ea017 {PAR CLI| SANSPIRE
3PAR CLI
@sanspire.com/3par-cli/
By sanaswati
Virtual Volumes/VLUN
Display virtual volumes (VVs) in the system
# show
Display virtual Luns in the system
# showlun
Display W to LD mapping
# showymap
Display W distribution across PDs
# showvpd
Display sets of Ws in the system
# showwset
Perform validity checks of virtual volume administrative
# checkw.
Drive Cage Management
How to locate a particular drive cage
# locatecage
How to set parameters for a drive cage
# setcage
Displays drive cage information
# showcage
Display block mapping info for ws/ids/pds
# showblock
Display logical disks (Id) information
# showld
Perform validity checks of data on logical disks
# checkid
Display LD to PD chunklet mapping
# showldch
Display LD to W mapping
# showldmap
Physical Disk Management
How to admit one or all physical disks to enable their use
# admi tpd
How to perform surface admit one or all physical disks to enable their use
# checkpd
How to spin a physical disk up or down
# controlpd
How to dismiss one or more physical disks from use
# diswisspd
How to move data from specified PD to a temp location selected by the system
# movepdea017 {PAR CLI| SANSPIRE
How to perform surface admit one or all physical disks to enable their use
# setpd
How to perform surface admit one or all physical disks to enable their use
# showpd
‘Show status of selected chunklets of physical disks
# showpdch
‘Show PD to WV mapping
# showpdvw
Display estimated free space
# showspace
Display spare and relocated chunklets
# showspare
Host related commands
To see hosts defined on the array
# showhost
# showhost. *loncdc2ce1234-a*
To see hostsets defined on the array
# showhostset
# showhostset *lonce1234*
To see WWNs that are not assigned to any hosts yet
# showhost -noname
Health/Alert/Event related commands
How to remove one or more alerts
# removealert
How to set the status of system alerts
# setalert
How to display system alerts
# showalert
How to display event logs.
# showeventlog
How to display the status of the system hardware and software components
# checkhealth
How to set the status of system alerts
# setalert
Licensing management commands
How to set the license key
# setlicense
How to display the license keys installed
# showlicense
‘System related commands
How to display firmware versions
# showfi rmwaredb
How to display date and time for all system nodes
# showdateea017 {PAR CLI| SANSPIRE
How to set date and time for all system nodes
# setdate
How to set the properties of node components such as serial number of power supply
# setnode
How to display overview of the node specific properties
# shownode
How to display node’s environment status
# shownodeenv
How to display EEPROM information of nodes
# showeepron
How to locate a particular node compoment by blinking LeDs on the node
# Tocatenode
How to locate a system by blinking its LeDs
# locatesys
How to set the system-wide parameters such as the raw space alert
How to display system properties such as name, model, serial number, capacity
Display system manager start up state
Display hardware inventory
Display patches applied to the system
Display software versions
# setsys# showsys# showsysmgr# showinventory# showpatch# showversion
Network Interface configuration
How to configure the network interface
How to display the network configuration
# setnet# shownet
Port related commands
How to perform loopback test on FC ports
# checkport
How to control FC or Remote copy ports
# controlport
How to set up the parameters and characteristics of an iscsI port
# controliscsiport
How to display the iscsr active sessions per port
# showiscsisession
How to display the iscst active sessions per port
# showiscsisession
How to display system port information
# showport
How to display ARP table for iSCSI ports in the system
# showportarp
How to display details information about devices on a FC port
How to display Link Error Status Block information about devices on a FC port
How to display unrecognized targets