Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Description
The Loop-IP6510 Router/Bridge provides remote bridge
connectivity from 4 Ethernet ports to 2 fixed WAN ports
and also to 2 optional WAN slots. Whereas the 2 fixed
WAN ports are always Ethernet, choices are available for
Features the 2 optional WAN slots. Each of the 2 optional slots can
accept one of 4 choices of plug-in cards, which are
Supports 10/100 BaseT speed auto-sensing,
half/full duplex auto-negotiation and auto (a) a card with dual T1 port
MDI/MDI-X crossover (b) a card with dual E1 port
WAN interfaces
(c) a card with one 10/100 BaseT fast Ethernet port
2 built-in 10/100BaseT WAN interfaces for
uplink (d) a card with one SFP (mini-GBIC) housing for 100M-FX
2 cold plug-in slots supporting any 2 of the fast Ethernet port
following cards:
E1 card: 2 ports per card, up to 4 ports Using the optional dual E1/T1 card, up to 4 E1/T1 lines
per system can be used for WAN connectivity, either separately or in a
T1 card: 2 ports per card, up to 4 ports single bundle.
per system
Electrical RJ45 Ethernet card: 1 port
per card, up to 2 ports per system All Ethernet, WAN, and LAN ports have speed
Optical SFP Ethernet card: 1 port per auto-sensing, half/full duplex auto-negotiation, and auto
card, up to 2 ports per system MDI/MDI-X crossover features. All serial (E1/T1) WAN
LAN interfaces interfaces support PPP, MLPPP, Frame Relay,
Four 10/100BaseT LAN interfaces for Cisco-compatible HDLC and HDLC protocols.
downlink
RS232 console port The Loop-IP6510 Router/Bridge has a DB9S console port,
Supports SNMP management
which allows users to execute in-service diagnostics and
Supports Telnet and SSH remote
management fault isolation from a local terminal. It also allows users to
Supports remote software upgrade manage remotely via Telnet, SSH and SNMP through
Supports 802.1a, 802.1w, 802.1q and Ethernet or WAN ports. Multicolor LED indicators and an
802.1ad ACO (Alarm Cut Off) button are provided on the front
Supports remote bridges panel.
Supports router
1
Loop-IP6510 Multiple WAN Router/Bridge Ethernet Access
Ordering Information
To specify options, choose from the list below.
Note: RoHS compliant units are identified by the letter G appearing at the end of the ordering code.
Note: Non-Loop SFP modules are not guaranteed to work with our equipments. It is strongly recommended to buy
Loop-logo SFP modules.
Where aa and bb are used to select the additional cold plug-in modules. If this option is not required, omit
the aa or bb field in the ordering code
aa, bb= Description Notes
2T1 Dual T1 interface with RJ48C connector
E1-120 ohm/T1 jumper selectable
2E120 Dual E1-120 ohm interface with RJ48C connector
1FE One 10/100 BaseT Fast Ethernet
SFPH SFP (mini-GBIC) housing for 100M-FX SFP optical modules not included
2
Loop-IP6510 Multiple WAN Router/Bridge Ethernet Access
E1 Line Interface
Line Rate 2.048M bps 50 ppm
Line Code HDB3
Output Signal ITU G.703
Connector RJ48C
Loopbacks Line Loopback, Payload Loopback
Test Pattern 20-bit QRSS, 3-in-24, 1-in-8, 2-in-8, 1:1
T1 Line Interface
Line Rate 1.544 Mbps 50 bps
Line Code AMI or B8ZS
Output Signal DS1
Connector RJ48C
Loopbacks Line Loopback, Payload Loopback
Test Pattern 20-bit QRSS, 3-in-24, 1-in-8, 2-in-8, 1:1
LAN Interface
4 10/100BaseT interfaces
Speed auto-sensing
Half/full duplex auto-negotiation
Auto MDI/MDI-X crossover
Management
SNMP v1, v2c
Telnet
SSH
Bridge
STP, RSTP
802.1q supported
Cisco ISL packet transparent
VLAN packet transparent
User configurable aging time
Up to 16K MAC table
Padding/un-padding Ethernet FCS
Support IEEE 802.1ad Q-in-Q
Router
Routing protocol: RIP-I, RIP-II, OSPF
Static route
3
Loop-IP6510 Multiple WAN Router/Bridge Ethernet Access
Address Translation
NAT/NAPT
Static address table for NAT
Port forwarding table for NAPT (Virtual Service)
Supports port range from 1 to 65535
DHCP
DHCP server support for LAN users (RFC2131, RFC2132)
BOOTP compatible
DHCP relay
QoS
QoS based on rate limit
Classification based on
Outbound direction
Source/destination IP addresses
DSCP
Protocol types
Port number range
Electrical
Power Source (AC) 100 to 240 Vac, 0.8A
Power Source (DC) -36 to -72 Vdc, 1.2A
Power Consumption < 20 W
Standards Compliance
IEEE 802.1d bridge, 802.1w RSTP, 802.1q VLAN, 802.1ad Q-in-Q
IETF RIP1 (RFC1058), RIP2 (RFC1389)
ITU G.703, G.704, G.823
Compliance
EMC/EMI FCC15 Class A, EN55022, EN55024
Safety UL60950, IEC60950-1 (CB)
Network FCC68, CS-03
4
Loop-IP6510 Multiple WAN Router/Bridge Ethernet Access
Ground
Screw
USBPort*
AC
Power ACO WAN Console
DC LAN 1- 4
Power WAN1-2 Backup* Port
LEDs
* Future option
E1/T1 card
Application Illustrations
E1/T1
LAN LAN
Network
IP6510 IP6510
Multiple WANs
5
Loop-IP6510 Multiple WAN Router/Bridge Ethernet Access
E1/T1
IP6510 IP6510
MLPPP Bundle
Backup
Network
DSL DSL
Ethernet Ethernet
E1/T1
Network
IP6510 IP6510