Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
MONOGRAM SYSTEMS
MONOGRAM SYSTEMS 1500 Glenn Curtiss Street
Carson, California 90746-1189 - USA
Tel: 310-884-7000 Fax: 310-884-7300 www.monogramsystems.com
SITA/LAXMOD CAGE Code: 29780
DISTRIBUTION STATEMENT
This document contains proprietary information of Monogram Systems, and it is issued in strict confidence. Except for
rights expressly granted by contract, this document may not, in whole or in part, be duplicated, reproduced, disclosed, or
used for design or manufacturing purposes without written authorization from Monogram Systems.
Page T-1
38-34-11 Dec 11/89
REVISION 12: Sep 14/09
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
HIGHLIGHTS
This is a PARTIAL revision. Pages which have been revised or added are outlined below
together with the highlights of this revision. For your convenience, all pages have been
reprinted with this document. Please remove and discard all pages. and initial and date the
RECORD OF REVISIONS page.
38-34-11
Pages:
103 Updated table to remove HP 6111A power supply and allow a wider
range of alternatives.
702 Updated 701 Table Assembly Materials, replaced adhesives No. 771
and No. 1993.
Page HLT-1
Monogram Proprietary See cover page for details 38-34-11 Sep 14/09
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page HLT-2
Monogram Proprietary See cover page for details 38-34-11 Sep 14/09
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
HIGHLIGHTS
This is a FULL revision. Pages which have been revised are outlined below together with
the highlight of the revision. Please remove and discard all pages. All pages have been
reprinted with this revision.
Pages:
3, 4 Removed PN 14403-130 from Leading Particulars.
Page HLT-1
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page HLT-2
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
HIGHLIGHTS
This is a FULL revision. Pages which have been revised are outlined below together with
the highlight of the revision. Please remove and discard all pages. All pages have been
reprinted with this revision.
Pages:
302, 303, 304 Revised pages to add disassembly procedures to reflect new PNs
added.
703 thru 708 Revised pages to add assembly procedures to reflect new PNs added.
Page HLT-1
Monogram Proprietary See cover page for details 38-34-11 Nov 30/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page HLT-2
Monogram Proprietary See cover page for details 38-34-11 Nov 30/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
HIGHLIGHTS
Pages which have been revised or added are outlined below together with the highlights of this
revision. This is a Partial revision. Please remove and discard affected pages of this manual and
date the RECORD OF REVISIONS page.
Chapter-Section-Unit/Page
Description of Change Effectivity
No.
Page HLT-1
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Chapter-Section-Unit/Page
Description of Change Effectivity
No.
Page HLT-2
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
RECORD OF REVISIONS
Page RR-1
Monogram Proprietary See cover page for details 38-34-11 Sep 14/09
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page RR-2
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page SBL-1
Monogram Proprietary See cover page for details 38-34-11 Jan 10/03
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page SBL-2
Monogram Proprietary See cover page for details 38-34-11 Jan 10/03
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page LEP-1
Monogram Proprietary See cover page for details 38-34-11 Sep 14/09
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page LEP-2
Monogram Proprietary See cover page for details 38-34-11 Sep 14/09
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
TABLE OF CONTENTS
INTRODUCTION .................................................................................................................. 1
1. General ...................................................................................................................... 1
2. Layout of Manual ....................................................................................................... 1
3. Revision Service ........................................................................................................ 1
4. Shop Verification........................................................................................................ 1
DESCRIPTION AND OPERATION ...................................................................................... 1
1. General ...................................................................................................................... 1
2. Description ................................................................................................................. 1
3. Operation ................................................................................................................... 2
4. Servicing .................................................................................................................... 2
5. Leading Particulars .................................................................................................... 3
TESTING AND FAULT ISOLATION ................................................................................ 101
1. General .................................................................................................................. 101
2. Testing ................................................................................................................... 101
3. Trouble Shooting.................................................................................................... 110
DISASSEMBLY................................................................................................................ 301
1. General .................................................................................................................. 301
2. Procedure .............................................................................................................. 301
CLEANING ....................................................................................................................... 401
1. General .................................................................................................................. 401
CHECK............................................................................................................................. 501
1. General .................................................................................................................. 501
2. Procedure .............................................................................................................. 501
REPAIR ............................................................................................................................ 601
1. General .................................................................................................................. 601
2. Equipment and Materials ....................................................................................... 601
3. Procedure .............................................................................................................. 601
ASSEMBLY...................................................................................................................... 701
1. General .................................................................................................................. 701
2. List of Materials...................................................................................................... 702
3. Procedures............................................................................................................. 702
4. Storage Instructions ............................................................................................... 708
FITS AND CLEARANCES ............................................................................................... 801
SPECIAL TOOLS, FIXTURES, AND EQUIPMENT ......................................................... 901
1. Special Tools ......................................................................................................... 901
2. Test Equipment...................................................................................................... 901
Page TC-1
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page TC-2
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
LIST OF FIGURES
Page TC-3
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
LIST OF TABLES
Page TC-4
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
INTRODUCTION
1. General
This document is issued to provide instructions to maintain, troubleshoot and test the
waste tank assembly, liquid level sensor and liquid level transmitter used on the
aircraft vacuum waste system.
2. Layout of Manual
The information in this manual is divided into sections in accordance with Air
Transportation Association, specification 100 to enable maintenance personnel to
disassemble, clean, check, repair, assemble, troubleshoot and test the unit. An
illustrated parts list is provided to locate, identify and requisition parts.
3. Revision Service
4. Shop Verification
The sections within this manual have been verified at the manufacturers facility by
actually performing the functions such as disassembly, assembly, and testing.
INTRO-1
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
INTRO-2
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
1. General
System component covered in this manual are employed for collection and disposal of
waste. A liquid level sensor and a liquid level transmitter provide indications of the
amount of waste in the tank to the system controller. The water separator removes
moisture and solid particles from air venting from the tank. The tank incorporates
provisions for draining and cleaning during ground service operation.
2. Description
Page 1
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
3. Operation
A. Waste is received into the tank through two waste inlets on the upper portion of
the tank. Mounted within the tank, just below the inlet point is a short S shaped
pipe configuration with a gradually increasing I.D. This section of the inlet tubing
is designed to slow down and absorb any impact from fast moving hard objects
and direct air and waste toward the center of the tank to protect tank walls and
minimize foam.
B. The liquid level sensor provides an indication signal to the system controller
when fluid in the tank reaches its usable capacity.
The control unit of the sensor generates an electrical signal that is converted to
an ultrasonic signal at the transmitter transducer. When the gap is filled with a
fluid medium, this signal is transmitted across the sensor gap to the receiver and
reconverted to an electrical signal. The signal amplified and converted to a
voltage providing a low output (0 to 3.5 VDC) when the sensor detects fluid and a
high output (over 18 VDC) when the sensor is dry.
C. The liquid level transmitter measures the pressure of the water above the
transducer, independent of ambient pressure. This measurement is continuously
transmitted to the system controller, where it is translated to an indication of
current tank content and sent to the aircrafts forward attendant panel.
D. The dual level sensor performs the duties of both the liquid level sensor and the
liquid level transmitter, and is a replacement for same. Mounted in the upper
inlet, the sensor supplies the identical signals to the aircrafts forward attendant
panel.
E. The water separator removes all trapped moisture, foam and shredded paper
from the air flowing from the waste holding tank to the overboard vent. The air-
liquid mixture will assume a rotary path of travel within the separator, causing the
moisture particles to separate from the air.
F. During ground serving and after draining of the tank, the rinse assembly fitting
direct water from ground service facilities against interior tank walls.
4. Servicing
The waste holding tank must be serviced after each scheduled flight by draining and
rinsing the tank. This step must be performed properly to prevent waste build-up and
subsequent system performance deterioration. Damage to system components may
result from improper servicing.
Page 2
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
5. Leading Particulars
Page 3
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 4
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 5
Monogram Proprietary See cover page for details 38-34-11 Nov 30/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 6
Monogram Proprietary See cover page for details 38-34-11 Nov 30/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
1. General
This section of the manual describes the equipment and procedures for testing and
fault isolation of the Waste Tank Assembly, Liquid Level Sensor, Liquid Level
Transmitter and Water Separator.
2. Testing
Page 101
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
VACUUM PRESSURE
GAUGE GAUGE
VENT 0-30 Hg 0-30 PSI
TO ATM (0-762 mm) Hg (0-2,7 Bars)
* *
PRESSURE
SOURCE
(AIR)
VACUUM
SOURCE
TANK ASSEMBLY
P/N 14403-001
P/N 14403-107
Test Setup
Figure 101
Figure 101: Test Setup
Page 102
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 103
Monogram Proprietary See cover page for details 38-34-11 Sep 14/09
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 104
Monogram Proprietary See cover page for details 38-34-11 Sep 14/09
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
(3) Procedure
(a) With chamber at room temperature, increment applied vacuum to the
liquid level transmitter reference port and verify that output current is
within the ranges noted below:
Applied Vacuum
Output Current
(milliamps)
PSI (Bars)
Applied Vacuum
Output Current
(milliamps)
PSI (Bars)
Page 105
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
(c) Repeat step (b) with chamber at 131 2.5F (55 1.4C).
NOTE: The resulting output current of the above tests will be
identical if a positive pressure is applied to the liquid level
transmitter sensing diaphragm.
(d) The insulation resistance between power input and case, as well as
power return and case shall be 1 Mohm or greater using DVOM. If the
readings are lower than 1 Mohm, reverse DVOM lead polarity and test
again.
Page 106
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 107
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 108
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 109
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
3. Trouble Shooting
The following trouble shooting procedures deal with problems encountered during
testing of the Waste Tank, Liquid Level Sensor, Liquid Level Transmitter and the
Water Separator; refer to Troubleshooting Table 102.
Waste Tank
Leaks at joints and/or connections Worn or deteriorated seals Replace seals, o-rings,
gaskets as necessary to stop
leakage
Water separator
Water drops are visible in view Faulty basic separator Replace basic separator
tube during test
Page 110
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
DISASSEMBLY
1. General
2. Procedure
Page 301
Monogram Proprietary See cover page for details 38-34-11 Jan 10/03
30/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
(3) Remove polar covers (1A-20 or 20A or 20B) by removing screws (1A-30).
(4) Remove and discard O-ring (1A-40 or 40A or 40B).
(5) Do not remove insets (1A-50 or 50A) or studs (1A-60 or 60A), (1A-70 or
70A) or (1A-80 or 80A) unless damaged.
(6) If damaged or illegible, remove labels (1A-140 or 140A and 1A-150).
Page 302
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
D. Remove and disassemble Water Separator Assembly (refer to IPL Figure 4):
(1) Remove water separator assembly (1-20 or 20A) by removing V-retainer
clamp
(1-30). Remove and discard O-ring (1-40).
(a) Remove filter housing assembly (20 or 20A) and basic separator (10)
from waste tank.
(b) If damaged, remove gasket (15) from basic separator (10).
(c) Disassemble filter housing assembly (20 or 20A) as follows:
1 Remove cover (30 or 30A or 30B) by removing screws (40) and
washers (50). Remove and discard O-ring (60 or 60A).
2 Remove and discard retaining ring (85) if necessary.
3 Remove filter (70) from filter holder (80).
NOTE: Filter holder (80), case (90 or 90A) and mounting
ring (100) and filter holder (80) and filter
housing/mounting ring assembly (102) are bonded
together. Do not disassemble unless either of these
parts are damaged and need replacement.
4 If damaged or illegible, remove label (125 or 125A).
Page 303
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
E. Remove and disassemble Water Separator Assembly (refer to IPL Figure 4A):
(1) Remove filter housing assembly (20) by removing screws (30) and washers
(35) from housing filter (75).
(2) Remove ring (25), cover (40), O-ring (45), filter (50), and holder (55) from
housing filter (75).
(3) Remove separator basic assy (80) by removing nuts (70), and washers (65).
(4) Remove gasket neoprene (85), and remove top flange (90) by removing
rivets (95, 110) and washers (115) from cone assy (105) and cylinder inner
assy (120).
Page 304
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
CLEANING
1. General
Page 401
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
(d) Leave the solution in the tank assembly over night, or for and extended
period of time. When soaking is concluded, drain all liquid from the
tank assembly and rinse thoroughly.
(e) Disconnect the fill and drain lines from the Cleaning Cap, and remove
the cap from the tank assembly.
(f) Install the water separator assembly (20 or 20A) on the tank
assembly per ASSEMBLY instructions.
Page 402
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
CHECK
1. General
2. Procedure
A. Waste Tank
(1) Check parts for general condition, structural failure, damage and wear.
(2) Check O-ring sealing surfaces and O-ring grooves for evidence of damage,
nicks, cracks or stripping.
(3) Check sealing surfaces for evidence of damage nicks or stripping.
(4) Check threaded studs and inserts for loosening and cracking. Check
threads for stripping or cross threading. Replace studs as necessary in
accordance with repair.
(5) Check inside of tank for evidence of damage, cracking and unbonded areas,
especially between the liner and the carbon-reinforced plastic.
(6) Check entire exterior surface of tank for evidence of excessive mechanical
damage, i.e. abrasion, scratches, or severe puncture damage.
(7) Check tank axial restraint pad for mechanical damage and delaminated
areas.
Page 501
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
B. Water Separator
Check for dents, corrosion, cracks, scratches, excessive contamination or
deformations. Visually inspect gasket on basic separator (10, IPL Figure 4) for
tears or gouges. Replace as necessary in accordance with REPAIR.
Inspect filter housing mounting ring (100, IPL Figure 4) for cracks, chips, and
loose screws.
Discard any mounting ring (4-100) failing check. Item is not repairable.
Page 502
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
REPAIR
1. General
A. Except for permissible repairs outlined in this section, repair of the waste tank
assembly, water separator, liquid level sensor and liquid level transmitter is not
considered practical. Parts which do not meet inspection or functional
requirements shall be replaced. In addition to permissible repairs and
replacement of defective parts, certain parts replacement shall be routine at each
overhaul regardless of apparent condition of the part. All nuts, washers, gasket,
O-rings and filters removed during disassembly shall be replaced regardless of
apparent condition.
NOTE: Replace all damaged or otherwise illegible part number
identification.
Page 601
Monogram Proprietary See cover page for details 38-34-11 Sep 14/09
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 602
Monogram Proprietary See cover page for details 38-34-11 Sep 14/09
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
3. Procedure
Page 601
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
3 Cut carbon fiber fabric to desired shape and size. The total
thickness of plies should correspond with the maximum wall
thickness.
4 Note that the wall is reinforced with rowings running in two
directions (criss-cross). When the plies are applied to the wall
they are to be oriented so that the warp fibers in the bottom ply
are parallel with the rovings in one direction and the warp fibers of
the second ply are parallel with rovings in the other direction.
Continue in this same manner, alternating the direction of the
warp fibers of each successive ply.
5 Laminate with epoxy resin mixed with 25 percent by weight epoxy
hardener.
6 Rub out air and excess resin to smooth finish.
7 Allow epoxy to cure 24 hours at room temperature 70 F (21 C).
8 Grind edge of repair laminate to blend into tank surface.
9 Coat surface according to paragraph (c).
(c) If there is damage to fire protection coating.
1 Grind surface of damaged area with sandpaper to the ground of
carbon fiber plastic until uniformly roughened.
2 Paint or spray up the fire protection coating to a thickness of
0.008 in (0,2mm).
3 Allow to dry 24 hours at room temperature 70 F (21 C).
B. Water Separator
If bonded gasket on basic separator (10, IPL Fig. 4) is damaged, replace in
accordance with procedure below.
(1) Scrape to remove gasket. Take care not to cut or gouge gasket mounting
surface of flange.
(2) Generously coat gasket-mounting surface of flange with gasket sealant
compound.
(3) Bond gasket (15, IPL Fig. 4) to top flange.
Page 604
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 605
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 606
Monogram Proprietary See cover page for details 38-34-11 Sep 14/09
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 607
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 608
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
ASSEMBLY
1. General
A. Assembly instructions given herein presume the waste tank assembly has been
disassembled to the extent covered in DISASSEMBLY. All part number
identification removed during cleaning or otherwise illegible has been replaced
during repair. All new parts are identical in fit and function to the parts they
replace.
B. If a unit has been subjected to partial overhaul only, disregard those instructions
that are not applicable. Refer to Table 701 for assembly materials. The
assembly instructions detailed in the following paragraphs apply equally to those
assemblies listed in the paragraph heading unless reference is made in the
instructions to a specific assembly or assemblies. Where two or more details
may be installed at a particular location, the key index numbers of the parts, as
assigned in the Illustrated Part List, are included parenthetically after the part
description. Hardware items like bolts, washers, nuts and parts made of rubber,
removed during disassembly, should be replaced with new parts.
Page 701
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
2. List of Materials
3. Procedures
Page 702
Monogram Proprietary See cover page for details 38-34-11 Sep 14/09
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 703
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
(3) Apply thin coat of MOLYKOTE 111 Compound to bottom surface of spanner
nuts (60). While supporting diverters (80 or 80A and 90 or 90A) from
inside the tank, install spanner nuts (60) with spanner nut washer (70) and
tighten hand tight.
(4) Continue to support flow diverters form inside the tank and tighten spanner
(60) nuts three quarters turn using a spanner nut wrench.
(5) Slide clamping rings (40) or base rings (55) onto waste inlets (10). Install
clamping rings or base rings and inlets with new O-rings (50 or 50A) in
position on spanner nut studs.
(6) Secure clamping rings (40) or base rings (55) using washers (30) and nuts
(20 or
-20A or -20B). Torque to 44 in-lbs (5,0 Nm). Install safety wire (-100) using
MS33540 double twist method.
(7) Slide compression rings (40A) onto waste inlets (10) and position onto base
rings (55), secure rings with V-clamp (35).
Page 704
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
(4) Install nozzle (30) with Teflon washers (50) onto inlet fittings (10 and 10A)
and secure with retaining ring (60) and cotter key (70) if applicable.
(5) Install rinse assemblies (1A-90 and 1A-90A) with new O-ring (1A-120 or 1A-
120A). Secure using washers (1A-110) and nuts (1A-100 or 1A-100A).
Torque to 9 in-lbs (1,0 Nm).
Page 705
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
F. Assemble and install Water Separator Assembly (refer to IPL Figure 4):
(1) If moved install new label (125 or 125A).
(2) If removed during disassembly, bond gasket (15) to top flange of basic
separator (10) using adhesive (No. 1993).
(3) If required assemble new filter housing mounting ring (100) as follows:
(a) Place washer (AN960C8) on screw (8-32UNCX1-2).
(b) Insert screw into hole in mounting ring. Insure screw and washer are
flush with bottom of hole.
(c) Fill cavity with EC-1838 adhesive epoxy.
NOTE: Do not allow adhesive epoxy to rise above rim of cavity.
(d) Allow adhesive epoxy to cure per manufacturers instructions. If
required, grind adhesive epoxy flush with cavity.
(4) Assemble Filter Housing Assembly (20 or 20A) as follows:
(a) For filter housing Assembly PN 14401-030.
1 Fill (2) grooves in mounting ring (100) with sealant (EC-1239
B/A).
2 Align screws in mounting ring (100) with holes in care (90 or
90A) and install case onto mounting ring.
3 Apply sealant (EC-1239 B/A) to lower face of filter holder (80)
where holder mates to case (90 or 90A).
4 Align screws in mounting ring (100) with holes in filter holder (80)
and install holder (80) and install holder into case (90 or 90A).
Secure mounting ring, case and holder with washers (120) and
nuts (110). Torque to 15 in-lbs (1,7 Nm).
(b) For Filter Housing Assembly PN 14401-065.
1 Align screws (105) with holes in filter housing/mounting ring
assembly (102) and case (90 or 90A).
2 Apply sealant (EC-1239 B/A) to lower face of filter holder (80)
where holder mates to filter housing/mounting ring assembly
(102).
3 Align screws (105) with holes in filter holder (80) and install holder
(80) and install holder into filter housing/mounting ring assembly
(102).
4 Secure filter housing/mounting ring assembly and holder with
washers (120) and nuts (110). Torque to 15 in-lbs (1,7Nm).
Page 706
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 707
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
4. Storage Instructions
Page 708
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Not Applicable
Page 801
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 802
Monogram Proprietary See cover page for details 38-34-11 Nov 30/01
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
1. Special Tools
Page 901
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 902
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
1. Introduction
A. Purpose
This section lists, describes, and illustrates all component assemblies,
subassemblies, and detail parts. It is comprised of illustration sheets and detailed
parts lists (DPLs). Illustration sheets show exploded views and detailed parts
lists are arranged in a tabular form providing information about each item. Parts
listed are considered to be replaceable for reasons of wear, age, or excessive
abuse.
Page 1001
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
The Detail Parts List is arranged in a general sequence of disassembly. The parts are
illustrated in an exploded-view illustration and given in the related parts list.
A. FIG. ITEM Column
This column contains the number referenced in the illustration for each part. The
figure number is further specified as follows:
(1) The first number at the top of each FIG. ITEM column is the figure number
of the corresponding illustration.
(2) The remaining numbers are item numbers that correspond to the numbers
in the referenced illustration, and refer to a particular part that is detailed on
the corresponding row.
(3) A dash or hyphen (-) in front of an item number means the part is not
illustrated.
(4) Alpha-variant suffixes A through Z (except I and O) are assigned to item
numbers when necessary to identify:
* Similar parts differentiated by an effectivity code,
* Added parts,
* Alternate parts, or
* Service bulletin modified parts.
A check of the NOMENCLATURE column and the EFF CODE column will
clarify the usage or relationship of that part to the other parts.
Page 1002
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
C. NOMENCLATURE Column
This column contains descriptive information for each part, and may also list:
* the true part number (if longer than 15 digits or modified per ATA 200/2000),
* the vendor code (if the part was not manufactured by Monogram Systems),
* service bulletins affecting the part,
* obsolete part numbers,
* information regarding the interchangeability of parts, and
* other special terms and symbols.
Page 1003
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
ATTACHING PARTS
. Attaching Parts for Subassembly to End Item or Major Assembly
***
Page 1004
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 1005
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 1006
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 1007
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 1008
Monogram Proprietary See cover page for details 38-34-11 Nov 12/04
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
The CAGE code for the manufacturers of parts, materials, and equipment referenced
in this CMM are given below. The codes are taken from Cataloging Handbook H4-1.
The absence of a code in the NOMENCLATURE column of the Detail Parts List
indicates the part is manufactured or modified by Monogram Systems (29780).
Page 1009
Monogram Proprietary See cover page for details 38-34-11 Sep 14/09
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
AN960C8 4 120 16
AN960C8 4 -120A 8
DIN3771 1A -40B 2
MS20995C 3 -100 AR
MS24665-153 2 70 1
MS51957-46 4 40 12
MS9021-035 1 -120A 1
MS9021-143 1 -80A 1
NAS1102E06-4 1A 30 AR
NAS1291C3M 3 -20B 16
NAS1523C08Y 4 50 12
NAS620C10L 3 30 AR
NAS620C6L 1 110 6
NAS620C6L 1 70 8
NAS620C6L 1A 110 AR
NAS679C06 1 100 6
NAS679C06 1 60 8
NAS679C06 1A 100 AR
NAS679C06M 1A -100A AR
NAS679C08 4 110 8
NAS679C3 3 20 16
NAS679C3M 3 -20A 16
01017870 1A -20A 2
01017890 1A -50A AR
01017895 1A -40A 2
01017902 1A -80A AR
01017903 1A -70A AR
01017904 1A -60A AR
05967 1A 80 AR
05968 1A 60 AR
05970 1A 20 2
05983 1A 40 2
05984 1A 50 AR
06026 1A 70 AR
10369BZ8000 1A -20B 2
14312-011-3 1 30 1
14312-011-5 3 35 2
14400-354 1A 150 1
14400-354 5 20 1
14401-005 1 20 1
14401-005 4 -1 RF
14401-025 4 90 1
14401-025-1 4 -90A 1
14401-026 4 100 1
14401-027 4 30 1
14401-027-1 4 -30A 1
14401-028 4 80 1
14401-029 4 70 1
14401-030 4 -20 1
14401-043 4 15 1
14401-044 4 10 1
14401-046 4 85 1
14401-051 4 125 1
14401-052 4 130 1
14401-055 4 -125A 1
14401-060 1 -20A 1
14401-060 4 -1A RF
14401-062 4 -30B 1
14401-064 4 -125B 1
14401-065 4 -20A 1
14401-066 4 -85A 1
14401-067 4 102 1
14401-068 4 135 1
14401-085 1 -20B 1
14403-001 1 -10 RF
14403-001 1 -10A RF
14403-001 1 -10B RF
14403-001 1A -1 RF
14403-001 1A -1A RF
14403-001 1A -1B RF
14403-001NP 1 -1 RF
14403-002 1A 10 1
14403-003 1 90 1
14403-003A 1 -90A 1
14403-003B 1 -90B 1
14403-003B 5 -1 RF
14403-003B1 5 50 1
14403-003C 1 -90C 1
14403-003C 5 -1A RF
14403-003C1 5 -50A 1
14403-004 1 50 1
14403-005 3 80 1
14403-007 3 10 2
14403-007NP 1A 130 1
14403-007NP 3 -1 RF
14403-007NP 3 -1A RF
14403-008 3 90 1
14403-009 1A 90 1
14403-009 2 -1 RF
14403-010 1A 90A 1
14403-010 2 -1A RF
14403-011 5 10 1
14403-014 1A 140 1
14403-015 2 10 1
14403-016 2 -10A 1
14403-026 2 40 1
14403-027 2 20 1
14403-028 3 60 2
14403-030 3 40 2
14403-031 3 70 2
14403-056 2 30 1
14403-081 3 40A 2
14403-082 3 55 2
14403-085 1 -50A 1
14403-091 3 -80A 1
14403-092 3 -90A 1
14403-107 1 -10C RF
14403-107 1 -10D RF
14403-107 1A -1C RF
14403-107 1A -1D RF
14403-108 1A -140A 1
14403-130 1 -10E RF
14403-200 5 30 1
2-012N602-70 5 40 1
2-029N497-70 1A 120 2
2-029N602-70 1A -120A 2
2-035N497-70 1 120 1
2-037N497-70 1 80 1
2-152N497-70 3 50 2
2-152N602-70 3 50A 2
2-175N497-70 4 60 1
2-175N602-70 4 -60A 1
2-266N497-70 1 40 1
2-266N602-70 1 -40A 1
4812-107 2 50 2
5105-37H 2 60 1
8-32UNC 4 105 8
Page 1014
Monogram Proprietary See cover page for details 38-34-11 Nov 30/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
ATTACHING PARTS
30 14312-011-3 . CLAMP, V-RETAINER 1
***
ATTACHING PARTS
60 NAS679C06 . NUT 8
70 NAS620C6L . WASHER 8
***
ATTACHING PARTS
100 NAS679C06 . NUT 6
110 NAS620C6L . WASHER 6
***
90 100 110
120
130 30
50
60 20
40
90A
120
140
150
40 10
20
50
80
50
30 70
Page 1018
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
IPL Figure 1A: Waste Holding Tank Assembly - Detail Parts List
AIRLINE UNITS
FIG. EFF
STOCK NOMENCLATURE PER
ITEM PART NUMBER CODE
NO. 1234567 ASSY
1A___
ATTACHING PARTS
30 NAS1102E06-4 . . SCREW AR
***
IPL Figure 1A: Waste Holding Tank Assembly - Detail Parts List
AIRLINE UNITS
FIG. EFF
STOCK NOMENCLATURE PER
ITEM PART NUMBER CODE
NO. 1234567 ASSY
1A___
40 05983 . . O-RING A 2
(REPLD BY ITEM 40A)
-40A 01017895 . . O-RING (VS3708) B 2
(REPLS ITEM 40)
(REPLD BY ITEM 40B)
-40B DIN3771 . . O-RING C,D,E 2
(REPLS ITEM 40A)
50 05984 . . INSERT A AR
(REPLD BY ITEM -50A)
-50A 01017890 . . INSERT (VS3708) AR
(REPLS ITEM 50)
60 05968 . . STUD A AR
(REPLD BY ITEM 60A)
-60A 01017904 . . STUD (VS3708) AR
(REPLS ITEM 60)
70 06026 . . STUD A AR
(REPLD BY ITEM 70A)
-70A 01017903 . . STUD (VS3708) AR
(REPLS ITEM 70)
80 05967 . . STUD A AR
(REPLD BY ITEM 80A)
-80A 01017902 . . STUD (VS3708) AR
(REPLS ITEM 80)
ATTACHING PARTS
100 NAS679C06 . NUT A AR
(REPLD BY ITEM 100A)
-100A NAS679C06M . NUT B,C,D, AR
(REPLS ITEM 100) E
110 NAS620C6L . WASHER AR
***
IPL Figure 1A: Waste Holding Tank Assembly - Detail Parts List
AIRLINE UNITS
FIG. EFF
STOCK NOMENCLATURE PER
ITEM PART NUMBER CODE
NO. 1234567 ASSY
1A___
Page 1022
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
35
20B
30 (REF)
40A
55
10 (REF)
10
50A
20
30
40
50
60
90 70
(FIG. 1A-10)
(REF)
80
Page 1024
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
40
50
30
60
85
70
110
120 135
20
80
125
90
10
130
100
102
105
Page 1026
Monogram Proprietary See cover page for details 38-34-11 Sep 14/09
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 1028
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06
MONOGRAM SYSTEMS
COMPONENT MAINTENANCE MANUAL with ILLUSTRATED PARTS LIST
PN 14401 AND 14403
Page 1030
Monogram Proprietary See cover page for details 38-34-11 Dec 15/06