
CLOCK(-)
12 AD25
HDMI-DATA
16 AE3
HDMI-CLOCK
15 R9
DIGITAL MAIN CBA UNIT
PL14.12BLD
LCD PANEL
ASSEMBLY
P-ON+21V
OVP 3
DRIVE 14 Q1001
CN1001
15 2 VLED1
CONTROL 1 ILED1
PROTECT3 LOGIC
TO
SYSTEM CONTROL BACKLIGHT-SW
2 VREG
BLOCK DIAGRAM BACKLIGHT-ADJ
6 DRIVE 13 Q1002
9-4
11
4. LED Backlight Drive Block Diagram
PL14.12BLBD
CAUTION !
NOTE:
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, The voltage for parts in hot circuit is measured using
If Main Fuse (F602) is blown , check to see that all components in the power supply replace only with same type 2.5A, 250V fuse. hot GND as a common terminal.
circuit are not defective before you connect the AC plug to the AC power supply. 2.5A 250V ATTENTION : Utiliser un fusible de rechange de mme type de 2.5A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
AC601
AC CORD F602 L601 D601- D604 T601
CN601 2.5A/250V CN501 CN3601
B LINE BRIDGE 6 7 6-9 AMP+13V 15-18 AMP+13V
W FILTER RECTIFIER 16 AL+3.3V 8 AL+3.3V
1-4 P-ON+21V 20-23 P-ON+21V
4 10
Q656, Q658
Q601 +3.3V REG.
SWITCHING 2
11
5. Power Supply Block Diagram
AMP+13V
1 12 P-ON+21V
9-5
Q621
OVER
VOLTAGE
PROTECT
RESET TO
P-ON-H2 SYSTEM CONTROL
IC602 BLOCKDIAGRAM
ERROR
VOLTAGE DET
4 1
Q602
SWITCHING
3 2
CONTROL
Q653
HOT COLD
POWER SUPPLY CBA
PL14.12BLP
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark # in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.
Notes:
1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.
2. All resistance values are indicated in ohms
(K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.
4. All capacitance values are indicated in F
(P = 10-6 F).
5. All voltages are DC voltages unless otherwise
specified.
6. This schematic diagrams are masterized version
that should cover the entire PL14.12 chassis
models.
Thus some parts in detail illustrated on this
schematic diagrams may vary depend on the
model within the PL14.12 chassis.
Please refer to the parts lists for each models.
7. The Circuit Board layout illustrated on this service
manual is the latest version for this chassis at the
moment of making this service manual.
Depend on the mass production date of each
model, the actual layout of each Board may differ
slightly from this version.
10-1 FL14.12SC
Downloaded from www.Manualslib.com manuals search engine
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F602) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.
3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
1 2 3
(Unit: Volt) 5.0 5.0 Power on mode
10-2 FL14.12SC
Downloaded from www.Manualslib.com manuals search engine
Power Supply Schematic Diagram
CAUTION ! NOTE:
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, The voltage for parts in hot circuit is measured using
If Main Fuse (F602) is blown , check to see that all components in the power supply replace only with same type 2.5A, 250V fuse. hot GND as a common terminal.
circuit are not defective before you connect the AC plug to the AC power supply. 2.5A 250V ATTENTION : Utiliser un fusible de rechange de mme type de 2.5A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
TO LCD PANEL
C1014 C1015 C1016 C1017 C1018 C1021 D1001A L1002 L1003 D1002
1/100V 1/100V OPEN 47/100V 47/100V 47/100V SK210TD OPEN BEAD OPEN
D1004 C1019 20.3 D Q1001
MM5Z30B R1025 OPEN AP18T10AGH-HF R1013
360K G (SWITCHING) 10
R1023 5.9
10K R1026 0.1 S C1008
2.5A250V 240K R1018 560P
L601 C603 200
F602 LINE 1000P/250V IC1001 R1016
2.5A/250V FILTER R1024 R1027 BD9486F-GE2 C1009 R1015
10K 22K 1000P 0.12/1W OPEN
LED BACKLIGHT R1017
AC601 R1014 DRIVER OPEN
AC CORD CN601 D602 D603 C602 0
1000P/250V 5.0 1
B R601 SA601
C604
0.22
C614
0.22
1N5397BD 1N5397BD VCC 16 11.7
1.2M VARISTOR D1003 C1005
W /1/2W /275V /275V 1SS400ST 1 3.0 2 VREG 15 0.1
D601 D604 C616 1.9 3
1N5397BD 1N5397BD 1000P/250V OVP DRIVE 14 5.9 D 0.8 Q1002
R1001 R1010 R1028
22K 36K 3.5 4 1K G AP18T10AGH-HF
UVLO DRIVE 13 9.6 (SWITCHING)
R1002 R1003 C1004 C1006 10.2 S
OPEN 0.22 5.1 5
9.1K 9.1K SS GND 12 0 0.8 GP001
OPEN
C617 R1021
3 10/16V
C618
10/16V
R602 JS603
2.7/5W OPEN
JS604
OPEN C1025 R1009
OPEN 100K
2.5 6
0 7 CP
CONTROL
LOGIC 11 0.6
10 2.1
R1020 C1010
120 0.22
C1011
C1013
2200P
51
R1029
0.75
R1030
0.56
GP002
EARTH PLATE
T601 2.1 8 ADIM 9 1.9 OPEN
POWER TRANS R1031
R1011 C1007 0.56
24K 0.047 R1019
6 7 100K R1005 C1012 D1006 R1032
R1012 120 1 OPEN 0 GP003
C605 2.2K EARTH PLATE
330 R614 R1008 R1006 R1007 C1024 R1004
/200V 470K 10K 10K 100K OPEN 120
BC604 5 8
OPEN
R603
470K
BC601 9
BEAD
4 D655
SB3A0BH
10
R604 D653 C654 C655 C657 R663
470K SB3A0BH 470/16V 470/16V OPEN D654 D654A OPEN TO DIGITAL MAIN
2 11 1ZB20BB OPEN CN501 CBA UNIT CN3601
357.0 D Q601 23 NU
C606 TK6P60W C608 R606 R607 C650 22 PROTECT1(NU)
820P G (SWITCHING) 0.015 220 220 OPEN 3.3 21
/2KV 4.2 1 12 D656 PROTECT3
3.3 20
0.1 S C607 Q602
D650
SB3150BH
OPEN RESET
1800P 2SC5344SY 3.3 Q650 D663 3.3 19 BACKLIGHT-SW
2 D607
TFZVTR27B
4.2
0
SWITCHING
CONTROL
0.4
R608
1.5K
D605
MM5Z4V3B
D621
D651
SB3150BH
R651
1
D656A
RS1BJTD
Q658
C656 R693
1/50V OPEN
D657
MM5Z11B
R652
56K -2.3
R653
33K 0
KTC3875S
-Y-RTK/P
(RESET)
OPEN
R677
10K
3.2 18
2.7 17
3.3 16
P-ON-H2
BACKLIGHT-ADJ
AL+3.3V
1SS400ST D610 2SA1201-Y C661 0 15 GND
Q621 1SS400ST R690 (+3.3V REG.) OPEN 0 14
1.5 GND
KTC3875S C624 D623
-Y-RTK/P OPEN MM5Z30B R613 12.9 3.3 Q656 0 13 GND
OVER KTC3875S D664 C663
220 R673 12.3 -Y-RTK/P TFZVTR4.7B 100/10V 0 12 GND
VOLTAGE OPEN (SWITCHING)
0.4 PROTECT R621 0 11 GND
560 12.3 3.3
0 R662 0 10 GND
0 R623 C622 C621 C623 R670 R671 R672 3.8 3.3K 12.9 9
10K OPEN OPEN 4.7 IC602 270 270 270 R680 AMP+13V
TLP785F C665 R682 100 12.9 8
0.1 0 C638 AMP+13V
ERROR OPEN 12.9 7
VOLTAGE DET R655 R654 3.8 AMP+13V
14.2 20.3 180 180 2.5 12.9 6 AMP+13V
0 D662 R681
4 1
D609 R609 C610 R657 SL431A-AT 10K 0 5 GND
CES520 100 1500P 3.9K
0.4 3 2 19.3 20.7 4 P-ON+21V
C666 R659 C651 C652 C653 D652 D652A C658 C639 20.7 3 P-ON+21V
R615 R611 D608 D608A C609 R612 0.22 27K 470/25V 470/25V 470/25V 1ZB30BB OPEN OPEN OPEN
1ZB36BB OPEN 0.068 5.6K 20.7 2 P-ON+21V
OPEN 0.36 R660
/2W SA602 GT601 C660 R658 3.9K 20.7 1 P-ON+21V
OPEN OPEN 0.22 2.7K
R616 R675
OPEN 68K D661 R667
19.3 2.5 1SS400ST 8.2K
1 R617
OPEN
R618
C619
OPEN 0 D660
SL431A-AT R661
3.3K
0 R669
OPEN Q653 0.6 10K
KTC3875S-Y-RTK/P
R619 (SWITCHING) 0 R668
47K
OPEN
HOT COLD
A B C D E F
10-3 PL14.12SCP
CONTINUE
(NO CONNECTION) CN3905 DIGITAL 2
LCD+12V 1 LCD+12V/+21V
LCD+12V 2 CONTINUE
LCD+12V 3 DIGITAL 7
LCD+12V 4 P-ON+21V
GND 5 P-ON+3.3V
TO LCD PANEL
GND 6 CN3904 ASSEMBLY
GND 7 30 LCD+21V
PANEL-WP 8 R3909 29 LCD+21V
OPEN
LVDS-SEL 9 28 GND
4 NU 10
GND 11
LVDS-OD0(-) 12
R3910
OPEN 27 VCOM
26 PWR-CTRL
25 P-ON+3.3V
LVDS-OD0(+) 13 24 GND
GND 14 23 LVDS-OD0(-)
LVDS-OD1(-) 15 22 LVDS-OD0(+)
LVDS-OD1(+) 16 21 LVDS-OD1(-)
GND 17 20 LVDS-OD1(+)
LVDS-OD2(-) 18 19 LVDS-OD2(-)
LVDS-OD2(+) 19 18 LVDS-OD2(+)
GND 20 17 GND
LVDS-OCLK(-) 21 16 LVDS-OCLK(-)
LVDS-OCLK(+) 22 15 LVDS-OCLK(+)
GND 23 14 GND
LVDS-OD3(-) 24 13 LVDS-OD3(-)
LVDS-OD3(+) 25 12 LVDS-OD3(+)
GND 26 R3908 11 LVDS-OD4(-)
OPEN R3932
BIST 27 18K 10 LVDS-OD4(+)
PANEL-SCL 28 R3907 9 LVDS-OD5(-)
OPEN
PANEL-SDA 29 R3934 8 LVDS-OD5(+)
3.9K
GND 30 7 GND
CONTINUE R3931 R3933 C3947 C3948 6 TP
DIGITAL 2 11K 12K 47/25V 0.1
LVDS-OD4(+) R3935 5 POL
1K
3 LVDS-OD4(-)
LVDS-OD3(+)
LVDS-OD3(-)
R3924
OPEN
Q3901
2SC4081UBTLQ
(VCOM DRIVE)
4 CPV
3 OE1
2 OE2
1 STV
LVDS-OCLK(+)
LVDS-OCLK(-)
LVDS-OD2(+)
LVDS-OD2(-)
CN3903 (NO CONNECTION)
LVDS-OD1(+) 31 LCD+21V
LVDS-OD1(-) 30 LCD+21V
LVDS-OD0(+) 29 LCD+21V
LVDS-OD0(-) 28 GND
LVDS-ED4(+) *1
IC3101(1/7) 27 VCOM
LVDS-ED4(-) MN2WS0270HA 26 PWR-CTRL
LVDS-ED3(+) DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER 25 P-ON+3.3V
LVDS-ED3(-) R3916 24 GND
R3913 0x4 10K
LVDS-ECLK(+) L3 23 LVDS-OD0(-)
LVDS-ECLK(-) L4 22 LVDS-OD0(+)
LVDS-ED2(+) J6 K3 21 LVDS-OD1(-)
LVDS-ED2(-) K6 K4 20 LVDS-OD1(+)
LVDS-ED1(+) J5 19 LVDS-OD2(-)
LVDS-ED1(-) R3914 0x4
K5 J1 18 LVDS-OD2(+)
LVDS-ED0(+) L7 J2 17 GND
LVDS-ED0(-) LVDS
M7 TX J3 16 LVDS-OCLK(-)
H3
R3915 OPEN
15
14
13
LVDS-OCLK(+)
GND
LVDS-OD3(-)
LCD+12V 28 N5 H4 12 LVDS-OD3(+)
LCD+12V 27 M5 G3 11 LVDS-OD4(-)
GND 26 M6 F3 10 LVDS-OD4(+)
GND 25 F1 9 LVDS-OD5(-)
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
GND 24 K7 NU F2 8 LVDS-OD5(+)
PANEL-WP 23 J7 NU NU P1 7 GND
R3974 100
C3916
C3903
C3904
C3905
C3908
C3911
C3906
C3907
C3912
C3913
C3914
C3915
LVDS-SEL 22 TP R6 6 TP
R3975 100
NU 21 TO DIGITAL POL R3 5 POL
MAIN 6 R3976 100
GND 20 IC3101(5/7) CPV P3 4 CPV
R3977 100
LVDS-OD0(-) 19 OE N3 3 OE
R3978 100
LVDS-OD0(+) 18 OE2 R5 2 OE2
R3979 100
GND 17 STV P4 1 STV
OPEN
OPEN
OPEN
OPEN
100K
100K
100K
100K
100K
100K
OPEN
OPEN
OPEN
OPEN
OPEN
100P
LVDS-OD1(-) 16
3P
3P
3P
3P
3P
3P
3P
3P
LVDS-OD1(+) 15 CONTINUE
DIGITAL 4
R3884
R3928
R3883
R3882
R3881
R3880
C3928
C3917
C3918
C3919
C3922
C3923
C3920
C3921
C3924
C3925
C3926
C3927
C3942
C3998
C3941
C3940
C3939
C3938
GND 14
LVDS-OD2(-) 13 VCOM-PWM
LVDS-OD2(+) 12
GND 11 N2 NU CONTINUE
P2 NU DIGITAL 2
LVDS-OCLK(-) 10 VCOM-DC
1 LVDS-OCLK(+) 9
GND 8
LVDS-OD3(-) 7
R3901
10K
P7 BACKLIGHT-ADJ
VCOM-PWM
LCD-P-ON
PANEL-WP
LVDS-OD3(+) 6 PANEL-SCL
GND 5 PANEL-SDA
NU 4
R3906 OPEN
PANEL-SCL 3 CN3902 (NO CONNECTION)
R3904 OPEN
PANEL-SDA 2 1 GND
GND 1 2 PANEL-WP
R3925 3 PANEL-SCL
CONTINUE OPEN
DIGITAL 7
BACKLIGHT-ADJ DIGITAL MAIN CBA UNIT 4 PANEL-SDA
A B C D E F
10-4 PL14.12SCD1
CONTINUE
DIGITAL 7
P-ON+21V
P-ON+3.3V R3942
0
CONTINUE
DIGITAL 1 R3952 D3905 Q3905
OPEN OPEN
4 LCD+12V/+21V
D3906
OPEN
R3550 IC3901
C3996
OPEN
R3899
1
2
OPEN
8
7
OPEN OPEN OPEN
C3946 3 6
OPEN
1 SS BST 8 R3897 4 5
C3949 OPEN
OPEN
2 EN IN 7 R3891
R3990 C3951 C3945 C3944 C3943 OPEN
(NO CONNECTION) CN3906 OPEN OPEN OPEN OPEN OPEN
LCD+12V 1 3 COMP SW 6 R3895
OPEN Q3904
LCD+12V 2 C3992 C3991 4 FB GND 5 OPEN
OPEN OPEN R3898 C3997
LCD+12V 3 C3950 R3938 OPEN OPEN
OPEN OPEN
LCD+12V 4 C3955 R3937
OPEN R3936 OPEN R3939 L3901
NU 5 OPEN OPEN OPEN
GND 6 CONTINUE
DIGITAL 6
GND 7 R3912 R3911 C3959 C3958 C3952 D3901 C3954 C3956 C3953 P-ON-H2
GND 8 OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN
R3989 OPEN
GND 9
R3988 OPEN
GND 10
R3981 OPEN
LVDS-OD4(+) 11
R3980 OPEN
LVDS-OD4(-) 12
R3943 OPEN
3 LVDS-OD3(+) 13
LVDS-OD3(-) 14
GND 15
R3921 OPEN
CONTINUE
LVDS-OCLK(+) 16 DIGITAL 1
R3920 OPEN
LVDS-OCLK(-) 17 LVDS-OD4(+)
GND 18 LVDS-OD4(-)
LVDS-OD2(+) 19 LVDS-OD3(+)
LVDS-OD2(-) 20 LVDS-OD3(-)
R3919 OPEN
LVDS-OD1(+) 21 LVDS-OCLK(+)
LVDS-OD1(-) 22 LVDS-OCLK(-)
LVDS-OD0(+) 23 LVDS-OD2(+)
LVDS-OD0(-) 24 LVDS-OD2(-)
R3987 OPEN
GND 25 LVDS-OD1(+)
R3986 OPEN
GND 26 LVDS-OD1(-)
R3985 OPEN
LVDS-ED4(+) 27 LVDS-OD0(+)
R3984 OPEN
LVDS-ED4(-) 28 LVDS-OD0(-)
LVDS-ED3(+) 29 LVDS-ED4(+)
LVDS-ED3(-) 30 LVDS-ED4(-)
GND 31 LVDS-ED3(+)
LVDS-ECLK(+) 32 LVDS-ED3(-)
2 LVDS-ECLK(-) 33
GND 34
LVDS-ED2(+) 35
LVDS-ECLK(+)
LVDS-ECLK(-)
LVDS-ED2(+)
LVDS-ED2(-) 36 LVDS-ED2(-)
LVDS-ED1(+) 37 LVDS-ED1(+)
LVDS-ED1(-) 38 LVDS-ED1(-)
LVDS-ED0(+) 39 LVDS-ED0(+)
LVDS-ED0(-) 40 LVDS-ED0(-)
GND 41
R3866 OPEN
NU 42
R3867 OPEN CONTINUE
NU 43 DIGITAL 1
R3922 OPEN C3902 R3896 R3900 OPEN
NU 44 OPEN OPEN VCOM-DC
R3903 OPEN
VCOM 45 VCOM-PWM
R3905 OPEN
LCD-P-ON 46 LCD-P-ON
R3869 OPEN R3941 R3940 C3909 C3910
NU 47 OPEN OPEN OPEN OPEN PANEL-WP
R3926 OPEN
NU 48 PANEL-SCL
R3923 OPEN
PANEL-SDA 49 D3902 PANEL-SDA
R3902 OPEN 1SS400
PANEL-SCL 50
PANEL-WP 51 OPEN C3901
R3982 OPEN R3948 4.7
R3947 OPEN CONTINUE
1 R3983
R3918
R3917
OPEN
OPEN
OPEN
DIGITAL 8
PROTECT3
G H I J K L
10-5 PL14.12SCD2
*1
IC3101(2/7)
MN2WS0270HA
MAIN MICRO CONTROLLER
/DIGITAL SIGNAL PROCESS DIGITAL MAIN CBA UNIT CONTINUE
R3433 10K DIGITAL 7
DDRPWRON T5 AL+3.3V
R3421 270
MMVREF0 D3 VCC+1.5V
R3423 270
MMVREF1 D16
R3411 270 IC3401 IC3402
MMVREF2 D6
K4B1G1646G-BCK0 K4B2G1646Q-BCMA
MMDQ0 (DDR3 SDRAM) (DDR3 SDRAM)
MMDQ0 D7
0.1
270
0.1
270
0.1
270
MMDQ1 E6 MMDQ1
3 MMDQ25
MMDQ26
MMDQ27
A17
D15
C15
MMDQ25
MMDQ26
MMDQ27
MMDQ28
MMDQ11
MMDQ14
A3
B8
DQU7
DQU6
VSS1
VSS2
A9
B3
MMDQ19
MMDQ22
A3
B8
DQU7
DQU6
VSS1
VSS2
A9
B3
MMDQ28 B12 MMDQ10 MMDQ18
MMDQ29 A12 MMDQ29 A2 DQU5 VSS3 E1 A2 DQU5 VSS3 E1
MMDQ30 MMDQ12 A7 DQU4 VSS4 G8 MMDQ20 A7 DQU4 VSS4 G8
MMDQ30 D11 MMDQ8 MMDQ16
MMDQ31 C11 MMDQ31 C2 DQU3 VSS5 J2 C2 DQU3 VSS5 J2
MMDQ15 C8 DQU2 VSS6 J8 MMDQ23 C8 DQU2 VSS6 J8
MMDQS1 B4 MMDQ9 C3 DQU1 VSS7 M1 MMDQ17 C3 DQU1 VSS7 M1
MMXDQS1 A4 MMDQ13 D7 DQU0 VSS8 M9 MMDQ21 D7 DQU0 VSS8 M9
MMDQS0 A6 MMDQ6 H7 DQL7 VSS9 P1 MMDQ30 H7 DQL7 VSS9 P1
MMXDQS0 C6 MMDQ2 G2 DQL6 VSS10 P9 MMDQ26 G2 DQL6 VSS10 P9
MMDQS3 D17 MMDQ7 H8 DQL5 VSS11 T1 MMDQ31 H8 DQL5 VSS11 T1
MMXDQS3 C16 MMDQ3 H3 DQL4 VSS12 T9 MMDQ27 H3 DQL4 VSS12 T9
MMDQS2 B15 MMDQ4 F8 DQL3 VSSQ1 B1 MMDQ28 F8 DQL3 VSSQ1 B1
MMXDQS2 C14 MMDQ1 F2 DQL2 VSSQ2 B9 MMDQ25 F2 DQL2 VSSQ2 B9
MMDQ5 F7 DQL1 VSSQ3 D1 MMDQ29 F7 DQL1 VSSQ3 D1
MMDM1 C9 MMDQ0 MMDQ24
MMDM0 B2 E3 DQL0 VSSQ4 D8 E3 DQL0 VSSQ4 D8
MMDM3 C12 VSSQ5 E2 VSSQ5 E2
MMDM2 C19 VSSQ6 E8 VSSQ6 E8
L2 CS# VSSQ7 F9 L2 CS# VSSQ7 F9
R3405 56x4 MMA2 K3 CAS# K3 CAS#
MMA2 G11 VSSQ8 G1 R3403 C3403 VSSQ8 G1 R3401 C3401
MMA6 K1 ODT OPEN OPEN K1 ODT OPEN OPEN
MMA6 E8 VSSQ9 G9 VSSQ9 G9
MMA8 G8 MMA8 J3 RAS# R3427 J3 RAS# R3431
2 MMA14
MMA9
MMA11
E7
E19
F18
R3406 56x4
MMA14
MMA9
MMA11
R3428
L3
T2
L8
WE#
RESET#
ZQ
CK J7
CK# K7
CKE K9
220
R3404
OPEN
C3404
OPEN
R3432
L3
T2
L8
WE#
RESET#
ZQ
CK J7
CK# K7
CKE K9
220
R3402
OPEN
C3402
OPEN
R3409 56x4
MMBA2 G16
MMBA0 E15
MMXWE D14
MMXCAS E14
MMCK B10
MMXCK B9
R3418 56
MMXCS1 D12
R3417 56
MMXCS0 E11
R3416 56
MMODT0 F11
1 MEMORY
I/F MMODT1
MMCKE0
MMCKE1
F12
F10
G10
R3415
R3414
R3413
R3412
56
56
56
56
MMXRAS F14
MMXRESET F19
TO DIGITAL C3405 1
MAIN 6 DDR3VOUT D1 R3419 C3407
IC3101(5/7) R3420 240 10K OPEN
MMZQ D4
NU G7
NU G12
M N O P Q R
10-6 PL14.12SCD3
*1
IC3101(3/7)
MN2WS0270HA
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER C3125 C3126
0.1 0.1
4 CONTINUE
C3128
15P
C3124
X3101
25MHz
R3170
R3169
OPEN
AE4 AXI
10K
10K
10K
10K
COMP-DET H6 COMP-DET MMCDAT5 E20
MMCDAT6 4 NU NU 45 R3192
HP-DET G4 NU MMCDAT6 B20 56x4
R3132
R3121
R3124
R3173
R3111 R3112 M3 NU MMCDAT7 C20 MMCDAT7 5 NU I/O7 44 MMCDAT7
10K 100
L2 HP-DET MMCDAT6
6 NU I/O6 43
D20 NU
R3205 22 MMCDAT5
A20 NU NANDRYBY D22 7 R/B I/O5 42
R3201 75
W20 NU NFALE B23 MMCDAT4
R3202 75 8 RE I/O4 41
V20 NU NFCLE C23
R3203 75
Y22 NU TO DIGITAL XNFCE A23 9 CE NU 40
MAIN 6 R3190 75
CONTINUE AA22 NU IC3104(5/7) XNFWE A24
DIGITAL 7 R3189 75 10 NU NU 39
AB23 NU XNFWP B24
P-ON+3.3V R3208 R3204 75
OPEN W21 NU XNFRE E21 11 NU NU 38
P-ON+5V U20 NU NU C22
3 12 VCC VCC 37
R3128 10K
R3123 10K
AL+3.3V V21 NU NU F20
R3135
OPEN Y21 NU NU J24 13 VSS VSS 36
U19 NU NU J22
14 NU NU 35
W19 NU NU G24
V19 NU NU G23 15 NU NU 34
AB22 NU NU H23
(NO CONNECTION) CN3104 16 CLE NU 33 R3191
GND 10 U21 NU NU G22 56x4
NU H22 17 ALE I/O3 32 MMCDAT3
NU 9
EJTCK 8 AA7 NU NU K22 MMCDAT2
18 WE I/O2 31
JTDI 7 U9 NU NU J25
NU P22 19 WP I/O1 30 MMCDAT1
JTDO 6 AD8 NU
JTMS 5 AB7 NU NU P25 MMCDAT0
20 NU I/O0 29
TRSTN 4 Y8 NU NU R20
R3127 OPEN NU T21 21 NU NU 28
EVTRG 3 L21 NU
XRST 2 AC5 NU NU R22
22 NU NU 27
AL+3.3V 1 R3136 R3129
R3113 100 R3210 NU R21
10K 10K R3198 10K OPEN NU T20 23 NU NU 26
R3125 OPEN E24 NU NU T19
24 NU NU 25
G21 NU NU R19
CONTINUE
DIGITAL 8 R3130 E23 NU NU P24
2 STB-RESET
STMTIME1
OPEN
R3126
OPEN
D25
C25
D24
NU
NU
NU
NU
NU
NU
P21
AB18
Y18
J19 NU NU Y17
H19 NU NU W17
L20 NU NU W15
J23 NU NU AA17
L19 NU NU W18
N20 NU NU AC19
K19 NU NU Y16
N21 NU NU AD19
M20 NU NU W16
M19 NU NU Y20
J20 NU NU AB19
P20 NU NU AE20
K21 NU NU AB20
N19 NU NU AA18
R3224 1K
P19 NU NU AD20
R3115 OPEN
M21 NU NU AA21
F25 NU NU Y19
1 R3116 OPEN
R3118 1K
R3122 OPEN
H20
F23
F24
NU
NU
NU
NU
NU
NU
AA19
AA20
AC20
F22 NU
H21 NU
K20 NU
S T U V W X
10-7 PL14.12SCD4
CONTINUE
DIGITAL 7
P-ON+5V TU3001
TUNER UNIT
P-ON+3.3V
DIF-OUT1
DIF-OUT2
IF-AGC
+3.3V
*1
GND
SDA
SCL
IC3101(4/7)
MN2WS0270HA 1 2 3 4 5 6 7
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
CONTINUE M1 NU L3005
DIGITAL 8 2.2uH
UART1TX N4 NU
M2 NU C3041 C3040 C3039 D3007
UART1RX NU AB9 OPEN 10 OPEN MM5Z5V6B
P5 NU NU AC9
R3193 100
F21 UART1RX NU Y12
R3194 100
G20 UART1TX NU AA15 C3002 D3001
R3217 1K OPEN OPEN
(NO CONNECTION) CN3101 B25 NU NU W14
GND 4 D23 NU NU W10
R3176 100
UARTORX 3 C24 UART0TX NU Y13
R3175 100 C3003 D3002
UARTOTX 2 E22 UARTOTX NU W8 OPEN OPEN
P-ON+5V 1 NU AA8
C3115 C3116 R3101 C3117 R3108 C3011 L3003 R3005
OPEN OPEN 10K OPEN OPEN 0.1 3.3uH 270
AD9
3 (USB JACK)
USB+5V
USB0(-)
CN3704
1
2
L3706
OPEN
N22 USB0(-)
DEMODULATOR
/MPEG
DECODER
AE9
C3026
OPEN C3014
C3027
0.1
C3013
39P L3004
3.3uH
R3003
270
2 USB1(-)
USB1(+)
GND
3
2
1
R3735
M22 USB1(-)
L23 USB1(+)
NU U10
RX(-) AC8
R7
R6
R5
NU
RX(-)
RCT
OPEN RX(+) AC7 R4 RX(+)
R3734 R3736 TX(-) AE6 R3 TX(-)
0 0 R3180 10K
WIRELESS M23 USB10D R2 TCT
LAN MODULE CN3701
USB1(+) 1 TX(+) AD6 R1 TX(+)
IC3702 C3744 C3701
USB1(-) 2 OPEN 0.01 0.01
USB+5V 3 1 VOUT VIN 5
GND 4 C3716 C3715
OPEN 2 GND OPEN
GND 5
GND 6 3 /FLAG EN 4 M25 USB1VBUS
R3704 C3714
OPEN OPEN CONTINUE
DIGITAL 7
R3702 CTRL11 AC6 CTRL11
OPEN
C3129
1
1
DIGITAL MAIN CBA UNIT
Y Z AA AB AC AD
10-8 PL14.12SCD5
*1
DIGITAL MAIN CBA UNIT IC3101(5/7)
MN2WS0270HA
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
JK3701
COMPONENT-Y AE12 NU
/VIDEO-IN C3705 D3705 R3166 AC12 NU
39P OPEN 75
AD12 NU A/D
Y9 NU CONVERTER
COMPONENT
-Pb-IN C3770 D3701 R3163 Y10 NU
39P OPEN 75
AA9 NU
4 CONTINUE
DIGITAL 4
COMPONENT
-Pr-IN C3703
39P
D3704
OPEN
R3164
75
C3121
C3118
C3119
1
1
1
R3214
R3216
R3218
10
10
10
AC10 NU
AB10
AD11 TO DIGITAL
C3706 AB11 MAIN 3
COMP-DET 0.01 R3727 R3723 C3120 1 R3219 10 SW IC3101(2/7)
R3741 10K C3704 AC11
HP-DET C3720 100 1
33 100P C3109 1 R3220 100
Q3709 AD13
C3709 R3725 2SC4081UBTLQ R3724 C3113 1 R3221 100 TO DIGITAL
JK3706 1 220 10K AB13 MAIN 4
DIGITAL (BUFFER) C3114 1 R3222 100 IC3101(3/7)
AUDIO OUT AC13 DIGITAL
(COAXIAL) C3708 D3702 R3726 C3707 SIGNAL
100P OPEN 110 33P R3171 R3168 R3167 PROCESS
75 75 75 TO DIGITAL
MAIN 8
AUDIO(L)-IN R3155 100 IC3101(7/7)
C3710 R3708 D3703 Y11 VGA-HSYNC
56P 10K OPEN R3154 100
AA12 VGA-VSYNC
TO DIGITAL
MAIN 5
AUDIO(R)-IN C3711 R3709 D3707 R3147 36 C3103 1 IC3101(4/7)
56P 10K OPEN W11
R3148 36 C3104 1
AA11
JK3713 R3149 36 C3105 1
AB12
PC-RGB-IN R3145 36 C3102 1
AA10 TO DIGITAL
MAIN 1
IC3101(1/7)
1 6 11 E4 NU
R3195 10K
D2 NU
2 7 12 R3196 10K
F6 NU
R3197 10K
3 3
4
8
9
13
14
R3199 OPEN
G5
E3
SPDIF
NU
NU
F4
C3207 1 R3297 100K
5 10 15 AE14
C3208 1 R3298 100K
D3711 1SS400
AC14
OPEN
OPEN
OPEN
OPEN
OPEN
R3839 47K
R3838 47K
R3831 10K
R3830 10K
AB14 NU
AC15 NU TO DIGITAL
MAIN 8
D3717
D3716
D3715
D3714
D3713
AC16 NU IC3101(7/7)
AD16 NU AUDIO
I/F
CONTINUE AB16 NU
DIGITAL 7 D3712
1SS400 AE17 NU
P-ON+5V TO DIGITAL
AD17 MAIN 5
P-ON+3.3V AC17 IC3101(4/7)
AMP+13V AB17
AC18
CONTINUE
DIGITAL 8 E2 AUDIO-MUTE
VGA-SCL F5 ARC-OUT
VGA-SDA CONTINUE
DIGITAL 8
CONTINUE ARC-OUT
DIGITAL 2
P-ON-H2
R3733 R3751
2 R3809
10K
R3810
OPEN
3.3
C3713
R3728 220/6.3V
4.7K 47K
JK3801
HEADPHONE
R3729 R3737 R3746 C3712
R3738 220/6.3V R3743 JACK
3.3 10K 10K 10K 10K
C3825 C3824 C3842
R3811 R3826 2.2 0.047 10 R3731 R3740 R3752
1K OPEN OPEN OPEN OPEN
IC3803 Q3708
R3820 R3813 TPA3110D2PWPR OPEN
560 10 (AUDIO AMP) R3739 R3744
Q3821 OPEN OPEN Q3701
2SA1576UBTLQ OPEN
(SWITCHING) 1 PVCCL 28 R3732
C3830 R3812 CONTROL OPEN
OPEN 100K LOGIC Q3710
2 PVCCL 27 OPEN
R3713 C3718
R3822 C3805 1 C3801 0.22 OPEN OPEN
10K 3 26
CONTINUE POWER PWM DRIVE L3801
DIGITAL 7 R3832 C3818 1 LIMIT LOGIC 10uH
R3823 22K 4 25
HP-MUTE 1.8K R3805 OPEN R3801 C3811 C3820 C3834 C3838 D3801
AUDIO-MUTE R3824 5 GND 24 OPEN 1000P 1 OPEN OPEN OPEN
10K Q3822 GAIN C3807
LCD-P-ON 2SC4081UBTLQ R3806 0 CONTROL OPEN L3802
(SWITCHING) 6 23
R3825 DRIVE 10uH
CONTINUE 47K C3802 0.22
DIGITAL 8 R3828 7 AVCC 22
OPEN R3802 C3812 C3821 C3835 C3839 D3802
SP-MUTE C3815 R3807 OPEN C3803 0.22 OPEN 1000P 1 OPEN OPEN OPEN
1 8 GND 21 C3808
C3816 1 DRIVE OPEN L3803
9 GVDD 20 10uH SP3801
R3808 CN3801 SPEAKER
C3817 1 10K
1 R3814
OPEN
R3817
OPEN
R3821
560
C3819 1
C3806 1
10
11
POWER
LIMIT
PWM
LOGIC DRIVE
GND 19
18
C3827
0.047
C3804 0.22
C3828
2.2
R3803
OPEN
C3809
OPEN L3804
10uH
C3813
1000P
C3822
1
C3836
OPEN
C3840 D3803
OPEN OPEN 1
2
3
SP(L)+
SP(L)-
SP(R)-
L-CH
12 17 4 SP(R)+ SP3802
R3815 R3818 R3833 R3804 C3814 C3823 C3837 C3841 D3804 SPEAKER
OPEN OPEN 22K 13 NU PVCCR 16 OPEN 1000P 1 OPEN OPEN OPEN R-CH
C3810
R3816 R3819 14 PBTL PVCCR 15 OPEN
OPEN OPEN C3831 C3826 C3829 C3843
OPEN 220/16V 220/16V 10
AE AF AG AH AI AJ
10-9 PL14.12SCD6
CONTINUE
DIGITAL 1
P-ON+21V
P-ON+3.3V
CONTINUE
DIGITAL 2 C3182
P-ON+21V C3630 2700P
OPEN
P-ON+3.3V R3630
0 *1
IC3604 R3626 IC3101(6/7)
CONTINUE RT8293ALZSP 0 MN2WS0270HA
DIGITAL 6 R3609
4 HP-MUTE
AUDIO-MUTE
LCD-P-ON R3610
OPEN
R3611
OPEN
10K
C3639
0.01
(+1.14V REG.)
1 BS
2 VIN
SS 8
EN 7
C3601
0.015
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
AFB R4
R3223
0
Q3601 C3183
OPEN C3645 C3655 C3656 C3654 OPEN
R3612 4.7 0.1 0.1 OPEN 3 SW COMP 6
CONTINUE OPEN C3638 R3181 C3134
DIGITAL 8 4 GND FB 5 0.015 0 1
STB-RESET R3676 AVDDVAD11 U12
OPEN R3613 R3625
LCD-P-ON OPEN 2.2K LVVDD11 K11
R3624 VDD11 *A C3132 C3136 C3142 C3138
BACKLIGHT-SW L3601 OPEN L3102 1 10 10 1
10uH 0
PROTECT3 AVDDH11 AC21
PROTECT1 R3689 C3646 C3641 C3643 C3642 C3644 C3139 C3143 C3144 C3130 C3131
OPEN OPEN 10 10 OPEN OPEN AVDDH11 AD21 1 1 1 0.1 0.1
P-ON-H2 C3133
HP-MUTE C3969 OPEN CONTINUE
OPEN DIGITAL 5
AVDD11-CEN T9 CTRL11
R3607 IC3601 AVDD11-RX AB4 C3147 C3148 C3149
56K C3605 0.1 0.1 0.1
R3601 PST8429UR 1000P DVDD11 T10
CONTINUE OPEN (RESET) C3616 C3615 C3609
DIGITAL 1 R3602 4.7 0.1 OPEN VDD33-1 N12
BACKLIGHT-ADJ 220 1 GND OUT 4 IC3603 VDD33-2 N13 C3178 C3179 C3156 C3157 C3158
MP1472GJC452Z 1 1 10 0.1 0.1
D3601 2 VDD CD 3 (+3.3V REG.) DPAVDD33 M12
TO POWER SUPPLY OPEN D3603 C3606 C3607
3 CBA CN501
NU
PROTECT1(NU)
PROTECT3
CN3601
1
2
3
R3620 100
R3603 100
OPEN
R3608
270
C3602
1 0.01
C3604
0.033
R3606 C3611
11K 3300P
1 SS
2 EN
BST 8
VIN 7 C3612
0.01
AVDDH33
VDDEM18-33
LVVDD33-1
LVVDD33-2
AB21
M13
L11
M11 C3155
L3101
BEAD
2 P-ON+21V
P-ON+21V
P-ON+21V
P-ON+21V
20
21
22
23
C3676
OPEN
D3605
MM5Z15B
Q3602
R3622
10K
C3665 R3627
OPEN 100K
R3635 C3666
5.1K 4700P
2 EN
3 COMB
4 FB
VIN 7
SW 6
GND 5
0.01 VDDSD18-33 J21
AVDD33-CEN P10
C3169
0.1 L3106
BEAD
R3615 2SA1576UBTLQ D3609 C3613
10K (SW+12V) OPEN OPEN R3633 R3679 AVDD33-TX P9 C3170 C3171 C3177
10K 6.2K 0.1 0.1 10 R3184
CONTINUE 0
DIGITAL 6 D3608 R3095 R3634 L3603 VDDTCON25-33 M9
R3618 1SS400 10K 100 10uH
P-ON+5V 4.7K C3168
0.1 CONTINUE
P-ON+3.3V R3619 C3668 C3672 C3670 C3671 C3669 R3685 DIGITAL 3
Q3603 10K 470/4V 10 10 10 OPEN OPEN
AMP+13V 2SC4081UBTLQ STMADAVDD33 M10 AL+3.3V
(SWITCHING) R3621 C3610 C3968 C3174 C3173 C3172
OPEN 1 OPEN STMRONA T4 0.1 10 1 VCC+1.5V
CONTINUE VDDSTM33 L10
DIGITAL 4
P-ON+3.3V VDDIO15 *B
P-ON+5V C3625 C3632 C3631 C3153 C3152 C3141 C3145 C3146 C3150
4.7 0.1 OPEN 10 1 1 1 1 1
AL+3.3V IC3607
MP1472GJC452Z
(+5V REG.) C3137 C3140 C3151 C3184 C3185
CONTINUE R3631 C3617 1 1 1 1 1 L3108
DIGITAL 5 0 0.1 BEAD
P-ON+5V 1 SS BST 8 VDDIOCK15 D5
P-ON+3.3V 2 EN VIN 7 C3620 VDDSTM11 N10 C3154
R3614 C3619 0.01 0.1
R3623 C3618 4.3K 4700P FPEN N9 C3175
22K OPEN 3 COMB SW 6 1
1 CONTINUE
DIGITAL 8
P-ON+5V
P-ON+3.3V
D3606
1SS400 R3617
10K
R3678
12K
4 FB GND 5
TESTSEL
NU
GND
R12
*C
*D
*A:J11~J17,K12~K17,L14~L17,M15~M17
*B:E9,F8,F9,G13~G15,G19
R3616 *C:H5,P23,R13,R23,R24,T13,T22,T23,U22,U24,U25,
AL+3.3V 33K L3605 R3022 0 V5,AD1,AD2,AE2
22uH
R3023 0 *D:A1,A9,A25,C10,D13,E5,E6,E12,E13,F7,F13,F15,
D3615 C3628 C3621 C3623 R3696 HEAT SINK G17,G18,H7,H8,J9,J10,K9,K10,L9,L12,L13,M14,
KDZTR6.8B 10 10 OPEN OPEN R3024 0 N6,N7,N14~N17,P11~P17,R10,R11,R14,R17,T11,
T12,T14,T17,U13,U14,U16,U17,W12,W13,Y14,
AA14,AC4,AE1,AE25
DIGITAL MAIN CBA UNIT C3966
OPEN
AK AL AM AN AO AP
10-10 PL14.12SCD7
4 R3188
OPEN
R3200
OPEN
R3209
OPEN
R3109 10K
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
JK3717
HDMI-
CONNECTOR-1
R3206 AA4 NU AD24 1 DATA2(+)
OPEN Q3108 Y1 NU
OPEN AE24 2 TMDS DATA2 SHIELD
R3215 AB1 NU AD23 3 DATA2(-)
R3207 OPEN AB3 NU
OPEN AE23 4 DATA1(+)
(NO CONNECTION) CN3103 AB2 NU
AL+3.3V 1 AC23 5 TMDS DATA1 SHIELD
Y4 NU AE22 6 DATA1(-)
P-ON-H2 2 V6 NU
R3131 AD22 7 DATA0(+)
1K R3212 AA3 NU
100K AC22 8 TMDS DATA0 SHIELD
V4 NU Y23 9 DATA0(-)
CONTINUE AA24 10 CLOCK(+)
DIGITAL 2 R3120 AA23 11 TMDS CLOCK SHIELD
PROTECT3 OPEN
W4 LED2 HDMI AB25 12 CLOCK(-)
C3100 Q3103 R3143 I/F
CONTINUE OPEN OPEN OPEN AB24 13 HDMI-CEC
DIGITAL 7 AC25 14 ARC
P-ON+5V AC24 15 HDMI-CLOCK
P-ON+3.3V AD25 16 HDMI-DATA
AL+3.3V U23 R3721 R3718 R3706 17 GND
R3096 10K 47K 47K
22K V24 18 +5V
TO IR SENSOR CBA C3702 R3722 R3703 R3705
UNIT CN4052 CN3105 Y5 SW-EN V23 0.1 47K 10K 1K 19 HOT PLUG DETECT
SDA(NU) 1 U3 REMOTE V22
3 SCL(NU)
GND
KEY-IN1
2
3
4
R3117
10
R3107
100
C3107
R3146
100K
V3 LED1 W23
W22
Y25
R3701
10K Q3707
2SC4081UBTLQ
(SWITCHING)
R3719
OPEN
JK3716
1
HDMI-
CONNECTOR-3
DATA2(+)
REMOTE 5 OPEN R3102 Y24
1K 2 TMDS DATA2 SHIELD
LED1 6 R3323
OPEN Q3102 3 DATA2(-)
LIGHT 7 OPEN
P-ON+5V 8 C3110 C3112 R3119 C3108 (BUFFER) 4 DATA1(+)
OPEN OPEN OPEN OPEN
C3111 AUDIO VIDEO 5 TMDS DATA1 SHIELD
AL+3.3V 9 0.1 DECODER DECODER
C3101 6 DATA1(-)
0.1 Q3101 R3106 R3159 7 DATA0(+)
C3122 OPEN 2SC4081UBTLQ OPEN OPEN
(LED DRIVE) T3 LIGHT-SENS 8 TMDS DATA0 SHIELD
CONTINUE C3123 OPEN R3103 R3104 C3106 R3182 TO DIGITAL TO DIGITAL
DIGITAL 4 OPEN OPEN OPEN 10K MAIN 6 MAIN 6 9 DATA0(-)
STB-RESET R3105 IC3101(5/7) IC3101(5/7) 10 CLOCK(+)
R3110 R3114 100 R3179 100
STMTIME1 33 33 U1 KEY-IN1 HDMI-CEC Y3 11 TMDS CLOCK SHIELD
D3101 STMCECPUL T6 12 CLOCK(-)
MM5Z5V6B R3150 R3161 100 R3134 39
10K T2 PROTECT3 HDMI0-SCL T7 13 HDMI-CEC
CONTINUE R3160 100 R3137 39
DIGITAL 7 U5 PROTECT1 HDMI0-SDA W6 14 NU
R3139 39
STB-RESET AD5 STB-RESET HDMI1-SCL R9 15 HDMI-CLOCK
R3162 22 R3140 39
LCD-P-ON W2 LCD-P-ON HDMI1-SDA AE3 16 HDMI-DATA
R3133 100 R3141 39 R3781 R3780
BACKLIGHT-SW W3 BACKLIGHT-SW HDMI2-SCL V7 R3784 47K 47K 17 GND
R3142 39 10K
PROTECT3 Y2 P-ON-H2 HDMI2-SDA AA5 18 +5V
PROTECT1 C3759 R3785 R3710 R3779 19 HOT PLUG DETECT
R3138 OPEN 0.1 47K 10K 1K
P-ON-H2 AB6 P-ON-H2
HP-MUTE W7 HP-MUTE HDMI0-HPD R7 R3707 R3783
10K Q3702
2 CONTINUE
DIGITAL 6
SP-MUTE
W5 STMTIME1
AA2 SP-MUTE
HDMI1-HPD U2
HDMI2-HPD U6
HDMIO-5V AB5
2SC4081UBTLQ
(SWITCHING)
OPEN
JK3715
1
HDMI-
CONNECTOR-2
DATA2(+)
2 TMDS DATA2 SHIELD
HDMI1-5V AA6 3 DATA2(-)
HDMI2-5V AC3 4 DATA1(+)
R3863
C3127 27K 5 TMDS DATA1 SHIELD
0.1 R3152 R3153
IC3103 4.7K 4.7K D3722 6 DATA1(-)
1SS400
M24C16-WMN6TP R3865 7 DATA0(+)
(MEMORY) R3156 39 22
AC2 STM-SCL 8 TMDS DATA0 SHIELD
1 A0 VCC 8 R3157 39 R3165 39 9 DATA0(-)
AC1 STM-SDA VGA-SCL Y7
R3158 22 R3178 39 10 CLOCK(+)
2 A1 WP 7 U4 STM-EEPROM-WP VGA-SDA AD3
NU U7 11 TMDS CLOCK SHIELD
3 A2 SCL 6 R3151
10K HDMI-UART-CTRL Y6 12 CLOCK(-)
4 VSS SDA 5 13 HDMI-CEC
14 NU
R3730 C3719 15 HDMI-CLOCK
0 220P 16 HDMI-DATA
R3777 R3773 R3774 17 GND
Q3706 R3714 10K 47K 47K
OPEN 10K Q3704 18 HDMI+5V
2SC4081UBTLQ C3750 R3778 R3712 R3775 19 HOT-PLUG-DETECT
R3720 (SWITCHING) 0.1 47K 10K 1K
R3771 33K
1 R3772
OPEN
OPEN
C3717
R3711
10K Q3703
2SC4081UBTLQ
(SWITCHING)
R3776
OPEN
220P
R3717
0
CONTINUE R3715
DIGITAL 5 Q3705 10K
2SC4081UBTLQ CONTINUE
UART1TX (SWITCHING) R3716 DIGITAL 6
UART1RX 33K VGA-SCL
VGA-SDA
AQ AR AS AT AU AV
10-11 PL14.12SCD8
D4002
OPEN
R4006 R4005 R4004 R4003 R4002 R4001
2.2K 2.2K 2.7K 4.7K 8.2K 18K
A B C
10-12 PL14.12SCF
C4054
RS4051 R4060 R4053 0.1
RS-272 OPEN 15K
(REMOTE SENSOR)
V-OUT
D4051
GND
Vcc
SMLE12WBC7W1HR
1 2 3 POWER
2 R4051
56
R4052
6.8K TO DIGITAL MAIN
R4054 CN4052 CBA UNIT CN3105
1K
1 AL+3.3V
2 P-ON+5V
3 LIGHT
C4051 C4056 C4052
10 10 1000P 4 LED1
C4053 C4055 5 REMOTE
0.1 R4055 R4059 OPEN
OPEN OPEN 6 KEY-IN1
7 GND
8 SCL(NU)
IC4051 9 SDA(NU)
OPEN
1 IOUT GC2 6
R4057 2 GND GC1 5
OPEN
3 VCC NU 4 R4058 R4056
OPEN OPEN
C4057
OPEN
1 TO FUNCTION CBA
UNIT CN4001 CN4051
GND 1
KEY-IN1 2
A B C
10-13 PL14.12SCIR
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
BA4GF0F0102 1
D
A
J310 GND
B J302
2 VLED
1 ILED
GND
GP003 GP001
D660
J301
GND
CN1001
J313
C602
J101
P-ON+21V C1020
C6
19
GND
J102
P-ON+21V
J601
FG
C653
VLED1
J111
IC602
C1017
C1018
1
C1003
TOOL NO.
No.1
A B C D E F G H I J
GATE
C652
J605
SOURCE
D652
J606
50
D6
R1015
C603
J103
D603 P-ON+21V
L1001
C1021
D608 C651
51
D6
JS604
JS603
C606
C650
D6
R602
04
J609
J608
D6
J607
J104
+B
+B
02
T601 P-ON+21V
D6
J105
01
J202
J108
C614 1
11 00
DRAIN
DRAIN
R6 D1
DRAIN
P-ON+21V
2
P-ON
AMP+13V
GND
D6
C1019
54
H2+
PROTECT3
5
C60
J208
LDR
BC601
BC604
J214
OVP
J215 CDR
D6
53
J207
ISW
J213
J304
C655
L601
D6
56
D6
D656
J300
55
J602 GND
BON
J205
FG
J106
Anode
HOT
D P-ON+21V
COLD
C616
J112
J209
J306
CFB
GND
REG50
AMP+13V
J212
Q650
C657
J204
C618 C617
Base
J203
AMP+13V
J109
C658 C654
P-ON
C604 C656
BL-SW
SA601
J210
J311
BL-ADJ
J305
J211
GND
J309
H2+
GND
GND
R601
C663
BLACK WHITE
J308
GND
LIVE NEUTRAL
SA602 GT601
CN601
F602 ALL+3.3V
2 22 CN501 J307
T 2.5A L/250V
D662
GND
RISK OF FIRE-
Mountain
fold
REPLACE FUSE AS MARKED 1 23
Mountain fold
10-14 BA4GF0F01021
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
BA4GF0F0102 1
A
D
GND
B
J302 J310
1
GND
GP001 GP003
Q653
D660
R667
J301
GND
CN1001 R661
J101 C666
J313
C602
C1020 P-ON+21V R675 R668
19
C6
J102
GND
R657
P-ON+21V R658
R608
J601
C660
FG
C1001 Q602
C1017
1
C1018
R613 C621
SOURCE
D652
R606
J606
R621
D621 D623
D6
C603
D1004 C624
J103
C1014
P-ON+21V
R615 D603
R1023
L1001
C651 D608
C1021
D6
51
D1003 R616
R1017 C606
JS603
JS604
C650 R617
04
D6
R602
R618
J609
J608
J104 R619
02
+B
+B
D1001A
J607
R1016 P-ON+21V D6
L1002 T601
D608A
J105
01
L1003 D652A D6
R1025 D1
R6
J202
00 C614
J108
1 11
Q601
2
P-ON+21V
P-ON
AMP+13V
GND
54
R1030 C60
D607 5
R1021 R651
R604
J208
LDR
R1013
BC601
R1031
BC604
R1028
J214
OVP
C1008
CDR J215
R1005 53 D656A
C1012 D6
J207
R1001
ISW
D1006
R1027
J213
J304
C1009
R1032 C655
L601
R1026
56
C1024
D6
D656
J602
D6
GND
J205
R1003 FG
R1014
P-ON+21V
C616
R1006 R663 J112
J209
J306
CFB
C1004 AMP+13V
GND
REG50
J212
C657
R1008 R693
C1013 C617 C618
J204
C1025
J203
Base
R1009 IC1001
R1010
R1019 C1010
C1007
AMP+13V
C654
J109
C658
R1012 R670
D654A C604
P-ON
R1011 C656
R1020 SA601
Q650
BL-SW
J210
C1011
J311
R671 R673
J305
J211
GND
BL-ADJ
H2+
J309
GND
C639
GND
C663
Q656 R653
C661
C665 C638
D663
J308
GND
Q658 R677
R682
GT601 SA602
J110 GND J312
CN601
D664
F602
GP002
ALL+3.3V
R680 R662
J307 CN501 22 2
R681
GND
T 2.5A L/250V
D662
23 1
10-15 BA4GF0F01021
CL3801
1 4
TUNER UNIT CN3105 CN4052 CN4051 CN4001
CN3801
1 9 1 1
CL3101 CL3102
COMPONENT IR SENSOR CBA UNIT FUNCTION CBA UNIT
-Y/VIDEO-IN
9 1 2 2
COMPONENT
-Pr-IN AC CORD
AUDIO(L)-IN
REAR
AUDIO(R)-IN
B W
DIGITAL CN601
11-1
AUDIO-OUT
(COAXIAL)
HDMI- CN1001
CONNECTOR-2
1 2
HDMI-
CONNECTOR-3
SIDE PC-RGB-IN
CN3904
1
CL3006
USB JACK WIRELESS
LAN MODULE
LCD PANEL ASSEMBLY
30
HEADPHONE
JACK
PL14.12WI
EXPLODED VIEWS
A16 LCD1
CL3006
A5
A20
A13
A9
Digital Main CBA Unit
B23
B23
A17
B12
CL3701
CL3101
32PFL4909/F7, A3
32PFL4609/F7
CL3102
L23
IR Sensor CBA Unit B18 L27
L23 L23
B17
Function CBA Unit
A7
A8
AC601
Power Supply CBA B18
L27
CL3801
SP3801
B17
B10 S7
L23
SP3802
L9
L27
X6
L9
A15
S7
A11
See Electrical Parts List SSK1
for parts with this mark. SA1 32PFL4609/F7 32PFL4909/F7,
32PFL4909/F8
SSK1
SBA1
12-1 PL14.12-A_CEX
A11 X4 X2
S3
SBA1
32PFL4909/F7, Tape
32PFL4909/F8
S7
X1
Packing Tape
S6
X3
PCB Label
S4
32PFL4909/F8
S4 Packing Tape
S12
FR FR
ON S7
ON
T T
S1
Packing Tape
Some Ref. Numbers are
not in sequence.
12-2 PL14.12-A_PEX
Downloaded from www.Manualslib.com manuals search engine
PARTS LIST [32PFL4909/F7 (Serial No.: ME1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a LCD PANEL ASSEMBLY#
# have special characteristics important to safety.
Ref. No. Description Part No.
Before replacing any of these components, read
LCD1# LCD PANEL ASSEMBLY U44F4PA
carefully the product safety notice in this service
Consists of the following
manual. Don't degrade the safety of the product
A5 DECORATION PLATE A4DFAUT 2EMH00294
through improper servicing.
A9 LED LENS A4DFAUT 2EMM00301A
NOTE: Parts that are not assigned part numbers A20 LEADING EDGE COVER A4DFAUT 2EMM00288
(---------) are not available. CL3006 FFC WIRE ASSEMBLY 30PIN(W/SHIELD) 30P/ WX1A4DF2P401
FFC/SHIELD/629MM
Ref. No. Description Part No. LCD MODULE ----------
A3 REAR CABINET A4DFAUT 2EMM00312
A7 FUNCTION KNOB A4GF1UT 2EMM00237
A8 KNOB FRAME A4DFAUT 2EMM00325
A11 STAND NECK A31M2UT 1EM228000A
A13 JACK HOLDER A3RF0UT 1EM334677
A15# RATING LABEL A4DF2UT ----------
A16 LOGO LABEL A4DFAUT ----------
A17 ENERGY GUIDE LABEL A4DF2UT ----------
AC601# AC CORD W/O A GND WIRE UL/CSA/1775/NO/ WAC172LTE010
BLACK
B10 STAND HOLDER A4GF1UT 2EMM00233
B12 SENSOR SHIELD A4GF1UT 2EMS00133
B17 WALL_MOUNT_BRACKET A11N0UH 1EM434637
B18 WALL_MOUNT_COVER A2170UT 1EM332137
B23 WIRE LABEL A3AF0UT ----------
CL3101 FFC WIRE ASSEMBLY 9PIN 9PIN/WHITE/ WX1A4GF0S112
292MM
CL3102 WIRE ASSEMBLY 2PIN 2PIN/339MM WX1A4GF0C312
CL3701 FFC WIRE ASSEMBLY 23PIN 23PIN/WHITE/ WX1A4DF2S121
213MM
CL3801 WIRE ASSEMBLY 4PIN 4PIN/ WX1A4GF0C321
56MM&61MM&362MM
L9 SCREW BIND BLACK_NI +P-TITE M3X12.0 GBHP3120
3X12 BIND HEAD+ BLK
L23 SCREW BIND 3CHROM +S-TITE M3X6.0 M3X6 GBJS3060
BIND HEAD+
L27 SCREW BIND BLACK_NI +S-TITE M3X8.0 GBHS3080
M3X8 BIND HEAD+
SBA1 STAND BASE ASSEMBLY A31M2UT 1ESA34000
SP3801 SPEAKER MAGNETIC 8OHM/8W S0310F14 DS08110XQ002
SP3802 SPEAKER MAGNETIC 8OHM/8W S0310F14 DS08110XQ002
SSK1 STAND SCREW KIT A31M2UT(SCREW BIND 1ESA34003
BLACK_NI +P-TITE M4X25.0 )
PACKING
S1 CARTON A4DF2UT 2EMC00338
S3 STYROFOAM TOP A4GF1UT 2EMC00274
S4 STYROFOAM BOTTOM A4GF1UT 2EMC00275
S6 SET BAG A31F0UT 2EMC00088
S7 SERIAL NO. LABEL A4GF1UT ----------
ACCESSORIES
X1 POLYETHYLENE BAG HDPE 180X340XT0.03 1EM435579
X2# OWNERS MANUAL A4DFAUT 2EMN00159
X3 REMOTE CONTROL UNIT YKF340-003 URMT41JHG003
X4 BATTERY DRY R03(SIZE AAA ) XB00M0RKT001
X6 QUICK START GUIDE A4DF2UT 2EMN00165
2. Tolerance of Capacitors and Resistors are noted C607 CHIP CERAMIC CAP. B K 1800pF/50V CHD1JK30B182
C608 CHIP CERAMIC CAP.(1608) B K 0.015F/50V CHD1JK30B153
with the following symbols.
C609 CHIP CERAMIC CAP. B K 0.068F/50V CHD1JK30B683
IC3803 IC D-CLASS AUDIO POWER AMPLIFI NSCA0T0TY073 C1007 CHIP CERAMIC CAP.(1608) B K 0.047F/25V CHD1EK30B473
TPA3110D2PWPR C1008 CHIP CERAMIC CAP. B K 560pF/50V CHD1JK30B561
TU3001 TUNER UNIT U9004UT U9004UT C1009 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
When you replace one of the below ICs on this CBA, always replace the C1010 CHIP CERAMIC CAP.(1608) B K 0.22F/25V CHD1EK30B224
IC in accordance with the 4 combinations below. Do not mix ICs of
different combination. C1012 CHIP CERAMIC CAP.(1608) B K 1F/25V CHD1EK30B105
IC3401 IC 1GB DDR3 SDRAM K4B1G1646G-BCK0 NSCA0R0SM055 C1013 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
IC3402 IC 2GB DDR3 SDRAM K4B2G1646Q-BCMA NSCA0R0SM057 C1014 CHIP CERAMIC CAP.(3216) X7R K 1.0F/100V CA2A105MR080
or C1015 CHIP CERAMIC CAP.(3216) X7R K 1.0F/100V CA2A105MR080
IC3401 IC 1GB DDR3 SDRAM H5TQ1G63EFR-PBC NSCA0R0HY039 C1017 CAP ELE 47F/100V/M/85 CEH4700V8006
IC3402 IC 2GB DDR3 SDRAM H5TQ2G63FFR-PBC NSCA0R0HY041 C1018 CAP ELE 47F/100V/M/85 CEH4700V8006
or C1021 CAP ELE 47F/100V/M/85 CEH4700V8006
IC3401 IC 1GB DDR3 SDRAM NT5CB64M16FP-DH NSCA0R0J2017 CONNECTORS
IC3402 IC 2GB DDR3 SDRAM NT5CB128M16FP-DI NSCA0R0J2016 CN501 FPC/FFC CONNECTOR IMSA-9615S-23C-PP- JC96J23ER009
A
or
CN601# CONNECTOR S2P3-VH (LF)(SN) JCVHC02JG002
IC3401 IC 1GB DDR3 SDRAM H5TQ1G63EFR-PBC NSCA0R0HY039
CN1001 PH CONNECTOR TOP 2P B2B-PH-K-S J3PHC02JG029
IC3402 IC 2GB DDR3 SDRAM H5TQ2G63DFR-PBC/ NSCA0R0HY034 (LF)(SN)
FBGA
DIODES
D601# DIODE 1N5397BD NDL1001N5397
MSW ASSEMBLY D602# DIODE 1N5397BD NDL1001N5397
D603# DIODE 1N5397BD NDL1001N5397
Ref. No. Description Part No.
D604# DIODE 1N5397BD NDL1001N5397
MSW ASSEMBLY A4DFAMSW-001
Consists fo the following D605 ZENER DIODE MM5Z4V3B ND1BMM5Z4V3B
FUNCTION CBA UNIT A4DFAMSW-001-FN D607# ZENER DIODE SMD TFZVTR27B QD1B00TFZV27
IR SENSOR CBA UNIT A4DFAMSW-001-IR D608# DIODE ZENER 1ZB36BB NDWZ0001ZB36
D609 DIODE SCHOTTKY SMD CES520.L3F(D QD1Z00CES520
D610 DIODE SWITCHING SMD 1SS400ST(SOD-523) ND1Z1SS400ST
R601# RES. CARBON FILM J 1/2W J 1.2M RCX2125T1003 R1029 RES CHIP 3216 1/4W F 0.75 RTR750RYL007
R602 RES CEMENT 5W J 2.7 RWJ2R7PAK007 R1030 RES CHIP 3216 1/4W F 0.56 RTR560RYL007
R603 RES CHIP 3216 1/4W J 470k RRX4474HH034 R1031 RES CHIP 3216 1/4W F 0.56 RTR560RYL007
R604 RES CHIP 3216 1/4W J 470k RRX4474HH034 R1032 RES CHIP 3216 1/4W 0 RRX4000HH036
Chassis PL14.12
2014/02/18 32PFL4909/F7 (Serial No.: ME1) added
2014/03/04 32PFL4609/F7 (Serial No.: ME1) First draft added
2014/03/24 32PFL4909/F8 (Serial No.: ME1) First draft added
14-1 PL14.12REV
Downloaded from www.Manualslib.com manuals search engine
COMPARISON LIST OF MODEL NAMES
Chassis PL14.12
32PFL4909/F7 (ME1) A4DF2UT
PL14.12COM
Downloaded from www.Manualslib.com manuals search engine