Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Command: LINE
Specify first point: (Pto. 1)
Specify next point or [Undo]: @0,20
Specify next point or [Undo]: @21,10
Specify next point or [Undo/Close]:@0,-4
Specify next point or [Undo/Close]: @-13,0
Specify next point or [Undo/Close]: @-13,0
Specify next point or [Undo/Close]: @0,-10
Specify next point or [Undo/Close]: @14,0
Specify next point or [Undo/Close]: @0,-6
Command: LINE
Specify next point or [Undo/Close]: @-22,0
Specify first point: (punto 1)
Specify next point or [Undo/Close]:
Luego, dirigir el cursor hacia arriba y teclear 15
Specify next point or [Undo]: 15 EJERCICIO PROPUESTO
Luego, dirigir el cursor hacia la izquierda y teclear 40 Utilizando el comando LINE realizar el siguiente dibujo
Specify next point or [Undo]: 40
Luego, dirigir el cursor hacia arriba y teclear 20
Specify next point or [Undo/Close]: 20
Luego, dirigir el cursor hacia la derecha y teclear 35
Specify next point or [Undo/Close]: 35 1
Pto.
Luego, dirigir el cursor hacia larriba y teclear 15
Specify next point or [Undo/Close]: 15
Luego, dirigir el cursor hacia la izquierda y teclear 35
Specify next point or [Undo/Close]: 35
Luego, dirigir el cursor hacia arriba y teclear 201
Pto.
Specify next point or [Undo/Close]: 20
Luego, dirigir el cursor hacia la derecha y teclear 40
Specify next point or [Undo/Close]: 40
Luego, dirigir el cursor hacia arriba y teclear 15
Specify next point or [Undo/Close]: 15
Luego, dirigir el cursor hacia la izquierda y teclear 60
Specify next point or [Undo/Close]: 60
Luego, dirigir el cursor hacia abajo y teclear 85
Specify next point or [Undo/Close]: 85
Luego, dirigir el cursor hacia la izquierda y teclear 60
Specify next point or [Undo/Close]: 60
Specify next point or [Undo/Close]:
EJEMPLO 3
En el siguiente ejemplo dibujaremos lneas verticales y
horizontales, utilizando coordenadas relativas cartesianas,
es decir, se dibujaran lneas teniendo en cuenta el ltimo
punto de la lnea anterior.
Hay que tener en cuenta que las distancias pueden ser
positivas (hacia arriba o hacia la derecha) y negativas
(hacia abajo o hacia la izquierda).
UNIVERSIDAD NACIONAL DEL CALLAO
FACULTAD DE INGENIERIA ELECTRICA Y ELECTRONICA
ESCUELA DE INGENIERIA ELECTRONICA
EJERCICIO RESUELTO
Ingrese 144 (radio del crculo) y presione Enter. 10. Trazamos el crculo de radio 132 concntrico con el
arco de radio 144.
Ingrese C y presionamos Enter.
Movemos el mouse sobre el arco de radio 144, se
visualizara su centro, movemos el mouse y sobre este
punto hacemos Clic.
12. De manera similar al paso anterior trazamos el crculo Movemos el mouse verticalmente hasta visualizar el
de la parte inferior. smbolo de interseccin y hacemos Clic.
EJERCICIOS PROPUESTOS
UNIVERSIDAD NACIONAL DEL CALLAO
FACULTAD DE INGENIERIA ELECTRICA Y ELECTRONICA
ESCUELA DE INGENIERIA ELECTRONICA