Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
INSTALLATION MANUAL
Applied Machines: C754/C654/C554/C454/C364/C284/C224
COLOR MFP: 75 ppm/65 ppm/55 ppm/45 ppm/36 ppm/28 ppm/22 ppm
Product Code: A2X0/A2X1/A2XK/A4FJ/A161/A4FK/A4FM
8. Mounting
I. Accessory parts bracket C*2
No. Name Shape Qty 1
1. Horizontal
transport unit A3EPIXC007DB
9. Mounting
1
bracket D*2
1
A3EPIXC001DA
2. Sensor unit*2
A3EPIXC008DB
10. Mounting
1
bracket E*2 1
A2YVIXC002DA A3EPIXC009DA
1 A3EPIXC052DA
5. Staple cartridge 1
1
A3EPIXC010DA
A3EP-9550-02
E-1
Note:
No. Name Shape Qty
Before installing this finisher to C554/C454/
16. Mounting screw C364/C284/C224, the paper feed cabinet PC-
1 110, PC-210, PC-410, or the desk DK-510
needs to be installed in advance.
A0HRIXC011DA This manual provides the illustrations of the
17. Screw A *3 accessory parts and machine that may be
10 slightly different in shape from yours. In that
9646 case, instead of the illustrations, use the
18. Screw B*2 appearance of your machine to follow the
1 installation procedure. This does not cause any
significant change or problem with the proce-
9738
dure.
19. Screw C*2 If none of the later steps instruct you to use the
5 parts including screw and cover that you
removed following the instructions described in
9J08IXC075DA this manual, discard them.
20. Screw D
2
9654
II. Confirmation before installation
21. Installation 1. To move the finisher, be sure to push it in the
manual directions of the arrows as shown in the illustra-
1 tion. (Precaution against falling of the finisher.)
set
4980IXC019DA
E-2
III. Installation procedures 5. Attach the mounting bracket G to the mounting
bracket B. (One supplied screw D)
Note:
The parts to be used and the procedure for install-
ing this option depend on the type of the main unit
to which this option is installed. Please go to one
of the following pages that correspond to the type
of your main unit.
When installing this option to C754/C654: E-3
When installing this option to C554/C454/C364/
C284/C224: E-5
A2Y1IXC010DA
A3EPIXC014DA
A3EPIXC038DA
A3EPIXC036DB
E-3
8. Remove the cover shown in the illustration. 11. Attach the guide plate B. (Two screws removed
(Three screws) in step 9)
A3EPIXC039DA A3EPIXC042DA
9. Remove the cover shown in the illustration from 12. Attach the supplied mounting bracket A (front) to
the front of the horizontal transport unit. (Two the left side of the main unit. (Three supplied
screws) screws A)
A3EPIXC040DA A3EPIXC043DA
10. Attach the guide plate A to the horizontal trans- 13. Attach the supplied mounting bracket B (rear).
port unit by fitting the two tabs into the slots. (Three supplied screws A)
A3EPIXC041DA A3EPIXC044DA
E-4
14. Remove one knockout (front) from the lower left <When installing this option to C554/C454/C364/
side of the main unit with nippers. C284/C224>
1. Turn off the machine and unplug the power cord
from the power outlet.
2. Remove the users guide holder from the main
unit.
A2Y1IXC022DA
A3EPIXC045DA
A3EPIXC035DA
A2YVIXC004DB
E-5
6. Reattach the upper left cover removed in step 4 11. Peel the seal off the cover removed in step 9 as
to the main unit. (Three screws) shown in the illustration.
7. Close the front door of the main unit.
8. Remove the guide from the main unit.
A3EPIXC059DA
A2YVIXC005DA 12. Attach the supplied sensor unit to the main unit
by fitting the two tabs into the slots.
9. Remove the cover shown in the illustration from
the main unit. (Two screws)
A2YVIXC006DA
A2YVIXC012DA
A3EPIXC058DA
E-6
14. Connect the sensor units connector to the con- 17. Attach the mounting bracket G to the mounting
nector of the harness removed in step 10. bracket D. (One supplied screw D)
A2YVIXC013DA A3EPIXC054DB
15. Route the harness through the two wire saddles 18. Reattach the cover removed in step 9 to the
and the edge cover. main unit. (Two screws removed in step 9)
19. Remove the protective tape of the horizontal
transport unit.
A2YVIXC014DA
A3EPIXC053DB
A3EPIXC015DA
E-7
21. Attach the supplied mounting bracket D (rear). 24. Remove the protective tape and the protective
(Two supplied screws C) materials from the finisher.
A3EPIXC016DA A3EPIXC049DA
Mounting bracket E
A3EPIXC050DA
A3EPIXC019DB
A3EPIXC018DA
E-8
27. Remove the protective tape. 31. Attach the supplied exit tray (lower) to the fin-
28. Remove the screw shown in the illustration and isher. (Two supplied screws A)
remove the label from the finisher.
Label
A3EPIXC023DA
A3EPIXC020DB
32. Insert the supplied exit tray (upper) into the fin-
29. Remove the plate shown in the illustration from isher.
the lower right side of the finisher. (One screw)
A3EPIXC024DA
A3EPIXC021DA
A3EPIXC025DB
A3EPIXC022DA
E-9
34. Open the finisher front door and pull the lever. 36. Verify items and below.
The plate spring of the plate installed in step 30
is contacted with the main unit.
When the lever that was pulled out in step 34 is
pushed back, the finishers screw hole is within
the range of levers mounting hole.
Screw
hole
A3EPIXC026DB
A3EPIXC027DC
Plate spring
A3EPIXC060DA
E-10
(1) Disconnect the connector, and remove the fin- (4) Adjust the height of the four casters.
isher from the main unit.
A3EPIXC029DC
A3EPIXC032DA
A3EPIXC061DA
A3EPIXC031DB
E-11
39. Remove the cover shown in the illustration from 40. Plug in the two connectors of the finisher. Fit the
the back of the main unit. (One screw) head of the cable tie into the mounting hole on
the main unit.
<When installing this option to C754/C654>
<When installing this option to C754/C654>
Connector
Cable tie
A3EPIXC046DA
A3EPIXC047DA
<When installing this option to
C554/C454/C364/C284/C224> <When installing this option to
C554/C454/C364/C284/C224>
Connector
Cable tie
A3CFIXC008DA
A2YUIXC022DA
Wire saddle
A3EPIXC056DA
E-12
42. Reattach the cover removed in step 39.
(One screw)
Note:
Be careful not to pinch the harness.
When installing this option to C554/C454/C364/
C284/C224, insert two tabs A into the holes on
the main unit cover first.
Then fit two tabs B into the holes.
Tab B
Tab A
A3EPIXC057DA
A3EPIXC034DB
E-13