Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
To place an order click here --------- > Newage MX341 Replacement AVR
For our hompage click here ---------- > General Power Limited
For more information click here ----- > Newage Automatic Voltage Regulators
1. INTRODUCTION
Sensing Input Analogue Input
Voltage 190 ~ 264 VAC Max, 1 phase, 2 wire Max. Input 5 VDC
Frequency 50 / 60 Hz, nominal Sensitivity 1V for 5% generator volts
Input Resistance 1K ohm
Power Input (PMG)
Voltage 140 ~ 220 VAC Max, 3 phase 3 wire Quadrature Droop Input
Current 3A phase Burden 10 ohm
Frequency 100 ~ 120 Hz, nominal Max. sensitivity 0.07 A for 5% droop (PF=0)
Max. input 0.33 A
Output
Voltage Max. 120 VDC Over Voltage Detector Input
Current Continuous 2.7A Set point 300V. Time delay 1 Sec (fixed)
Intermittent 6A for 10 sec CB trip coil volts 10 ~ 30 VDC
Resistance Min. 15 ohm CB trip coil resistance 20 ~ 60 ohms
2. GENERAL DESCRIPTION
MX341 is a two phase sensed Automatic Voltage from the effects of nonlinear loads and to reduce
Regulator and forms part of the excitation system radio frequency interference on the generator
for a brush-less generator. Excitation power is terminals. Sustained generator short circuit current
derived from a three-phase permanent magnet is another feature of the PMG system.
generator (PMG), to isolate the AVR control circuits
______________________________________________________________________________________
2 NEWAGE MX341 AVR
The AVR senses the voltage in the main An analogue input is provided allowing
generator winding and controls the power fed to connection to a controller or other external
the exciter stator and hence the main rotor to devices with compatible output.
maintain the generator output voltage within the
The AVR has the facility for droop CT connection,
specified limits, compensating for load, speed,
to allow parallel running with other similarly
temperature and power factor of the generator.
equipped generators.
Soft start circuitry is included to provide a smooth
controlled build up of generator output voltage. NOTE :
______________________________________________________________________________________
NEWAGE MX341 AVR 3
If a replacement AVR has been fitted or re-setting of The UFRO adjustment is preset and sealed and
the VOLTS adjustment is required, proceed as only requires the selection of 50 or 60Hz and 4 pole
follows : or 6 pole, using the jumper link as shown in the
diagram. For optimum setting, the LED should
1. Before running generator, turn the VOLTS illuminate as the frequency falls just below nominal,
control fully anti-clockwise. i.e. 47Hz on a 50Hz system or 57Hz on a 60Hz
system.
2. Turn remote volts trimmer (if fitted) to midway
position.
4.4 DROOP Adjustment
3. Turn STABILITY control to midway position.
Generators intended for parallel operation are fitted
4. Connect a suitable voltmeter (0~300V ac) across
with a quadrature droop C.T. which provides a
line to neutral of the generator.
power factor dependent signal for the AVR. The C.T.
5. Start generator set, and run on no load at is connected to S1, S2 on the AVR, (see generator
nominal frequency e.g. 50~53Hz or 60~63Hz. wiring diagram for details). The DROOP adjustment
is normally preset in the works to give 5% voltage
6. If the red Light Emitting Diode (LED) is
droop at full load zero power factors. Clockwise
illuminated, refer to the Under Frequency Roll Off
increases the amount of C.T. signal injected into the
(UFRO) adjustment.
AVR and increases the droop with lagging power
7. Carefully turn VOLTS control clockwise until factor (cos ). With the control fully anti-clockwise
rated voltage is reached. there is no droop.
8. If instability is present at rated voltage, refer to
stability adjustment, then re-adjust voltage if 4.5 Trim Adjustment
necessary. An analogue input (A1 A2) is provided to connect
9. Voltage adjustment is now completed. to the controller or other devices. It is designed to
accept dc signals up to 5 volts.
4.2 Stability Adjustment The dc signal applied to this input adds to the
AVR sensing circuit. A1 is connected to the AVR
The AVR includes stability or damping circuit to
0 volts. Positive on A2 increases excitation.
provide good steady state and transient
Negative on A2 decreases excitation.
performance of the generator.
The TRIM control allows the user to adjust the
A jumper link selector is provided to optimize the
sensitivity of the input. With TRIM fully
response of the stability circuit to various size
anti-clockwise the externally applied signal has
generators.
no effect. Clockwise it has maximum effect.
The link should be positioned as shown in the
Normal setting is fully clockwise when used with
diagram according to the kW rating of the
a controller.
generator. The correct setting of the Stability
adjustment can be found by running the WARNING
generator at no load and slowly turning the
stability control anti-clockwise until the generator Any devices connected to this input must be
voltage starts to become unstable. The optimum fully floating and galvanically isolated from
or critically damped position is slightly clockwise ground, with an insulation capability of 500V
from this point (i.e. where the machine volts are ac. Failure to observe this could result in
stable but close to the unstable region). equipment damage.
______________________________________________________________________________________
4 NEWAGE MX341 AVR
4.6 Er Excitation (EXC) Adjustment 4.7 DIP Adjustment
This adjustment is set and sealed in the works and This feature is mostly used when the generator is
should not be tampered with. An over excitation coupled to turbo charged engines with limited block
condition is indicated by the illumination of the red load acceptance. The feature works by increasing
LED which also indicates under-speed running and the V/Hz slope to give greater voltage roll off in
over-volts. proportion to speed.
The generator must be stopped to reset an With the DIP control fully anti-clockwise, the
over-excitation trip. generator voltage will follow the normal V/Hz line as
the speed falls below nominal. Turning the DIP
control clockwise provides greater voltage roll off
aiding engine recovery.
MX341 AVR
Outline Drawing
Figure 1
______________________________________________________________________________________
NEWAGE MX341 AVR 5
k1-k2 linked for
normal operation.
K2 K1 P2 P3 P4 XX X 3 2 2 1
TRIM A1
A2
DROOP S1
S2
SENSING SELECTION
1
VOLTS 2
MX341 AVR 3
4
5
6
7
8
FREQUENCY
SELECTION
3 2 1 CBA
C-B 90KW~500KW
INDICATOR 3-1 4P/60HZ B-A OVER 550KW
LED 3-2 4P/50HZ
2-1 6P/50HZ
NO LINK 6P/50HZ
PMG
Exciter 3
Bridge
Generator 220V
R
G S
~ C.T
T
1K
For external adjusted
1K
P2 P3 P4 XX X 2 1 2 3 S1 S2
MX341 AVR
If the step above cant make the charger working still please contact with us.
______________________________________________________________________________________
6 NEWAGE MX341 AVR