Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
D E C A D E
A M P L I F I E R S D A 4 0 0 2 , D A 6 5 0 2 , D A 3 5 0 4 , D A 1 0 0 2
G E N U IN E JB L
DA OM 7/14/98 11:38 AM Page 2
2
DA OM 7/14/98 11:38 AM Page 3
1 7 9 6 8 6
8
2
2 1 7 9 7 1 2
5 4
3 3 5
4
20
20 AMP
+ LEFT RIGHT +
30
SPEAKER OUTPUT POWER
SPEAKER OUTPUT
2 1 7 9 8
Controls and Connectors
1. Pre-amp Line Level Input Connector
Connects to line-level output from the 5. Power Connector Connection for SPEAKER INPUT LINE INPUT INPUT LEVEL BASS EQ LOW PASS
FILTER
L
+
R+
R
R
L
L R
speaker level output from the source 7. Input-Level Control Adjusts input sen-
unit (2-channel on DA4002, DA6502, sitivity for pre-amp level and speaker 5
3 4
DA1002; 2 separate 2-channel connec- level inputs.
tors on DA3504). 8. Crossover Selector Determines
20 AMP
3. Speaker-Output Connector 2-channel whether the crossover is a High-Pass SPEAKER OUTPUT POWER FUSE
BRIDGED +
on DA4002, DA6502 and DA1002; 4- filter @120Hz (HP), a Low-Pass filter + LEFT RIGHT + REM GND() BATT(+) 20 AMP 20 AMP
20
20
4. Fuse DA4002: 15A ATC, pass filter frequency selector (DA1002).
DA6502: 20A ATC, DA1002 2x 20A ATC, 9. Bass E.Q. Enables bass boost +6dB
DA3504: 30A ATC. @ 50Hz. DA1002
3
DA OM 7/14/98 11:38 AM Page 4
4
DA OM 7/14/98 11:38 AM Page 5
5
DA OM 7/14/98 11:38 AM Page 6
Figure 1
L R R
15
15 AMP OFF +6dB LPF FLAT HPF
+ LEFT RIGHT + 1 10
L
SPEAKER OUTPUT POWER
Figure 2
Applications
For your convenience, weve included
several application diagrams to help you 20 AMP
L + R+
INPUT LEVEL BASS EQ LOW PASS
FILTER
20
20
OFF +6dB OFF 70Hz 100Hz
1 10
+ +
ure the Decade Series power amplifiers
L R
L
20
20 AMP 1 10
R
L
+
R
2-way speakers with the two front MONO STEREO
30
OFF +6dB LPF HPF LPF HPF OFF +6dB
STEREO 1 10 1 10
MONO
FLAT FLAT
L L
6
DA OM 7/14/98 11:38 AM Page 7
Troubleshooting
Use the following guide to identify
symptoms and solve problems. Make
sure the vehicles electrical system is
working properly and power is reaching
the amplifiers power connector.
Speakers are not connected Check wiring; use VOM/DVM to measure speaker coil
or are blown resistance
We, JBL Europe A/S
Kongevejen 194B
Distorted audio Input sensitivity is not set properly See Setting Input Sensitivity on page 5 DK-3460 Birkerd
DENMARK
Audio lacks punch Speakers are wired with Check polarity of connections; refer to Applications declare in own responsibility, that the products described
wrong polarity in this owners manual are in compliance with technical
standard:
Audio cycles off and on; A protection circuit is turning Verify the following: off electrical system is between EN 55 020/6.1988
amber protection LED amplifier off and on 5 ~ 18 Vdc; temperature is not over 194F (90C);
(JBL badge on top panel) no short circuits; speaker loads are not less than 2 ohms
is not lit (4 ohms in mono)
Audio cycles off and on; GAIN is set too high Set Input Sensitivity correctly (see page 5)
amber protection LED
(JBL badge on top panel) is not lit
Steen Michaelsen
JBL Europe A/S
Fuse blows Incorrect wiring or Check connections; refer to Applications Birkerd. DENMARK. 3/98
short circuit
7
DA OM 7/14/98 11:38 AM Page 8
Specifications
DA4002, DA6502, DA1002, DA3504