Some tests may damage copier, USE AT YOUR OWN RISK! NOT for use with Sharp Digital Copiers
Press "Clear", "Interrupt", "0", "Interrupt".
OR "Clear, "0", "0", "Clear". OR "Clear", "Repeat", "0", "Pause".
Then enter Simulation # and press "Print" key to enter selected
simulation.
1: Drives scan/checks scan switches
2: Manually move scanner and check switches 3: Check paper path switches and in some machines cassette switches 4: Cassette switches 5: Lights up all display on panel 6. Heat lamp on/off 5 times 7: Light exposure lamp 8: Turns on bias voltage continuously 9: Turns on charge corona 10: Turns on transfer corona 11: Turns on discharge corona continuously 12: Turns on blank discharge lamp 13: Resets U1 14: Resets H3, H4, ect. 16: Check maintenance preset # 18: Check total count 19: Check copies since last PM 20: Reset PM counter to 0 21: Aging and check warmup 22: Aging without paper 23: Aging no worm up or misfeed 24: Instant ready 25: Developer stir/calibration 26: Check lens motion (1 cycle) 27: Check lens motion 30: Test ADF switches 31: Test ADF 33: Check ADF/RADF components. 0: Forward feed motor. 1: Reverse feed motor. 2: Forward transport motor. 3: Reverse transport motor. 4: Exit motor speed normal. 5: Exit motor speed slow. 6: Paper feed solenoid. 7: Reverse solenoid. 8: Stopper solenoid. 34: Test drum separator. 39: Adjust document sensing. 40: Reads developer preset 41: Reads copy # since developer change 42: Resets copies on developer 45: Drum setting. First value read is current to machine setting. Enter new # to match the highest # on front flange of drum. 46: Adjust exposure. Use # key to change settings. 47: AE setting. Scan half way. Read display. Press {Print} to change exposure lamp voltage settings in 5 volt increments. 48: Horizontal magnification. 49: Vertical magnification. 50: Lead edge registrations. Use# key to change setting. 54: Transport roller rimming. Use {Print} switch to change setting 57: Edge erase setting. Change with # keys. 58: Lead edge and void adjustments Use zoom keys. 60: Original detection adjustment. See service manual 63: Test duplicate sensors. Actuate sensor and watch display. 64: Sorter componets. 0: Solenoid 1: Motor 2: Gate 68: Test duplex componets. 0: Transport 1: Paper feed 2: Duplex / Overlay gate 3: Paper Stop Feed 4: Registration clutch 5: Alignment plate 6: Trail edge stopper 7: Duplex reverse solenoid 70: ADF total count. 71: Duplex total count. 75: Reset ADF count to 0. 76: Reset Duplex count to 0. 77: Lens rank. 78. Setting up auto clear and double cout for 11x17. CPOP 78 "Print". When "ready" lights, enter #, press "Print" to lock in ("Ready" will go off). 0: No auto clear; Double count on PM and total. 1: No auto clear; Double count on PM, single on total. 2: No auto clear; Signle count on PM, double on total. 3: No auto clear; Single count on PM and total. 40: Auto clear; Double count on PM and total. 41: Auto clear; Double count on PM, single on total. 42: Auto clear; single count on PM, double count on total. 43: Auto clear; Single count on PM and total. 79: Country setting. 8500 8800 Japan 14 4 Metric 15 5 Sharp Only 12 2 Inch (U.S.) 17 7 80: Setting options. 1: ADF only. 2: RADF only. 10: Duplex only. 11: ADF and Duplex. 12: RADF and Duplex. 20: 15 bin sorter only. 21: 15 bin sorter and ADF. 22: 15 bin sorter and RADF. 30: 15 bin sorter and duplex. 31: 15 bin sorter, ADF, duplex. 32: 15 bin sorter, RADF, duplex. 40: 20 bin sorter only. 41: 20 bin sorter and ADF. 42: 20 bin sorter and RADF. 50: 20 bin sorter and duplex. 51: 20 bin sorter, ADF, duplex. 52: 20 bin sorter, RADF, duplex, 94: Check and adjust orginial sensor. 95: 8500 Language display. English: RPM #1, set to "0". 97: send toner to transport.