Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
MODEL : LK-P32
MOBILE PRINTER
P32 Rev. A 08/14 All specifications are subject to change without notice
Table of Contents
1. Safety Caution 2
2. Unpacking 4
3. Product Overview 5
5. Peripherals Connection 16
6. Printer Specificaiton 18
6-1. Specification 18
1
1. Safety Caution
For higher reliability and safety, consider the following precautionary measures.
Read and follow the instructions carefully before running of the product. WARNING
Failure to follow these instructions could result in fire, electric shock,
or other injuries, or property damage
Indication
Grounding to prevent electric Do not handle the product Do not pull out the power plug to turn off Do not disassemble, repair or modify the
shock with wet hands the product. product.
(Turn off the power at installation, (Potential risk unit malfunction, electric
transportation, wiring and inspection.) shock or fire. When the product needs
WARNING to be repaired, please contact in place
Failure to follow these instructions could result in fire, electric shock, where you ordered.inspection.)
or other injuries, or property damage
CAUTION
Failure to follow these instructions could result in fire, electric shock,
or other injuries, or property damage
Do not pull or touch the power plug with Do not overload the power plug into one
wet hands. outlet. Do not install the product in uneven or Keep product away from the water and
(Potential risk of electric shock or fire) (Potential risk of electric shock or fire) inclined surface. other material.
(You may get hurt and it can be broken (Potential risk of discoloration or
when it falls) electric shock)
Dealer
If the product that needs to be repaired, Please do not give excessive shock.
Do not bend the wire and do not allow the If a power plug is broken or a plug is cut or
please contact in place where you ordered. (Potential risk of fire or unit malfunction)
wire to be pressed by heavy object. worn, do not use it.
(Potential risk of electric shock or fire) (Potential risk of electric shock or fire) (Potential risk of fire or unit malfunction)
2 3
2. Unpacking 3. Product Overview
Standard Front
Control
button
LCD
Printer
Power
button
Rear
Battery Roll paper CD
USB
Battery
4 5
4. Usage and Installation
4-1 Control panel usage
4-1-1. Printer status icons
Bluetooth Battery
Setting Press to select a menu choice on the LCD. 4-1-2. How to check the remaining power
Low Battery
Low Battery
6 7
4-1-3. Configuration setting
Parameter Action/Explanation
Navigate the LCD menus by pressing button.
Auto Gap or BM (Black Mark) and BAT
Parameter Action/Explanation Auto Setting (Battery) Calibration
Parameter Action/Explanation
To do BAT(Battery) Calibration, REMOVE Battery and use charger only.
CAUTION
Adjust Print Density
Manual Setting Adjust printing resolution manually.
In case of using Journal Media mode, Gap or BM calibration will not be displayed.
NOTE
Density Value: 1~9
8 9
4-2 Battery installation 4-3 Battery removal
Hook
As the battery is not charged at the time of your purchase, charge the
NOTE battery prior to using the printer
(Use Battery charger or Cradle to charge)
10 11
4-4 Battery charging 4-5 Roll paper installation
LED
1. Unless the exclusive charger is used provided by the manufacturer, the printer
NOTE can be damaged, and the manufacturer is not liable for the consequential damage.
2. Before removing the battery, make sure that power is turned off.
3. Printer does not work in the status of being connected with charger only.
4. The battery should be installed to operate printer.
5. While charging, do not turn on the power.
6. Do not operate the print while charging the battery.
7. Do not connect the charger while the printer is operated.
Pull a short length of paper out of the Tear off the additional paper using
printer and close the cover. tear bar.
12 13
4-6 Self test The sample of self test printout
Turn off the power pressing the While you are pressing the FEED
power button for approximately button, press the power button
3 seconds.
1 2
3
1. To print ASCII pattern additionally,
NOTE press the Feed button once more
After checking with self-test and no issues are found, you can examine other devices and
software. This function is working independently of devices and software.
The printout is produced.
Motor protection from being overheated
The motor should be stopped and cooled about more than 30 seconds after
continuous printing 1.5 meter
14 15
5. Peripherals Connection
This printer can communicate with peripheral devices via Bluetooth and 5-2 Interface cable connection
cables.
USB
16 17
6. Printer Specification
6-1 Specification
Size W X D X H(mm) 109 X 104 X 48.5
Printing Method Direct Thermal
W X D X H 4.29 X 4.09 X 1.9
Printing Speed Max. 70mm/sec
Weight 335g (with battery)
Resolution 203 DPI X 203 DPI
Temperature Operation -10 ~ 50
Character 9Type ( bitmap font)
Storage -20 ~ 60
Character set ALPHA NUMERIC Character, Extension
Character Humidity Operation 35 ~ 95%
Width 79.5mm0.5mm
Thickness 0.065~0.14mm
18 19