STEEL PIPE FLANGES FOR WATERWORKS SERVICE 11
A
CC t
TILAK
T TF
Table 2. AWWA standard steel-ring flanges, class B* (86 psi) and Class Dt (175-150 psi)
Thickness of Flenge — in
Nominal OD of. IDof Number Diam. of Bolt Diam. of
Pipe Size Flange (A) Flange (B") of, Cirle (C) Bolts Giese B: Clee
in in in Bolts in in ey @
4 900 457 8 7.50 0.625 0.85 0.625,
5 10.09 5.68, 8 8.50 70 0.605 0.685
8 11.00 en 8 9.50 0.730 0688 0.688
3 13.50 a7 8 176 0.750 88 0.688
10 16.00 10.88 2 14.25 ost 0.888 0.688
2 19.00 288 12 17.90 ost 0.088 812
u 21.00 Mag 12 18.75 1.090 oss 0.938
16 23.50 16.19 16 2125 1.000 0.688 1.090
18 25.00 38.19 16 78 1.5 oss 1.082
20 50 20.19 20 25.00 0.688 125
22 20.50 22.19 20 27.95 0.750 1.338
Er 32.00 24.19 20 290 0.750 1.250
26 34.25 24 8175 siz 1312
8 36.50 28 34.00 0875 1312
20 38.75 28 36.00 087 1375
92 41.75 28 98.50 0938 1.500
84 48.15 32 40.50 0.988
36 46.00 32 42.75 1.000,
88 48.75 82 45.25 1.000
40 50.75, 36 4728 31.000,
2 53.00 36 49.50 1.500 1125
“a 25 40. 5178 1.500 1295
may be overbored or counterbored to accommodate larger autside-diameter pipe than shisen az neminal
‘Thies dene te allow a clear ince diameter after eement-mortar lining. Wrench csarance between the pipe OD and bolt
circle must be maintained as well as maffeient gasket seating ares
2. Metric conversion: ominal pipe sie: in. x 25
ron; dimensions: in. < 25.4 = mm: ps » 6805 = kPa
Pressure rating at atmospheri teroperature i §6 psi, These anges have the same CD and drilling ae clase 125 cast iron
Mangos (ANSVASME B16.1) Ia sizes 24 in, and smaller, they also match ANSUASME 819.9 150 yi drilling for stock
Anges
‘Pressure rating at atmospheric temperature: sizes 412 in, inclusive, 178 psi; sies larger than 12 in. 150 psi. The
Asnges have the same diameter and deilling as class 128 cast-iron Manges | ANSVASME B13,1), In sizes 24 in. and smaller
they also mateh ANSVASME B16 5 150-psi standard for steel flanges
The purchaser shall specify the 1D oF the Nange, Wmension B, fer powinal pipe ses 26 in. ani larger. The dismeter of
the Mange bore shall ao: exceed the pipe OD by more than 0.19 0,
Bok: holes shall be drilled *-1a. larger in diameter than the nominal diameter ofthe bolt except as stated in See 4.2312 AWWA C207.01
Teble 2 AWWA standard steel-ring flanges. class B* (86 psi) andl Class Dt (175-150 psii-cont
Thiel
38 of Flame — tn
fominal ol jumber Diam. of Holt Diam. of
PoeSie angela) Hang) ar” ARAB MERE Gas Glesd
in. in, in Belts in in my o
46 57.25 40 BATS 1.500 11s
59.50 4 56.00 1.600 1.250
61.75 a 58.2 1.750 1.250 2.000
64.00 4 60.50 1.756 1.250 2.000
66.25 4 o2n7s 1.750 1379 2.125
00 52 69.25 175 1.500 2.050
66 80.00 2 7.00 1786 1.625 2.500
7” 86.50 6 8250 1.750 1750 2.625
78 £3.00 ot 89.00 2.000 2.000 2.750
84 9.15 6b 95.50 2.000 2.000 2.875
oo 106.60 68 102,00 2.250 2.250 8.000
96 133.25 68 108.50 2.250 2.250 3.250
102 120.00 n 2500 2.500 3.250
108 126.75, R 120.75 2.500 2.500 3375
4 133,50 6 2.750 2.780 8500
120 140.25 76 192.75 2.750 2.750 3.800
128 147.00 80 139.25 3.000 3.000 3750
182 158.78 80 145.75 8.000 3.000 3875
388 160.50 84 152.00 3.250 8.250 4.000
ey 167.25 Ba 158.25 20 3.250 4125,
Noms
1 Ring fangeo say be overbored or couaterbored to accommodate larger aatsde-cianeter pipe than shown as nominal
‘This is done to llow a clear inside diameter afer cement-mertar lining Wrench clearance between the pipe OD ard sal
circle must be maintained as well ar sufficient gasket seating area
2. Metric conversion: nominal pipe size: in. 25 = mre; dimensions: in, x 26-4 = my oxi x G95 = KPa
‘Pressure rating ot atmazpheric temperature i 60 pst These flanges have the same OD and drilling as class 125 eastiton
Ranges (ANSUASME B1C.1) Yn sizes 24 in, and smaller, they also match ANSUASME B165 160 ps driling ee vee.
ange
essure rating at atmospheric temperature: sss 422 in elusive, 176 ps sie larger than 12, 160 ps. These
anges have the same diameter and dling ae clas 126 east ron flanges iANSUVASME B10 1) Ta sizes 24m andemalicn
they also match ANSVASME R165 150421 stondard lor atec! anges,
he purchaser shall specity the 1D of the Range, dimeersion B, for nominal pipe sizes 26 in. and lnnger. The diameter of
the Mange tore shall not exceed the pipe OD by moze than 0.19 i
Bol holes shall be drilled “in, larger tm diamoter than the nouinel diameter of the aolt except as stated in See. 4.23,