Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Link
SPECIFICATIONS DISASSEMBLY SCHEMATIC DIAGRAMS
2008H0500-1
DSC-W120/W125_L2 2008.8
9-852-264-34 Sony EMCS Co. Published by Kohda TEC
SPECIFICATIONS
DSC-W120/W125_L2
2
Ver. 1.2 2008.05
The changed portions from
Ver. 1.1 are shown in blue.
Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J : Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
TH : Thai model
DSC-W120/W125_L2
3
ENGLISH JAPANESE
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY CHECK-OUT
1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
2. Check the interboard wiring to ensure that no wires are
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
: LEAD FREE MARK
transistors, that were installed during a previous repair. Point
Unleaded solder has the following characteristics.
them out to the customer and recommend their replacement. Unleaded solder melts at a temperature about 40C higher than
4. Look for parts which, through functioning, show obvious signs ordinary solder.
of deterioration. Point them out to the customer and Ordinary soldering irons can be used but the iron tip has to be
recommend their replacement. applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to
6. Flexible Circuit Board Repairing about 350C.
Keep the temperature of the soldering iron around 270C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
Strong viscosity
Do not touch the soldering iron on the same conductor of the
Unleaded solder is more viscous (sticky, less prone to flow) than
circuit board (within 3 times). ordinary solder so use caution not to let solder bridges occur such
Be careful not to apply force on the conductor when soldering as on IC pins, etc.
or unsoldering. Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
DSC-W120/W125_L2
4
ENGLISH JAPANESE
1. 6.
270
3
2. 7.
Lead Free
0
3.
40
4. 350
5. IC
DSC-W120/W125_L2
5
1. SERVICE NOTE ENGLISH JAPANESE
LCD screen
Blinks at 3.2 Hz
C 32 00
DSC-W120/W125_L2
1-1
ENGLISH JAPANESE
Initializes the setting to the default setting. Even if you execute this function, the images
stored in the internal memory are retained.
1 Select [Initialize] with v/V on the control button, then press z.
The message Reset to default settings appears.
2 Select [OK] with v, then press z.
The settings are reset to the default setting.
To cancel initializing
Select [Cancel] in step 2, then press z.
DSC-W120/W125_L2
1-2
ENGLISH JAPANESE
Note 1: When replacing the SY-189 board, erase the data in internal memory of the board before replacement.
Note 2: When replacing the SY-189 board, execute formatting and initialize the internal memory after replacement.
To cancel copying
Select [Cancel] in step 3, then press z.
Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.
You cannot select images to copy.
The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the Memory Stick Duo after copying, then format the internal memory
([Format] in [Internal Memory Tool]).
A new folder is created on the Memory Stick Duo and all the data will be copied to it. You cannot
choose a specific folder and copy images to it.
The (Print order) marks on the images are not copied.
Format
To cancel formatting
Select [Cancel] in step 2, then press z.
DSC-W120/W125_L2
1-3
ENGLISH JAPANESE
4) Upon completion of the setting change, the following message will be displayed.
5) Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).
6) Write the data read out into the PC to the internal memory of the camera.
7) Disconnect the PC from the camera, and turn off the camera.
Note: By turning off the camera, the write enable setting is reset.
DSC-W120/W125_L2
1-4
1. SERVICE NOTE ENGLISH JAPANESE
1-1. SY-189
ADJDESTINATION DATA WRITE
USBNo.
1IDUSB Serial No.
IDID
ADJUSB SERIAL No. INPUT
1-2.
1-2-1. 1-2-2.
LCD
L C D 43.2Hz5
LCD
C : 3 2 : 00
3.2Hz
C 32 00
C 1 -2 -3 .
E 13
32
DSC-W120/W125_L2
1-5
Ver. 1.1 2008.02
ENGLISH JAPANESE
1-2-3.
C 1 3 0 1
C 3 2 0 1
E 6 1 0 0
SY-189CN403 rg
ICSY-189IC401
E 6 1 1 0
SY-189CN403 wk
IC
SY-189IC401
E 6 2 0 2 IC ICSY-189IC503
E 6 2 1 0 IC ICSY-189IC503
E 6 2 1 1 PITCH PITCHSY-189
CN403 qdqg
PITCH/YAWSY-189SE502
E 6 2 1 2 YAW YAWSY-189
CN403 qhqk
PITCH/YAWSY-189SE501
E 6 2 2 0 SY-189CN403
qa
E 9 1 0 1 Note
E 9 2 0 0
Note1-3.
DSC-W120/W125_L2
1-6
ENGLISH JAPANESE
1-3.
E9101
/
1-4.
Note1 SY-189
Note2 SY-189
DSC-W120/W125_L2
1-7
ENGLISH JAPANESE
1-5.
PC
WriteEnableTool.exe
1) PCSony Seus USB Driver
2) SeusEX
3) [Activate Write Enable Mode]
4)
5) PC
6) PC
7) PCOFF
OFF
DSC-W120/W125_L2
1-8E
2. DISASSEMBLY
Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt
Do not insert the cable insufficiently nor crookedly. which comes off at the point.
(Be careful or some
When remove a connector, dont pull at wire of connector. It is possible that a wire is snapped. pieces of gilt may be left inside)
The charging capacitor (C901) is charged up to the maximum Note: High-voltage cautions
300 V potential.
There is a danger of electric shock by this high voltage when the Discharging the Capacitor
capacitor is handled by hand. The electric shock is caused by Short-circuit between two points
the charged voltage which is kept without discharging when the with the short jig about 10 seconds.
main power of the unit is simply turned off. Therefore, the
R:1 k/1 W
remaining voltage must be discharged as described below. (Part code: 1-215-869-11)
C901
DSC-W120/W125_L2
2-1
2-1. IDENTIFYING PARTS
Cabinet (Rear)
Cabinet (Upper)
AF-112 Board
ST-180 Board
BT Holder Section
MC-189 Flexible Board
ST-188 Flexible Board
SY-189 Board
LCD
LCD Frame
SW-520 Board
SW-533 Flexible Board
Cabinet (Front)
Lens Block
CCD Block (CD-719 Flexible Board)
- DISASSEMBLY FLOW -
DSC-W120/W125_L2
2-2
HELP
2-2. DISASSEMBLY
EXPLODED VIEW HARDWARE LIST
2-2-1. LCD SECTION
Follow the disassembly in the numerical order given.
1 Cabinet (Rear) (1-1 to 1-5)
2 LCD (2-1 to 2-17)
1 Cabinet (Rear)
1-4 (Boss)
HELP 1
1-1 (#20)
2-11
HELP 3
2-7
2-2 (#20) (Claw) 2LCD
2-12 2-14
HELP 2 (Claw)
2-13
(Claw)
2-8
2-5 (#20)
ST-180 Board
C901
DSC-W120/W125_L2
2-3
2-2-2. FRONT SECTION
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 Cabinet (Front) (1-1 to 1-3)
2 Lens Block (2-1 to 2-6)
2-3 HELP 4
BT Holder Section
(See Page 2-5)
1 Cabinet (Front)
2-4
HELP 4
1-3 (Claw)
2-2
2-5
2-1 (#20)
1-1 (Claw)
1-2 (Claw)
DSC-W120/W125_L2
2-4
2-2-3. BT HOLDER SECTION
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 Cabinet (Upper) Block (1-1 to 1-4)
2 SY-189 Board (2-1 to 2-5)
2SY-189 Board
1 Cabinet (Upper) Block
HELP 6 1-4 1-1
1-2 2-4
HELP 7 (#20) HELP 9
2-3 (Claw)
DSC-W120/W125_L2
2-5
2-3. PRECAUTIONS WHEN HOLDING THE LENS BLOCK
OVF
Lens Flexible Board
Lens Barrel
Lens Barrier
Very weak
Optical Stepping Motor
Very weak Zoom Motor
Focus Lens
DSC-W120/W125_L2
2-6
2-4. BARRIER ASSY REPLACING METHOD
Removal
1 Turn on the power switch and extend the lens.
2 Detach the battery.
3 Pour a solvent such as alcohol from two places A to the tweezers or a needle shown below into a gap of Ornamental Ring A.
4 Remove while turning the Ornamental Ring A right and left.
Ornamental Ring A
A Tweezers
Solvent
Installation
1 Affix two Barrier Tapes to Barrier Assy.
Note: The tape must not be wrinkled.
2 With four claws fitted in position, install the Barrier Assy.
DSC-W120/W125_L2
2-7
2-5. LENS MOTOR REPLACING METHOD
Replace the parts if the following events appear when the power switch is turned on.
1 "Turn off and on the power" is displayed without performing the zoom operation.
Replace Zoom Gear Block if a damage of lens barrel due to a drop of camera is not found.
(See "2-5-1. Zoom Gear Block Replacing Method")
Replace Lens Block if such replacement does not improve the failure.
2 "Turn off and on the power" is displayed after the "lens zooming in and out" operation over its full stroke was repeated
3 times.
Replace Optical Stepping Motor. (See "2-5-2. Optical Stepping Motor Replacing Method")
Replace Lens Block if such replacement does not improve the failure.
Removal
1 Remove one screw.
2 Remove Zoom Gear Block upward.
3 Remove Naruto Gear (S).
4 Disengage two claws A and B in this order to remove FG Plate Spring.
Note: The FG Plate Spring cannot be reused.
5 Remove two sensors on the lens flexible board.
6 Break two solders, and remove the lens flexible board.
1 Screw
6 Solders
5 Sensors
Claw A
Mold 1 Solders
Bosses
2 Sensors Rear Side
Claw B
Removal
1 Disengage the lens flexible board from the claw.
2 Disconnect the connector of the lens flexible board.
3 Remove Zoom Gear Block by referring to the removal 1 to 3 in "2-5-1. Zoom Gear Block Replacing Method".
4 Remove three screws.
5 Remove the lens rear block.
4 Screws
2 Connector
5 Lens Rear Block
1 Claw
6 Screw
7 Optical Stepping Motor
8 Solders
DSC-W120/W125_L2
2-9
Installation
1 Install the lens flexible board with four solders.
2 Referring to the following figure, check each part state of lens rear block.
3 Install Optical Stepping Motor.
4 Tighten one screw.
* Tightening torque = 0.049 0.01N m (0.5 0.1kgf cm)
1 Solders
Lens Rear Block
5 Rotate the gear of lens barrel in arrow direction to extend the lens.
6 Check the inside of lens barrel and the lens for dust or stain, and then install the lens rear block.
7 Tighten three screws.
* Tightening torque = 0.049 0.01N m (0.5 0.1kgf cm)
8 Install Zoom Gear Block by referring to the installation 4 to 6 in "2-5-1. Zoom Gear Block Replacing Method".
9 Connect the connector of lens flexible board.
0 Assemble the lens flexible board with the mold of Lens Block.
qa Engage the lens flexible board with the claw.
7 Screw 9 Connector
qa Claw
6 Lens Rear Block
0 Molds
DSC-W120/W125_L2
2-10
2-5-3. FINAL INSPECTION (NO FAULT IN ACTUAL MOTION/ACTUAL SCREEN)
1 Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
2 Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
3 Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
4 Appearance condition
Scratches or stains must not be noticeable, except that the customer permits them.
5 Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.
Upward
Lens at WIDE end
Upper oblique 45
Lower oblique 45
Lens at TELE end
Downward
DSC-W120/W125_L2
2-11E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
HELP 1: LCD Window Adhesive Sheet Kit HELP 3: LCD Insulating Sheet
LCD Window Adhesive Sheet Kit must use only - Front Side -
the part of LCD window edge. LCD Insulating Sheet
Please discard other parts.
Discard parts
Hole
Paste parts
- Rear Side -
LCD Insulating Sheet
Hole
LCD Window Adhesive Sheet Kit
DSC-W120/W125_L2
HELP
HELP 4: Tape (AF)/Capacitor Protection Sheet HELP 5: BT Terminal Harness
BT Holder
Tape (AF)
BT902 (White)
BT903 (Black)
BT901 (Red)
Tape (AF)
SY-189 Board
BT Terminal Harness
BT Holder Mold
Capacitor Protection Sheet
DSC-W120/W125_L2
HELP
HELP 6: Sheets and Harness of ST-180 Board
- Top View -
ST Insulating Sheet Harness (HN-062) (Gray)
Harness (HN-061) (Yellow)
ST-180 Board Harness (HN-059) (Pink)
Harness (HN-060) (Blue)
- Bottom View -
Speaker Harness (Black) Harness
Speaker Harness (Red)
ST-180 Board
Harness (HN-060) (Blue)
- Front View -
Lithium Insulating Sheet
ST-180 Board
- Rear View -
ST Insulating Sheet
ST-180 Board
AF-112 Board
DSC-W120/W125_L2
HELP
HELP 7: Installation Method of Battery Terminal Board
1 Insert the battery terminal board into a slit in the BT holder to install.
* The battery terminal board is attached with the notch for installation.
BT holder
Notch
Battery terminal
Battery terminal board board
DSC-W120/W125_L2
HELP
HELP 8: Lens Flexible Board/CD-719 Flexible Board
DSC-W120/W125_L2
HELP
3. BLOCK DIAGRAMS
Link
DSC-W120/W125_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
LENS BLOCK CD-719 FLEXIBLE BOARD SY-189 BOARD (1/2) LCD901 (1/2)
LCD MODULE
G3 - G1, H3 - H1, J1
36 - 30
CCD_OUT
17 32 10 BUFFER 14 H10 CA_AD00 - CA_AD13 LCD_D1 - LCD_D7 D0 - D6
IC003 (1/10)
7M CCD 1
IMAGER PWR_SAVE CA_HD
29 - 27
LCD_CK, LCD_HD, LCD_VD MCK, Hsync, Vsync
A3, B1
CCD SIGNAL CA_FD 2.5INCH
AF22
PROCESS, COLOR
SHUTTER ZOOM FOCUS IRIS TIMING GEN_TG_CLK XCS_ PANEL XCS LCD
A4 AF18 U19 4
5, 6, 8, 9
H1A, H2A, H1B, H2B IC203 XDD_SYS_RST XRST
(1/10) 3
M M M M X201
IC202
(1/2)
5, 6
33.75MHz 1 CPU IC_203_2_SO, XIC_203_2_SCK SI, XSCK
RG GEAR_ON
19 36 K4 2 CLOCK 3 Y13 (4/10, 5/10) DETECT_V_OUT TESTOUT
GENERATOR GEN_SYS_CLK P19 37
5 Y12
1, 3, 6 - 12,
FOCUS
14 - 16
V5A, V5B, V6 - V10
RESET
C2, C3, B3
E18, B23
F3, E3
Q301 E7
XCS_AUDIO CN707 CN002
V8 E4 (1/2)
VSUB_CONT_PRE, (1/2)
R7, AF25
VSUB_CONT_POST MIC_SIG MIC_SIG MIC901
Q302 IC_203_AUIN B6 12 20 MICROPHONE
AF8 E6
BLOCK
IC401 IC603
XLENS_DRIVER_PS
27, 26
A5, A2
SP SP SP901
LENS DRIVE D4 H11
5, 6
IC_203_AUOUT
AE8 E5 AUDIO AMP SPEAKER
(2/10) (7/10)
CN403
D2, B1
Y18, Y17
D3, F1
ND() ND_ IRIS MOTOR IRIS_M_DIR_2B, IRIS_M_BRK_2B
6, 5
B4, B5
Z_DC_MOTOR() ZOOM_A, ZOOM_A- ZM_DIR_A, ZM_EN_A, ZM_BRK_B T8 4
MOTOR V_LINE_OUT V_OUT
DRIVER 3 VIDEO AMP 5 36 20
(7/10)
IC_203_YOUT HD Y HD Y CN001
SHUTTER
G1, E4
F4, F3
R8, AE25
SHUTTER() SHUTTER_ MSHUT_DIR, MSHUT_EN AB13 34 24 (1/2)
4-1
MOTOR IC_203_PBOUT HD Pb HD Pb
DRIVER AF12 7 4 MULTI
IC_203_PROUT HD Pr HD Pr CONNECTOR
AC12 9 2
F_PI_SENS_OUT FC_SENS
45 Y10
ZOOM FPI_GND XFC_RST_LED
ZOOM 43 M8
FG RESET
SENSOR
Z_PI_SENS_OUT
10, 12
ZM_SENS_1ST
Y1, AA1
15, 17
28 AD26 USB_DP, USB_DM USB_DP, USB_DM
Y11, W11
36, 34
2 - 5, 7, 8
A13 - A15,
DUO
B13 - B15
OPTICAL IMAGE
OIS TEMP THERM TZ_HALL_TEMP
STABILIZER SENSOR
11 AF3
SE501
G6, J8, J9, J7 B10, D10
25 - 22
HALL YAW_HALL_
D5, D6
24, 25
A : VIDEO SIGNAL
IC_203_0_SO, IC_203_0_SI, XIC_203_0_SCK OVERALL (2/2)
(PAGE 3-2) A : AUDIO SIGNAL
CLK_IC_503 A : VIDEO/AUDIO SIGNAL
A3 W13
XCS_IC_503
A5 U8
XIC_203_IC_503_RST
A6 H10
05
DSC-W120/W125_L2
3-1
3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
27 - 32
23, 25
ACV_UNREG ACV_UNREG
ST_UNREG
MS_VCC
CAM_12.5V
CAM_-7.5V
USB_3.2V
M_5.0V
D_3.1V IC001
Q001, XACV_DET XACV_DET
DC/DC Q002 20 19
A_3.1V CN001
CONVERTER D001 (2/2)
DDR_1.8V
21 - 26
(9/10) MULTI
17, 21
BATT_UNREG CHARGE_V
D_1.85V CONNECTOR
D_1.5V
D_1.25V
BL_H
SW-533
FLEXIBLE
SW-520 BOARD BOARD K7 D002
X001 XACV_IN
CN001 CN706 XPWR_ON XPWR_ON K8
S012 D7 32.768kHz
XDIRECT_PB XDIRECT_PB XDIRECT_PB K6 XAV_JACK_IN XACC_IN XACC_IN
5 6 D9 G9 33 26
UART Rx,
D26, G19
19, 12
IC_203_1_UI, IC_203_1_UO UART_Rx, UART_Tx
15, 9
UART Tx
S001 - S009,
S011 XMS_IN
FUNCTION
KEY_AD1,
KEY_AD2
KEY_AD1,
KEY_AD2 2 D10
10, 9
1, 2
LCD901 (2/2) KEY OVERALL (1/2) USB_VBUS
LCD MODULE E7
(PAGE 3-1) XPWR_OFF
S010 MODE_DIAL1, MODE_DIAL1, C10 G8
BACKLIGHT
MODE 7, 6 MODE_DIAL2 MODE_DIAL2
4, 5
DIAL XIC_203_RST_REQ
BL_H D6 W12
XDD_SYS_RST
BL_L BL_L BL_L C9 AB18
3 8 E10
BATTERY
XCS_DD TERMINAL
C5 A23
C6 - C8
BATT_UNREG
ST-188 XAF_LED +
C4 IC_203_0_SO,
FLEXIBLE IC_203_0_SI, XCS_IC_201,
ST-180 BOARD (2/2) S102 CN002 BOARD (2/2) CN707 XIC_203_0_SCK XIC_203_1_SCK, BT902
IC_203_1_SO, BATT_SIG
XDD_SYS_RST
D201
SELF-TIMER/
XAF_LED
23
XAF_LED
9
XAF_LED 1 IC203
OVERALL (1/2) (2/2)
SMILE SHUTTER/ IC_203_0_SO, IC_203_0_SI, XIC_203_0_SCK
AF ILLUMINATOR (PAGE 3-1) CPU
XAE_LOCK_SW XAE_LOCK_SW
S101 13 19 N19
(SHUTTER) XSHUT_SW XSHUT_SW
15 17 R19
D102
FLASH CHARGE/ XSTRB_LED XSTRB_LED
17 15 W8
RECORD
STRB_CHG STRB_CHG
15 IC001 10 8 24 V2
XSTRB_FULL XSTRB_FULL
XE_L 9 12 20 H9
1, 2
STRB_CHG_CONT STB_CHG_CNT
FLASH 6 11 21 H15
CONTROL,
Q001 CHARGE STRB_ON STRB_ON1
FLASH 7 CONTROL 4 9 23 Y16
DRIVE (1/2)
05
05
DSC-W120/W125_L2
3-2
3-3. POWER BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
27 - 32
23, 25
ACV_UNREG ACV_UNREG
IC001
Q001, Q002 DC/DC CONVERTER (9/10)
XACV_DET XACV_DET
19 20
CN001 G6 UNREG
D001 CN708
MULTI D002
CONNECTOR MS_VCC MEMORY
G3 MS_PWR_ON MS_PWR_OUT F3 9 STICK
21 - 26
17, 21
DDC5_PSW H1
L001
XPOWER_ON XPOWER_ON DDC5_LX_1 J3
7 11
DDC5_LX_2 K3
ST_UNREG
D006
M_5.0V
DDC5_VO_1 J2 B+ SWITCH
DDC5_VO_2 K2 Q003
LDO3P1U_IN H4
USB_3.2V
LDO3P1U_OUT J5
XACV_IN
L002
BATTERY DDC12_LX_1 J9
TERMINAL IC201 CAM_12.5V
DDC12_LX_2 K9
BT901 BATTERY D007
BATT_UNREG
+ AUTHENTICATION
(8/10)
D DDC12_VFB H8
Q006, Q007
BT902 IC_203_1_SI POWER (2/2)
BATT_SIG P144_SOA0 D5 (PAGE 3-4) DDC12_PWR_IN1 G8
S E4 TXRX IC_203_1_SO
P143_SIA0 C5 DDC12_PWR_IN2 G7
XIC_203_1_SCK
BT903 P142_XSCKA0 B5 D008
XCS_IC_201 CAM_-7.5V
P120_INTP0 B1 H10 DDCM7P5_PWR DDCM7P5_LX J10
DDCM7P5_VFB F8
B2 XRESET L006
D_3.1V A_3.1V
C2 DDC2P9_PWR_1 DDC2P9_VO_1 F1
D_3.1V D_3.1V
B1 DDC2P9_PWR_2 DDC2P9_VO_2 F2
DDC2P9_VFB G1
L008
D_1.25V
A XDD_SYS_RST B3 DDC1P2_PWR DDC1P2_LX A4
DDC1P2_VFB B2
POWER (2/2)
(PAGE 3-4) L009 D_1.85V
B8 DDC1P8_PWR DDC1P8_LX A8
DDC1P8_VFB B6 E
POWER (2/2)
D_1.5V (PAGE 3-4)
LDO1P5_OUT A6
DDR_1.8V
LDO1P8_OUT A7
LDO3P1E_OUT F5
R008 R005 D004
RTCBAT H5
MS_PWR_ON MS_PWR_ON R006 VL_3V
IC_203_0_SI
C7 SO
IC_203_0_SO
C6 SI
B XIC_203_0_SCK
C8 SCK L004 F003
XCS_DD DDCBL_LX F10
POWER (2/2) C5 XCE
XIC_203_RST_REQ
(PAGE 3-4) D6 XRESET_REQ
XPWR_OFF D009
C10 XPWR_OFF
BATT_SENS BL_H
F6 UNREG_MON DDCBL_VO F9
BL_L
DDCBL_VL E10
C XPWR_ON
XDIRECT_PB
D7 XPWR_ON1
D9 XPWR_ON3
POWER (2/2)
Q008
(PAGE 3-4) 1.85V
XDD_SYS_RST DISCHARGE
XSYS_RESET C9
D_3.1V
XDD_SYS_RST
05
DSC-W120/W125_L2
3-3
3-4. POWER BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
LCD901
SY-189 BOARD (2/2) LCD MODULE
CN704
M_5.0V L702 VDDD2IN
15
D_3.1V L701
VDD1A 2.5INCH
8
VDD1D COLOR
IC507 9
XDD_SYS_RST XRST LCD
2.8V REG 3
(3/10) IC506
A_3.1V PITCH/YAW SW-520 BOARD
4 VDD VOUT 1 SENSOR AMP SW-533
CE (3/10) FLEXIBLE
CN706 CN001 BACKLIGHT
3 BOARD
BL_H BL_H BL_H
SE502 10 1
BL_L BL_L BL_L
PITCH 8 3
D_1.85V SENSOR S012
IC503 XDIRECT_PB
6 5
OPTICAL SE501
D_3.1V IMAGE YAW
M_5.0V STABILIZATION
DRIVE
SENSOR C ST-188
D_1.5V
(3/10) POWER (1/2) FLEXIBLE ST-180 BOARD
(PAGE 3-3) CN707 BOARD CN002 S102
ST_UNREG
A XDD_SYS_RST
A7 RESET_N
XPWR_ON
18 14 POWER
XIC_203_IC_503_RST
POWER (1/2) A6 XDL
D_1.25V (PAGE 3-3)
D101
24, 25
D_3.1V
7, 8
XDD_SYS_RST (AE/AF LOCK)
CAM_12.5V
CAM_-7.5V
D102 AF-112 BOARD
FLASH CHARGE D201
RECORD
SELF-TIMER/
SMILE SHUTTER/
A_3.1V D_1.85V D103 AF ILLUMINATOR
D_3.1V D_3.1V D_3.1V (POWER)
D_3.1V
BL_H M_5.0V M_5.0V
BL_L A_3.1V A_3.1V
E M_5.0V
T001
IC603 Q701, Q702
L001 D001
29 - 31
POWER (1/2) ST_UNREG ST_UNREG FLASH
1-3
AU_AVCC AUDIO AMP
(PAGE 3-3) 4 VDD VOUT 1 UNIT
(7/10) M_5.0V ST_5V
3 CE 22 10
H10 GPE_09 R601
IC602 STRB_UNREG_ON
IC601 AB18 XRESET
2.8V REG VIDEO AMP IC001
(7/10) D601 (7/10) FLASH CONTROL, BT900
A_3.1V CHARGE CONTROL
R780 LITHIUM
D_1.85V D709 (1/2)
BATTERY
R253 (ACCESS)
DDR_1.8V VL_3V VL_3V VL_3V
2 30
L241
VL_3V D_3.1V
USB_3.2V R254
CD-719 FLEXIBLE
D_1.25V BOARD
D_3.1V IC202 CN301
DDR_1.8V L301
D_1.85V CLOCK CAM_12.5V CAM_12.5V_CD
D_1.85V FB282 GENERATOR 12
IC203 R205 IC003
(8/10)
CPU 7M
FB283 (4/10 - 6/10) CAM_-7.5V L302 CAM_-7.5V_CD CCD IMAGER
2
USB_3.2V
FB307 FB313
Q303
-7.5V IC309
DISCHARGE
BUFFER
(1/10)
FB311
IC_203_0_SI
A24 SIO0_RXD D_3.1V FB310
IC_203_0_SO
H17 SIO0_TXD
XIC_203_0_SCK IC310
G17 SIO0_SCK IC304 LENS BLOCK
B XCS_DD
A23 SIO0_SCS
3 3.3V REG
CCD SIGNAL
XIC_203_RST_REQ CE (1/10)
W12 XRESET_REQ M_5.0V PROCESS, Q401 CN403
POWER (1/2) 4 VDD VOUT 1 R402 ZOOM
XPWR_OFF TIMING GENERATOR Z_PI_SENS_Vcc
(PAGE 3-3) G8 GPE_00 (1/10) SENSOR SWITCH 26 RESET
MS_PWR_ON SENSOR
T7 GPE_15
BATT_SENS
XZM_RST_LED
AE7 ADC0_IN6 D_3.1V
6 Vin Vout 4 R412 Z_BOXPI-1_SENS_Vcc
37 ZOOM
1 Vcont Z_BOXPI-2_SENS_Vcc FG
XACV_IN 35
K8 GPE_05 R411
IC308
D IC_203_1_SI
G18 SIO1_RXD 2.8V REG R401 F_PI_SENS_Vcc FOCUS
IC_203_1_SO (1/10) 44 RESET
POWER (1/2) B24 SIO1_TXD
XIC_203_1_SCK XDD_SYS_RST SENSOR
(PAGE 3-3) H18 SIO1_SCK C1 RESET
XCS_IC_201
W20 GPS_04
D_3.1V
STRB_UNREG_ON M_5.0V
GPS_13 W7 IC401
A_3.1V
LENS DRIVE
(2/10)
XZM_RST_LED
GPE_03 J8
05
DSC-W120/W125_L2
3-4E
Ver. 1.1 2008.02 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
LENS BLOCK
SW-520 BOARD
CN0011
10
10 1
1
31
39
IC003
(Not supplied)
LCD901
LCD MODULE
31 1 31 1
CN002 CN707
30 2 30 2
2
2.5INCH
COLOR BACKLIGHT
CN301
LCD
10
CN706
Black
Red
1
38
39
10 1
39
SP901
38
SPEAKER
1
2
CN704
CN403
CN708 IC203
(Not supplied)
1
2
FLASH UNIT
44
45
MIC901
MICROPHONE
BLOCK 12
11 2 38
1
CN709 39
LEVEL3 LEVEL3
C901
SY-189 BOARD SY-189 BOARD
LOCK
CHARGING CAPACITOR
(SIDE B) (SIDE A)
HARNESS (HN-060) (Blue) IC001
CN001
HARNESS (HN-061) (Yellow)
HARNESS (HN-062) (Gray)
MULTI CONNECTOR
1 39
AF-112 BOARD
28 26 2 27
25 1
DSC-W120/W125_L2
4-1 FRAME
4-2. SCHEMATIC DIAGRAMS
Link
SW-520 BOARD
CD-719 FLEXIBLE BOARD (CCD IMAGER) (CONTROL SWITCH)
MC-189 FLEXIBLE BOARD
ST-180 BOARD (1/2) (FLASH DRIVE) (MULIT CONNECTOR)
ST-188 FLEXIBLE BOARD
ST-180 BOARD (2/2) (CONTROL SWITCH) (SY-ST CONNECTION)
DSC-W120/W125_L2
4-2. SCHEMATIC DIAGRAMS ENGLISH JAPANESE
Magenta
White
curve B, unless otherwise noted. Cyan
Signal name Green
Red
Blue
XEDIT EDIT PB/XREC PB/REC
2: non flammable resistor
5: fusible resistor
C: panel designation
A: B+ Line
B: B Line A B A=B B A
J : IN/OUT direction of (+,) B LINE. Fig. a (Video output terminal output waveform)
C: adjustment for repair.
(Measuring conditions voltage and waveform)
Electronic beam
Voltages and waveforms are measured between the
scanning frame
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values CRT picture frame
and reference waveforms.
(VOM of DC 10 M input impedance is used)
Voltage values change depending upon input
impedance of VOM used.)
Fig.b (Picture on monitor TV)
Precautions for Replacement of Imager
If the imager has been replaced, carry out all the adjustments When indicating parts by reference number, please
for the camera section. include the board name.
As the imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC. The components identified by mark 0 or dotted line with
In addition, ensure that the receiver is not covered with mark 0 are critical for safety.
dusts nor exposed to strong light. Replace only with part number specified.
DSC-W120/W125_L2
4-2
4-2. SCHEMATIC DIAGRAMS ENGLISH JAPANESE
(JAPANESE)
1.
50V
FppF
110W Pattern box PTB-450 For PTB-450:
k1000M1000k J-6082-200-A J-6020-250-A
or
Small pattern box For PTB-1450:
PTB-1450 J-6082-559-A
J-6082-557-A
L = 24 m (PTB-450)
L = 11 cm (PTB-1450)
C 541 L 452
22U 10UH
TA A 2520
L
mm
ICXX
2. ab
H
B
XEDITEDITPB/XRECPB/REC
2
1
C
AB
BB A B A=B B A
JB
a
C
DC10M
b
00
MOS IC
DSC-W120/W125_L2
4-3
1 2 3 4 5 6 7 8
CAM_-7.5V_CD
VHLD
V7
V6
V4
V5B
V5A
V3B
V3A
A A
Note: IC003(CCD imager) and CD-719 flexible complete board are
not supplied, but there are included in CCD block assy.
11
10
12
6
7
5
9
Note: Voltages of IC003 can not be measured,
VHLD
V6
V7
V4
V5B
V5A
V3B
V3A
because this is mounted by the side of the lens.
13 N.C.
4
N.C.
V8 V2 V2
14
3
V8
V9 VST VST
15 IC003
2
V9
V10 ICX629EQP-13 V1 V1
16
1
CCD_OUT V10 7M CCD IMAGER
B H2A B
29 30 31 32
SY-189 17
CCD-OUT
(1/10) H1A
20 19 18
CN301 VH
VL
Page 4-5 RG
of Level 3 N.C.
N.C.
LND001
1 GND
C003 C009
WGND
LND002
CSUB
RSS3
2 CAM_-7.5V_CD 0.1u 0.1u
GND
SUB
H2B
N.C.
H1B
16V 16V
LND003
3 GND B B
RG
LND004 21 22 23 24 25 26 27 28
4 GND
LND005 H1A
5 H1A
LND006 H1B
6 H1B C005
0.1u
LND007 7 GND 10V
LND008 H2B B
8 H2B
C H2A
C
LND009
9 H2A
LND010
10 GND
LND011 11 GND
CAM_12.5V_CD
LND012
12 CAM_12.5V_CD
LND013
13 GND
LND014 14 GND
LND015 V3B
15 V3B
LND016 V4
16 V4
LND017 V5A
17 V5A
LND018 V5B
18 V5B
LND019 V6
19 V6
SUB
LND020 V7
20 V7
D LND021 21 V3A
V3A
CSUB D
LND022 V2
22 V2
LND023 VHLD
23 VHLD
LND024 VST
24 VST
LND025 V1
25 V1
LND026 V8
26 V8
LND027 V9
27 V9
LND028 V10
28 V10
LND029
29 GND
LND030 30 GND
LND031
31 GND
LND032 32 CCD_OUT
LND033 GND
33
E E
LND034
34 GND
LND035 35 GND
LND036
36 RG
LND037
37 GND
LND038
38 VSUB_CONT
LND039 39 VSUB
LND040 STATIC_GND
05
DSC-W120/W125_L2
4-4 CD-719
Schematic diagrams of the SY-189 board are not shown.
Pages from 4-5 to 4-14 are not shown.
DSC-W120/W125_L2
Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
1 2 3 4 5 6 7 8
AF-112
LND033 LND201, LND202
Through the
XAF_LED
Harness
A (HN-061, HN-062) A
D_3.1V
CN002 Page 4-16
31P of Level 2
L001 LND034
ST_UNREG 1 2.2uH
ST_UNREG 2 2 3
ST_UNREG 3 D001
R005 LND038
4700 C006 CRF02(TE85R)
NC 4 C002 220p
22u C 50V B 1 4 +
REG_GND 5 6.3V LND035
HARNESS (HN-059)
REG_GND 6 T001 XE_H
(Pink)
RB520S-40TE61
REG_GND 7
STRB_CHG 8 R003
D003
STRB_ON 9 1M LND031
C008
B B
6.3V
4.7u
ST_5V
B
10 TRIGGER
C901
STRB_CHG_CONT 11 315V
62uF LND032 FLASH
XSTRB_FULL 12 UNIT
CHARGING TRIGGER_GND
XAE_LOCK_SW 13 XAE_LOCK_SW 3.8 CAPACITOR
HARNESS (HN-060)
XPWR_ON 14 XPWR_ON 17 16 15 14 13
(Blue)
XSHUT_SW 15 XSHUT_SW
HGND
N.C
VBATT
N.C
N.C
XAE_LOCK_LED 16 XAE_LOCK_LED XE_L
XPWR_LED 18 XPWR_LED
3.8 -
PGND
10 11 12
REG_GND REG_GND1 LND039
1
19 SW LND037
MIC_SIG PGND TRIGGER_GND
2
20 MIC_SIG SW
5 IC001 0 C005
REG_GND(MIC_GND) MIC_GND CHG
3
21 VCC TPS65552RGTR 250V
0 3.1
REG_GND FLASH CONTROL, XFULL 0.047u
9
22
C F_ON CHARGE CONTROL C
XAF_LED 23
C003 C001
D_3.1V 24 XX 1u B
G_IGBT
I_PEAK
D_3.1V 25 D_3.1V Q001
N.C
N.C
TIG030TS-S-TL-E
SP- 26 SP- FLASH
SP+ 27 SP+ 5 6 7 8 DRIVE
5 1 270
REG_GND 28 REG_GND1 CL001 0 0
6 2
NC 29
7 3
VL_3V 30 VL_3V CL002
8 4
NC 31 C004
XX R001 0
1M R002
100
ST-188
FLEXIBLE
D LND041-LND071 D
Page 4-18
of Level 2
Note: C901, harness (HN-059) and harness (HN-060)
are not included in ST-180 complete board.
E E
ST-180 BOARD (1/2)
FLASH DRIVE
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
F F
05
DSC-W120/W125_L2
4-15 ST-180 (1/2)
Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
1 2 3 4 1 2 3 4
Note: LCD901 is not included in
SW-520 complete board.
LCD901(2/2) LCD MODULE
12
LND001
XAE_LOCK_LED
D101 BL_H
A CL-196SYG-CD-T (AE/AF LOCK)
A A BL_L
10 KEY_AD1 A
XSTRB_LED 9 KEY_AD2
BACKLIGHT LND002
D102
8 REG_GND
LNJ426W830S0 (FLASH CHARGE/RECORD)
7 MODE_DIAL1
4 S008 3 6 MODE_DIAL2
XPWR_LED 2 S003 1
D103
1
3
5
7
CL-196SYG-CD-T (POWER) 5 XDIRECT_PB
RB001
2200
D_3.1V
2 1 4 NC
4 3
W (ZOOM) T
2
4
6
8
LND107 3 BL_L
11
S012 CN001
S001 (SLIDESHOW)
B REG_GND1 REG_GND1 B B N B
MENU
SW-533
2 1
S102
4 3 4 3 FLEXIBLE
2 1 LND011-LND020
POWER
2 S006 Page 4-18
XPWR_ON 1
of Level 2
4 3 v
(DISP)
S101
(SHUTTER) 3 2
2
(1st) (2nd)
XAE_LOCK_SW SHIFT_ON 1005X4
VDR001
XX
1 4
2
4
6
8
RB002
2200
1 LND003
2 3
XSHUT_SW STATIC_GND
1
3
5
7
D001
XX
3
S005
LND104 2 1 1 7
COM SOFT SNAP RB003
V
8 2200
(SELF-TIMER) 2 LANDSCAPE 1 2
Note: BT900 (lithium battery), MIC901 and 4 3 COM 9 3 4
4
S002 LANDSCAPE 5 6
SP901 are not included in ST-180 complete board. 10 7 8
HOME TWILIGHT PORTRAIT
11
17 SCENE SELECTION
12
D D D MOVIE D
18 13
PROGRAM AUTO
14
1 2 3 4
E E
A ST-180 A
LND033, LND034
Through the 4 3
Harness LND201 XAF_LED 5 2
(HN-061, HN-062) 6 1
LND202 D_3.1V
D201
Page 4-15 CL-360S-TD4-X-TL
of Level 2 SELF-TIMER/
SMILE SHUTTER/
AF ILLUMINATOR
F SW-520 BOARD F
05
DSC-W120/W125_L2
4-16 ST-180 (2/2), AF-112, SW-520
1 2 3 4 5 6 7 8
39P
LND001 REG_GND
A LND002 AU_LINE_OUT A
LND003 A_GND
LND004 V_LINE_OUT
LND005 V_GND Note: CN001 (multi connector) is not supplied, but this is included
LND006 HD_Y in MC-189 flexible complete board.
LND007 XACC_IN
LND008 ACV_UNREG
LND009 ACV_UNREG
LND010 ACV_UNREG
LND011 ACV_UNREG
LND012 ACV_UNREG
LND013 ACV_UNREG
B B
LND014 BATT_UNREG
LND015 BATT_UNREG
LND016 BATT_UNREG
LND017 BATT_UNREG
SY-189 LND018 BATT_UNREG
(10/10)
LND019 BATT_UNREG
CN709
Page 4-14 LND020 XACV_DET
of Level 3
LND021 UART_Rx
LND022 USB_GND CN001
(MULTI CONNECTOR)
LND023 USB_DM
27
to AV/USB multi cable
LND024 N.C.
HD Pr
1
ACV_GND
LND025 USB_DP
HD Pb
3
ACV_GND
C LND026 USB_GND R004 C
USB_VBUS ACV_GND
5
LND027 USB_VBUS 1k
USB_GND
8
XPOWER_ON
7
LF001
LND028 UART_Tx 2 4
26 24 22 20 18 16 14 12 10
USB_DP
9
UART Tx
LND029 XPOWER_ON 1 3
25 23 21 19 17 15 13 11
USB_DM N.C.
LND030 REG_GND
USB_GND N.C.
LND031 HD_Pr
A_OUT_L UART Rx
LND032 REG_GND
A_GND CHARGE_V
LND033 HD_Pb
V_OUT XACV_DET
LND034 REG_GND
V_GND CHARGE_V
LND035 ACV_GND
HD Y ACV_UNREG
LND036 ACV_GND
XACC_IN ACV_UNREG
LND037 ACV_GND
28
LND038 ACV_GND
D D
LND039 ACV_GND
1P
E E
05
DSC-W120/W125_L2
4-17 MC-189
1 2 3 4
31P 1P
LND031 ST_UNREG ST_UNREG LND041
LND003 NC NC LND069
LND001 NC NC LND071
1P 31P
05
1 2 3 4
1P 10P
LND001 KEY_AD1 KEY_AD1 LND020
LND002 KEY_AD2 KEY_AD2 LND019
LND009 NC NC LND012
B
SW-533 FLEXIBLE BOARD B
SY-SW CONNECTION
(PRINTED WIRING BOARD is omitted.)
05
DSC-W120/W125_L2
4-18 ST-188, SW-533
4-3. PRINTED WIRING BOARDS
Link
AF-112 BOARD
DSC-W120/W125_L2
4-3. PRINTED WIRING BOARDS
(JAPANESE) 4 1
C
DSC-W120/W125_L2
4-19
CD-719 (2 layers)
: Uses unleaded solder.
LND003
LND004
LND005
LND006
LND007
LND008
LND009
LND010
LND011
LND012
LND013
LND014
LND015
LND016
LND017
LND018
LND019
LND020
LND021
LND022
LND024
LND023 917-DC
LND026
LND025
LND027
<IP>
LND028
LND029
LND030
LND031
LND032
LND033
LND034
LND035
LND036
LND037
LND038
39 LND039
12 5 C003
C009
13 4
IC003
1
C005
LND040
20 29
21 28
05 1-874-424- 11
DSC-W120/W125_L2
4-20 CD-719
Printed wiring board of the SY-189 board is not shown.
Pages from 4-21 is not shown.
DSC-W120/W125_L2
ST-180 (4 layers), AF-112 (2 layers)
: Uses unleaded solder.
MIC901
MICROPHONE
BLOCK
White
3 1 S101
2
3
LND101
Orange
S102
D003 C008
D103
LND102 C006
1
(POWER)
16
13
LND037
4 2 IC001
12
1
R005
17
HARNESS (HN-060) (Blue)
C901
9
4
CL002
R002
8
C001
CHARGING C003
8
+
R001
D101
C005
L001
CAPACITOR C002
Q001
LND038 LND034 LND033 R003 C004
HARNESS (HN-059) (Pink)
5
4
05
D101 1-874-411- 11
(AE/AF LOCK)
6 4 SELF-TIMER/
1
D201
3
SMILE SHUTTER/
AF ILLUMINATOR
Y
B
CAUTION
LND202
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
G
LND201
05
1-874-413- 11
30 2
LND103 LND104
1 2
Black
Red
LND039 T001
4 3
LND036 LND035
05
K D001 A
1-874-411- 11
SP901
SPEAKER
TRIGGER TRIGGER_GND
Note: BT900 (lithium battery), C901, MIC901, SP901, harness (HN-059) XE_L XE_H
and harness (HN-060) are not included in ST-180 complete board.
FLASH UNIT
DSC-W120/W125_L2
4-22 ST-180, AF-112
SW-520 (2 layers)
: Uses unleaded solder.
3 S003 4
2 S008 1
4 3
1 2
W (ZOOM) T
BL-H LND001
TO LCD901
(BACKLIGHT) S010
BL-L LND002
(MODE DIAL)
11
1
VDR001
CN001
9
11 10
8
17
18
Note: S010 (Mode dial) is not supplied, but this is
10
included in SW-520 complete board.
8
7
RB001
12
1
1
RB0032
8
7
RB004
14 13 2 12
S010
6
2
8
2
16
15
3
4
D001
2
1
3
MENU HOME
v
3 S001 4 3 S002 4
(DISP)
1 2 1 2
4
S006 2
1
8
7
RB002
b B
2
4 3
4 3
3 1
V
(SELF-TIMER)
1
S005 3
N 2
4 1 3
3 S012 4 S011
1 2
SLIDESHOW 2 4
1-874-412- 11
05 1-874-412- 11
05
DSC-W120/W125_L2
4-23 SW-520
MC-189 (2 layers)
: Uses unleaded solder.
LND038 LND039
LND037
LND035
LND033
LND031
LND029
LND027
LND025
LND023
LND021
LND019
LND017
LND015
LND013
LND011
LND009
LND007
LND005
LND003
LND002 LND001
LND036
LND034
LND032
LND030
LND028
LND026
LND024
LND022
LND020
LND018
LND016
LND014
LND012
LND010
LND008
LND006
LND004
(MULTI CONNECTOR)
28 26 CN001 2
27 Note: CN001 (multi connector) is not supplied,
25 1 but this is included in MC-189 flexible complete board.
R004
LF001
4
2
3
MC-189
1-874-415- 11
05
DSC-W120/W125_L2
4-24E MC-189
NOTE
A B C
D E
DSC-W120/W125_L2
Ver. 1.2 2008.05
The changed portions from 5. REPAIR PARTS LIST
Ver. 1.1 are shown in blue.
(ENGLISH)
NOTE: When indicating parts by reference number,
-XX, -X mean standardized parts, so they may have some differences from please include the board name.
the original one.
Items marked * are not stocked since they are seldom required for routine The components identified by mark 0 or
service. Some delay should be anticipated when ordering these items. dotted line with mark 0 are critical for safety.
The mechanical parts with no reference number in the exploded views are not Replace only with part number specified.
supplied. Les composants identifis par une marque
Due to standardization, replacements in the parts list may be different from 0 sont critiques pour la scurit.
the parts specified in the diagrams or the components used on the set. Ne les remplacer que par une pice portant
CAPACITORS: le numro spcifi.
uF: F
COILS Color Indication of Appearance Parts
uH: H Example:
RESISTORS (SILVER) : Cabinets Color
All resistors are in ohms. (Silver) : Parts Color
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
SEMICONDUCTORS
In each case, u: , for example:
uA...: A... , uPA... , PA... ,
uPB... , PB... , uPC... , PC... ,
uPD..., PD...
(JAPANESE)
, ,
-XX, -X,
* 00
uFF
uHH
uA..., uPA..., uPB..., uPC..., uPD... (SILVER):
A..., PA..., PB..., PC..., PD... (Silver) :
Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J : Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
TW : Taiwan model
TH : Thai model
DSC-W120/W125_L2
5-1
5. REPAIR PARTS LIST
#20
#20
8 14
ns 13
LCD901
11
#20
#118
12
7
5
#20
#20 3
Front Section
(See page 5-3)
2
#20
Note: Refer to HELP 1: LCD Window Adhesive Sheet Kit Note: LCDKITHELP1: LCD
when replace the LCD window adhesive sheet kit. Window Adhesive Sheet Kit
Ref. No. Part No. Description Ref. No. Part No. Description
1 3-289-769-01 CABINET (L), SIDE 8 X-2188-891-1 CABINET (REAR (120BK)) ASSY
(W120: SILVER, BLACK/W125) (W120: BLACK)
1 3-289-769-11 CABINET (L), SIDE (W120: BLUE) 8 X-2188-892-1 CABINET (REAR (120BL)) ASSY (W120: BLUE)
1 3-289-769-21 CABINET (L), SIDE (W120: PINK) 8 X-2188-893-1 CABINET (REAR (120PK)) ASSY (W120: PINK)
2 3-289-776-01 CABINET (R), SIDE
(W120: SILVER, BLACK/W125) 8 X-2188-894-1 CABINET (REAR (125BK)) ASSY (W125)
2 3-289-776-11 CABINET (R), SIDE (W120: BLUE) 9 3-289-745-01 SHEET KIT, LCD WINDOW ADHESIVE (Note)
10 3-289-766-01 WINDOW, LCD
2 3-289-776-21 CABINET (R), SIDE (W120: PINK) 11 1-875-540-11 SW-533 FLEXIBLE BOARD
3 3-289-757-01 SCREW, TRIPOD 12 A-1494-316-A SW-520 BOARD, COMPLETE
* 4 3-289-782-01 SHEET, LCD FLEXIBLE FIXED
* 5 3-289-763-01 SHEET, LCD INSULATING * 13 3-289-767-01 SHEET, ZOOM BLIND
* 6 3-289-759-01 FRAME, LCD 14 3-289-762-01 DIAL, MODE
LCD901 8-753-296-94 ACX358AKR-3
* 7 3-093-800-01 GASKET (230) #20 2-635-591-31 SCREW (M1.4), NEW TRUSTAR P2 (Silver)
8 X-2188-890-1 CABINET (REAR (120SL)) ASSY #118 2-655-580-01 SCREW 0+P2 M1.4 NEWTRU-STAR (Black)
(W120: SILVER)
DSC-W120/W125_L2
5-2
5. REPAIR PARTS LIST
BT Holder Section 53
(See page 5-4)
54
(including IC003 (CCD imager) and
CD-719 flexible complete board) (Note 1, 2)
55
#30
52
#20
51
Lens Section
(See page 5-6)
Note 1: 4 - 3
Note 2: 2CCD
1
Ref. No. Part No. Description Ref. No. Part No. Description
51 X-2188-883-1 CABINET (FRONT (7.2SL)) ASSY * 53 3-289-781-01 TAPE (AF)
(W120: SILVER) 54 A-1543-224-A SERVICE, CCD BLOCK ASSY
51 X-2188-884-1 CABINET (FRONT (7.2BK)) ASSY (including IC003 (CCD imager) and CD-719
(W120: BLACK/W125) flexible complete board) (Note1, 2)
51 X-2188-885-1 CABINET (FRONT (7.2BL)) ASSY (W120: BLUE) * 55 3-289-764-01 GASKET (280)
51 X-2188-886-1 CABINET (FRONT (7.2PK)) ASSY (W120: PINK) #20 2-635-591-31 SCREW (M1.4), NEW TRUSTAR P2 (Silver)
52 3-289-768-01 WINDOW, OVF #30 3-086-156-11 SCREW B1.2 (White)
DSC-W120/W125_L2
5-3
5. REPAIR PARTS LIST
BT903
ns
(Note) BT902 #3
(Note)
105 106 107
108
Cabinet (Upper) Section 111
(See page 5-5) 104
#20
BT901
(Note)
110
112
ns
ns
113
103
101
102
Ref. No. Part No. Description Ref. No. Part No. Description
101 X-2188-901-1 HOLDER (SL) ASSY, BT (W120: SILVER) 107 1-965-767-11 HARNESS (HN-068) (White)
101 X-2188-902-1 HOLDER (BK) ASSY, BT (W120: BLACK/W125)
101 X-2188-903-1 HOLDER (BL) ASSY, BT (W120: BLUE) 108 1-965-768-11 HARNESS (HN-069) (Black)
101 X-2188-904-1 HOLDER (PK) ASSY, BT (W120: PINK) 109 1-874-856-11 ST-188 FLEXIBLE BOARD
* 102 3-288-271-01 LID, BT (W120: SILVER) 110 A-1512-914-A SY-189 BOARD, COMPLETE (SERVICE)
* 111 3-289-783-01 SHEET (SY), RADIATION
* 102 3-288-271-11 LID, BT (W120: BLACK/W125) 112 A-1494-320-A MC-189 FLEXIBLE BOARD, COMPLETE
* 102 3-288-271-21 LID, BT (W120: BLUE)
* 102 3-288-271-31 LID, BT (W120: PINK) * 113 3-289-758-01 SHEET METAL, MULTI FIXED
* 103 3-288-272-01 PLATE, BT HINGE * 114 3-298-230-01 TAPE (N2)
* 104 3-289-756-01 LID, DC (W120: SILVER, BLACK/W125) BT901 1-780-456-21 TERMINAL BOARD, BATTERY (Note)
BT902 1-780-456-21 TERMINAL BOARD, BATTERY (Note)
* 104 3-289-756-11 LID, DC (W120: BLUE) BT903 1-780-456-21 TERMINAL BOARD, BATTERY (Note)
* 104 3-289-756-21 LID, DC (W120: PINK)
* 105 3-292-292-01 CUSHION, ST LIGHT INTERCEPTION #3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
106 1-965-766-11 HARNESS (HN-067) (Red) #20 2-635-591-31 SCREW (M1.4), NEW TRUSTAR P2 (Silver)
DSC-W120/W125_L2
5-4
5. REPAIR PARTS LIST
HARDWARE LIST
157
SP901
MIC901
158
160
159
152
161
ns 154
(Note)
151
162
153 C901
155 (Note)
#5
156 BT900
! : Board
BT900 (LITHIUM RECHARGEABLE BATTERY)
on the mount position.
(See page 4-22) 163
Note: Refer to HELP 6: Sheets and Harness of ST-180 Board when CAUTION
replace harness (HN-059/060). Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Note: HN-059/060HELP 6: Sheets
and Harness of ST-180 Board
Refer to page 5-1 for mark 0.
Ref. No. Part No. Description Ref. No. Part No. Description
151 A-1494-315-A ST-180 BOARD, COMPLETE 159 1-965-682-11 HARNESS (HN-061) (Yellow)
0*152 1-480-556-11 FLASH UNIT * 160 3-289-765-01 SHEET, CAPACITOR PROTECTION
153 1-965-681-11 HARNESS (HN-060) (Blue) (Note) * 161 3-289-761-01 RETAINER, AF
154 1-965-680-11 HARNESS (HN-059) (Pink) (Note) 162 A-1494-317-A AF-112 BOARD, COMPLETE
* 155 3-289-779-01 SHEET, LITHIUM INSULATING * 163 3-289-760-01 HOLDER, CAPACITOR
DSC-W120/W125_L2
5-5
Ver. 1.4 2008.08
The changed portions from
Ver. 1.3 are shown in blue.
5. REPAIR PARTS LIST
HARDWARE LIST
#30
(Note 4)
201
(Note 1) ns
#30
205 (Note 4)
(Note 5)
ns
209
(Note 3)
204 #30
(Note 2) (Note 4)
203
202 (Note 2) 208
(Note 2) (Note 3)
207
206 (Note 3)
(Note 3)
Note 1: Refer to 2-3. Precuations when Holding the Lens Note 3: Refer to 2-5. Lens Motor Replacing Method on
Block on page 2-6 when detach or replace the lens page 2-8 when replace the zoom gear block or the
block. optical stepping motor.
Note 1: 2 - 6 Note 3:
2-3. Precautions when Holding the Lens 2-82-5. Lens Mo-
Block tor Replacing Method
Note 2: Refer to 2-4. Barrier Assy Replacing Method on Note 4: Tightening torque = 0.049 0.01 Nm (0.5 0.1
page 2-7 when replace the barrier assy. kgfcm)
Note 2: 2 - 7 2 - 4 . Note 4: 0 . 0 4 9 0 . 0 1 N m 0 . 5 0 . 1
Barrier Assy Replacing Method kgfcm
Note 5: Repaste it after replacing the optical finder if the
seal to which the data value for service is written
is pasted to it when the optical finder is repaired.
Note 5:
()
Ref. No. Part No. Description Ref. No. Part No. Description
201 A-1512-913-A LSV-1250A (SERVICE) (Note 1) 206 X-2187-865-1 GEAR (S), NARUTO (Note 3)
202 3-278-941-01 RING A (Y), ORNAMENTAL (Note 2) 207 3-268-545-01 PLATE SPRING, FG (Note 3)
203 2-691-890-11 TAPE, BARRIER (Note 2) 208 1-480-381-11 GEAR BLOCK, ZOOM (1250) (Note 3)
204 A-1437-489-A BARRIER ASSY (SDPW) (Note 2) 209 1-787-672-11 STEPPING MOTOR, OPTICAL (F1250) (Note 3)
205 1-788-635-11 FINDER, OPTICAL (1250) (Note 5) #30 3-086-156-11 SCREW B1.2 (White) (Note 4)
DSC-W120/W125_L2
5-6
AF-112 CD-719 MC-189 ST-180
0 BT900 1-756-710-12 LITHIUM RECHARGEABLE BATTERY Note 1: Be sure to read Precuations for Replacement of
Imager on page 4-2.
< CAPACITOR >
Note 1: 4 - 3
C001 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V
C002 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V
0 C005 1-100-758-11 CERAMIC CHIP 0.047uF 10% 250V Note 2: There are two types of modules used in the CCD
C006 1-164-933-11 CERAMIC CHIP 220PF 10% 50V BLOCK ASSY.
* C008 1-112-746-11 CERAMIC CHIP 4.7uF 10% 6.3V They are interchangeability and only one type is
available for repair part.
< CONNECTOR >
Note 2: 2CCD
* CN002 1-817-391-81 CONNECTOR, FPC (ZIF) 31P 1
Refer to page 5-1 for mark 0.
DSC-W120/W125_L2
5-7
SW-520
Ref. No. Part No. Description Ref. No. Part No. Description
A-1494-316-A SW-520 BOARD, COMPLETE
***********************
(S010 (Mode dial) is not supplied, but this is included
in SW-520 complete board.)
DSC-W120/W125_L2
5-8
Ver. 1.2 2008.05
The changed portions from
Ver. 1.1 are shown in blue.
DSC-W120/W125_L2
5-13
Ver. 1.2 2008.05
The changed portions from
Ver. 1.1 are shown in blue.
Instruction Manual
3-286-605-01 (JAPANESE) (J)
3-286-605-11 (ENGLISH) (CND, AEP, UK, E, HK, AUS, TH, JE)
3-286-605-21 (FRENCH, ITALIAN) (CND, AEP)
3-286-605-31 (SPANISH, PORTUGUESE) (AEP, E, AR, JE)
3-286-605-41 (GERMAN, DUTCH) (AEP)
3-286-605-51 (TRADITIONAL CHINESE, SIMPLIFIED CHINESE)
(E, HK, JE)
3-286-605-61 (RUSSIAN, UKRAINIAN) (AEP)
3-286-605-71 (ARABIC, PERSIAN) (E)
3-286-605-81 (KOREAN) (KR, JE)
3-286-605-91 (POLISH, CZECH) (AEP)
3-286-606-11 (HUNGARIAN, SLOVAK) (AEP)
3-286-606-21 (SWEDISH, FINNISH) (AEP)
3-286-606-31 (NORWEGIAN, DANISH) (AEP)
3-286-606-41 (MALAY) (E)
3-286-606-51 (TURKISH, GREEK) (AEP)
3-286-606-61 (ENGLISH, SPANISH) (US)
3-286-606-71 (SIMPLIFIED CHINESE) (CH)
3-700-781-81 (THAI) (TH)
CD-ROM
Cyber-shot application software
Cyber-shot Handbook Cyber-shot Handbook (PDF)
Cyber-shot Step-up Guide The CD-ROM supplied contains all of language version of
3-286-601-01 (EXCEPT J) the Cyber-shot Handbook (PDF) for printing.
3-294-912-01 (J) The printed matter is not supplied. If required, please
order it with the part number below.
(Only for destination Japanese model)
3-286-602-01 (JAPANESE) 3-286-603-11 (RUSSIAN)
3-286-602-11 (ENGLISH) 3-286-603-21 (ARABIC)
3-286-602-21 (FRENCH) 3-286-603-31 (PERSIAN)
3-286-602-31 (ITALIAN) 3-286-603-41 (KOREAN)
3-286-602-41 (SPANISH) 3-286-603-51 (POLISH)
3-286-602-51 (PORTUGUESE) 3-286-603-61 (CZECH)
3-286-602-61 (GERMAN) 3-286-603-71 (HUNGARIAN)
3-286-602-71 (DUTCH) 3-286-603-81 (SLOVAK)
3-286-602-81 (TRADITIONAL CHINESE) 3-286-603-91 (SWEDISH)
3-286-602-91 (SIMPLIFIED CHINESE) 3-286-604-11 (FINNISH)
3-286-604-21 (NORWEGIAN)
3-286-604-31 (DANISH)
3-286-604-41 (THAI)
3-286-604-51 (MALAY)
3-286-604-61 (TURKISH)
3-286-604-71 (GREEK)
3-286-604-81 (UKRAINIAN)
DSC-W120/W125_L2
5-14E
DSC-W120/W125
LEVEL 2
US Model
SERVICE MANUAL Canadian Model
AEP Model
Ver. 1.3 2008.06 UK Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Argentine Model
Brazilian Model
SUPPLEMENT-1 Thai Model
Japanese Model
File this supplement with the service manual.
(DI08-159) Tourist Model
2008F0500-1
DSC-W120/W125_L2 2008.6
9-852-264-81 Sony EMCS Co. Published by Kohda TEC
& : Points added portion.
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
ST-180 BOARD (1/2) (FLASH DRIVE)
(Service manual page 4-15, Location C-1 to D-2)
Suffix: -11 Suffix: -21
NC 29 NC 29
VL_3V 30 VL_3V VL_3V 30 VL_3V
NC 31 NC 31
4 2 4 2
1
C005
L0
C005
L0
R003 R003 R006
DSC-W120/W125_L2
2
HARDWARE LIST (1/7)
#1: M1.7 X 2.5 #2: M1.7 X 4.0 #3: M1.7 X 2.5 #4: M1.4 X 2.5 (Tapping)
(Black) (Black) (Red) (Dark Silver)
2-635-562-11 2-635-562-31 2-660-401-01 3-348-998-81
#5: M1.7 X 3.5 (Tapping) #6: M1.4 X 1.7 #7: M1.7 X 1.6 #8: M1.7 X 3.5 (Tapping)
(Black) (Silver) (Black) (Silver)
3-080-204-01 2-598-474-01 7-627-552-18 3-078-890-01
#9: M1.7 X 5.0 (Tapping) #10: M1.7 X 4.0 #11: M1.7 X 4.0 (Tapping) #12: M1.7 X 5.0 (Tapping)
(Silver) (Silver) (Silver) (Black)
3-078-890-21 2-599-475-31 3-078-890-11 3-080-204-21
#13: M1.7 X 2.5 (Tapping) #14: M1.7 X 2.5 #15: M1.4 X 1.5 #16: M1.4 X 2.5
(Silver) (Silver) (Silver) (Silver)
3-085-397-01 2-599-475-11 3-062-214-01 2-586-337-01
#17: M1.7 X 1.5 #18: M1.4 X 2.5 #19: M1.2 X 4.0 (Tapping) #20: M1.4 X 3.0
(Silver) (Silver) (Red) (Silver)
2-586-389-01 2-635-591-21 3-086-156-21 2-635-591-31
1.5
2.5 4.0 3.0
3.5
HARDWARE LIST (2/7)
#21: M1.4 X 3.0 #22: M1.7 X 5.0 (Tapping) #23: M1.7 X 4.0 (Tapping) #24: B1.7 X 5.5 (Tapping)
(Black) (Silver) (Black) (Black)
2-662-396-21 3-083-261-01 3-080-204-11 4-679-805-11
#25: M1.7 X 3.0 #26: M1.4 X 2.0 #27: M1.4 X 2.0 #28: M1.4 X 4.0 (Tapping)
(Black) (Silver) (Black) (Silver)
2-635-562-21 2-635-591-11 2-662-396-11 3-348-998-61
#29: M1.4 X 2.5 #30: M1.2 X 3.5 (Tapping) #31: M3.0 X 4.0 #32: M2.0 X 4.5 (Tapping)
(Black) (White) (Silver) (Silver)
2-662-396-01 3-086-156-11 2-102-434-01 2-102-498-01
#33: M3.0 X 6.0 #34: M3.0 X 8.0 #35: M4.0 X 6.0 (Tapping) #36: M3.0 X 6.0
(Silver) (Black) (Silver) (Silver)
3-077-331-21 3-077-331-41 3-975-291-02 4-886-821-11
#37: M2.0 X 6.0 (Tapping) #38: M3.0 X 20.0 (Tapping) #39: M2.6 X 5.0 (Tapping) #40: M2.0 X 4.0 (Tapping)
(Black) (Silver) (Black) (Silver)
3-080-206-31 7-685-651-79 7-685-791-09 7-685-851-04
3.0
20.0
6.0 5.0 4.0
HARDWARE LIST (3/7)
#41: M3.0 X 8.0 (Tapping) #42: M2.0 X 4.0 (Tapping) #43: M1.7 X 4.0 #44: M1.7 X 3.0 (Tapping)
(Silver) (Silver) (Red) (Silver)
3-065-748-01 7-628-253-00 2-660-401-31 3-078-890-61
#45: M1.4 X 2.5 #46: M1.7 X 3.0 #47: M1.4 X 3.0 (Tapping) #48: M1.7 X 2.5
(Silver) (Red) (Silver) (Silver)
2-587-151-01 2-660-401-11 2-665-774-01 3-973-497-91
#49: M2.0 X 4.0 #50: M2.0 X 3.0 #51: M2.0 X 2.5 #52: M2.0 X 4.0 (Tapping)
(Black) (Red) (Silver) (Black)
2-630-005-31 2-891-494-11 3-073-686-01 3-080-206-11
#53: M2.0 X 5.0 (Tapping) #54: M1.75 X 6.0 (Tapping) #55: M2.0 X 4.0 #56: M2.0 X 3.5
(Black) (Black) (Silver) (Silver)
3-080-206-21 3-318-203-11 2-655-582-11 3-067-187-11
#57: M1.7 X 4.0 #58: M2.0 X 6.0 (Tapping) #59: M2.0 X 5.0 (Tapping) #60: M2.6 X 5.0
(Black) (Silver) (Silver) (Black)
7-627-852-18 3-719-408-11 3-080-205-21 3-061-062-11
#61: M3.0 X 10.0 #62: M2.0 X 3.0 #63: M5.0 X 12.5 #64: M1.7 X 5.0 (Tapping)
(Black) (Silver) (Black) (Silver)
7-682-549-09 3-080-202-21 3-060-811-21 2-666-551-21
10.0 12.5
3.0 5.0
#65: M1.4 X 3.5 #66: M1.4 X 1.4 #67: M1.4 X 2.0 #68: M1.7 X 4.0
(Silver) (Silver) (Silver) (Silver)
2-635-591-01 2-635-591-41 3-389-523-16 2-655-581-01
#69: M1.7 X 3.0 #70: M1.7 X 5.0 #71: M1.4 X 2.0 #72: M1.4 X 2.0
(Silver) (Silver) (Red) (Silver)
2-599-475-21 2-599-475-41 3-208-537-01 4-663-621-41
#73: M1.2 X 4.0 (Tapping) #74: M1.7 X 6.0 (Tapping) #75: M1.7 X 3.5 (Tapping) #76: M1.7 X 4.0 (Tapping)
(Black) (Silver) (Silver) (Silver)
3-086-156-61 2-666-551-31 2-666-551-01 2-666-551-11
#77: M1.2 X 5.0 (Tapping) #78: M1.4 X 3.5 #79: M1.4X 2.0 #80: M1.4X 2.0
(Silver) (Red) (Silver) (Black)
3-086-156-31 3-208-537-11 2-587-151-11 3-279-411-01
#81: M1.7 X 2.5 #82: M1.4 X 1.4 #83: M1.7 X 7.0 (Tapping) #84: M2.0 X 3.0
(Silver) (Silver) (Black) (Silver)
2-515-756-01 3-272-251-01 3-080-204-41 3-072-453-11
#85: M1.7 X 2.5 #86: M1.7 X 4.0 (Tapping) #87: M1.6 X 5.3 #88: M1.6 X 5.9 (Tapping)
(Black) (Silver) (Black) (Silver)
2-515-483-11 2-695-434-21 2-689-328-01 2-689-015-01
5.9
2.5 5.3
4.0
#89: M2.0 X 5.5 (Tapping) #90: M1.7 X 3.0 #91: M1.7 X 3.0 (Tapping) #92: M2.0 X 3.9
(Silver) (Silver) (Silver) (Black)
2-695-575-01 3-271-395-01 2-695-434-11 3-268-954-01
#93: M1.7 X 3.5 (Tapping) #94: M1.7 X 4.0 #95: M3.0 X 8.0 (Tapping) #96: M1.4 X 2.5
(Silver) (Black) (Black) (Silver)
3-254-082-01 2-515-483-31 7-685-646-79 2-587-151-21
#97: M1.4 X 2.5 #98: M3.0 X 8.0 #99: M2.5 X 6.0 (Tapping) #100: M2.0 X 6.0
(Black) (Silver) (Silver) (Black)
2-662-396-31 3-077-331-01 3-776-750-02 3-080-203-51
#101: M2.0 X 5.0 #102: M2.6 X 8.0 #103: M2.6 X 10.0 #104: M3.0 X 8.0
(Silver) (Black) (Silver) (Black)
7-621-555-39 7-621-284-30 7-685-794-09 7-682-548-09
#105: M2.0 X 4.0 #106: M2.0 X 6.0 #107: M2.0 X 5.0 #108: M1.7 X 3.0 (Tapping)
(Red) (Black) (Silver) (Black)
2-891-494-31 3-713-786-11 3-032-750-01 2-695-430-01
#109: M1.7 X 3.0 #110: M2.0 X 3.0 #111: M1.7 X 4.0 (Tapping) #112: M1.4 X 5.0
(Black) (Black) (Black) (Black)
2-515-483-21 2-630-005-21 2-887-124-01 2-178-410-11
#113: M1.7 X 5.0 #114: M2.0 X 5.5 (Tapping) #115: M1.4 X 3.5 (Tapping) #116: M2.0 X 3.5 (Tapping)
(Black) (Silver) (Silver) (Silver)
2-635-562-41 2-698-464-01 3-348-998-51 2-695-435-01
#117: M1.7 X 4.5 (Tapping) #118: M1.4 X 2.0 #119: M2.6 X 5.0 #120: M2.6 X 6.0
(Silver) (Black) (Black) (Silver)
2-695-429-31 2-655-580-01 7-627-556-58 7-621-770-67
#121: M2.0 X 4.0 (Tapping) #122: M3.0 X 6.0 #123: M4.0 X 8.0 #124: M1.7 X 2.0
(Silver) (Black) (Black) (Silver)
3-080-205-11 7-682-547-09 7-682-561-09 2-599-475-01
Revision History
S.M. Rev.
Ver. Date History Contents
issued
1.0 2008.01 Official Release
1.1 2008.02 Revised-1 Correction of Service Note Yes
(A1 DI07-279) Correction of Frame Schematic Diagram
S.M. correction: Page 1-6, Page 4-1
1.2 2008.05 Revised-2 Addition of Thai Model Yes
(A2 DI08-065) S.M. revised: Page 3, Page 5-1, Page 5-13,
Page 5-14
1.3 2008.06 Supplement-1 Change of Boards Suffix No. No
(S1 DI08-159)
1.4 2008.08 Revised-3 Addition of Note for Lens Section Yes
(A3 DI08-221) S.M. revised: Page 5-6
DSC-W120/W125_L2