Sei sulla pagina 1di 15

STP TABLE OF CONTENTS

110

Section /Page Title

1 /2 Technical Data

2 /3 - 5 Construction and Design

3 /6 7 Dimensions Sheets
3.1 /6 Well Mounted Construction
3.2 /7 Elastic Well Mounted Construction

4 /8 Standard Installation Proposals


4.1 /8 Well and Elastically Well Mounted

5 /9 12 Steering Systems
5.1 /9 10 SST 502
5.2 /11 12 SST 602

6 /13 15 Hy-System
6.1 /13 General Hy-Diagram
6.2 /14 Hy-Pump
6.3 /15 Hy-Aggregate

Status Scale Alteration Index Drawing No. / Ident No. Section / Page
04/00 HDB1124 -/1
STP TWINPROPELLER FOR MAIN PROPULSION
110 POWER RANGE 130 260 kW

Technical Data

Max. input torque:

Service factor 1 0.90 0.75


Max. input torque 1050 Nm 945 Nm 787 Nm

Max. input speed : 2350 r.p.m.

Reduction:
Power transmission total : 2.68 :1
Power transmission upper gear : 1.65 :1
Power transmission lower gear : 1.625 :1
Steering transmission : 32 :1

Optimum propeller diameter

Input speed 1800 r.p.m. 2000 r.p.m. 2200 r.p.m. 2350 r.p.m.
Propeller diameter 800 mm 800 mm 750 mm 750 mm

Other Solutions available!

Min. propeller diameter : 700 mm


Max. propeller diameter : 800 mm

Propeller stem length:


PAL min. : 1050 mm
PAL max. : 3400 mm

Other solutions available!

Classification

Available

Status Scale Alteration Index Drawing No. / Ident No. Section / Page
04/00 HDB1125 1/2
STP CONSTRUCTION AND DESIGN
110

FORM OF CONSTRUCTION

The SCHOTTEL Twin Propeller type STP 110 designed in the form of a Z-drive is
available the version:

- Well-mounted type

The SCHOTTEL Twin Propeller (STP) is equipped with two propellers rotating in the
same direction.

DESIGN

The SCHOTTEL Rudderpropeller type STP 110 Z-version is consisting of the following
three main assemblies:

- Upper gearing with power and steering gear


- Intermediate section
- Lower gear with two propeller and two fins

Upper gearing

Housing: The housing is made of spheroidal graphite iron (GGG) of suitable quality and
pressure-tested and contains the bevel gear transmission for power and the gear
transmission for steering. It is topped by an expansion tank.

Gear wheels: The cyclo-palloid-type gear wheel/pinion are case-hardened and fine
machined after hardening.

Shafts: Input shafts are controlled by a back-stop device. It prevents trailing of the
propeller in the opposite direction.

Bearings: Bearings are all bearings of appropriate type.

Sealings: Shafts are sealed by lip-seals. Other parts are sealed by O-rings. Running
sleeves for lip-seals are ceramic-coated.

Intermediate section

Support tube: The stem section is supported by a tube-shaped housing which is the
relevant part of construction for the hull's framing.

Steering pipe: The steering pipe is the vertical connection between the steering gear
and the lower gear housing.

Power transmission shaft: Connection between the upper and lower gear's power
transmission is achieved by a vertical transmission pipe shaft, running inside the
steering pipe.

Status Scale Alteration Index Drawing No. / Ident No. Section / Page
05/00 HDB 2/3
STP CONSTRUCTION AND DESIGN
110

Lower gear

Housing: The lower gear box is manufactured from high quality cast iron GGG 40 and
contains the lower bevel gear. The lower gear is formed to give minimum resistance and
to achieve optimum propeller performance, the design of the lower gear housing incor-
porates SCHOTTEL's decades of knowhow.

Gear wheels: The pinion and wheel are of cyclo-palloid type. They are case-hardened
and fine machined after hardening. They are designed for max. continuous load under
consideration of additional safety factors and classification requirements.

Propeller shaft: All power-transmitting parts are manufactured from approved materials
accepted by the Classification Societies for transmitting the specified power.

Bearings: All bearings in the lower gear are of the roller type.

Sealings: The propeller shaft seal (triple) is of type Lip seal. The running sleeve is of
high-quality stainless steel material with ceramic coating. Non-rotating parts are sealed
by O-rings. The sealing arrangement is of a proven type.

Propeller: The propellers are of type Kaplan or Wageningen B-series, two or three-
bladed, depending on the results of the torsional vibration analysis. Standard propeller
material is CuAlNi.

DESIGN DETAILS

Steering system

The lower gearing with propellers can be infinitely moved towards port or starboard by
means of one hydraulic motor of type worm gear. The propeller thrust can be directed
endlessly through 360 around the vertical axis, as a result an optimum combination of
propulsion and steering is attained.

Lubrication

The STP 110 is lubricated by means of a combined splash/spray oil system.


The lower gearing and the steering worm gear are designed basing submersion
lubrication. The lubricating oil for the power transmission is forced through the oil
circulating worm into the lower gearing and rises through the hole in the power
transmission shaft into the lubricating oil tank.
The lubricating oil is cooled in the lower section by the water surrounding the STP.
The steering gear is sealed from the power transmission and is provided with a separate
oil filling.
The oil header tank including oil lever gage and warning device is mounted on top of the
upper gear box.

Status Scale Alteration Index Drawing No. / Ident No. Section / Page
05/00 HDB 2/4
STP CONSTRUCTION AND DESIGN
110

Recommended Lubricants

Amount
Brand Oil type
Agip Blasia 150
Aral Degol BG 150 (ISO)
BP Energol GR-XP 150
Castrol Alpha SP 150
Chevron Non Leaded Gear Compound 150
Esso Spartan EP 150
Fina Giran 150 (ISO)
Mobil Mobilgear 629
Shell Omala 150 (ISO)
Texaco Meropa 150
Wisura Kineta 150

The load stage for the oils of the STP drive must be above 12 of the FZG-test
A 8,3/90, acc. to DIN 51354.

Oil quantities

The quantity of oil depends on the stem-length "PAL".


Standard value (+/- 10 %) for the provision.

PAL (mm) 1000 1500 2000 2500 3000 3500


Oil quantity (l) 40 45 52 58 66 72

Status Scale Alteration Index Drawing No. / Ident No. Section / Page
05/00 HDB 2/5
BASIC PROGRAMME
STP TIME-DEPENDABLE ELECTRIC-HYDRAULIC
110 STEERING SYSTEM SST 502

Technical Data SST 502 STP 110

Reduction ratio steering SRP 32 : 1

Steering time Ca. 7 s/180

Supply voltage, AC-ripple < 1 V 24 V DC 20%

Hy-aggregate, oil capacity Ca. 44 l

Hy-oil type See recommended lubricants

Hy-oil flow approx. 24 l/min


nmin = 650 r.p.m.
Hy-pump nmax = 2200 r.p.m.
cm/r.p.m. = 45

For final size of electric cable and hydraulic pipes see electric and hydraulic diagrams.

The steering is actuated by a joy-stick-switch, which is automatically centred by a spring.


The switch transmits the electric steering impulses (port and starboard) via an electronic
circuit system, a hydraulic solenoid valve and hydraulic motor fitted out with a reduction
gear to the STP.

The steering motion is stopped when centring the joy-stick.

The thrust direction or rudder position is transmitted electrically to the indicator unit in the
steering panel. The transmitter is mechanically connected to the STP.

Status Scale Alteration Index Drawing No. / Ident No. Section / Page
04/00 HDB1132 5.1/9
BASIC PROGRAMME
STP WAY-DEPENDABLE ELECTRIC-HYDRAULIC
110 STEERING SYSTEM SST 602

Technical Data SST 602 STP 110

Reduction ratio steering SRP 32 : 1

Steering time ca. 7 s/180

Supply voltage, AC-ripple > 1 V 24 V DC 20%

Hy-aggregate, oil capacity ca. 44 l

Hy-oil type See recommended lubricants

Hy-oil flow approx. 24 l/min


nmin = 650 r.p.m.
Hy-pump nmax = 2200 r.p.m.
cm/r.p.m. = 45

For final size of electric cable and hydraulic pipes see electric and hydraulic diagrams.

A rudder position sender "Copilot 2000" gives the electric impulse to an electronic circuit
system, solenoid valve and hydraulic motor fitted out with a reduction gear to the STP.

The thrust direction or rudder position is transmitted electrically to the indicator unit
mounted in the steering panel. The transmitter is driven mechanically from the STP. The
hand-wheel of the Copilot is turned horizontally and sets the rudder or thrust angle.

The indicator follows until the set position has been reached.

In case of an electronic break-down or failure, the steering is automatically switched to a


time-dependable system. The vertical lever within the hand-wheel is used for clutch
actuation and speed control of the prime mover.

In case of failure of the main steering system, this is either switched over automatically or
manually (optionally) to a time-dependable steering system.

Status Scale Alteration Index Drawing No. / Ident No. Section / Page
04/00 HDB1133 5.2/11

Potrebbero piacerti anche