Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Commands Reference
This document provides two different ways of navigating ACLI command documentation.
alphabetically Each command is listed corresponding to the first letter of the command.
command mode Each command mode page has a list of commands that are available in that mode. Each page is organized
alphabetically for those commands in that mode.
Use the 'find-in-page' function of the browser to search for a command based on the page you are viewing. Most browsers launch
'find' using CTRL+F.
Notice
While reasonable efforts have been made to ensure that the information in this document is complete and accurate at the time of
printing, Avaya assumes no liability for any errors. Avaya reserves the right to make changes and corrections to the information in
this document without the obligation to notify any person or organization of such changes.
Documentation disclaimer
Avaya shall not be responsible for any modifications, additions, or deletions to the original published version of this documentation
unless such modifications, additions, or deletions were performed by Avaya. End User agree to indemnify and hold harmless
Avaya, Avaya's agents, servants and employees against all claims, lawsuits, demands and judgments arising out of, or in
connection with, subsequent modifications, additions or deletions to this documentation, to the extent made by End User.
Link disclaimer
Avaya is not responsible for the contents or reliability of any linked Web sites referenced within this site or documentation(s)
provided by Avaya. Avaya is not responsible for the accuracy of any information, statement or content provided on these sites and
does not necessarily endorse the products, services, or information described or offered within them. Avaya does not guarantee
that these links will work all the time and has no control over the availability of the linked pages.
Warranty
Avaya provides a limited warranty on this product. Refer to your sales agreement to establish the terms of the limited warranty. In
addition, Avayas standard warranty language, as well as information regarding support for this product, while under warranty, is
available to Avaya customers and other parties through the Avaya Support Web site: http://www.avaya.com/support. Please note
that if you acquired the product from an authorized Avaya reseller outside of the United States and Canada, the warranty is
provided to you by said Avaya reseller and not by Avaya.
License types
THE SOFTWARE LICENSE TERMS AVAILABLE ON THE AVAYA WEBSITE, HTTP://SUPPORT.AVAYA.COM/LICENSEINFO/ARE
APPLICABLE TO ANYONE WHO DOWNLOADS, USES AND/OR INSTALLS AVAYA SOFTWARE, PURCHASED FROM AVAYA INC., ANY
AVAYA AFFILIATE, OR AN AUTHORIZED AVAYA RESELLER (AS APPLICABLE) UNDER A COMMERCIAL AGREEMENT WITH AVAYA
OR AN AUTHORIZED AVAYA RESELLER. UNLESS OTHERWISE AGREED TO BY AVAYA IN WRITING, AVAYA DOES NOT EXTEND
THIS LICENSE IF THE SOFTWARE WAS OBTAINED FROM ANYONE OTHER THAN AVAYA, AN AVAYA AFFILIATE OR AN AVAYA
AUTHORIZED RESELLER, AND AVAYA RESERVES THE RIGHT TO TAKE LEGAL ACTION AGAINST YOU AND ANYONE ELSE USING
OR SELLING THE SOFTWARE WITHOUT A LICENSE. BY INSTALLING, DOWNLOADING OR USING THE SOFTWARE, OR
AUTHORIZING OTHERS TO DO SO, YOU, ON BEHALF OF YOURSELF AND THE ENTITY FOR WHOM YOU ARE INSTALLING,
DOWNLOADING OR USING THE SOFTWARE (HEREINAFTER REFERRED TO INTERCHANGEABLY AS "YOU" AND "END USER"),
AGREE TO THESE TERMS AND CONDITIONS AND CREATE A BINDING CONTRACT BETWEEN YOU AND AVAYA INC. OR THE
APPLICABLE AVAYA AFFILIATE ("AVAYA").
Copyright
Except where expressly stated otherwise, no use should be made of materials on this site, the Documentation(s) and Product(s)
provided by Avaya. All content on this site, the documentation(s) and the product(s) provided by Avaya including the selection,
arrangement and design of the content is owned either by Avaya or its licensors and is protected by copyright and other
intellectual property laws including the sui generis rights relating to the protection of databases. You may not modify, copy,
reproduce, republish, upload, post, transmit or distribute in any way any content, in whole or in part, including any code and
software. Unauthorized reproduction, transmission, dissemination, storage, and or use without the express written consent of
Avaya can be a criminal, as well as a civil, offense under the applicable law.
Third-party components
Certain software programs or portions thereof included in the Product may contain software distributed under third party
agreements ("Third Party Components"), which may contain terms that expand or limit rights to use certain portions of the
Product ("Third Party Terms"). Information regarding distributed Linux OS source code (for those Products that have distributed
the Linux OS source code), and identifying the copyright holders of the Third Party Components and the Third Party Terms that
apply to them is available on the Avaya Support Web site: avaya.com/support/Copyright/.
Trademarks
The trademarks, logos and service marks (Marks) displayed in this site, the documentation(s) and product(s) provided by Avaya
are the registered or unregistered Marks of Avaya, its affiliates, or other third parties. Users are not permitted to use such Marks
without prior written consent from Avaya or such third party which may own the Mark. Nothing contained in this site, the
documentation(s) and product(s) should be construed as granting, by implication, estoppel, or otherwise, any license or right in
and to the Marks without the express written permission of Avaya or the applicable third party.
Technical support
Avaya provides a telephone number for you to use to report problems or to ask questions about your product. The support
telephone number is 1-800-242-2121 in the United States. For additional support telephone numbers, see the Avaya Web site:
avaya.com/support.
If you purchased a service contract for your Avaya product from a distributor or authorized reseller, contact the technical support
staff for that distributor or reseller for assistance.
Documentation support
For the most current versions of documentation, see the Avaya Support Web site: avaya.com/support.
A
accept adv-rtr
accept adv-rtr enable
access-diffserve
access-policy
access-policy access-restrict
access-policy by-mac
access-policy enable
access-policy ftp
access-policy host
access-policy mode network precedence
access-policy name
access-policy snmp-group
action flushIp
action triggerRipUpdate
aggregate-address as-set
area import
area range
area virtual-link
area virtual-link message-digest-key
auto-negotiate enable
auto-negotiation-advertisements
auto-peer-restart enable
auto-recover-port port enable
auto-summary
auto-vlink
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
B
bandwidth-limit
banner
bgp
boot
boot config
boot config bootp
boot config bootp primary
boot config choice
boot config choice primary image-file
boot config cli
boot config delay
boot config flags
boot config flags 8616-reautoneg
boot config flags access-service
boot config flags block-snmp
boot config flags factorydefaults
boot config flags ftpd
boot config flags ha-cpu
boot config flags spanning-tree-mode
boot config flags sshd
boot config host
boot config master
boot config mezz-image
boot config mezz-image image-name
boot config net
boot config net mgmt ip
boot config net mgmt route
boot config sio modem
boot config tz
boot file config value
brouter port
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
C
cfm ethertype
cfm maintenance-association
cfm maintenance-domain
cfm maintenance-endpoint
clear filter
clear filter acl
clear ip arp interface
clear ip igmp igap-counters
clear ip ipfix
clear ip msdp peer
clear ip msdp sa-cache
clear ip msdp statistics
clear ip route interface
clear ip traffic-filter
clear ipv6 vrrp
clear isis lsdb
clear isis stats
clear khi all
clear khi chassis
clear khi forwarding
clear khi ip
clear khi log
clear khi performance
clear khi port
clear khi protocol
clear radius statistics
clear wireless-switch mac-address-entry
clear wireless-switch statistics
clilog
clilog enable
cli password
clock set
clock source
clock sync-time
comp-bestpath-med-confed
copy
copy srcfile destfile
cp-limit port multicast-limit
csnp-interval
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
D
debug ip pim
debug-screen
debug spbm isis recompute-fib
debug spbm isis recompute-fib-download
debug spbm l2vpn action-call
debug spbm l2vpn event-notify
debug spbm l2vpn fib-update
debug spbm l2vpn fib-update-cvlan
default-information
default ip
default ip igmp snoop-querier
default ip igmp snoop-querier-addr
default-metric (BGP)
default-metric (RIP)
dir
dos-format
dsapssap
dump ar
dump ercd record
dump rsp-trace egress-display-pkt
dump rsp-trace ingress-pkt-trace
duplex
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
E
eapol enable
eapol port
eapol sess-manage enable
eapol status
eapol status auto
eapol status unauthorized
enable
enable-diffserve
encapsulation dot1q
end
exit
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
F
filter acl
filter acl ace
filter acl ace action
filter acl ace advanced
filter acl ace arp
filter acl ace debug
filter acl ace ethernet
filter acl ace ip
filter acl ace ipv6
filter acl ace protocol
filter acl enable
filter acl port
filter acl set
filter acl set default-action
filter acl vlan
filter act
filter act name
filter act pattern
filter apply act
flap-dampening
flow-control
format-flash
fpga update
fpga update bmc
fpga update dpc
fpga update pim
fpga update rs-module-dpm
fpga update rs pim
framing sonet
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
G
global-debug
global-debug mask
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
H
high-secure enable
host-route
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
I
ibgp-report-import-rt
ignore-illegal-rtrid
install
interface-ip
ip access-list extended
ip address
ip alternative-route
ip apply redistribute isis
ip arp
ip arp inspection
ip arp inspection vlan
ip arp-proxy enable
ip arp-response
ip arp static-mcast
ip as-list
ip bfd brouter port
ip bfd vlan enable
ip bgp enable
ip bgp in-route-policy
ip bgp multiple-paths
ip bgp neighbor
ip bgp neighbor allow-as-in
ip bgp neighbor as-override
ip bgp neighbor remove-private-as
ip bgp neighbor site-of-origin
ip [bgp|ospf|rip] apply redistribute
ip bgp redistribute isis route-map
ip community-list
ip dhcp-relay
ip dhcp-relay broadcast
ip dhcp-relay fwd-path
ip dhcp-relay fwd-path enable
ip dhcp-relay fwd-path mode
ip dhcp snooping
ip dhcp snooping binding interface
ip dhcp snooping enable
ip dhcp snooping vlan enable
ip directed-broadcast enable
ip domain-name
ip dvmrp
ip dvmrp active
ip dvmrp advertise-self port
ip dvmrp advertise-self vlan
ip dvmrp default-listen ethernet port
ip dvmrp default-listen vlan
ip dvmrp enable ethernet port
ip dvmrp enable vlan
ip dvmrp in-policy ethernet port
ip dvmrp in-policy vlan
ip dvmrp interface-type active
ip dvmrp out-policy
ip dvmrp show-next-hop-table
ip ecmp
ip ecmp max-path
ip extcommunity-list
ip forward-protocol udp
ip forward-protocol udp broadcastmask
ip forward-protocol udp maxttl
ip forward-protocol udp portfwd
ip forward-protocol udp portfwdlist
ip icmp redirect
ip igmp access-list ethernet port
ip igmp access-list mode
ip igmp access-list mode vlan
ip igmp access-list vlan
ip igmp ethernet port
ip igmp generate-log
ip igmp igap
ip igmp immediate-leave
ip igmp immediate-leave-members
ip igmp immediate-leave-mode
ip igmp mrdisc
ip igmp snoop-querier
ip igmp snoop-querier-addr
ip igmp ssm group-range
ip igmp ssm-map
ip igmp static-group
ip igmp stream-limit
ip igmp stream-limit-group
ip igmp stream-limit-max-streams
ip igmp stream-limit vlan
ip igmp version
ip ipfix collector
ip ipfix enable
ip ipfix port
ip ipfix slot
ip irdp
ip irdp address
ip mroute interface
ip mroute resource-usage egress-threshold
ip mroute resource-usage log-msg trap-msg
ip mroute static-source-group
ip mroute stream-limit
ip mroute stream-limit interface
ip msdp connect-retry
ip msdp default-peer
ip msdp description
ip msdp enable
ip msdp implicit-default-peer
ip msdp keepalive
ip msdp md5-authentication
ip msdp mesh-group
ip msdp originator-id
ip msdp password peer
ip msdp peer
ip msdp redistribute
ip msdp sa-filter
ip msdp sa-limit
ip msdp ttl-threshold
ip name-server primary
ip ospf
ip ospf apply accept
ip ospf apply accept adv-rtr
ip ospf apply redistribute
ip ospf area
ip ospf bfd
ip ospf enable
ip ospf redistribute
ip ospf redistribute bgp
ip ospf redistribute bgp enable
ip ospf redistribute isis metric-type
ip ospf redistribute isis subnets
ip ospf spf-run
ip pgm enable
ip pgm enable vlan
ip pim bsr-candidate preference value ethernet port
ip pim bsr-candidate preference value vlan
ip pim enable
ip pim enable ethernet port
ip pim enable vlan
ip pim enable vrf
ip pim mbr
ip pim mode sparse
ip pim mode ssm
ip pim static-rp
ip pim virtual-neighbor
ip prefix-list
ip redistribute enable
ip redistribute isis
ip redistribute isis enable
ip redistribute isis metric
ip redistribute isis route-policy
ip rip
ip rip apply redistribute
ip rip out-policy
ip rip redistribute
ip rip redistribute bgp enable
ip route
ip route bfd
ip route default
ip route preference
ip route preference protocol spbm-level1
ip routing
ip rsmlt
ip rsmlt edge-support
ip rvs-path-chk mode port
ip rvs-path-chk mode vlan
ip-source-address
ip static-mroute
ip ttl
ipv6 area
ipv6 area range
ipv6 area virtual-link
ipv6 as-boundary-router enable
ipv6 dhcp-relay
ipv6 dhcp-relay fwd-path
ipv6 icmp error-interval
ipv6 interface address
ipv6 interface address vlan
ipv6 interface multicast-routing
ipv6 interface multicast-routing brouter
ipv6 mgmt-virtual
ipv6 mld
ipv6 mld brouter
ipv6 multicast-routing
ipv6 nd
ipv6 nd prefix
ipv6 nd prefix-interface
ipv6 neighbor
ipv6 ospf area
ipv6 ospf area vlan
ipv6 ospf enable
ipv6 ospf enable vlan
ipv6 ospf nbma-nbr
ipv6 ospf nbma-nbr vlan
ipv6 redistribute direct
ipv6 route
ipv6 tunnel
ipv6 tunnel vlan
ipv6 vrrp
ipv6 vrrp address
ip verify source interface
ipvpn
ipvpn enable
ipvpn service-label-allocation
ip vrf
ip vrf max-routes
ip vrrp
i-sid
isis
isis apply redistribute
isis apply redistribute vrf
isis enable
isis hello-auth type
isis l1-dr-priority
isis l1-hello-interval
isis l1-hello-multiplier
isis redistribute
isis redistribute enable
isis spbm
isis spbm interface-type
isis spbm l1-metric
ist enable
ist peer-ip
is-type
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
K
khi boot-delay
khi chassis
khi enable
khi performance
khi port
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
L
l2 ping
l2tracemroute source group cvlan
l2tracemroute source group vrf priority ttl
l2 traceroute
l2 tracetree
lacp
lacp enable
lacp enable key
lb-controller
link-flap-detect auto-port-down
link-flap-detect frequency
link-flap-detect interval
link-flap-detect send-trap
linktrace
load-encryption-module
load-license
lock port
logging
logging logToPCMCIA
logging transferfile
login-message
loopback
loop-detect action
loop-detect arp-detect
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
M
mac-security auto-learning
manual-area
match extended-prefix
max-logins
max-lsp-gen-interval
md5 filename
metric
mgmt-ip
min-lsp-gen-interval
mirror-by-port
mlt
mlt member
more boot.cfg
mpls ldp ethernet
mpls ldp globally
mpls ldp vlan
mpls router-id
mpls rsvp ethernet
mpls rsvp explicit-path
mpls rsvp globally
mpls rsvp lsp
mpls rsvp lsp primary
mpls rsvp resource
mpls rsvp static-ip
mpls rsvp vlan
mpls statistics receive
mpls statistics receive start-label
mpls statistics transmit
mpls statistics transmit start-label
multicast enable
multicast fwd-cache-timeout
multicast mlt-distribution enable
multicast mlt-distribution globally
multicast mlt-distribution multilink trunk
multicast smlt-square
multicast software-forwarding
mvpn enable
mvpn fwd-cache-timeout
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
N
name port
neighbor
neighbor a.b.c.d fall-over bfd
neighbor address-family vpnv4
neighbor-debug-all
neighbor-debug-all mask
neighbor ipaddress
neighbor ipvpn-lite-capability
net6-mgmt ipv6
net6-mgmt ipv6 route
network
nlb-mode unicast
no access-diffserve enable
no access-policy
no boot config flags autoboot
no cfm maintenance-association
no cfm maintenance-domain
no cfm maintenance-endpoint
no cfm maintenance-endpoint enable
no ip igmp snoop-querier
no ip igmp snoop-querier-addr
no ip msdp peer
no ip msdp redistribute route-policy
no ip route
no ipvpn
no ist enable
no ist peer-ip
no-med-path-is-worst
no mlt member
no pcap enable
no pcap enable globally
no qos 802.1p-override
no tacacs enable
no tacacs server
nsna enable
nsna nsnas
nsna phone-signature
nsna port
nsna uplink vlans
nsna vlan
ntp authentication-key
ntp interval
ntp server
ntp server auth-enable
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
O
overload
overload-on-startup
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
P
password access-level
password aging-time
password aging-time
password default-lockout-time
password lockout
password min-passwd-len
password password-history
passwordprompt
pcap 1-1000
pcap capture-filter
pcap enable
pcap enable mode
pcap enable mode
pcap reset-stat
peer telnet
ping
ping hostname
ping-mpls ipv4
ping-mpls rsvp
ping-snoop
pluggable-optical-module
portlock enable
port-phy portlist
psnp-interval
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
Q
qos 802.1p-override
qos apply egress-queue-set
qos egressmap exp
qos egress-queue-set
qos egress-queue-set qmax
qos egress-queue-set queue
qos if-policer
qos if-shaper
qos ingressmap exp
qos level port
qos level vlan
qos policy
quick-start
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
R
radius
radius accounting
radius cli-cmd-count
radius cli-profile
radius command-access-attribute
radius enable
radius enable eapol
radius igap-timeout-log-fsize
radius mcast-addr-attr-value
radius server host
radius server host used-by igap
radius-snmp acct-enable
radius sourceip-flag
rd
redistribute
redistribute enable
redistribute isis
redistribute isis enable
redistribute isis metric
redistribute isis metric-type
redistribute isis route-map
redistribute isis route-policy
redistribute isis subnets
redistribute ospf
remote-mirroring
remote-vlan-stg
remove word
reset
retransmit-lsp-interval
rip enable
rmon
route-map
route-map enable
route-map match
route-map match condition
route-map match extcommunity
route-map permit
route-map policy name seq number
route-map policyname seqnumber
route-map policy name seq number permit
router bfd enable
router bgp
router bgp enable
route-reflector enable
route-refresh
router-id
router isis
router isis enable
router ospf enable
router ospf ipv6-enable
router vrf
route-target both
route-target import
routing
rsp-trace ingress-pkt-trace enable
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
S
save bootconfig
save config
save config file
save config file mode acli
save config file mode cli
save config mode
save config standby
save trace
sffd enable
show access-policy
show autotopology nnm-table
show banner
show basic config
show bgp ipv6 aggregates
show bgp ipv6 imported-routes
show bgp ipv6 neighbors
show bgp ipv6 networks
show bgp ipv6 redistributed-routes
show bgp ipv6 route
show boot config
show boot config choice
show boot config flags
show boot config master
show brouter
show cfm ethertype
show cfm maintenance-association
show cfm maintenance-domain
show cfm maintenance-endpoint
show cli info
show clilog
show clilog file
show cli password
show clock
show eapol
show fdb-filter
show filter acl
show filter acl ace
show filter acl action
show filter acl advanced
show filter acl arp
show filter acl config
show filter acl debug
show filter acl ethernet
show filter acl ip
show filter acl ipv6
show filter acl protocol
show filter acl statistics port
show filter act
show filter act-pattern
show fulltech
show ha-state
show history
show hosts
show interfaces atm statistics
show interfaces atm statistics ds3fecurrent
show interfaces atm statistics ds3feinterval
show interfaces atm statistics ds3fetotal
show interfaces atm statistics ds3necurrent
show interfaces atm statistics ds3neinterval
show interfaces atm statistics ds3netotal
show interfaces atm statistics felinecurrent
show interfaces atm statistics felineinterval
show interfaces atm statistics fepathcurrent
show interfaces atm statistics fepathinterval
show interfaces atm statistics linecurrent
show interfaces atm statistics lineinterval
show interfaces atm statistics pathcurrent
show interfaces atm statistics pathinterval
show interfaces atm statistics sectioncurrent
show interfaces atm statistics sectioninterval
show interfaces atm statistics sonetmediumtbl
show interfaces dhcp-relay
show interfaces error ospf
show interfaces FastEthernet error
show interfaces FastEthernet statistics
show interfaces gigabitEthernet
show interfaces loopback
show interfaces statistics
show interfaces statistics dhcp-relay
show interfaces statistics egress-queues
show interfaces statistics ipvpn
show interfaces statistics lacp
show interfaces statistics rmon
show interfaces statistics stg
show interfaces statistics verbose
show interfaces vlan
show ip
show ip access-list extended
show ip arp
show ip arp inspection interface
show ip arp inspection vlan
show ip arp interface
show ip arp -s
show ip arp static-mcastmac
show ip as-list
show ip bfd
show ip bfd interfaces
show ip bfd neighbors
show ip bfd neighbors next-hop
show ip bfd stats
show ip bgp aggregates
show ip bgp cidr-only
show ip bgp conf
show ip bgp confederation
show ip bgp dampened-paths
show ip bgp flap-damp-config
show ip bgp imported-routes
show ip bgp neighbors
show ip bgp neighbors A.B.C.D
show ip bgp networks
show ip bgp peer-group
show ip bgp redistributed-routes
show ip bgp route
show ip bgp stats
show ip bgp summary
show ip bgp vpnv4
show ip community-list
show ip dhcp-relay
show ip dhcp snooping
show ip dhcp snooping binding
show ip dhcp snooping interface
show ip dhcp snooping vlan
show ip directed-broadcast interface
show ip dns
show ip dvmrp
show ip dvmrp interface
show ip dvmrp neighbor
show ip dvmrp next-hop
show ip dvmrp route
show ip ecmp
show ip extcommunity-list
show ip forward-protocol udp
show ip forward-protocol udp portfwd
show ip forward-protocol udp portfwdlist
show ip igmp access
show ip igmp cache
show ip igmp group
show ip igmp igap
show ip igmp igap counters
show ip igmp igap group
show ip igmp interface
show ip igmp mrdisc
show ip igmp mrdisc neighbors
show ip igmp router-alert
show ip igmp sender
show ip igmp snooping
show ip igmp snoop-trace
show ip igmp ssm
show ip igmp ssm-map
show ip igmp static
show ip igmp stream-limit interface
show ip igmp sys
show ip interface
show ip ipfix
show ip ipfix export
show ip ipfix hash-statistics
show ip ipvpn
show ip ipvpn rd
show ip ipvpn route-target
show ip irdp
show ip irdp interface
show ip isis redistribute
show ip mroute hw-group-prune-state
show ip mroute hw-group-trace
show ip mroute hw-resource-usage
show ip mroute interface
show ip mroute next-hop
show ip mroute route
show ip mroute static-source-group
show ip msdp count
show ip msdp mesh-group
show ip msdp peer
show ip msdp rpf
show ip msdp sa-cache
show ip msdp sa-check source
show ip msdp show-all
show ip msdp summary
show ip ospf
show ip ospf accept
show ip ospf area
show ip ospf area-range
show ip ospf ase
show ip ospf authentication interface
show ip ospf default-cost
show ip ospf host-route
show ip ospf ifstats
show ip ospf int-auth
show ip ospf interface
show ip ospf int-timers
show ip ospf lsdb
show ip ospf neighbor
show ip ospf neighbors interface
show ip ospf port-error
show ip ospf redistribute
show ip ospf stats
show ip ospf virtual-link
show ip pgm
show ip pgm interface
show ip pgm interface statistics nak
show ip pgm interface statistics parity
show ip pgm retransmit
show ip pgm session
show ip pim
show ip pim active-rp
show ip pim bsr
show ip pim interface
show ip pim mode
show ip pim mroute
show ip pim neighbor
show ip pim rp-candidate
show ip pim rp-hash
show ip pim static-rp
show ip pim virtual-neighbor
show ip prefix-list
show ip redistribute
show ip rip
show ip rip interface
show ip rip redistribute
show ip route
show ip route a.b.c.d
show ip route count-summary
show ip route preference
show ip routing
show ip rsmlt
show ip rsmlt edge-support
show ip source binding
show ip static-mroute
show ip tcp statistics
show ip traffic-filter
show ipv6 address interface
show ipv6 dhcp-relay counters
show ipv6 dhcp-relay fwd-path
show ipv6 dhcp-relay interface
show ipv6 forwarding
show ipv6 global
show ipv6 interface
show ipv6 mld-cache interface
show ipv6 mld interface
show ipv6 nd-prefix interface
show ipv6 neighbor
show ipv6 ospf
show ipv6 ospf area
show ipv6 ospf int-timers
show ipv6 ospf lsdb
show ipv6 ospf neighbor
show ipv6 ospf vlan interface
show ipv6 prefix-list
show ipv6 route static
show ipv6 TCP
show ipv6 trace
show ipv6 tunnel
show ipv6 UDP
show ipv6 vrrp
show ipv6 vrrp address
show ipv6 vrrp interface
show ipv6 vrrp statistics
show ip verify source
show ip vrf
show ip vrf max-routes
show ip vrrp address
show ip vrrp interface vlan
show ip vrrp statistics
show isis
show isis adjacencies
show isis area
show isis int-auth
show isis int-ckt-level
show isis int-counters
show isis interface
show isis int-l1-cntl-pkts
show isis int-l2-cntl-pkts
show isis int-timers
show isis lsdb
show isis manual-area
show isis net
show isis spbm
show isis spbm drop-stats port last drop
show isis spbm drop-stats port rpfc-multicast-sa
show isis spbm drop-stats port rpft-unicast-sa
show isis spbm drop-stats port unknown-multicast-da
show isis spbm drop-stats port unknown-unicast-da
show isis spbm ip-multicast route
show isis spbm ip-unicast-fib
show isis spbm i-sid
show isis spbm multicast-fib
show isis spbm nick-name
show isis spbm show-all
show isis spbm unicast-fib
show isis spbm unicast-tree
show isis statistics
show isis system-id
show ist
show khi chassis
show khi forwarding
show khi info
show khi ip-interface
show khi mgmt
show khi performance
show khi port
show khi protocol-stats
show lacp
show lacp interface
show license
show link-flap-detect
show log file
show logging config
show logging file
show logging level
show logging transferfile
show mirror-by-port
show mlt error collision
show mlt error main
show mlt stats
show monitor-statistics
show mpls basic
show mpls ftn
show mpls ilm
show mpls ldp
show mpls ldp bindings
show mpls ldp discovery
show mpls ldp interface
show mpls ldp neighbor
show mpls ldp route
show mpls ldp session
show mpls ldp summary
show mpls mtu
show mpls rsvp
show mpls rsvp explicit-path
show mpls rsvp interface
show mpls rsvp neighbor
show mpls rsvp paths
show mpls rsvp resource
show mpls rsvp static-ip lsp
show mpls statistics ldp
show mpls statistics receive
show mpls statistics rsvp
show mpls statistics transmit
show multicast mlt-distribution
show multicast software-forwarding
show multicast square-smlt
show nsna client
show nsna interface
show nsna nsnas
show nsna phone-signature
show nsna vlan
show ntp server
show pcap
show pcap capture-filter
show pcap dump
show pcap port
show pcap stats
show ping-snoop
show pluggable-optical-module
show ports statistics ospf extended
show ports statistics ospf main
show ports statistics ospf main
show port statistics wis felinecurrent
show port statistics wis felineinterval
show port statistics wis fepathcurrent
show port statistics wis fepathinterval
show port statistics wis linecurrent
show port statistics wis lineinterval
show port statistics wis pathcurrent
show port statistics wis pathinterval
show port statistics wis sectioncurrent
show port statistics wis sectioninterval
show port statistics wis sonetmedium
show qos 802.1p-override
show qos egressmap
show qos egress-queue-set
show qos eqmap
show qos ingressmap
show qos policer
show qos policy-config
show qos shaper
show qos statistics
show qos statistics egress-queue-set
show qos statistics policy
show radius
show radius-server
show radius-server statistics
show radius snmp
show remote-mirroring
show rmon
show rmon alarm
show rmon event
show rmon history
show rmon log
show rmon stats
show route-map
show routing statistics
show routing statistics interface
show rsp-trace
show running-config
show running-config mode acli
show slot
show slpp
show slpp interface
show smlt
show snmplog
show snmp-serve host
show snmp-server
show snmp-server notify-filter
show sonet statistic interfaces pos activealarms
show sonet statistic interfaces pos felinecurrent
show sonet statistic interfaces pos felineinterval
show sonet statistic interfaces pos fepathcurrent
show sonet statistic interfaces pos fepathinterval
show sonet statistic interfaces pos linecurrent
show sonet statistic interfaces pos lineinterval
show sonet statistic interfaces pos linkstatus
show sonet statistic interfaces pos lqrstatus
show sonet statistic interfaces pos pathcurrent
show sonet statistic interfaces pos pathinterval
show sonet statistic interfaces pos pppiftbl
show sonet statistic interfaces pos sectioncurrent
show sonet statistic interfaces pos sectioninterval
show sonet statistic interfaces pos sonetmediumtbl
show spanning-tree bpdu-filtering
show spanning-tree config
show spanning-tree mstp config
show spanning-tree mstp port role
show spanning-tree mstp statistics
show spanning-tree mstp status
show spanning-tree port detail
show spanning-tree rstp config
show spanning-tree rstp port config
show spanning-tree rstp port role
show spanning-tree rstp port statistics
show spanning-tree rstp port status
show spanning-tree rstp statistics
show spanning-tree rstp status
show spanning-tree status
show spanning-tree stp config
show spanning-tree stp status
show spanning-tree vlans
show spbm
show ssh
show sys
show sys 8648gtr
show sys flags
show sys-info
show syslog
show syslog host
show sys perf
show sys performance
show sys power
show sys power global
show sys power power-supply
show sys power slot
show sys software
show tacacs
show tech
show telnet-access
show test all
show test artable
show test fabric
show trace
show users
show vlacp interface
show vlan advance
show vlan autolearn-mac
show vlan basic
show vlan brouter-port
show vlan dvmrp
show vlan idsvlan
show vlan i-sid
show vlan mac-address-entry
show vlan mac-address-filter
show vlan mac-address-static
show vlan manual-edit-mac
show vlan members
show vlan nodal-mep
show vlan nodal-mip-level
show vlan remote-mac-table
show vlan srcmac
show vlan static-mcastmac
show web-server
show wireless switch
show wireless-switch lb-controller
show wireless-switch mac-address-entry
show wireless switch peer-advertized-vlans
show wireless-switch peer-devices
show wireless-switch tunnel
show wireless-switch tunnel-statistics
show wireless-switch tunnel-statistics bridging
show wireless-switch tunnel-statistics keepalive
show wireless-switch tunnel-statistics routing
show wireless-switch vlan-map
show wireless-switch vlan-reservation
show wireless-switch vlan-servers
shutdown
slot reset
slpp enable
slpp ethertype
slpp port
slpp tx-interval
slpp vid
smlt
smlt port
snmplog
snmp-server
snmp-server
snmp-server community
snmp-server group
snmp-server host v1
snmp-server host v2
snmp-server host v3
snmp-server notify-filter
snmp-server sender-ip
snmp-server user
snmp-server user engine-id
snmp-server user group
snmp-server view
source file
spanning-tree mstp msti
spanning-tree rstp version
spanning-tree stp
spanning-tree stp change-detection
spanning-tree stp create
spanning-tree stp trap-stp
spbm
spbm b-vid
spbm ethertype
spbm ip enable
spbm lsdb-trap enable
spbm nick-name
spbm smlt-peer-system-id
spbm smlt-virtual-bmac
spb-multicast enable
speed
spf-delay
spoof-detect portlist enable
ssh
svlan
svlan-porttype
synchronization
sys 8648gtr high-priority-control-mac
sys action
sys action cpu-switch-over
sys ecn-compatibility
sys ext-cp-limit max-ports-to-check
sys ext-cp-limit min-congestion-time
sys ext-cp-limit port
sys ext-cp-limit port-congestion-time
sys ext-cp-limit trap-level
sys flags enhanced-operational-mode
sys flags global-filter-ordering
sys force-msg
sys global-filter
sys hash-calc getmltindex traffic-type
syslog enable
syslog host
sys max-vlan-resource-reservation
sys mgmt-virtual-ip
sys msg-control
sys msg-control action
sys msg-control control-interval
sys msg-control max-msg-num
sys mtu
sys multicast-resource-reservation
sys name
sys-name
sys power
sys record-reservation
system-id
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
T
tacacs enable
tacacs server
tcp-udp-base-port
telnet-access login-timeout
telnet-access sessions
terminal more disable
test artable
test fabric
test hardware
test led
test portList
trace auto enable
trace auto module
trace ethernet destination-mac
trace ethernet disable
trace ethernet enable
trace ethernet port
trace flags isis
trace ipv6
trace level
traceroute
trace screen
trace syslog destination
trace syslog disable
trace syslog enable
traps
tx-flow-control enable
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
U
udp checksum
udpsrc-by-vip
untagged-frames-discard enable
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
V
vendorname nasIPaddress type version.log
vlacp
vlacp enable
vlan action
vlan create
vlan create type spbm-bvlan
vlan create type svlan
vlan create type svlan-mstprstp
vlan i-sid
vlan mac-address-entry
vlan mac-address-entry status
vlan mac-address-filter
vlan mac-address-filter notallowfrom
vlan mac-address-static
vlan-map
vlan-map lvid
vlan-map name
vlan-map weight
vlan members
vlan nodal-mep
vlan nodal-mip-level
vlan-reservation
vlan srcmac
vrf
vrf word 0-16
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
W
wan-mode
web-server enable
A | B | C | D | E | F | G | H | I | K | L | M | N | O | P | Q | R | S | T | U | V | W | Back to top
All modes
BGP Router configuration mode
Configuration Mode
FastEthernet or GigabitEthernet Interface configuration mode
Gigabitethernet Interface configuration mode
Global configuration mode
Interface configuration mode
IS-IS configuration mode
IS-IS configuration mode or Global configuration mode
OSPF Router Configuration mode
Privileged EXEC mode
Privileged EXEC mode/Global configuration mode
Router IS-IS configuration mode
User EXEC mode
VLAN Interface configuration code
VRF configuration mode
VRF router configuration mode
WLAN Switch Configuration
Back to top
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:accept adv-rtr
accept adv-rtr
Use a route policy to define how the switch redistributes external routes from a specified source into an OSPF domain. The policy
defines which route types the switch accepts and redistributes.
Syntax
accept adv-rtr <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<A.B.C.D> Specifies the IP address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:accept adv-rtr enable
Syntax
accept adv-rtr <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables an OSPF accept entry for a specified advertising router.
Indicates the OSPF external type. This parameter describes which types of
metric-type OSPF external routes match this entry. any means match all external routes.
{type1|type2|any} type1 means match external type 1 only. type2 means match external type 2
only.
Specifies the name of the route policy to use for filtering external routes
route-policy
<WORD> advertised by the specified advertising router before accepting into the routing
table.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:access-diffserve
access-diffserve
Configure a port as untrusted to determine the Layer 3 QoS actions the switch performs. An untrusted port overrides DSCP
markings.
Syntax
access-diffserv [port <portList>] [enable]
Default
The default is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
If enabled, specifies an access port and overrides incoming DSCP bits. If disabled,
specifies a core port and honors and handles incoming DSCP bits. The default is
enable disabled. To use the default configuration, use the default option in the command
default access-diffserv [enable] To delete the current configuration, use the no option
in the command no access-diffserv [enable]
port Specifies the slot and port, or slot and port list. To delete the current configuration, use
<portList> the no option in the command no access-diffserv [port <portList>]
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:access-policy
access-policy
Configure the SNMP service in SNMP group access policies if you are upgrading from Release 3.7 or earlier to Release 4.1.x or
later to access the Avaya Ethernet Routing Switch 8800/8600 using Device Manager.
Syntax
access-policy <1-65535>
Default
Command mode
Global configuration mode
Command parameters
Parameter Description
The access-strict mode determines whether or not users with access
levels greater than the one configured for the policy are allowed access.
access-strict For example, if the access-level is set to rw, and access-strict is set, only
users with rw access are given access. If access-strict is not set, both rw
and rwa users are given access.
<ro|rw|rwa> specifies read-only, read-write, and read-write-access
access levels. The access level is the level that a user needs to be
accesslevel
<ro|rw|rwa> granted access. If the user access-level is greater than that configured for
the policy, access is granted, depending on the access-strict parameter
value.
enable Enable the access policy. To disable the access policy, use the no access-
policy <1-65535> enable command.
ftp Enables File Transfer Protocol.
<WORD 0-46> specifies the host IPv4 or IPv6 address. If you configure
host <WORD 0-46> the host address, the policy is only applied if the source IP address
matches the host address.
http Enables Hypertext Transfer Protocol.
mode <allow|deny> The mode determines whether access is allowed or denied.
name <WORD 0-15> <WORD 0-15> specifies a name, which can be a maximum of 15
characters long.
<A.B.C.D> specifies the network IP address, and <X.X.X.X> specifies the
network <A.B.C.D>
<X.X.X.X> subnetwork mask. If you configure the network address, the policy is only
applied if the source IP address matches the network address.
<1-128> specifies the precedence given to this access policy. If more
precedence <1-128> than one policy is matched for an incoming request, the precedence
determines which policy is applied. The lower the precedence, the higher
the priority.
rlogin Enables rlogin access.
<WORD 1-32> adds an SNMP group to the policy. The group name can
be a maximum of 32 characters long. <snmpv1|snmpv2c|usm> specifies
snmp-group <WORD 1-
32> whether to use the SNMPv1 security model, the SNMPv2 security model,
<snmpv1|snmpv2c|usm> or the user-based security model (usm). To delete a group from the
policy, use the no snmp-group <WORD 1-32> <snmpv1|snmpv2c|usm>
command.
snmpv3 Enables SNMPv3 access.
ssh Enables Secure Shell access.
telnet Enables Telnet access.
tftp Enables Trivial File Transfer Protocol access.
username <WORD 0- <WORD 0-30> specifies the trusted host user name, which can be a
30> maximum of 30 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:access-policy access-restrict
access-policy access-restrict
Configure an access policy to control access to the switch.
Syntax
access-policy <1-65535> [access-strict] [accesslevel <ro|rwa|rw>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
If this parameter is activated, only the current configuration for access level is accepted.
access- If this parameter is disabled, access is limited up to the level configured. Use the no
strict operator to remove this configuration. To set this option to the default value, use the
default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:access-policy by-mac
access-policy by-mac
Configure access-policies by MAC address to allow or deny local MAC addresses on the network management port after an access
policy is activated.
Syntax
access-policy by-mac <0x00:0x00:0x00:0x00:0x00:0x00> action <allow|deny>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<0x00:0x00:0x00:0x00: Adds a MAC address to the policy. Specify the MAC address in
0x00:0x00> hexadecimal format.
<allow|deny> Specifies the action to take for the MAC address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:access-policy enable
access-policy enable
Enable the access policy globally to control access across the switch.
Syntax
access-policy <1-65535> enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the access policy globally on the switch.
<1-65535> Specifies the policy ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:access-policy ftp
access-policy ftp
Configure optional access protocols for an access policy on the switch.
Syntax
access-policy <1-65535> [ftp] [http] [ssh] [telnet] [tftp]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Activates or disables FTP for the specified policy. Because FTP derives its logon or
password from the CLI management filters, FTP works for the logins read-write-only
ftp (rwo) and read-write (rw); however, it does not work for the login read-only (ro). Use
the no operator to remove this configuration. To set this option to the default value, use
the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:access-policy host
access-policy host
Configure optional rlogin access for an access policy on the switch.
Syntax
access-policy <1-65535> host <word> rlogin username <word>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
host <word> For rlogin access, specifies the trusted host address as an IP address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:access-policy mode network
precedence
Syntax
access-policy <1-65535> [mode <allow|deny>] [network <A.B.C.D>] [precedence <1-128>]
Default
The default is allow.
Command mode
Global configuration mode
Command parameters
Parameter Description
mode Specifies whether this network address is allowed or denied access through the
<allow|deny> specified access service. The default is allow.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:access-policy name
access-policy name
Assign a name to the access policy to uniquely identify the policy.
Syntax
access-policy <1-65535> name <word>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
name <word> Specifies a name using a string from 015 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:access-policy snmp-group
access-policy snmp-group
Configure optional SNMP parameters for an access policy on the switch.
Syntax
access-policy <1-65535> [snmp-group <word> <snmpv1|snmpv2c|usm>] [snmpv3]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Adds snmp-v3 group under this access policy. word is the snmp-v3 group
snmp-group <word> name of 132 characters. <snmpv1|snmpv2c|usm> is the security model
<snmpv1|snmpv2c|usm> {snmpv1|snmpv2c|usm}. Use the no operator to remove this
configuration.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:action flushIp
action flushIp
Use this command to flush the routing tables for administrative and troubleshooting purposes.To flush tables on a VRF instance for
a port or VLAN, ensure that the VRF is associated with the port or VLAN.
Syntax
action flushIp
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
flushIp Flushes the IP routing tables by port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:action triggerRipUpdate
action triggerRipUpdate
Force RIP to update the routing table so that the port or VLAN uses the latest routing information.
Syntax
action triggerRipUpdate
Default
None
Command mode
Global configuration mode
aggregate-address as-set
Adds or deletes an aggregate address in a BGP routing table.
Syntax
aggregate-address <prefix/len> [as-set] [summary-only] [suppress-map <WORD 0-1536>]
[advertise-map <WORD 0-1536>] [attribute-map <WORD 0-1536>]
Default
The default value is disable.
Command mode
Global configuration mode
Command parameters
Parameter Description
<prefix/len> Specifies the IP address and an integer value (between 0 and 32).
as-set Enables autonomous system information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:area import
area import
Import information from other areas to learn their OSPF relationships and create normal, stubby, or not-so-stubby areas (NSSA).
Place stubby or NSSAs at the edge of an OSPF routing domain.
Syntax
area <A.B.C.D> import <external|noexternal|nssa>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the type of area:external-Stub and NSSA (not so stubby
import
<external|noexternal|nssa> area). are both false noexternal-Configures the area as stub area.
nssa-Configures the area as NSSA.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:area range
area range
Use aggregate area ranges to reduce the number of link-state advertisements that are required within the area. You can also
control advertisements.
Syntax
area range <A.B.C.D> <A.B.C.D/0-32> <summary-link|nssa-extlink>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<A.B.C.D> <A.B.C.D> identifies an OSPF area and <A.B.C.D/0-32> is the IP address
<A.B.C.D/0-32> and subnet mask of the range, respectively.
<summary- Specifies the LSA type. If you configure the range as type nssa-extlink then
link|nssa-
extlink> you cannot configure the advertise-metric.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:area virtual-link
area virtual-link
Use manual virtual interfaces to provide a backup link for vital OSPF traffic with a minimum of resource use.
Syntax
area virtual-link <A.B.C.D> <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<cr> Creates a virtual interface area identifier. <A.B.C.D> <A.B.C.D> specify the area ID and
the virtual interface ID, respectively.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:area virtual-link message-
digest-key
Syntax
area virtual-link message-digest-key <A.B.C.D> <A.B.C.D/0-32> <1-255> md5-key <WORD>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<A.B.C.D> Adds an MD5 key to the interface. At most, you can configure two MD5 keys to an
<A.B.C.D/0- interface. <A.B.C.D> identifies an OSPF area. <A.B.C.D/0-32> is the IP address
32> <1-255>
md5-key <WORD and subnet mask of the range. <1-255> is the ID for the message digest key
0-16> <WORD 0-16> is an alphanumeric password of up to 16 characters
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:auto-negotiate enable
auto-negotiate enable
Enable AutoNegotiation on the Ethernet port to optimally operate on the network.
Syntax
auto-negotiate enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables or disables AutoNegotiation for the port or other ports of
the module or both.
port {slot/port[-
slot/port][,...]} Specifies the slot and the port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:auto-negotiation-
advertisements
auto-negotiation-advertisements
Configure autonegotiation advertisements after enabling autonegotiation.
Syntax
auto-negotiation-advertisements <10-full|10-half|100-full|100-half|1000-full|1000-
half|none>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
10-full Advertises 10mbps full duplex.
10-half Advertises 10mbps half duplex.
100-full Advertises 100mbps full duplex.
100-half Advertises 100mbps half duplex.
1000-full Advertises 1000mbps full duplex.
1000-half Advertises 1000mbps half duplex.
none Sets the value to none.
port {slot/port[-slot/port][,...]} Specifies the slot and the port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:auto-peer-restart enable
auto-peer-restart enable
Enables the process that automatically restarts a connection to a BGP neighbor.
Syntax
auto-peer-restart enable
Default
The default value is enable.
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the process that automatically restarts a connection to a BGP neighbor.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:auto-recover-port port
enable
Syntax
auto-recover-port [port <portList>] [enable]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables spoof detection on the port.
<portList> Specifies the port list.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:auto-summary
auto-summary
Summarize networks based on class limits after BGP is enabled. (For example, Class A, B, C networks).
Syntax
auto-summary
Default
The default value is enable.
Command mode
Global configuration mode
auto-vlink
Use automatic virtual links to provide an automatic, dynamic backup link for vital OSPF traffic. Automatic virtual links require more
system resources than manually configured virtual links.
Syntax
auto-vlink
Default
None
Command mode
Global configuration mode
bandwidth-limit
Configure broadcast and multicast bandwidth limiting to restrict the amount of ingress broadcast and multicast traffic on a port.
The switch drops traffic that violates the bandwidth limit.
Syntax
bandwidth-limit [port <portList>] broadcast <250-2147483647>
Default
The default is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the bandwidth limit for broadcast traffic from 2502147483647 Kb/s. To
broadcast delete the current configuration, use the no option in the command: no bandwidth-
<250-
2147483647> limit [port <portList>] broadcast To use the default configuration, use the default
option in the command: default bandwidth-limit broadcast.
Specifies the slot and port, or a list of slots and ports. To delete the current
port configuration, use the no option in the command: no bandwidth-limit port <portList>
<portList> To use the default configuration, use the default option in the command: default
bandwidth-limit port <portList>
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:banner
banner
Configure the ACLI logon banner to display a warning message to users before authentication.
Syntax
banner <custom|static>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
custom|static Activates or disables using the default banner.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:bgp
bgp
Configure the IP BGP configuration commands.
Syntax
bgp aggregation enable
Default
The default value is enable.
Command mode
Global configuration mode
Command parameters
Parameter Description
aggregation enable Enables or disables the aggregation feature on this interface.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot
boot
Boot the Avaya Ethernet Routing Switch 8800/8600 with the new boot-monitor image.
Syntax
boot /flash/p80b5000.img
Default
None
Command mode
Global configuration mode
boot config
System logs are a valuable diagnostic tool. You can send log messages to a PCMCIA card for later retrieval.
Syntax
boot config flags logging
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Enables or disables logging to a PCMCIA card. The log file is named using an 8.3
(xxxxxxxx.sss) format. The first six characters of the file name contain the last three
bytes of the chassis base MAC address. The next two characters specify the slot number
flags
logging of the SF/CPU that generated the logs. The last three characters denote the sequence
number of the log file. Multiple sequence numbers are generated for the same chassis
and same slot, if the SF/CPU is replaced, reinserted, or if the maximum log file size is
reached.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config bootp
Syntax
boot config bootp <Primary|Secondary> <WORD 0-127> <1-10>
Default
Command mode
Global configuration mode
Command parameters
Parameter Description
<primary|secondary> WORD Sets the primary or the secondary image name with a string length
0-127 of 0 to 127.
<1-10> Specifies the slot number in the range of 1 to 10.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config bootp primary
Syntax
boot config bootp Primary default <1-4,7-10>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-4,7-10> Specifies the slots that have installed R or RS modules.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config choice
Syntax
boot config choice <primary|secondary|tertiary> [config-file <WORD 0-255>|backup-config-
file <WORD 0-255>|image-file <WORD 0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Identifies the backup boot configuration file. file is the device
backup-config-file <file> and file name, up to 255 characters including the path. To set
this option to the default value, use the default operator with
the command.
Lists the order in which the specified boot devices are accessed
<primary|secondary|tertiary> after you reboot the switch. The default order is to access the
PCMCIA card first, and then the onboard flash.
<primary|secondary|tertiary> Specifies the boot choice as one of the following:primary
secondary tertiary
config file <Word 0-255> Sets run-time configuration file to load.
backup-config-file <Word 0-
255> Sets run-time backup configuration file to load.
image-file <Word 0-255> Sets run-time image to load.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config choice primary
image-file
Syntax
boot config choice primary image-file /flash/p80a5000.img
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
image-file Sets run-time image to load.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config cli
Syntax
boot config cli [more]
Default
The default value is true.
Command mode
Global configuration mode
Command parameters
Parameter Description
Configures scrolling for the output display. The default is true. Use the no operator to
more remove this configuration. To set this option to the default value, use the default
operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config delay
Syntax
boot config delay <seconds>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
delay <seconds> Sets the slave delay time in seconds. The value ranges from 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config flags
Syntax
boot config flags
Default
Default values updated along with the variables in the parameters table.
Command mode
Global configuration mode
Command parameters
Parameter Description
8100-mode Turns the flag ON or OFF. The default value is false.
8616-reautoneg Permits 8616 modules to reautonegotiate when connected to a Multiservice
Switch 15000. The default value is false.
Activates the alternate LED behavior. The default is disabled. If you change
alt-led this parameter, you must reset the switch. The default is false.Important
For internal Avaya use only. Do not change this parameter unless directed
by Avaya.
Enables the switch automatically runs the run-time image after reset. When
autoboot disabled, the boot process stops at the boot monitor prompt. Configuring
autoboot to false is useful for some debugging tasks. The default is
enabled. If you change this parameter, you must reset the switch.
block-snmp When enabled, blocks Simple Network Management Protocol (SNMP)
management. The default is disabled.
When enabled, prevents the secondary SF/CPU in warm standby mode
block-warmstandby- from becoming the primary SF/CPU when the primary SF/CPU is reset. The
switchover default is disabled. If you change this parameter, you must reset the
switch.
Activates or disables Daylight Saving Time (DST) for the switch. After
daylight-saving-
time enabling, set the DST settings with the config bootconfig tz command. The
default is disabled.
Activates or disables run-time debugging of the configuration file. When
debug-config enabled, the line by line processing of the configuration file is displayed on
the console when the SF/CPU is initializing. The default is disabled. If you
change this parameter, you must reset the switch.
Controls whether the switch stops in debug mode following a fatal error.
Debug mode provides information equivalent to the trace commands. After
the flag is activated, the switch does not reboot following a fatal error.
debugmode After the flag is disabled, the switch automatically reboots following a fatal
error. The default is disabled. If you change this parameter, you must reset
the switch. Important For internal Avaya use only. Do not change this
parameter unless directed by Avaya.
Activates the ability to mirror egress traffic for E and M modules. The
egress-mirror default is activated. If you change this parameter, you must reset the
switch.
Specifies whether the switch boots with the factory defaults. The default is
factorydefaults disabled. This flag is automatically set back to the default setting after the
CPU turn on. If you change this parameter, you must reset the switch.
ftpd Enables FTP server.
ha-cpu Enables high availability of the CPU.
Activates or disables High Secure mode in the switch. This flag introduces
the following behaviors for the password: 10 characters enforcement, aging
time, limitation of failed logon attempts, and a protection mechanism to
hsecure filter certain IP addresses. The default is false. After you enable High
Secure mode, you must reset the switch to enforce secure passwords. In
High Secure mode, a user with an invalid-length password is prompted to
change their password.
Activates or disables system logging to a file on the PCMCIA, if present.
The default is true. The log file is named using an 8.3 (xxxxxxxx.sss)
format. The first 6 characters of the file name contain the last three bytes
logging of the chassis base MAC address. The next two characters specify the slot
number of the CPU that generated the logs. The last three characters
denote the sequence number of the log file. Multiple sequence numbers are
generated for the same chassis and same slot, if the CPU is replaced,
reinserted, or if the maximum log file size is reached.
Permits or prevents the mezzanine card from booting when it is present on
a SF/CPU card. The SuperMezz configuration must be identical on a dual
mezz CPU chassis: both CPUs have a SuperMezz or both CPUs are without a
SuperMezz. The default is enabled. If you change this parameter, you must
reset the switch. Before you reset the switch with this parameter enabled,
the SuperMezz image must be present on the switch.
Configures the switch to use ACLI or CLI mode. After you change this
acli parameter, you must restart the system for the change to take effect. The
default is true.
Activates or disables automatic reboot on a fatal error. The default is
reboot activated. This command is equivalent to the debugmode command. If you
change this parameter, you must reset the switch. Important For internal
Avaya use only. Do not change this parameter unless directed by Avaya.
rlogind Enables the rlogin or the rsh server.
Activates or disables the ability to save the configuration or boot
savetostandby configuration file automatically to the standby SF/CPU. The default is
disabled. If you have a dual SF/CPU system, Avaya recommends that you
enable this flag for ease of operation.
Selects the Multiple Spanning Tree Protocol (MSTP), Rapid Spanning Tree
Protocol (RSTP), or default (legacy) spanning tree modes. If you do not
spanning-tree-mode
<mstp|rstp|default> specify a protocol, the switch uses the default. If you change this
parameter, you must save the current configuration and reset the switch.
The default is rstp.
sshd Enables the ssh daemon.
Activates or disables TFTP server service. The default is disabled. Note that
tftpd when the TFTP server is disabled you can still copy files between the
SF/CPUs.
telnetd Enables the Telnet server.
Activates or disables the creation of trace logs. The default is disabled.
trace-logging Important For internal Avaya use only. Do not change this parameter
unless directed by Avaya.
Activates syntax checking of the configuration file. If a syntax error is
found, the factory default configuration file is loaded. When set to false,
verify-config syntax errors are logged and the SF/CPU continues to source the
configuration file. The default is true. Avaya recommends that you change
this flag to false. If you change this parameter, you must reset the switch.
Activates or disables the hardware watchdog timer, which monitors a
hardware circuit. The watchdog timer reboots the switch based on software
wdt errors. The default for this command is activated. If you change this
parameter, you must reset the switch. Important For internal Avaya use
only. Do not change this parameter unless directed by Avaya.
ftpd Enables the FTP server.
tftpd Enables the TFTP server.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config flags 8616-
reautoneg
Syntax
boot config flags 8616-reautoneg
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
8616- Enables reautonegotiation for 8616 modules. Reautonegotiation permits 8616 modules to
reautoneg reautonegotiate when connected to a Multiservice Switch 15000.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config flags access-
service
Syntax
boot config flags <access-service>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
access- Specifies one of the following remote-access service types to enable:ftpd rlogind
service sshd telnetd tftpd
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config flags block-snmp
Syntax
boot config flags block-snmp
Default
By default, SNMP access is enabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
block- Turns the flag on or off. Use the no operator to remove this configuration. The default is
snmp off. To set this option to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config flags
factorydefaults
Syntax
boot config flags factorydefaults
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
factorydefaults Sets the runtime switch configuration to factory defaults.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config flags ftpd
Syntax
boot config flags ftpd
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
ftpd Enables ftp remote access server.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config flags ha-cpu
Syntax
boot config flags ha-cpu
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
ha-cpu -
ha-cpu Activates or disables High Availability (HA) mode. Switches with two SF/CPUs use HA
mode to recover quickly from a failure of one of the SF/CPUs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config flags spanning-
tree-mode
Syntax
boot config flags spanning-tree-mode {rstp|mstp}
Default
RSTP
Command mode
Global configuration mode
Command parameters
Parameter Description
rstp|mstp Specifies the Spanning Tree modes as Rapid Spanning Tree Protocol (RSTP) or Multiple
Spanning Tree Protocol (MSTP).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config flags sshd
Syntax
boot config flags sshd
Default
None
Command mode
Global configuration mode
Syntax
boot config host
Default
The default is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
Activates or disables debug mode on FTP. If you enable debug mode, debug messages
ftp- display on the management console screen. The default is disabled. Use the no operator
debug to remove this configuration. To set this option to the default value, use the default
operator with the command.
Configures the password to enable FTP transfers. value is the password, up to 16
characters long. After this password is configured, you can use only FTP for remote host
password logon. Important This password must match the password set for the FTP server, or the
<value> FTP operation fails. Also, if the password is set to a nonnull value, all copying to and
from the network uses FTP instead of TFTP. If the user name or password is incorrect,
copying over the network fails.
Activates or disables debug mode on TFTP/TFTPD. If you enable debug mode, debug
tftp- messages display on the management console screen. The default is disabled. Use the
debug no operator to remove this configuration. To set this option to the default value, use the
default operator with the command.
Activates or disables the TFTP hash bucket display. The default is disabled. Use the no
tftp-
hash operator to remove this configuration. To set this option to the default value, use the
default operator with the command.
tftp- Configures the TFTP retransmission timeout. The default value is 2 seconds. seconds is
rexmit the number of seconds (1120). To set this option to the default value, use the default
<seconds> operator with the command.
tftp- Configures the TFTP timeout. The default value is 10 seconds. seconds is the number of
timeout seconds (1120). To set this option to the default value, use the default operator with
<seconds> the command.
user Configures the remote user logon. value is the user logon name, up to 16 characters
<value> long. To set this option to the default value, use the default operator with the command.
ftp- Enables or disables debug mode on FTP. If you enable debug mode, debug messages
debug appear on the management console screen.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config master
Syntax
boot config master <cpu-slot>
Default
The default slot is 5.
Command mode
Global configuration mode
Command parameters
Parameter Description
<cpu-slot> Specifies the slot number for the primary SF/CPU. This variable can be 5 or 6.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config mezz-image
Syntax
boot config mezz-image image-name <Word 0-256>
Default
Command mode
Global configuration mode
Command parameters
Parameter Description
image-name <Word 0-256> Specifies the Mezz-image file name with a string length of 0 to 256.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config mezz-image
image-name
Syntax
boot config mezz-image image-name /flash/p80m5000.img
Default
None
Command mode
Global configuration mode
Syntax
boot config net <cpu-network-port>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<cpu-network-port> Identifies the port using one of the following:mgmt cpu2cpu pccard
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config net mgmt ip
Syntax
boot config net mgmt ip <ipaddr> <mask> <value>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<ipaddr> Specifies the IP address and subnet mask of the management port (For example,
<mask> 10.127.231.15 255.255.255.0).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config net mgmt route
Syntax
boot config net mgmt route <netaddr/mask> <gateway>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
gateway Configures the IP address of the default gateway.
netaddr/mask Configures the IP address and mask of the destination network in the formats
a.b.c.d/x | a.b.c.d/x.x.x.x | default.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config sio modem
Syntax
boot config sio modem 8databits
Default
The default is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
8databits Specifies either 8 (enabled) or 7 (disabled) data bits for each byte for software to
interpret.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot config tz
boot config tz
Configure the time zone to specify the time zone for your location and configure settings for Daylight Saving Time (DST).
Syntax
boot config tz
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Configures the ending date of daylight saving time. You can specify the
time in one of the two ways: Mm.n.d/hhmm specifies an hour on the
dst-end nth occurrence of a weekday in a month. For example, M10.5.0/0200
<Mm.n.d/hhmm|MMddhhmm> means the fifth occurrence of Sunday in the tenth month (October) at
2:00 a.m. MMddhhmm specifies a month, day, hour, and minute. For
example, 10310200 means October 31 at 2:00 a.m.
Configures an abbreviated name for the local daylight saving time zone.
dst-name <dstname> dstname is the name (for example, pdt is Pacific Daylight Time). To set
this option to the default value, use the default operator with the
command.
Configures the daylight saving adjustment in minutes or hours:minutes.
dst-offset The values range from 4:0 to 4:0 for hours:minutes and from 240 to
<minutes|hh:mm> 240 for minutes. The default is 60. To set this option to the default
value, use the default operator with the command.
Configures the starting date of daylight saving time. Mm.n.d/hhmm
specifies an hour on the nth occurrence of a weekday in a month. For
dst-start example, M10.5.0/0200 means the fifth occurrence of Sunday in the
<Mm.n.d/hhmm|MMddhhmm> tenth month (October) at 2:00 a.m. MMddhhmm specifies a month,
day, hour, and minute. For example, 10310200 means October 31 at
2:00 a.m.
Configures an abbreviated name for the local time zone name. tz is the
name <tz> name (for example "pst" is Pacific Standard Time). To set this option to
the default value, use the default operator with the command.
Configures the time zone offset in minutes or hours:minutes to subtract
from Universal Coordinated Time (UTC), where positive numbers mean
offset-from-utc west of Greenwich and negative numbers mean east of Greenwich. The
<minutes|hh:mm> values range from 14:0 to 14:0 for hours:minutes and from 840 to
840 for minutes. The default value is 0. To set this option to the
default value, use the default operator with the command.
Configures the ending date of DST. You can specify the time in one of
two ways: Mm.n.d/hhmm specifies an hour on the nth occurrence of a
dst-end weekday in a month. For example, M10.5.0/0200 means the fifth
<Mm.n.d/hhmm|MMddhhmm> occurrence of Sunday in the tenth month (October) at 2:00 a.m.
MMddhhmm specifies a month, day, hour, and minute. For example,
10310200 means October31 at 2:00 a.m.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:boot file config value
Syntax
boot [<file>] [config <value>] [-y]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Specifies the software image device and file name in the format: [a.b.c.d:]<file>
file /pcmcia/<file> /flash/<file>. The file name, including the directory structure, can include
up to 99 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:brouter port
brouter port
Configure Ethernet ports on the Ethernet Routing Switch 8800/8600 to assign one of two port types: access or trunk.
Syntax
brouter port <portList> [vlan <1-4094>] [subnet <A.B.C.D/0-32>] [mac_offset <0-65535>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
mac_offset <0- mac_offset is a user-assigned MAC address that you can use in place of the
65535> default MAC address.
subnet
<A.B.C.D/0-32> Specifies the IP address and subnet mask.
port <portList> Indicates the slot and port number of the port you are configuring.
vlan <1-4094> Specifies the VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:cfm ethertype
cfm ethertype
Use this command to configure the CFM ethertype.
Syntax
cfm ethertype <ethertype>
Default
None
Command mode
Global configuration mode
cfm maintenance-association
Create the CFM MA.
Syntax
cfm maintenance-association <md-name> <ma-name> [index <value>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<md-name> Specifies the MD name in a string of 122 characters.
<ma-name> Specifies the MA name in a string of 122 characters.
index <value> Specifies a maintenance association entry index. Range is 12147483647.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:cfm maintenance-domain
cfm maintenance-domain
Create the CFM MD.
Syntax
cfm maintenance-domain <md-name> create [index <value>] [maint-level <value>] [level
<value>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<md-name> Specifies the MD name in a string of 122 characters.
index <value> Specifies a maintenance domain entry index. Range is 12147483647.
maint-level <value> Specifies the MD maintenance level when creating the MD. Range is 07.
level <value> Modifies the MD maintenance level for an existing MD. Range is 07.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:cfm maintenance-endpoint
cfm maintenance-endpoint
Create the CFM MEP.
Syntax
cfm maintenance-endpoint <md-name> <ma-name> <mepID> [state {enable|disable}]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<md-name> Specifies the MD name in a string of 122 characters.
<ma-name> Specifies the MA name in a string of 122 characters.
<mepID> Specifies the MEP ID. Range is 18191.
state {enable|disable} Enables or disables the MEP when creating the MEP.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clear filter
clear filter
Clear ACE for each-port statistics.
Syntax
clear filter acl statistics port[<1-4096>][<portList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[<1-4096>] Specifies the ACL ID.
[<portList>] Specifies the ports for which you want to see statistics.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clear filter acl
Syntax
clear filter acl statistics default[<1-4096>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[<1-4096>] Specifies the ACL identifier.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clear ip arp interface
Syntax
clear ip arp interface [fastethernet|gigabitethernet|vlan<1-4094>] <portList>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
interface-id ID of the interface.
interface-type Type of interface, either a port or a VLAN.
<fastethernet|gigabitethernet|vlan <1-4094> Specifies the interface to be cleared.
portlist Specifies the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clear ip igmp igap-counters
Syntax
clear ip igmp igap-counters [vlan <1-4094>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Specifies the VLAN ID. The value ranges from 1 to 4094.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clear ip ipfix
clear ip ipfix
Clear the exporter and hash statistics configuration on the specified slot.
Syntax
clear ip ipfix {[stats [slots]]}
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
stats [slots] Clears the statistics on the specifies slot.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clear ip msdp peer
Syntax
clear ip msdp peer <A.B.C.D>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
A.B.C.D Specifies the IP address of the MSDP peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clear ip msdp sa-cache
Syntax
clear ip msdp sa-cache [group <A.B.C.D>] [peer <A.B.C.D>] [rp <A.B.C.D>] [source
<A.B.C.D>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
group
<A.B.C.D> Optionally, clears the SA entries that match the specified group range.
peer <A.B.C.D> Optionally, clears only the entries the router learns from the peer address you
specify.
rp <A.B.C.D> Optionally, clears the SA cache entries that match the specified RP address.
source
<A.B.C.D> Optionally, clears the SA cache entries that match the specified source range.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clear ip msdp statistics
Syntax
clear ip msdp statistics {A.B.C.D}
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
peer address {A.B.C.D} The IP address of the MSDP peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clear ip route interface
Syntax
clear ip route interface [fastethernet|gigabitethernet|vlan <1-4094>]<portList>
Default
None
Command mode
Privileged EXEC mode
clear ip traffic-filter
Clear traffic filter statistics to delete statistics you no longer require.
Syntax
clear ip traffic-filter-statistics [<1-4096>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4096> Specifies the filter ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clear ipv6 vrrp
Syntax
clear ipv6 vrrp {fastethernet <slot|port>| gigabitethernet <slot|port>| vlan <vid>} vrid
<value>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
{fastethernet <slot|port>|gigabitethernet Specifies the port or VLAN for which
<slot|port>|vlan <vid>} to clear statistics.
[vrid <1255>] Specifies the virtual router ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clear isis lsdb
Syntax
clear isis lsdb
Default
None
Command mode
Privileged EXEC mode
Syntax
clear isis stats [error-counters][packet-counters]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[error-counters] Clears the error count statistics.
[packet-counters] Clears the packet count statistics.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clear khi all
Syntax
clear khi all
Default
None
Command mode
Global configuration mode
Syntax
clear khi chassis
Default
None
Command mode
Global configuration mode
Syntax
clear khi forwarding
Default
None
Command mode
Global configuration mode
clear khi ip
Use this command to clear IP interface KHI statistics.
Syntax
clear khi ip
Default
None
Command mode
Global configuration mode
Syntax
clear khi log
Default
None
Command mode
Global configuration mode
Syntax
clear khi performance
Default
None
Command mode
Global configuration mode
Syntax
clear khi port
Default
None
Command mode
Global configuration mode
Syntax
clear khi protocol
Default
None
Command mode
Global configuration mode
Syntax
clear radius statistics
Default
None
Command mode
Privileged EXEC mode
Syntax
clear wireless-switch mac-address-entry [vid <value>] [mac <value>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[vid Clears information for all of the FDB entries configured on this switch or for a specific
<value>] VLAN ID.
[mac Clears information for all of the FDB entries configured on this switch or for a specific
<value>] MAC address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clear wireless-switch
statistics
Syntax
clear wireless-switch statistics [<tunnelIdList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<tunnelIntfId> Clears all the tunnel statistics on the switch or for a specific tunnel.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clilog
clilog
When enabled, ACLI logging keeps track of all command line interface commands executed on the switch. Use ACLI logging for
fault management purposes.
Syntax
clilog enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables ACLI logging. To disable, use the no clilog enable command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clilog enable
clilog enable
Configure logging of ACLI commands to the file clilog.txt on the PCMCIA. You can enable command logging to keep track of the
commands a user enters during a logon session.
Syntax
clilog enable [maxfilesize <integer>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Activates ACLI logging to the file clilog.txt on the PCMCIA, To disable ACLI logging, use
the no form of the command, no clilog enable.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:cli password
cli password
Change passwords after an upgrade to maintain the highest security levels.
Syntax
cli password <WORD 1-20> read-only
Default
Command mode
Global configuration mode
Command parameters
Parameter Description
read-write-access
<WORD 0-20> Changes the read-write access logon or password or both.
Word <1-20> Specifies the logon user name.
read-only Change read only logon ID and password or both. For more password
options, enter cli password <WORD 1-20> ?
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clock set
clock set
Configure the calendar time in the form of month, day, year, hour, minute, and second.
Syntax
clock set <MMddyyyyhhmmss>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<MMddyyyyhhmmss> Specifies the format of date in the form of month, day, and year and time in
the form of hours, minutes, and seconds.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clock source
clock source
Configure the clock source type in WAN modules.
Syntax
clock source <internal|line>
Default
The default value is internal.
Command mode
Global configuration mode
Command parameters
Parameter Description
internal This mode uses the recovered Receive (Rx) clock to generate the Tx clock.
line This mode uses the onboard oscillator to generate the transmit (Tx) clock. Only
applicable to WAN 10 Gbit/s ports.
port
[portlist] Specifies the slot and the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:clock sync-time
clock sync-time
Configure the regular interval to synchronize the real-time and system clocks.
Syntax
clock sync-time <15-3600>
Default
The default value is 60.
Command mode
Global configuration mode
Command parameters
Parameter Description
sync- Configures the real-time clock to the system clock synchronization time in minutes. <15-
time 3600> specifies the number of minutes between synchronization. The switch generates
<15- log messages if the drift between the real-time clock and the system clock is more than 5
3600> seconds.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:comp-bestpath-med-confed
comp-bestpath-med-confed
When enabled, compares multiexit discriminator (MED) attributes within a confederation.
Syntax
comp-bestpath-med-confed enable
Default
The default value is enable.
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables and compares multiexit discriminator attributes within a BGP confederation.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:copy
copy
Copy packets to a remote machine, or the switch flash or PCMCIA. If PCAP is used with autosave disabled, captured packets are
stored in the Secondary SF/CPU DRAM buffer. Copy files to a safe place. Copy files as part of an upgrade procedure to back up
files or to move files to another location.
Syntax
copy <file WORD 1-99> <file WORD 1-99>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Specifies pcmcia, flash, or an IP host by IP address and specifies the PCAP file (.cap).
<WORD 1- Formats include:a.b.c.d:<file> /pcmcia/<file> /flash/<file> /{wsm|sam} <1-10> [<dst-
99> target>] where dst-target is {image1|image2|boot|cfg} for the WSM or {image|cfg} for
the SAM.
Word <1- Specifies the source file to be copied.
99>
Word <1- Specifies the destination file.
99>
file
WORD 1- Specifies the source file name to be copied.
99
file
WORD 1- Specifies the destination file name.
99
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:copy srcfile destfile
Syntax
copy <a.b.c.d>:<srcfile> /flash/<destfile>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<a.b.c.d> Specifies the IP address of the TFTP server where the license file is to be copied from.
Specifies the name of the license file when copied to the flash. The destination file
<destfile> name must be lower case and have a file extension of .dat. For example,
bld100_8610adv.dat or license.dat.
<srcfile> Specifies the name of the license file on the TFTP server. For example,
bld100_8610adv.lic or license.dat.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:cp-limit port multicast-limit
Syntax
cp-limit port [multicast-limit <value>] [broadcast-limit <value>]
Default
The default is 1500.
Command mode
FastEthernet or GigabitEthernet Interface configuration mode
Command parameters
Parameter Description
multicast- Configures the multicast control frame rate. The range is 1000100000 pps. To set
limit
<value> this option to the default value, use the default operator with the command.
port Specifies a port or list of ports. To set this option to the default value, use the
default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:csnp-interval
csnp-interval
Specify the Complete Sequence Number Packet (CSNP) interval in seconds. This is a system level parameter that applies for L1
CSNP generation on all interfaces.
Syntax
[no] [default] csnp-interval <csnp-interval>
Default
Default value is 10.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value of 10.
default Use the default option to set this parameter to the default of 10.
<csnp- Specifies the CSNP interval in seconds. This is a system level parameter that applies for
interval> L1 CSNP generation on all interfaces. Range is 1600.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:debug ip pim
debug ip pim
Use PIM traces to aid in PIM troubleshooting.
Syntax
debug ip pim pimdbgtrace
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
pimdbgtrace Enables or disables PIM debug traces.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:debug-screen
debug-screen
Displays debug messages on the console, or saves them in a log file.
Syntax
debug-screen <off|on>
Default
The default value is off.
Command mode
Global configuration mode
Command parameters
Parameter Description
<on|off> Disable BGP screen logging (off) or enable BGP screen logging (on).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:debug spbm isis recompute-
fib
Syntax
debug spbm isis recompute-fib
Default
None
Command mode
User EXEC mode
Syntax
debug spbm isis recompute-fib-download
Default
None
Command mode
User EXEC mode
Syntax
debug spbm l2vpn action-call index <value>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
index <value> Enter an index value of 114.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:debug spbm l2vpn event-
notify
Syntax
debug spbm l2vpn event-notify event <value>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
event <value> Enter an event value, range of 08.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:debug spbm l2vpn fib-
update
Syntax
debug spbm l2vpn fib-update
Default
None
Command mode
Privileged EXEC mode
Syntax
debug spbm l2vpn fib-update-cvlan c-vid <vid>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
c-vid <vid>] Enter the C VLAN ID, vid range of 1 - 4094.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:default-information
default-information
Enables the advertisement of a default route to peers, if it is present in the routing table.
Syntax
default-information originate
Default
The default value is disable.
Command mode
Global configuration mode
Command parameters
Parameter Description
originate Enables the origination default route.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:default ip
default ip
Syntax
Default
Command mode
Global configuration mode
Syntax
Default
The default value is disable.
Command mode
VLAN Interface configuration code
Syntax
Default
None
Command mode
VLAN Interface configuration code
default-metric (BGP)
Sets a value that is sent to a BGP neighbor to determine the cost of a route a neighbor is using.
Syntax
default-metric <-1-2147483647>
Default
The default value is -1.
Command mode
Global configuration mode
default-metric (RIP)
Set RIP Default Import Metric. This value is used by rip announce of OSPF internal routes if the policy does not specify metric. 0 is
used for deconfiguration.
Syntax
default-metric <0-15>
Default
The default value is 8.
Command mode
Global configuration mode
dir
View the free space and files in flash memory.
Syntax
dir -l
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
-l Displays all the details of all the files like name, size and time and date of the file
created.
Word <1-
99> Specifies the name of the particular file to view details.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:dos-format
dos-format
Format the flash or PCMCIA.
Syntax
dos-format [/flash][/pcmcia]
Default
Command mode
Global configuration mode
Command parameters
Parameter Description
/flash Formats flash.
/pcmcia Formats PCMCIA.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:dsapssap
dsapssap
Configure the multiple DSAP and SSAP to create a protocol-based VLAN.
Syntax
dsapssap <0x0-0xffff>
Default
None
Command mode
Global configuration mode
dump ar
To aid in troubleshooting, a dump of the hardware records from an ingress OctaPID can be captured.
Syntax
dump ar <0-64> <WORD 1-1536> <0-3>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<0-64> Specifies the OctaPID assignment from 1 to 64.
<WORD 1- Specifies a record type in the AR table. Options include vlan, ip_subnet, mac_vlan, mac,
1536> arp, ip, ipmc, ip_filter, protocol, sys_rec, all.
<0-3> Specifies the verbosity from 0 to 3. Higher numbers specify more verbosity.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:dump ercd record
Syntax
dump ercdRecord {arp <slot> | ip <slot>| ip_subnet <slot/port>| mac <slot>| mac_vlan
<slot/port> | mgid <slot> | protocol <slot/port> | vlan <slot/port>} [verbose <value>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
arp Specifies ARP ERCD records.
ip Specifies IP ERCD records.
ip-subnet Specifies IP subnet ERCD records.
Specifies MAC ERCD records. Displays the learned MAC entries for the specified
mac port that are present on the COP and the corresponding VLAN record of the
port to check if the MAC entry learned against one port is downloaded properly
to all available slots.
mac_vlan Specifies MAC VLAN ERCD records.
mgid Specifies MGID ERCD records.
protocol Specifies protocol ERCD records.
vlan Specifies VLAN ERCD records. Displays the VLANS to which this port belongs
and the corresponding ingress VLAN records of this port.
<slot> Specifies the slot number to which you send the query.
<slot/port> Specifies the port number {slot/port} for which you get the records.
[verbose<value>] Specifies an expanded display. valueis in the range of 03.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:dump rsp-trace egress-
display-pkt
Syntax
dump rsp-trace egress-display pkt <slot/port> <pkt-id>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<slot/port> Specifies a port in the lane for which to display the trace.
<pkt-id> Specifies the ID as an integar of the packet to display.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:dump rsp-trace ingress-pkt-
trace
Syntax
dump rsp-trace ingress-pkt-trace <slot/port> [<start-pkt><end-pkt>]
Default
None
Command mode
Global configuration mode
duplex
Configure the duplex mode on the Ethernet module. This is applicable to 10/100/1000 Mbit/s ports.
Syntax
duplex [port <portList>] <half|full>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<half|full> Specifies half- or full-duplex mode. 1 and 10 Gbit/s ports must use full-duplex mode.
port Specifies the slot and the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:eapol enable
eapol enable
Configure EAPoL on the Avaya Ethernet Routing Switch 8800/8600.
Syntax
eapol enable
Default
None
Command mode
Global configuration mode
eapol port
Configure EAPoL on a specific port when you do not want EAPol applied to all of an Avaya Ethernet Routing Switch 8800/8600.
Syntax
eapol port <portlist>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the port or list of ports used by EAPol. Specify the
<portlist> port list using the following format: {slot/port[-slot/port][,
...]}.
max-request <1-10> Maximum EAP requests sent to supplicant before timing out
the session.
quiet-interval <1-65535> Time interval in seconds between authentication failure and
start of a new authentication.
re-authentication enable Enables reauthenticating an existing supplicant at a specified
time interval.
re-authentication-period <1- Time interval in seconds between successive
2147483647> reauthentications.
server-timeout <1-65535> Time in seconds to wait for a response from RADIUS server.
sess-manage-mode enable Enables the port session to be managed by an external
device.
sess-manage-open-immediate Sets the port to be opened immediately after 8021x
enable authentication.
status
{authorized|auto|unauthorized} Set the desired EAP authentication status for this port.
supplicant-timeout <1-65535> Time in seconds to wait for response from supplicant for all
EAP packets except EAP Request/Identity.
traffic-control {in|in-out} Desired level of traffic control of port.
transmit-interval <1-65535> Time in seconds to wait for response from supplicant for
EAP Request/Identity packets.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:eapol sess-manage enable
Syntax
eapol sess-manage enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
sess-manage enable Enables the session management on EAPoL.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:eapol status
eapol status
Enable EAPoL on an interface.
Syntax
eapol status {authorized|auto|unauthorized}
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
authorized Specifies the port is always authorized.
auto Specifies that port authorization depends on the results of the EAPoL authentication
by the RADIUS server.
unauthorized Specifies the port is always unauthorized.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:eapol status auto
Syntax
eapol status auto
Default
None
Command mode
Global configuration mode
Syntax
eapol status unauthorized
Default
None
Command mode
Global configuration mode
enable
Enables the WSP. Use the no enable or default enable options to disable the WSP.
Syntax
enable
Default
disable
Command mode
WLAN Switch Configuration
enable-diffserve
Enable DiffServ so that the switch provides DiffServ-based QoS on that port.
Syntax
enable-diffserv [port <portList>] [enable]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Enables DiffServ for the specified port. The default is disabled. To use the default
enable configuration, use the default option in the command default enable-diffserv [enable]
To delete the current configuration, use the no option in the command no enable-
diffserv [enable]
port Specifies the slot and port, or slot and port list. To delete the current configuration, use
<portList> the no option in the command no enable-diffserv [port <portList>]
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:encapsulation dot1q
encapsulation dot1q
Enable tagging on the ports before configuring Untagged VLANs.
Syntax
encapsulation dot1q
Default
None
Command mode
Global configuration mode
end
Takes you back to the next lowest mode.
Syntax
Default
None
Command mode
All modes
exit
Takes you back to Priviledged EXEC mode.
Syntax
Default
None
Command mode
All modes
filter acl
Configure access control lists (ACL) to create rules for the ACT.
Syntax
filter acl <1-4096> type <inVlan|outVlan|inPort|outPort> act <1-4096> [pktType <ipv4|ipv6>]
[name <WORD 0-32>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
acl-id Specifies an ACL ID in the range 14096.
act <act-id> Specifies the ACT ID to associate with the ACL.
enable Enables the ACL state along with all of the ACEs below it.
Enable is the default state for the ACL.
name <word> Renames an ACL. To set this option to the default value,
use the default operator with the command.
Configures the packet type for the ACL.Important The
pktType <ipv4|ipv6> pktType field is optional for IPv4 traffic filters. It is required
if you apply the ACL to IPv6 packets. The default is IPv4.
act <1-4096> Specifies an ACT ID from 1 to 4096.
name <WORD 0-32> Specifies an optional descriptive name for the ACL.
type Specifies the ACL type. inVlan and inPort are ingress ACLs,
<inVlan|outVlan|inPort|outPort> and outVlan and outPort are egress ACLs.
<1-4096> Specifies a unique identifier (1 to 4096) for this ACL.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter acl ace
Syntax
filter acl ace <1-4096> <1-1000> [name <WORD 0-32]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
name <WORD 0-32> Specifies an optional descriptive name for the ACE that uses 032 characters.
<1-4096> Specifies the ACL ID in the range of 1 to 4096.
<1-1000> Specifies the Access Control Entry (ACE) id in the range of 0 to 1000.
name <WORD 0-32> Specifies the name for the ACE in the range of 0 to 32 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter acl ace action
Syntax
filter acl ace action <1-4096> <1-1000> {deny|permit} [ipfix |enable|disable]
Default
The default is deny.
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-4096> Specifies an ACL ID in the range of 14096.
<1-1000> Specifies an ACE ID in the range of 11000.
{deny|permit} Configures the action mode, and its options update desired action parameters for
access control entries.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter acl ace advanced
Syntax
filter acl ace advanced <1-4096> <1-1000>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
custom- Creates a custom filter 1:<WORD 0-32> specifies a descriptive name for the pattern
filter1 that uses 032 characters. <eq|le|ge> specifies the operators equal to, less than or
<WORD 0-32> equal to, or greater than or equal to. The ace-op ne does not apply to an ACE
<eq|le|ge>
<WORD 1- pattern. <WORD 1-1024> specifies a hexadecimal number equal to the pattern
1024> template length.
custom-
filter2
<WORD 0-32> Creates custom filter 2.
<eq|le|ge>
<WORD 1-
1024>
custom-
filter3
<WORD 0-32> Creates custom filter 3.
<eq|le|ge>
<WORD 1-
1024>
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter acl ace arp
Syntax
filter acl ace arp <1-4096> <1-1000> operation eq <arprequest|arpresponse>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
operation eq Specifies an ARP operation type of arpRequest or arpResponse. For
<arprequest|arpresponse> ARP, only one operator and attribute exist (eq and operation).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter acl ace debug
Syntax
filter acl ace debug <1-4096> <1-1000> [count enable] [copy-to-primary-cp enable] [copy-
to-secondary-cp enable] [mirror enable] [monitor-dst-ports <portList>] [monitor-dst-vlan
<1-4094>] [monitor-dst-mlt <1-256>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
copy-to- Enables the ability to copy matching packets to the primary (Master) CPU. The default
primary- is disabled. To use the default configuration, use the default option in the command
cp enable default filter acl ace debug <1-4096> <1-1000> copy-to-primary-cp enable
Enables the ability to copy matching packets to the secondary (Standby) CPU. The
copy-to- default is disabled. To use the default configuration, use the default option in the
secondary-
cp enable command default filter acl ace debug <1-4096> <1-1000> copy-to-secondary-cp
enable
Enables the ability to count matching packets. The default is disabled. To use the
count
enable default configuration, use the default option in the command default filter acl ace
debug <1-4096> <1-1000> count enable
Enables mirroring. If you enable mirroring, ensure that you configure the appropriate
parameters: For R and RS modules in Rx mode, and for RS modules, usemonitor-dst-
mirror ports, monitor-dst-vlan, or monitor-dst-mlt. For R modules in Tx mode, use the mirror-
enable by-port commands to specify the mirroring source or destination. The default is
disabled. To use the default configuration, use the default option in the command
default filter acl ace debug <1-4096> <1-1000> mirror enable
monitor-
dst-ports Configures mirroring to a destination port or ports.
<portList>
monitor-
dst-mlt Configures mirroring to a destination MLT group.
<1-256>
monitor-
dst-vlan Configures mirroring to a destination VLAN.
<1-4094>
copy-to-
primary- Enables the ability to copy matching packets to the primary (Master) CPU.
cp enable
copy-to-
secondary- Enables the ability to copy matching packets to the Secondary CPU.
cp enable
count
enable Enables the ability to count matching packets.
Enables mirroring. If you enable mirroring, ensure that you configure the appropriate
mirror parameters: For R and RS modules in Rx mode: monitor-dst-ports, monitor-dst-vlan, or
enable monitor-dst-mlt. For R modules in Tx mode: use the mirror-by-port commands to
specify the mirroring source/destination.
monitor-
dst-ports Configures mirroring to a destination port or ports.
<portList>
monitor-
dst-mlt Configures mirroring to a destination MLT group.
<1-256>
monitor-
dst-vlan Configures mirroring to a destination VLAN.
<1-4094>
<1-4096> Specifies the ACL ID from 1 to 4096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter acl ace ethernet
Syntax
filter acl ace ethernet <1-4096> <1-1000>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
The <eq|ne|le|ge> parameter specifies an operator for a field match condition:
dst-mac equal to, not equal to, less than or equal to, greater than or equal to. The <WORD
<eq|ne|le|ge>
<WORD 1- 1-1024> parameter specifies a list of destination MAC addresses separated by a
1024> comma, or a range of MAC addresses specified from low to high; for example,
[a:b:c:d:e:f, (x:y:z:w:v:u-a:b:c:d:e:f)].
The <eq|ne> parameter specifies an operator for a field match condition: equal to
ether-type or not equal to. The <WORD 1-200> parameter specifies an ether-type name or
<eq|ne>
<WORD 1-200> number: 065563 ip, arp, appleTalk, decLat, decOther, sna802dot2, snaEthernet2,
netBios, xns, vines, ipv6, rarp, or PPPoE
port eq
<portList> Specifies ports to which to match, where <portList> specifies the ports.
The <eq|ne|le|ge> parameter specifies an operator for a field match condition:
src-mac equal to, not equal to, less than or equal to, greater than or equal to. The <WORD
<eq|ne|le|ge>
<WORD 1- 1-1024> parameter specifies a list of source MAC addresses separated by separated
1024> by a comma, or a range of MAC addresses specified from low to high; for example,
[a:b:c:d:e:f, (x:y:z:w:v:u- a:b:c:d:e:f)].
vlan-id eq
<1-4094> Specifies VLANs to match, where <1-4094> specifies the VLAN IDs.
vlan-tag- The <eq|ne> parameter specifies an operator for a field match condition: equal to
prio <eq|ne> or not equal to. The <vlan-tag-prio> parameter specifies a VLAN tag priority from
<0-7> 07 or undefined.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter acl ace ip
Syntax
filter acl ace ip <1-4096> <1-1000> dst-ip eq <Word 1-1024>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
The <eq|ne|le|ge> parameter
specifies an operator for a field
match condition: equal to, not
equal to, less than or equal to,
greater than or equal to. The
dst-ip <eq|ne|le|ge> <WORD 1-1024> <WORD 1-1024> parameter
specifies the destination IP
address list in one of the
following formats: a.b.c.d,
[w.x.y.z-p.q.r.s], [l.m.n.o/mask],
[a.b.c.d/len].
The <eq|ne> parameter specifies
an operator for a field match
condition: equal to or not equal
to. The <WORD 0-256>
parameter specifies the PHB
name or DSCP value {0 to 256},
dscp <eq|ne> <WORD 0-256> or phbcs0, phbcs1, phbaf11,
phbaf12, phbaf13, phbcs2,
phbaf21, phbaf22, phbaf23,
phbcs3, phbaf31, phbaf32,
phbaf33, phbcs4, phbaf41,
phbaf42, phbaf43, phbcs5,
phbcs6, phbef, or phbcs.
The eq parameter specifies an
operator for a field match
condition: equal to. The ip-frag-
ip-frag-flag eq
<noFragment|anyFragment|moreFragment|lastFragment> flag parameter specifies a match
option for IP fragments (0, 2, or
4), or noFragment, anyFragment,
moreFragment, lastFragment.
ip-options any Matches to an IP option. Any is
the only option.
The <eq|ne> parameter specifies
an operator for a field match
condition: equal to or not equal
to. The <WORD 1-256>
ip-protocol-type <eq|ne> <WORD 1-256> parameter specifies one or more
IP protocol types: (1256), or
undefined, icmp, tcp, udp,
ipsecesp, ipsecah, ospf, vrrp,
snmp.
The <eq|ne|le|ge> parameter
specifies an operator for a field
match condition: equal to, not
equal to, less than or equal to,
src-ip <eq|ne|le|ge> <WORD 1-1024> greater than or equal to. The
<WORD 1-1024> parameter
specifies a source IP address list
in one of the following formats:
a.b.c.d, [w.x.y.z-p.q.r.s],
[l.m.n.o/mask], [a.b.c.d/len].
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter acl ace ipv6
Syntax
filter acl ace ipv6 <1-4096> <1-1000>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
ace-id Specifies an ACE ID in the range 11000. To set this option to the default value, use the
default operator with the command.
acl-id Specifies an ACL ID in the range 14096. To set this option to the default value, use the
default operator with the command.
dst-ipv6 Specifies the following: an operator for a field match condition-eq the list of destination
eq
<word> IPv6 addresses separated by commas
nxt-hdr Specifies the following: an operator for a field match condition (eq | ne) the next header
<eq|ne> value from one of the following: fragment|hop-by-
<nxt-
hdr> hop|icmpv6|ipsecah|ipsecesp|noHdr|routing|tcp|udp| undefined
src-ipv6 Specifies the following: an operator for a field match condition-eq the list of source IPv6
eq
<word> addresses separated by commas
dst-ipv6 The <eq|ne> parameter specifies an operator for a field match condition: equal to or not
<eq>
<WORD 0- equal to. The <WORD 0-255> parameter specifies a list of destination IPv6 addresses,
255> separated by commas. An example IPv6 address is 3ffe:1900:4545:3:200:f8ff:fe21:67cf.
nxt-hdr The <eq|ne> parameter specifies an operator for a field match condition: equal to or not
<eq|ne> equal to. <nxt-hdr> specifies hop-by-hop, tcp, udp, routing, fragment, ipsecesp, ipsecah,
<nxt-
hdr> icmpv6, noHdr, or undefined.
src-ipv6 The <eq|ne> parameter specifies an operator for a field match condition: equal to or not
<eq>
<WORD 0- equal to. The <WORD 0-255> parameter specifies a list of source IPv6 addresses,
255> separated by commas. An example IPv6 address is 3ffe:1900:4545:3:200:f8ff:fe21:67cf.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter acl ace protocol
Syntax
filter acl ace protocol <1-4096> <1-1000> icmp-msg-type eq <Word 1-200>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the icmp message type attribute of the protocol. The <eq|ne> parameter
specifies an operator for a field match condition: equal to or not equal to. The
icmp-msg- <WORD 1-200> parameter specifies one or more IP protocol types (0255), or
type <eq|ne>
<WORD 1-200> echoreply, destunreach, sourcequench, redirect, echo-request, routeradv,
routerselect, time-exceeded, param-problem, timestamp-request, timestamp-reply,
addressmask-request, addressmask-reply, or traceroute.
The <eq|ne|le|ge> parameter specifies an operator for a field match condition:
tcp-dst-port equal to, not equal to, less than or equal to, greater than or equal to. The <WORD
<eq|ne|le|ge>
<WORD 1-60> 1-60> parameter specifies the destination port for the TCP protocol: (065535), or
echo, ftpdata, ftpcontrol, ssh, telnet, dns, http, bgp, hdot323, or undefined.
tcp-flags Specifies matchAny or matchAll operators for a field match condition. The <WORD>
<match- parameter specifies one or more TCP flags: none, fin, syn, rst, push, ack, urg,
any|match-
all> <WORD> undefined. The tcp-flags and icmp-msg-type command options support lists.
tcp-src-port The <eq|ne|le|ge> parameter specifies an operator for a field match condition:
<eq|ne|le|ge> equal to, not equal to, less than or equal to, greater than or equal to. The <WORD
<WORD 0- 0-65535> parameter specifies the destination port for the TCP protocol (065535),
65535> or echo, dns, bootpServer, bootpClient, tftp, rip, rtp, rtcp, or undefined.
The <eq|ne|le|ge> parameter specifies an operator for a field match condition:
udp-dst-port equal to, not equal to, less than or equal to, greater than or equal to. The <WORD
<eq|ne|le|ge>
<WORD 1-200> 1-200> parameter specifies the destination port for the UDP protocol (065535), or
echo, dns, bootpServer, bootpClient, tftp, rip, rtp, rtcp, or undefined.
udp-src-port The <eq|ne|le|ge> parameter specifies an operator for a field match condition:
<eq|ne|le|ge> equal to, not equal to, less than or equal to, greater than or equal to. The <WORD
<WORD 0- 0-65535> parameter specifies the source port for the UDP protocol (065535), or [
65535> ].
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter acl enable
Syntax
filter acl <1-4096> enable
Default
The default state is enable.
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-4096> Specifies the ACL ID in the range of 1 to 4096.
enable Enables the ACL state, and all associated ACEs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter acl port
Syntax
filter acl port <1-4096> <portList>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
acl-id Specifies an ACL ID in the range 14096.
port Associates a port or a port list with a particular ACL. Format a list of ports separated by
a comma or a range of ports specified as low-high [slot/port -slot/port].
<1-4096> Specifies an ACL ID from 14096.
<portList> Specifies ports in one of the following formats: [<slot/port>] or [<slot/port-slot/port>].
<1-4096> Specifies the ACE ID in the range of 1 to 4096.
portlist Associates a port or a portlist to a particular ACL.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter acl set
Syntax
filter acl set <1-4096> {default-action {deny|permit} global-action {mirror|count|mirror-
count|ipfix|mirror-ipfix|count-ipfix|mirror-count-ipfix}}
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
acl-id Specifies an ACL ID in the range of 14096.
Specifies the default action when no ACEs match. Permitted
default-action <value> options include [deny|permit], with a default of permit. To set this
option to the default value, use the default operator with the
command.
default-action The options are deny or permit.
filter acl set This is the ACL ID. The range is from 14096.
global-action The value is one of the following actions:mirror|count|mirror-
count|ipfix|mirror-ipfix|count-ipfix|mirror-count-ipfix
Specifies the global action for matching ACEs: mirror, count,
mirror-count, ipfix, mirror-ipfix, count-ipfix, or mirror-count-ipfix.
global-action If you enable mirroring, ensure you specify the source or
<count|count- destination mirroring ports: For R modules in Tx mode, use
ipfix|ipfix|mirror|mirror- mirror-by-port commands to specify mirroring ports. For RS
count|mirror-count- modules, or R modules in Rx mode, use the filter acl ace debug
ipfix|mirror-ipfix> commands to specify mirroring ports. The default is none. To use
the default configuration, use the default option in the command
default filter acl set <1-4096> global-action
Specifies the global action to take for matching ACEs: mirror,
global-action count, mirror-count, ipfix, mirror-ipfix, count-ipfix, or mirror-
<count|count- count-ipfix. If you enable mirroring, ensure you specify the source
ipfix|ipfix|mirror|mirror- and/or destination mirroring ports: For R modules in Tx modes:
count|mirror-count- use mirror-by-port commands to specify mirroring ports. For R
ipfix|mirror-ipfix> and RS modules in Rx modes: use the filter acl ace debug
commands to specify mirroring ports.
<1-4096> Specifies an ACL ID from 1 to 4096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter acl set default-action
Syntax
filter acl set <1-4096> default-action <permit|deny>
Default
The default is permit.
Command mode
Global configuration mode
Command parameters
Parameter Description
default-action Specifies the default action to take when no ACEs match. Options
<deny|permit> include <deny|permit>.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter acl vlan
Syntax
filter acl vlan <1-4096> <1-4094>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
acl-id Specifies an ACL ID in the range of 14096. To set this option to the default value, use
the default operator with the command.
Associates a VLAN or a VLAN list with a particular ACL. Format a list of VLANs separated
vlan-id by a comma or a range of VLANs specified as low-high [vlan-id -vlan-id]. To set this
option to the default value, use the default operator with the command.
<1-4096> Specifies an ACL ID from 14096.
<1-4094> Specifies the VLAN IDs from 14094.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter act
filter act
Configure an access control template (ACT) to create, delete, apply, and specify attributes. After you apply the ACT you cannot
change the attributes.
Syntax
filter act <act-id>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies an ACT ID in the range 14096.Important In the Avaya Ethernet Routing Switch
act-id 8800/8600, act-id acts as an index to the ACT table. Thus, you can change the name at
any time, even after you apply it. To set this option to the default value, use the default
operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter act name
Syntax
filter act <1-4096> [name <WORD 0-32>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-4096> Specifies an ACT ID in the range of 1 to 4096.
name Specifies an optional name for the ACT that uses 032 characters. If you do not enter a
<WORD 0- name, the switch generates a default name. You can change the name at any time, even
32> after you issue the apply command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter act pattern
Syntax
filter act pattern <1-4096> <WORD 0-32> <base> <0-76800> <1-56>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
act-id Specifies an ACT ID in the range of 14096.
Adds a template for patterns you create. Options here include: base: the base and the
offset together determine the beginning of the pattern. Permitted values for the base
include the following: ether-begin mac-dst-begin mac-src-begin ethTypeLen-begin arp-
<base> begin ip-hdr-begin ip-options-begin ip-payload-begin ip-tos-begin ip-proto-begin ip-src-
<offset> begin ip-dst-begin ipv6-hdr-begin tcp-begin tcp-srcport-begin tcp-dstport-begin tcp-
<length> flags-end udp-begin udp-srcport-begin udp-dstport-begin ether-end ip-hdr-end icmp-
msg-begin tcp-end udp-end offset: the number of bits from the base where the pattern
starts. This is a range from 076800. length: the length in bits of the user-defined field
from 156.
name Renames the pattern with a new name that you define. Each of the three patterns must
<pattern-
name> use a unique name.
word Specifies a name for the pattern in the range of 132 characters. To set this option to
the default value, use the default operator with the command.
<0- The <0-76800> parameter specifies the offset: the number of bits from the base where
76800> the pattern starts.
<1-56> The <1-56> parameter specifies the length in bits of the user-defined field from 156.
The <base> parameter specifies the base. The base and the offset together determine
the beginning of the pattern. Permitted values for the base include ether-begin, mac-dst-
<base> begin, mac-srcbegin, ethTypeLen-begin, arp-begin, ip-hdr-begin, ip-options-begin, ip-
payload-begin, ip-tos-begin, ip-proto-begin, ip-src-begin, ip-dst-begin, ipv6-hdr-begin,
tcp-begin, tcp-srcport-begin, tcp-dstport-begin, tcp-flags-end, udp-begin, udp-srcport-
begin, udp-dstport-begin, ether-end, ip-hdr-end, icmp-msg-begin, tcp-end, or udp-end.
<WORD 0- Names the pattern with a new name that you define. Each of the three patterns must
32> have a unique name.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:filter apply act
Syntax
filter apply act <act-id>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
apply Applies or commits the ACT. After you issue the apply command, to change the ACT, you
must delete it ( if no ACLs are associated with it) and recreate it.
<1-4096> Specifies the ACT ID in the range of 1 to 4096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:flap-dampening
flap-dampening
Enables route suppression for routes that flap on and off.
Syntax
flap-dampening enable
Default
The default value is enable.
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables BGP flap-dampening.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:flow-control
flow-control
Configure the flow control pause0 and pause timer on the module.
Syntax
flowcontrol pause0
Default
The default is enable.
Command mode
Global configuration mode
Command parameters
Parameter Description
When tx-flow-control is enabled and flowcontrol pause0 is enabled, the TX port
pause0 transmits MAC control PAUSE frames with a timer value of 0 to indicate to its link
partner to resume transmission. This parameter only applies to 1 and 10 Gigabit
Ethernet ports.
Setting the pause time sets the timer value in the MAC control PAUSE frame. This
pause-time indicates to the link partner how long to pause transmission. The pause time is in
<0...65535> units of 512 bit-times. The default is 65535. This parameter only applies to 1 and 10
Gigabit Ethernet ports.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:format-flash
format-flash
Format the flash memory to ensure that you have adequate space to copy files.
Syntax
format-flash
Default
Command mode
Privileged EXEC mode
fpga update
For proper operation, review and, if required, update the field programmable gate array (FPGA) firmware revisions on every R
module.
Syntax
fpga update <1-4,7-10> foq [WORD <1-40>]
Default
Command mode
Global configuration mode
Command parameters
Parameter Description
<WORD 1-40> <WORD 1-40> specifies the FPGA image file name.
<1-4,7-10> Specifies the R module slot number. Slots 5 and 6 are for SF/CPUs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:fpga update bmc
Syntax
fpga update <1-4,7-10> bmc [WORD <1-40>]
Default
Command mode
Global configuration mode
Command parameters
Parameter Description
<WORD 1-40> <WORD 1-40> specifies the FPGA image file name.
<1-4,7-10> Specifies the R module slot number. Slots 5 and 6 are for SF/CPUs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:fpga update dpc
Syntax
fpga update <1-4,7-10> dpc [WORD <1-40>]
Default
Command mode
Global configuration mode
Command parameters
Parameter Description
<WORD 1-40> <WORD 1-40> specifies the FPGA image file name.
<1-4,7-10> Specifies the R module slot number. Slots 5 and 6 are for SF/CPUs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:fpga update pim
Syntax
fpga update <1-4,7-10> pim [WORD <1-40>]
Default
Command mode
Global configuration mode
Command parameters
Parameter Description
<WORD 1-40> <WORD 1-40> specifies the FPGA image file name.
<1-4,7-10> Specifies the R module slot number. Slots 5 and 6 are for SF/CPUs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:fpga update rs-module-dpm
Syntax
fpga update <1-4,7-10> rs-module-dpm [<WORD 1-40>]
Default
Command mode
Global configuration mode
Command parameters
Parameter Description
<WORD 1-40> <WORD 1-40> specifies the FPGA image file name.
<1-4,7-10> Specifies the RS module slot number. Slots 5 and 6 are for SF/CPUs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:fpga update rs pim
Syntax
fpga update <1-4,7-10> pim [WORD <1-40>]
Default
Command mode
Global configuration mode
Command parameters
Parameter Description
<WORD 1-40> <WORD 1-40> specifies the FPGA image file name.
<1-4,7-10> Specifies the RS module slot number. Slots 5 and 6 are for SF/CPUs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:framing sonet
framing sonet
Configure the framing type after the WAN mode is enabled.
Syntax
framing <sonet|sdh>
Default
The default value is SONET.
Command mode
Global configuration mode
Command parameters
Parameter Description
<sonet|sdh> Sets the port to SONET or SDH framing. This parameter only applies to 10 Gbit/s
WAN ports.
port
[portlist] Specifies the slot and the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:global-debug
global-debug
Displays specified debug information for BGP Global configuration modes.
Syntax
Default
The default value is none.
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies a list of mask choices separated by commas with no space between choices.
Mask choices are none disables all debug messages. all enables all debug messages. error
enables display of debug error messages. packet enables display of debug packet
messages. event enables display of debug event messages. trace enables display of
mask
<WORD 1- debug trace messages. warning enables display of debug warning messages. state
100> enables display of debug state transition messages. init enables display of debug
initialization messages. filter enables display of debug messages related to filtering.
update enables display of debug messages related to sending and receiving updates. The
no form of this command is no global-debug mask. The default form of this command is
default global-debug mask.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:global-debug mask
global-debug mask
Display specific debug messages for your global BGP configuration.
Syntax
global-debug mask <WORD 1-100>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
mask Specifies one or more mask choices that you enter, separated by commas with no space
<WORD 1- between choices. For example, [<mask>,<mask>,<mask>...]. Options include: none, all,
100> error, packet, event, trace, warning, state, init, filter, update.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:high-secure enable
high-secure enable
Protect the Avaya Ethernet Routing Switch 8800/8600 against IP packets with illegal IP addresses such as loopback addresses or a
source IP address of ones, or Class D or Class E addresses from being routed.
Syntax
high-secure enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Enables the high secure feature that blocks packets with illegal IP addresses. This flag is
enable disabled by default. Use the no operator to remove this configuration. To set this option
to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:host-route
host-route
Use host routes when the Ethernet Routing Switch 8800/8600 resides in a network that uses routing protocols other than OSPF.
Syntax
host-route <A.B.C.D> [metric <0-65535>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<A.B.C.D> Specifies the IP address of the host router in a.b.c.d format.
metric <0-65535> Configures the metric (cost) for the host route.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ibgp-report-import-rt
ibgp-report-import-rt
Configures BGP to advertise imported routes to an interior BGP (IBGP) peer. This command also enables or disables advertisement
of nonBGP imported routes to other IBGP neighbors.
Syntax
ibgp-report-import-rt enable
Default
The default value is enable.
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables advertisement of nonBGP imported routes to other IBGP neighbors.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ignore-illegal-rtrid
ignore-illegal-rtrid
Overlook an illegal router id after enabling BGP.
Syntax
ignore-illegal-rtrid enable
Default
The default value is enable.
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enable or disable the acceptance of a connection from a peer that sends an open
message using a router ID of 0 (zero).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:install
install
Configure the switch with the setup utility to monitor system requirements and obtain the maximum system performance.
Syntax
install
Default
None
Command mode
Privileged EXEC mode
interface-ip
Specifies the CLIP interface that the WSP is using for a system IP address.
Syntax
interface-ip <A.B.C.D>
Default
None
Command mode
WLAN Switch Configuration
Command parameters
Parameter Description
<A.B.C.D> Specifies the CLIP interface that the WSP is using for a system IP address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip access-list extended
ip access-list extended
Create an extended ACL with a prefix entry.
Syntax
ip access-list extended Word<1-64> <A.B.C.D> <A.B.C.D> <A.B.C.D> <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Word <164> Specifies the name, up to 255 characters, for the extended
ACL.
<A.B.C.D> <A.B.C.D> <A.B.C.D> Specifies the IP address and mask for the source, and then
<A.B.C.D> the destination.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip address
ip address
Configure a circuitless IP interface (CLIP) when you want toprovide a virtual interface that is not associated with a physical port.
Youcan use a CLIP interface to provide uninterrupted connectivity to yourswitch. You can configure a maximum of 256 CLIP
interfaces on each device.
Syntax
ip address <A.B.C.D> <A.B.C.D> [<0-65535>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
address [<1- Specifies the IP address for the CLIP interface.<1-256> specifies the interface ID
256>] value; <A.B.C.D/X> specifies the IP address and mask; vrf <WORD 0-32>
<A.B.C.D/X> specifies an associated VRF by name in the range of 0 to 32 characters. The no
[vrf <WORD 0- form of this command is no ip address [<1-256>] <A.B.C.D> [vrf <WORD 0-
32>] 32>].
<vid> Specifies the VLAN id. The range is between 1 and 4094. The default value is 1.
ipaddr/Network Indicates the IP address in the format {a.b.c.d} and the subnet mask assigned to
mask the VLAN.
mac_offset Indicates the Media Access Control (MAC) address you want to assign to this
value VLAN. This is an optional parameter, which, if used, replaces the default MAC
address and ranges from 0 to 65 535.
<ipaddr>
<mask> Adds IP address and network mask to VLAN.
[ <0-65535> ] Specifies the Mac-offset value. The value is in the range of 0 to 65535.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip alternative-route
ip alternative-route
Enable the Alternative Route feature globally.
Syntax
ip alternative-route
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Enables or disables the Alternative Route feature. The default value is enabled. If
the alternative-route parameter is disabled, all existing alternative routes are
alternative-
route removed. When the parameter is enabled, all alternative routes are re-added. The
default form of this command is default ip alternative-route. The no form of this
command is no ip alternative-route.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip apply redistribute isis
Syntax
ip {bgp | ospf | rip} apply redistribute isis [vrf <WORD 0-64>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
{bgp | ospf | rip} Specifies the type of routes to be redistributed (the protocol source).
[vrf <WORD 064>] Specifies the VRF instance.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip arp
ip arp
Configure ARP static entries to modify the ARP parameters on theswitch. The only way to change a static ARP is to delete the
static ARPentry and create a new entry with new information.
Syntax
ip arp static-mcast
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
static-mcast Configures static multicast MAC entries.
<A.B.C.D> Adds ARP entries.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip arp inspection
ip arp inspection
This command configures port ARP status to specify whether a port or range of ports is trusted or untrusted.
Syntax
ip arp inspection [port <portlist>]
Default
None
Command mode
Interface configuration mode
Command parameters
Parameter Description
<portlist> Specifies a single port or range of ports, entered as [slot/port [-slot/port][,...]}.
<trusted> Specifies that ARP traffic is not subject to Dynamic ARP inspection.
<untrusted> Specifies that ARP traffic is subject to Dynamic ARP inspection.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip arp inspection vlan
Syntax
[no] ip arp inspection vlan <vid>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<vid> An integer that identifies a VLAN. Values range from 14094.
no Disables Dynamic ARP inspection to stop applying ARP validation security on a specific
VLAN or all VLANs configured on the swtich.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip arp-proxy enable
ip arp-proxy enable
Configure an ARP proxy to allow a router to answer a local ARPrequest for a remote destination.
Syntax
ip arp-proxy enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the proxy Address Resolution Protocol.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip arp-response
ip arp-response
Enable Address Resolution Protocol (ARP) on the switch to allow arouter to answer a local ARP request.
Syntax
ip arp-response
Default
None
Command mode
Global configuration mode
ip arp static-mcast
Configure Layer 3 multicast MAC filtering to route an IP frame to a unicast IP address and flood it with a destination multicast
MAC address.
Syntax
ip arp static-mcast <A.B.C.D> <MAC address> vid <1-4094> [port <value> Word<1-16>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<MAC
address> Specifies the MAC address in hexadecimal format.
A.B.C.D Specifies the IP address.
vid <1
4094> Specifies the VLAN ID.
port Specifies the port that receives the multicast flooding. Type this information as a port or
<value> a range of ports in slot/port format.
<116> Specifies the multilink trunk ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip as-list
ip as-list
Use an AS path list to restrict the routing information a router learns or advertises to and from a neighbor. The AS path list acts as
a filter that matches AS paths.
Syntax
ip as-list <1-1024> memberId <0-65535> <permit|deny> as-path <WORD 0-1536>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
as-list <1-
1024> Creates the specified AS-path list entry.
memberId <0- Adds a regular expression entry to the specified AS-path list. It is an integer value
65535> between 0 and 65535.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip bfd brouter port
Syntax
ip bfd [vlan <1-4094>] enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables BFD on the interface. The no and default versions of this command disable BFD
on the interface.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip bfd vlan enable
Syntax
ip bfd [vlan <1-4094>] enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables BFD on the VLAN. The no and default versions of this command disable BFD on
the VLAN.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip bgp enable
ip bgp enable
Configure the external Border Gateway Protocol (eBGP) for the VRF to exchange BGP routes between a PE node and a CE device.
Syntax
ip bgp enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the BGP on the VRF.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip bgp in-route-policy
ip bgp in-route-policy
Configure peer level policies to apply a route policy rule to all routes that are learned from, or sent to, the local BGP router peers
or peer groups.
Syntax
ip bgp in-route-policy <WORD>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
in-
route- Configures the incoming policy.
policy
Specifies a route-map name. This option is a string value from 1256 characters. Use the
Word no operator to later remove this configuration. To configure this option to the default
value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip bgp multiple-paths
ip bgp multiple-paths
Configure Border Gateway Protocol (BGP) inbound route filtering on the global routing engine (GRE) to reduce BGP update
messaging after you configure new VPNs (that is, new route targets) on the node.
Syntax
ip bgp multiple-paths <1-8>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Configures the maximum number of equal multicost routes to store in the routing table.
18 The range is 18. To configure this option to the default value, use the default operator
with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip bgp neighbor
ip bgp neighbor
Add a BGP peer group to the VRF.
Syntax
ip bgp neighbor <nbr_ipaddr|peer-group-name> peer-group <WORD>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the properties of a statically configured peer within a BGP group.
<nbr_ipaddr|peer-
group-name> Enter the neighbor IP address in a.b.c.d format for <nbr_ipaddr>, or the
neighbor group name for <peer-group-name>.
WORD Specifies the name of the peer group to add to the VRF. Use the no operator
to later remove this configuration.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip bgp neighbor allow-as-in
Syntax
ip bgp neighbor <nbr_ipaddr|peer-group-name> allow-as-in <0-10>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Configures the number of times the local ASN can exist in the AS-PATH of a
<010> received route. To configure this option to the default value, use the default
operator with the command.
Specifies the properties of a statically configured peer within a BGP group.
<nbr_ipaddr|peer-
group-name> Enter the neighbor IP address in a.b.c.d format for <nbr_ipaddr>, or the
neighbor group name for <peer-group-name>.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip bgp neighbor as-override
Syntax
ip bgp neighbor <nbr_ipaddr|peer-group-name> as-override
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the properties of a statically configured peer within a BGP group.
<nbr_ipaddr|peer-
group-name> Enter the neighbor IP address in a.b.c.d format for <nbr_ipaddr>, or the
neighbor group name for <peer-group-name>.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip bgp neighbor remove-
private-as
Syntax
ip bgp neighbor <nbr_ipaddr|peer-group-name> remove-private-as enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the properties of a statically configured peer within a BGP group.
<nbr_ipaddr|peer-
group-name> Enter the neighbor IP address in a.b.c.d format for <nbr_ipaddr>, or the
neighbor group name for <peer-group-name>.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip bgp neighbor site-of-
origin
Syntax
ip bgp neighbor <nbr_ipaddr|peer-group-name> site-of-origin <WORD>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the site of origin in one of two formats:AS number:assigned number
in the ranges 065535:04294967295 IPv4 address:assigned number as
WORD A.B.C.D:065535 Use the no operator to later remove this configuration. To
configure this option to the default value, use the default operator with the
command.
Specifies the properties of a statically configured peer within a BGP group.
<nbr_ipaddr|peer-
group-name> Enter the neighbor IP address in a.b.c.d format for <nbr_ipaddr>, or the
neighbor group name for <peer-group-name>.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip [bgp|ospf|rip] apply
redistribute
Syntax
ip [bgp][ospf][rip] apply redistribute
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[bgp] Specifies BGP as the type of route to be redistributed (the protocol source).
[ospf] Specifies OSPF as the type of route to be redistributed (the protocol source).
[rip] Specifies RIP as the type of route to be redistributed (the protocol source).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip bgp redistribute isis
route-map
Syntax
ip bgp redistribute isis route-map <WORD 0-64>
Default
None
Command mode
VRF router configuration mode
Command parameters
Parameter Description
<WORD 064> Specifies the policy name. Type a name between 064 characters in length.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip community-list
ip community-list
Use community lists to specify permitted routes by using their BGP community. This list acts as a filter that matches communities
or AS numbers
Syntax
ip community-list <1-1024> memberId <0-65535> <permit|deny> community-string <WORD 0-256>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
community-
list <1- Creates the specified community list entry.<1-1024> specifies the list id.
1024>
memberId <0- Adds an entry to the community list. <0-65535> is an integer value between 0 and
65535> 65535 that represents the member ID in the community list.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dhcp-relay
ip dhcp-relay
View and configure DHCP parameters globally on the Ethernet RoutingSwitch 8800/8600.
Syntax
ip dhcp-relay
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
dhcp-relay Configures the Dynamic Host Control Protocol (DHCP) parameters on the switch.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dhcp-relay broadcast
ip dhcp-relay broadcast
You can view and configure DHCP parameters on specific ports or ona VLAN.
Syntax
ip dhcp-relay broadcast
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
When enabled, sends the server reply as a broadcast to the end station. When disabled,
broadcast sends the server reply as a unicast to the end station. Use the no operator to disable
broadcast: no ip dhcp-relay broadcast To set this option to the default value, use the
default operator with this command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dhcp-relay fwd-path
ip dhcp-relay fwd-path
Create the forwarding path from the client to the server.
Syntax
ip dhcp-relay fwd-path <A.B.C.D> <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Configures the forwarding path from the client to the server. A.B.C.D is the IP address
configured on an interface (a locally configured IP address) to forward or relay BootP or
fwd-path DHCP. A.B.C.D is the IP address of the DHCP server in the network. If this IP address
<A.B.C.D>
<A.B.C.D> corresponds to the locally configured IP network, the DHCP packet is broadcast out from
the interface. Use the no operator to delete the forwarding path from the client to the
server: no ip dhcp-relay fwd-path <A.B.C.D> <A.B.C.D>
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dhcp-relay fwd-path
enable
Syntax
ip dhcp-relay fwd-path <A.B.C.D> <A.B.C.D> enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
fwd-path Enables DHCP relaying on the path from the IP address to the server. A.B.C.D is the IP
<A.B.C.D> address configured on an interface (a locally configured IP address). A.B.C.D is the IP
<A.B.C.D> address of the DHCP server in the network. If this IP address corresponds to the locally
enable configured IP network, the DHCP packet is broadcast out from the interface.
disable Disables DHCP relaying on the path from the IP address to the server.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dhcp-relay fwd-path
mode
Syntax
ip dhcp-relay fwd-path <A.B.C.D> <A.B.C.D> mode <bootp|bootp-dhcp|dhcp>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
fwd-path <A.B.C.D> Modifies DHCP mode to forward BootP messages only, DHCP
<A.B.C.D> mode messages only, or both. The default is both. mode is {bootp |
<bootp|bootp-dhcp|dhcp> bootp_dhcp | dhcp}.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dhcp snooping
ip dhcp snooping
Configure port-based DHCP snooping to specify whether a port or range of ports is configured as trusted or untrusted.
Syntax
ip dhcp snooping [port<portlist>]<trusted|untrusted>
Default
The default value is untrusted.
Command mode
Interface configuration mode
Command parameters
Parameter Description
<portlist> Specifies a single port or range of ports, entered as {slot/port [-slot/port][,...]}.
<trusted> Specifies that the DHCP snooping state for a port or ports is configured as trusted.
<untrusted> Specifies that the DHCP snooping state for a port or ports is configured as untrusted.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dhcp snooping binding
interface
Syntax
[no] ip dhcp snooping binding <mac> vlan <vid> ip <ip> interface <slot/port>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<mac> Specifies the MAC address for the static binding entry.
vlan <vid> Specifies the VLAN to associate with the static binding entry.
ip <ip> Specifies the IP address for the static binding entry.
interface <slot/port> Specifies the port to associate with the static binding entry.
no Use this command to delete a static DHCP snooping binding entry.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dhcp snooping enable
Syntax
[no] ip dhcp snooping
Default
The default value is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
no Disables the specified global DHCP snooping feature.
default Disables the specified global DHCP snooping feature.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dhcp snooping vlan
enable
Syntax
[no] [default] ip dhcp snooping vlan <vid> [enable]
Default
The default value is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
<vid> An integer that identifies a VLAN. Values range from 14094
no Disables VLAN-based DHCP snooping.
default Disables VLAN-based DHCP snooping.
enable Enables VLAN-based DHCP snooping.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip directed-broadcast enable
ip directed-broadcast enable
Configure the device to forward directed broadcasts for a VLAN.
Syntax
ip directed-broadcast enable
Default
The default is enabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Allows the device to forward directed broadcast frames to the specified VLAN. The default
setting for this feature is enabled.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip domain-name
ip domain-name
Configure the Domain Name Service to establish the mapping between an IP name and an IP address.
Syntax
ip domain-name <word>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
domain-name <word> Configures the default domain name. word is a string 0255 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dvmrp
ip dvmrp
Configure the Distance Vector Multicast Routing Protocol (DVMRP) globally to enable or disable DVMRP and change default global
parameters.
Syntax
ip dvmrp
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
fwd-cache- Configures the forward cache timeout (in seconds). integer is the range of 1086400
timeout seconds. The default value is 300 seconds. To set this option to the default value, use
<integer> the default operator with the command.
Enables or disables the DVMRP log. Use the no operator to later remove this
generate-
log configuration. To set this option to the default value, use the default operator with
the command. The default is disabled.
Enables or disables the DVMRP trap. Use the no operator to later remove this
generate-
trap configuration. To set this option to the default value, use the default operator with
the command. The default is disabled.
Configures the length of time (in seconds) the router waits for a response from a
leaf- neighbor before considering the attached network as a leaf network. integer is the
timeout
<integer> range of 254000 seconds. The default value is 125 seconds. To set this option to the
default value, use the default operator with the command.
Configures the time interval (in seconds) for the DVMRP router to send a neighbor
nbr-probe- probe message on its interface. integer is the range of 530 seconds. The default
interval
<integer> value is 10 seconds. To set this option to the default value, use the default operator
with the command.
Configures the length of time (in seconds) the router waits to receive a report from a
nbr-timeout neighbor before considering the connection inactive. integer is the range of 358000
<integer> seconds. The default value is 35 seconds. To set this option to the default value, use
the default operator with the command.
output- Configures the time interval (in seconds) between DVMRP router update messages.
report- integer is the range of 102000 seconds. The default value is 60 seconds. To set this
delay
<integer> option to the default value, use the default operator with the command.
Sends prune messages every 3 minutes, to address the link failures at remote
prune- upstream switches. The feature is disabled by default. Use the no operator to later
resend remove this configuration. To set this option to the default value, use the default
operator with the command.
route- Configures the route discard timeout (in seconds). integer is the range of 258000.
discard- The default value is 260 seconds. To set this option to the default value, use the
timeout
<integer> default operator with the command.
route- Configures the route expiration timeout (in seconds). integer is the range of 204000
expiration- seconds. The default value is 140 seconds. To set this option to the default value, use
timeout
<integer> the default operator with the command.
route- Configures the route switch timeout (in seconds). integer is the range of 202000.
switch- The default value is 140 seconds. To set this option to the default value, use the
timeout
<integer> default operator with the command.
Enables or disables showing information about the DVMRP next hops. Use the no
show-next-
hop-table operator to later remove this configuration. To set this option to the default value,
use the default operator with the command. The default is disabled.
triggered- Configures the time interval (in seconds) between triggered update messages sent
update- after routing information changes. integer is the range of 51000 seconds. The
interval default value is 5 seconds. To set this option to the default value, use the default
<integer> operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dvmrp active
ip dvmrp active
Create an active port to receive all types of incoming DVMRP packets from neighbors, and send out probes or route reports to
neighbor switches.
Syntax
ip dvmrp active
Default
None
Command mode
Global configuration mode
Syntax
ip dvmrp advertise-self port
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Advertises the local network if the setting is enable. Use the no operator to later
advertise-
self remove this configuration. To set this option to the default value, use the default
operator with the command. The default is enabled.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dvmrp advertise-self vlan
Syntax
ip dvmrp advertise-self vlan
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Advertises the local network if the setting is enable. Use the no operator to later
advertise-
self remove this configuration. To set this option to the default value, use the default
operator with the command. The default is enabled.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dvmrp default-listen
ethernet port
Syntax
ip dvmrp default-listen ethernet port
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Learns the default route over the specified interface if this feature is enabled on the
default- interface. The default setting is enable. Use the no operator to later remove this
listen configuration. To set this option to the default value, use the default operator with the
command. The default is to listen.
Generates and advertises the default route if this feature is enabled on the interface. The
default- default setting is disable. Use the no operator to later remove this configuration. To set
supply this option to the default value, use the default operator with the command. The default
is to not supply.
default- Advertises the specified metric over the interface if you configured the interface to supply
supply- the default route. The range is 131 hops. The default setting is 1 hop. To set this option
metric
<cost> to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dvmrp default-listen vlan
Syntax
ip dvmrp default-listen vlan
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Learns the default route over the specified interface if this feature is enabled on the
default- interface. The default setting is enable. Use the no operator to later remove this
listen configuration. To set this option to the default value, use the default operator with the
command. The default is to listen.
Generates and advertises the default route if this feature is enabled on the interface. The
default- default setting is disable. Use the no operator to later remove this configuration. To set
supply this option to the default value, use the default operator with the command. The default
is to not supply.
default- Advertises the specified metric over the interface if you configured the interface to supply
supply- the default route. The range is 131 hops. The default setting is 1 hop. To set this option
metric
<cost> to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dvmrp enable ethernet
port
Syntax
ip dvmrp enable ethernet port
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables DVMRP on the local router interface. To set this option to the default value, use
the default operator with the command. The default is disabled.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dvmrp enable vlan
Syntax
ip dvmrp enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables DVMRP on the local router interface. To set this option to the default value, use
the default operator with the command. The default is disabled.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dvmrp in-policy ethernet
port
Syntax
ip dvmrp in-policy ethernet port
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the DVMRP route in-policy. policy_name is a policy name that uses a
in-policy
<policy_name> string length of 064. To set this option to the default value, use the default
operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dvmrp in-policy vlan
Syntax
ip dvmrp in-policy vlan
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the DVMRP route in-policy. policy_name is a policy name that uses a
in-policy
<policy_name> string length of 064. To set this option to the default value, use the default
operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dvmrp interface-type
active
Syntax
ip dvmrp interface-type active [port|vlan]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
vlan Specifies the VLAN to configure.
port Specifies which port to configure.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip dvmrp out-policy
ip dvmrp out-policy
Apply a DVMRP announce policy to a port to control which routes the switch sends to neighboring routers, to reduce the size of
routing tables, or to provide a level of security for the network.
Syntax
Default
None
Command mode
Global configuration mode
ip dvmrp show-next-hop-table
Enable showing the next-hop table on the switch.
Syntax
ip dvmrp show-next-hop-table
Default
None
Command mode
Global configuration mode
ip ecmp
Enable Equal cost multiplepath protocol (ECMP).
Syntax
ip ecmp
Default
The default is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
Enables or disables ECMP. If the ECMP parameter is disabled, all existing ECMP routes are
ecmp removed. When ECMP is enabled, all ECMP routes are re-added. The no form of this
command is no ip icmp.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ecmp max-path
ip ecmp max-path
Configure the number of equal cost multi path (ECMP) routes that the VRF can learn from remote PE routers and route reflectors
to allow the system to distribute IP VPN traffic across multiple paths.
Syntax
ip ecmp max-path <1-8>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Configures the maximum number of ECMP routes that can be stored in the routing table.
18 The range is 18. To configure this option to the default value, use the default operator
with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip extcommunity-list
ip extcommunity-list
Configure policies using extended communities to include one or more communities in the policy.
Syntax
ip extcommunity-list <1-1024> memberId <0-65535> rt <0-65536> <0-2147483647> [soo {<0-
65535> <0-2147483647>|<A.B.C.D> <0-65535>}]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
memberId <0- Specifies an integer value between 0 and 65535 that represents the member ID
65535> in the community list.
rt <0-65536> Specifies the route target in the format {AS number:assigned number} (that is,
<0-2147483647> {0 to 65535}:{0 to 2147483647}) or {ipaddress:assigned number} (that is,
rt <A.B.C.D>
<0-65535> {a.b.c.d}:{0 to 65535}).
11024 Assigns an ID to the list from 11024.
memberId <1
65535> Defines each member by specifying one or more member ID values.
Specifies a route target. <WORD> is <AS number> <assigned number> or
rt <WORD> <ipaddress> <assigned number>. If you use the AS number, the assigned
number is in the range 02147483647. If you use the IP address, the assigned
number is in the range 065535.
Specifies a site of origin. <WORD> is <AS number> <assigned number> or
soo <WORD> <ipaddress> <assigned number>. If you use the AS number, the assigned
number is in the range 02147483647. If you use the IP address, the assigned
number is in the range 065535.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip forward-protocol udp
ip forward-protocol udp
Configure UDP protocols to determine which UDP broadcasts are forwarded
Syntax
ip forward-protocol udp
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-65535> <WORD Creates a new UDP protocol. <1-65535> <WORD 1-15> is the UDP protocol
1-15> name as a string.
[vrf <WORD 0-
32>] The name of the VRF.
[vrfids <0-255>] The ID of the VRF. The value is an integer between 0 and 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip forward-protocol udp
broadcastmask
Syntax
ip forward-protocol udp broadcastmask <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<A.B.C.D> Sets the interface broadcast mask (the interface broadcast mask can be different from
the interface mask). A.B.C.D is an IP address in a.b.c.d format.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip forward-protocol udp
maxttl
Syntax
ip forward-protocol udp maxttl <1-16>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
maxttl Sets the maximum time-to-live value (TTL) for the UDP broadcast forwarded by the
<1-16> interface. The range is 1 to 16.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip forward-protocol udp
portfwd
Syntax
ip forward-protocol udp portfwd
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Adds a UDP protocol port to the specified port forwarding list. 1-65535 is a UDP protocol
<1- port in the range of 1 to 65535. A.B.C.D is an IP address in a.b.c.d format. Use the no
65535> operator to remove a protocol port forwarding entry and IP address from the list: no ip
<A.B.C.D> forward-protocol udp portfwd <1-65535> <A.B.C.D> To set this option to the default
value, use the default operator with this command.
[vrf
<WORD 0- The name of the VRF.
32>]
[vrfids
<0-255>] The ID of VRF and is an integer between 0 and 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip forward-protocol udp
portfwdlist
Syntax
ip forward-protocol udp portfwdlist <1-1000>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-1000> Creates a UDP port forwarding list in the range of 1 to 1000.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip icmp redirect
ip icmp redirect
Enables ICMP redirect and unreachable messages.
Syntax
ip icmp redirect
Default
None
Command mode
Global configuration mode
Syntax
ip igmp access-list <word> <host IP address>/<host mask address> <deny-tx|deny-rx|deny-
both|allow-only-tx|allow-only-rx|allow-only-both>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Creates an access control group entry for a specific IGMP interface. host IP
<host IP address is the IP address of the host. host mask address is the subnet mask
address> <host used to determine the host or hosts covered by this configuration. You can
mask address> use the host subnet mask to restrict access to a portion of the network for the
host.
deny-tx|deny-
rx|deny-
both|allow-only- Indicates the action for the specified IGMP interface. For example, if you
tx|allow-only- specify deny-both, the interface denies both transmitted and received traffic.
rx|allow-only-
both
word Specifies the name of the access list from 164 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp access-list mode
Syntax
ip igmp access-list <word> <host IP address>/<host mask address> mode <deny-tx|deny-
rx|deny-both|allow-only-tx|allow-only-rx|allow-only-both
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Creates an access control group entry for a specific IGMP interface. host IP
<host IP address is the IP address of the host. host mask address is the subnet mask
address> <host used to determine the host or hosts covered by this configuration. You can
mask address> use the host subnet mask to restrict access to a portion of the network for the
host.
deny-tx|deny-
rx|deny-
both|allow-only- Indicates the action for the specified IGMP interface. For example, if you
tx|allow-only- specify deny-both, the interface denies both transmitted and received traffic.
rx|allow-only-
both
mode Changes the access control group configuration.
word Specifies the name of the access list from 164 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp access-list mode
vlan
Syntax
ip igmp access-list <word> <host IP address>/<host mask address> mode <deny-tx|deny-
rx|deny-both|allow-only-tx|allow-only-rx|allow-only-both
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Creates an access control group entry for a specific IGMP interface. host IP
<host IP address is the IP address of the host. host mask address is the subnet mask
address> <host used to determine the host or hosts covered by this configuration. You can
mask address> use the host subnet mask to restrict access to a portion of the network for the
host.
deny-tx|deny-
rx|deny-
both|allow-only- Indicates the action for the specified IGMP interface. For example, if you
tx|allow-only- specify deny-both, the interface denies both transmitted and received traffic.
rx|allow-only-
both
mode Changes the access control group configuration.
word Specifies the name of the access list from 164 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp access-list vlan
Syntax
ip igmp access-list <word> <host IP address>/<host mask address> <deny-tx|deny-rx|deny-
both|allow-only-tx|allow-only-rx|allow-only-both>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Creates an access control group entry for a specific IGMP interface. host IP
<host IP address is the IP address of the host. host mask address is the subnet mask
address> <host used to determine the host or hosts covered by this configuration. You can
mask address> use the host subnet mask to restrict access to a portion of the network for the
host.
deny-tx|deny-
rx|deny-
both|allow-only- Indicates the action for the specified IGMP interface. For example, if you
tx|allow-only- specify deny-both, the interface denies both transmitted and received traffic.
rx|allow-only-
both
word Specifies the name of the access list from 164 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp ethernet port
Syntax
ip igmp
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
access-list Displays the IP Multicast access group list parameters.
Enables v2-v3 compatibility mode. The default value is disabled, which means
compatibility- IGMPv3 is not compatible with IGMPv2. To use the default configuration, use
mode the default option in the command: default ip igmp compatibility-mode, or use
the no option to disable compatibility mode: no ip igmp compatibility-mode
Configures if the Avaya Ethernet Routing Switch 8800/8600 downgrades the
version of IGMP to handle older query messages. If the switch downgrades,
the host with IGMPv3 only capability does not work. If you do not configure
dynamic- the switch to downgrade the version of IGMP, the switch logs a warning. The
downgrade-
version switch downgrades to the oldest version of IGMP on the network by default.
To use the default configuration, use the default option in the command:
default ip igmp dynamic-downgrade-version, or use the no option to disable
downgrade: no ip igmp dynamic-downgrade-version
Enables the fast leave option on the interface. Use the no operator to later
immediate-leave remove this configuration. To set this option to the default value, use the
default operator with the command. The default is disabled.
Configures the maximum response time (in tenths of a second) that is
inserted into group-specific queries sent in response to leave group messages.
This value is also the time between group-specific query messages. This value
last-member- is not configurable for IGMPv1. Decreasing the value reduces the time to
query-interval detect the loss of the last member of a group. 1/10_seconds is an integer in
<1/10_seconds> the range from 0255 and the default is 10 tenths of a second. Avaya
recommends that you configure this value between 310 (equal to 0.31.0
seconds). To set this option to the default value, use the default operator with
the command.
port
{slot/port[- Configures IGMP for a specific port.
slot/port][,...]}
Configures the frequency (in seconds) at which the interface transmits host
query-interval query packets. seconds is an integer in the range from 065535 with a default
<seconds> of 125. To set this option to the default value, use the default operator with
the command.
Configures the maximum response time (in tenths of a second) advertised in
IGMPv2 general queries on this interface. This value is not configurable for
query-max- IGMPv1. Smaller values allow a router to prune groups faster. 1/10_seconds
response is an integer value with a range of 0255, and the default is 100 tenths of a
<1/10_seconds> second (equal to 10 seconds). Important You must configure this value lower
than the query-interval. To set this option to the default value, use the default
operator with the command.
Configures the expected packet loss of a network. integer is an integer value
robust-value with a range of 2255 seconds. The default value is 2 seconds. Increase the
<integer> value if you expect the network to experience packet loss. To set this option
to the default value, use the default operator with the command.
When enabled, this parameter instructs the router to ignore IGMP packets
that do not contain the router alert IP option. When disabled (default setting),
the router processes IGMP packets regardless of whether the router alert IP
router-alert option is set. Important To maximize your network performance, Avaya
recommends that you set this parameter according to the version of IGMP
currently in use: IGMPv1-Disable IGMPv2-Enable IGMPv3-Enable Use the no
operator to later remove this configuration. To set this option to the default
value, use the default operator with the command.
stream-limit Enables the stream-limit feature.
stream-limit-
max-streams Sets the maximum number of streams allowed on an interface.
Configures the version of IGMP that you want to configure on this interface.
version For IGMP to function correctly, all routers on a LAN must use the same
<integer> version. integer is an integer value with a value of 1, 2, or 3. The default
value is 2 (IGMPv2).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp generate-log
ip igmp generate-log
Configure the Ip IGMP commands to manage the performance of the network.
Syntax
ip igmp generate-log
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
generate-log Sets IGMP log.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp igap
ip igmp igap
Configure IGAP on an interface or a VLAN to authenticate and account the user for the clients receiving multicast streams on their
networks.
Syntax
ip igmp igap authentication
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
authentication Enables authentication on the IGAP interface. The default is enable.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp immediate-leave
ip igmp immediate-leave
Configure IGMP fast leave members on a port or VLAN to specify fast leave capable ports.
Syntax
ip igmp immediate-leave
Default
None
Command mode
Global configuration mode
ip igmp immediate-leave-members
Configure fast leave members on a VLAN to specify fast leave capable ports.
Syntax
ip igmp immediate-leave-members <ports>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<ports> Specifies the port or list of ports that you want to join the fast leave group.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp immediate-leave-
mode
ip igmp immediate-leave-mode
Configure fast (immediate) leave mode to specify if a port receives a leave message from a member of a group.
Syntax
ip igmp immediate-leave-mode <multiple-user|one-user>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
multiple-user removes from the group only the IGMP member who sent the leave
multiple- message. Traffic does not stop if other receivers exist on the interface port. This setting
user|one- is the default. one-user removes all group members on a fast leave enabled interface
user port after receiving the first leave message from a member. This behavior is the same as
the conventional fast leave process.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp mrdisc
ip igmp mrdisc
Configure the multicast route discovery options to enable the automatic discovery of multicast-capable routers.
Syntax
ip igmp mrdisc
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Configures the maximum number (in seconds) between successive
maxadvertinterval advertisements. For this change to take effect, you must save the
<seconds> configuration and reset the switch. To set this option to the default
value, use the default operator with the command. The default is 20.
Configures the maximum number (in seconds) between successive initial
maxinitadvertinterval advertisements. For this change to take effect, you must save the
<seconds> configuration and reset the switch. To set this option to the default
value, use the default operator with the command. The default is 2.
Configures the maximum number of initial multicast advertisements after
maxinitadvertisements initialization. For this change to take effect, you must save the
<integer> configuration and reset the switch. To set this option to the default
value, use the default operator with the command. The default is 3.
Configures the minimum number (in seconds) between successive
minadvertinterval advertisements. For this change to take effect, you must save the
<seconds> configuration and reset the switch. To set this option to the default
value, use the default operator with the command. The default is 15.
Configures the multicast router discovery dead interval-the number of
seconds the multicast route neighbors for the switch must wait before
neighdeadinterval
<seconds> assuming that the multicast router is down. seconds is a value from 1
59. The default is 60. To set this option to the default value, use the
default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp snoop-querier
ip igmp snoop-querier
Enables snoop querier.
Syntax
ip igmp snoop-querier
Default
The default is disable.
Command mode
VLAN Interface configuration code
ip igmp snoop-querier-addr
Specifies the snoop querier IP address on a VLAN interface in the {a.b.c.d} format.
Syntax
ip igmp snoop-querier-addr <A.B.C.D>
Default
None
Command mode
VLAN Interface configuration code
Syntax
ip igmp ssm group-range <A.B.C.D/X>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Defines the SSM range. The SSM range parameter extends the default SSM range of
232/8 to include an IP multicast address. You can configure existing applications without
A.B.C.D/X having to change their group configurations. This parameter specifies an IP multicast
address within the range of 224.0.1.0 and 239.255.255.255. The default is 232.0.0.0.
The address mask is the IP address mask of the multicast group. The default is
255.0.0.0.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp ssm-map
ip igmp ssm-map
Configure the SSM channel table to map groups to their sending source.
Syntax
[no] ip igmp ssm-map [all]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
no Use the no option to delete an IGMP static receiver. This command will delete all IGMP
static receivers for the selected group.
all Enables SSM channel for all the static entries.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp static-group
ip igmp static-group
Configure IGMP static members to add members to a snoop group.
Syntax
ip igmp static-group <group address> <to group address> [<portList>] <static|blocked>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Adds a static-member entry to the IGMP interface. value is the port or list of
<static|blocked> ports to which you want to redirect the multicast stream for this multicast
group. static|blocked configures the route to static or blocked.
Creates static members on the interface. Specifies the port or list of ports to
portList which you want to redirect the multicast stream for this multicast group. Use
the format {slot/port[-slot/port][,...]}. Use the no operator to later remove this
configuration.
<group address> Indicates the IP address range {a.b.c.d[-w.x.y.z]} of the selected multicast
<to group
address> group.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp stream-limit
ip igmp stream-limit
Configure multicast stream limitation on an Ethernet port to limit the number of concurrent multicast streams on the port.
Syntax
ip igmp stream-limit
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
stream-limit Enables the stream limit on the specifies Ethernet port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp stream-limit-group
ip igmp stream-limit-group
Configure multicast stream limitation members on ports of a specific VLAN to limit the number of multicast groups that can join a
VLAN.
Syntax
ip igmp stream-limit-group <ports> enable max-streams <value>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
max- Configures the maximum number of allowed streams for the specified ports on this VLAN.
streams The range is from 065535 and the default is 4. To use the default configuration, use the
<value> default option in the command: default ip igmp stream-limit-group <ports>
<ports> Specifies the port or port list in the format {slot/port[-slot/port][,...]}.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp stream-limit-max-
streams
ip igmp stream-limit-max-streams
Configure the maximum number of allowed streams on the port.
Syntax
ip igmp stream-limit-max-streams <0-65535>
Default
The default value is 4.
Command mode
Global configuration mode
Command parameters
Parameter Description
stream-limit-max- Sets the maximum number of streams allowed on an interface. The
streams <0-65535> value ranges from 0 to 65 535.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp stream-limit vlan
Syntax
ip igmp stream-limit vlan
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
stream-limit Enables the multicast stream limitation on a VLAN interface.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip igmp version
ip igmp version
Set the version of IGMP on each VLAN on the switch to enable IGAP configuration.
Syntax
ip igmp version
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<vid> Specifies the VLAN id. The range is between 1 and 4094. The default value is 1.
version Indicates the version of IGMP ranging from 1 to 3.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ipfix collector
ip ipfix collector
Configure up to two collectors for each slot.If you do not specify an Exporter IP address, the source IP address is chosen from
Virtual IP, Management IP, or outgoing interface IP based on the collector IP reachability.
Syntax
ip ipfix collector <slotList> <A.B.C.D> {[enable] [protocol {udp|tcp|sctp}] [dest-port <1-
65535, [exporter-ip <A.B.C.D>] [protocol-version {ipfix|preipfix|preipfixv5}]}
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<A.B.C.D> {[enable] Configures or modifies a collector. enable-state of collector
[protocol {udp|tcp|sctp}] {false|true}. <A.B.C.D>-IP address of collector. protocol-type
[dest-port <1-65535>] of protocol {udp|tcp|sctp}. dest-port-port from 065535.
[exporter-ip <A.B.C.D>] exporter-ip <A.B.C.D>-IP address for the exported traffic.
[protocol-version protocol-version {ipfix|preipfixv9|preipfixv5}-IPFIX protocol
{ipfix|preipfix|preipfixv5}] version.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ipfix enable
ip ipfix enable
You must globally enable IPFIX before you can use any IPFIX commands. This command is critical for offloading the switch from
IPFIX processing.
Syntax
ip ipfix enable
Default
None
Command mode
Global configuration mode
ip ipfix port
Configure IPFIX parameters on a port.
Syntax
ip ipfix [port <portlist>] [enable]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables IPFIX. Use the no operator to disable IPFIX parameters on a port: no ip ipfix
[port <portlist>] [enable]
Selects a hash-key ID. Values range from 14. <1-4>-
hashKeyOne|hashKeyTwo|hashKeyThree|hashKeyFour A 64-bit key is formed based
on the following hash-key-id: Hash Key 1: SIP(lower 20 bits), DIP(lower 19 bits,
hash-key
<1-4> protocol(1-5 bits), srcport(lower 10 bits), dstport(lower 10 bits) Hash Key 2: Cascaded
Hash - Use all bits from 5-tuple - hash1 = hash(SIP,DIP), hash2 = hash(hash1(lower
24 bits,protocol(8 bits), srcport(16 bits),dstport(16 bits)) Hash Key 3: hash(SIP(32
bits),DIP(32 bits)) Hash Key 4: hash(SIP(32 bits),srcport(16 bits),dstport(16 bits)).
hash-
polynomial- Configures the hash polynomial for IPFIX. coeffs <1025-16777215>-polynomial
coeffs coefficients in the range <102516777215>. If you do not specify a coefficient, the
<1025- default value (0x7cc) is used.
16777215>
hash- Configures the hash polynomial for IPFIX. seed <0-16777215>-polynomial seed in the
polynomial- range <016777215> If you do not specify a seed value, the default value (0) is
seed <0-
16777215> used.
sampling- Configures the sampling rate. The sampling rate is expressed as 1 in every n packets.
rate <1- Configure as 1 (the default) for continuous monitoring. Otherwise, specify a different
100000> frequency.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ipfix slot
ip ipfix slot
Configure IPFIX slot parameters.
Syntax
ip ipfix slot <slotList>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
active- Configures flow active timeout. <1-60>-flow record active timeout value from 160
timeout <1-
60> minutes.
aging- Configures flow record aging interval. <10-3600>-flow record aging interval from
interval <10-
3600> 103600 seconds.
exporter- Enables the exporter state. To disable the exporter state, use the following
enable command: no ip ipfix slot <slotlist> exporter-enable
export- Configures the export interval.<10-3600>-frequency of flow export to collector
interval <10-
3600> from 103600 seconds.
template- Configures the value of template refresh timeout for IPFIX. <300-3600>-value in
refresh- seconds from 3003600. The template rate refresh is scheduled for every x seconds
interval
<300-3600> ] or every y exported packets, whichever occurs first.
template-
refresh- Configures the value of template refresh timeout for packets. <10000-100000>-
packets number of packets from 10000100000. The template rate refresh is scheduled for
<10000- every x seconds or every y exported packets, whichever occurs first.
100000>
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip irdp
ip irdp
Enable Router Discovery globally so that the switch supports Router Discovery.
Syntax
ip irdp enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the router discovery protocol on the switch.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip irdp address
ip irdp address
Configure ICMP Router Discovery to enable hosts attached tomulticast or broadcast networks to discover the IP addresses of
theirneighboring routers.
Syntax
ip irdp address <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the IP destination address use for broadcast or multicast router advertisements
address sent from the interface. The address is the all-systems multicast address, 224.0.0.1, or
<A.B.C.D> the limited-broadcast address, 255.255.255.255. The default address is 255.255.255.255.
The default form of this command is default ip irdp address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip mroute interface
ip mroute interface
Configure a multicast route on an interface to customize the time-to-live (TTL) value for the route.
Syntax
ip mroute interface <ipaddr> ttl <1-255>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
ipaddr Indicates the IP address of the selected interface.
Configures the TTL threshold for the multicast route interface. The range, in seconds, is
ttl <1
255> 1255. To set this option to the default value, use the default operator with the
command. The default is 1.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip mroute resource-usage
egress-threshold
Syntax
ip mroute resource-usage egress-threshold <0-32767> ingress-threshold <0-32767>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
egress- Configures the egress record threshold (S,G). A notification message is sent if this value
threshold is exceeded. integer is a value between 032767. To set this option to the default value,
<032767> use the default operator with the command. The default is 0.
ingress- Configures the ingress record threshold (peps). A notification message is sent if this
threshold value is exceeded. integer is a value between 032767. To set this option to the default
<032767> value, use the default operator with the command. The default is 0.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip mroute resource-usage
log-msg trap-msg
Syntax
ip mroute resource-usage log-msg trap-msg
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Configures the notification method for sending only a log message after the threshold
log-msg level is exceeded. Use the no operator to later remove this configuration. To set this
option to the default value, use the default operator with the command. The default is
disabled.
Configures the notification method for sending only a trap message after the threshold
trap-msg level is exceeded. Use the no operator to later remove this configuration. To set this
option to the default value, use the default operator with the command. The default is
disabled.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip mroute static-source-
group
ip mroute static-source-group
Configure static source-group entries in the Distance Vector Multicast Routing Protocol (DVMRP) or Protocol Independent Multicast
(PIM) multicast routing table.
Syntax
ip mroute static-source-group <A.B.C.D> <A.B.C.D/X>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
A.B.C.D Specifies the IP address of the multicast group. Use the no operator to remove this
configuration.
Specifies the multicast source IP address and subnet mask for the static source group
A.B.C.D/X entry. You cannot create duplicate groups. How you configure the source address
depends on the protocol and mode you use. Use the no operator to remove this
configuration.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip mroute stream-limit
ip mroute stream-limit
Limit the number of multicast streams to protect a Switch Fabric/Central Processor Unit (SF/CPU) from multicast data packet
bursts generated by malicious applications.
Syntax
ip mroute stream-limit
Default
None
Command mode
Global configuration mode
Syntax
ip mroute stream-limit interface
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
max- Configures the maximum number of streams on the specified port. The port is shut
allowed- down if the number of streams exceeds this limit. The value is a number between 1
streams 32768. The default value is 1984 streams. To set this option to the default value, use
<integer> the default operator with the command.
max-
allowed- Configures the sampling interval, which is used to check if the number of ingress
streams- multicast streams to the SF/CPU is under a configured limit or if the port needs to shut
timer- down. The range is between 13600. The default value is 10 seconds. To set this
check option to the default value, use the default operator with the command.
<integer>
port Specifies the port or range of ports in slot/port notation. Use the no operator to later
remove this configuration.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip msdp connect-retry
ip msdp connect-retry
Configure the connect-retry period to configure the amount of time, in seconds, between connection attempts for peering
sessions.
Syntax
ip msdp connect-retry <A.B.C.D> <1-65535>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the interval, in seconds, at which the MSDP peer retries the connection, after
the previous connection establishment to the peer fails. The range is from 165535
165535 seconds. The default is 30 seconds. To use the default configuration, use the default
option in the command default ip msdp connect-retry <A.B.C.D> To delete the current
configuration, use the no option in the command no ip msdp connect-retry <A.B.C.D>
A.B.C.D Specifies the IP address of the router that is the MSDP peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip msdp default-peer
ip msdp default-peer
Define a default peer to accept all SA messages from the peer.
Syntax
ip msdp default-peer <A.B.C.D> [route-policy Word<1-64>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
164 Specifies the route policy name to associate with the default peer.
A.B.C.D Specifies the IP address of the router that is the MSDP peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip msdp description
ip msdp description
Configure a peer description to ease the identification of a peer.
Syntax
ip msdp description <A.B.C.D> WORD<1-255>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Word <1255> Specifies the text description up to 255 characters for the peer.
A.B.C.D Specifies the IP address of the router that is the MSDP peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip msdp enable
ip msdp enable
Configure MSDP to enable or disable the MSDP function on the global router.
Syntax
ip msdp enable
Default
The default is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
no Disables MSDP. After you disable MSDP, all MSDP peer sessions end and the system
deletes all local cache entries.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip msdp implicit-default-
peer
ip msdp implicit-default-peer
Configure an implicit default peer to accept all SA messages from the default peer if reverse path forwarding (RPF) peer rule
checks fail.
Syntax
ip msdp implicit-default-peer
Default
The default value is disabled.
Command mode
Global configuration mode
ip msdp keepalive
Configure keepalive messages to adjust the interval at which an MSDP peer sends keepalive messages and the interval at which
the MSDP peer waits for keepalive messages from other peers before it declares them down.
Syntax
ip msdp keepalive <A.B.C.D> <0-21845> <3-65535>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the interval, in seconds, at which the MSDP peer sends keepalive messages. The
range is from 021845 seconds. The default is 60 seconds. A value of 0 indicates the
021845 router does not send keepalive messages after the peers establish the MSDP session. If
you assign a value of 0, Avaya recommends that you configure the interval to wait for
keepalive messages on the other side of the peer relationship as 0.
Specifies the interval, in seconds, at which the MSDP peer waits for keepalive messages
365535 from other peers before it declares them down. The range is from 665535 seconds. The
default is 75 seconds. A value of 0 indicates the MSDP connection is never torn down due
to absence of messages from peer.
A.B.C.D Specifies the IP address of the router that is the MSDP peer. To delete the current
configuration, use the no option in the command no ip msdp keepalive <A.B.C.D>.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip msdp md5-authentication
ip msdp md5-authentication
Configure Message Digest (MD) 5 authentication to secure control messages on the TCP connection between MSDP peers.
Syntax
ip msdp md5-authentication <A.B.C.D> enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the MD5 authentication on MSDP.
no Disables the MD5 authentication when prefixed with the command.
A.B.C.D Specifies the IP address of the router that is the MSDP peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip msdp mesh-group
ip msdp mesh-group
Configure mesh groups to reduce SA flooding.
Syntax
ip msdp mesh-group Word<1-64> <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
164 Specifies the mesh group ID; the name of the mesh group from 164 characters.
A.B.C.D Specifies the IP address of the MSDP router that is the peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip msdp originator-id
ip msdp originator-id
Configure the originator ID to set the RP address field inside the Source-Active (SA) message.
Syntax
ip msdp originator-id <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
A.B.C.D Specifies the IP address to use as the originator ID. If the orig-address is not a system
local address, the system rejects the configuration.
no Deletes the RP address field inside the SA message.
default Uses the default originator ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip msdp password peer
Syntax
ip msdp password peer <A.B.C.D> Word<1-80>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Word <180> Specifies a case-sensitive password, up to 80 characters, for MD5 authentication.
A.B.C.D Specifies the IP address of the router that is the MSDP peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip msdp peer
ip msdp peer
Create an MSDP peer to establish a peering relationship between the local MSDP-enabled router and a peer in another domain.
Avaya recommends that you do not add more than 20 peers.
Syntax
ip msdp peer <A.B.C.D>
Default
The default value is enabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
A.B.C.D Specifies the IP address of the router that is the MSDP peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip msdp redistribute
ip msdp redistribute
Filter Protocol Independent Multicast (PIM) routes to filter which (S,G,RP) entries PIM provides to MSDP.
Syntax
ip msdp redistribute [route-policy Word<1-64>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
164 Specifies the name of the optional route policy. You do not need to create a route policy
to use the redistribution filter.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip msdp sa-filter
ip msdp sa-filter
Filter SA messages to determine which SA messages to accept from a peer and which SA messages to send to a peer.
Syntax
ip msdp sa-filter <in|out> <A.B.C.D> create [route-policy Word<1-64>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
A.B.C.D Specifies the IP address of the router that is the MSDP peer.
<in|out> Creates or modifies an inbound or outbound SA filter for this peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip msdp sa-limit
ip msdp sa-limit
Configure the SA limit to limit the number of SA messages from an MSDP peer that the router stores in the SA cache.
Syntax
ip msdp sa-limit <A.B.C.D> <0-6144>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the maximum number of SA messages from an MSDP peer to keep in the SA
cache. The valid values are from 06144; the default value is 6144. To delete the current
<06144> configuration, use the no option in the commandno ip msdp sa-limit <A.B.C.D> To use
the default configuration, use the default option in the command default ip msdp sa-limit
<A.B.C.D>
A.B.C.D Specifies the IP address of the router that is the MSDP peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip msdp ttl-threshold
ip msdp ttl-threshold
Configure the time-to-live (TTL) threshold to limit which multicast data packets the router sends in SA messages to an MSDP
peer.
Syntax
ip msdp ttl-threshold <A.B.C.D> <1-255>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the time-to-live value, from 1255. The default value is 0, which means that the
1255 router advertises all SA messages. To delete the current configuration, use the no option
in the command no ip msdp ttl-threshold <A.B.C.D> To use the default configuration,
use the default option in the command default ip msdp ttl-threshold <A.B.C.D>
A.B.C.D Specifies the IP address of the router that is the MSDP peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip name-server primary
ip name-server primary
Optionally, add addresses for additional DNS servers.
Syntax
ip name-server primary <word> [secondary <word>] [tertiary <word>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
primary Configures the primary DNS server address. Enter the IP address in a.b.c.d format for
<word> IPv4 or hexadecimal format (string length 046) for IPv6.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ospf
ip ospf
Configure OSPF on an interface that connects to a CE device to exchange route information between the PE node and a customer
site.
Syntax
ip ospf [<1-256>] [vrf <WORD 0-32>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-256> Specifies the interface ID value in the range of 1 to 256.
vrf <WORD 0- Enables passive mode OSPF for the CLIP interface. vrf <WORD 0-32> specifies an
32>] associated VRF by name.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ospf apply accept
Syntax
ip ospf apply accept [vrf <WORD 0-32>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
apply Commits entered changes. Issue this command after modifying any policy
configuration that affects an OSPF accept policy.
[vrf <WORD
0-32>] The name of the VRF.
[vrfids <0-
255>] The ID of the VRF. The value is an integer between 0 and 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ospf apply accept adv-rtr
Syntax
ip ospf apply accept adv-rtr <A.B.C.D>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
adv-rtr <A.B.C.D> Specifies the advertising router IP address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ospf apply redistribute
Syntax
ip ospf apply redistribute <ospf|bgp|static|direct|rip> [vrf <WORD 0-16>] [vrf-src <WORD 0-
16>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<ospf|bgp|static|direct|rip> Specifies the type of routes to be redistributed (the protocol
source).
Specifies the VRF instance by name. When applying a
vrf <WORD 0-16> redistribution instance that redistributes from a nonzero VRF to
VRF 0 (the global router), do not specify the destination VRF;
only specify the source VRF.
vrf-src <WORD 0-16> Specifies the source VRF instance. This parameter is not
required for redistribution within the same VRF.
<ospf|bgp|static|direct|rip> Specifies the type of routes to be redistributed (the protocol
source).
Specifies the VRF instance by name. When applying a
vrf <WORD 0-16> redistribution instance that redistributes from a nonzero VRF to
VRF 0 (the global router), do not specify the destination VRF;
only specify the source VRF.
vrf-src <WORD 0-16> Specifies the source VRF instance. This parameter is not
required for redistribution within the same VRF.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ospf area
ip ospf area
Configure OSPF parameters on a port or VLAN to control how OSPF behaves on the port or VLAN.
Syntax
ip ospf area <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
area Configures the OSPF identification number for the area, typically formatted as an IP
<A.B.C.D> address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ospf bfd
ip ospf bfd
Enable BFD on an OSPF interface.
Syntax
ip ospf [vlan <1-4094>/port <portNum>] bfd
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
ospf Enables BFD on an Open Shortest Path Forst (OSPF) interface.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ospf enable
ip ospf enable
Enable OSPF on MPLS trunk ports.
Syntax
ip ospf enable
Default
None
Command mode
Global configuration mode
ip ospf redistribute
Configure a redistribute entry to announce certain routes into the RIP domain, including static routes, direct routes, RIP, OSPF, or
BGP. Optionally, use a route policy to control the redistribution of routes.
Syntax
ip ospf redistribute <ospf|bgp|static|direct|rip>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<ospf|bgp|static|direct|rip> Specifies the type of routes to be redistributed (the protocol
source).
vrf <WORD 0-16> Specifies the VRF instance.
vrf-src <WORD 0-16> Specifies the source VRF instance. This parameter is not
required for redistribution within the same VRF.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ospf redistribute bgp
Syntax
ip ospf redistribute bgp
Default
None
Command mode
Global configuration mode
Syntax
ip ospf redistribute bgp enable vrf-src <vrfName>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
vrfName Specifies of the name of the VRF.
Specifies the VRF instance name to which to apply redistribution. To redistribute routes
vrf-src
<vrfName> from VRF 0, explicitly specify vrf-src 0. Otherwise, the command redistributes routes
within the same VRF.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ospf redistribute isis
metric-type
Syntax
ip ospf redistribute isis metric-type {type1 | type2}
Default
None
Command mode
VRF router configuration mode
Command parameters
Parameter Description
{type1} Specifies a type 1 metric. For metric type 1, the cost of the external routes is equal to the
sum of all internal costs and the external cost.
{type2} Specifies a type 2 metric. For metric type 2, the cost of the external routes is equal to the
external cost alone. The default is type 2.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ospf redistribute isis
subnets
Syntax
ip ospf redistribute isis subnets {allow | suppress}
Default
None
Command mode
VRF router configuration mode
Command parameters
Parameter Description
[allow] Allows external subnet route advertisements.
[suppress] Suppresses external subnet route advertisements.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ospf spf-run
ip ospf spf-run
Force the switch to update its shortest-path calculations so that the switch uses the latest OSPF routing information.
Syntax
ip ospf spf-run [vrf <WORD 0-16>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf <WORD 0-16> Specifies a VRF instance by name.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip pgm enable
ip pgm enable
Configure PGM globally on the switch to provide reliable, duplicate-free delivery of data packets while reducing network
congestion.
Syntax
ip pgm enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Configures the maximum number of retransmit state entries that the switch can
max-rexmit- create. Each entry uses a unique NAK sequence number. The default value is
state <integer> 200 entries. To set this option to the default value, use the default operator
with the command.
max-sessions Configures the maximum number of source path state sessions allowed on the
<integer> switch. The default value is 100 sessions. To set this option to the default
value, use the default operator with the command.
When enabled, the DLR that receives redirected NAKs, where it uses the
nnak-generate retransmitted data (RDATA), sends an NNAK to the original source. Use the no
<enable|disable> operator to later remove this configuration. To set this option to the default
value, use the default operator with the command. The default is enabled.
Specifies the length of idle time (in seconds) before a session times out. Idle
session-life- time is when the switch does not receive SPMs from the upstream router. The
time <integer> default value is 300 seconds. To set this option to the default value, use the
default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip pgm enable vlan
Syntax
ip pgm enable vlan
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
max-nak- Specifies how long to wait for RDATA (in milliseconds) after receiving a NAK
rdata-int confirmation (NCF). The default value is 10000 milliseconds. To set this option to the
<integer> default value, use the default operator with the command.
max-nak- Configures the maximum number of NAK retransmission packets allowed for each
re-xmit- second. The default value is 2 pps. To set this option to the default value, use the
cnt
<integer> default operator with the command.
Specifies the length of time (in milliseconds) during which a network element (NE)
nak- eliminates duplicate NAKs. After this interval expires, the NE suspends NAK elimination
eliminate- until the first duplicate arrives. After this NAK is forwarded, the NE eliminates duplicate
int NAKs for the specified interval. You must configure this parameter lower than max-nak-
<integer> rdata-int. The default value is 5000 milliseconds. To set this option to the default value,
use the default operator with the command.
nak-re- Specifies how long to wait for an NCF (in milliseconds), before retransmitting the NAK.
xmit-int The default value is 1000 milliseconds. To set this option to the default value, use the
<integer> default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip pim bsr-candidate
preference value ethernet port
Syntax
ip pim bsr-candidate preference <value>
Default
None
Command mode
Global configuration mode
Syntax
ip pim bsr-candidate preference <value>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Enables the C-BSR on this interface and configures its preference value, from 1255, to
become a BSR. The C-BSR with the highest BSR preference and address is the
preference
<value> preferred BSR. The default is 1, which indicates that the current interface is not a C-
BSR. To set this option to the default value, use the default operator with the
command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip pim enable
ip pim enable
Enable PIM-SM on the VLAN to enable IGAP configuration.
Syntax
ip pim enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Globally activates PIM on the switch. To set this option to the default value, use the
default operator with the command. The default is disabled.
<vid> Specifies the VLAN id. The range is between 1 and 4094. The default value is 1.
enable Enables IGAP on the switch.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip pim enable ethernet port
Syntax
ip pim enable ethernet port
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables PIM on the local switch interface. To set this option to the default value, use the
default operator with the command. The default is disabled.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip pim enable vlan
Syntax
ip pim enable vlan
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables PIM on the local switch interface. To set this option to the default value, use the
default operator with the command. The default is disabled.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip pim enable vrf
Syntax
ip pim enable vrf
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Globally activates PIM on the switch. To set this option to the default value, use the
default operator with the command. The default is disabled.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip pim mbr
ip pim mbr
Enable the MBR functionality on an Avaya Ethernet Routing Switch 8800/8600 to connect a PIM-SM domain to a DVMRP domain.
Syntax
ip pim mbr
Default
None
Command mode
Global configuration mode
Syntax
ip pim mode sparse
Default
None
Command mode
Global configuration mode
Syntax
ip pim mode ssm
Default
None
Command mode
Global configuration mode
ip pim static-rp
Configure a static RP to configure a static entry for an RP.
Syntax
ip pim static-rp <A.B.C.D/X> <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the IP address and address mask of the multicast group. When combined, the
A.B.C.D/X IP address and address mask identify the range of the multicast addresses that the RP
handles.
A.B.C.D Specifies the IP address of the static RP.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip pim virtual-neighbor
ip pim virtual-neighbor
Configure a virtual neighbor when the next hop for a static route cannot run PIM.
Syntax
ip pim virtual-neighbor <ipaddr> <ipaddr>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
ipaddr The first IP address indicates the IP address of the selected interface.
ipaddr The second IP address Indicates the IP address of the neighbor.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip prefix-list
ip prefix-list
Create one or more IP prefix lists and apply those lists to an IP route policy.
Syntax
ip prefix-list <1-1024> <prefix/len> [<ge|le> <0-32>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Creates or adds a prefix to the list.<prefix/len> specifies the IP address and network
<prefix/len> mask in the format a.b.c.d/x, a.b.c.d/x.x.x.x, or default. <ge|le> specifies greater
[<ge|le> than or equal to or less than or equal to. <0-32> specifies the mask length in the
<0-32>] range 0 to 32. The no form of this command is no ip prefix-list <1-1024>
<prefix/len>.
Adds a prefix entry to the prefix list. A.B.C.D/0-32 is the IP address and mask.
<A.B.C.D/0- <ge|le> <0-32> Lower bound and higher bound mask lengths together can define a
32> [<ge|le>
<0-32>] range of networks. Use the no operator to remove a prefix entry from the prefix list:
no ip prefix-list <WORD 1-64> <A.B.C.D/0-32>
name <WORD
1-64> Renames the specified prefix list. The name length is from 1 to 64 characters.
vrf <WORD
0-32> The name of the VRF.
vrfids <0-
255> The ID of the VRF and is an integer in the range of 0 to 255.
name <name> Renames the specified prefix list. The name can contain 164 characters.
prefix- Indicates the name of the specified prefix list, which is a string length from 164
list-name characters. Use the no operator to later remove this configuration.
Adds a prefix entry to the prefix list. Specify the IP address in the format a.b.c.d/x or
IP address a.b.c.d/x.x.x.xImportant Lower boundaries and higher boundaries of the mask
lengths together can define a range of networks. Use the no operator to later
remove this configuration.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip redistribute enable
ip redistribute enable
Configure and enable redistribution entries to allow a protocol toannounce routes of a certain source type, for example, static, RIP,
or direct.
Syntax
ip <rip|ospf|bgp> redistribute <ospf|bgp|static|direct|rip> enable [vrf-src <WORD 0-16>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable [vrf-src <vrf-name>] Enables the OSPF route redistribution instance.
<ospf|bgp|static|direct|rip> Specifies the type of routes to redistribute-the protocol source.
vrf <WORD 0-16> Specifies the VRF instance.
vrfids <0-255> Specifies a list of VRF IDs.
vrf-src <WORD 0-16> Specifies the source VRF instance. This parameter is not
required for redistribution within the same VRF.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip redistribute isis
ip redistribute isis
Configure a redistribute entry to announce certain routes into the domain, including BGP, OSPF, and RIP routes.
Syntax
ip {bgp | ospf | rip} redistribute isis
Default
None
Command mode
VRF router configuration mode
Command parameters
Parameter Description
{bgp | ospf | rip} Specifies the type of routes to be redistributed (the protocol source).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip redistribute isis enable
Syntax
ip {bgp | ospf | rip} redistribute isis enable
Default
None
Command mode
VRF router configuration mode
Command parameters
Parameter Description
{bgp | ospf | rip} Specifies the type of routes to be redistributed (the protocol source).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip redistribute isis metric
Syntax
ip {bgp | ospf | rip} redistribute isis metric <0-65535>
Default
None
Command mode
VRF router configuration mode
Command parameters
Parameter Description
{bgp | ospf | rip} Specifies the type of routes to be redistributed (the protocol source).
<value> Type a metric value between 065535.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip redistribute isis route-
policy
Syntax
ip {ospf | rip}redistribute isis route-policy <WORD 0-64>
Default
None
Command mode
VRF router configuration mode
Command parameters
Parameter Description
{ospf | rip} Specifies the type of routes to be redistributed (the protocol source).
<WORD 064> Specifies the policy name. Type a name between 064 characters in length.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip rip
ip rip
Configure RIP on Ethernet ports and VLANs so that they can participate in RIP routing.
Syntax
ip rip
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Sets the RIP Default Import Metric; default value is 8. This value is used by rip
default-
metric announce of OSPF internal routes if the policy does not specify metric. 0 is used for
deconfiguration.
domain Sets the RIP domain value.
enable Enables the RIP on a particular VRF.
redistribute Specifies the RIP redistribution configuration commands.
timers Specifies the RIP timer configuration commands.
cost <1-15> Configures the RIP cost for this port (link).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip rip apply redistribute
Syntax
ip rip apply redistribute <ospf|bgp|static|direct|rip> [vrf <WORD 0-16>] [vrf-src <WORD 0-
16>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<ospf|bgp|static|direct|rip> Specifies the type of routes to be redistributed (the protocol
source).
Specifies the VRF instance by name. When applying a
vrf <WORD 0-16> redistribution instance that redistributes from a nonzero VRF to
VRF 0 (the global router), do not specify the destination VRF;
only specify the source VRF.
vrf-src <WORD 0-16> Specifies the source VRF instance. This parameter is not
required for redistribution within the same VRF.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip rip out-policy
ip rip out-policy
Assign the policy to the RIP interface.
Syntax
ip rip out-policy <WORD 0-32>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<WORD 0-32> Specify the name of the route policy.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip rip redistribute
ip rip redistribute
Configure a redistribute entry to announce certain routes into the RIP domain, including static routes, direct routes, RIP, OSPF, or
BGP. Optionally, use a route policy to control the redistribution of routes.
Syntax
ip rip redistribute <ospf|bgp|static|direct|rip>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<ospf|bgp|static|direct|rip> Specifies the type of routes to be redistributed (the protocol
source).
vrf <WORD 0-16> Specifies the VRF instance.
vrf-src <WORD 0-16> Specifies the source VRF instance. This parameter is not
required for redistribution within the same VRF.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip rip redistribute bgp
enable
Syntax
ip rip redistribute bgp enable [vrf-src <vrfName>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the redistribution instance on the VRF.
Specify the VRF instance name to which to apply redistribution. To redistribute routes
vrf-src
<vrfName> from VRF 0, explicitly specify vrf-src 0. Otherwise, the command redistributes routes
within the same VRF.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip route
ip route
Configure a black hole static route to the destination a router advertises to avoid routing loops when aggregating or injecting
routes to other routers.
Syntax
ip route <A.B.C.D> <A.B.C.D> 255.255.255.255 enable [next-hop-vrf <WORD 0-16>]
ip route <IP address> <network mask> <next-hop> weight <value> [preference <1-255>] [local-
next-hop enable] enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
{A.B.C.D} The first and second <A.B.C.D> specify the IP address and mask for the route
destination. 255.255.255.255 is the black hole route.
enable Adds a static or default route to the router or VRF. The no form of this command is no
ip route <A.B.C.D> <A.B.C.D> 255.255.255.255 enable
Enables the local next hop for this static route. The default form of this command is
local- default ip route <A.B.C.D> <A.B.C.D> <A.B.C.D> local-next-hop enable. The no form
next-hop
enable of this command is no ip route <A.B.C.D> <A.B.C.D> 255.255.255.255 local-next-hop
enable
IP
address Specifies the destination IP address in the format A.B.C.D
Enables or disables this option. True indicates that the static route becomes active only
local- if the switch uses a local route to the network. False indicates that the static route
next-hop becomes active if the switch uses a local route or a dynamic route. Use the no operator
enable to later remove this configuration. To configure this option to the default value, use the
default operator with the command.
network
mask Specifies the network mask in the format A.B.C.D
next-hop Specifies the IP address for the next hop.
Configures the preference for the static route in the range 1255. You can configure
preference different preferences for multiple static routes to the same destination. Use the no
<1-255> operator to later remove this configuration. To configure this option to the default
value, use the default operator with the command.
weight Configures the cost for the static route. The lower the cost, the more preferable the
<value> route.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip route bfd
ip route bfd
Enable BFD on a static route.
Syntax
ip route bfd <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
route Enables BFD on a static route.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip route default
ip route default
The default route specifies a route to all networks for which there are no explicit routes in the Forwarding Information Base or the
routing table. This route has a prefix length of zero (RFC1812). You can configure routing switches with a static default route, or
they can learn it through a dynamic routing protocol.To create a default static route, you configure the destination address and
subnet mask to 0.0.0.0.
Syntax
ip route 0.0.0.0 0.0.0.0 <A.B.C.D> enable [next-hop-vrf <WORD 0-16>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<A.B.C.D> <A.B.C.D> specifies the IP address of the next-hop router (the next router at which
packets must arrive on this route).
enable Adds a static or default route to the router or VRF. The no form of this command is no ip
route 0.0.0.0 0.0.0.0 <A.B.C.D> enable
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip route preference
ip route preference
Syntax
ip route preference protocol <static|ospf-intra|ospf-inter|ebgp|ibgp|rip|ospf-extern1|ospf-
extern2|staticv6|ospfv3-intra|ospfv3-inter|ospfv3-extern1|ospfv3-extern2> <0-255>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
protocol <static|ospf-
intra|ospf- Configures the preference value for the specified protocol. If two
inter|ebgp|ibgp|rip|ospf- protocols have the same configured value, the default value is
extern1|ospf- used. The protocol must be one of the following: static, ospf-intra,
extern2|staticv6|ospfv3-
intra|ospfv3- ospf-inter, ebgp, ibgp, rip, ospf-extern1, ospf-extern2, staticv6,
inter|ospfv3- ospfv3-intra, ospfv3-inter, ospfv3-extern1, or ospfv3-extern2. <0-
extern1|ospfv3-extern2> 255> configures the priority. 0 is reserved for local routes.
<0-255>
vrf <WORD 0-16> Specifies a VRF instance by VRF name.
vrfids <WORD 0-255> Specifies a VRF instance by VRF number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip route preference protocol
spbm-level1
Syntax
Ip route preference protocol spbm-level1 <0-255>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<value> Type a preference value from 0-255; 0 is reserved for local routes.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip routing
ip routing
Enable IP forwarding (routing) on a global level so that the router supports routing. You can use the IP address of any router
interface for IP-based network management.
Syntax
ip routing
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
routing Enables IP routing.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip rsmlt
ip rsmlt
Configure Routed Split MultiLink Trunking (RSMLT) on each IP VLAN interface.
Syntax
ip rsmlt holddown-timer <0-3600>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Defines how long the RSMLT switch does not participate in Layer 3 forwarding. 0-3600 is
holddown- the timer value in seconds. To set this value to the default value, use the default
timer
<0-3600> operator with this command. Avaya recommends that you configure this value to be
longer than the anticipated routing protocol convergence.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip rsmlt edge-support
ip rsmlt edge-support
Configure RSMLT-edge to store the RSMLT peer MAC/IP address-pair in its local config file and restore the configuration if the
peer does not restore after a simultaneous reboot of both RSMLT-peer switches.
Syntax
ip rsmlt edge-support
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
vlan ID The ID of the VLAN in the range of 1 to 4094.
edge-support Enables RSMLT-edge support.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip rvs-path-chk mode port
Syntax
ip rvs-path-chk mode <exist-only|strict>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the mode for reverse path checking. In exist-only mode, reverse path
mode checking checks whether the source IP address of the incoming packet exists in the
<exist- routing table. In strict mode, reverse path checking checks whether the source IP
only|strict> address of the incoming packet exists in the routing table. To set this option to the
default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip rvs-path-chk mode vlan
Syntax
ip rvs-path-chk mode <exist-only|strict>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the mode for reverse path checking. In exist-only mode, reverse path
mode checking checks whether the source IP address of the incoming packet exists in the
<exist- routing table. In strict mode, reverse path checking checks whether the source IP
only|strict> address of the incoming packet exists in the routing table. To set this option to the
default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip-source-address
ip-source-address
Specify the CLIP interface as the source address for SPBM Native IP shortcuts.
Syntax
ip-source-address <A.B.C.D>
Default
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
<A.B.C.D> <A.B.C.D> specifies the network IP address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip static-mroute
ip static-mroute
Configure a multicast static route to separate unicast and multicast traffic streams for Reverse Path Forwarding (RPF) calculation.
Syntax
ip static-mroute <A.B.C.D/0-32> rpf <A.B.C.D> [preference <1-255>] [enable]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
1255 Specifies a preference value from the range 1255. The default value is 1. To set this
option to the default value, use the default operator with the command.
A.B.C.D Specifies the IP address of the RPF neighbor or the static route.
A.B.C.D/0-
32 Specifies the IP address and the network mask for the route.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip ttl
ip ttl
Configure the IP routing protocol stack to specify which routing features the switch can use.
Syntax
ip ttl <1-255>
Default
The default value is 255.
Command mode
Global configuration mode
Command parameters
Parameter Description
Configures the default time-to-live (TTL) value for a routed packet. The TTL is the
ttl <1- maximum number of seconds before a packet is discarded. The default value of 255 is
255> used whenever a time is not supplied in the datagram header. The default form of this
command is default ip ttl.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 area
ipv6 area
Create and configure an OSPF area.
Syntax
ipv6 area <A.B.C.D> default-cost <cost> import <value> [import-summaries enable]
translator-role <value> type <nssa|stub>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Stub default metric for this stub area. cost is the range from 0 to 16777215. This is
default-
cost <cost> the metric value applied at the indicated type of service. To set this option to the
default value, use the default operator with the command.
Configures the area support for importing advertisements. The options are:external-
import Stub and nssa are both false noexternal-Set the area as stub area nssa-Set the area
<value> as nssa To set this option to the default value, use the default operator with the
command.
import- Configures the area support for importing summary advertisements into a stub area.
summaries Use this entry only for a stub area. To set this option to the default value, use the
enable default operator with the command.
translator- Indicates an NSSA Border router ability to perform translation of type-7 LSAs into
role
<value> type-5 LSAs Default is 1, the candidate value is 2.
Configures the type of area. An NSSA prevents flooding of normal route
type
<nssa|stub> advertisements into the area by replacing them with a default route. A stub area uses
only one exit point (router interface) out of the area.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 area range
Syntax
ipv6 area range <A.B.C.D> <Ipv6 address/prefix> <inter-area-prefix-link|nssa-extlink>
advertise-mode <advertise|not-advertise>] advertise-metric <0-65535>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
A.B.C.D Specifies the IP address of the area.
advertise-metric <065535> Specifies the advertise metric value and LSA type.
advertise-mode Specifies the area range advertise mode as advertise or not-
<advertise|not-advertise> advertise.
ipv6addrress/prefix Configures the IPv6 address range of an OSPF area. The string
length is 0255 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 area virtual-link
Syntax
ipv6 area virtual-link <area IP address> <virtual link IP address> dead-interval <seconds>
hello-interval <seconds> retransmit-interval <seconds> transit-delay <seconds>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
dead- Specifies the dead interval, in seconds, as a range 14 095. To set this option to the
interval
<seconds> default value, use the default operator with the command.
hello- Specifies the Hello interval, in seconds, sent between switches for a virtual interface in
interval an OSPF area. The range is 165535. To set this option to the default value, use the
<seconds> default operator with the command.
retransmit- Specifies the retransmit interval, in seconds, sent between switches for a virtual
interval interface in an OSPF area. The range is 11800. To set this option to the default
<seconds> value, use the default operator with the command.
transit- Specifies the transit delay interval, in seconds, sent between switches for a virtual
delay interface in an OSPF area. The range is 11800. To set this option to the default
<seconds> value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 as-boundary-router
enable
Syntax
ipv6 as-boundary-router enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
as-boundary-router enable Enables the OSPF autonomous system boundary router.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 dhcp-relay
ipv6 dhcp-relay
Configure DHCP relay parameters on the specified port or VLAN..
Syntax
ipv6 dhcp-relay
Default
None
Command mode
Interface configuration mode
Syntax
ipv6 dhcp-relay fwd-path <agent-addr> <server-addr> [enable]
Default
The default is disable.
Command mode
Global configuration mode
Syntax
ipv6 icmp error-interval <0-2147483647>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
error-interval Configures the error interval in milliseconds. The interval is the time between
<0 through transmission of error messages. To set this option to the default value, use the
2147483647> default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 interface address
Syntax
ipv6 interface address <ipv6 address> vlan <vlan id>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
address <ipv6 Configures the IPv6 address and prefix length in the format address/prefix
address> length.
vlan <vlan id> Specifies the VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 interface address vlan
Syntax
ipv6 interface address <ipv6 address>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
address <ipv6 address> Configures the IPv6 address or prefix length.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 interface multicast-
routing
Syntax
ipv6 interface multicast-routing [reachable-time <value>] [retransmit-timer <value>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
reachable-time Configures the reachable time, in milliseconds, for the interface. The range is 0
<value> 3600000.
retransmit- Configures the time between attempts to transmit multicast packets, in
timer <value> milliseconds, for the interface. The range is 03600000.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 interface multicast-
routing brouter
Syntax
ipv6 interface multicast-routing [reachable-time <value>] [retransmit-timer <value>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
reachable-time Configures the reachable time, in milliseconds, for the interface. The range is 0-
<value> 3600000.
retransmit- Configures the time between attempts to transmit multicast packets, in
timer <value> milliseconds, for the interface. The range is 0-3600000.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 mgmt-virtual
ipv6 mgmt-virtual
Configure a system virtual IPv6 address to manage of the SF/CPU Ethernet port in failover situations.
Syntax
ipv6 mgmt-virtual <ipv6address/prefixlen>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the IPv6 address and prefix length to add to the port. To set
ipv6address/prefixlen this option to the default value, use the default operator with the
command: default ipv6 mgmt-virtual.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 mld
ipv6 mld
Configure Multicast Listener Discovery (MLD) on a VLAN to customize the configuration.
Syntax
ipv6 mld [last-memb-query-int <value>] [query-interval <value>] [query-max-response-time
<value>] [robustval <value>] [version <1|2>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
last-memb-query- Configures the query interval time in 1/10 of a second for the last member.
int <value> value is in the range 065535.
query-interval Configures the maximum query response time advertised in MLD queries on
<value> this interface. value is in the range 065535.
query-max- Configures the query interval time in 1/10 of a second for the last member.
response-time
<value> value is in the range 065535.
robustval <value> Configures the robustness value. value is in the range 065535.
version <1|2> Configures the version of MLD to version 1 or version 2.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 mld brouter
Syntax
ipv6 mld [last-memb-query-int <value>] [query-interval <value>] [query-max-response-time
<value>] [robustval <value>] [version <1|2>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
last-memb-query- Configures the query interval time in 1/10 of a second for the last member.
int <value> value is in the range 065535.
query-interval Configures the query interval time in 1/10 of a second. value is in the
<value> range 065535.
query-max- Configures the maximum query response time advertised in MLD queries on
response-time
<value> this interface. value is in the range 065535.
robustval <value> Configures the robustness value. value is in the range 065535.
version <1|2> Configures the version of MLD to version 1 or version 2.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 multicast-routing
ipv6 multicast-routing
Enable the router for multicast traffic to enable MLD globally.
Syntax
ipv6 multicast-routing
Default
None
Command mode
Global configuration mode
ipv6 nd
Configure route advertisement to discover potential default routers in a network, and to discover link information.
Syntax
ipv6 nd [dad-ns <0-600>] [hop-limit <1-255>] [managed-config-flag] [other-config-flag]
[ra-lifetime <0|4-9000>] [rtr-advert-max-interval <4-1800>] [rtr-advert-min-interval <3-
1350>] [send-ra]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
The number of neighbor solicitation messages from duplicate address detection. The
dad-ns acceptable range is 0 through 600. A value of 0 disables duplicate address detection on
the specified interface. A value of 1 configures a single transmission without follow-up
transmissions. Use the default operator to set this value to the default setting.
hop- Enter the maximum number of hops before packets drop. Use the default operator to set
limit this value to the default setting.
managed- Set to true to enable M-bit (managed address configuration) on the router. Use the no
config- operator to remove this option. Use the default operator to set this value to the default
flag setting.
Set to true to enable the O-bit (other stateful configuration) in the router advertisement.
other- Other stateful configuration autoconfigures received information without addresses. Use
config-
flag the no operator to remove this option. Use the default operator to set this value to the
default setting.
Enter the router lifetime included in router advertisement. Other devices use this
ra-
lifetime information to determine if the router can be reached. The range is 0 or 49000. Use the
default operator to set this value to the default setting.
rtr-
advert- Configures the maximum time allowed between sending unsolicited multicast router
max- advertisements.
interval
rtr- Configures the minimum time allowed between sending unsolicited multicast router
advert- advertisements from the interface, in seconds. (31350 seconds). Use the default
min-
interval operator to set this value to the default setting.
send-ra Enable or disable periodic router advertisement messages. Use the no operator to remove
this option. Use the default operator to set this value to the default setting.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 nd prefix
ipv6 nd prefix
Set neighbor discovery prefix parameters.
Syntax
ipv6 nd prefix <prefix/prefix length> [infinite] [no-advertise] [preferred-life <seconds>]
[valid-life <seconds>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
infinite Configures the prefix as infinite.
preferred-life Configures the preferred life, in seconds. The valid range is 03600000. Use the
<seconds> default operator to set this value to the default setting.
prefix/prefix
length Specifies the IP address and prefix.
valid-life Configures the valid life, in seconds. The valid range is 03600000. Use the
<seconds> default operator to set this value to the default setting.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 nd prefix-interface
ipv6 nd prefix-interface
Configure discovery prefixes to discover link-layer addresses and to obtain and advertise various network parameters and
reachability information.
Syntax
ipv6 nd prefix-interface < Ipv6address-prefix> [no-autoconfig <false|true>] [eui <1-3>]
[no-advertise] [no-onlink <false|true>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
no-
autoconfig If true, the prefix is used for autonomous address configuration.
<false|true>
eui <1-3> (1) eui (extended unique identifier) not used, (2) eui with U/L (Universal/Local bit)
complement enabled, (3) eui used without u/l.
no-advertise Removes the prefix from the neighbor advertisement. Use the no operator to
remove this option. Use the default operator to set this value to the default setting.
no-onlink If true, onlink determination uses the prefix. This value is placed in the L-bit field in
<false|true> the prefix information option. It is a 1-bit flag.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 neighbor
ipv6 neighbor
Add neighbors to the cache manually.
Syntax
ipv6 neighbor <ipv6 address> port <slot/port> mac <mac address> vlan <vlan id>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
ipv6
address Specifies the IPv6 address in hexadecimal colon format {string length 0..128}.
Syntax
ipv6 ospf area <A.B.C.D> cost <metric> [dead-interval <seconds>] [hello-interval
<seconds>][network <value>][priority <value>] [retransmit-interval <seconds>] [transit-
delay <seconds>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
area
<A.B.C.D> Specifies the area IP address (0.0.0.0 to 255.255.255.255) {a.b.c.d}.
Configures the OSPF metric for the interface. The switch advertises the metric in
cost
<metric> router link advertisements. metric is the range 065535. To set this option to the
default value, use the default operator with the command.
Configures the OSPF dead interval for the interface. seconds is the number of seconds
dead- the switch OSPF neighbors wait before determining that this OSPF router is down.
interval The range is from 14095. This value must be at least four times the Hello interval
<seconds> value. The default is 40. To set this option to the default value, use the default
operator with the command.
Configures the OSPF hello interval for the interface. seconds is the number of seconds
hello- between hello packets sent on this interface. The range is 165535. The default is 10.
interval Important When you change the hello interval values, you must save the configuration
<seconds> file and reboot the switch for the values to be restored and checked for consistency.
To set this option to the default value, use the default operator with the command.
network Configures the type of interface. The choices are:eth-broadcast nbma-NBMA p2mp-
<value> point-to-multipoint p2p-point-to-point
poll- Configures the polling interval for the OSPF interface in seconds. seconds is 0
interval 2147483647. To set this option to the default value, use the default operator with the
<seconds> command.
Configures the OSPF priority for the interface during the election process for the
designated router. The interface with the highest priority number is the designated
router. The interface with the second-highest priority becomes the backup designated
priority
<value> router. If the priority is 0, the interface cannot become either the designated router or
a backup. The priority is used only during election of the designated router and
backup designated router. value is in the range 0255. The default is 1. To set this
option to the default value, use the default operator with the command.
Configures the retransmit interval for the OSPF interface; the number of seconds
retransmit-
interval between link-state advertisement retransmissions. seconds is an integer between 11
<seconds> 800. To set this option to the default value, use the default operator with the
command.
Configures the transit delay time for the OSPF interface, the estimated time in
transit- seconds it takes to transmit a link-state update packet over the interface. seconds is
delay
<seconds> an integer between 11 800. To set this option to the default value, use the default
operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 ospf area vlan
Syntax
ipv6 ospf area <A.B.C.D> cost <metric> [dead-interval <seconds>] [hello-interval
<seconds>][network <value>][priority <value>] [retransmit-interval <seconds>] [transit-
delay <seconds>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
area
<A.B.C.D> Specifies the area IP address (0.0.0.0 to 255.255.255.255) {a.b.c.d}.
Configures the OSPF metric for the interface. The switch advertises the metric in
cost
<mtric> router link advertisements. metric is the range 065535. To set this option to the
default value, use the default operator with the command.
Configures the OSPF dead interval for the interface. seconds is the number of seconds
dead- the switch OSPF neighbors wait before determining that this OSPF router is down.
interval The range is from 14095. This value must be at least four times the Hello interval
<seconds> value. The default is 40. To set this option to the default value, use the default
operator with the command.
Configures the OSPF hello interval for the interface. seconds is the number of seconds
between hello packets sent on this interface. The range is 165 535. The default is
hello- 10. Important When you change the hello interval values, you must save the
interval
<seconds> configuration file and reboot the switch for the values to be restored and checked for
consistency. To set this option to the default value, use the default operator with the
command.
network Configures the type of interface. The choices are:eth-broadcast nbma-NBMA p2mp-
<value> point-to-multipoint p2p-point-to-point
poll- Configures the polling interval for the OSPF interface in seconds. seconds is between
interval 02147483647. To set this option to the default value, use the default operator with
<seconds> the command.
Configures the OSPF priority for the interface during the election process for the
designated router. The interface with the highest priority number is the designated
router. The interface with the second-highest priority becomes the backup designated
priority
<value> router. If the priority is 0, the interface cannot become either the designated router or
a backup. The priority is used only during election of the designated router and
backup designated router. value is in the range 0255. The default is 1. To set this
option to the default value, use the default operator with the command.
Configures the retransmit interval for the OSPF interface; the number of seconds
retransmit-
interval between link-state advertisement retransmissions. seconds is an integer between 1
<seconds> 1800. To set this option to the default value, use the default operator with the
command.
Configures the transit delay time for the OSPF interface, the estimated time in
transit- seconds it takes to transmit a link-state update packet over the interface. seconds is
delay
<seconds> an integer between 11800. To set this option to the default value, use the default
operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 ospf enable
Syntax
ipv6 ospf enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the OSPF on the ipv6 interface.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 ospf enable vlan
Syntax
ipv6 ospf enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the OSPF on the ipv6 VLAN interface.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 ospf nbma-nbr
Syntax
ipv6 ospf nbma-nbr <Ipv6address/prefix-len> priority <priority>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Ipv6address/prefix-
len Specifies the IPv6 address of the neighbor as a string of 043.
Configures the OSPF priority for the interface during the election process
for the designated router. The interface with the highest priority number is
the designated router. The interface with the second-highest priority
priority becomes the backup designated router. If the priority is 0, the interface
<priority> cannot become either the designated router or a backup. The priority is
used only during election of the designated router and backup designated
router. The range is 0 to 255. The default is 1. To set this option to the
default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 ospf nbma-nbr vlan
Syntax
ipv6 ospf nbma-nbr <Ipv6address/prefix-len> priority <priority>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Ipv6address/prefix-
len Specifies the IPv6 address of the neighbor as a string of 043.
Configures the OSPF priority for the VLAN during the election process for
the designated router. The interface with the highest priority number is the
designated router. The interface with the second-highest priority becomes
priority the backup designated router. If the priority is 0, the interface cannot
<priority> become either the designated router or a backup. The priority is used only
during election of the designated router and backup designated router. The
range is 0 to 255. The default is 1. To set this option to the default value,
use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 redistribute direct
Syntax
ipv6 redistribute direct enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
static enable Enables or disables static redistribution to redistribute IPv6 static routes.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 route
ipv6 route
Configure IPv6 static routes to change static routes directly with the IPv6 static routing table manager.
Syntax
ipv6 route <Ipv6 address/prefix> enable [next-hop <Ipv6 address/prefix>] [port <slot/port>]
[tunnel <tunnel-id>] [vlan <vlan id>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Adds a static or default route to the switch. ipv6address/prefix is the IP address
and prefix for the route destination as a string 046 characters. next-hop
enable [next- <value> is the IP address of the next-hop router; the next router at which
hop <Ipv6
address/prefix>] packets must arrive on this route. The string length is 046 characters. When
creating a black hole static route, set this field to 255.255.255.255 as the IP
address of the router through which the specified route is accessible.
port <value> Specifies the slot and the port number.
vlan <value> Specifies the VLAN ID in the range of 14094.
tunnel <value> configures the tunnel ID in the range of 12147483647.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 tunnel
ipv6 tunnel
Create a tunnel to transfer traffic between IPv6 devices in an IPv4 network. Configure manual tunnels when you want to define
both the local and destination addresses.
Syntax
ipv6 tunnel <tunnel id> source <A.B.C.D> address <ipv6 address/prefix-len> destination
<A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
address <ipv6 Configures the local address for the tunneled device in IPv6/prefix-
address/prefix-len> length format.
destination <A.B.C.D> Configures the address for the device that is tunneled to in IPv4 or
IPv6/prefix-length format.
source <A.B.C.D> Configures the address for the local device.
tunnel id Specifies the ID number of the tunnel in the range of 1
2147483647.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 tunnel vlan
Syntax
ipv6 tunnel <tunnel id> [dead-interval <seconds>] enable [hello-interval <seconds>] [metric
<value>] [poll-interval <seconds>] [priority <value>] [retransmit-interval <seconds>]
[transit-delay <seconds>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
area
<A.B.C.D> Configures the area IP address (0.0.0.0 to 255.255.255.255) {a.b.c.d}.
Configures the OSPF dead interval for the interface. seconds is the number of seconds
dead- the switch OSPF neighbors wait before determining that this OSPF router is down.
interval The range is from 1-4095. This value must be at least four times the hello interval
<seconds> value. The default is 40. To set this option to the default value, use the default
operator with the command.
enable Configures the state (enabled or disabled) of the OSPF interface. To set this option to
the default value, use the default operator with the command.
Configures the OSPF Hello interval for the interface. seconds is the number of seconds
hello- between hello packets sent on this interface. The range is 165535. The default is 10.
interval Important When you change the hello interval values, you must save the configuration
<seconds> file and reboot the switch for the values to be restored and checked for consistency.
To set this option to the default value, use the default operator with the command.
Configures the OSPF metric for the interface. The switch advertises the metric in
metric
<value> router link advertisements. value is the range 065535. To set this option to the
default value, use the default operator with the command.
poll- Configures the polling interval for the OSPF interface in seconds. seconds is between
interval 12 147 483 647. To set this option to the default value, use the default operator
<seconds> with the command.
Configures the OSPF priority for the interface during the election process for the
designated router. The interface with the highest priority number is the designated
router. The interface with the second-highest priority becomes the backup designated
priority
<value> router. If the priority is 0, the interface cannot become either the designated router or
a backup. The priority is used only during election of the designated router and
backup designated router. value is in the range 0255. The default is 1. To set this
option to the default value, use the default operator with the command.
Configures the retransmit interval for the OSPF interface; the number of seconds
retransmit- between link-state advertisement retransmissions. seconds is an integer between 1
interval
<seconds> 1800. To set this option to the default value, use the default operator with the
command.
Configures the transit delay time for the OSPF interface, the estimated time in
transit- seconds required to transmit a link-state update packet over the interface. seconds is
delay
<seconds> an integer between 11800. To set this option to the default value, use the default
operator with the command.
tunnel-id Specifies the ID number of the tunnel in the range of 12147483647.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 vrrp
ipv6 vrrp
Configure the Virtual Router Redundancy Protocol (VRRP) properties on a port by using the following command.
Syntax
[no] ipv6 vrrp <1-255>
Default
None
Command mode
Interface configuration mode
Command parameters
Parameter Description
<1255> Specifies the Virtual Router ID.
no Delete VRRP from the port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipv6 vrrp address
Syntax
ipv6 vrrp address <1-255> {[global <X:X:X:X:X:X:X:X:>/len] [link-local <fe80::X:X:X:X>}
Default
None
Command mode
Interface configuration mode
Command parameters
Parameter Description
{[global <X:X:X:X:X:X:X:X>/len] [link-local Specifies a global or local-link (or both)
<fe80::X:X:X:X>} IPv6 VRRP address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip verify source interface
Syntax
ip verify source interface [<interface type>] [<portlist>]
Default
None
Command mode
Interface configuration mode
Command parameters
Parameter Description
<interface Identifies the interface on which you want IP Source Guard enabled. Values are
type> FastEthernet and GigabitEthernet.
<portlist> Specifies a single port or range of ports, entered as {slot/port [-slot/port][,...]}.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ipvpn
ipvpn
Create an IP VPN instance in the VRF before you enable the IP VPN for VPN communications.
Syntax
ipvpn
Default
None
Command mode
Global configuration mode
ipvpn enable
Enable IP VPN to configure VPN communications.
Syntax
ipvpn enable
Default
None
Command mode
Global configuration mode
ipvpn service-label-allocation
Configure the service label allocation scheme for locally generated service labels on routes that are exported from a VRF to remote
PEs.
Syntax
ipvpn service-label-allocation {per-vrf|per-vrf-per-nexthop}
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
service- Configures the service label allocation scheme for locally generated service labels on
label- routes that are exported from the VRF to remote PEs. Use per-vrf to enable ingress
allocation VRF IP forwarding information base (FIB) lookup for traffic that arrives from the core
{per- network. This scheme reduces the number of service labels distributed in the VPN
vrf|per- network. Use per-vrf-per-nexthop to enable optimized IP VPN data path at tunnel exit.
vrf-per- This scheme provides higher forwarding throughput than the per-vrf option. To
nexthop} configure this option to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip vrf
ip vrf
Create one or more VRFs for each VPN that the PE node services to isolate the traffic.
Syntax
ip vrf <WORD 0-16>
Default
None
Command mode
VRF router configuration mode
Command parameters
Parameter Description
max-
routes Specifies the maximum number of routes allowed for the VRF from 0250000. To
<0 configure this option to the default value, use the default operator with the command.
250000>
max- Enables the generation of the VRF maximum routes exceeded traps. Use the no operator
routes- to later remove this configuration. To configure this option to the default value, use the
trap
enable default operator with the command.
name
<WORD> Renames the VRF instance.
Enables the generation of the VrfUp and VrfDown traps. Use the no operator to later
vrf-trap
enable remove this configuration. To configure this option to the default value, use the default
operator with the command.
vrfid
<1255> Specifies the VRF instance by number.
<WORD 0-
16> Specifies the name of the VRF instance.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip vrf max-routes
ip vrf max-routes
Configure the maximum number of routes the system can store in the VRF routing table to conserve memory use.
Syntax
ip vrf <vrfName> max-routes <0-250000>
Default
None
Command mode
VRF router configuration mode
Command parameters
Parameter Description
max- Specifies the maximum number of routes allowed for the VRF from the range of 0
routes 250000. To configure this option to the default value, use the default operator with the
<0
250000> command.
vrf
<vrfName> Specifies the VRF name.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ip vrrp
ip vrrp
Configure Virtual Router Redundancy Protocol (VRRP) on a port or a VLAN.
Syntax
ip vrrp <1-255> enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Enables VRRP on the port. Use the no operator to disable VRRP on the port: no ip vrrp
enable <1-255> enable To set this option to the default value, use the default operator with this
command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:i-sid
i-sid
Assigns an ISID to the VRF being configured.
Syntax
[no] [default] i-sid
Default
None
Command mode
VRF configuration mode
Command parameters
Parameter Description
no Use the no option to remove the ISID to VRF allocation for this VRF.
default Use the no option to remove the ISID to VRF allocation for this VRF.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:isis
isis
Create an IS-IS circuit/interface on the selected ports or MLTs.
Syntax
[no] isis
Default
None
Command mode
Interface configuration mode
Command parameters
Parameter Description
[no] Use the no option to delete an IS-IS interface.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:isis apply redistribute
Syntax
isis apply redistribute {direct | bgp| ospf | rip | static}
Default
None
Command mode
IS-IS configuration mode or Global configuration mode
Command parameters
Parameter Description
{direct | bgp| ospf | rip | static} Specifies the protocol.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:isis apply redistribute vrf
Syntax
isis apply redistribute {direct | bgp| ospf | rip | static} vrf <vrf-name>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
{direct | bgp| ospf | rip | static} Specifies the protocol.
vrf <vrf-name> Specifies the VRF. value of WORD 064
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:isis enable
isis enable
Enable the IS-IS circuit/interface on the selected ports or MLTs.
Syntax
[no] [default] isis enable
Default
The default is disabled.
Command mode
Interface configuration mode
Command parameters
Parameter Description
[no] Use the no option to disable SPBM on the specified interface.
[default] Use the default option to disable SPBM on the specified interface.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:isis hello-auth type
Syntax
[no] [default] isis hello-auth type <type> [key <key>] [key-id <key-id>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
no Use the no option to set the hello-auth type to none.
default Use the default option to set the hello-auth type to none.
<type> <type> can be one of the following: none simple: if selected, you can also specifi a key
value. hmac-md5: if selected, you can also specify a key value and key-id.
<key> Specifies a key value.
<key-id> Specifies a key ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:isis l1-dr-priority
isis l1-dr-priority
Configure the level 1 IS-IS designated router priority to the specified value.
Syntax
[no] [default] isis [l1-dr-priority <l1-hello-interval>]
Default
The default value is 64.
Command mode
Global configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value of 64.
default Use the default option to set this parameter to the default value of 64.
<l1-hello-interval Specifies the level 1 IS-IS designated router priority to the specified value.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:isis l1-hello-interval
isis l1-hello-interval
Configure the level 1hello interval.
Syntax
[no] [default] isis l1-hello-interval <l1-hello-interval>
Default
The default is 9.
Command mode
Global configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value of 9 seconds.
default Use the default option to set this parameter to the default value of 9
seconds.
<l1-hello-
interval Specifies the level 1 hello interval.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:isis l1-hello-multiplier
isis l1-hello-multiplier
Configure the level 1 hello multiplier.
Syntax
[no] [default] isis l1-hello-multiplier <l1-hello-multiplier>
Default
The default value is 3 seconds.
Command mode
Global configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value of 3 seconds.
default Use the default option to set this parameter to the default value of 3
seconds.
<l1-hello-
multiplier> Specifies the level 1 hello multiplier.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:isis redistribute
isis redistribute
Configure the redistribution of the specified protocol into the SPBM network.
Syntax
[no] [default] isis redistribute {direct | bgp | ospf | rip | static} [metric <0-65535>]
[metric-type {internal | external}] [route-map <WORD 0-64>] [subnets {allow | suppress}]
Default
None
Command mode
VRF configuration mode
Command parameters
Parameter Description
no Use the no option to delete the configuration.
default Use the default option to delete the configuration.
{direct | bgp | ospf | rip | static} Specifies the protocol.
metric <065535> Specifies metric route.
metric-type {internal | external} Specifies metric-type.
route-map <WORD 064> Specifies route-policy.
subnets {allow | suppress} Specifies subnets.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:isis redistribute enable
Syntax
[no] [default] isis redistribute {direct | bgp | ospf | rip | static} enable
Default
The default is disabled.
Command mode
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:isis spbm
isis spbm
Enable the SPBM instance on the IS-IS interfaces.
Syntax
[no] [default] isis spbm <1-100>
Default
The default is disabled.
Command mode
Interface configuration mode
Command parameters
Parameter Description
[no] Use the no option to disable SPBM on the specified interface.
[default] Use the default option to disable SPBM on the specified interface.
<1100> Enter IS-IS SPBM instance ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:isis spbm interface-type
Syntax
[no] [default] isis spbm <inst> interface-type <if-type>
Default
The default value is 10.
Command mode
Interface configuration mode
Command parameters
Parameter Description
<inst> Specifies the SPBM instance ID.
no Use the no option to set this parameter to the default value of 10.
default Use the default option to set this parameter to the default value of 10.
<if-type> Specifies the interface type.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:isis spbm l1-metric
Syntax
[no] [default] isis spbm <inst> l1-metric <cost>
Default
The default value is 10.
Command mode
Interface configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value of 10.
default Use the default option to set this parameter to the default value of 10.
<inst> Specifies the SPBM instance ID. Range is 1100.
<cost> Specifies the cost. Range is 116777215.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ist enable
ist enable
Enable an interswitch trunk.
Syntax
ist enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the interswitch trunk.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ist peer-ip
ist peer-ip
Create an interswitch trunk from an existing MLT.
Syntax
ist peer-ip <A.B.C.D> vlan <vid>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<A.B.C.D> Specify the peer IP address-the IP address of the IST VLAN on the other aggregation
switch.
<14094> Specify the VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:is-type
is-type
Set the router type globally.
Syntax
[no] [default] is-type {l1}
Default
The default value is l1.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value of l1.
default Use the default option to set this parameter to the default value of l1.
{l1} l1 is a Level-1 router type. l12 is not valid for Release 7.1.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:khi boot-delay
khi boot-delay
Configure the boot delay to provide a valid baseline of normal operations.
Syntax
khi boot-delay <minutes>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<minutes> Specifies the boot delay period in minutes.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:khi chassis
khi chassis
Configure chassis KHI to display the key health indicators of the chassis, including temperature, fans, power supply, slots and CPU
state.
Syntax
khi chassis
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
[no]<14094> Disables the specified KHI feature.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:khi enable
khi enable
Use this command to configure KHI at the global level.
Syntax
[no] khi enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
[no] Disables the specified KHI feature.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:khi performance
khi performance
Use this command to enable performance KHI.
Syntax
[no] khi performance
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
[no] Disables the specified KHI feature.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:khi port
khi port
Enable port KHI to track overall system statistics for the preceding two minutes, Port Up/Down Events, SMLT Port Up/Down
Events, IST Port Up/Down Events, IST Port Up/Down Events, Port Errors and the history of the last 10 Port KHI events.
Syntax
[no] khi port
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
no Disables the specified KHI feature.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:l2 ping
l2 ping
Trigger an L2 ping.
Syntax
l2 ping l2 ping {vlan <vlan> routernodename <RouterNodeName> | vlan <vlan> systemidmac
<SystemIdMac> | ip-address <ipaddress>} [burst-count <value>] [data-tlv-size <value>]
[frame-size <value>] [testfill-pattern <value>] [priority <value>] [time-out <value>]
[source-mode <value>] [vrf <value>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vlan <vlan> routernodename Specifies the destination for the L2 ping: <vid> = <1
<RouterNodeName> | vlan <vlan> 4094> <.RouterNodeName> = Word <0255>
systemidmac <SystemIdMac> | ip- <SystemIDMac> = <XX:XX:XX:XX:XX:XX>
address <ipaddress> <ipaddress> = <A.B.C.D>
burst-count <value> Specifies the burst count. Range is 1200.
data-tlv-size <value> Specifies the data TLV size. Range is 0400.
frame-size <value> Specifies the frame size. Range is 64500.
Specifies the testfill pattern. Range is 14:all-zero all-
testfill-pattern <value> zero-crc pseudo-random-bit-sequence pseudo-random-
bit-sequence-crc
priority <value> Specifies the priority. Range is 07.
time-out <value> Specifies the interval in seconds. Range is 110.
source-mode <value> Specifies the source mode. Range is 12:nodal
smltVirtual
vrf <value> Specifies the VRF name.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:l2tracemroute source group
cvlan
Syntax
l2tracemroute source <ip address> group <ip address> cvlan <value> priority <value> ttl
<value>
Default
None
Command mode
User EXEC mode
Command parameters
Parameter Description
source <ip
address> Specifies the IP address where the trace m route originates from.
group <ip
address> Specifies the IP address of the C-VLAN group.
cvlan
<value> Specifies the C-VLAN to associate with the I-SID. The range is between 0 and 4,094.
priority Specifies the priority value to be used in the C-VLAN header if present in the
<value> transmitted frame. The value is between 0 and 7.
ttl <value> Specifies the returned trace response. The TTL value is between 1 and 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:l2tracemroute source group
vrf priority ttl
Syntax
l2tracemroute source <ip address> group <ip address> vrf <value> priority <value> ttl
<value>
Default
None
Command mode
User EXEC mode
Command parameters
Parameter Description
source <ip
address> Specifies the IP address where the trace m route originates from.
group <ip
address> Specifies the IP address of the VRF group.
vrf <value> Specifies the VRF to associate with the I-SID. The range is between 0 and 64.
priority Specifies the priority value to be used in the VRF header if present in the
<value> transmitted frame. The value is between 0 and 7.
ttl <value> Specifies the returned trace response. The TTL value is between 1 and 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:l2 traceroute
l2 traceroute
Trigger an L2 traceroute.
Syntax
l2 traceroute {vlan <vid> routernodename <RouterNodeName> | vlan <vid> systemidmac
<SystemIdMac> | <ipaddress>} [ttl <value>] [priority <value>] [source-mode <value>] [vrf
<value>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vlan <vid> Specifies the destination for the L2 traceroute:<vid> =
routernodename<RouterNodeName> <14094> <RouterNodeName> = Word <0255>
| vlan <vid> systemidmac <SystemIDMac> = <XX:XX:XX:XX:XX:XX> <ipaddress> =
<SystemIdMac> | <ipaddress> <A.B.C.D>
ttl <value> Specifies the TTL value. Range is 1255.
priority <value> Specifies the priority. Range is 07.
source-mode <value> Specifies the source mode. Range is 12.nodal smltVirtual
vrf <value> Specifies the VRF name.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:l2 tracetree
l2 tracetree
Trigger an L2 tracetree.
Syntax
l2 tracetree {<vlan.isid> | <vid.isid.RouterNodeName> | <vlan.isid.SystemIdMac>} [ttl
<value>] [priority <value>] [source-mode <value>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<vlan.isid> | {{1..4094}.{1..16777215}} | {{1..4094}. {1..16777215}.str}
<vid.isid.RouterNodeName> | | {{1..4094}.{1..16777215}.
<vlan.isid.SystemIdMac> {00:00:00:00:00:00...FF:FF:FF:FF:FF:FF}}
ttl <value> Specifies the TTL value. Range is 1255.
priority <value> Specifies the priority value. Range is 07.
source-mode <value> Specifies the source mode. Range is 12:1: nodal 2:
smltVirtual
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:lacp
lacp
Configure LACP parameters globally. When the LACP system priority is set globally, it applies to all LACP-enabled aggregators and
ports.
Syntax
lacp
Default
The default is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
aggr-wait-time <2002000> Sets the aggregation wait time (in milliseconds) globally.
The default value is 2000.
Enables LACP globally. To disable LACP globally, use the no
enable operator to remove this configuration. To set this option to
the default value, use the default operator with the
command.
fast-periodic-time <20020000> Sets the fast-periodic time (in milliseconds) globally. The
default is 20000 ms.
slow-periodic-time <10000 Sets the slow periodic time globally. The default value is
30000> 1000 ms.
smlt-sys-id Sets the LACP system ID globally. Enter a MAC address in
<0x00:0x00:0x00:0x00:0x00:0x00> the following format: 0x00:0x00:0x00:0x00:0x00:0x00.
system-priority <0-65535> Sets the global LACP system priority. The default value is
32768.
Sets the timeout scale globally. The default value is 3. To
timeout-scale <2-10> set this option to the default value, use the default
operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:lacp enable
lacp enable
Configure LACP on a port to enable or disable LACP on the selected ports.
Syntax
lacp enable
Default
The default is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables LACP on the port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:lacp enable key
Syntax
lacp enable key <integer>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
key <integer> Sets LACP aggregator key for a specific MLT. integer is the LACP actor admin key.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:lb-controller
lb-controller
Specifies the ID of the WLAN Controller that you want to add or remove from the cluster of WLAN Controllers. The valid numbers
are from 1 to 4.
Syntax
lb-controller <contId:1-4>
Default
None
Command mode
WLAN Switch Configuration
Command parameters
Parameter Description
<contId:1 Specifies the ID of the WLAN Controller that you want to add or remove from the
4> cluster of WLAN Controllers. The valid numbers are from 1 to 4.
<A.B.C.D> Specifies the IPv4 address of the WLAN Controller, which must be a unique address
within the WLAN domain.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:link-flap-detect auto-port-
down
link-flap-detect auto-port-down
Enable automatic port disabling.
Syntax
link-flap-detect auto-port-down
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
auto- Activates automatic disabling of the port if the link-flap threshold is exceeded. This option
port- is disabled by default. Use the no operator to remove this configuration. To set this
down option to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:link-flap-detect frequency
link-flap-detect frequency
Configure the number of changes allowed during the interval on the port.
Syntax
link-flap-detect frequency <frequency>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Configures the number of changes that are allowed during the time specified by the
frequency
<frequency> interval command. The default is 10. frequency is from 19999. To set this option to
the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:link-flap-detect interval
link-flap-detect interval
Configure link flap detection and interval to control link state changes on a physical port.
Syntax
link-flap-detect interval <interval>
Default
The default is 60.
Command mode
Global configuration mode
Command parameters
Parameter Description
interval Configures the link-flap-detect interval in seconds. interval is from 2600. To set this
<interval> option to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:link-flap-detect send-trap
link-flap-detect send-trap
Enable sending a trap on the port.
Syntax
link-flap-detect send-trap
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Activates sending traps. The default is activated. Use the no operator to remove this
send-
trap configuration. To set this option to the default value, use the default operator with the
command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:linktrace
linktrace
Trigger a linktrace.
Syntax
linktrace <md-name> <ma-name> <mepID> <rmepMac> [detail] [priority <value>] [source-mode
<value>] [ttl-value <value>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<md-name> Specifies the MD name in a string of 122 characters.
<ma-name> Specifies the MA name in a string of 122 characters.
<mepID> Specifies the MEP ID. Range is 18191.
<rmepMac> Specifies the remote MAC address to reach the MEP. Range is 00:00:00:00:00:00
- FF:FF:FF:FF:FF:FF.
detail Displays linktrace result details.
priority
<value> Specifies the priority. Range is 07.
source-mode
<value> Specifies the source mode. Range is 1 2:nodal smltVirtual
ttl-value
<value> Specifies the ttl value. Range is 1 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:load-encryption-module
load-encryption-module
Load the appropriate SNMPv3 encryption module before you can use SNMPv3 with Data Encryption Standard (DES) or Advanced
Encryption Standard (AES) to access the device.
Syntax
load-encryption-module <DES|AES>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
DES|AES Specify the SNMPv3 encryption module to load: AES or DES.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:load-license
load-license
Load the license file to unlock the licensed features.
Syntax
load-license
Default
None
Command mode
Global configuration mode
lock port
Lock a port to prevent other users from changing port parameters or modifying port action.
Syntax
lock port {slot/port[-slot/port][,...]} enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
port Specifies the slot and the port number to be locked.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:logging
logging
Configure log file parameters, as well as write, or clear the log file automatically created by the system.
Syntax
logging level <0-4>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Shows and sets the logging level. The level is one of these values: 0 = Information; all
messages are recorded. 1 = Warning; only warning and more serious messages are
level
<0-4> recorded. 2 = Error; only error and more serious messages are recorded. 3 =
Manufacturing; this parameter is not available for customer use. 4 = Fatal; only fatal
messages are recorded.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:logging logToPCMCIA
logging logToPCMCIA
Begin or stop logging system messages to the PCMCIA card.
Syntax
logging logToPCMCIA
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
no Stops the logging system messages.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:logging transferfile
logging transferfile
Configure the remote host address for log transfer. The system transfers the current log file to a remote host when the log file
size reaches the configured maximum size.
Syntax
logging transferFile <1-10> address <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
address Specifies the IP address of the host to where the log file needs to be transferred. The
<A.B.C.D> remote host must be reachable or the configuration will fail.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:login-message
login-message
Change the login prompt to configure the run-time environment and define the generic configuration settings for ACLI sessions.
Syntax
login-message <string>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Changes the ACLI logon prompt. string is an (American Standard Code for Information
login- Interchange) (ASCII) string from 11513 characters. Use the default option before this
message parameter, default loginmessage, to enable using the default logon string. Use the no
<string> operator before this parameter, no loginmessage, to disable the default logon banner and
display the new banner.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:loopback
loopback
Trigger a loopback test.
Syntax
loopback <md-name> <ma-name> <mepID> <rmepMac> [burst-count <value>] [data-tlv-size
<value>] [frame-size <value>] [priority <value>] [source-mode <value>] [testfill-pattern
<value>] [time-out <value>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<md-name> Specifies the MD name in a string of 122 characters.
<ma-name> Specifies the MA name in a string of 122 characters.
<mepID> Specifies the MEP ID. Range is 18191.
<rmepMac> Specifies the remote MAC address to reach the MEP/ MIP. Range is
00:00:00:00:00:00 - FF:FF:FF:FF:FF:FF.
burst-count
<value> Specifies the burst-count. Range is 1200.
data-tlv-size
<value> Specifies the data TLV size. Range is 0 400.
frame-size
<value> Specifies the frame-size. Range is 64500.
priority
<value> Specifies the priority. Range is 0 7.
source-mode
<value> Specifies the source mode. Range is 12:nodal smltVirtual
testfill- Specifies the testfill pattern. Range is 1-4:all-zero all-zero-crc pseudo-random-
pattern <value> bit-sequence pseudo-random-bit-sequence-crc
time-out
<value> Specifies the timeout interval in seconds. Range is 1 10.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:loop-detect action
loop-detect action
Configure the ARP loop detection when loop-detect is enabled.
Syntax
loop-detect [action {port-down|vlan-block|mac-discard}] [arp-detect]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
action Indicates the action that the switch takes: port-down|vlan-block|mac-discard.
arp-detect -
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:loop-detect arp-detect
loop-detect arp-detect
Configure the Loop Detection to detect the MAC addresses that are looping from one port to another port.
Syntax
loop-detect arp-detect
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
action Specifies the loop detect action to be taken.
arp- The Address Resolution Protocol (ARP)-Detect feature is used for IP configured interfaces
detect for ARP packets. Enable this feature (in addition to loop detection) on routed interfaces.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mac-security auto-learning
mac-security auto-learning
Configure FDB protection on ports to manage network performance.
Syntax
mac-security auto-learning fdbprotect
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
fdbprotect Enables fdbprotect on the port.
fdb-protect Enable or disable MAC address learning on the specified ports.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:manual-area
manual-area
Configure an IS-IS manual area (113 bytes in the format <xx.xxxx.xxxx...xxxx>. In this release, only one manual area is
supported.
Syntax
[no] manual-area <area>
Default
None
Command mode
Router IS-IS configuration mode
Command parameters
Parameter Description
[no] Deletes the specified IS-IS manual area.
<area> <area>is 113 bytes in the format xx.xxxx.xxxx...xxxx>
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:match extended-prefix
match extended-prefix
Associate an extended ACL with the route policy.
Syntax
match extended-prefix Word<1-255>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Word <1
255> Specifies the name of the extended ACL to associate with the route policy.
no Clears the association between the route policy and the extended ACL when prefixed
with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:max-logins
max-logins
Configure the number of supported rlogin sessions to define the generic configuration settings for ACLI sessions.
Syntax
max-logins <nsessions>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
max-logins Configures the allowable number of inbound remote ACLI logon sessions; the
<nsessions> default is 8. nsessions is the number of sessions (08).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:max-lsp-gen-interval
max-lsp-gen-interval
Specify the maximum interval, in seconds, between generated LSPs by this Intermediate system. The value must be greater than
any value configured for min-lsp-gen-interval.
Syntax
[no] [default] max-lsp-gen-interval <max-lsp-interval>
Default
The default value is 900 seconds.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value of 900 seconds.
default Use the default option to set this parameter to the default of 900 seconds.
<max-lsp- Specifies the maximum interval, in seconds, between generated LSPs. Range is
interval> 0900.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:md5 filename
md5 filename
Use the MD5 checksums to ensure the integrity of the new software files before you use them to upgrade. Corrupted files can
cause the upgrade to fail.
Syntax
md5 <filename> [-a] [-c] [-f] [-r]
Default
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
-a Adds data to the output file instead of overwriting it. You cannot use the -a option with
the -c option.
Compares the checksum of the specified file by <filename> with the MD5 checksum
present in the checksum file name. You can specify the checksum file name using the -f
option. When the checksum file name is not specified, the file /flash/checksum.md5 is
-c used for comparison. If the checksum file name and the default file are not available in
flash memory, the following error message is displayed: Error: Checksum file
<filename> not present. The -c option also: calculates the checksum of files specified
by filename compares the checksum with all keys in the checksum file, even if the file
names do not match shows the results of the comparison
Stores the result of MD5 checksum to a file in flash memory or on a PCMCIA card. If
the output file specified with the -f option is one of the: reserved file names on the
-f switch, the command fails and the error message is displayed: Error: Invalid operation.
<checksum- files for which MD5 checksum is to be computed, the command fails and the error
file- message is displayed: Error: Invalid operation on file <filename> If the checksum file
name> name specified by the -f option already exists on the switch (and is not one of the
reserved file names), the following message is shown: File exists. Do you wish to
overwrite? (y/n)
-r Reverses the output and can be used with -f option to store the output to a file. The -r
option cannot be used with the -c option.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:metric
metric
Specify the IS-IS metric type.
Syntax
[no] [default] metric {wide}
Default
The default is wide.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value of wide.
default Use the default option to set this parameter to the default of wide.
{wide} Specifies the IS-IS metric type. Only wide is supported in Release 7.1.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mgmt-ip
mgmt-ip
Sets the WSP management interface IP address.
Syntax
mgmt-ip <A.B.C.D>
Default
None
Command mode
WLAN Switch Configuration
Command parameters
Parameter Description
<A.B.C.D> Sets the WSP management interface IP address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:min-lsp-gen-interval
min-lsp-gen-interval
Specify the minimum time between successive generation of LSPs with the same LSPID. This is a system level parameter that
applies to both L1 and L2 LSP generation.
Syntax
[no] [default] min-lsp-gen-interval <min-lsp-interval>
Default
The default value is 30 seconds.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value of 30.
default Use the default option to set this parameter to the default of 30.
<min-lsp- Specifies the minimum time between successive generation of LSPs with the same
interval> LSPID. Range is 165535.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mirror-by-port
mirror-by-port
Use port mirroring to aid in diagnostic and security operations.
Syntax
mirror-by-port <1-383> in-port <portList> {monitor-mlt <1-256>|monitor-vlan <1-4094>|out-
port <portList>}
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
in-port <portList> Creates a new mirror-by-port table entry. in-port <portList> specifies
{monitor-mlt <1- the mirrored port. monitor-mlt <1-256> specifies the mirroring MLT ID
256>|monitor-vlan
<1-4094>|out-port from 1 to 256. monitor-vlan <1-4094> specifies the mirroring VLAN ID
<portList>} from 1 to 4094. out-port <portList> specifies the mirroring port.
<1-383> Specifies the mirror-by-port entry ID in the range of 1 to 383.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mlt
mlt
Configure an MLT to set up MLTs on the switch.
Syntax
mlt <mlt ID>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Creates and enables a new MLT.
encapsulation dot1q Sets encapsulation. dot1q enables trunking on the MLT.
member <portList> Adds ports to this MLT.
<mlt ID> Specifies the MLT ID in the range of 1256.
name <0-20> Changes the name for this MLT in the range of 020 characters.
ntstg enable Enables NTSTG.
vlan <14094> Specifies a VLAN ID to add to this MLT.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mlt member
mlt member
Add ports to an MLT LAG to add an existing VLAN to a link aggregation configuration.
Syntax
mlt <1-256> member <portlist> vlan <1-4094>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-256> Specifies the MLT ID in the range of 1 to 256.
<portList> Specifies the port and the slot number.
vlan <1-4094> Specifies the VLAN ID in the range of 1 to 4094.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:more boot.cfg
more boot.cfg
View configuration file information.
Syntax
more boot.cfg
Default
None
Command mode
Privileged EXEC mode
Syntax
mpls ldp
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
ldp Enables LDP on the interface. The default is disabled. The default operator is default mpls
ldp. The no operator is no mpls ldp.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mpls ldp globally
Syntax
mpls ldp
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
The Ethernet Routing Switch 8800/8600 is the egress router for connected routes that
egress- are advertised into LDP. This setting determines how those prefixes are redistributed.
policy After redist-connected is enabled, the router acts as the egress router for all connected
redist- routes. After redist-connected is disabled, the router acts as the egress router for
connected loopback addresses only. The default is disabled. The default operator is default mpls
rsvp message-bundling. The no operator is no mpls rsvp message-bundling.
Defines how LDP supports penultimate hop popping (PHP). The default is implicit-null.
implicit-null causes the upstream LSR to pop the label stack if it is the penultimate (next-
to-last) hop in the MPLS network. explicit-null causes the upstream LSR to treat this
label value like a normal label before sending the packet to the egress router. However,
explicit- when the egress router receives a packet with this label, it automatically pops off the
null label stack entry and classifies and forwards the packet based on the next inner label. If
there is no inner label, it uses the encapsulated packet header. Important All LDP
sessions restart after you change this setting, and the new value takes effect
immediately. The default operator is default mpls ldp explicit-null. The no operator is no
mpls ldp explicit-null.
Specifies the interval (in seconds) that the system remembers an LDP neighbor without
receiving a Hello message. The timer restarts to this value whenever the system receives
hello- a Hello message from a peer. If the timer expires before another Hello message is
holdtime
<5- received, the system terminates the Hello adjacency. Changes to this setting do not
65535> affect existing LDP sessions. The interval range is a number of seconds between 5
65535. The default is 15. The default operator is default mpls ldp hello-holdtime. A value
of zero (0) indicates that the hello-holdtime variable is the global indicator.
holdtime Specifies the interval (in seconds) between LDP keep alive messages sent to neighbors
<15- or interfaces. The allowed range is 152147483. The default is 15. The default operator
2147483> is default mpls ldp holdtime.
Specifies the maximum number of hops permitted in a Label Request message. The
loop- router assumes the path is a loop if the hop count parameter exceeds this value. Then
detection the router does not respond with a Label Mapping message, and it does not propagate
max-hops the Label Request. Changes to this setting do not affect existing LDP sessions. The
<1-255> default is 0. The default operator is default mpls ldp loop-detection max-hops. The no
operator is no mpls ldp loop-detection max-hops.
Specifies the maximum path vector length permitted in a Label Request message. The
loop- router assumes the path is a loop if the vector length is equal to or greater than this
detection value (or if the router LSR ID is present in the path vector. Then the router does not
path- respond with a Label Mapping message, and it does not propagate the Label Request.
vector Changes to this setting do not affect existing LDP sessions. The default is 0. The default
<1-255> operator is default mpls ldp loop-detection path-vector. The no operator is no mpls ldp
loop-detection path-vector.
traps Sets an SNMP trap when paths meet or exceed the path vector limit. The default is no
path-
vector mpls ldp traps path-vector (disable).
Sets an SNMP trap when an LDP status changes. The default is disabled (no). The
traps
status default operator is default mpls ldp traps status. The no operator is no mpls ldp traps
status.
Sets an SNMP trap when the session exceeds the threshold. The default is disabled (no).
traps
threshold The default operator is default mpls ldp traps threshold. The no operator is no mpls ldp
traps threshold.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mpls ldp vlan
Syntax
mpls ldp
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
ldp Enables LDP on the VLAN. The default operator is default mpls ldp. The no operator is no
mpls ldp.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mpls router-id
mpls router-id
Configure the MPLS router ID on the switch to globally enable the Label Distribution Protocol (LDP) and the Resource Reservation
Protocol (RSVP).
Syntax
mpls router-id <A.B.C.D>
Default
None
Command mode
Global configuration mode
Syntax
mpls rsvp
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
hello-
interval Configures the RSVP hello interval (in seconds). The default operator is default mpls
{global|<1- rsvp hello-interval 10.
65535>}
message- Bundles messages from different interfaces that are going to the same final
bundling destination. The default operator is default mpls rsvp message-bundling global. The
[global] no operator is no mpls rsvp message-bundling.
Sets the maximum transmission size of frames for this MPLS interface. The supported
mtu <64-
9600> options are 1950, 9600, and 1500. However, the MPLS MTU value cannot exceed that
of the system MTU size. The default operator is default mpls mtu 1500.
refresh
interval Configures the RSVP refresh interval (in seconds). The default operator is default mpls
{global|<1- rsvp refresh interval 30.
65535>}
refresh Configures the refresh multiplier (in seconds). After the node receives a ResvErr
multiplier message, this value multiplied times the refresh interval determines how long to set
{global|<1- the blockade timer. (For more information, see RFC 2205.) The default operator is
255>} default mpls rsvp refresh multiplier 3.
refresh Configures whether or not to send RSVP summary refresh messages. The default
reduction operator is default mpls rsvp refresh reduction. The no operator is no mpls rsvp
[global] refresh reduction.
rsvp Configures RSVP on this interface. The default operator is default mpls rsvp. The no
operator is no mpls rsvp.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mpls rsvp explicit-path
Syntax
mpls rsvp explicit-path <WORD 0-32> hop <1-255>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Defines the hops in the explicit path. Enter a hop index and address to create an entry in
the hop table. The IP address must be an IP/MPLS interface on the router, not the LSR-
hop <1-
255> ID.<1-255> specifies the index value assigned to this hop. The index determines the
order of the hop in the list of configured hops (lower to higher). For example, the path
goes to hop 1 and then hop 2.
Word<0-
32> Specifies the explicit path name with a string length of 0 to 32 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mpls rsvp globally
Syntax
mpls rsvp
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Defines how RSVP supports penultimate hop popping (PHP). implicit-null causes the
upstream LSR to pop the label stack if it is the penultimate (next-to-last) hop in the
MPLS network. explicit-null causes the upstream LSR to treat this label value like a
explicit- normal label before sending the packet to the egress router. However, when the
null egress router receives a packet with this label, it automatically pops off the label stack
entry and classifies and forwards the packet based on the next inner label. If there is
no inner label, it uses the encapsulated packet header. Important All RSVP sessions
restart after you change this setting, and the new value takes effect immediately.
explicit-
path <WORD Configures the RSVP explicit-path settings.
0-32>
hello- Configures the RSVP hello interval (in seconds). The range is from 065535. When set
interval
<0-65535> to 0, no hellos are sent. The default operator is default mpls rsvp hello-interval 10.
lsp <WORD
0-32> Configures the RSVP LSP configurations.
Bundles messages from different interfaces that are going to the same final
message-
bundling destination. The default operator is default mpls rsvp message-bundling. The no
operator is no mpls rsvp message-bundling.
refresh Configures the RSVP refresh interval (in seconds). The range is from 1 to 65535. The
interval
<1-65535> default operator is default mpls rsvp refresh interval 30.
Configures the refresh multiplier (in seconds). When the node receives a ResvErr
refresh message, this value multiplied times the refresh interval determines how long to set
multiplier
<1-255> the blockade timer. (For more information, see RFC 2205.) The range of values is from
1255. The default operator is default mpls rsvp refresh multiplier 3.
Configures whether or not to send RSVP summary refresh messages. The default
refresh
reduction operator is default mpls rsvp refresh reduction. The no operator is no mpls rsvp
refresh reduction.
resource Configures the RSVP resource.
<1-255>
static-ip
<A.B.C.D/X> Configures the RSVP static-IP address.
Configures whether or not to send trap messages when RSVP LSPs change their state.
traps
tunnel The default operator is default mpls rsvp traps tunnel. The no operator is no mpls rsvp
traps tunnel.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mpls rsvp lsp
Syntax
mpls rsvp lsp <WORD 0-32>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
lsp <WORD Names the LSP with a string from 0 to 32 characters. The default operator is default
0-32> mpls rsvp lsp <WORD 0-32>.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mpls rsvp lsp primary
Syntax
mpls rsvp lsp <WORD 0-32> primary
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the value of the LSP resource index, which determines how much bandwidth
bandwidth
<0-255> the primary LSP can use. The range of values for the index is from 0 to 255. A value of 0
indicates that this LSP uses a best effort approach.
enable Enable brings up the primary LSP; the no operator for enable brings down the LSP.
explicit-
path Specifies the name of an explicit path for this primary LSP to use.
<WORD 0-
32>
record- Configures whether or not RSVP can make a retain a record of this LSP after it is
route signaled.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mpls rsvp resource
Syntax
mpls rsvp resource <1-255> <0-2147483647>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
resource <1- Globally configures an MPLS RSVP resource on the switch. Specify the LSP resource
255> <0- index by entering a value from 1 to 255. Specify the bandwidth (in Kbps) by
2147483647> entering a value from 0 to 2147483647.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mpls rsvp static-ip
Syntax
mpls rsvp static-ip <ipaddr/mask> lsp <name>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
static-ip Creates a static path by specifying an IP address and mask and naming the LSP.
<A.B.C.D/0-32> The default operator is default mpls rsvp static-ip <A.B.C.D/0-32>. The no
lsp <WORD 0-
32> operator is no mpls rsvp static-ip <A.B.C.D/0-32>.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mpls rsvp vlan
Syntax
mpls rsvp
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
hello-
interval Configures the RSVP hello interval (in seconds). The default operator is default mpls
{global|<1- rsvp hello-interval 10.
65535>}
message- Bundles messages from different interfaces that are going to the same final
bundling destination. The default operator is default mpls rsvp message-bundling global. The
[global] no operator is no mpls rsvp message-bundling.
Sets the maximum transmission size of frames for this MPLS VLAN. The supported
mtu <64-
9600> options are 1950, 9600, and 1500. However, the MPLS MTU value cannot exceed that
of the system MTU size. The default operator is default mpls mtu 1500.
refresh
interval Configures the RSVP refresh interval (in seconds). The default operator is default mpls
{global|<1- rsvp refresh interval 30.
65535>}
refresh Configures the refresh multiplier (in seconds). After the node receives a ResvErr
multiplier message, this value multiplied times the refresh interval determines how long to set
{global|<1- the blockade timer. (For more information, see RFC 2205.) The default operator is
255>} default mpls rsvp refresh multiplier 3.
refresh Configures whether or not to send RSVP summary refresh messages. The default
reduction operator is default mpls rsvp refresh reduction. The no operator is no mpls rsvp
[global] refresh reduction.
rsvp Configures RSVP on this VLAN. The default operator is default mpls rsvp. The no
operator is no mpls rsvp.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mpls statistics receive
Syntax
mpls statistics receive
Default
None
Command mode
Global configuration mode
Syntax
mpls statistics receive start-label<0-1048575>
Default
None
Command mode
Global configuration mode
Syntax
mpls statistics transmit
Default
None
Command mode
Privileged EXEC mode
Syntax
mpls statistics transmit start-label<0-1048575>
Default
None
Command mode
Privileged EXEC mode
multicast enable
Use this command to turn on IP multicast over SPBM.
Syntax
<spbm|no spbm> <instance> multicast enable
Default
Default range for IS-IS is 16,000,000 to 16,512,000
Command mode
Router IS-IS configuration mode
Command parameters
Parameter Description
spbm | no spbm Enables or disables IP multicast over SPBM.
instance Specifies the SPBM instance (1 to 100). In this release, one instance is supported.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:multicast fwd-cache-timeout
multicast fwd-cache-timeout
Use this command to configure the timeout value on the GRT.
Syntax
<spbm | no spbm> <1-100> multicast fwd-cache-timeout <fwd-cache-timeout>
Default
None
Command mode
Router IS-IS configuration mode
Command parameters
Parameter Description
spbm | no spbm Enables or disables the timeout value on the GRT.
instance Specifies the SPBM instance (1 to 100. In this release, one instance is
supported.
fwd-cache- Specifies when the timeout interval in seconds. The range is between 10 to
timeout 86400 seconds.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:multicast mlt-distribution
enable
Syntax
multicast mlt-distribution
Default
None
Command mode
Global configuration mode
Syntax
multicast mlt-distribution [grp-mask <grp-mask>] [redistribution] [src-mask <src-mask>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies a group mask to use when the switch distributes multicast traffic over a
grp-mask multilink trunk. The default is 255.255.255.255. To set this option to the default
<grp-mask> value, use the default operator with the command. You must disable MLT
distribution before you change the group mask.
Enables the multicast MLT redistribution feature. The default is disabled. Use the
redistribution no operator to later remove this configuration. To set this option to the default
value, use the default operator with the command.
Specifies a source mask to use when the switch distributes multicast traffic over a
src-mask multilink trunk. The default is 255.255.255.255. Important Ensure that the mask
<src-mask> values for grp-mask and src-mask are contiguous. To set this option to the
default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:multicast mlt-distribution
multilink trunk
Syntax
multicast mlt-distribution [grp-mask <grp-mask>] [redistribution] [src-mask <src-mask>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies a group mask to use when the switch distributes multicast traffic over a
grp-mask multilink trunk. The default is 255.255.255.255. To set this option to the default
<grp-mask> value, use the default operator with the command. You must disable MLT
distribution before you change the group mask.
Enables the multicast MLT redistribution feature. The default is disabled. Use the
redistribution no operator to later remove this configuration. To set this option to the default
value, use the default operator with the command.
Specifies a source mask to use when the switch distributes multicast traffic over a
src-mask multilink trunk. The default is 255.255.255.255. Important Ensure that the mask
<src-mask> values for grp-mask and src-mask are contiguous. To set this option to the
default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:multicast smlt-square
multicast smlt-square
Enable square-SMLT globally on each of the four switches to form an SMLT aggregation group.
Syntax
multicast smlt-square
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
smlt-square Enables multicast SMLT square.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:multicast software-
forwarding
multicast software-forwarding
Configure the IP multicast software forwarding feature so the SF/CPU initially forwards IP multicast data until a hardware record is
created.
Syntax
multicast software-forwarding
Default
None
Command mode
Global configuration mode
mvpn enable
Use this command to enable layer 3 VSN SPBM services for a particular VRF.
Syntax
<mvpn|no mvpn> enable
Default
Enabled
Command mode
VRF router configuration mode
Command parameters
Parameter Description
mvpn | no mvpn Enables or disables IP multicast over SPBM for a particular VRF.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:mvpn fwd-cache-timeout
mvpn fwd-cache-timeout
Use this command to configure the timeout value on the VRF.
Syntax
<mvpn | np mvpn> fwd-cache-timeout <fwd-cache-timeout>
Default
None
Command mode
Router IS-IS configuration mode
Command parameters
Parameter Description
mvpn | no mvpn Enables or disables the timeout value on the VRF/
fwd-cache- Specifies when the timeout interval in seconds. The range is between 10 to
timeout 86400 seconds.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:name port
name port
Specify the name of the port that needs to be changed and have same settings for all the ports.
Syntax
name [port <portList>] <WORD 0-42>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
portlist Specifies the slot and the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:neighbor
neighbor
Configure NBMA neighbors so that the interface can participate in Designated Router election. All OSPF neighbors that you
manually configure are NBMA neighbors.
Syntax
neighbor <A.B.C.D> [priority <0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<A.B.C.D> Identifies an OSPF area in IP address format a.b.c.d.
priority <0-255> Changes the priority level of the neighbor.
<nbr_ipaddr|peer-
group-name> Indicates that you enter the peer's IP address or the peer's group name.
Specifies one or more mask choices that you enter, separated by commas
mask <WORD 1- with no space between choices. For example, [<mask>,<mask>,<mask>...].
100> Options include: none, all, error, packet, event, trace, warning, state, init,
filter, update.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:neighbor a.b.c.d fall-over
bfd
Syntax
neighbor {<A.B.C.D>}|ipv6addr <WORD 0-1536>} fall-over bfd
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
fall-over bfd Sets the fall over status of BFD.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:neighbor address-family
vpnv4
Syntax
neighbor <nbr_ipaddr|peer-group-name> address-family vpnv4
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Configures BGP address families for IPv4 (BGP) and Layer 3 VPN (MP-BGP)
address-family support. Enable for VPN/VRF routes. Use the no operator to later remove this
vpnv4 configuration. To configure this option to the default value, use the default
operator with the command.
<nbr_ipaddr|peer- Specifies the properties of a statically configured peer within a BGP group.
group-name> Enter the neighbor IP address in a.b.c.d format for <nbr_ipaddr>, or the
neighbor group name for <peer-group-name>.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:neighbor-debug-all
neighbor-debug-all
Displays specified debug information for BGP neighbors.
Syntax
neighbor-debug-all mask <WORD 1-100>
Default
The default value is none.
Command mode
Global configuration mode
Command parameters
Parameter Description
mask <WORD 1- <WORD 1-100> is a list of mask choices separated by commas with no space
100> between choices.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:neighbor-debug-all mask
neighbor-debug-all mask
Display specific debug messages for your global BGP neighbors
Syntax
neighbor-debug-all mask <WORD 1-100>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
mask Specifies one or more mask choices that you enter, separated by commas with no space
<WORD 1- between choices. For example, [<mask>,<mask>,<mask>...]. Options include: none, all,
100> error, packet, event, trace, warning, state, init, filter, update.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:neighbor ipaddress
neighbor ipaddress
Use peers and peer groups to simplify BGP configuration and makes updates more efficient.
Syntax
neighbor <nbr_ipaddr|peer-group-name> address-family vpnv4
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Enables BGP address families for IPv4 (BGP) and L3 VPN (MP-BGP) support. Enable this
address- parameter for VPN/VRF Lite routes. The no form of this command is no neighbor
family
vpnv4 <nbr_ipaddr|peer-group-name> address-family vpnv4. The default form of this command
is default neighbor <nbr_ipaddr|peer-group-name> address-family vpnv4.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:neighbor ipvpn-lite-
capability
neighbor ipvpn-lite-capability
Enable IP VPN-Lite to provide IP VPN in a routed network without explicit tunnels between PE devices.
Syntax
neighbor <nbr_ipaddr|peer-group-name> ipvpn-lite-capability
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the properties of a statically configured peer within a BGP group.
<nbr_ipaddr|peer-
group-name> Enter the neighbor IP address in a.b.c.d format for <nbr_ipaddr>, or the
neighbor group name for <peer-group-name>.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:net6-mgmt ipv6
net6-mgmt ipv6
Assign IPv6 addresses to the management port to manage the device.
Syntax
net6-mgmt ipv6 <IPv6 address/prefix length>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
IPv6 address/prefix Specifies the IPv6 address and prefix length to assign to the
length management interface.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:net6-mgmt ipv6 route
Syntax
net6-mgmt ipv6 route <network IPv6 address>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
network IPv6 address Specifies the IPv6 address and prefix length of the network to add.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:network
network
Specify the IGP network prefixes for BGP to advertise for redistribution.
Syntax
network <prefix/len> [metric <0-65535>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
network Specifies IGP network prefixes for BGP to advertise for redistribution. This command
<prefix/len> imports routes into BGP.<prefix/len> is the network address and mask. metric <0-
metric <0-
65535> 65535> corresponds to the MED (multiexit discriminator) BGP attribute for the route.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:nlb-mode unicast
nlb-mode unicast
Configure the NLB unicast support on an IP interface to enable or disable the Network Load Balancer (NLB) unicast support.
Syntax
nlb-mode unicast
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
igmp-mcast Sets nlb-mode to igmp-mcast.
multicast Sets nlb-mode to multicast.
unicast Sets nlb-mode to unicast.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:no access-diffserve enable
no access-diffserve enable
Configure a port as trusted to determine the Layer 3 QoS actions the switch performs. A trusted port honors incoming DSCP
markings.
Syntax
no access-diffserve enable
Default
The default is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
enable If enabled, specifies an access port and overrides incoming DSCP bits. If disabled,
specifies a core port and honors and handles incoming DSCP bits. The default is disabled.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:no access-policy
no access-policy
If you are upgrading from Release 3.7 or earlier to Release 5.1, disable access policies.
Syntax
no access-policy <1-65535>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-65535> Specifies the access policy ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:no boot config flags
autoboot
Syntax
no boot config flags autoboot
Default
None
Command mode
Global configuration mode
no cfm maintenance-association
Delete the CMF MA.
Syntax
no cfm maintenance-association <md-name> <ma-name>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<md-name> Specifies the MD name in a string of 122 characters.
<ma-name> Specifies the MA name in a string of 122 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:no cfm maintenance-domain
no cfm maintenance-domain
Delete the CFM MD.
Syntax
no cfm maintenance-domain <md-name>
Default
Command mode
Global configuration mode
Command parameters
Parameter Description
<md-name> Specifies the MD name in a string of 122 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:no cfm maintenance-
endpoint
no cfm maintenance-endpoint
Delete an existing CFM MEP.
Syntax
no cfm maintenance-endpoint <nd-name> <ma-name> <mepID>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<md-name> Specifies the MD name in a string of 122 characters.
<ma-name> Specifies the MA name in a string of 122 characters.
<mepID> Specifies the MEP ID. Range is 18191.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:no cfm maintenance-
endpoint enable
Syntax
[no] cfm maintenance-endpoint <md-name> <ma-name> <mepID> enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<md-
name> Specifies the MD name in a string of 122 characters.
<ma-
name> Specifies the MA name in a string of 122 characters.
<mepID> Specifies the MEP ID. Range is 18191.
enable Enables an existing MEP. Use this parameter with the No option to disable an existing
MEP.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:no ip igmp snoop-querier
no ip igmp snoop-querier
Disables snoop querier.
Syntax
Default
The default is disabled.
Command mode
VLAN Interface configuration code
no ip igmp snoop-querier-addr
Sets the snoop querier address to none.
Syntax
Default
None
Command mode
VLAN Interface configuration code
no ip msdp peer
Delete an MSDP peer to permanently remove the peer relationship from the configuration.
Syntax
no ip msdp peer <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
A.B.C.D Specifies the IP address of the router that is the MSDP peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:no ip msdp redistribute
route-policy
Syntax
no ip msdp redistribute route-policy
Default
None
Command mode
Global configuration mode
no ip route
Delete a dynamically learned route from the routing table if you do not want the Ethernet Routing Switch to use the route.
Exercise caution when you delete entries from the routing table.
Syntax
no ip route <A.B.C.D> <A.B.C.D> <A.B.C.D> dynamic
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
dynamic Specifies that a dynamic route is to be deleted.
{A.B.C.D} Specifies the IP address, the subnet mask, and the next-hop IP address, respectively.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:no ipvpn
no ipvpn
Administratively disable IP VPN on a VRF to remove it from service for troubleshooting purposes or if you need to change the
route distinguisher.
Syntax
no ipvpn
Default
None
Command mode
Global configuration mode
no ist enable
Disable an interswitch trunk.
Syntax
no ist enable
Default
None
Command mode
Global configuration mode
no ist peer-ip
Delete an interswitch trunk.
Syntax
no ist peer-ip
Default
None
Command mode
Global configuration mode
no-med-path-is-worst
Enable BGP to treat an update without a multiexit discriminator (MED) attribute as the worst path.
Syntax
no-med-path-is-worst enable
Default
The default value is enable.
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables BGP to treat an update without a multiexit discriminator (MED) attribute as the
worst path.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:no mlt member
no mlt member
Remove ports from an MLT LAG.
Syntax
no mlt <mlt-id> member <portlist>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
portlist Specifies the slot and the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:no pcap enable
no pcap enable
Disable PCAP and clear the PCAP DRAM buffer and the PCAP counters.
Syntax
no pcap enable
Default
None
Command mode
Global configuration mode
Syntax
no pcap enable
Default
None
Command mode
Global configuration mode
no qos 802.1p-override
Configure a port as trusted to determine the Layer 2 QoS actions the switch performs. A trusted port (override disabled) honors
incoming 802.1p bit markings.
Syntax
no qos 802.1p-override
Default
The default is disabled.
Command mode
Global configuration mode
no tacacs enable
Disable TACACS+ authentication to remove the centralized validation of users attempting to gain access to a router or network
access server.
Syntax
no tacacs enable
Default
None
Command mode
Global configuration mode
no tacacs server
Delete a TACACS+ server to remove the centralized validation of users attempting to gain access to a router or network access
server.
Syntax
no tacacs server <ipaddr>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<A.B.C.D> Specifies the IP address of the server you want to delete.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:nsna enable
nsna enable
Globally enable the configuration settings in NSNA.
Syntax
nsna enable
Default
None
Command mode
Global configuration mode
nsna nsnas
Configure the NSNA server to allow VLANs with policy restrictions to enforce security policies for end users.
Syntax
nsna nsnas <A.B.C.D/0-32> port <1024-65535>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
port <1024- Specifies the TCP port number used by Switch SNAS Communication Protocol
65535> (SSCP).
A.B.C.D/0-32 -
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:nsna phone-signature
nsna phone-signature
Add an IP phone signature string to an NSNA IP phone device.
Syntax
nsna phone-signature <WORD>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<WORD> Specify the phone signature string in the range of 164 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:nsna port
nsna port
Configure the access ports for NSNA.
Syntax
nsna port <portList> dynamic [voip-vlans <1-4094>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<portList> Specify the port or a list of ports in the following format: {slot/port[-
slot/port][,...]}
voip-vlans <1-
4094> Specify the ID of the VoIP VLAN added to the table list.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:nsna uplink vlans
Syntax
nsna uplink vlans <vidList>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
vlans <vidList> The VLAN ID created with an NSNA color filter.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:nsna vlan
nsna vlan
Configure the filters for policy restrictions for NSNA users.
Syntax
nsna vlan <1-4094> color {red| green|yellow|voip} filter-id <WORD> filter-name <WORD>
yellow-subnet <A.B.C.D/0-32>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specify the following access on a NSNA VLAN: red-Restricted access
allowing only authentication, DHCP and DNS traffic to the Secure
Network Access Switch (SNAS), DHCP and DNS servers. yellow-
color
{red|yellow|green|voip} Limited access allowing traffic to only remediation networks. green-
Full (or with certain restriction per policy) access based on user
groups. voip-Restricted access allowing VoIP traffic to VoIP controllers
and authenticated IP phone peers.
filter-id <WORD> The ID of the filter in the range of 14095. If the specified filter ID
does not exist, a default filter of the specified color is autogenerated.
filter-name <WORD> Specify a name for the filter in the range of 132 characters.
vlan <1-4094> The ID of the VLAN.
yellow-subnet Specify a VLAN subnet IP and mask for remedial network. This option
<A.B.C.D/0-32> is present only when creating yellow VLANs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ntp authentication-key
ntp authentication-key
Create a NTP authentication key.
Syntax
ntp authentication-key <1-2147483647> <word>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
authentication-key Creates an authentication key for MD5 authentication. To set this option
<1-2147483647>
<word> to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ntp interval
ntp interval
Enable Network Time Protocol (NTP) globally.
Syntax
ntp interval <10-1440>
Default
The default is 15 minutes.
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the time interval (101440 minutes) between successive NTP updates.
interval Important If NTP is already activated, this configuration does not take effect until you
<10-
1440> disable NTP and then reenable it. To set this option to the default value, use the default
operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ntp server
ntp server
Add an NTP server or modify existing NTP server parameters. You can configure a maximum of 10 time servers.
Syntax
ntp server <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<A.B.C.D> Specifies the ip address of the NTP server to be added or modified.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ntp server auth-enable
Syntax
ntp server <A.B.C.D> [auth-enable] [authentication-key <0-2147483647>] [enable]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
auth- Activates MD5 authentication on this NTP server. The default is no MD5 authentication.
enable To set this option to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:overload
overload
Set or clear the overload condition.
Syntax
[no] [default] overload
Default
The default value is false.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value of false.
default Use the default option to set this parameter to the default value of false.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:overload-on-startup
overload-on-startup
Set the IS-IS overload-on-startup value in seconds. The overload-on-startup value is used as a timer to control when to send out
LSPs with the overload bit cleared after IS-IS startup.
Syntax
[no] [default] overload-on-startup <overload-on-startup>
Default
The default value is 20.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value of 20.
default Use the default option to set this parameter to the default option of 20.
<overload-on- Specifies the IS-IS overload-on-startup value in seconds. Range is 15
startup> 3600.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:password access-level
password access-level
Enable CLI access levels to control the configuration actions of various users.
Syntax
password access-level <WORD>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Permits or blocks this access level. The available access levels are: l4admin l4oper layer1
<word> layer2 layer3 <word> oper read-only <word> read-write <word> read-write-all
<word> slbadmin slboper ssladmin <word> represents the new password with 020
access
level characters. Layer 4 administrator and operator access levels are used to connect to the
Web Switching Module (WSM). For more information about Web Switching Module
(WSM), see Avaya Ethernet Routing Switch 8800/8600 Web Switching Module
Fundamentals (NN46205-314).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:password aging-time
password aging-time
Configure the duration of your password for when it expires.
Syntax
password aging-time day <1-365>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
aging-time day
<1-365> Configures the age-out time for passwords, in days.
access level
<WORD 2-8> Allows or blocks this access level. no password access-level <WORD 2-8>
aging-time day Specifies the number of days that the password is enabled. day has a
<1-365> configurable range of 1365.
default- Changes the default lockout time after three invalid attempts. secs is the
lockout-time lockout time in seconds and is in the range of 60 to 6500. The default is 60
<60-65000> seconds.
lockout Sets the host lockout time. A.B.C.D is the host IP address. ipv6addr is the IP
{A.B.C.D| address for ipv6 address. time is the lockout-out time in seconds for passwords
ipv6addr} [time
<60-65000>] lockout in the range of 60 to 65000. The default is 60 seconds.
min-passwd-len Sets the minimum length for passwords in high-secure mode. The range is from
<10-20> a minimum of 10 to 20.
password- Specifies the number of previous passwords to remember. Password-history has
history <3-32> a configurable range of 3 to 32. The default is 3.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:password default-lockout-
time
password default-lockout-time
Change the default lockout time after three invalid attempts.
Syntax
password default-lockout-time <60-65000>
Default
The default is 60 seconds.
Command mode
Global configuration mode
Command parameters
Parameter Description
default- Changes the default lockout time after three invalid attempts. Configures the lockout
lockout- time in seconds and is in the range of 6065000. To set this option to the default
time <60-
65000> value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:password lockout
password lockout
Configure the host lockout time for passwords.
Syntax
password lockout WORD <0-46> time <60-65000>
Default
The default is 60 seconds.
Command mode
Global configuration mode
Command parameters
Parameter Description
lockout WORD Configures the host lockout time. word is the Host Internet Protocol (IP) address
<0-46> time in the format a.b.c.d. time is the lockout-out time in seconds for passwords
<60-65000> lockout in the range of 6065000.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:password min-passwd-len
password min-passwd-len
Configure the minimum length for passwords in high-secure mode.
Syntax
password min-passwd-len <10-20>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
min-passwd- Configures the minimum length for passwords in high-secure mode. To set this
len <10-20> option to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:password password-history
password password-history
Specify the number of previous passwords to remember on the port.
Syntax
password password-history
Default
The default is 3.
Command mode
Global configuration mode
Command parameters
Parameter Description
password- Specifies the number of previous passwords to remember. To set this option to the
history <3-
32> default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:passwordprompt
passwordprompt
Change the password prompt to configure the run-time environment and define the generic configuration settings for ACLI
sessions.
Syntax
passwordprompt <string>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Changes the ACLI password prompt. string is an ASCII string from 11510
passwordprompt characters. Use the default option before this parameter, default passwordprompt,
<string> to enable using the default password string. Use the no operator before this
parameter, no passwordprompt, to disable the default password string.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:pcap 1-1000
pcap 1-1000
Configure PCAP on a port so that the port supports PCAP, and to apply filters to the captured data. You can apply IP- or Access
Control List (ACL)-based filters.
Syntax
pcap <1-1000>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Adds an IP filter set (Global or Source
Destination) to a port. <1-1000> specifies
the filter set. The IP filter set must already
exist. Filter Global Set ID values are in the
range of 1 to 100 and Source/Destination
sets are in the range of 300 to 1000. Adding
a filter set causes the following to happen:
<1-1000> Creates an IP traffic filter for a port if one
does not already exist; otherwise, disables
the IP traffic filter. Adds the IP traffic filter
set to the port. Sets the mirror bit for all the
filters in the set. Restores the default-action
of the port. If default-action was not set, set
to forwarding. Enables the traffic filter on
the port.
acl-filter <1-4096> Applies an ACL to captured packets. The
ACL ID can be from 1 to 4096.
Enables or disables PCAP on the port. The
default PCAP mode captures ingress packets
enable [mode
<tx|rx|both|rxFilter|txFilter|bothFilter>] (rx mode). If PCAP is enabled in filter mode,
then only packets which match the filter
criteria are captured.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:pcap capture-filter
pcap capture-filter
Use capture filters to better define the match criteria used on packets.Avaya highly recommends using PCAP with IP or MAC filters
to reduce the load on the PCAP engine.
Syntax
pcap capture-filter <1-1000>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Determines the action taken by the filter. capture indicates
that the packet is captured. drop indicates that the packet
is dropped. trigger-on indicates to start capturing the
action <capture|drop|trigger- packet when a packet matches this filter. PCAP is enabled
on|trigger-off> globally and the trigger filter is disabled. trigger-off
indicates to stop capturing the packet when a packet
matches this filter. PCAP is disabled globally and the trigger
filter is disabled.
Specifies the DSCP value of the packet. <0-63> is the
DSCP from 0 to 63. The default is 0, which means this
dscp <0-63> [<0-63>] [match-
zero] option is disabled. Use the second <0-63> to specify a
range. When match-zero is set, 0 is considered a valid
value. When it is not set, 0 is considered a disable value.
Specifies the destination IP address. The default is 0.0.0.0,
dstip <A.B.C.D> [<A.B.C.D>] which means this option is disabled. Use the second
<A.B.C.D> to specify a range.
dstmac Specifies the MAC address of the destination. If the mask is
<0x00:0x00:0x00:0x00:0x00:0x00> set, then only the first few bytes are compared. <1-6> is
[<1-6>] the destination MAC address mask, and specifies a range.
enable Enables the filter. The default is disable.
Specifies the Ethernet type of the packet. <Ethertype> is
ether-type <0x0-0xffff> [<0x0-
0xffff>] an Ether-type. The default is 0, meaning that this option is
disabled. Use the second <0x0-0xffff> to specify a range.
When set, PCAP stops after capturing the specified number
of packets. This is similar to the refresh-timer option; after
packet-count <0-65535> it is invoked, the filter is disabled. This option is active only
when the action parameter is set to trigger-on. The default
value is 0, which means this option is disabled.
Specifies the priority bit of the packet. The default is 0,
which means this option is disabled. Use the second <0-7>
pbits <0-7> [<0-7>] [match-
zero] to specify a range. When match-zero is set, 0 is considered
a valid value. When it is not set, 0 is considered a disable
value.
Specifies the packet protocol type. The default is 0, which
protocol-type <0-255> [<0-
255>] means this option is disabled. Use the second <0-255> to
specify a range.
When set, this starts or resets a timer. If another packet is
not received within the specified time, PCAP is disabled
refresh-timer <WORD 1-7> globally. This option is active only when the action
parameter is set to 'trigger-on'. To delete this option, set it
to 0. The default value is 0.
Specifies the source IP address. The default is 0.0.0.0,
srcip <A.B.C.D> [<A.B.C.D>] which means this option is disabled. Use the second
<A.B.C.D> to specify a range.
Specifies the MAC address of the source. If the mask is set,
srcmac then only the first few bytes are compared. The default is
<0x00:0x00:0x00:0x00:0x00:0x00> 00:00:00:00:00:00, which means this option is disabled.
[<1-6>] <1-6> is the mask of the source MAC address. This
parameter specifies an address range.
Specifies the TCP port of the packet. The default is 0,
tcp-port <0-65535> [<0-65535>] which means this option is disabled. Use the second <0-
65535> to specify a range.
When set, PCAP is invoked when the first packet is
matched and stopped after the set value of time. After
starting the timer, the filter is disabled. This option is active
timer <WORD 1-7> only when the action parameter is set to trigger-on.
<WORD 1-7> is a value from 100 to 3600000 milliseconds.
The default value is zero. Setting the value to 0 disables
the timer.
Specifies the UDP port of the packet. The default is 0,
udp-port <0-65535> [<0-65535>] which means this option is disabled. Use the second <0-
65535> to specify a range.
Sets a user defined value on which to match the packet.
The user can define a pattern in hex or characters to
user-defined <0-9600> <WORD 0- match (<0-9600>). The user can also specify the offset to
50> start the match (<WORD 0-50>). The default value of
pattern is null ('') which means that this field is discarded.
To disable this option, set the pattern to null ('').
Specifies the VLAN ID of the packet. The default is 0, which
vid <0-4092> [<0-4092>] means that this option is disabled. Use the second <0-
4092> to specify a range.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:pcap enable
pcap enable
Enable PCAP globally.
Syntax
pcap enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
auto-save
[file-name Enables or disables autosave. When enabled, saves the captured frames into the
<WORD 1- device specified and continues to capture frames. The default is enable. If this option
40>] is disabled, packets are stored in the DRAM buffer only. file-name <WORD 1-40> is
[pcmcia] the name of the file where captured frames are saved. pcmcia sets the device to
[network] PCMCIA. network sets the device to network. ip <A.B.C.D> is the IP address used.
[ip This is used only if the device is network.
<A.B.C.D>]
Specifies the size of the buffer allocated for storing data. A nonMezz SF/CPU can be
buffer-size
<2-420> up to 256 MB, a Mezz SF/CPU can use up to 420 MB. The maximum buffer size is
104 MB for a 8691 SF/CPU. The default is 32 MB.
Enables buffer wrapping. When this parameter is set to true and the buffer becomes
buffer-wrap full, the capture continues by wrapping the buffer. If this parameter is set to false
and the buffer becomes full, the packet capture stops. The default value is true. A
log message is generated when the buffer is wrapped.
enable Enables PCAP globally. The default is disabled. To disable PCAP, use the no pcap
enable command.
ethertype-
for-svlan- Specifies the Ethernet type for sVLAN packets. With this information, PCAP can
level identify and capture the tag information of packets received from SVLAN ports.
<0x5dd- <0x5dd-0xffff> is a hexadecimal value. The default is 0x8100.
0xffff>
fragment- Specifies the number of bytes from each frame to capture. The default is the first 64
size <64-
9600> bytes of each frame.
Enables PCMCIA wrapping. When this parameter is set to true and the autosave
pcmcia-wrap device is PCMCIA, this causes an overwrite of the present file on the PCMCIA during
an autosave. If this parameter is set to false, the present file is not overwritten. A log
is generated when the file is overwritten on the PCMCIA.
This command resets the PCAP engine DRAM buffer, as well as all software counters
reset-stat used for PCAP statistics. This command can be executed in the Primary or Secondary
SF/CPU.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:pcap enable mode
Syntax
pcap enable [mode <tx|rx|both|rxFilter|txFilter|bothFilter>]
Default
None
Command mode
Global configuration mode
pcap reset-stat
Reset PCAP statistics and counters.
Syntax
pcap reset-stat
pcap reset-stat
Default
None
Command mode
Global configuration mode
peer telnet
Access the standby SF/CPU to make changes to the standby SF/CPU without reconnecting to the console port on that module.
Syntax
peer <telnet|rlogin>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
(telnet|rlogin) Specifies either Telnet or rlogin to use to access the standby SF/CPU.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ping
ping
Use ping operations to determine that a path exists to another device, and that it is reachable.
Syntax
ping <HostName/ipv4address/ipv6address> [scopeid <value>] [datasize <value>] [count
<value>] [-s] [-I <value>] [-t <Value>] [-d]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Configures the number of times to ping (for IPv4/IPv6). The range is 19
count <value> 999.Important To specify a count for the ping operation, you must also
specify a size. For example,ping 8888:0:0:0:0:0:0:1
-d <value> Configures ping debugging (for IPv4/IPv6).
datasize <value> Configures the size of ping data sent in bytes, for IPv4:164076, for IPv6:
16-65487.
HostName/ipv6address Specifies the host name or IPv6 (x:x:x:x:x:x:x:x) address {string length
1256}.
-I <value> Configures the interval between transmissions in seconds (160).
-s Configures the continuous ping at the interval rate defined by the [-I]
parameter (for IPv4/IPv6).
scopeid <value> Configures the circuit ID (for IPv6) (19999).
-t <value> Configures the no answer timeout value (for IPv4/IPv6) {1120}.
-d Sets the ping debug flag. In debug mode, the ping reply includes
additional information about the device being pinged.
-s Specifies that the IPv4 or IPv6 ping should be retransmitted at continuous
intervals at the interval defined by -I <1-60>.
-I <1-60> Specifies the interval between ping retransmissions from 1 to 60 seconds.
-t <1-120> Specifies the no-answer timeout from 1 to 120 seconds.
count <1-9999> Specifies the number of times to ping the device from 1 to 9999. The
default is 1.
datasize <16-4076> Specifies the size of the ping packet in octets, either 16 to 4076, or 16 to
65487. The default is 16 octets.
scopeid <1-9999> Specifies the circuit scope ID for IPv6 from 1 to 9999.
source <WORD 1-256> Specifies the source IP address for use in IP VPN pings.
vrf <WORD 0-16> Specifies the VRF instance by VRF name.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ping hostname
ping hostname
Ping a device to test the connection between the Ethernet Routing Switch 8800/8600 and another network device.
Syntax
ping <HostName/ipv4address/ipv6address> [scopeid <value>] [datasize <value>] [count
<value>][-s] [-I <value>] [-t <value>] [-d] [vrf <word>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
HostName/ipv4address/ipv6address Specifies the Host Name or IPv4 (a.b.c.d) or IPv6
(x:x:x:x:x:x:x:x) address (string length 1256).
scopeid value Specifies the circuit ID (for IPv6) (19999).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ping-mpls ipv4
ping-mpls ipv4
Ping an MPLS device.
Syntax
ping-mpls ipv4 <prefix/len> [ttl <1-255>] [source <A.B.C.D>] [count <1-1000>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
prefix/len Specifies the IPv4 address and prefix length.
count <1-1000> Specifies the number of times to ping the device from 1 to 1000. The default is
1.
ttl <1-255> Specifies the time-to-live of the MPLS ping packet from 1 to 255.
source
<A.B.C.D> Specifies the source IP address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ping-mpls rsvp
ping-mpls rsvp
Ping an MPLS device.
Syntax
ping-mpls rsvp <WORD 0-32> [ttl <1-255>] [source <A.B.C.D>] [count <1-1000>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Word <0-32> Specifies the name of the label-switched path.
count <1-1000> Specifies the number of times to ping the device from 1 to 1000. The default is
1.
ttl <1-255> Specifies the time-to-live of the MPLS ping packet from 1 to 255.
source
<A.B.C.D> Specifies the source IP address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ping-snoop
ping-snoop
Use Ping Snoop to troubleshoot multilink trunking configurations.
Syntax
ping-snoop <A.B.C.D/0-32> <A.B.C.D/0-32
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<A.B.C.D/0-32> Creates the ping snoop filter by specifying the source IP address and
<A.B.C.D/0-32> the destination IP address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:pluggable-optical-module
pluggable-optical-module
Configure Digital Diagnostic Interface (DDI) on Digital Diagnostic Monitoring to get information concerning the status of the
transmitted and received signals to allow better fault isolation and error detection.
Syntax
pluggable-optical-module ddm-alarm-portdown
Default
The default is disable.
Command mode
Global configuration mode
Command parameters
Parameter Description
ddm-alarm- Sets the port down when an alarm occurs. When enabled, the port goes down
portdown when any alarm occurs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:portlock enable
portlock enable
Enable port locking for the security of the ports from any modifications.
Syntax
portlock enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the port locking globally.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:port-phy portlist
port-phy portlist
Specify the line and the connector that you want to be active.
Syntax
port-phy [port <portList>] <left|right>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<left|right> For duplex connectors, specifies which line and connector you want to be active: left
or right.
portlist Specifies the slot and the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:psnp-interval
psnp-interval
Specify the Partial Sequence Number Packets (PSNP) interval in seconds. This is a system level parameter that applies for L1 PSNP
generation on all interfaces.
Syntax
[no] [default] psnp-interval <psnp-interval>
Default
The default value is 2.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value of 2.
default Use the default option to set this parameter to the default value of 2.
<psnp-interval> Specifies the PSNP interval in seconds. Range is 1120.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:qos 802.1p-override
qos 802.1p-override
Configure a port as untrusted to determine the Layer 2 QoS actions the switch performs. An untrusted port (override enabled)
overrides 802.1p bit markings.
Syntax
qos 802.1p-override [enable]
Default
The default is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
If you configure this variable, it overrides incoming 802.1p bits; if you do not configure
this variable, it honors and handles incoming 802.1p bits. The default is disable (Layer 2
enable trusted). To use the default configuration, use the default option in the command default
qos 802.1p-override [enable] To delete the current configuration, use the no option in
the command no qos 802.1p-override [enable]
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:qos apply egress-queue-set
Syntax
qos apply egress-queue-set <1-386>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-386> Identifies the egress queue template.
Applies the egress queue set when you issue the command. When you create an egress
apply queue set, apply occurs when you issue the command. When you modify a queue set,
apply occurs after you save the configuration and boot the switch. This command is
available only in Privileged EXEC mode.
<1-386> Identifies the egress queue template.
Applies the egress queue set when you issue the command. When you create an egress
apply queue set, apply occurs when you issue the command. When you modify a queue set,
apply occurs after you save the configuration and boot the switch. This command is
available only in Privileged EXEC mode.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:qos egressmap exp
Syntax
qos egressmap exp <0-7> <0-7>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
exp <0-7> <0-7> Maps the QoS level to MPLS EXP level.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:qos egress-queue-set
qos egress-queue-set
Associate ports with the egress queue set.
Syntax
qos egress-queue-set <1-386> <portList>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-386> Identifies the egress queue set.
<portList> Specifies the list of ports. To remove ports to an egress queue set, use the following
command: no qos egress-queue-set <1-386> <portList>
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:qos egress-queue-set qmax
Syntax
qos egress-queue-set qmax <1-386> <8|64> balanced-queues <0-48>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-386> Identifies the egress queue template.
balanced-
queues <0- Specifies the maximum number of balanced queues in the egress queue set.
48>
qmax Specifies the maximum number of queues, either 8 or 64. The sum of the number of
<8|64> queues for balanced, hipri, and lopri queues must be less than or equal to qmax.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:qos egress-queue-set queue
Syntax
qos egress-queue-set queue <1-386> <0-63> [max-length <0-32760>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<0-63> Identifies the queue.
<1-386> Identifies the egress queue template.
max- Specifies the limit to which a queue can grow. The queue length does not imply that a
length queue has a fixed number of buffers. For example, a queue can grow to full memory size
<0-
32760> of 32 K buffers.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:qos if-policer
qos if-policer
Configure a port policer to bandwidth-limit incoming traffic. The switch drops or remarks violating traffic. Only RS modules support
this policer.
Syntax
qos if-policer [port <portList>] police-rate <1000-10000000>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
police-rate <1000 Specifies the ingress rate limit (policing limit) in Kb/s. The range is
10000000> 100010000000.
port <portList> Specifies the slot and port or slot and portlist.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:qos if-shaper
qos if-shaper
Configure port-based shaping to rate-limit all outgoing traffic to a specific rate.
Syntax
qos if-shaper [port <portList>] shape-rate <1000-10000000>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
port <portList> Specifies the slot and port, or slot and portlist.
shape-rate <1000-10000000> Configures the shaping rate from 100010000000 Kb/s.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:qos ingressmap exp
Syntax
qos ingressmap exp <0-7> <0-7>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
exp <0-7> <0-7> Maps the MPLS EXP bit to a QoS level. Each option has a range from 07.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:qos level port
Syntax
qos level [port <portList>] <0-6>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the default QoS level for the port traffic. QoS level 7 is reserved for network
<0-6> control traffic. The default is 1. To use the default configuration, use the default option
in the command default qos level
port
<portList> Specifies the slot and port, or slot and port list.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:qos level vlan
Syntax
qos level <0-6>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the default QoS level for the VLAN traffic. QoS level 7 is reserved for network
<0-6> control traffic. The default is 1. To use the default configuration, use the default option in
the command default qos level.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:qos policy
qos policy
Configure a QoS policy to configure peak and service policing rates for specific lane members.
Syntax
qos policy <1-16383> peak-rate <250-10000000> svc-rate <250-10000000> [lanes <WORD 1-128>]
[name <WORD 1-32>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-16383> Specifies the policer ID number.
peak-rate <250-
10000000> Configures the policer peak rate in Kb/s.
srv-rate <250-
10000000> Configures the policer service rate in Kb/s.
lane <WORD 1-128> Specifies the lanes to which the policer applies:all slot/lane [-
slot/lane][,-]
name <WORD 1-32> Names the policer template.
port <portList> Specifies the slot and port, or slot and port list.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:quick-start
quick-start
Enable the quick-start flag for exponential backoff.
Syntax
quick-start enable
Default
The default value is enable.
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the quick-start flag for exponential backoff.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:radius
radius
Configure RADIUS to authenticate users identity through a central database.
Syntax
radius
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
maxserver <1-10> Specific to RADIUS authentication. Sets the maximum number of servers
allowed for the device. The range is between 1 and 10.
access-priority- Specifies the value of the Access Priority attribute.in the range of 192 to
attribute <192-240> 240 and the default is 192.
auth-info-attr-value Specifies the value of the authentication-information attribute in the
<0-255> range of 0 to 255.The default is 91.
cli-commands- Specifies the value of the ACLI commands attribute in the range of 192
attribute <192-240> to 240 and the default is 195.
command-access- Specifies the value of the command access attribute in the range of 192
attribute <192-240> to 240 and the default is 194.
igap-passwd-attr
<standard|auth-info> Specifies the IGAP password attribute as standard or auth-info.
igap-timeout-log- Specifies the value of the igap-timeout-log-fsize in the range of 50 to
fsize <50-8192> 8192 KB. The default is 512.
mcast-addr-attr- Specifies the value of the multicast address attribute in the range of 0 to
value <0-255> 255. The default is 90.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:radius accounting
radius accounting
Configure RADIUS accounting variables.
Syntax
radius accounting [attribute-value <value> ] [include-cli-commands] enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
[attribute-value Specifies integer value for CLI command attribute, value of 192
<value>] 240.
[include-cli-commands ] Include CLI commands in RADIUS accounting updates.
enable Enable RADIUS accounting.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:radius cli-cmd-count
radius cli-cmd-count
Configure a RADIUS accounting interim request to create a log whenever more than forty CLI commands are executed.
Syntax
radius cli-cmd-count <1-40>
Default
The default value is 40.
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-40> Specifies a value of the ACLI command count in the range of 1 to 40.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:radius cli-profile
radius cli-profile
Use RADIUS ACLI profiling to grant or deny ACLI command access to users being authenticated by way of the RADIUS server.
Syntax
radius cli-profile
Default
None
Command mode
Global configuration mode
radius command-access-attribute
Configure RADIUS authentication and RADIUS accounting attributes to determine the size of the packets received.
Syntax
radius command-access-attribute <192-240>
Default
The default value is 192.
Command mode
Global configuration mode
Command parameters
Parameter Description
command-access- Specifies the RADIUS authentication attribute value is an integer value of
attribute <192-240> the ACLI command count in the range of 192 to 240.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:radius enable
radius enable
Enable or disable RADIUS authentication globally on the device to allow further configuration to take place.
Syntax
radius enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
maxserver <1-10> Specific to RADIUS authentication. Sets the maximum number of servers
allowed for the device. The range is between 1 and 10.
access-priority- Specifies the value of the Access Priority attribute.in the range of 192 to
attribute <192-240> 240 and the default is 192.
auth-info-attr-value Specifies the value of the authentication-information attribute in the
<0-255> range of 0 to 255.The default is 91.
cli-commands- Specifies the value of the ACLI commands attribute in the range of 192
attribute <192-240> to 240 and the default is 195.
command-access- Specifies the value of the command access attribute in the range of 192
attribute <192-240> to 240 and the default is 194.
igap-passwd-attr
<standard|auth-info> Specifies the IGAP password attribute as standard or auth-info.
igap-timeout-log- Specifies the value of the igap-timeout-log-fsize in the range of 50 to
fsize <50-8192> 8192 KB. The default is 512.
mcast-addr-attr- Specifies the value of the multicast address attribute in the range of 0 to
value <0-255> 255. The default is 90.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:radius enable eapol
Syntax
radius enable
Default
None
Command mode
Global configuration mode
radius igap-timeout-log-fsize
Set the timeout log file size to capture authentication and accounting information in an IGAP timeout log for each session.
Syntax
radius igap-timeout-log-fsize <value>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
igap-timeout-log-fsize Maximum size of IGAP timeout log file in kilobytes.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:radius mcast-addr-attr-
value
radius mcast-addr-attr-value
Set vendor-specific attributes to configure IGAP with RADIUS.
Syntax
radius mcast-addr-attr-value <value>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
mcast-addr-attr-value Integer value for the multicast address attribute in the range of 0
<value> to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:radius server host
Syntax
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<a.b.c.d> Indicates the IP address of the selected interface.
acct-port <value> Enables the server account UDP port. The value ranges form 1 to
65 536.
acct-enable <value> Enables the server account. This value is either true or false.
enable <value> Enables the server. This value is either true or false.
port <value> Server udp port and its value ranges from 1 to 65 536.
priority <value> Specifies the server priority and ranges from 1 to 10.
retry <value> Maximum number of retries. The allowed retries range from 0 to 6.
source-ip <value> IP address {a.b.c.d}.
timeout <value> No answer timeout value and the value ranges form 1 to 20.
WORD <0-32> Specifies the secret key. This value is a string in the range of 0 to
32 characters.
host <A.B.C.D> Create a host server.
key <WORD> Specify a secret key in the range of 0-20 characters.
Specify how the server functions: cli-configure the server for CLI
authentication. igap-configure the server for Internet Governance
used-by
{cli|igap|snmp|eapol|web} Advisory Protocol (IGAP) authentication. snmp-configure the server
for SNMP authentication. eapol-configure the server for EAPol
authentication. web-configure the server for Web authentication.
acct-enable Enables RADIUS accounting on this server.
acct-port <1-65536> Specify a UDP port of the RADIUS accounting server.
enable Enables this server.
port <1-65536> Specify a UDP port of the RADIUS server.
priority <1-10> Specify the priority value for this server.
retry <0-6> Specify the maximum number of authentication retries.
source-ip <A.B.C.D> Specify a configured IP address as the source address when
transmitting RADIUS packets.
timeout <1-20> Specify the number of seconds before the authentication request
times out.
<A.B.C.D> Specifies the IP address of the selected server.
key <WORD 0-20> Specifies the secret key, which is a string of up to 20 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:radius server host used-by
igap
Syntax
radius server host {a.b.c.d} used-by igap
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
{a.b.c.d} Indicates the IP address of the selected interface.
acct-port <value> Enables the server account udp port. The value ranges form 1 to 65 536.
acct-enable <value> Enables the server account. This value is either true or false.
enable <value> Enables the server. This value is either true or false.
port <value> Server udp port and its value ranges from 1 to 65 536.
priority <value> Specifies the server priority and ranges from 1 to 10.
retry <value> Maximum number of retries. The allowed retries range from 0 to 6.
source-ip <value> IP address {a.b.c.d}.
timeout <value> No answer timeout value and the value ranges form 1 to 20.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:radius-snmp acct-enable
radius-snmp acct-enable
Enable RADIUS accounting log all of the activity of each remote user in a session on the centralized RADIUS accounting server.
Syntax
radius-snmp acct-enable
Default
The default value is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
acct- Enables RADIUS accounting globally. RADIUS accounting cannot be enabled unless a
enable valid server is configured. This feature is disabled by default.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:radius sourceip-flag
radius sourceip-flag
Configure the source IP address if the outgoing interface on the Avaya Ethernet Routing Switch 8800/8600 fails so that
configuration changes be made to define the new RADIUS Client on the RADIUS Server.
Syntax
radius sourceip-flag
Default
None
Command mode
Global configuration mode
rd
Configure a unique route distinguisher to create globally unique VPN addresses.
Syntax
rd {<0-65535> <0-2147483647>|<A.B.C.D> <0-65535>}
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the route distinguisher (RD). Each VRF instance must use a
unique RD. The RD is a 6-byte value that you specify in one of the
following formats: Type 0-<AS number> <number> AS number is the
<0-65535> <0- assigned autonomous system (AS) number of the PE and number is an
2147483647>|<A.B.C.D>
<0-65535> assigned 4-byte value. Type 1-<ip-address> <number> ip-address is an
IPv4 address in the assigned prefix range of the PE and number is an
assigned 2-byte value. Important You must administratively disable the
IP VPN before you modify an existing RD configuration.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:redistribute
redistribute
Configure a redistribute entry to announce routes of a certain source protocol type into the BGP domain, for example, static, RIP,
or direct routes. Use a route policy to control the redistribution of routes. When used in IS-IS configuration mode, configures the
redistribution of the specified protocol into the SPBM network.
Syntax
[no] [default] redistribute {direct | bgp | ospf | rip | static} [metric <0-65535>]
[metric-type {internal | external}] [route-map <WORD 0-64>] [subnets {allow | suppress}]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable [vrf-src <WORD 0-
16>] Enables the BGP route redistribution instance.
redistribute enable
Enables the redistribution of the specified protocol into the SPBM network.
Syntax
[no] [default] redistribute {direct | bgp | ospf | rip | static} enable
Default
The default is disabled.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
no Disables the redistribution.
default Disables the redistribution.
{direct | bgp | ospf | rip | static} Specifies the protocol.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:redistribute isis
redistribute isis
Configure the redistribution of the specified protocol into the SPBM network. The protocol is specified by the command mode that
you choose: BGP, OSPF, or RIP.
Syntax
redistribute isis
Default
None
Command mode
BGP Router configuration mode
Syntax
redistribute isis enable [vrf-src <value>]
Default
None
Command mode
BGP Router configuration mode
Command parameters
Parameter Description
[vrf-src] Enables BGP redistribution for a VRF source.
[vrf-src Enables OSPF or RIP redistribution for a VRF source. Enter a VRF name from 0
<value>] 32 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:redistribute isis metric
Syntax
redistribute isis metric <0-65535>
Default
None
Command mode
BGP Router configuration mode
Command parameters
Parameter Description
<value> Type a metric value between 065535.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:redistribute isis metric-type
Syntax
redistribute isis metric-type {type1 | type2}
Default
None
Command mode
OSPF Router Configuration mode
Command parameters
Parameter Description
{type1} Specifies a type 1 metric. For metric type 1, the cost of the external routes is equal to the
sum of all internal costs and the external cost.
{type2} Specifies a type 2 metric. For metric type 2, the cost of the external routes is equal to the
external cost alone. The default is type 2.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:redistribute isis route-map
Syntax
redistribute isis route-map <WORD 0-64>
Default
None
Command mode
BGP Router configuration mode
Command parameters
Parameter Description
<WORD 064> Specifies the policy name. Type a name between 064 characters in length.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:redistribute isis route-policy
Syntax
redistribute isis route-policy <WORD 0-64>
Default
None
Command mode
OSPF Router Configuration mode
Command parameters
Parameter Description
<WORD 064> Specifies the policy name. Type a name between 064 characters in length.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:redistribute isis subnets
Syntax
redistribute isis subnets {allow | suppress}
Default
None
Command mode
OSPF Router Configuration mode
Command parameters
Parameter Description
[allow] Allows external subnet route advertisements.
[supress] Suppresses external subnet route advertisements.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:redistribute ospf
redistribute ospf
Configure a redistribute entry to announce certain routes into the RIP domain, including static routes, direct routes, RIP, OSPF, or
BGP. Optionally, use a route policy to control the redistribution of routes.
Syntax
redistribute <ospf|bgp|static|direct|rip> [vrf-src <WORD 0-16>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<ospf|bgp|static|direct|rip> Specifies the type of routes to be redistributed (the protocol
source).
vrf <WORD 0-16> Specifies the VRF instance.
vrf-src <WORD 0-16> Specifies the source VRF instance. This parameter is not
required for redistribution within the same VRF.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:remote-mirroring
remote-mirroring
Use remote mirroring to monitor many ports from different switches using one network probe device.
Syntax
remote-mirroring [enable] [mode <source|termination>] [srcMac
<0x00:0x00:0x00:0x00:0x00:0x00>] [dstMac <0x00:0x00:0x00:0x00:0x00:0x00>] [ether-type
<0x00-0xffff>] [vlan-id <1-4094>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Sets the destination MAC address for use in the remote
mirroring encapsulation header. The mirrored packet is sent
dstMac to this MAC address. The DstMac is used only for RMS
<0x00:0x00:0x00:0x00:0x00:0x00> ports. For RMT ports, one of the unused MAC addresses
from the switch port MAC address range is used. This MAC
address is saved in the configuration file.
Enables remote mirroring on the port. When remote
mirroring is enabled, the following events occur: A static
entry for the DstMac is added to the Forwarding Database
enable (FDB). All packets that come with this remote mirroring
DstMac are sent to the RMT port. The switch periodically
(once in 10 seconds) transmits broadcast Layer 2 packets
in the associated VLAN so that all nodes in the network can
learn the DstMac.
ether-type <0x00-0xffff> Specifies the Ethertype of the remote mirrored packet. The
default value is 0x8103.
mode <source|termination> Specifies whether the port is an RMT (mode is termination)
or an RMS (mode is source).
Sets the source MAC address for use in the remote
mirroring encapsulation header. The mirrored packet is sent
from the RMS port, and the source MAC parameter in the
srcMac header is derived from this address. The source MAC
<0x00:0x00:0x00:0x00:0x00:0x00> address of the encapsulated frame contains the first 45 bits
of this MAC address. The three least significant bits are
derived from the port number of the RMS port. The MAC
address of the port is used as the default value.
Specifies to which VLAN the remote mirroring destination
MAC address belongs. This must be a port-based VLAN.
vlan-id <1-4094> Used only for Remote Mirroring Termination (RMT) ports.
When the RMT port is removed from the last VLAN in the
list, RMT is disabled on the port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:remote-vlan-stg
remote-vlan-stg
Assigns the spanning tree group to the remote VLAN. The 255 value clears the configuration.
Syntax
remote-vlan-stg <1-64, 255>
Default
None
Command mode
WLAN Switch Configuration
Command parameters
Parameter Description
<164, Assigns the spanning tree group to the remote VLAN. The 255 value clears the
255> configuration.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:remove word
remove word
Remove files to make space.
Syntax
remove <WORD 1-99> [-y]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<WORD 1-99> <WORD 1-99> specifies the file to remove.
-y Skip the confirm question.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:reset
reset
Reset the switch to reload system parameters from the most recently saved configuration file.
Syntax
reset [-y]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
-y Suppresses the confirmation message before the switch resets. If you omit this
parameter, you are asked to confirm the action before the switch resets.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:retransmit-lsp-interval
retransmit-lsp-interval
Specify the minimum time between retransmission of an LSP. This defines how fast the switch resends the same LSP. This is a
system level parameter that applies for L1 retransmission of LSPs.
Syntax
[no] [default] retransmit-lsp-interval <retransmit-lsp-interval>
Default
The default value is 5.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value of 5.
default Use the default option to set this parameter to the default value of
5.
<retransmit-lsp-
interval> Specifies the retransmit-lsp-interval in seconds. Range is 1300.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:rip enable
rip enable
Enable RIP globally.
Syntax
enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Globally enables RIP on the VRF or switch.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:rmon
rmon
Configure RMON functions on the switch to set alarms and capture events.
Syntax
rmon
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
alarm <1-65535> <WORD
1-536> <1-3600> Creates an alarm interface. <1-65535> is the interface index number
{absolute | delta} from 165535. <WORD 1-1536> is the variable name or OID, case
rising-threshold <- sensitive (string length 11536). {absolute | delta} is the sample type.
2147483648- rising-threshold <-2147483648-2147483647> [<event:1-65535>] is the
2147483647> rising threshold (21474836482147483647) and the rising event
[<event:1-65535>] number (165535). falling-threshold <-2147483648-2147483647>
falling-threshold <-
2147483648- [<event:1-65535>] is the falling threshold (21474836482147483647)
2147483647> and the falling event number (165535). owner <WORD 2-127> is the
[<event:1-65535>] name of the owner (string length 148). default rmon alarm <65535> is
[owner <WORD 2-127>] the default rmon alarm configuration. Use the no operator to disable
default rmon alarm RMON alarms: no rmon alarm [<1-65535>]
<1-65535>
Creates an ether-stats control interface. <1-65535> is the index
stats <1-65535> number of the ether stats control interface. portList is the single port
<portList> [owner interface {slot/port[-slot/port][,...]}. owner <WORD 1-127> is name of
<WORD 1-127>] the owner (string length 1127). Use the no operator to delete a stats
control interface: no rmon stats [<1-65535>]
Creates an event. <1-65535> is the event index number. [log] displays
event <1-65535> [log] information about configured traps. [trap] specifies trap source and
[trap] [description destination IP addresses. description <LINE> is the event description
<LINE>] [owner (string length 0127). owner <WORD 1-127> is the name of the owner
<LINE>] [trap_src (string length 1127). trap_src <A.B.C.D> is the trap source ip address.
<A.B.C.D>] [trap_dest trap_dest <A.B.C.D> is the trap destination ip address. community
<A.B.C.D>] [community <WORD 1-27> is the event community (string length 1127). Use the
<WORD 1-127>] no operator to delete a RMON event: no rmon event [<1-65535>] [log
]
Creates a history control interface. <1-65535> is the index number of
history <1-65535> the history control interface (165535). <portList> is the single port
<portList> interface {slot/port[-slot/port][,...]}. [<buckets:1-65535>] is the
[<buckets:1- number of buckets requested (165535). [<interval:1-3600>] is the
65535>][<interval:1- time interval in seconds over which the data is sampled for each bucket
3600>][owner <WORD 1- (13600). [owner <WORD 1-127>] is the name of the owner (string
127>] length 148). Use the no operator to delete a history control interface:
no rmon history [<1-65535>]
memsize <250000- Configures the amount of RAM in bytes to allocate for RMON. The range
4000000> is 2500004000000.
Controls whether the RMON traps are sent to the owner or to all trap
trap-option
<toOwner|toAll> recipients. toOwner|toAll is set to either the owner or to all trap
recipients.
util-method
<half|full> Controls whether port utilization is calculated in half or full duplex.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:route-map
route-map
Edit a route policy.
Syntax
route-map Word<1-64> <1-65535>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
165535 Specifies the integer sequence number in the range of 165535. A sequence number acts
as an implicit preference; a lower sequence number takes preference.
Word <1 Specifies the name, up to 64 characters for the policy.
64>
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:route-map enable
route-map enable
Configure and enable a route policy so that the switch can control routes that certain packets can take.
Syntax
route-map <WORD 1-64> <1-65535> enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables a route policy with a policy name and a
sequence number.
If configured, the switch matches the as-path
attribute of the Border Gateway Protocol (BGP)
routes against the contents of the specified AS-
match as-path <WORD 0-1027> lists. This field is used only for BGP routes and
ignored for all other route types. WORD 0-1027
specifies the list IDs of up to four AS-lists,
separated by a comma.
If configured, the switch matches the community
attribute of the BGP routes against the contents
of the specified community lists. This field is used
match community <WORD 0-1027> only for BGP routes and ignored for all other
route types. WORD 0-1027 specifies the list IDs of
up to four defined community lists, separated by
a comma.
When disabled, match community-exact results in
a match when the community attribute of the
BGP routes match any entry of any community-
list specified in match-community. When enabled,
match community-exact enable match-community-exact results in a match when
the community attribute of the BGP routes
matches all of the entries of all the community
lists specified in match-community. enable
enables match community-exact.
community-exact Matches community exactly, applicable for BGP
only, ignored in all other cases.
If configured, the switch matches the IP address
of the interface by which the RIP route was
learned against the contents of the specified
match interface <WORD 0-1027> prefix list. This field is used only for RIP routes
and ignored for all other route types. word 0-
1027 specifies the name of up to four defined
prefix lists, separated by a comma.
local-preference Matches the local preference, applicable to all
protocols.
If configured, the switch matches the metric of
match metric <0-65535> the incoming advertisement or existing route
against the specified value. If 0, this field is
ignored. 0-65535 The default is 0.
If configured, the switch matches the destination
network against the contents of the specified
match network <WORD 0-1027> prefix lists. WORD 0-1027 specifies the name of
up to four defined prefix lists, separated by a
comma.
If configured, matches the next-hop IP address of
the route against the contents of the specified
match next-hop <WORD 0-1027> prefix list. This field applies only to nonlocal
routes. WORD 0-1027 specifies the name of up to
four defined prefix lists, separated by a comma.
If configured, matches the protocol through
which the route is learned. WORD 0-40 is
match protocol <WORD 0-40> any|xxx, where xxx is local, OSPF, External BGP
(EBGP), Internal BGP (IBGP), RIP, Distance Vector
Multicast Routing Protocol (DVMRP), static, or any
combination, in a string length 0 to 40.
If configured, matches the next-hop IP address
for RIP routes and advertising router IDs for OSPF
match route-source <WORD 0-1027> routes against the contents of the specified prefix
list. This option is ignored for all other route
types. WORD 0-1027 specifies the name of up to
four defined prefix lists, separated by a comma.
Sets a specific route type to match (applies only
to OSPF routes).
match-route-type any|local|internal|external|external-1|external-2
{any|local|internal|external|external-
1|external-2} specifies OSPF routes of the specified type only
(External-1 or External-2). Any other value is
ignored.
Specifies a list of tags used during the match
match tag <WORD 0-256> criteria process. Contains one or more tag values.
WORD 0-256 is a value from 0 to 256.
match [vrf <WORD 0-32>] [vrfids <0- Sets a specific VRF to match (applies only to
255>] OSPF routes).
name <WORD 1-64> Renames a policy and changes the name field for
all sequence numbers under the given policy.
Specifies the action to take when a permit or
<permit|deny> deny policy is selected for a specific route. Permit
allows the route, deny ignores the route.
If configured, the switch adds the AS number of
the AS-list to the BGP routes that match this
policy. WORD 0-256 specifies the list ID of up to
set as-path <WORD 0-256> four defined AS-lists separated by a comma. Use
the no operator to delete the AS number: no
route-map <WORD 1-64> <1-65535> set as-
path
Sets the AS path mode. Prepend is the default
configuration. The switch prepends the AS
number of the AS-list specified in set-as-path to
set as-path-mode <tag|prepend> the old as-path attribute of the BGP routes that
match this policy. Use the no operator to delete
the AS number: no route-map <WORD 1-64>
<1-65535> set as-path-mode
Sets the tag automatically. Used for BGP routes
set automatic-tag enable only. Use the no operator to disable the tag: no
route-map <WORD 1-64> <1-65535> set
automatic-tag enable
If configured, the switch adds the community
number of the community list to the BGP routes
set community <WORD 0-256> that match this policy. WORD 0-256 specifies the
list ID of up to four defined community lists
separated by a comma.
Sets the community mode. additive-the switch
prepends the community number of the
community list specified in set-community to the
set community-mode
<unchanged|additive|none> old community path attribute of the BGP routes
that match this policy. none-the switch removes
the community path attribute of the BGP routes
that match this policy to the specified value.
If configured, the switch replaces the destination
set injectlist <WORD 0-1027> network of the route that matches this policy with
the contents of the specified prefix list. WORD 0-
1027 specifies one prefix list by name.
Setting the preference to a value greater than 0
specifies the route preference value to assign to
the routes that match this policy. This applies to
set ip preference <0-255> accept policies only. 0-255 is the range you can
assign to the routes. The default is 0. If the
default is configured, the global preference value
is used.
set local-preference <0-65535> A value used during the route decision process in
the BGP protocol. Applicable to BGP only.
If configured, sets the mask of the route that
set mask <A.B.C.D> matches this policy. This applies only to RIP
accept policies. A.B.C.D is a valid contiguous IP
mask.
If configured, sets the metric value for the route
while announcing a redistribution. The default is
set metric <0-65535> 0. If the default is configured, the original cost of
the route is advertised into OSPF; for RIP, the
original cost of the route or default-import-metric
is used.
If configured, sets the metric type for the routes
set metric-type {type1|type2} to announce into the OSPF domain that matches
this policy. The default is type 2. This field is
applicable only for OSPF announce policies.
Specifies the IP address of the next-hop router.
Ignored for Distance Vector Multicast Routing
set next-hop <A.B.C.D> Protocol (DVMRP) routes. Use the no operator to
disable set next-hop: no route-map <WORD 1-
64> <1-65535> set next-hop
set nssa-pbit enable Sets the not so stubby area (NSSA) translation P
bit. Applicable to OSPF announce policies only.
If configured, the switch changes the origin path
set origin {igp|egp|incomplete} attribute of the BGP routes that match this policy
to the specified value.
set origin-egp-as <0-65535> Indicates the remote autonomous system
number. Applicable to BGP only.
Sets the tag of the destination routing protocol. If
set tag <0-65535> not specified, the switch forwards the tag value in
the source routing protocol. A value of 0 indicates
that this parameter is not set.
The weight value for the routing table. For BGP,
this value overrides the weight configured
set weight <0-65535> through NetworkTableEntry, FilterListWeight, or
NeighborWeight. Used for BGP only. A value of 0
indicates that this parameter is not set.
Creates a route policy with a policy name and a
<WORD 1-64> <1-65535> sequence number. WORD 1-64 is the policy
name. 1-65535 is the sequence number.
enable Enables the route policy.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:route-map match
route-map match
Configure the route policy to accept BGP-learned routes.
Syntax
route-map <WORD 0-32> <1-10> match [vrf <WORD 0-32>] [vrfids <WORD 0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<WORD 0-32> Specify the name of the route policy to create or apply.
<1-10> Assign a sequence number to the policy.
vrf <WORD 0-32> Specify a VRF name from 032 characters for the match criteria.
vrfids <WORD 0-255> Specify a VRF ID from 0255 for the match criteria.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:route-map match condition
Syntax
route-map <WORD> <1-65535> match <match condition>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
165535 Specifies a sequence number for the policy.
Specifies one or more of the following as match criteria:as-path <ID from 01027>-
represents multiple as-list IDs as "2,4,5,6,7" community <ID from 01027>-represent
multiple community IDs as "2,4,5,6,7" community-exact enable interface <prefix-list from
match 01027> local-preference <02147483647> metric <065535> network <prefix-list
condition from 01027> next-hop <prefix-list from 01027> protocol <protocol from 040>-
Any|xxx, where xxx is local, rip, static, or any combination separated by a vertical line (|)
route-source <prefix-list from 01027> route-type <any|local|internal|external|external-
1|external-2> tag <tag from 0256> vrf <vrfName from 032> vrfids <ID from 0255>
WORD Specifies a name for the policy from 164 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:route-map match
extcommunity
Syntax
route-map <WORD 1-64> <1-65535> match extcommunity <extcommunity-list>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Filters incoming and outgoing updates based on communities. Specify the
community IDs from 01027. Reference multiple lists separated with a comma (,),
extcommunity-
list for example, 2,4,5,6,7. Use the no operator to remove this configuration. To
configure this option to the default value, use the default operator with the
command.
<WORD 1-64> Assigns a name to the policy from 164 characters.
<1-65535> Specifies a second index used to identify a specific policy within a route policy
group.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:route-map permit
route-map permit
Configure the route policy to accept routes.
Syntax
route-map <WORD 0-32> <1-10> permit
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<WORD 0-32> Specify the name of the route policy to create or apply.
<1-10> Assign a sequence number to the policy.
permit Permits the routes.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:route-map policyname
seqnumber
Syntax
route-map <WORD 0-32> <1-10>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Word <0-32> Specify the name of the route policy to create or apply.
<1-10> Assign a sequence number to the policy.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:route-map policy name seq
number permit
Syntax
route-map <policy-name> <seq_number> <permit|deny>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
policy-name Indicates the name of the specified policy with a string length of 1 to 64 characters.
seq_number Indicates the number of the specified policy in the range of 1 to 65535.
permit Permits the route.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:router bfd enable
Syntax
router bfd enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables BFD globally. The no and default versions of this command disable BFD globally.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:router bgp
router bgp
Access the router configuration mode to configure the Border
Syntax
router bgp
Default
None
Command mode
Global configuration mode
Syntax
router bgp [as-4-byte] [as-dot] [WORD<0-11>] enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
[as-4byte] Enables IP BGP as-4byte.
[as-dot] Enables IP BGP as-dot.
[WORD<011>] Autonomous system number.
enable Enables specified BGP variable
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:route-reflector enable
route-reflector enable
Enables the reflection of routes from IBGP neighbors.
Syntax
route-reflector enable
Default
The default value is enable.
Command mode
Global configuration mode
route-refresh
Enables or disables IP VPN Route Refresh. If enabled, a route refresh request received by a BGP speaker causes the speaker to
resend all route updates it contains in its database that are eligible for the peer that issues the request.
Syntax
route-refresh
Default
The default value is disable
Command mode
Global configuration mode
router-id
Configure OSPF so that MPLS can use the information from the OSPF unicast routing table to create and maintain routes within
the network. The router ID must be the same as the circuitless IP address. Specify the BGP router ID in IP address format. This
parameter only applies to VRF 0.
Syntax
router-id <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<A.B.C.D> Identifies the router IP address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:router isis
router isis
Set the configuration mode to config-isis for access to IS-IS configuration commands.
Syntax
router isis
Default
None
Command mode
Global configuration mode
Syntax
[no] [default] router isis enable
Default
The default is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
[no] Use the no option to disable IS-IS on the switch.
[default] Use the default option to disable IS-IS on the switch.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:router ospf enable
Syntax
router ospf enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
router ospf enable [ipv6- Enables OSPF routing on the Ethernet Routing Switch
enable] 8800/8600.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:router ospf ipv6-enable
Syntax
router ospf ipv6-enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
ipv6-enable Enables the OSPF for ipv6.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:router vrf
router vrf
Specify the VRF to configure.
Syntax
router vrf <vrf-name>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<vrf-name> Specifies the VRF.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:route-target both
route-target both
Configure one route target to define a single set of routes for import and export on the VRF.
Syntax
route-target both {<0-65535> <0-2147483647>|<A.B.C.D> <0-65535>}
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Defines one or more import or export policies that must be met for
routes received from remote PEs to be installed into the VRF routing
table and for routes from the VRF routing table to be redistributed to
remote PEs. Define the route target in one of the following formats:Type
{<0-65535> <0- 0-<AS number> <number> AS number is the assigned autonomous
2147483647>|<A.B.C.D>
<0-65535>} system (AS) number of the PE and number is an assigned 4-byte value.
Type 1-<ipaddr> <number> ipaddr is an IPv4 address in the assigned
prefix range of the PE and number is an assigned 2-byte value. Use the
no operator to later remove this configuration. To configure this option
to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:route-target import
route-target import
Configure separate route targets to define a set of routes for import or export on the VRF.
Syntax
route-target <import|export> {<0-65535> <0-2147483647>|<A.B.C.D> <0-65535>}
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Defines one or more import or export policies that must be met for
routes received from remote PEs to be installed into the VRF routing
table and for routes from the VRF routing table to be redistributed to
remote PEs. Define the route target in one of the following formats:Type
<0-65535> <0- 0-<AS number> <number> AS number is the assigned autonomous
2147483647>|<A.B.C.D>
<0-65535> system (AS) number of the PE and number is an assigned 4-byte value.
Type 1-<ipaddr> <number> ipaddr is an IPv4 address in the assigned
prefix range of the PE and number is an assigned 2-byte value. Use the
no operator to later remove this configuration. To configure this option
to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:routing
routing
You can enable or disable routing capabilities on specified switch ports. The specified port can be part of a routed VLAN, while
routing is disabled only on that port.
Syntax
routing enable
Default
The default setting for routing is enable.
Command mode
Gigabitethernet Interface configuration mode
Command parameters
Parameter Description
enable Sets the IP routing to enable.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:rsp-trace ingress-pkt-trace
enable
Syntax
[no] rsp-trace ingress-pkt-trace <slot/port> enable [<interval-value>]
Default
The default value is 1 second.
Command mode
Global configuration mode
Command parameters
Parameter Description
<slot/port> Specifies the port on which to enable Packet Tracing.
enable Enables the state of the ingress or egress Packet Tracing.
[<interval- Indicates the time interval for which the Packet Tracing is to remain enabled.
value>] <interval-value>specifies a value of 1, 10, 30, 60, 120, or 300 seconds.
[filter Display traces on only those RSP packets that you select. Instead of displaying all
<value>] 1024 records, you can preinitialize the trace records with the values to be filtered on.
no Disables ingress or egress Packet Tracing.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:save bootconfig
save bootconfig
Save the boot configuration file after accessing the boot monitor from the run-time environment to configure and manage the boot
process.
Syntax
save bootconfig
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
file Specifies the file name in one of the following formats for value:[a.b.c.d]: <file>
<word> peer/<file> /pcmcia/ <file> /flash/ <file> File is a string of 199 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:save config
save config
Save the running configuration to a file to retain the configuration settings.
Syntax
save config
save config [file <word 1-99>] [verbose] [standby <word 1-99>] [backup <word 1-99>] [mode
(cli|acli)]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
file Specifies the file name in one of the following formats for word: [a.b.c.d]: <file>
<word> peer/<file> /pcmcia/ <file> /flash/ <file> file is a string of 199 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:save config file
Syntax
save config [file <word>] [verbose] [standby <value>] [backup <word>] [mode (cli | acli)]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
file Specifies the file name in one of the following formats for value:[a.b.c.d]: <file>
<word> peer/<file> /pcmcia/ <file> /flash/ <file> File is a string of 199 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:save config file mode acli
Syntax
save config file <Word 1-99> mode acli
Default
None
Command mode
Privileged EXEC mode
Syntax
save config file <Word 1-99> mode cli
Default
None
Command mode
Privileged EXEC mode
Syntax
save config mode <cli|acli>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
cli Saves the configuration files in CLI format.
acli Saves the configuration files in ACLI format.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:save config standby
Syntax
save config standby Word<1-99>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
save standby <WORD 1-99> Save current configuration to a file.
Word <1-99> Specifies the file name in the range of 1 to 99 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:save trace
save trace
Save the trace file to the PCMCIA card for retrieval.
Syntax
save trace
save trace
Default
None
Command mode
Privileged EXEC mode
sffd enable
Enable the Single Fiber Fault Detection on the module to perform optimally on the network.
Syntax
sffd enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the Single Fiber Fault Detection as required.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show access-policy
show access-policy
Display access policy configuration information by MAC address, SNMP group, or policy name.
Syntax
show access-policy {by-mac | snmp-group | WORD<0-15>}
Default
None
Command mode
Interface configuration mode
Command parameters
Parameter Description
by-mac Displays access policy by-mac information.
snmp-group Displays access-policy SNMP group information.
WORD<0-15> Displays information for the specified access policy name.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show autotopology nnm-
table
Syntax
show autotopology nmm-table
Default
None
Command mode
Interface configuration mode
show banner
Display the ACLI logon banner.
Syntax
show banner
Default
None
Command mode
Privileged EXEC mode
Syntax
show basic config
Default
None
Command mode
Privileged EXEC mode
Syntax
show bgp ipv6 aggregates [WORD<1-256>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<WORD<1-256>> Specifies the IPv6 prefix and mask length.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show bgp ipv6 imported-
routes
Syntax
show bgp ipv6 imported-routes [WORD<1-256>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<prefix/len> Shows paths with this IPv6 prefix/length.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show bgp ipv6 neighbors
Syntax
show bgp ipv6 neighbors [WORD<1-256>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
WORD<1-256> Specifies the IPv6 prefix and mask length.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show bgp ipv6 networks
Syntax
show bgp ipv6 networks [WORD<1-256>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
WORD<1-256> Specifies the IPv6 prefix and mask length.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show bgp ipv6 redistributed-
routes
Syntax
show bgp ipv6 redistributed-routes
Default
None
Command mode
Privileged EXEC mode
Syntax
show bgp ipv6 route [community <enable|disable>] [ipv6 WORD<1-256>] [WORD<1-256>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
community <enable|disable> Enables or disables the display of community attributes.
ipv6 WORD<1-256> Specifies an Iv6P address.
WORD<1-256> Specifies the IPv6 prefix and mask length.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show boot config
Syntax
show boot config
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
bootp Displays the bootp configuration.
choice Displays the current boot configuration choices.
cli Displays the current cli configuration.
flags Displays the current flag settings.
general Displays system information.
host Displays the current host configuration.
master Displays the current SF/CPU slot set as master and the settings for the delay and
multicast command.
mezz-image Displays the mezzanine image.
net Displays the current configuration of the SF/CPU network ports.
running- Displays the current boot configuration. verbose includes all possible information. If
config you omit verbose, only the values that were changed from their default settings
[verbose] appear.
sio Displays the current configuration of the SF/CPU serial ports.
tz Displays the current configuration of the switch time zone.
wlan Displays wireless LAN information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show boot config choice
Syntax
show boot config choice
Default
None
Command mode
Global configuration mode
Syntax
shoe boot config flags
Default
Command mode
Privileged EXEC mode
Syntax
show boot config master
Default
None
Command mode
Privileged EXEC mode
show brouter
Display the brouter ports on the Ethernet Routing Switch 8800/8600.
Syntax
show brouter <1-4094>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-4094> Specifies the VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show cfm ethertype
Syntax
show cfm ethertype
Default
None
Command mode
Global configuration mode
Syntax
show cfm maintenance-association
Default
None
Command mode
Global configuration mode
Syntax
show cfm maintenance-domain
Default
None
Command mode
Global configuration mode
Syntax
show cfm maintenance-endpoint
Default
None
Command mode
Global configuration mode
Syntax
show cli info
Default
None
Command mode
Privileged EXEC mode
show clilog
Ensure the clilog information is accurate.
Syntax
show clilog
Default
None
Command mode
Privileged EXEC mode
Syntax
show clilog file [tail] [grep <WORD 1-256>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
tail Shows the last results first.
grep <WORD Performs a string search in the log file. <WORD 1-256> is the string, of up to 256
1-256> characters in length, to match.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show cli password
Syntax
show cli password
Default
None
Command mode
Privileged EXEC mode
show clock
Syntax
show clock
Default
None
Command mode
Privileged EXEC mode
show eapol
Display overall system EAPOL information as well as statistics to manage network performance.
Syntax
show eapol {auth-diags interface <interface-type> | auth-stats interface <interface-type>
| multihost-session-stats interface <interface-type> | port [<slot/port> | <interface-
type>] | session-stats interface <interface-type> | status interface <interface-type> |
system
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
auth-diags interface <interface- Displays the port EAPOL authenticator diagnostics for the
type> specified interface type.
auth-stats interface <interface- Displays the port EAPOL authenticator statistics for the
type> specified interface type.
multihost-session-stats Displays the manage mode parameters for the specified
interface <interface-type> interface type.
port [<slot/port> | <interface- Displays EAPOL information for the specified port or
type>] interface type.
session-stats interface Displays the port EAPOL authenticator session statistics
<interface-type> for the specified interface type.
status interface <interface- Displays the port EAPOL operation statistics for the
type> specified interface type.
system Displays the current EAPOL setting on the switch.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show fdb-filter
show fdb-filter
Display global fdb-filter information.
Syntax
show fdb-filter
Default
None
Command mode
Privileged EXEC mode
Syntax
show filter acl [<1-4096>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show filter acl ace [<1-4096>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
ace-id Specifies a unique identifier (in the range 1 through 1000) for this ACE entry.
acl-id Specifies a unique identifier (in the range 1 through 4096) for this ACL entry.
<1-4096> Specifies an ACL ID from 1 to 4096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show filter acl action
Syntax
show filter acl action [<1-4096>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4096> Specifies an ACL ID from 1 to 4096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show filter acl advanced
Syntax
show filter acl advanced [<1-4096>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4096> Specifies an ACL ID from 1 to 4096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show filter acl arp
Syntax
show filter acl arp [<1-4096>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4096> Specifies an ACL ID from 1 to 4096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show filter acl config
Syntax
show filter acl config [<1-4096>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4096> Specifies an ACL ID from 14096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show filter acl debug
Syntax
show filter acl debug [<1-4096>] [<1-1000>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4096> Specifies the ACL ID from 1 to 4096.
<1-1000> Specifies the ACE ID from 1 to 1000.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show filter acl ethernet
Syntax
show filter acl ethernet [<1-4096>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-4096> Specifies an ACL ID from 1 to 4096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show filter acl ip
Syntax
show filter acl ip [<1-4096>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-4096> Specifies an ACL ID from 1 to 4096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show filter acl ipv6
Syntax
show filter acl ipv6 [<1-4096>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4096> Specifies an ACL ID from 1 to 4096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show filter acl protocol
Syntax
show filter acl protocol [<1-4096>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4096> Specifies an ACL ID from 1 to 4096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show filter acl statistics port
Syntax
show filter acl statistics port[<1-4096>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4096> Specifies an ACL ID from 1 to 4096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show filter act
Syntax
show filter act [<1-4096>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
act-id Specifies a unique identifier (in the range 1 through 4096) for this ACT entry.
<1-4096> Specifies the ACT ID in the range of 1 to 4096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show filter act-pattern
Syntax
show filter act-pattern [<1-4096>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
act-id Specifies a unique identifier (in the range 1 through 4096) for this ACT entry.
<1-4096> Specifies the ACT ID in the range of 1 to 4096.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show fulltech
show fulltech
Display the full technical details of all the settings on the switch.
Syntax
show fulltech [file WORD<1-4096>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
file WORD<1-4096> Specifies a file name for where to store this information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ha-state
show ha-state
Display the current state of high availability on your CPU.
Syntax
show ha-state
Default
None
Command mode
Privileged EXEC mode
show history
Display the history of commands.
Syntax
show history
Default
None
Command mode
Privileged EXEC mode
show hosts
Query the DNS host for information about host addresses. You can enter either a hostname or an IP address.
Syntax
show hosts <word>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Specifies one of the following:the name of the host DNS server as a string of 0255
word characters. the IP address of the host DNS server in a.b.c.d format. the IPv6 address of
the host DNS server in hexadecimal format (string length 046).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics
Syntax
show interfaces atm statistics [<1-4094>][portlist]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics ds3fecurrent
Syntax
show interfaces atm statistics ds3fecurrent [<1-4094>][portlist]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics ds3feinterval
Syntax
show interfaces atm statistics ds3feinterval <1-96> [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-96> Indicates the interval.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics ds3fetotal
Syntax
show interfaces atm statistics ds3fetotal [<1-4094>] [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics ds3necurrent
Syntax
show interfaces atm statistics ds3necurrent [<1-4094>] [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics ds3neinterval
Syntax
show interfaces atm statistics ds3neinterval [<1-96>] [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-96> Indicates the interval.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics ds3netotal
Syntax
show interfaces atm statistics ds3netotal [<1-4094>] [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics felinecurrent
Syntax
show interfaces atm statistics felinecurrent [<1-4094>] [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics felineinterval
Syntax
show interfaces atm statistics felineinterval <1-96> [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-96> Indicates the interval.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics fepathcurrent
Syntax
show interfaces atm statistics fepathcurrent [>1-4094>] [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics fepathinterval
Syntax
show interfaces atm statistics fepathinterval <1-96> [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-96> Indicates the interval.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics linecurrent
Syntax
show interfaces atm statistics linecurrent [<1-4094>] [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics lineinterval
Syntax
show interfaces atm statistics lineinterval <1-96> [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-96> Indicates the interval.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics pathcurrent
Syntax
show interfaces atm statistics pathcurrent [<1-4094>] [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics pathinterval
Syntax
show interfaces atm statistics pathinterval <1-96> [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-96> Indicates the interval.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics sectioncurrent
Syntax
show interfaces atm statistics sectioncurrent [<1-4094>] [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics sectioninterval
Syntax
show interfaces atm statistics sectioninterval <1-96> [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-96> Indicates the interval.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces atm
statistics sonetmediumtbl
Syntax
show interfaces atm statistics sonetmediumtbl [<1-4094>] [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN.
<portList> Indicates the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces dhcp-relay
Syntax
show interfaces FastEthernet statistics dhcp-relay[<vrf>][<vrfids>][<portList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[<vrf>] Specifies a VRF instance by VRF name.
[<vrfids>] The ID of the VRF and is an integer between 0 and 255.
[<portList>] Displays all statistics by port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces error ospf
Syntax
show interfaces [fastEthernet|GigabitEthernet] error ospf [<portList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<portList> is the either port or slot number or a range of ports.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces
FastEthernet error
Syntax
show interfaces FastEthernet error
Default
None
Command mode
Privileged EXEC mode
Syntax
show interfaces FastEthernet statistics
Default
None
Command mode
Privileged EXEC mode
Syntax
show interfaces gigabitEthernet
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Displays port bandwidth limit commands. <14094>
bandwidth-limit [<14094> |
<slot/port>] specifies the VLAN ID in the range of 1 to 4094.
<slot/port> specifies the port list.
Displays port configuration information. <14094>
config [<14094> | <slot/port>] specifies the VLAN ID in the range of 1 to 4094.
<slot/port> specifies the port list.
Displays port packet cp-limit commands. <14094>
cp-limit [<14094> |
<slot/port>] specifies the VLAN ID in the range of 1 to 4094.
<slot/port> specifies the port list.
error collision <slot/port> Displays port collision error information. <slot/port>
specifies the port list.
error ospf <slot/port> Displays ports OSPF error information. <slot/port>
specifies the port list.
error verbose <slot/port> Displays general port error information. <slot/port>
specifies the port list.
Displays port ext-cp-limit information. <14094>
ext-cp-limit [<14094> |
<slot/port>] specifies the VLAN ID in the range of 1 to 4094.
<slot/port> specifies the port list.
Displays the port fdb-entry database. <14094>
fdb-entry [<14094> |
<slot/port>] specifies the VLAN ID in the range of 1 to 4094.
<slot/port> specifies the port list.
Displays high secure port information. <14094>
high-secure [<14094> |
<slot/port>] specifies the VLAN ID in the range of 1 to 4094.
<slot/port> specifies the port list.
Displays general port information. <14094> specifies
interface [<14094> |
<slot/port>] the VLAN ID in the range of 1 to 4094. <slot/port>
specifies the port list.
Displays port l1-config information. <14094> specifies
l1-config [<14094> |
the VLAN ID in the range of 1 to 4094. <slot/port>
<slot/port>]
specifies the port list.
Displays port limit-fdb-learning information. <14094>
limit-fdb-learning [<14094> |
<slot/port>] specifies the VLAN ID in the range of 1 to 4094.
<slot/port> specifies the port list.
Displays port loop-detected information. <14094>
loop-detected [<14094> |
<slot/port>] specifies the VLAN ID in the range of 1 to 4094.
<slot/port> specifies the port list.
Displays the port unknown-mac-discard information. <1
mac-security [<14094> |
<slot/port>] 4094> specifies the VLAN ID in the range of 1 to 4094.
<slot/port> specifies the port list.
Displays IPv6 port mld information. <14094> specifies
mld [<14094> | <slot/port>] the VLAN ID in the range of 1 to 4094. <slot/port>
specifies the port list.
Displays port names. <14094> specifies the VLAN ID in
name [<14094> | <slot/port>] the range of 1 to 4094. <slot/port> specifies the port
list.
Displays ospf interfaces information for ports. <14094>
ospf [<14094> | <slot/port>] specifies the VLAN ID in the range of 1 to 4094.
<slot/port> specifies the port list.
Displays port OSPFv3 information. <14094> specifies
ospfv3 [<14094> | <slot/port>] the VLAN ID in the range of 1 to 4094. <slot/port>
specifies the port list.
Displays port rate limit commands. <14094> specifies
rate-limit [<14094> |
<slot/port>] the VLAN ID in the range of 1 to 4094. <slot/port>
specifies the port list.
Displays the shape or egress-rate-limit on ports (applies
shape <slot/port> to R-module ports only). <slot/port> specifies the port
list.
slpp <slot/port> Displays port SLPP information. <slot/port> specifies the
port list.
Displays port state information. <14094> specifies the
state [<14094> | <slot/port>] VLAN ID in the range of 1 to 4094. <slot/port> specifies
the port list.
statistics [dhcp-relay | egress-
queues | lacp | rmon | stg | Displays port statistics.
verbose | <slot/port>]
Displays port VLAN information. <14094> specifies the
vlan [<14094> | <slot/port>] VLAN ID in the range of 1 to 4094. <slot/port> specifies
the port list.
vrfs [vrf WORD<032> | vrfids Displays PORT-VRF association information. <slot/port>
WORD<0255> | <slot/port>] specifies the port list.
{slot/port[-slot/port][,...]} Displays port information for a specified <slot/port> list.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces loopback
Syntax
show interfaces loopback vrf <WORD 0-32> vrfids <WORD 0-255>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf <WORD Displays the loopback information for the associated VRF name. <WORD 0-32>
0-32> specifies the VRF name in the range of 0 to 32 characters.
vrfids Displays the loopback configuration for the specified VRF IDs. <WORD 0-255>
<WORD 0-
255> specifies the VRF IDs in the range of 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces statistics
Syntax
show interfaces FastEthernet statistics bridging[<portList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[<portList>] Displays all statistics by port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces statistics
dhcp-relay
Syntax
show interfaces [interface-type] statistics dhcp-relay [slot/port] [vrf <WORD 0-32>]
[vrfids <0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[interface-type] [interface-
id] The type of interface and the ID of the interface.
[vrf <WORD 0-32>] The name of the VRF.
[vrfids <0-255>] The ID of the VRF and is an integer. The range is are 0
255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces statistics
egress-queues
Syntax
show interfaces FastEthernet statistics egress-queues<0-63> [<portList>] [verbose]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[<portList>] Displays all queue statistics by port.
<0-63> Indicates the transmitted queue template identifier.
Displays the queues with both nonzero and zero allocation. Otherwise, only queues
[verbose] with nonzero allocations are shown. You can also use this option for debugging
purposes because it can signal a configuration problem if the queues with zero
allocation have packet drops.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces statistics
ipvpn
Syntax
show interfaces FastEthernet statistics ipvpn[<vrf>][<vrfids>][<portList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[<vrf>] Specifies a VRF instance by VRF name.
[<vrfids>] The ID of the VRF and is an integer between 0 and 255.
[<portList>] Displays all statistics by port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces statistics
lacp
Syntax
show interfaces FastEthernet statistics lacp[<portList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[<portList>] Displays all statistics by port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces statistics
rmon
Syntax
show interfaces FastEthernet statistics rmon[<portList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[<portList>] Displays all statistics by port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces statistics stg
Syntax
show interfaces FastEthernet statistics stg[<portList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[<portList>] Displays all statistics by port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show interfaces statistics
verbose
Syntax
show interfaces FastEthernet statistics verbose
Default
None
Command mode
Privileged EXEC mode
Syntax
show interfaces vlan [<1-4094> | arp | autolearn-mac | dhcp-relay | igmp | igmp-mrdisc |
ip | manual-edit-mac | nlb-mode | vlan-bysrcmac | vrfs]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Displays information on the specified VLAN. <1
<14094> 4094> specifies the VLAN ID in the range of 1 to
4094.
Displays VLAN Address Resolution Protocol (ARP)
arp <14094> information. <14094> specifies the VLAN ID in the
range of 1 to 4094.
autolearn-mac Displays bridging autolearn MAC address information.
dhcp-relay <14094> Displays VLAN DHCP information. <14094>
specifies the VLAN ID in the range of 1 to 4094.
igmp <14094> Displays VLAN IP IGMP information. <14094>
specifies the VLAN ID in the range of 1 to 4094.
Displays VLAN IP IGMP multicast route discovery
igmp-mrdisc <14094> information. <14094> specifies the VLAN ID in the
range of 1 to 4094.
ip [<14094> | vrf WORD<032> | Displays VLAN IP information. <14094> specifies
vrfids WORD<0255>] the VLAN ID in the range of 1 to 4094.
manual-edit-mac Displays bridging manual edit MAC address
information.
Displays Network Load Balancer (NLB) mode
nlb-mode <14094> information. <14094> specifies the VLAN ID in the
range of 1 to 4094.
vlan-bysrcmac Displays VLAN by source MAC information.
vrfs [<14094> | vrf WORD<032> | Displays VLAN-VRF association information.
vrfids WORD<0255> | <slot/port> |
<slot/port>] <slot/port> specifies the port list.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip
show ip
Use the following command to view other IP show commands that you can us
Syntax
show ip ?
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip access-list extended [Word<1-64>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
1-64 Optionally, specifies the name of an extended ACL, up to 64 characters, to include in the
command results. If you do not specify a name, the command results include all ACLs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip arp
show ip arp
View and confirm the ARP configuration on the switch.
Syntax
show ip arp
Default
None
Command mode
Global configuration mode
Syntax
show ip arp inspection interface [<interface-type>] [<port>]
Default
None
Command mode
Interface configuration mode
Command parameters
Parameter Description
<interface Identifies the type of interface that displays port ARP inspection status. Values are
type> FastEthernet and GigabitEthernet.
<port> Specifies the port number for a single port or range of ports, entered as {slot/port[-
slot/port][,...]}.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip arp inspection vlan
Syntax
show ip arp inspection vlan
Default
None
Command mode
User EXEC mode
Syntax
show ip arp interface <interface-type> <interface-id>
Default
None
Command mode
Privileged EXEC mode/Global configuration mode
Command parameters
Parameter Description
interface-id ID of the interface.
interface-type Type of interface, either a port or a VLAN.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip arp -s
show ip arp -s
Show ARP information to view the configuration information in theARP table.
Syntax
show ip arp [<A.B.C.D>] [-s <A.B.C.D> <A.B.C.D>] [vrf <WORD 0-32>] [vrfids <0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<A.B.C.D> The specific network IP address for the table.
-s <A.B.C.D> <A.B.C.D> The specific subnet for the table.
vrf <WORD 0-32> The name of the VRF.
vrfids <0-255> The VRF ID in the range of 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip arp static-mcastmac
Syntax
show ip arp static-mcastmac [-s <IP/subnet value> [vrf <vrf name>] [vrfids <vrf ID>]
[<A.B.C.D]
Default
None
Command mode
Privileged EXEC mode
show ip as-list
Display global AS path list information or for a specific VRF.
Syntax
show ip as-list [<1-1024> | vrf WORD<0-32> | vrfids WORD<0-255>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-1024> Specifies the AS-path list entry.
vrf WORD<0-32> Specifies a VRF instance by name.
vrfids WORD<0-255> Specifies a range of VRFs by ID number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bfd
show ip bfd
View BFD information on the switch.
Syntax
show ip bfd
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip bfd interfaces [gigabitEthernet <slot/port> | vlan <1-4094>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
gigabitEthernet <slot/port> Specifies the GigabitEthernet interface by slot and port number.
vlan <1-4094> Specifies the VLAN by ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bfd neighbors
Syntax
show ip bfd neighbors
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip bfd neighbors next-hop <A.B.C.D>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<A.B.C.D> Specifies the ip address of the next hop to view the information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bfd stats
Syntax
show ip bfd stats
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip bgp aggregates [<prefix/len>] [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<prefix/len> Specifies the IP address and the mask length (the length can be 0 to 32).
vrf <WORD 0-16> Specifies a VRF instance by name.
vrfids <WORD 0-255> Specifies a range of VRFs by ID number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bgp cidr-only
Syntax
show ip bgp cidr-only [<prefix/len>] [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<prefix/len> Specifies an exact match of the prefix. This is an IP address and an integer value
between 0 and 32 in the format a.b.c.d/xx.
vrf <WORD 0-
16> Specifies a VRF instance by name.
vrfids <WORD
0-255> Specifies a range of VRFs by ID number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bgp conf
Syntax
show ip bgp conf [vrf WORD<0-64> | vrfids WORD<0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf WORD<0-64> Specifies a VRF instance by name.
vrfids WORD<0-255> Specifies a range of VRFs by ID number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bgp confederation
Syntax
show ip bgp confederation
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip bgp dampened-paths <A.B.C.D> [<prefix/len>] [longer-prefixes] [vrf <WORD 0-16>]
[vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<prefix/len> Shows paths with this prefix. The prefix is the IP address and exact mask length
(must be an integer value between 0 and 32).
longer- Shows long prefixes. The longer-prefixes indicate the mask length from any specified
prefixes prefix to 32 (for example, show from prefix a.b.c.d/len to a.b.c./32).
vrf <WORD
0-16> Specifies a VRF instance by name.
vrfids
<WORD 0- Specifies a range of VRFs by ID number.
255>
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bgp flap-damp-
config
Syntax
show ip bgp flap-damp-config [<prefix/len>] [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[<prefix/len>] Exact match the prefix {a,b,c,d/len}.
vrf <WORD 0-16> Displays BGP configuration for a particular VRF.
vrfids <WORD 0-255> Specifies the VRF ID in the range of 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bgp imported-
routes
Syntax
show ip bgp imported-routes [<prefix/len>] [longer-prefixes] [vrf <WORD 0-16>] [vrfids
<WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<prefix/len> Shows paths with this prefix. The prefix is the IP address and exact mask length
(must be an integer value between 0 and 32).
longer- Shows long prefixes. The longer-prefixes indicate the mask length from any specified
prefixes prefix to 32 (for example, show from prefix a.b.c.d/len to a.b.c./32).
vrf <WORD
0-16> Specifies a VRF instance by name.
vrfids
<WORD 0- Specifies a range of VRFs by ID number.
255>
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bgp neighbors
Syntax
show ip bgp neighbors [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf <WORD 0-16> Specifies a VRF instance by name.
vrfids <0-255> Specifies a range of VRFs by ID number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bgp neighbors
A.B.C.D
Syntax
show ip bgp neighbors <A.B.C.D> advertised-routes [<prefix/len>] [longer-prefixes] [vrf
<WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
advertised-routes Displays information about BGP peer advertised routes.
routes Displays information about BGP peer routes.
stats Displays statistics information for BGP peers.
vpnv4 Displays information about IP VPN BGP peers.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bgp networks
Syntax
show ip bgp networks [<prefix/len>] [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<prefix/len> Shows networks with this prefix. The prefix is the IP address and exact mask length
(must be an integer value between 0 and 32).
vrf <WORD
0-16> Specifies a VRF instance by name.
vrfids
<WORD 0- Specifies a range of VRFs by ID number.
255>
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bgp peer-group
Syntax
show ip bgp peer-group [<WORD 1-1536>] [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<WORD 1-1536> Specifies the name of the peer group.
vrf <WORD 0-16> Specifies a VRF instance by name.
vrfids <WORD 0-255> Specifies a range of VRFs by ID number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bgp redistributed-
routes
Syntax
show ip bgp redistributed-routes [<prefix/len>] [vrf WORD<0-64>] [vrfids WORD<0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<prefix/len> Specifies the IP address and the mask length (the length can be 0 to 32).
vrf WORD<0-64> Specifies a VRF instance by name.
vrfids WORD<0-255> Specifies a range of VRFs by ID number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bgp route
Syntax
show ip bgp route [<prefix/len>] [longer-prefixes] [community <enable|disable>] [ip
<A.B.C.D>] [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<prefix/len> Shows paths with this prefix. The prefix is the IP address and exact mask
length (must be an integer value between 0 and 32).
community
<enable|disable> Enables or disables the display of community attributes.
ip <A.B.C.D> Specifies an IP address.
longer-prefixes Shows long prefixes. The longer-prefixes indicate the mask length from any
specified prefix to 32 (for example, show from prefix a.b.c.d/len to a.b.c./32).
vrf <WORD 0-16> Specifies a VRF instance by name.
vrfids <WORD 0-
255> Specifies a range of VRFs by ID number.
<prefix/len> Displays exact prefix {a.b.c.d/len.}
community Displays community attributes.
ip Specifies the IP address.
longer-prefixes Displays all the more specified routes.
vrf Displays BGP configuration for a particular VRF.
vrfids <Word 0-
255> Specifies the VRF ID in the range of 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bgp stats
Syntax
show ip bgp stats [vrf WORD<0-64>] [vrfids WORD<0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf WORD<0-64> Specifies a VRF instance by name.
vrfids WORD<0-255> Specifies a range of VRFs by ID number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bgp summary
Syntax
show ip bgp summary [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf <value> Specifies a VRF instance by name.
vrfids <value> Specifies a range of VRFs by ID number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip bgp vpnv4
Syntax
show ip bgp vpnv4 [<prefix/len>] [longer-prefixes] [community] [ext-community] [vrf <WORD
0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<prefix/len> Shows paths with this prefix. The prefix is the IP address and exact mask length
(must be an integer value between 0 and 32).
longer- Shows long prefixes. The longer-prefixes indicate the mask length from any specified
prefixes prefix to 32 (for example, show from prefix a.b.c.d/len to a.b.c./32).
community Enables the display of community attributes.
ext-
community Enables the display of extended community attributes.
ip Specifies the IP address.
vrf <WORD
0-16> Specifies a VRF instance by name.
vrfids
<WORD 0- Specifies a range of VRFs by ID number.
255>
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip community-list
show ip community-list
Display IP community lists that specify permitted routes by using their BGP community.
Syntax
show ip community-list <1-1024> [vrf WORD<0-32> | vrfids WORD<0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-1024> Creates the specified community list entry.<1-1024> specifies the list id.
vrf WORD<0-32> Specifies a VRF instance by name.
vrfids WORD<0-255> Specifies a range of VRFs by ID number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip dhcp-relay
show ip dhcp-relay
Display relay information to show relay information about DHCP routes and counters.
Syntax
show ip dhcp-relay [counters | fwd-path | interface] [vrf <WORD 0-32>] [vrfids <0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
counters Displays information about DHCP relay forward paths.
fwd-path Displays information about DHCP relay counters.
interface Selects the interface.
vrf <WORD 0-32> The name of the VRF.
vrfids <0-255> The ID of the VRF. The value is an integer in the range of 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip dhcp snooping
Syntax
show ip dhcp snooping
Default
None
Command mode
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip dhcp snooping
binding
Syntax
show ip dhcp snooping binding
Default
None
Command mode
User EXEC mode
Syntax
show ip dhcp snooping interface [<interface-type>] [<portlist>]
Default
None
Command mode
User EXEC mode
Command parameters
Parameter Description
[<interface-
type>] Specifies the port type (for example, FastEthernet).
Syntax
show ip dhcp snooping vlan
Default
None
Command mode
User EXEC mode
Syntax
show ip directed-broadcast interface [GigbitEthernet <slot/port>]]
Default
The default is enabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
GigbitEthernet Specifies the Gigabit Ethernet slot and port number that you want to display
<slot/port> the directed broadcast information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip dns
show ip dns
View the DNS client system status.
Syntax
show ip dns
Default
None
Command mode
Global configuration mode
show ip dvmrp
Display information about the general Distance Vector Multicast Routing Protocol (DVMRP) group.
Syntax
show ip dvmrp
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip dvmrp interface [fastethernet <slot/port>] [gigabitethernet <slot/port>] [pos
<slot/port>] [vlan <vlan_id>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip dvmrp neighbor
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip dvmrp next-hop
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip dvmrp route
Default
None
Command mode
Privileged EXEC mode
show ip ecmp
Display the prefix list of routes with number of ECMP paths.
Syntax
show ip ecmp pathlist-1 vrf <WORD 0-32> vrfids <WORD 0-255>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
pathlist-1 Displays prefix list of routes with 1 ecmp path.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip extcommunity-list
show ip extcommunity-list
Display IP extended community lists that specify permitted routes by using their BGP community.
Syntax
show ip extcommunity-list <1-1024> [vrf WORD<0-32> | vrfids WORD<0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-1024> Creates the specified community list entry.<1-1024> specifies the list id.
vrf WORD<0-32> Specifies a VRF instance by name.
vrfids WORD<0-255> Specifies a range of VRFs by ID number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip forward-protocol
udp
Syntax
show ip forward-protocol udp [vrf <WORD 0-32>] [vrfids <0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
[vrf <WORD 0-32>] The name of the VRF.
[vrfids <0-255>] The ID of the VRF. The value is an integer between 0 and 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip forward-protocol
udp portfwd
Syntax
show ip forward-protocol udp portfwd [vrf <WORD 0-32>] [vrfids <0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Adds a UDP protocol port to the specified port forwarding list. 1-65535 is a UDP protocol
<1- port in the range of 1 to 65535. A.B.C.D is an IP address in a.b.c.d format. Use the no
65535> operator to remove a protocol port forwarding entry and IP address from the list: no ip
<A.B.C.D> forward-protocol udp portfwd <1-65535> <A.B.C.D> To set this option to the default
value, use the default operator with this command.
[vrf
<WORD 0- The name of the VRF.
32>]
[vrfids
<0-255>] The ID of VRF and is an integer between 0 and 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip forward-protocol
udp portfwdlist
Syntax
show ip forward-protocol udp portfwdlist [vrf <WORD 0-32>] [vrfids <0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<WORD 0-15> Name of the UDP port forwarding list. WORD 0-15 is an alphabetic string.
[vrf <WORD 0-32>] The name of the VRF.
[vrfids <0-255>] The ID of the VRF and is an integer in the range of 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip igmp access
Syntax
show ip igmp access [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip igmp cache [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip igmp group
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip igmp igap
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip igmp igap counters [vlan <value>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vlan <value> Indicates the ID number of the VLAN. The value ranges from 1 to 4094.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip igmp igap group
Syntax
show ip igmp igap group [count] [member-subnet <A.B.C.D/X or A.B.C.D/X.X.X.X or default>]
[group <A.B.C.D>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
count Shows the number of entries in the IGAP group.
group Indicates the IP address of the group.
member-subnet Indicates the IP address and network mask of the IGAP group.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip igmp interface
Syntax
show ip igmp interface [fastethernet <slot/port>] [gigabitethernet <slot/port>] [pos
<slot/port>] [vlan <slot/port>] [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip igmp mrdisc [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip igmp mrdisc neighbors [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip igmp router-alert [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip igmp sender [count] [group <IP address>] [member-subnet <default|IP address/mask>]
[vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip igmp snooping [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip igmp snoop-trace [source <IP address>] [group <IP address>] [vrf Word<0-16>]
[vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip igmp ssm [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip igmp ssm-map [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip igmp static [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip igmp stream-limit interface <fastethernet|gigabitethernet>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Specifies the type of interface to include in the output. The
fastethernet|gigabitethernet results display all ports using stream limitation on the selected
interface type.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip igmp sys
Syntax
show ip igmp sys [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
vrf Word <0-16> Specifies the name of the VRF with a string length of 0 to 16 characters.
vrfids Word <0-255> Sets the VRF ID in the range of 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip interface
show ip interface
Displays the IP interface information.
Syntax
show ip interface [gigabitethernet <1-4094> <slot/port>] [vrf WORD<0-64>] [vrfids <WORD 0-
255>]
Default
None
Command mode
Configuration Mode
Command parameters
Parameter Description
gigabitethernet <14094> Specifies the Gigabit Ethernet interface by VLAN ID or slot
<slot/port> and port number
vrf WORD<0-64> Specifies a VRF instance by VRF name.
vrfids WORD<0-255> Specifies a VRF instance by VRF number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ipfix
show ip ipfix
You can display flow entries using the ACLI framework. Because the flow database is large, the sorting functionality remains
simple. The response time can be slow for sorted displays.
Syntax
show ip ipfix
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
collector [<slotList>] Shows collector information.
exporter [<slots>] Shows exporter information.
export [<slots>] Shows exporter statistics.
flows <slots> [source- Displays IPFIX flows for a given slot. source-addr-
addr {=|!=|<=|>=} oper{=|!=|<=|>=} and ip addr {A.B.C.D}; for example,
<A.B.C.D>] [dest-addr {<=A.B.C.D}. dest-addr-oper{=|!=|<=|>=} and ip addr
{=|!=|<=|>=} <A.B.C.D>] {A.B.C.D}; for example, {>=A.B.C.D}. port-oper{=|!=|<=|>=}
[port {=|!=|<=|>=}
<slot/port>] [vlan and port{slot/port}; for example, {=a/b}. vlan-oper{=|!=|<=|>=}
{=|!=|<=|>=} <0-4095>] and vlan{04095}; for example, {!=a}. protocol-
[protocol {=|!=|<=|>=} oper{=|!=|<=|>=} and protocol {0255}; for example, {>=a}.
<0-255>] [TCP-UDP-src- The mapping values for some of the protocol types are icmp:1,
port {=|!=|<=|>=} <0- tcp:6, udp:17, ipsecesp:50, ipsecah:51, ospf:89, vrrp:112,
65535>] [TCP-UDP-dest- snmp:254, undefined:256. TCP-UDP-src-port-oper{=|!=|<=|>=}
port {=|!=|<=|>=} <0- and port {065535}; for example, {>=a}. TCP-UDP-dest-port-
65535>] [byte-count
{=|!=|<=|>=} <0- oper{=|!=|<=|>=} and port {065535}; for example, {>=a}.
4294967295>] [pkt-count byte-count-oper{=|!=|<=|>=} and byte-count {0-4294967295}.
{=|!=|<=|>=} <0- For example, {>=a}. pkt-count-oper{=|!=|<=|>=} and pkt-count
4294967295>] [TOS {04294967295}; for example, {>=a}. TOS = oper{=|!=|<=|>=}
{=|!=|<=|>=} <0-255>] and TOS{0-255},e.g {>=a} first-pkt-time-oper{=|!=|<=|>=} and
[first-pkt-time time {MMddyyyyhhmmss}; for example, {>=a}. last-pkt-time-
{=|!=|<=|>=} oper{=|!=|<=|>=} and time {MMddyyyyhhmmss}; for example,
<MMddyyyyhhmmss>] [last- {>=a}. monitor-true|false. When monitor is set to true, you can
pkt-time {=|!=|<=|>=}
<MMddyyyyhhmmss>][monitor monitor the 10 flows (by byte count) by default. You can monitor
<true|false>] [numFlows more flows by setting the numFlows option. The maximum number
<1-100>] of flows that can be monitored is 100. numFlows-from 1100.
hash-statistics
[<slots>] Shows hash statistics.
interface [<interface-
type>] [<interface-id>] Shows IPFIX interface information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ipfix export
Syntax
show ip ipfix export [<slots>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[<slots>] Indicates a slot or range of slots for which you want to view statistics.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ipfix hash-statistics
Syntax
show ip ipfix hash-statistics [<slots>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[<slots>] Indicates a slot or range of slots for which you want to view statistics.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ipvpn
show ip ipvpn
Displays the configuration for IP VPN enabled VRFs.
Syntax
show ip ipvpn [vrf <value>] [vrfids <value>]
Default
None
Command mode
Global configuration mode
show ip ipvpn rd
Displays the configured route distinguisher for IP VPN enabled VRFs.
Syntax
show ip ipvpn rd [vrf <value>] [vrfids <value>]
Default
None
Command mode
Global configuration mode
Syntax
show ip ipvpn route-target [vrf <value>] [vrfids <value>]
Default
None
Command mode
Privileged EXEC mode
show ip irdp
Display route discovery information.
Syntax
show ip irdp [vrf WORD<0-64>][vrfids WORD<0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
vrf WORD<064> Specifies the VRF name.
vrfids WORD<0255> Specifies the VRF IDs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip irdp interface
Syntax
show ip irdp interface [gigabitethernet <1-4094> <slot/port>] [vlan <1-4094>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
gigabitethernet <14094> Specifies the Gigabit Ethernet interface by VLAN ID or
<slot/port> slot/port.
vlan <14094> Specifies the VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip isis redistribute
Default
None
Command mode
Global configuration mode
Syntax
show ip mroute hw-group-prune-state [<A.B.C.D>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<A.B.C.D> Specifies a group IP address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip mroute hw-group-
trace
Syntax
show ip mroute hw-group-trace [<A.B.C.D>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<A.B.C.D> Specifies a group IP address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip mroute hw-
resource-usage
Syntax
show ip mroute hw-resource-usage [vrf WORD<0-32>] [vrfids WORD<0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf WORD<032> Specifies a VRF instance by name.
vrfids WORD<0255> Specifies a range of VRFs by ID number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip mroute interface
Syntax
show ip mroute interface <fastethernet|gigabitethernet> [<slot/port>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<fastethernet|gigabitethernet> Shows the mroute configuration information on the
interface.
slot/port Specifies the slot and the port number on which the mroute
information is displayed.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip mroute next-hop
Syntax
show ip mroute next-hop [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip mroute route
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip mroute static-source-group [<GroupAddress>] [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip msdp count [<0-65535>]
Default
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Optionally, shows the MSDP count for a specific autonomous system, from 065535. If
as-
number you do not specify an autonomous system number, the command results show global
information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip msdp mesh-group
Syntax
show ip msdp mesh-group [Word<1-64>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Optionally, specifies the name of a specific mesh group, from 164 characters, to include
164 in the command results. If you do not specify a mesh group name, the results include all
mesh groups.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip msdp peer
Syntax
show ip msdp peer [<A.B.C.D>] [<accepted-sas|advertised-sas>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
A.B.C.D Optionally, specifies the IP address of the MSDP peer. If you do not specify an IP
address, the results of this command show all MSDP peers.
accepted- Optionally, shows either the SA messages MSDP accepts from or advertises to
sas|advertised- the peer. If you do not select one of these options, the results of this command
sas show all MSDP peer information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip msdp rpf
Syntax
show ip msdp rpf <A.B.C.D>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
A.B.C.D Specifies the RP address of the multicast group for which you request the upstream RPF
peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip msdp sa-cache
Syntax
show ip msdp sa-cache [foreign|local] [group <A.B.C.D>] [rp <A.B.C.D>] [source <A.B.C.D>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
foreign|local Shows either the local or the foreign SA cache.
group <A.B.C.D> Optionally, shows all cache entries that match the group address.
rp <A.B.C.D> Optionally, shows all cache entries that match the rendezvous point address.
source <A.B.C.D> Optionally, shows all cache entries that match the source address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip msdp sa-check
source
Syntax
show ip msdp sa-check source <A.B.C.D> group <A.B.C.D> rp <A.B.C.D> [peer <A.B.C.D>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
group
<A.B.C.D> Specifies the group address as part of the received SA message.
Optionally, checks whether the router can receive (S, G, RP) entries from this peer
address. If you do not specify the peer address, the router uses the RPF peer calculated
peer by using the RP address as the peer to validate the (S, G, RP) information. If you do
<A.B.C.D> specify the peer address, the router compares the RPF peer calculated by using the RP
address against the peer address and if a match exists, the router validates the (S, G,
RP) by using the peer inbound filter.
rp Specifies the RP address of the multicast group for which you request the upstream RPF
<A.B.C.D> peer.
source
<A.B.C.D> Specifies the source address as part of the received SA message.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip msdp show-all
Syntax
show ip msdp show-all [Word<1-99>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Optionally, specifies a file name to use to save the output of the command. Use the
199 format /pcmcia/<file> or /flash/<file> where <file> is the file name up to 99 characters
in length.
default- Configures the value of default import metric to import a route into RIP domain.
metric
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip msdp summary
Syntax
show ip msdp summary
Default
None
Command mode
Privileged EXEC mode
show ip ospf
Displays OSPF general information for the specific VRF or VRF IDs.
Syntax
show ip ospf [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf <WORD 0-16> Specifies a VRF by name.
vrfids <WORD 0-255> Specifies a range of VRF IDs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf accept
Syntax
show ip ospf accept [vrf <WORD 0-32>] [vrfids <0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[vrf <WORD<0-32>] The name of the VRF.
[vrfids <0-255>] The ID of the VRF. The value is an integer between 0 and 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf area
Syntax
show ip ospf area [vrf WORD<0-32>] [vrfids WORD<0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf WORD<032> Specifies a VRF by name.
vrf WORD<0255> Specifies a range of VRF IDs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf area-range
Syntax
show ip ospf area-range [vrf WORD<0-32>] [vrfids WORD<0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf WORD<032> Specifies a VRF by name.
vrf WORD<0255> Specifies a range of VRF IDs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf ase
Syntax
show ip ospf ase [metric-type <1-2>] [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
metric-type <1-2> Specifies the metric type as a string of 1 to 2 characters.
vrf <WORD 0-16> Identifies the VRF by name.
vrfids <WORD 0-255> Specifies a VRF by ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf authentication
interface
Syntax
show ip ospf authentication interface [gigabitEthernet <slot/port>] [vlan <1-4094>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
gigabitEthernet Specifies the Gigabit Ethernet interface by slot and port
<slot/port> numbers.
vlan <14094> Specifies the VLAN ID from 14094.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf default-cost
Syntax
show ip ospf default-cost [vrf WORD<0-32>] [vrfids WORD<0-255>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf WORD<032> Specifies a VRF by name.
vrf WORD<0255> Specifies a range of VRF IDs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf host-route
Syntax
show ip ospf host-route [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf <WORD 0-16> Specifies a VRF by name.
vrfids <WORD 0-255> Specifies a range of VRF IDs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf ifstats
Syntax
show ip ospf ifstats [vrf <Word 0-32>] [vrfids <Word 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf <Word 0-32> Specifies the VRF name in the range of 0 to 32 characters.
vrfids <Word 0-255> Specifies the VRF ID in the range of 0 to 255.
[mismatch] mismatch is the number of times the area ID is not matched.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf int-auth
Syntax
show ip ospf int-auth [vrf WORD<0-32>] [vrf WORD<0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf WORD<032> Specifies a VRF by name.
vrf WORD<0255> Specifies a range of VRF IDs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf interface
Syntax
show ip ospf interface [<interface-type>] [<interface-id>] [vrf <WORD 1-16>] [vrfids <0-
255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
interface-
id Specifies the interface ID.
interface- Specifies the type of interface if you want to limit the output. The options are
type fastethernet, gigabitethernet, pos, or vlan.
vrf <WORD
1-16> Dispays OSPF configuration for a particular virtual router and forwarder (VRF).
vrfids <0-
255> Specifies the VRF ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf int-timers
Syntax
show ip ospf int-timers [vrf WORD<0-32>] [vrfids WORD<0-255>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf WORD<032> Specifies a VRF by name.
vrf WORD<0255> Specifies a range of VRF IDs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf lsdb
Syntax
show ip ospf lsdb [area <A.B.C.D>] [lsatype <0-7>] [lsid <A.B.C.D>] [adv_rtr <A.B.C.D>]
[vrf <WORD 0-16>] [vrfids <WORD 0-255>] [detail]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
adv_rtr <A.B.C.D> Specifies the advertising router.
area <A.B.C.D> Specifies the OSPF area.
detail Provides detailed output.
lsatype <0-7> Specifies the link-state advertisement type in the range of 0 to 7.
lsid <A.B.C.D> Specifies the link-state ID.
vrf <WORD 0-16> Specifies a VRF by name.
vrfids <WORD 0-255> Specifies a range of VRF IDs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf neighbor
Syntax
show ip ospf neighbor [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf <WORD 0-16> Specifies a VRF by name.
vrfids <WORD 0-255> Specifies a range of VRF IDs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf neighbors
interface
Syntax
show ip ospf neighbors interface [vrf <value>] [vrfids <value>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip ospf port-error [port <portList>] [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
portlist Specifies the slot and the port number.
vrf <Word 0-16> Name of the VRF in the range of 0 to 16 characters.
vrfids <Word 0-255> Specifies the VRF ID in the range of 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf redistribute
Syntax
show ip ospf redistribute [vrf <WORD 0-16>] [vrfids <1-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf Specifies the VRF instance by name. When applying a redistribution instance that
<WORD 0- redistributes from a nonzero VRF to VRF 0 (the global router), do not specify the
16> destination VRF; only specify the source VRF.
vrfids
<1-255> Specifies a list of VRF IDs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf stats
Syntax
show ip ospf stats [vrf <value>] [vrfids <value>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[vrf <value>] Specifies a VRF instance by VRF name.
[vrfids <value>] Specifies a VRF or range of VRFs by ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip ospf virtual-link
Syntax
show ip ospf virtual-link [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf <WORD 0-16> Specifies a VRF.
vrfids <WORD 0-255> Specifies a range of VRF IDs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip pgm
show ip pgm
Display the PGM global status on the switch.
Syntax
show ip pgm
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip pgm interface <fastEthernet|gigabitethernet|vlan>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<fastethernet|gigabitethernet|vlan> Displays the IP PGM configuration information on any
one of the interfaces.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip pgm interface
statistics nak
Syntax
show ip pgm interface statistics nak
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip pgm interface statistics parity
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip pgm retransmit
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip pgm session
Default
None
Command mode
Privileged EXEC mode
show ip pim
Verify the configuration by displaying the global status of PIM on the switch.
Syntax
show ip pim [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
vrf Word <0-16> Specifies the VRF name in the range of 0 to 16.
vrfids Word <0-255> Specifies the VRF ID in the range of 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip pim active-rp
Syntax
show ip pim active-rp <group IP address> [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip pim bsr [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip pim interface [fastEthernet <slot/port>] [gigabitethernet <slot/port>] [pos
<slot/port>] [vlan <slot/port>] [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip pim mode [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip pim mroute [group <IP address>] [source <IP address>] [vrf Word<0-16>] [vrfids
Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip pim neighbor [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip pim rp-candidate [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf word <0-16> Specifies the name of the VRF with a string length of 0 to 16 characters.
vrfids Word <0-255> Specifies the VRF ID in the range of 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip pim rp-hash
Syntax
show ip pim rp-hash [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip pim static-rp [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip pim virtual-neighbor [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Privileged EXEC mode
show ip prefix-list
Display the prefix list.
Syntax
show ip prefix-list [<WORD 1-64>] [prefix <A.B.C.D>] [vrf <WORD 0-32>] [vrfids <0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<A.B.C.D/0- Adds a prefix entry to the prefix list. A.B.C.D/0-32 is the IP address and mask.
32> <ge|le> <0-32> Lower bound and higher bound mask lengths together can define a
[<ge|le> range of networks. Use the no operator to remove a prefix entry from the prefix list:
<0-32>] no ip prefix-list <WORD 1-64> <A.B.C.D/0-32>
name <WORD
1-64> Renames the specified prefix list. The name length is from 1 to 64 characters.
vrf <WORD
0-32> The name of the VRF.
vrfids <0-
255> The ID of the VRF and is an integer in the range of 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip redistribute
show ip redistribute
Display and ensure the accuracy of the configuration settings.
Syntax
show ip <rip|ospf|bgp> redistribute [vrf <WORD 0-16>] [vrfids <0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<ospf|bgp|static|direct|rip> Specifies the type of routes to redistribute-the protocol source.
vrf <WORD 0-16> Specifies the VRF instance.
vrfids <0-255> Specifies a list of VRF IDs.
vrf-src <WORD 0-16> Specifies the source VRF instance. This parameter is not
required for redistribution within the same VRF.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip rip
show ip rip
Display RIP configuration information to ensure the configuration is accurate.
Syntax
show ip rip [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
vrf <WORD 0-16> Specifies a VRF by name.
vrfids <WORD 0-255> Specifies a range of VRF IDs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip rip interface
Syntax
show ip rip interface [vrf <value>] [vrfids <value>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip rip redistribute [vrf <WORD 0-16>] [vrfids <1-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vrf Specifies the VRF instance by name. When applying a redistribution instance that
<WORD 0- redistributes from a nonzero VRF to VRF 0 (the global router), do not specify the
16> destination VRF; only specify the source VRF.
vrfids
<1-255> Specifies a list of VRF IDs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip route
show ip route
Displays route table information for the specified VRF or VRF IDs.
Syntax
show ip route [<A.B.C.D>] [-s <A.B.C.D> <A.B.C.D>] [alternative] [count-summary [vrf
WORD<0-64>] [vrfids WORD<0-255>] [preference [next-hop-vrf <WORD 0-16>]] [spbm-nh-as-mac]
[static [-s <A.B.C.D>] [vrf WORD<0-64>] [vrfids WORD<0-255>] [<A.B.C.D>]] [vrf <WORD 0-16>]
[vrfids <WORD 0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<A.B.C.D> Specifies the IP address of the route to the
network.
-s <A.B.C.D> <A.B.C.D> Indicates the IP address and subnet mask for
which to display routes.
alternative alternative displays the alternative routes.
count-summary [vrf WORD<0-64>] [vrfids Displays a summary of route table
WORD<0-255>] information for the specified VRF or VRF IDs.
preference [next-hop-vrf <WORD 0-16>] preference displays the route preference.
spbm-nh-as-mac Displays information about the SPBM route's
next hop.
static [-s <A.B.C.D>] [vrf WORD<0-64>] Displays static route information for the
[vrfids WORD<0-255>] [<A.B.C.D>] specified subnet, VRF, or VRF IDs.
vrf WORD<0-64> Specifies a VRF instance by VRF name.
vrfids WORD<0-255> Specifies a VRF instance by VRF number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip route a.b.c.d
Syntax
show ip route -s <default> <A.B.C.D/X>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
-s <default> Displays IP route information for a specific subnet mask.<default> specifies the
<A.B.C.D/X> default subnet mask.<A.B.C.D/X> specifies the IP address or subnet mask.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip route count-
summary
Syntax
show ip route count-summary [vrf <value>] [vrfids <value>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ip route preference [vrf <WORD 0-16>] [vrfids <WORD 0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
vrf <WORD 0-16> Specifies a VRF instance by VRF name.
vrfids <WORD 0-255> Specifies a VRF instance by VRF number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip routing
show ip routing
Displays the ip routing configuration information.
Syntax
show ip routing
Default
None
Command mode
Global configuration mode
show ip rsmlt
Show IP RSMLT information to view data about all RSMLT interfaces.
Syntax
show ip rsmlt [<local|peer>] [vrf <value>] [vrfids <value>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[<local|peer>] Specifies values for the local or peer switch.
[vrf <value>] Displays IP routing for a VRF.
[vrfids <value>] Displays IP routing for a range of VRFs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip rsmlt edge-support
Syntax
show ip rsmlt edge-support
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vlan ID The ID of the VLAN in the range of 1 to 4094.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip source binding
Syntax
show ip source binding [<A.B.C.D>] [interface <interface type>] [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<A.B.C.D> Identifies the IP address or group of addresses that IP Source Guard allowed.
<interface Identifies the ID of interface for which you want IP Source Guard-allowed
type> addresses displayed.
<portlist> Specifies the port number for a single port or range of ports, entered as
{slot/port[-slot/port][,...]}.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip static-mroute
show ip static-mroute
View the route to reach a specific RPF address in the route table.
Syntax
show ip static-mroute [ip <A.B.C.D>] [rpf <A.B.C.D>] [vrf <WORD 0-32>] [vrfids <0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
A.B.C.D Specifies the IP address of the RPF neighbor or the static route.
A.B.C.D/0-32 Specifies the IP address and the network mask for the route.
[vrf <WORD 0-32>][vrfids Specifies a VRF name or a range of VRF IDs to include in the
<0-255>] show command results.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip tcp statistics
Syntax
show ip tcp statistics
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
statistics Displays IP TCP global statistics command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip traffic-filter
show ip traffic-filter
View the filter ID and counter information for all filters that have statistics gathering enabled, or for a specific filter ID to manage
network performance.
Syntax
show ip traffic-filter statistics [<1-3071]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-3071> Specifies the filter ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ipv6 address interface
Syntax
show ipv6 address interface [ip WORD<0-46>] [tunnel <1-5000>] [vlan <1-4094>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
ip WORD<046> Specifies the interface ID.
tunnel <15000> Specifies the tunnel ID.
vlan <14094> Specifies the VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ipv6 dhcp-relay
counters
Syntax
show ipv6 dhcp-relay counters
Default
None
Command mode
Privileged EXEC mode
Syntax
show ipv6 dhcp-relay fwd-path
Default
None
Command mode
Privileged EXEC mode
Syntax
show ipv6 dhcp-relay interface <interface-type> <interface-id>
Default
None
Command mode
Privileged EXEC mode
Syntax
show ipv6 forwarding
Default
None
Command mode
Privileged EXEC mode
Syntax
show ipv6 global
Default
None
Command mode
Privileged EXEC mode
Syntax
show ipv6 interface [<interface-type>] [<interface-id>] [<interface-index>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
interface-
id Specifies the interface ID.
interface-
index Specifies the index from 1 to 4096.
interface- Specifies the type of interface if you want to limit the output. The options are
type fastEthernet, gigabitEthernet, icmpstatistics, statistics, or vlan.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ipv6 mld-cache
interface
Syntax
show ipv6 mld-cache interface <interface-type> <interface-id> [grp-address <0-46>]
[detail]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
grp-
address Specifies the group address to display.
interface-
id Specifies the interface ID.
interface- Specifies the type of interface if you want to limit the output. The options are
type fastEthernet, gigabitEthernet, or vlan.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ipv6 mld interface
Syntax
show ipv6 mld interface [<interface-type> <interface-id>] [detail]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
interface-
id Specifies the interface ID.
interface- Specifies the type of interface if you want to limit the output. The options are
type fastEthernet, gigabitEthernet, or vlan.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ipv6 nd-prefix
interface
Syntax
show ipv6 nd-prefix interface <interface-type> <interface-id>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
interface-
id Specifies the interface ID.
interface- Specifies the type of interface if you want to limit the output. The options are
type fastEthernet, gigabitEthernet, or vlan.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ipv6 neighbor
Syntax
show ipv6 neighbor [<ipv6addr>] [type {other|dynamic|static|local}] [interface <interface-
type> <interface-id>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
interface-
id Specifies the interface ID.
interface- Specifies the type of interface if you want to limit the output. The options are
type fastEthernet, gigabitEthernet, or vlan.
type Specifies the type of mapping as one of the following:other dynamic static local
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ipv6 ospf
Syntax
show ipv6 ospf
Default
None
Command mode
Privileged EXEC mode
Syntax
show ipv6 ospf area
Default
None
Command mode
Privileged EXEC mode
Syntax
show ipv6 ospf int-timers
Default
None
Command mode
Privileged EXEC mode
Syntax
show ipv6 ospf lsdb [scope <1-3>] [tunnel <1-2147483647>] [area <A.B.C.D>] [lsa-type <1-
8>] [adv-rtr <A.B.C.D>] [lsid <0-4294967295>] [detail]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ipv6 ospf neighbor
Default
None
Command mode
Privileged EXEC mode
Syntax
show ipv6 ospf interface [{vlan|fastEthernet|gigabitEthernet} {vlan-id|slot/port}]
Default
None
Command mode
Privileged EXEC mode
Syntax
show ipv6 prefix-list [prefix WORD<1-256>] [WORD<1-64>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
prefix WORD<1256> Specifies the prefix IPv6 address.
WORD<164> Specifies the prefix IPv6 name.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ipv6 route static
Syntax
show ipv6 route static
Default
None
Command mode
Privileged EXEC mode
Syntax
show ipv6 tcp [connections WORD<0-128> <slot/port>] [listener WORD<0-128>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
connections [WORD<0128>] Specifies the local or remote connection by IPv6 address or
[<slot/port>] slot and port number.
listener WORD<0128> Specifies the local listener by IPv6 address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ipv6 trace
Syntax
show ipv6 trace {base | forwarding | nd | ospf | rtm | transport}
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
base Shows the status of the IPv6 base commands.
forwarding Shows the status of the IPv6 forwarding commands.
nd Shows the status of the IPv6 nd commands.
ospf Shows the status of the IPv6 ospf commands.
rtm Shows the status of the IPv6 rtm commands.
transport Shows the status of the IPv6 transport commands.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ipv6 tunnel
Syntax
show ipv6 tunnel [<tunnel-id>] [local <A.B.C.D>] [remote <A.B.C.D>] [detail]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
detail Displays address information in addition to basic tunnel information.
tunnel-id Specifies the ID number of the tunnel in the range 1 through 2 147 483 647.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ipv6 UDP
Syntax
show ipv6 udp [endpoints local_addr WORD<0-128>] local_addr WORD<0-128>] [remote_addr
WORD<0-128>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
endpoints local_addr WORD<0128> Specifies the IPv6 address of the UDP endpoint.
local_addr WORD<0128> Specifies the UDP local IPv6 address.
remote_addr WORD<0128> Specifies the UDP remote IPv6 address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ipv6 vrrp
Syntax
show ipv6 vrrp
Default
None
Command mode
Interface configuration mode
Syntax
show ipv6 vrrp address [link-local <fe80::X:X:X:X>] [vrid <1-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[link-local <fe80::X:X:X:X>] Displays information by link-local IPv6 address.
[vrid <1255>] Displays information by virtual router ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ipv6 vrrp interface
Syntax
show ipv6 vrrp interface <port-type> [<1-4094>][<portList>] vlan [<1-4094>] [<portList>]
vrid <1-255> [statistics] [verbose]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<port-type> [<14094>] Displays information by port type and optionally by specified
[<portList>] VLAN IP and ports.
vlan [<14094>][<portList>] Displays information by VLAN and optionally by specified VLAN
ID and ports.
vrid <1255> Displays information by virtual router ID.
statistics Displays VRRP statistics for the interface.
verbose Displays extended information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ipv6 vrrp statistics
Syntax
show ipv6 vrrp statistics [link-local <fe80::X:X:X:X>] [vrid <1-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[link-local <fe80::X:X:X:X>] Displays information by link-local IPv6 address.
[vrid <1255>] Displays information by virtual router ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip verify source
Syntax
show ip verify source interface [<interface type>] [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<interface Identifies the type of interface for which you want to view IP Source Guard
type> configuration information. Values are FastEthernet and GigabitEthernet.
<portlist> Specifies a single port or range of ports, entered as {slot/port[-slot/port][,...]}.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip vrf
show ip vrf
Displays configuration and operational information for the specified VRF.
Syntax
show ip vrf <value> [vrfids <value>]
Default
None
Command mode
VRF router configuration mode
Syntax
show ip vrf max-routes [WORD<0-64> [vrfids WORD<0-255>]
Default
None
Command mode
VRF router configuration mode
Syntax
show ip vrrp address [vrid <1-255>] [addr <A.B.C.D>] [vrf <WORD 0-32>] [vrfids <0-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
addr
<A.B.C.D> The IP address of the master VRRP.
vrf
<WORD 0- The name of the VRF.
32>
vrid <1- A unique integer value that represents the virtual router ID in the range 1 to 255. The
255> virtual router acts as the default router for one or more assigned addresses.
vrfids
<0-255> The ID of the VRF and is an integer in the range of 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip vrrp interface vlan
Syntax
show ip vrrp interface vlan [<1-4094>] [portList] verbose [vrf <WORD 1-16>] [vrfids <0-
255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> The VLAN ID in the range of 1 to 4094.
portList The slot/port number of a range of ports.
vrf <WORD 1-16> The name of the VRF.
vrfids <0-255> The ID of the VRF and is an integer in the range of 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ip vrrp statistics
Syntax
show ip vrrp statistics [address <A.B.C.D>] [vrf WORD<0-64>] [vrfids WORD<0-255>] [vrid
<1-255>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
address
<A.B.C.D> Specifies the IP address of the backup VRRP.
vrf
WORD<0- Specifies the VRF name.
64>
vrfids
WORD<0- Specifies the VRF ID in the range of 0 to 255.
255>
vrid <1- Specifies a unique integer value that represents the virtual router ID in the range 1 to
255> 255. The virtual router acts as the default router for one or more assigned addresses.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show isis
show isis
Display the global IS-IS configuration.
Syntax
show isis
Default
None
Command mode
User EXEC mode
Syntax
show isis adjacencies
Default
None
Command mode
User EXEC mode
Syntax
show isis area
Default
None
Command mode
Privileged EXEC mode
Syntax
show isis int-auth
Default
None
Command mode
User EXEC mode
Syntax
show isis int-ckt-level
Default
None
Command mode
User EXEC mode
Syntax
show isis int-counters
Default
None
Command mode
User EXEC mode
Syntax
show isis interface [l1|l2|l12]
Default
None
Command mode
User EXEC mode
Command parameters
Parameter Description
[l1, l2, l12] Displays the interface information for the specified level: l1, l2, l2.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show isis int-l1-cntl-pkts
Syntax
show isis int-l1-cntl-pkts
Default
None
Command mode
User EXEC mode
Syntax
show isis int-l2-cntl-pkts
Default
None
Command mode
User EXEC mode
Syntax
show isis int-timers
Default
None
Command mode
User EXEC mode
Syntax
show isis lsdb [level <value>] [sysid <sys-id>] [lspid <lsp-id>] [tlv <value>] [detail]
Default
None
Command mode
User EXEC mode
Command parameters
Parameter Description
[level <value>] Displays the LSDB for the specified level: l1, l2, or l12.
[sysid <sys-id>] Displays the LSDB for the specified system ID.
[lspid <value>] Displays the LSDB for the specified LSP ID.
[tlv <value>] Displays the LSDB by TLV type: 1184.
[detail] Displays detailed information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show isis manual-area
Syntax
show isis manual-area
Default
None
Command mode
User EXEC mode
Syntax
show isis net
Default
None
Command mode
User EXEC mode
Syntax
show isis spbm
Default
None
Command mode
Global configuration mode
Syntax
show isis spbm drop-stats port last drop
Default
None
Command mode
Privileged EXEC mode
Syntax
show isis spbm drop-stats port rpfc-multicast-sa
Default
None
Command mode
Privileged EXEC mode
Syntax
show isis spbm drop-stats port rpft-unicast-sa
Default
None
Command mode
Privileged EXEC mode
Syntax
show isis spbm drop-stats port unknown-multicast-da
Default
None
Command mode
Privileged EXEC mode
Syntax
show isis spbm drop-stats port unknown-unicast-da
Default
None
Command mode
Privileged EXEC mode
Syntax
show isis spbm ip-multicast route [all | detail | vlan | vrf | vsn-isid]
Default
None
Command mode
User EXEC mode
Command parameters
Parameter Description
all Shows all the entries across all the VSNs
detail Shows the entries in the GRT L3VSN.
vlan Shows all the entries for the particular L2VSN. Use this option if the type is snoop.
vrf Shows all the entries for the particular L3VSN. Use this option if the type is routed.
vsn-isid Shows all the entries for the particular VSN (either L2 or L3).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show isis spbm ip-unicast-
fib
Syntax
show isis spbm ip-unicast-fib [all][id <116777215>][spbm-nh-as-mac]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[all] Displays all i-sid.
[id <value>] Displays information for the specified i-sid: type a value in the range from 1 to
16777215.
[spbm-nh-as-
mac] Displays the entry's next hop as Mac.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show isis spbm i-sid
Syntax
show isis spbm i-sid {all|config|discover} [vlan <vid>] [id<isid>] [nick-name <nickname>]
Default
None
Command mode
User EXEC mode
Command parameters
Parameter Description
{all|config|discover} all: displays all I-SID entries config: displays configured I-SID entries
discover: displays discovered I-SID entries
[vlan <vid>] Displays I-SID information for the specified SPBM VLAN.
[id <isid>] Displays I-SID information for the specified I-SID.
[HostName] Specifies the target host name.
[nick-name
<nickname>] Displays I-SID information for the specified nickname.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show isis spbm multicast-fib
Syntax
show isis spbm multicast-fib [vlan <value>] [i-sid <value>] [nick-name <value>] [summary]
Default
None
Command mode
User EXEC mode
Command parameters
Parameter Description
[vlan <value>] Displays the FIB for the specified SPBM VLAN.
[i-sid <value>] Displays the FIB for the specified ISID.
[nick-name <value>] Displays the FIB for the specified nickname.
summary Displays a summary of the FIB.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show isis spbm nick-name
Syntax
show isis spbm nick-name
Default
None
Command mode
Privileged EXEC mode
Syntax
show isis spbm show-all
Default
None
Command mode
Privileged EXEC mode
Syntax
show isis spbm unicast-fib [b-mac <value>] [vlan <value>] [summary]
Default
None
Command mode
User EXEC mode
Command parameters
Parameter Description
[b-mac <value>] Displays the FIB for the specified BMAC.
[vlan <value>] Displays the FIB for the specified SPBM VLAN.
summary Displays a summary of the FIB.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show isis spbm unicast-tree
Syntax
show isis spbm unicast-tree <vlan> [destination <value>]
Default
None
Command mode
User EXEC mode
Command parameters
Parameter Description
<vlan> Specifies the VLAN ID.
[destination<value>] Displays the unicast tree for the specified destination.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show isis statistics
Syntax
show isis statistics
Default
None
Command mode
User EXEC mode
Syntax
show isis system-id
Default
None
Command mode
User EXEC mode
show ist
Display interswitch trunk (IST) information.
Syntax
show ist [mlt] [stat]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
mlt Displays MLT IST configuration information.
stat Displays IST statistics.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show khi chassis
Syntax
show khi chassis [all] [history]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
[all] Displays all chassis KHI information, including the event history.
[history] Displays the event history (max 10).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show khi forwarding
Syntax
show khi forwarding [<all|asic|current-status|f2x|history|rsp-state|rsp-stats>][slot
<value>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
all Displays all forwarding KHI information.
asic Displays ASIC health information.
current-status Displays the current status of forwarding by slot.
f2x Displays F2X health information
history Displays the event history (max 10).
rsp-state Displays ingress and egress RSP state information.
rsp-stats Displays ingress and egress RSP statistics.
[slot <value>] Displays information for a specific slot.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show khi info
Syntax
show khi info
Default
None
Command mode
Global configuration mode
Syntax
show khi ip-interface
Default
None
Command mode
Global configuration mode
Syntax
show khi mgmt [all] [history]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
[all] Displays all management KHI information, including the event history
[history] Displays the event history (max 10).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show khi performance
Syntax
show khi performance [all] [history]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
[all] Displays all performance KHI information, including the event history..
[history] Displays the event history (max 10).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show khi port
Syntax
show khi port [<all|errors|history|state|system-stats>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
all Displays all KHI information
errors Displays port errors.
history Displays the event history (max 10).
state Displays port state (up, down, and health), including the port state for SMLT and IST
ports.
system-
stats Displays system port statistics for unicast, multicast, and broadcast packets.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show khi protocol-stats
Syntax
show khi protocol-stats [history] [vrf <vrfName>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
history Displays the event history (max 10.
vrf <vrfName> Displays VRF-specific data.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show lacp
show lacp
View LACP configuration information to determine the LACP parameters and to ensure your configuration is correct.
Syntax
show lacp
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Shows LACP actor administrative information for all
actor-admin interface interfaces or the specified interface. vlan-id is the
[{fastethernet|gigabitethernet}]
[vid {vlan-id[-vlan-id][,...]}] VLAN ID or list of VLAN IDs to show only ports
[<portList>] attached to a particular VLAN. The range is 14094.
portList is the port or port list.
Shows LACP actor operational information for all
actor-oper interface interfaces or the specified interface. vlan-id is the
[{fastethernet|gigabitethernet}]
[vid {vlan-id[-vlan-id][,...]}] VLAN ID or list of VLAN IDs to show only ports
[<portList>] attached to a particular VLAN. The range is 14094.
portList is the port or port list.
Shows LACP timer information for all interfaces or
extension interface the specified interface. vlan-id is the VLAN ID or list
[{fastethernet|gigabitethernet}]
[vid {vlan-id[-vlan-id][,...]}] of VLAN IDs to show only ports attached to a
[<portList>] particular VLAN. The range is 14094. portList is the
port or port list.
interface
[{fastethernet|gigabitethernet|pos}] Shows all LACP port configuration information for all
[vid {vlan-id[-vlan-id][,...]}] interfaces or the specified interface.
[<portList>]
interface mlt [<646399>] Shows the MLT LACP information for all MLTs or the
specific MLT index.
Shows LACP partner administrative information for
partner-admin interface all interfaces or the specified interface. vlan-id is the
[{fastethernet|gigabitethernet}]
[vid {vlan-id[-vlan-id][,...]}] VLAN ID or list of VLAN IDs to show only ports
[<portList>] attached to a particular VLAN. The range is 14094.
portList is the port or port list.
Shows LACP partner operational information for all
partner-oper interface interfaces or the specified interface. vlan-id is the
[{fastethernet|gigabitethernet}]
[vid {vlan-id[-vlan-id][,...]}] VLAN ID or list of VLAN IDs to show only ports
attached to a particular VLAN. The range is 14094.
[<portList>]
portList is the port or port list.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show lacp interface
Syntax
show lacp interface <fastethernet|gigabitethernet> {slot/port [-slot/port]}
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
vid Shows ports attached to a particular VLAN.
{slot/port [-slot/port]} Specify the ports.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show license
show license
Display the existing software licenses on your switch.
Syntax
show license
Default
None
Command mode
Privileged EXEC mode
show link-flap-detect
Display the link flap detect information.
Syntax
show link-flap-detect
Default
None
Command mode
Privileged EXEC mode
Syntax
Default
Command mode
Privileged EXEC mode
Syntax
show logging config
Default
Command mode
Privileged EXEC mode
Syntax
show logging file [tail] [category <WORD 0-100>] [severity <WORD 0-25>] [CPU <WORD 0-25>]
[name-of-file <WORD 1-99>] [save-to-file <WORD 1-99>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Filters and list the logs according to category. Specify a string length of 0100 characters.
category Categories include SNMP, EAP, RADIUS, RMON, WEB, STG, IGMP, HW, MLT, FILTER,
<WORD 0- QOS, SW, CPU, IP, VLAN, IPMC, ATM, DVMRP, IP-RIP, MPLS, OSPF, |PIM, POLICY, POS,
100> RIP. To specify multiple filters, separate each category by the vertical bar (|), for
example, OSPF|FILTER|QOS.
CPU Filters and list the logs according to the SF/CPU that generated it. Specify a string length
<WORD 0- of 025 characters. To specify multiple filters, separate each SF/CPU by the vertical bar
25> (|), for example, CPU5|CPU6.
name-of- Displays the valid logs from this file. For example, /pcmcia/logcopy.txt. You cannot use
file
<WORD 1- this command on the current log file-the file into which the messages are currently
99> logged). Specify a string length of 199 characters.
save-to- Redirects the output to the specified file and remove all encrypted information. The tail
file
<WORD 1- option is not supported with the save-to-file option. Specify a string length of 199
99> characters.
severity Filters and list the logs according to severity. Choices include INFO, ERROR, WARNING,
<WORD 0- FATAL. To specify multiple filters, separate each severity by the vertical bar (|), for
25> example, ERROR|WARNING|FATAL.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show logging level
Syntax
show logging level
Default
Command mode
Privileged EXEC mode
Syntax
show logging transferFile <1-10>
Default
Command mode
Privileged EXEC mode
show mirror-by-port
Display port mirroring information to aid in diagnostic and security operations.
Syntax
show mirror-by-port
Default
None
Command mode
Privileged EXEC mode
Syntax
show mlt error collision [<mltid>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<mltid> Specifies the MLT ID. The value ranges from 1256.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mlt error main
Syntax
show mlt error main [<mltid>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<mltid> Specifies the MLT ID. The value ranges from 1256.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mlt stats
Syntax
show mlt stats <mltid>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<mltid> Specifies the MLT ID. The value ranges from 1256.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show monitor-statistics
show monitor-statistics
Display the monitor timer statistics.
Syntax
show monitor-statistics
Default
None
Command mode
Privileged EXEC mode
Syntax
show mpls basic
Default
None
Command mode
Privileged EXEC mode
Syntax
show mpls ftn
Default
None
Command mode
Privileged EXEC mode
Syntax
show mpls ilm
Default
None
Command mode
Privileged EXEC mode
Syntax
show mpls ldp
Default
None
Command mode
Privileged EXEC mode
Syntax
show mpls ldp bindings [min-label] [max-label] [<A.B.C.D/X>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
min-label Specify the minimum local label value bound to this FEC.
max-label Specify the maximum local label value bound to this FEC.
<A.B.C.D/X> Specify the address of another FEC.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls ldp discovery
Syntax
show mpls ldp discovery <inferface-type> [<interface-id>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
interface- Specify which interface to display. The options are FastEthernet, GigabitEthernet,
type and vlan.
interface-id Specify the interface ID for the nominate interface.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls ldp interface
Syntax
show mpls ldp interface [vlan <vlan id>] [port <portList>] [detail]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
detail Displays all available information about LDP interfaces.
port <portList> Displays LDP port configurations.
vlan Displays LDP VLAN configurations.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls ldp neighbor
Syntax
show mpls ldp neighbor [<A.B.C.D>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<A.B.C.D> Displays the IP address of a specific LDP peer
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls ldp route
Syntax
show mpls ldp route <A.B.C.D/X>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<A.B.C.D/X> Displays the route to a specific destination IP address and mask.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls ldp session
Syntax
show mpls ldp session [<A.B.C.D>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<A.B.C.D> Displays the IP address of a specific LDP peer.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls ldp summary
Syntax
show mpls ldp summary
Default
None
Command mode
Privileged EXEC mode
Syntax
show mpls mtu <FastEthernet|GigabitEthernet|vlan>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
FastEthernet Displays MTU FastEthernet configurations.
GigabitEthernet Displays MTU GigabitEthernet configurations.
vlan Displays MTU VLAN configurations.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls rsvp
Syntax
show mpls rsvp
Default
None
Command mode
Privileged EXEC mode
Syntax
show mpls rsvp explicit-path [WORD<0-32>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
WORD<0-32> Specifies the name of an explicit path.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls rsvp interface
Syntax
show mpls rsvp interface [FastEthernet] [GigabitEthernet] [vlan]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
FastEthernet Displays RSVP FastEthernet configurations.
GigabitEthernet Displays RSVP GigabitEthernet configurations.
vlan Displays RSVP VLAN discovery configurations.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls rsvp neighbor
Syntax
show mpls rsvp neighbor [detail]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
detail Displays all available information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls rsvp paths
Syntax
show mpls rsvp paths [name <lsp-name>] [type <ingress|transition|egress>] [detail]
[disabled}
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
detail Displays all available information about LDP interfaces.
disabled Displays information about LSPs that are not operational.
type Displays information about three types of LSPs: egress, ingress,
<ingress|transition|egress> and transit.
name <lsp-name> Displays the RSVP FEC information for the specified LSP.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls rsvp resource
Syntax
show mpls rsvp resource
Default
None
Command mode
Privileged EXEC mode
Syntax
show mpls rsvp static-ip lsp [WORD<0-32>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
lsp <WORD<0-32> Displays the RSVP FEC information for the specified LSP.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls statistics ldp
Syntax
show mpls statistics ldp [A.B.C.D] [detail]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Peer IPAddress The IP address of the device for which you want to view statistics.
detail Displays all captured statistics.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls statistics receive
Syntax
show mpls statistics receive [label <value>] [port <value>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[GigabitEthernet
<value>] Identifies the GigabitEthernet interface for which you are viewing statistics.
[FastEthernet
<value>] Identifies the FastEthernet interface for which you are viewing statistics.
label <value> The number representing the label at which you want the switch to start
collecting statistics. Valid values are 0 through 1048575.
[port <value>] The portlist for MPLS statistics. <slot/port>.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls statistics rsvp
Syntax
show mpls statistics rsvp[FastEthernet <value>] [GigabitEthernet <value>] [label <value>]
[vlan <value>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
FastEthernet Displays RSVP port statistics.
GigabitEthernet Displays RSVP port statistics.
vlan Displays VLAN RSVP information.
[FastEthernet <value>] Identifies the FastEthernet interface for which you are
viewing statistics.
[GigabitEthernet <value>] Identifies the GigabitEthernet interface for which you are
[label <value>] viewing statistics.
[vlan <value>] Identifies the VLAN for which you are viewing statistics.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show mpls statistics
transmit
Syntax
show mpls statistics transmit [FastEthernet <value>] [GigabitEthernet <value>] [label
<value>] [port <value>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[GigabitEthernet
<value>] Identifies the GigabitEthernet interface for which you are viewing statistics.
[FastEthernet
<value>] Identifies the FastEthernet interface for which you are viewing statistics.
label <value> The number representing the label at which you want the switch to start
collecting statistics. Valid values are 0 to 1048575.
[port <value>] The portlist for MPLS statistics. <slot/port>.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show multicast mlt-
distribution
Syntax
show multicast mlt-distribution
Default
None
Command mode
Privileged EXEC mode
Syntax
show multicast software-forwarding [vrf Word<0-16>] [vrfids Word<0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
[vrf <WORD 016>][vrfids Specifies a VRF name or a range of VRF IDs to include in the
<0255>] show command results.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show multicast square-smlt
Syntax
show multicast square-smlt
Default
None
Command mode
Privileged EXEC mode
Syntax
show nsna client [interface {GigabitEthernet <slot/port> | <slot/port>}
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
interface GigabitEthernet Specifies the Gigabit Ethernet interface to display the
<slot/port>} NSNA information.
<slot/port> Specifies the slot and the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show nsna interface
Syntax
show nsna interface {GigabitEthernet <slot/port> | <slot/port>}
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
GigabitEthernet Specifies the Gigabit Ethernet interface to display the NSNA
<slot/port> information.
<slot/port> Specifies the slot and the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show nsna nsnas
Syntax
show nsna nsnas [A.B.C.D/X]
Default
None
Command mode
Global configuration mode
Syntax
show nsna phone-signature [WORD<1-64>]
Default
None
Command mode
Global configuration mode
Syntax
show nsna vlan [<1-4094>]
Default
None
Command mode
Global configuration mode
Syntax
show ntp server
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
server Displays NTP server information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show pcap
show pcap
Display PCAP information.
Syntax
show pcap
Default
None
Command mode
Privileged EXEC mode
Syntax
show pcap capture-filter <1-1000>
Default
None
Command mode
Privileged EXEC mode
Syntax
show pcap dump
Default
None
Command mode
Privileged EXEC mode
Syntax
show pcap port
Default
None
Command mode
Privileged EXEC mode
Syntax
show pcap stats
Default
None
Command mode
Privileged EXEC mode
show ping-snoop
Display Ping Snoop configurations to troubleshoot multilink trunking configurations.
Syntax
show ping-snoop
Default
None
Command mode
Privileged EXEC mode
show pluggable-optical-module
View DDI module information to view basic SFP and XFP manufacturing information and characteristics.
Syntax
show pluggable-optical-modules basic [<ports>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
basic Displays basic SFP/XFP information.
ports A port or a range of ports in the format of slot/port. If no port list is entered the
complete detailed output displays for each port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ports statistics ospf
extended
Syntax
show ports statistics ospf extended <portList>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<portList> is the either port or slot number or a range of ports.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show ports statistics ospf
main
Syntax
show ports statistics ospf main <ports>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<ports> Specifies the port or range of ports configured in the format slot/port.
<portList> is the either port or slot number or a range of ports.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show port statistics wis
felinecurrent
Syntax
show port statistics wis felinecurrent <1-4094> [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN on which you want to view statistics.
<portList> Indicates the ports on which you want to view statistics.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show port statistics wis
felineinterval
Syntax
show port statistics wis felineinterval<1-96>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-96> Identifies the interval.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show port statistics wis
fepathcurrent
Syntax
show port statistics wis fepathcurrent <1-4094> [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN on which you want to view statistics.
<portList> Indicates the ports on which you want to view statistics.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show port statistics wis
fepathinterval
Syntax
show port statistics wis fepathinterval<1-96>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-96> Identifies the interval.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show port statistics wis
linecurrent
Syntax
show port statistics wis linecurrent <1-4094> [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[1-4094] Specifies the VLAN on which you want to view statistics.
[portList] Specifies the port on which you want to view statistics.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show port statistics wis
lineinterval
Syntax
show port statistics wis lineinterval <1-96>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-96> Identifies the interval.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show port statistics wis
pathcurrent
Syntax
show port statistics wis pathcurrent <1-4094> [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN on which you want to view statistics.
<portList> Indicates the ports on which you want to view statistics.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show port statistics wis
pathinterval
Syntax
show port statistics wis pathinterval <1-96>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-96> Identifies the interval.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show port statistics wis
sectioncurrent
Syntax
show port statistics wis sectioncurrent [1-4094][portList]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[1-4094] Specifies the VLAN on which you want to view statistics.
[portList] Specifies the port on which you want to view statistics.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show port statistics wis
sectioninterval
Syntax
show port statistics wis sectioninterval<1-96>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-96> Identifies the interval.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show port statistics wis
sonetmedium
Syntax
show port statistics wis sonetmedium <1-4094> [<portlist>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Indicates the VLAN on which you want to view statistics.
<portList> Indicates the ports on which you want to view statistics.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show qos 802.1p-override
Syntax
show qos 802.1p-override [gigabitEthernet <slot/port>] [vlan <1-4094>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
gigabitEthernet Specifies the Gigabit Ethernet interface to display the 802.1p override
<slot/port>} status information.
vlan <14094> Specifies the VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show qos egressmap
Syntax
show qos egressmap
Default
None
Command mode
Privileged EXEC mode
Syntax
show qos egress-queue-set <1-386> [port <slot/port>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1386> Specifies the egress-queue-set ID.
port <slot/port>} Specifies the egress-queue-set slot and port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show qos eqmap
Syntax
show qos eqmap
Default
None
Command mode
Privileged EXEC mode
Syntax
show qos ingressmap
Default
None
Command mode
Privileged EXEC mode
Syntax
show qos policer [interface gigabitEthernet <slot/port>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
interface Specifies the slot and port number of the Gigabit Ethernet interface
gigabitEthernet
<slot/port>} to display the rate limiting information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show qos policy-config
Syntax
show qos policy-config [<0-16383>] [lane <WORD 1-128>] [port <portList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-16383> Specifies the policer ID number.
lane <WORD 1-128> Specifies the lanes to which the policer applies:all slot/lane [-slot/lane][,-]
port <portList> Specifies the slot and port, or slot and port list.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show qos shaper
Syntax
show qos shaper [interface gigabitEthernet <slot/port>] [interface vlan <1-4094>}
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
interface gigabitEthernet Specifies the Gigabit Ethernet interface to display the port
<slot/port>} egress rate limiting information.
interface vlan <14094>} Specifies the VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show qos statistics
Syntax
show qos statistics egress-queue-set<1-386> [interface type
<fastethernet|gigabitethernet>][detail]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<interface type> fastethernet|gigabitethernet
<1-386> Specifies the transmitted queue template identifier.
[detail] Displays all details.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show qos statistics egress-
queue-set
Syntax
show qos statistics egress-queue-set <1-386> [detail]
Default
None
Command mode
Privileged EXEC mode
Syntax
show qos statistics policy
Default
None
Command mode
Privileged EXEC mode
show radius
Display the global status of RADIUS information.
Syntax
show radius
Default
None
Command mode
Privileged EXEC mode
show radius-server
Display current RADIUS server configurations.
Syntax
show radius-server
Default
None
Command mode
Privileged EXEC mode
Syntax
show radius-server statistics
Default
None
Command mode
Privileged EXEC mode
Syntax
show radius snmp
Default
None
Command mode
Privileged EXEC mode
show remote-mirroring
Display the remote mirroring configuration information.
Syntax
show remote-mirroring interfaces <fastEthernet|gigabitEthernet> [enable] [mode
<source|termination>] [srcMac <0x00:0x00:0x00:0x00:0x00:0x00>] [dstMac
<0x00:0x00:0x00:0x00:0x00:0x00>] [ether-type <0x00-0xffff>] [vlan-id <1-4094>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Sets the destination MAC address for use in the remote
mirroring encapsulation header. The mirrored packet is sent
dstMac to this MAC address. The DstMac is used only for RMS
<0x00:0x00:0x00:0x00:0x00:0x00> ports. For RMT ports, one of the unused MAC addresses
from the switch port MAC address range is used. This MAC
address is saved in the configuration file.
Enables remote mirroring on the port. When remote
mirroring is enabled, the following events occur: A static
entry for the DstMac is added to the Forwarding Database
enable (FDB). All packets that come with this remote mirroring
DstMac are sent to the RMT port. The switch periodically
(once in 10 seconds) transmits broadcast Layer 2 packets
in the associated VLAN so that all nodes in the network can
learn the DstMac.
ether-type <0x00-0xffff> Specifies the Ethertype of the remote mirrored packet. The
default value is 0x8103.
mode <source|termination> Specifies whether the port is an RMT (mode is termination)
or an RMS (mode is source).
Sets the source MAC address for use in the remote
mirroring encapsulation header. The mirrored packet is sent
from the RMS port, and the source MAC parameter in the
srcMac header is derived from this address. The source MAC
<0x00:0x00:0x00:0x00:0x00:0x00> address of the encapsulated frame contains the first 45 bits
of this MAC address. The three least significant bits are
derived from the port number of the RMS port. The MAC
address of the port is used as the default value.
Specifies to which VLAN the remote mirroring destination
MAC address belongs. This must be a port-based VLAN.
vlan-id <1-4094> Used only for Remote Mirroring Termination (RMT) ports.
When the RMT port is removed from the last VLAN in the
list, RMT is disabled on the port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show rmon
show rmon
View RMON settings to see information about alarms, statistics, events, or the status of RMON on the switch.
Syntax
show rmon
Default
None
Command mode
Privileged EXEC mode
Syntax
show rmon alarm
Default
None
Command mode
Privileged EXEC mode
Syntax
show rmon event
Default
None
Command mode
Privileged EXEC mode
Syntax
show rmon history
Default
None
Command mode
Privileged EXEC mode
Syntax
show rmon log
Default
None
Command mode
Privileged EXEC mode
Syntax
show rmon stats
Default
None
Command mode
Privileged EXEC mode
show route-map
Display current information about the IP route policy.
Syntax
show route-map [<WORD 1-64>] [<1-65535>] [vrf <WORD 0-32>] [vrfids <0-255>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<WORD 1-64> Creates a route policy with a policy name and a sequence number. WORD 1-64 is
<1-65535> the policy name. 1-65535 is the sequence number.
vrf <WORD 0-
32> The name of the VRF.
vrfids <0-
255> The ID of the VRF and is an integer in the range of 0 to 255.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show routing statistics
Syntax
show routing statistics interface[<interface-type>] [<interface-id>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[<interface-type>] Indicates the interface type.
[<interface-id>] Indicates the interface identifier.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show routing statistics
interface
Syntax
show routing statistics interface <interface> [slot/port]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
interface Specifies the interface type for which to report statistics. The options include fastethernet
and gigabitethernet.
slot/port Specifies a particular slot and port or list of ports for which to provide results. If you
omit a specific port or port list, results include all ports on the interface type.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show rsp-trace
show rsp-trace
Use this command to confirm the configuration that enables RSP ingress Packet Tracing or RSP egress Packet Tracing.
Syntax
show rsp-trace
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
ingress-pkt-trace:/egress-
pkt-trace: Specifies the Packet Tracing as ingress or egress.
port Specifies all the ports in the lane on which the trace is
enabled.
state Specifies whether Packet Tracing is enabled.
interval Specifies the interval in seconds for which the Packet
Tracing is enabled.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show running-config
show running-config
Use this command to display the current switch configuration.
Syntax
show running-config [mode (cli|acli)][module <value>][verbose]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
mode (cli|acli) Selects the mode between CLI and ACLI.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show running-config mode
acli
Syntax
show running-config mode acli
Default
Command mode
Global configuration mode
show slot
Display the administrative status of the specified module.
Syntax
show slot <1-10>
Default
None
Command mode
Privileged EXEC mode
show slpp
Use SLPP information to view loop information.
Syntax
show slpp
Default
None
Command mode
Privileged EXEC mode
Syntax
show slpp interface <FastEthernet|GigabitEthernet> <slot/port>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<FastEthernet|GigabitEthernet> Specifies the mode to display the SLPP information.
<slot/port> Specifies the slot and the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show smlt
show smlt
View all ports for a single port SMLT to ensure the correct ports are configured.
Syntax
show smlt {fastethernet|gigabitethernet|mlt|pos}
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
{fastethernet|gigabitethernet|pos} Displays SMLT information for the interface and ports
[<portList>] that you specify. portList is the port or port list.
mlt Displays SMLT information for the MLT interface.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show snmplog
show snmplog
View the contents of the SNMP log.
Syntax
show snmplog
Default
None
Command mode
Privileged EXEC mode
Syntax
show snmp-server host
Default
None
Command mode
Privileged EXEC mode
show snmp-server
Display SNMP system information to view trap and authentication profiles.
Syntax
show snmp-server [community] [context] [group] [host] [notify-filter] [user] [view]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
community Display SNMP Community table.
context Display VACM Context table.
group Display VACM Group Membership and Access Configuration tables.
host Display SNMP host information.
notify-filter Display Notify Filter Configuration table.
user Display USM Configuration table.
view Display SNMP MIB View table.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show snmp-server notify-
filter
Syntax
show snmp-server notify-filter
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces pos activealarms
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces pos felinecurrent
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces pos felineinterval <1-96>
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces pos fepathcurrent
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces pos fepathinterval <1-96>
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces pos linecurrent
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces pos lineinterval <1-96>
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces pos linkstatus
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces pos lqrstatus
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces pos pathcurrent
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces pos pathinterval <1-96>
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces pos pppiftbl
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces pos sectioncurrent
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces possectioninterval<1-96>
Default
None
Command mode
Privileged EXEC mode
Syntax
show sonet statistic interfaces pos sonetmediumtbl
Default
None
Command mode
Privileged EXEC mode
Syntax
show spanning-tree bpdu-filtering [GigabitEthernet <slot/port>] [vlan <1-4094>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
GigabitEthernet Specifies the Gigabit Ethernet interface to display the BPDU status
<slot/port>} information.
vlan <14094> Specifies the VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show spanning-tree config
Syntax
show spanning-tree config
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
config Displays the STP configuration.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show spanning-tree mstp
config
Syntax
show spanning-tree mstp config
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
config Shows the MSTP configuration information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show spanning-tree mstp
port role
Syntax
show spanning-tree mstp port role <portList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
port role Displays the MSTP port information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show spanning-tree mstp
statistics
Syntax
show spanning-tree mstp statistics
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
statistics Displays the MSTP statistics information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show spanning-tree mstp
status
Syntax
show spanning-tree mstp status
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
status Displays the MSTP port status information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show spanning-tree port
detail
Syntax
show spanning-tree port [portList] detail
Default
None
Command mode
Privileged EXEC mode
Syntax
show spanning-tree rstp config
Default
None
Command mode
Privileged EXEC mode
Syntax
show spanning-tree rstp port config [<portList>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
config <portList> Shows RSTP port configuration.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show spanning-tree rstp
port role
Syntax
show spanning-tree rstp port role [<portList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
role <portList> Shows RSTP port role.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show spanning-tree rstp
port statistics
Syntax
show spanning-tree rstp port statistics <portlist>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<portlist> The ports for which you want to view statistics.
statistics [<portList>] Shows RSTP port statistics.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show spanning-tree rstp
port status
Syntax
show spanning-tree rstp port status [<portList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
status [<portList>] Shows RSTP port status.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show spanning-tree rstp
statistics
Syntax
show spanning-tree rstp statistics
Default
None
Command mode
Privileged EXEC mode
Syntax
show spanning-tree rstp status
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
status Displays the status of the RSTP>.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show spanning-tree status
Syntax
show spanning-tree status
Default
None
Command mode
Privileged EXEC mode
Syntax
show spanning-tree [stp <1-64>] config
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
config Shows STP configuration for a particular STP Id.
<1-64> Specifies the spanning tree id in the range of 1 to 64.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show spanning-tree stp
status
Syntax
show spanning-tree [stp <1-64>] status
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
status Shows STP status for a particular STP id.
<1-64> Specifies the spanning tree id in the range of 1 to 64.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show spanning-tree vlans
Syntax
show spanning-tree vlans <1-4094>
Default
None
Command mode
Privileged EXEC mode
show spbm
Display the status (enabled or disabled) and the ethertype for SPBM (Shortest Path Bridging-Mac).
Syntax
show spbm
Default
None
Command mode
Privileged EXEC mode
show ssh
Verify that SSH services are enabled on the Avaya Ethernet Routing Switch 8800/8600 and display SSH configuration information
to ensure that the SSH parameters are properly configured.
Syntax
show ssh
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
global Displays global system SSH information.
session Displays the current session SSH information.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show sys
show sys
Use this command to display system status and technical information about the switch hardware components and software
configuration.
Syntax
show sys
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
8648gtr Displays technical information about the 8648gtr settings.
action Displays the configuration for the system action parameter.
dns Displays the DNS default domain name.
ecn- Displays the status of Explicit Congestion Notification (ECN) compatibility, either
compatibility enabled or disabled.
ext-cp-limit Displays the ext-cp-limit settings.
flags Displays the configuration of system flags.
force-msg Displays the message control force message pattern settings.
global-
filter Displays the status of system global filter settings, either enabled or disabled.
mcast-smlt Displays the settings for multicast over Split MultiLink Trunking (MLT).
mgid-usage Displays the multicast group ID (MGID) usage for VLANs and multicast traffic.
msg-control Displays the system message control function status (activated or disabled).
mtu Displays system maximum transmission unit (MTU) information.
Displays system performance information, such as CPU utilization, switch fabric
performance utilization, NonVolatile Random Access Memory (NVRAM) size, and NVRAM used.
The information is updated once a second.
Displays power information for the chassis. Command options are:group-power
power management settings power-supply-power information for each power supply slot-
power information for each slot
record- Displays the number of reserved records and usage information for each record
reservation type. Record types include filter, IP multicasting (IPMC), MAC, and static route.
setting Display system settings.
Displays the version of software running on the switch, the last update of that
software software, and the Boot Config Table. The Boot Config Table lists the current system
settings and flags.
stats Displays system statistics. For more information about statistics, see Avaya Ethernet
Routing Switch 8800/8600 Performance Management (NN46205-704).
topology-ip Displays clip-ip set as topology ip.
vlan- Displays the status of VLANs created by source MAC address, either enabled or
bysrcmac disabled.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show sys 8648gtr
Syntax
show sys 8648gtr
Default
None
Command mode
Global configuration mode
Syntax
show sys flags
Default
Command mode
Privileged EXEC mode
show sys-info
Use this command to display system status and technical information about the switch hardware components.
Syntax
show sys-info [asic] [card] [gbic] [mda]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
asic Displays information about the application-specific integrated circuit (ASIC) installed on
each module.
card Displays information about all the installed modules.
gbic Displays information about all the Gigabit Interface Converters (GBIC).
mda Displays information about installed media dependent adapters (MDA).
asic Displays ASIC information in details.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show syslog
show syslog
View the syslog information to ensure accuracy.
Syntax
show syslog
Default
None
Command mode
Privileged EXEC mode
Syntax
show syslog host <1-10>
Default
None
Command mode
Privileged EXEC mode
Syntax
show sys perf
Default
None
Command mode
Privileged EXEC mode
Syntax
show sys performance
Default
None
Command mode
Privileged EXEC mode
Syntax
show sys power
Default
None
Command mode
Privileged EXEC mode
Syntax
show sys power global
Default
None
Command mode
Privileged EXEC mode
Syntax
show sys power power-supply
Default
None
Command mode
Privileged EXEC mode
Syntax
show sys power slot
Default
None
Command mode
Privileged EXEC mode
Syntax
shoe sys software
Default
Command mode
Privileged EXEC mode
show tacacs
Display the status of the TACACS+ configuration.
Syntax
show tacacs
Default
None
Command mode
Privileged EXEC mode
show tech
Use this command to display technical information about system status and information about the hardware, software, and
operation of the switch.
Syntax
show tech
Default
None
Command mode
Privileged EXEC mode
show telnet-access
Display the Telnet access configuration information on your switch.
Syntax
show telnet-access
Default
None
Command mode
Privileged EXEC mode
Syntax
show test all WORD<1-99>
Default
None
Command mode
Privileged EXEC mode
Syntax
show test artable
Default
None
Command mode
Privileged EXEC mode
Syntax
show test fabric
Default
None
Command mode
Privileged EXEC mode
show trace
Display trace information.
Syntax
show trace [auto] [ethernet] [file] [level] [modid-list] [syslog]
Default
None
Command mode
Privileged EXEC mode
show users
Use this command to display a list of users who are logged on to the switch.
Syntax
show users
Default
None
Command mode
Privileged EXEC mode
Syntax
show vlacp interface
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
fastethernet [vid Displays the VLACP configuration for the Fastethernet port interface. vlan-
{vlan-id[-vlan- id is the VLAN ID or list of VLAN IDs to show only ports attached to a
id][,...]}]
[<portList>] particular VLAN. The range is 14094. portList is the port or port list.
gigabitethernet Displays the VLACP configuration for the GigabitEthernet port interface.
[vid {vlan-id[- vlan-id is the VLAN ID or list of VLAN IDs to show only ports attached to a
vlan-id][,...]}]
[<portList>] particular VLAN. The range is 14094. portList is the port or port list.
pos [vid {vlan-id[- Displays the VLACP configuration for the PoS port interface. vlan-id is the
vlan-id][,...]}] VLAN ID or list of VLAN IDs to show only ports attached to a particular
[<portList>] VLAN. The range is 14094. portList is the port or port list.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show vlan advance
Syntax
show vlan advance [<1-4094>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
port <value> Specifies the port or range of ports.
<1-4094> Specifies the VLAN ID in a range of 1 to 4094.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show vlan autolearn-mac
Syntax
show vlan autolearn-mac
Default
None
Command mode
Privileged EXEC mode
Syntax
show vlan basic <1-4094>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-4094> Specifies the VLAN ID in a range of 1 to 4094.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show vlan brouter-port
Syntax
show vlan brouter-port <portList>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<portList> Specifies the slot and the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show vlan dvmrp
Syntax
show vlan dvmrp <1-4094>
Default
None
Command mode
Privileged EXEC mode
Syntax
show vlan idsvlan <1-4094> [port <slot/port>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<1-4094> Specifies the VLAN ID in a range of 1 to 4094.
port <slot/port> Specifies the port or range of ports in a slot/port format.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show vlan i-sid
Syntax
show vlan i-sid [<vid>]
Default
None
Command mode
User EXEC mode
Command parameters
Parameter Description
[<vid>] Specifies the VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show vlan mac-address-
entry
Syntax
show vlan mac-address-entry
Default
None
Command mode
User EXEC mode
Syntax
show vlan mac-address-filter [<1-4094>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
mac <value> Specifies the MAC address.
port <portList> Specifies the port or range of ports in a slot/port format.
<1-4094> Specifies the VLAN ID in a range of 1 to 4094.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show vlan mac-address-
static
Syntax
show vlan mac-address-static [<1-4094>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
mac <value> Specifies the MAC address.
port <portList> Specifies the port or range of ports in either slot or port format.
<1-4094> Specifies the VLAN ID in a range of 1 to 4094.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show vlan manual-edit-mac
Syntax
show vlan manual-edit-mac
Default
None
Command mode
Privileged EXEC mode
Syntax
show vlan members <portList>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Specifies the port or range of ports.Important Entering a port <value> is optional. When
port you enter a port <value>, the command shows information for the specified VLAN or
<value> port. Without the port <value>, the command shows information for all the configured
VLANs.
Specifies the VLAN ID in the range of 1 to 4094.Important Entering a vid is optional.
<1-4094> When you enter a vid command shows information for the specified VLAN or port.
Without the vid the command shows information for all the configured VLANs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show vlan nodal-mep
Syntax
show vlan nodal-mep <vid>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<vid> Specifies the VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show vlan nodal-mip-level
Syntax
show vlan nodal-mip-level <vid>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<vid> Specifies the VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show vlan remote-mac-table
Syntax
show vlan remote-mac-table <vid>
Default
None
Command mode
User EXEC mode
Command parameters
Parameter Description
[<vid>] Specifies the VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show vlan srcmac
Syntax
show vlan srcmac <1-4094> [port <portList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Specifies the port or range of ports.Important The entry of a port <value> is optional.
<portList> Aport <value> command shows information for the specified VLAN or port. Without
port port <value>, the command information is shown for all the configured VLANs.
Specifies the VLAN ID. The value ranges from 1 to 4094.Important The entry of a vid is
<1-4094> optional. When you enter a vid command shows information for the specified VLAN or
port. Without the vid the command shows information for all the configured VLANs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show vlan static-mcastmac
Syntax
show vlan static-mcastmac [<vlan 1-4904>]
Default
None
Command mode
Privileged EXEC mode
show web-server
Display the Web Server information if Web Server is enabled.
Syntax
show web-server
Default
None
Command mode
User EXEC mode
Syntax
show wireless switch
Default
None
Command mode
Privileged EXEC mode
Syntax
show wireless-switch lb-controller [<A.B.C.D>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show wireless-switch mac-address-entry [vid <value>] [mac <value>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[vid Displays information for all of the FDB entries configured on this switch or for a
<value>] specific VLAN ID.
[mac Displays information for all of the FDB entries configured on this switch or for a
<value>] specific MAC address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show wireless switch peer-
advertized-vlans
Syntax
show wireless switch peer-advertized-vlans {by-advertizer | by-vlan}
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
by- Displays the Mobility VLANs for all the peer WSPs. You can display the table of VLANs
advertizer by-advertizer.
by-vlan Displays the Mobility VLANs for all the peer WSPs. You can display the table of VLANs
by-vlan.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show wireless-switch peer-
devices
Syntax
show wireless-switch peer-devices [ap] [switch]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
[ap] Displays configuration information for all of the WSP peer devices or just for the access
(ap) or mobility tunnels (switch).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show wireless-switch tunnel
Syntax
show wireless-switch tunnel [<tunnelIntfId>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<tunnelIntfId> Displays configuration information for all of the tunnels configured on this switch
or for a specific tunnel.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show wireless-switch
tunnel-statistics
Syntax
show wireless switch tunnel-statistics [<tunnelIdList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<tunnelIntfId> Displays the statistics for all of the tunnels configured on this switch or for a
specific tunnel.
bridging Displays the bridging statistics for all of the tunnels configured on this switch
<tunnelIntfId> or for a specific tunnel.
keepalive Displays the keepalive statistics for all of the tunnels configured on this
<tunnelIntfId> switch or for a specific tunnel.
routing Displays the routing statistics for all of the tunnels configured on this switch
<tunnelIntfId> or for a specific tunnel.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show wireless-switch
tunnel-statistics bridging
Syntax
show wireless switch tunnel-statistics bridging [<tunnelIdList>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show wireless switch tunnel-statistics keepalive [<tunnelIdList>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show wireless switch tunnel-statistics routing [<tunnelIdList>]
Default
None
Command mode
Privileged EXEC mode
Syntax
show wireless-switch vlan-map [<name:WORD 0-32>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<name:WORD Displays configuration information for all of the VLAN maps on this switch or for a
0-32> specific VLAN map.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show wireless-switch vlan-
reservation
Syntax
show wireless-switch vlan-reservation [<vidList>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
<vidList> Displays information for all of the reserved VLAN IDs or for a specific VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:show wireless-switch vlan-
servers
Syntax
show wireless-switch vlan-servers
Default
None
Command mode
Privileged EXEC mode
shutdown
Disable the SF/CPU module when it is not functioning. When used in FastEthernet or GigabitEthernet configuration mode, disables
an Ethernet module before you remove it from the chassis to minimize traffic loss. Traffic does not flow on a disabled module.
Syntax
shutdown <1-10>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-10> Specifies the slot number of the module to be disabled. SF/CPUs can reside in slots 5 and
6 in the six and ten-slot chassis.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:slot reset
slot reset
Use the following command after all modules are updated, for the updates to take effect on the switch.
Syntax
slot reset <slotList>
Default
Command mode
Global configuration mode
Command parameters
Parameter Description
<slotlist> Specifies the slot number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:slpp enable
slpp enable
Enable the Simple Loop Prevention Protocol (SLPP) globally and on a VLAN to detect a loop and automatically stop it.
Syntax
slpp enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the SLPP operation globally an on a VLAN.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:slpp ethertype
slpp ethertype
Specify the PDU Ether type on the SLPP.
Syntax
slpp ethertype <pid>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the SLPP PDU Ethernet type. <pid> is the SLPP protocol ID in integer format
ethertype
<pid> from 165535. To set this option to the default value, use the default operator with the
command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:slpp port
slpp port
Enable SLPP by port to detect a loop and automatically stop it.
Syntax
slpp port <portlist> [packet-rx] [packet-rx-threshold <1-500>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
packet-rx Activates SLPP packet reception on the listed ports. To set this option to the default
value, use the default operator with the command.
<portlist> Identifies the slot or port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:slpp tx-interval
slpp tx-interval
Configure the transmission interval on the SLPP.
Syntax
slpp tx-interval <integer>
Default
The default is 500.
Command mode
Global configuration mode
Command parameters
Parameter Description
tx-interval Configures the SLPP packet transmit interval. <integer> is the SLPP packet
<integer> transmit interval. The range is 5005000 milliseconds.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:slpp vid
slpp vid
Add a VLAN to a SLPP transmission list.
Syntax
slpp vid <vid>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
vid <vid> Adds a VLAN to a SLPP transmission list. <vid> is the VLAN ID from 14095.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:smlt
smlt
Create a SMLT from an existing MLT to split physical ports between two switches to improve resiliency and provide active load
sharing.
Syntax
smlt <smltid>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<smltid> Specifies the Split MLT ID in the range of 1256. The value must match the peer switch
SMLT ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:smlt port
smlt port
Configure a split MultiLink trunk that uses a single port. Use single port SMLT to permit the scaling of the number of SMLT on a
switch to the maximum number of available ports.
Syntax
smlt <smlt id>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<smltid> Specifies the Split MLT ID. The value ranges from 1512.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:snmplog
snmplog
Use SNMP trap logging to send a copy of all traps to the PCMCIA card.
Syntax
snmplog enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables or disables the logging of traps.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:snmp-server
snmp-server
Configure Simple Network Management Protocol (SNMP) to define or modify the SNMP settings, and specify how secure you want
SNMP communications.
Syntax
snmp-server
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
contact <word> Identifies the contact person who manages the node. To include blank spaces in
the contact, use quotation marks (") around the text.
agent- Activates agent conformance mode. Use the no operator to disable this
conformance configuration. To set this option to the default value, use the default operator
enable with the command.
Activates the generations of authentication traps. Use the no operator to disable
authentication-
trap enable this configuration. To set this option to the default value, use the default
operator with the command.
Creates an initial set of configuration data for SNMPv3. This configuration data
follows the conventions described in the SNMPv3 standard (see RFC 3515,
Appendix A). This command creates a set of initial users, groups, and views.
min-secure-a minimum security configuration that allows read access and notify
access to all processes (MIB view restricted) with noAuth-noPriv and read, write,
and notify access to all processes (MIB view internet) using Auth-Priv. In this
bootstrap configuration, restricted MIB view matches internet MIB view. semi-secure-a
<min-secure|
semi-secure| security configuration that allows read access and notify access to all processes
very-secure> (MIB view restricted) with noAuth-noPriv and read, write, and notify access to all
processes (MIB view internet) using Auth-Priv. In this configuration, restricted
MIB view contains a smaller subset of views than internet MIB view. See RFC
3515 Appendix A for details. very-secure-a maximum security configuration that
allows no access to the users. Note that with this command all existing SNMP
configurations in the SNMPv3 MIB tables are removed and replaced with entries
as described in the RFC.
contact <WORD Changes the sysContact information for the switch. <WORD 0-255> is an ASCII
0-255> string from 0255 characters (for example a phone extension or email address).
disable Disable SNMP globally for the entire system.
enable Enable SNMP globally for the entire system.
Configures the SNMP and IP sender flag to the same value. The default is
force-iphdr-
sender enable disable. Use the no operator to remove this configuration. To set this option to
the default value, use the default operator with the command.
Sends the configured source address (sender IP) as the sender network in the
force-trap-
sender enable notification message. Use the no operator to remove this configuration. To set
this option to the default value, use the default operator with the command.
location <WORD Changes the sysLocation information for the switch. <WORD 0-255> is an ASCII
0-255> string from 0255 characters.
Configure the SNMP logging. Specify:enable to enable the SNMP log feature.
log {enable | maxfilesize <64-256000> to set the maximum SNMP log file size in KB. Use the
maxfilesize
<64-256000>} no operator to remove this configuration. To set this option to the default value,
use the default operator with the command.
name <WORD 0- Changes the sysName information for the switch. <WORD 0-255> is an ASCII
255> string from 0255 characters.
Configures the SNMP trap receiver and source IP addresses. Specify the IP
address of the destination SNMP server that will receive the SNMP trap
sender-ip notification in the first IP address. Specify the source IP address of the SNMP
<A.B.C.D>
<A.B.C.D> trap notification packet that is transmitted in the second IP address. If this is set
to 0.0.0.0 then the switch uses the IP address of the local interface that is
closest (from an IP routing table perspective) to the destination SNMP server.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:snmp-server community
snmp-server community
Create a community to use in forming a relationship between an SNMP agent and one or more SNMP managers.
Syntax
snmp-server community <name> [group <WORD>] [index <WORD>] [secname <WORD>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
group <WORD> Specifies the group name. The range is 132 characters.
index <WORD> Specifies the unique index value of a row in this table. The range is 132
characters.
<name> Specifies a community string, from 132 characters.
secname Maps the community string to the security name in the VACM Group Member
<WORD> Table.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:snmp-server group
snmp-server group
Create a new user group member to logically group users who require the same level of access.
Syntax
snmp-server group <group name> <context name> [auth-no-priv|auth-priv|no-auth-no-priv]
[notify-view <WORD>] [read-view <WORD>] [write-view <WORD>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
auth-no- Assigns the minimum level of security required to gain the access rights allowed by this
priv conceptual row. If the auth-no-priv parameter is included, it creates one entry for
SNMPv3 access.
Assigns the minimum level of security required to gain the access rights allowed by this
auth-
priv conceptual row. If the auth-priv parameter is included, it creates one entry for SNMPv3
access.
Creates a group entry for a particular context. The range is 032 characters. If you use a
particular group name value but with different context names, you create multiple entries
for different contexts for the same group. You can omit the context name and use the
<context
name> default. If the context name value ends in the wildcard character (*), the resulting entries
match a context name that begins with that context. For example, a context name value
of foo* matches contexts starting with foo, such as foo6 and foofofum. Use the no
operator to remove this configuration.
group Assigns the group name for data access. The range is 132 characters. Use the no
<group
name> operator to remove this configuration.
no-auth- Assigns the minimum level of security required to gain the access rights allowed by this
no-priv conceptual row. If the no-auth-no-priv parameter is included, it creates 3 entries, one for
SNMPv1 access, one for SNMPv2c access, and one for SNMPv3 access.
notify-
view Specifies the view name in the range of 032 characters.
<WORD>
read-
view Specifies the view name in the range of 032 characters.
<WORD>
write-
view Specifies the view name in the range of 032 characters.
<WORD>
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:snmp-server host v1
snmp-server host v1
Configure an SNMP host so that the switch can forward SNMP traps to a host for monitoring.
Syntax
snmp-server host <WORD 1-256> port <1-65535> v1 <WORD 1-32> [filter <WORD 1-32>] [target-
name <WORD 1-32>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Word <1-256> Specifies either an IPv4 or IPv6 address.
port <1-65535> Specifies the host server port number.
v1 <WORD 1-32> Creates a new SNMPv1 entry for the target address table.<WORD 1-32>
[filter <WORD specifies the security name, which identifies the principal that generates SNMP
1-32>] [target-
name <WORD 1- messages. filter <WORD 1-32> specifies the filter profile to use. target-name
32>] <WORD 1-32> is the target name with a string length of 1 to 32.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:snmp-server host v2
snmp-server host v2
Configure an SNMPv2 host so that the switch can forward SNMP traps to a host for monitoring.
Syntax
snmp-server host <WORD 1-256> port <1-65535> v2c <WORD 1-32> [inform [mms <0-2147483647>]
[retries <0-255>] [timeout <0-2147483647>]] [filter <WORD 1-32>] [target-name <WORD 1-32>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
v2c <WORD 1-32> Creates a new SNMPv2c entry for the target address table.<WORD 1-32>
[inform [mms
<0-2147483647>] specifies the security name, which identifies the principal that generates SNMP
[retries <0- messages. inform indicates that SNMP notifications should be sent as inform
255>] [timeout (rather than trap). mms <0-2147483647> specifies the maximum message size
<0- as an integer with a range of 1 to 2147483647. retries <0-255> specifies the
2147483647>]] retry count value with a range of 0 to 255. timeout <0-2147483647> specifies
[filter <WORD the timeout value in seconds with a range of 0 to 214748364. filter <WORD 1-
1-32>] [target- 32> specifies the filter profile to use. target-name <WORD 1-32> is the target
name <WORD 1-
32>] name with a string length of 1 to 32.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:snmp-server host v3
snmp-server host v3
Configure an SNMPv3 host so that the switch can forward SNMP traps to a host for monitoring.
Syntax
snmp-server host <WORD 1-256> port <1-65535> v3 {noAuthnoPriv|authNoPriv|AuthPriv} <WORD 1-
32> [inform [retries <0-255>] [timeout <0-2147483647>]] [filter <WORD 1-32>] [target-name
<WORD 1-32>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Creates a new SNMPv3 entry for the target address
table.{noAuthnoPriv|authNoPriv|AuthPriv} specifies the
security level. <WORD 1-32> specifies the security
v3 name, which identifies the principal that generates
{noAuthnoPriv|authNoPriv|AuthPriv} SNMP messages. inform indicates that SNMP
<WORD 1-32> [inform [retries <0- notifications should be sent as inform (rather than
255>] [timeout <0-2147483647>]] trap). retries <0-255> specifies the retry count value
[filter <WORD 1-32>] [target-name with a range of 0 to 255. timeout <0-2147483647>
<WORD 1-32>] specifies the timeout value in seconds with a range of 0
to 214748364. filter <WORD 1-32> specifies the filter
profile to use. target-name <WORD 1-32> is the
target name with a string length of 1 to 32.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:snmp-server notify-filter
snmp-server notify-filter
Configure the notify table to select management targets to receive notifications, as well as the type of notification to send to each
management target.
Syntax
snmp-server notify-filter <WORD 1-32> <WORD 1-32>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<WORD 1- Creates a notify filter table.<WORD 1-32> specifies the name of the filter profile with a
32> string length of 1 to 32. The second <WORD 1-32> identifies the filter subtree OID with
<WORD 1- a string length of 1 to 32. If the Subtree OID parameter uses a '+' prefix (or no prefix),
32> this indicates include. If the Subtree OID uses the - prefix, this indicates exclude.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:snmp-server sender-ip
snmp-server sender-ip
Configure the IP interface from which the SNMP traps originate if the Avaya Ethernet Routing Switch 8800/8600 has multiple
interfaces.
Syntax
snmp-server sender-ip <A.B.C.D> <A.B.C.D>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Configures the SNMP trap receiver and source IP addresses. Specify the IP address of
sender- the destination SNMP server that will receive the SNMP trap notification in the first IP
ip address. Specify the source IP address of the SNMP trap notification packet that is
<A.B.C.D> transmitted in the second IP address. If this is set to 0.0.0.0 then the switch uses the IP
<A.B.C.D> address of the local interface that is closest (from an IP routing table perspective) to the
destination SNMP server.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:snmp-server user
snmp-server user
Create a user on the local system in the USM table to authorize a user on a particular SNMP engine.
Syntax
snmp-server user <WORD> [read-view <WORD>] [write-view <WORD>] [notify-view <WORD>]
[{md5|sha} <password>] [read-view <WORD>] [write-view <WORD>] [notify-view <WORD>]
[{aes|des|3des} <password> [read-view <WORD>] [write-view <WORD>] [notify-view <WORD>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies a privacy protocol. If no value is entered, no authentication capability
{aes|des|3des} exists. The choices are aes, des, or 3des. password assigns a privacy password. If
<password> no value is entered, no privacy capability exists. The range is 1 to 32 characters.
Important You must set authentication before you can set the privacy option.
Specifies an authentication protocol. If no value is entered, no authentication
{md5|sha} capability exists. The protocol choices are MD5 and SHA. password specifies an
<password> authentication password. If no value is entered, no authentication capability
exists. The range is 132 characters.
Specifies the view name in the range of 0-32 characters. The first instance is a
notify-view
<WORD> noAuth view. The second instance is an auth view and the last instance is an
authPriv view.
Specifies the view name in the range of 0-32 characters. The first instance is a
read-view
<WORD> noAuth view. The second instance is an auth view and the last instance is an
authPriv view.
Specifies the view name in the range of 0-32 characters. The first instance is a
write-view
<WORD> noAuth view. The second instance is an auth view and the last instance is an
authPriv view.
Creates the new entry with this security name. The name is used as an index to
user <WORD> the table. The range is 132 characters. Use the no operator to remove this
configuration.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:snmp-server user engine-id
Syntax
snmp-server user engine-id <WORD 16-97> <WORD 1-32> {md5|sha} <WORD 1-32> <password>]
[{aes|des} <WORD 1-32>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
{aes|des} Specifies a privacy protocol. If no value is entered, no authentication capability exists.
<Word 1- The choices are aes or des. Word 1-32 assigns a privacy password. If no value is
32> entered, no privacy capability exists. The range is 1 to 32 characters.
engine-id Assigns an SNMPv3 engine ID. The range is 1064 characters. Use the no operator to
<WORD> remove this configuration.
Specifies an authentication protocol. If no value is entered, no authentication capability
{md5|sha} exists. The protocol choices are MD5 and SHA. password specifies an authentication
<password> password. If no value is entered, no authentication capability exists. The range is 132
characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:snmp-server user group
Syntax
snmp-server user <WORD> group <WORD> [{md5|sha} <password>] [{aes|des} <password>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies a privacy protocol. If no value is entered, no authentication capability exists.
{aes|des} The choices are aes or des. password assigns a privacy password. If no value is
<password> entered, no privacy capability exists. The range is 1 to 32 characters. Important You
must set authentication before you can set the privacy option.
group
<WORD> Specifies the group access name.
Specifies an authentication protocol. If no value is entered, no authentication capability
{md5|sha} exists. The protocol choices are MD5 and SHA. password specifies an authentication
<password> password. If no value is entered, no authentication capability exists. The range is 132
characters.
user Creates the new entry with this security name. The name is used as an index to the
<WORD> table. The range is 132 characters. Use the no operator to remove this configuration.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:snmp-server view
snmp-server view
Create a new entry in the MIB view table. The default Layer 2 MIB view cannot modify SNMP settings. However, a new MIB view
created with Layer 2 permission can modify SNMP settings.
Syntax
snmp-server view <view name> <subtree oid>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<subtree Specifies the prefix that defines the set of MIB objects accessible by this SNMP entity.
oid> The range is 132 characters.
<view
name> Specifies a new entry with this group name. The range is 132 characters.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:source file
source file
Source a configuration to merge a script file into the running configuration.
Syntax
source <file> [stop] [debug] [syntax]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
debug Debugs the script output.
file Specifies a file name and location from 199 characters. Use the format
{a.b.c.d:|peer:|/pcmcia/|/flash/}<file>
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spanning-tree mstp msti
Syntax
spanning-tree mstp msti <1-63> priority <0-65535>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<1-63> Specifies the instance parameter.
priority Sets the MSTP bridge priority. Allowed values are 4096, 8192, 12288, 16384, 20480,
<0-65535> 24576, 28672, 32768, 36864, 40960, 45056, 49152, 53248, 57344, 61440.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spanning-tree rstp version
Syntax
spanning-tree rstp version <stp-compatible|rstp>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
version <stp- Sets the RSTP version to either of the following:stp-compatible
compatible|rstp> rstp
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spanning-tree stp
spanning-tree stp
Set a tagged bridge protocol data unit (BPDU) address different from the standardized BPDU address and create an sVLAN
Spanning Tree Group (STG).
Syntax
spanning-tree stp <1-64> create type <stgsvlan|stgnormal> ntstp enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
create type Creates a new STG. type sets the STG to normal or sVLAN. Choices are stgsvlan or
stgsvlan
ntstp stgnormal. ntstp enables or disables NTSTP. Choices are enable or disable.
enable Enables STP.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spanning-tree stp change-
detection
Syntax
spanning-tree stp <1-64> change-detection
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
change- Enables or disables topology change detection for the specified spanning tree. The
detection default is enable.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spanning-tree stp create
Syntax
spanning-tree stp <1-64> create [<ports>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
create Creates a new STG: ports specifies one or more slot/port numbers. Ports cannot be
[<ports>] added to the STG if configured as Single Port SMLT, or as a member of another STG.
tagged- Specifies the tagged bridged protocol data unit VLAN ID. If a VLAN spans multiple
bpdu-vid
<value> switches, it must be within the same STG across all switches.
multicast-
address Specifies the multicast address.
<value>
type
<value> type <value> is the type of STG. Choices are stgnormal or stgsvlan.
ntstp
<value> ntstp <value> enables or disables STP. Choices are enable or disable.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spanning-tree stp trap-stp
Syntax
spanning-tree stp <1-64> ports <portList> trap-stp
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
trap-stp Enables STP trap for a specific STG.
<portList> Specifies the port list.
<1-64> Specifies the spanning tree ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spbm
spbm
Enable Shortest Path Bridging MAC (SPBM) globally. When used in IS-IS configuration mode, creates the Shortest Path Bridging
MAC (SPBM) instance. In this release, only one SPBM instance is supported.
Syntax
[no] [default] spbm <inst>
Default
The default is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
[no] Use the no option to disable SPBM globally.
[default] Use the default option to disable SPBM globally.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spbm b-vid
spbm b-vid
Add the SPBM B-VLAN to the SPBM instance.
Syntax
[no] spbm <inst> b-vid {<vlan-id [-vlan-id] [,...]}[primary <vid>]
Default
None
Command mode
Router IS-IS configuration mode
Command parameters
Parameter Description
[no] Use the no option to remove the specified B-VLAN from the SPBM
instance.
<inst> Specifies the SPBM instance ID.
{<vlan-id [-vlan-id]
[...]} Specifies the B-VLANs to add to the SPBM instance.
[primary<vid>] Specifies the primary B-VLAN on the SPBM instance.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spbm ethertype
spbm ethertype
Configure the SPBM ethertype.
Syntax
spbm ethertype {0x8100 | 0x88a8}
Default
The default value is 0x8100.
Command mode
Global configuration mode
Command parameters
Parameter Description
{0x8100 | 0x88a8} Specifies the SPBM ethertype.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spbm ip enable
spbm ip enable
Configure SPBM Native IP shortcuts.
Syntax
[no] [default] spbm <inst> ip enable
Default
The default is disabled.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
no Disable SPBM Native IP shortcuts.
default Disable SPBM Native IP shortcuts.
<inst> Specifies the SPBM instance ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spbm lsdb-trap enable
Syntax
[no] [default] spbm <inst> lsdb-trap enable
Default
The default is disable.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
no Use the no option to disable LSDB traps.
default Use the default option to disable LSDB traps.
<inst> Specifies the SPBM instance ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spbm nick-name
spbm nick-name
Configure the system nickname (2.5 bytes in the format <x.xx.xx>).
Syntax
[no] [default] spbm <inst> nick-name
Default
None
Command mode
Router IS-IS configuration mode
Command parameters
Parameter Description
[no] Use the no option to delete the configured nickname.
[default] Use the default option to delete the configured nickname.
<inst> Specifies the SPBM instance ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spbm smlt-peer-system-id
spbm smlt-peer-system-id
Specify the system ID of the SPBM SMLT peer.
Syntax
spbm <ins> smlt-peer-system-id <xxxx.xxxx.xxxx>
Default
None
Command mode
Router IS-IS configuration mode
Command parameters
Parameter Description
<inst> Specifies the SPBM instance.
smlt-peer-system-id Specifies the system ID of the SMLT peer in 6
<xxxx.xxxx.xxxxr> bytes.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spbm smlt-virtual-bmac
spbm smlt-virtual-bmac
Configure the virtual-BMAC, which is shared and advertised by both peers.
Syntax
spbm <inst> smlt-virtual-bmac <virtual-mac>
Default
None
Command mode
Router IS-IS configuration mode
Command parameters
Parameter Description
<inst> Specifies the SPBM instance.
smlt-virtual-bmac<virtual- Specifies a virtual MAC address that can be used by both
bmac> peers.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spb-multicast enable
spb-multicast enable
Use this command to configure the VLAN level.
Syntax
<spb-multicast | no ip spb-multicast> enable
Default
None
Command mode
Interface configuration mode
Command parameters
Parameter Description
spb-multicast | no ip spb- Enables or disables IP multicast over SPBM on the
multicast VLAN.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:speed
speed
Set the speed of the port on the Ethernet modules.
Syntax
speed [port <portList>] <10|100|1000>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<10|100|1000> Specifies the port speed. Not applicable to 1 Gigabit or 10 Gigabit Ethernet
modules.
port Specifies the slot and the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spf-delay
spf-delay
Specify the SPF delay in milliseconds. This value is used to pace successive SPF runs. The timer prevents two SPF runs from being
scheduled very closely.
Syntax
[no] [default] spf-delay <spf-delay-time>
Default
The default is 100 milliseconds.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value of 100 milliseconds.
default Use the default option to set this parameter to the default option of 100
milliseconds.
<spf-delay-
time> Specify the SPF delay time in milliseconds, range of 05000 ms.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:spoof-detect portlist enable
Syntax
spoof-detect [port <portList>] [enable]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables spoof detection on the port.
<portList> Specifies the port list.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:ssh
ssh
Set Secure Shell (SSH) configuration parameters to support public and private key encryption connections.
Syntax
ssh
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
dsa-auth Enable or disable the DSA authentication.
secure Enables SSH in secure mode and immediately disables the access services SNMP,
FTP, TFTP, rlogin, and Telnet.
max-sessions
<0-8> The maximum number of SSH sessions allowed. A value from 0 to 8. Default is 4.
pass-auth Enables password authentication.
Sets the SSH connection port. <1-65535> is the port number. The default is 22
port <1-
65535> Important You cannot configure the following TCP ports as SSH connection ports:
Ports 0 to 1024 (except port 22),1100, 4095, 5000, 5111, 6000, or 999.
rsa-auth Enable RSA authentication.
timeout <1-
120> The SSH connection authentication timeout in seconds. Default is 60 seconds.
version Sets the SSH version. Default is v2only. Important Avaya recommends setting the
<v2only|both> version to v2 only.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:svlan
svlan
Set the Ethertype to indicate which protocol is transported in an Ethernet frame and to set the switch level associated with this
sVLAN.
Syntax
svlan
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
ether-type Sets level and corresponding ethertype for svlan.
level Sets the svlan level.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:svlan-porttype
svlan-porttype
Set the sVLAN port type to sVLAN UNI or sVLAN NNI.
Syntax
svlan-porttype [port <portList> ] <uni|nni|normal>;default svlan-porttype [port <portList>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Sets the port type for the sVLAN to normal, user-to-network interface (UNI), or
network-to-network interface (NNI). The default is normal.Important Designate
all ports within an OctaPID as either normal or sVLAN (that is, the ports can be
<normal|uni|nni> all Normal or a combination of UNI/NNI within the Octapid, which can be up to
eight ports). When you configure a UNI port in the CLI, the tagged-frames-
discard parameter is automatically enabled. When you configure an NNI port in
the CLI, the untagged-frames-discard parameter is automatically enabled.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:synchronization
synchronization
Enable the router to accept routes from BGP peers without waiting for an update from the IGP.
Syntax
synchronization
Default
The default value is enable.
Command mode
Global configuration mode
Syntax
sys 8648gtr high-priority-control-mac <0-5> [<0x00:0x00:0x00:0x00:0x00:0x00>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<0-5> specifies the MAC address register and ranges
<0-5> from 0 to 5. <0x00:0x00:0x00:0x00:0x00:0x00>
[<0x00:0x00:0x00:0x00:0x00:0x00>] specifies the MAC address to be given high priority. If no
MAC address is specified, it is set to default.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys action
sys action
Reset system functions to reset all statistics counters, the modem port, the console port, and the operation of the switchover
function.
Syntax
sys action cpu-switch-over
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
cpuswitchover Resets the switch to change over to the backup SF/CPU.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys action cpu-switch-over
Syntax
sys action cpu-switch-over
Default
Command mode
Global configuration mode
Command parameters
Parameter Description
cpu-switch-over Switches over to the other CPU.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys ecn-compatibility
sys ecn-compatibility
Enable explicit congestion notification to configure global options for the Ethernet Routing Switch 8800/8600.
Syntax
sys ecn-compatibility
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Activates explicit congestion notification, as defined in Experimental Request For
ecn-
compatibility Comments (RFC) 2780. This feature is not currently supported on the Ethernet
Routing Switch 8800/8600.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys ext-cp-limit max-ports-
to-check
Syntax
sys ext-cp-limit [max-ports-to-check <value>]
Default
The default is 0.
Command mode
Global configuration mode
Command parameters
Parameter Description
max-ports-to- Configures the total number of ports to monitor. number of ports is in the
check <number range of 0512. To set this option to the default value, use the default
of ports> operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys ext-cp-limit min-
congestion-time
Syntax
sys ext-cp-limit [min-congestion-time <time>]
Default
The default is 300.
Command mode
Global configuration mode
Command parameters
Parameter Description
min- Configures the minimum time for which traffic keeps hitting the SF/CPU to trigger the
congestion- congestion algorithm. time in msec is the time in milliseconds in the range of 100
time <time 600000. To set this option to the default value, use the default operator with the
in msec> command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys ext-cp-limit port
Syntax
sys ext-cp-limit port <PortList> <None|SoftDown|HardDown>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Indicates the following:None-the port does not need to be checked.
<None|SoftDown|HardDown> SoftDown-the port belongs to the may-go-down-port-list.
HardDown-the port belongs to the must-go-down-port-list.
port <PortList> Specifies a port or list of ports.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys ext-cp-limit port-
congestion-time
Syntax
sys ext-cp-limit [port-congestion-time <time>]
Default
The default is 5 seconds.
Command mode
Global configuration mode
Command parameters
Parameter Description
port- Configures the time duration for which, if the bandwidth utilization for a monitoring
congestion- port remains more than the threshold, the port is disabled. time in sec is the time in
time <time seconds in the range of 1600. To set this option to the default value, use the default
in sec> operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys ext-cp-limit trap-level
Syntax
sys ext-cp-limit trap-level <dummy|None|Normal|Verbose>
Default
The default value is None.
Command mode
Global configuration mode
Command parameters
Parameter Description
Configures the trap level. The options are: dummy None-no
traps are sent. Normal-sends a single trap for all the ports which
trap-level
<dummy|None|Normal|Verbose> are disabled. Verbose-sends a trap for each of the ports which is
disabled. To set this option to the default value, use the default
operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys flags enhanced-
operational-mode
Syntax
sys flags enhanced-operational-mode
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enhanced-operational- Sets the enhanced operation mode to increase the maximum number
mode of VLANs.
global-filter-ordering Enables global filter ordering feature.
multicast-check-packet Enables multicast check packet feature on PR.
vlan-optimization-mode Enable VLAN rec optimization mode-effect after reboot.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys flags global-filter-
ordering
Syntax
sys flags global-filter-ordering
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
global-filter- Enables the global filter ordering feature on the Ethernet Routing Switch
ordering 8800/8600.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys force-msg
sys force-msg
Use the force message control option to extend the message control feature functionality to the software and hardware log
messages.
Syntax
sys force-msg WORD <4-4>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Adds a forced message control pattern WORD is a string of 4 characters. You can add a
force-
msg WORD four-byte pattern into the force-msg table. The software and the hardware log messages
<4-4> that use the first four bytes matching one of the patterns in the force-msg table undergo
the configured message control action.
Used to add a forced message control pattern, where <WORD 4-4> is a string of 4
characters. You can add a four-byte pattern into the force-msg table. The software and
<WORD 4- the hardware log messages that use the first four bytes matching one of the patterns in
4> the force-msg table undergo the configured message control action. You can specify up
to 32 different patterns in the force-msg table. This includes a wildcard pattern (****) as
well. Upon specifying the wildcard pattern, all messages undergo message control.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys global-filter
sys global-filter
Enable global filtering on Ethernet Routing Switch 8800/8600.
Syntax
sys global-filter
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Activates global filtering on the switch. After this command is activated, you must disable
global- source MAC VLANs. You cannot enable global filtering and source MAC-based VLANs at
filter the same time. This command is available only on the Ethernet Routing Switch
8800/8600 E and M modules.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys hash-calc getmltindex
traffic-type
Syntax
sys hash-calc getmltindex traffic-type <ipv4|ipv6|non-ip> dest-val <WORD 1-1536> src-val
<WORD 1-1536> mltID <1-256> [dest-port <0-65535>] [src-port <0-65535>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
dest-val<value> Specifies the destination address in the range form 11536. The source and
destination addresses cannot have the same value.
src-val<value> Specifies the source address in the range from 11536. The source and
destination addresses cannot have the same value.
mltID<value> Specifies the MLT ID. The value ranges from 1256.
traffic-type
{ipv4|ipv6|non-ip} The type of traffic. Specify one of ipv4, ipv6, or non-ip.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:syslog enable
syslog enable
The syslog commands control a facility in UNIX machines that logs SNMP messages and assigns each message a severity level
based on importance.
Syntax
syslog enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the sending of syslog messages on the switch.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:syslog host
syslog host
The syslog commands control a facility in UNIX machines that logs SNMP messages and assigns each message a severity level based on importance.
Syntax
syslog host <1-10>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<cr> Creates a syslog host instance.
Configures a host location for the syslog host.
address <A.B.C.D> <A.B.C.D> is the IP address of the UNIX system
syslog host.
Specifies the UNIX facility used in messages to the
syslog host.
facility
{local0|local1|local2|local3|local4|local5|local6|local7} {local0|local1|local2|local3|local4|local5|local6|local7}
is the UNIX system syslog host facility (LOCAL0 to
LOCAL7).
enable Enables the syslog host.
maperror Specifies the syslog severity to use for Error
{emergency|alert|critical|error|warning|notice|info|debug} messages.
mapfatal Specifies the syslog severity to use for Fatal
{emergency|alert|critical|error|warning|notice|info|debug} messages.
mapinfo Specifies the syslog severity level to use for
{emergency|alert|critical|error|warning|notice|info|debug} Information messages.
mapwarning Specifies the syslog severity to use for Warning
{emergency|alert|critical|error|warning|notice|info|debug} messages.
severity <info|warning|error|fatal> Specifies the severity levels for which syslog
[<info|warning|error|fatal>] [<info|warning|error|fatal>]
[<info|warning|error|fatal>] messages should be sent for the specified modules.
Specifies the UDP port number on which to send
udp-port <514-530> syslog messages to the syslog host. This is the UNIX
system syslog host port number (514 to 530).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys max-vlan-resource-
reservation
sys max-vlan-resource-reservation
Enable maximum VLAN mode to use all available Multicast Group IDs (MGIDs) for VLANs. No IP multicast (IPMC) traffic transmits
if you enable maximum VLAN mode.
Syntax
sys max-vlan-resource-reservation
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
max-vlan-resource-reservation Enables maximum VLAN mode.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys mgmt-virtual-ip
sys mgmt-virtual-ip
Create a virtual management port in addition to the physical management ports on the switch management modules.
Syntax
sys mgmt-virtual-ip <ipaddr/mask>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
mgmt-virtual- Configures the management virtual ip address to provide access to switch
ip
<A.B.C.D/X> management modules. <A.B.C.D/x> specifies the ip address and the subnet mask.
<ipaddr> Specifies the IP address and subnet mask of the management port (For example,
<mask> 10.127.231.15 255.255.255.0).
mgmt-virtual-
ip Specifies the management virtual IP address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys msg-control
sys msg-control
Configure system message control to suppress duplicate error messages on the console, and to determine the action to take if
they occur.
Syntax
sys msg-control action <suppress-msg|send-trap|both>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<cr> Activates system message control. Enabling this command suppresses
duplicate error messages.
action
<suppress- Configures the message control action.
msg|send-
trap|both>
control-interval Configures the message control interval in minutes. The valid options are 1 to
<1-30> 30.
Configures the number of occurrences of a message after which the control
max-msg-num <2-
500> action happens. To set the maximum number of occurrences, enter a value
from 2 to 500.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys msg-control action
Syntax
sys msg-control action <suppress-msg|send-trap|both>
Default
The default value is suppress-msg.
Command mode
Global configuration mode
Command parameters
Parameter Description
action Configures the message control action. To set this option to the default value, use the
<action default operator with the command. <action type> specifies the type of message control
type> action as one of the following:suppress-msg send-trap both
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys msg-control control-
interval
Syntax
sys msg-control control-interval
Default
The default value is 5.
Command mode
Global configuration mode
Command parameters
Parameter Description
control- Configures the message control interval in minutes. The valid options are 130. To
interval
<1-30> set this option to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys msg-control max-msg-
num
Syntax
sys msg-control max-msg-num <2-500>
Default
The default is 5.
Command mode
Global configuration mode
Command parameters
Parameter Description
max-msg- Configures the number of occurrences of a message after which the control action
num <2- happens. To set the maximum number of occurrences, enter a value from 2500. To set
500> this option to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys mtu
sys mtu
Enable support for Jumbo frames on Ethernet Routing Switch 8800/8600. NOTE: After changing the MTU size, you must reboot
the switch for the change to take effect.
Syntax
sys mtu <bytes>
Default
The default value is 1950.
Command mode
Global configuration mode
Command parameters
Parameter Description
Activates Jumbo frame support. bytes is the Ethernet frame size, either 1522, 1950
mtu
<bytes> (default), or 9600 bytes. To set this option to the default value, use the default operator
with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys multicast-resource-
reservation
sys multicast-resource-reservation
Reserve MGIDs for IPMC to increase the number of IPMC traffic streams supported on the system.
Syntax
sys multicast-resource-reservation <value>
Default
The default value is 2048.
Command mode
Global configuration mode
Command parameters
Parameter Description
value Specifies the number of MGIDs to reserve for IPMC traffic. Select from the range of 64
4083. To set this option to the default value, use the default operator with the command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys name
sys name
Change the system name to configure global options for the Ethernet Routing Switch 8800/8600.
Syntax
sys name WORD <0-255>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
name WORD Configures the system or root level prompt name for the switch. WORD <0-255> is an
<0-255> ASCII string from 0255 characters (for example, LabSC7 or Closet4).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys-name
sys-name
Specify a name for the system.
Syntax
[no] [default] sys-name <sys-name>
Default
The default the system name comes from the host name configured at the system level.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
Use the no option to set this parameter to the default value (host name). This may be
no used as the host name for dynamic host name exchange in accordance with RFC 2763.
By default, the system name comes from the host name configured at the system level.
Use the default option to set this parameter to the default value (host name). This may
default be used as the host name for dynamic host name exchange in accordance with RFC
2763. By default, the system name comes from the host name configured at the system
level.
<sys-
name> Specifies a name for the system.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys power
sys power
Enable power redundancy to create traps and events after power consumption exceeds redundancy capacity.
Syntax
sys power fan-check
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
fan-check Enables fan check to check the power management on the port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:sys record-reservation
sys record-reservation
Configure record reservation parameters to record the reservation and usage information for each record type.
Syntax
sys record-reservation filter <1025-8192>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
filter <1025- Configures information for filter record type. The filter value ranges from 1 025
8192> to 8 192.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:system-id
system-id
Specify the IS-IS system ID for the switch.
Syntax
[no] [default] system-id <system-id>
Default
The default is the node BMAC.
Command mode
IS-IS configuration mode
Command parameters
Parameter Description
no Use the no option to set this parameter to the default value (node BMAC).
default Use the default option to set this parameter to the default value (node BMAC).
<system-id> Specifies the IS-IS system ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:tacacs enable
tacacs enable
Enable Terminal Access Controller Access Control System plus (TACACS+) authentication to provide centralized validation of users
attempting to gain access to a router or network access server.
Syntax
tacacs enable
Default
None
Command mode
Global configuration mode
tacacs server
Configure a TACACS+ server to create the server and specify the authentication process.
Syntax
tacacs server<A.B.C.D>key <WORD 1-128>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<A.B.C.D> Specifies the IP address of the server you want to add. The no form of this command is
no tacacs server. The default form of this command is no tacacs server <A.B.C.D>.
Specifies the authentication and encryption key for all TACACS+ communications
between the device and the TACACS+ server. This key must match the encryption used
key on the TACACS+ daemon. The string length is 1128 characters. Important The key
<WORD 1 <value> parameter is a required parameter only when adding a new server entry. The
128> parameter is optional when modifying an existing entry. The no form of this command is
no tacacs server <A.B.C.D> key. The default form of this command is default tacacs
server <A.B.C.D> key.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:tcp-udp-base-port
tcp-udp-base-port
Specifies the TCP and UDP base port number. The range of values is from 49152..64983.
Syntax
tcp-udp-base-port <49152-64983>
Default
61000
Command mode
WLAN Switch Configuration
Command parameters
Parameter Description
<49152- Specifies the TCP and UDP base port number. The range of values is from
64983> 49152..64983.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:telnet-access login-timeout
telnet-access login-timeout
Configure the Telnet login timeout to define the generic configuration settings for ACLI sessions.
Syntax
telnet-access login-timeout <seconds>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
telnet-access Configures the time, in seconds, to wait for a Telnet logon before
login-timeout terminating the connection. The allowable range is from 3065535
<seconds> seconds.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:telnet-access sessions
telnet-access sessions
Configure the number of supported Telnet sessions to define the generic configuration settings for ACLI sessions.
Syntax
telnet-access sessions <nsessions>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
telnet-access Configures the allowable number of inbound Telnet sessions; the default
sessions <nsessions> is 8. nsessions is the number of sessions (08).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:terminal more disable
Syntax
terminal more disable
Default
None
Command mode
Privileged EXEC mode
test artable
Test the Address Resolution Protocol address table for consistency.
Syntax
test artable
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
stop artable Stop the test after a few seconds.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:test fabric
test fabric
Test the switch fabric for consistency. The fabric test causes the CPU to generate traffic and send it through the switch fabric.
Syntax
test fabric
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
stop fabric Stops the test after a few seconds.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:test hardware
test hardware
Test Packet-over-SONET input/output modules to ensure that they work properly.
Syntax
test hardware [<portList>]
Default
None
Command mode
Privileged EXEC mode
test led
Test the POS module LEDs to ensure that they are working properly.
Syntax
test led <portList> <tx|rx> <off|yellow|green
Default
None
Command mode
Privileged EXEC mode
test portList
Set the port to test mode to ensure continuity of the data path.
Syntax
test [<portList>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
portlist Specifies the port number to perform the test.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:trace auto enable
Syntax
trace auto enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables automatic trace feature.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:trace auto module
Syntax
trace auto module add <0-110> <0-4>
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
module Configures the trace autoenable function by specifying the module ID and level.<0-110>
add <0- specifies the module ID from 0 to 110. <0-4> specifies the trace level from 0 to 4, where
110> <0-
4> 0 is disabled; 1 is very terse; 2 is terse; 3 is very verbose, 4 is verbose.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:trace ethernet destination-
mac
Syntax
trace ethernet destination-mac <mac>
Default
01.02.03.04.05.06
Command mode
All modes
Command parameters
Parameter Description
<mac> 6-byte MAC address in xx.xx.xx.xx.xx.xx format
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:trace ethernet disable
Syntax
trace ethernet disable
Default
disable
Command mode
All modes
Syntax
trace ethernet enable
Default
disable
Command mode
All modes
Syntax
trace ethernet port <port> [vlan <value>]
Default
In the Master CP, no ports are assigned by default. In the Standby CP, the management port is
the default port.
Command mode
All modes
Syntax
trace flags isis [set <value>] [remove <value>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
Sets the IS-IS trace flags for the specified option: none tx-hello rx-hello tx-pkt rx-pkt adj
opt tx-lsack rx-lsack tx-lsp rx-lsp pkt-err nbr-mismatch flood spf-intra spf-inter spf-extern
[set
<value>] prefix nbr-change intf-change decide fdb dr dd-masterslave auth-fail config purge policy
redist tx-snp rx-snp timer spbm-decide global perf ha ucast-fib node mcast-fib isid ip-
shortcut
[remove Removes the IS-IS trace flags for the specified option. See the [set <value>] parameters
<value] for a list of options.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:trace ipv6
trace ipv6
Enable or disable trace for IPv6.
Syntax
trace ipv6 {base <enable|disable> | forwarding <enable|disable> | nd <enable|disable> |
ospf <enable|disable> | rtm <enable|disable> | transport <enable|disable>}
Default
disable
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
base <enable|disable> Enables or disables trace for IPv6 base.
forwarding <enable|disable> Enables or disables trace for IPv6 forwarding.
nd <enable|disable> Enables or disables trace for IPv6 nd.
ospf <enable|disable> Enables or disables trace for IPv6 OSPF.
rtm <enable|disable> Enables or disables trace for IPv6 rtm.
transport <enable|disable> Enables or disables trace for IPv6 transport.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:trace level
trace level
Use trace to observe the status of a software module at a given time.
Syntax
trace level [<0-110>] [<0-4>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
level Starts the trace by specifying the module ID and level.<0-110> specifies the module ID
[<0- from 0 to 110. <0-4> specifies the trace level from 0 to 4, where 0 is disabled; 1 is very
110>]
[<0-4>] terse; 2 is terse; 3 is very verbose, 4 is verbose.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:traceroute
traceroute
Use traceroute to determine the route packets take through a network to a destination.
Syntax
traceroute <IP address> vrf <value>
traceroute <A.B.C.D> [<1-1464>] [-m <1-255>] [-p <0-65535>] [-q <1-255>] [-w <1-255>] [-v]
[source <WORD 1-256>] [vrf <WORD 0-16>]
Default
None
Command mode
Privileged EXEC mode
Command parameters
Parameter Description
-m <1-255> Specifies the is maximum time-to-live (TTL) (1 to 255).
-p <0-65535 Specifies the base UDP port number (0 to 65535).
-q <1-255> Specifies the number of probes per TTL (1 to 255).
-v Specifies verbose mode (detailed output).
-w <1-255> Specifies the wait time per probe (1 to 255).
<1-1464> Specifies the size of the probe packet (1 to 1464).
source <WORD 1-256> Specifies the source IP address for use in IP VPN traceroutes.
vrf <WORD 0-16> Specifies the VRF instance by VRF name.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:trace screen
trace screen
Enable or disable the show trace screen.
Syntax
trace screen {enable|disable}
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the show trace screen.
disable Disables the show trace screen.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:trace syslog destination
Syntax
trace syslog destination
Default
None
Command mode
All modes
Command parameters
Parameter Description
<ipaddr> Specifies the IP address in the {a.b.c.d} format.
[next-hop-mac Specifies the MAC address of the next hop towards the specified
<value>] destination.
[port <value>] Specifies the port number in the slot/port format.
[vlan <value>] Identifes the VLAN to which the port belonngs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:trace syslog disable
Syntax
trace syslog disable
Default
disable
Command mode
All modes
Syntax
trace syslog enable
Default
disable
Command mode
All modes
traps
Enable BGP traps.
Syntax
traps enable
Default
The default value is disable.
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables BGP traps.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:tx-flow-control enable
tx-flow-control enable
Enable TX flow control to allow the TX to transmit the MAC control PAUSE frames to indicate congestion on the receive side of the
port interface. Flow control can only be enabled on 1 Gbit/s and 10 Gbit/s ports. Flow control cannot be enabled for ports that run
at less than 1 Gbit/s.
Syntax
tx-flow-control enable
Default
The default is disable.
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the TX flow control on the module.
port [portlist] Specifies the slot and the port number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:udp checksum
udp checksum
Enables the udp checksum calculation on the Ethernet Routing Switch 8800/8600.
Syntax
udp checksum
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
checksum Enables the udp checksum calculation on the Ethernet Routing Switch 8800/8600.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:udpsrc-by-vip
udpsrc-by-vip
Enable virtual ip as the udp source on the Ethernet Routing Switch 8800/8600.
Syntax
udpsrc-by-vip
Default
None
Command mode
Global configuration mode
untagged-frames-discard enable
Configure the untagging default VLAN on a tagged port to separate untagged packets originating from a PC from the tagged
packets originating from an IP phone.
Syntax
untagged-frames-discard enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
ports Specifies the ports which are to be changed.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vendorname nasIPaddress
type version.log
Syntax
vendorname_nasIPaddress_type_version.log
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
vendorname A two-character symbol representing the vendor. nr represents a specific Avayal
project.
Identifies the network access server (NAS) by its IP address.Important When there
are less than three digits in an octet such as 10 and 1, leading zeroes fill in to make
nasIPaddress up the 12 digits. If the Ethernet Routing Switch 8800/8600 cannot determine the
NAS IP address, create a file corresponding to NAS IP address 0.0.0.0 such as: 7672
MAR-17-2003 11:42:20 /pcmcia/ nr_000000000000_rac_01.log.
type Uses three characters to represent the kind of log.
version Uses two digits to represent the version number.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlacp
vlacp
Configure VLACP on a port to ensure there is end-to-end reachability.
Syntax
vlacp
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables VLACP for this port.
ethertype <1-65535> Sets the VLACP protocol identification for this port.
fast-periodic-time <10-20000> Sets the fast periodic time (in milliseconds) for this port.
Sets the multicast MAC address used for the VLACPDU.
funcmac-addr
<<0x00:0x00:0x00:0x00:0x00:0x00>> Specify a MAC address in the format
0x00:0x00:0x00:0x00:0x00:0x00.
slow-periodic-time <10000-30000> Sets the slow periodic time (in milliseconds) for a specific
port type.
Sets the port to use the long or short timeout: long sets
the port to use the timeout-scale value multiplied by the
slow-periodic-time. short sets the port to use the
timeout-scale value multiplied by the fast-periodic-time.
timeout {long|short} For example, if you specify a short timeout, set the
timeout-scale value to 3, and the fast-periodic-time to
400 ms, the timer will expire within 1000 to 1200 ms. To
set this option to the default value, use the default
operator with the command.
Sets a timeout scale for this port used to calculate the
timeout-scale <2-10> timeout. The default value is 3. To set this option to the
default value, use the default operator with the
command.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlacp enable
vlacp enable
Enable or disable the VLACP globally to reset all port level settings on the chassis.
Syntax
vlacp enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the VLACP globallly.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan action
vlan action
Perform the general VLAN operations to set a Quality of Service (QoS) level for the VLAN add and to change the name of a VLAN.
Syntax
vlan action <1-4094> {none|flushMacFdb|flushArp|flushIp|flushDynMemb|triggerRipUpdate|all}
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
none Sets action to none.
flushArp Sets action to flushMacFdb.
flushIp Sets action to flushIp.
flushDynMemb Sets action to flushDynMemb.
triggerRipUpdate Sets action to triggerRipUpdate.
all Sets action to all.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan create
vlan create
Configure a VLAN before you can configure it as an IPv6 VLAN.
Syntax
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
name
<value> Configures a name for the VLAN.
Specifies the type of VLAN to create. The options are:port [<stgId:1-16>|cist|msti <1-15>] protocol-ApltkEther2Snap protocol-decEther2 protocol-
decOtherEther2 protocol-ipEther2 protocol-ipv6Ether2 protocol-ipx802.2 protocol-ipx802.3 protocol-ipxEther2 protocol-ipxSnap protocol-Netbios
protocol-RarpEther2 protocol-sna802.2 protocol-snaEther2 protocol-Userdef <4096-65534> protocol-vinesEther2 protocol-xnsEther2 ipsubnet-
mstprstp <1-63> <A.B.C.D/0-32> [color<1-32>] port-mstprstp <1-63> <A.B.C.D/0-32> [color<1-32>] [naap-vlan] protocol-mstprstp <1-63>
type ip|ipx802dot3|ipx802dot2|ipxSnap|ipxEthernet2|appleTalk|decLat|decOther|sna802dot2|snaEthernet2|netBios|xns|vines|ipV6|usrDefined|rarp|PPPoE
<value> [<pid>] [color <1-32>] [encap <value>] srcmac-mstprstp <1-63> [color <1-32>] svlan-mstprstp <1-63> [color <1-32>] ids-mstprstp <1-63>
[color <1-32>] ipsubnet <1-63> <A.B.C.D/mask> [color <1-32>] srcmac <1-63> [color <1-32>] svlan <1-63> [color <1-32>] ids <1-63>
[color <1-32>] stgId is the spanning tree group ID. color <value> is the color of the VLAN. The color attribute is used by Optivity software to
display the VLAN. pid is a user-defined protocol ID number in hexadecimal format (065535). encap <value> is the frame encapsulation method.
Important The mstprstp options are available for the Avaya Ethernet Routing Switch 8800/8600 only.
vid Specifies the VLAN ID (from 14094).
<1-4094> Specifies the VLAN ID in the range of 1 to 4094.
color 0- Specifies the color of the VLAN.
32
IDS <1-
64> Creates a VLAN by IDS. <1-64> is the Spanning Tree ID.
<WORD 0- Specifies the VLAN name.
64>
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan create type spbm-bvlan
Syntax
[no] vlan create <vlan-id> type spbm-vlan
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
[no] Use the no option to delete the specified SPBM VLAN.
<vlan-id> Specifies the VLAN ID.
name <value> Specifies the name of the VLAN {string length 0..64}
color <value> Specifies the color of the VLAN{0..32}
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan create type svlan
Syntax
vlan create <1-4094> [name<WORD 0-64> type svlan <1-64> [color <WORD 0-32>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
svlan
<sid> Creates an sVLAN. sid is spanning tree ID. name <value> is the name of the VLAN
[name from 0 to 64 characters. color <value> is the color of the VLAN (0 to 32). The color
<value>] attribute is used by Optivity software to display the VLAN. This command is available
[color only for the Avaya Ethernet Routing Switch 8800/8600.
<value>]
<1-4094> Specifies the VLAN ID. VLAN 1 is the default VLAN ID.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan create type svlan-
mstprstp
Syntax
vlan create <1-4094> [name<WORD 0-64> type svlan-mstprstp <1-64> [color <WORD 0-32>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
svlan-mstprstp Creates an sVLAN. instance-id is the instance ID from 0 to 63. name <value> is
<0-64> [name the name of the sVLAN in the range 0 to 20. color <value> is the color of the
<value>] [color sVLAN in the range of 0 to 32. The color attribute is used by Optivity software
<value>] to display the VLAN.
<1-4094> Specifies the VLAN id. VLAN 1 is the default VLAN.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan i-sid
vlan i-sid
Specify the customer VLAN (CVLAN) to associate with the I-SID.
Syntax
[no] [default] vlan i-sid <vlan-id> <isid>
Default
The default is disabled.
Command mode
Global configuration mode
Command parameters
Parameter Description
no Use the no option to remove the I-SID from the specified VLAN.
default Use the default option to remove the I-SID from the specified VLAN.
<vlan-id> Specifies the VLAN ID.
<isid> Indicates the IS-IS SPBM I-SID identifier.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan mac-address-entry
vlan mac-address-entry
Configure the entries in the FDB to configure or modify the VLAN entries in the FDB.
Syntax
vlan mac-address-entry <1-4094> address <H.H.H> status {other|invalid|learned|self|mgmt}
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
address <H.H.H> status
{other|invalid|learned|self|mgmt} Sets the FDB monitor.
aging-time <10-1000000> Sets the FDB aging timer. seconds indicates the timeout
period in seconds.
flush Flushes the FDB.
Sets a QoS level for a VLAN: mac indicates the MAC
address. status <value> is the forwarding database
qos-level <mac> status <value>
<0-7> status according to one of the following choices:
{other|invalid|learned|self|mgmt}. 0-7 sets the QoS
level. QoS level 7 is reserved for network control traffic.
sync Synchronizes the switch forwarding database with the
forwarding database of the other aggregation switch.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan mac-address-entry
status
Syntax
vlan mac-address-entry <1-4094> qos-level <H.H.H> <0-6> status
<other|invalid|learned|self|mgmt>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Specifies the QoS level. The default is 1. To use the
<0-6> default configuration, use the default option in the
command.
<1-4094> Specifies the VLAN ID.
<H.H.H> Specifies the MAC address in the format
0x00:0x00:0x00:0x00:0x00:0x00
<portList> Specifies the slot and port, or slot and port list.
status Specifies the FDB status (other|invalid|learned|
<other|invalid|learned|self|mgmt> self|mgmt).
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan mac-address-filter
vlan mac-address-filter
Configure the VLAN filter members to set VLAN filter members.
Syntax
vlan mac-address-filter <1-4094> <H.H.H> <portList> <0-6>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<0-6> Specifies the QoS level. The default is 1. To use the default
configuration, use the default option in the command.
<1-4094> Specifies the VLAN ID.
<H.H.H> Specifies the MAC address in the format
0x00:0x00:0x00:0x00:0x00:0x00
<portList> Specifies the slot and port, or slot and port list.
<0x00:0x00:0x00:0x00:0x00:0x00> Specifies the MAC address in the format
0x00:0x00:0x00:0x00:0x00:0x00.
<1-4094> Specifies the VLAN by VLAN ID.
Adds a filter member to a VLAN bridge: mac indicates the
<mac> port <value> qos <value> MAC address. port <value> indicates the port (slot/port)
number. qos <value> is the QoS level. QoS level 7 is
reserved for network control traffic.
no Disables VLAN filter member when prefixed with the
command.
notallowfrom Adds a not allowed filter member to a VLAN.
pcap <H.H.H> [enable] Enables or disables the Packet Capture (PCAP)Tool. mac
indicates the MAC address.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan mac-address-filter
notallowfrom
Syntax
vlan mac-address-filter <1-4094> notallowfrom <H.H.H> <portList> [<srcOnly|dstOnly|Both>]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
Adds a not-allowed filter member to a VLAN bridge: mac indicates
<mac> <value>
[<srcOnly|dstOnly|Both>] the MAC address. value indicates the port (slot/port) number.
srcOnly|dstOnly|Both is an optional command to set a mask.
<1-4094> Specifies the VLAN id in the range of 1 to 4094.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan mac-address-static
vlan mac-address-static
Configure Layer 2 multicast MAC filtering to direct MAC multicast flooding to a specific set of ports.
Syntax
vlan mac-address-static <1-4094> <MAC address> <ports> qos <0-7>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
MAC
address Specifies the MAC address in hexadecimal format.
<ports> Specifies the port or ports that receive the multicast flooding. Type this information as
a port or a range of ports in slot/port format.
qos <0-7> Specifies the Quality of Service level.
14094 Specifies a VLAN from 14094.
<0-6> Specifies the QoS level. The default is 1. To use the default configuration, use the
default option in the command.
<1-4094> Specifies the VLAN ID.
<H.H.H> Specifies the MAC address in the format 0x00:0x00:0x00:0x00:0x00:0x00
<portList> Specifies the slot and port, or slot and port list.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan-map
vlan-map
Specifies the L3 mobility mode for the VLAN map.
Syntax
vlan-map {l3-mobility [none|server|client]}
Default
None
Command mode
WLAN Switch Configuration
Command parameters
Parameter Description
<name:WORD Specifies a unique name for this mobility VLAN map. The name can be up to 32
032> characters.
Specifies the L3 mobility mode for the VLAN map. none - means that L3 mobility
l3-mobility is not enabled for this VLAN, but L2 mobility is enabled. server - means that L3
[none|server] mobility is enabled for this VLAN, and this switch can act as a server for this
mobility VLAN.
[lvid <1-
4094>] Specifies the local VLAN ID number for this map.
Specifies a weight value to prioritize switches when there are a number of them
[weight <1-
7>] configured as the server for this VLAN. The switch with the lowest number is the
winning server.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan-map lvid
vlan-map lvid
Specifies the local VLAN ID number for this map.
Syntax
vlan-map [lvid <1-4094>]
Default
None
Command mode
WLAN Switch Configuration
vlan-map name
Specifies a unique name for this mobility VLAN map. The name can be up to 32 characters.
Syntax
vlan-map <name:WORD 0-32>
Default
None
Command mode
WLAN Switch Configuration
vlan-map weight
Specifies a weight value to prioritize switches when there are a number of them configured as the server for this VLAN. The switch
with the lowest number is the winning server.
Syntax
vlan-map [weight <1-7>]
Default
1
Command mode
WLAN Switch Configuration
vlan members
Add or remove the ports in a VLAN to configure the ports in the VLAN.
Syntax
vlan members <1-4094> <portList> [{portmember|static|notallowed}]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
portmember Select the port type to port member.
static Selects the port type to static.
notallowed Selects the port type to not-allowed.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan nodal-mep
vlan nodal-mep
Add nodal MEPs to the VLAN.
Syntax
vlan nodal-mep <vid> <md-name> <ma-name> <mepID>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<vid> Specifies the VLAN ID.
<md-name> Specifies the MD name in a string of 122 characters.
<ma-name> Specifies the MA name in a string of 122 characters.
<mepID> Specifies the nodal MEPs to add to the VLAN. Range is 18191.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan nodal-mip-level
vlan nodal-mip-level
Add a nodal MIP level to the VLAN.
Syntax
vlan nodal-mip-level {<level>[,<level>][,...]}
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
{<level>[,<level>][,...]} Specifies a MIP level list, within the range of 0-7.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan-reservation
vlan-reservation
Adds a list of VLANs to the reserved pool. Use the no vlan-reservation <vidList> command to remove a list of VLANs.
Syntax
vlan-reservation <vidList>
Default
None
Command mode
WLAN Switch Configuration
Command parameters
Parameter Description
<vidList> Adds a list of VLANs to the reserved pool. Use the no vlan-reservation <vidList>
command to remove a list of VLANs.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vlan srcmac
vlan srcmac
Add or remove a VLAN source MAC addresses to configure the source MAC address to a VLAN.
Syntax
vlan srcmac <1-4094> <H.H.H>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
srcmac Specifies the source MAC address.
<1-4094> Specifies the VLAN ID in the range of 1to4094.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vrf
vrf
Assign an interface to the VRF to enable data path traffic between the PE node and the CE node.
Syntax
vrf <WORD 0-16>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
<WORD 0-16> Specifies the name of the VRF instance to associate with the VLAN or port.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:vrf word 0-16
Syntax
vrf <WORD 0-16>
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
vrf <WORD 0-16> <WORD 0-32> specifies the VRF name.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:wan-mode
wan-mode
Configure the Wide Area Network (WAN) mode for LAN or WAN or both modules.
Syntax
wan-mode enable
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
enable Enables the WAN mode on the module.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
Command:web-server enable
web-server enable
Configure the Web management interface to provide management access to the switch using a Web browser.
Syntax
web-server [def-display-rows] [enable] [help-tftp] [http-port] [password] [secure-only]
Default
None
Command mode
Global configuration mode
Command parameters
Parameter Description
def-display-rows Sets Web server default display row width.
enable Enables the Web interface.
help-tftp Sets Web server HTML directories.
http-port Sets Web server HTTP port.
password Sets Web server password.
secure-only Enables secure-only on Web interface.
ERS 8600/8800 Release 7.2
NN46205-106 Avaya Command Line Interface Commands Reference
Version 01.02 October 11 2012
Avaya Inc. 2012 All Rights Reserved.
Avaya.com/support
All modes
All modes
| E | T | Back to top
E
end
exit
| E | T | Back to top
T
trace ethernet destination-mac
trace ethernet disable
trace ethernet enable
trace ethernet port
trace syslog destination
trace syslog disable
trace syslog enable
R
redistribute isis
redistribute isis enable
redistribute isis metric
redistribute isis route-map
Configuration Mode
| S | Back to top
S
show ip interface
C
cp-limit port multicast-limit
R
routing
A
accept adv-rtr
accept adv-rtr enable
access-diffserve
access-policy
access-policy access-restrict
access-policy by-mac
access-policy enable
access-policy ftp
access-policy host
access-policy mode network precedence
access-policy name
access-policy snmp-group
action flushIp
action triggerRipUpdate
aggregate-address as-set
area import
area range
area virtual-link
area virtual-link message-digest-key
auto-negotiate enable
auto-negotiation-advertisements
auto-peer-restart enable
auto-recover-port port enable
auto-summary
auto-vlink
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
B
bandwidth-limit
banner
bgp
boot
boot config
boot config bootp
boot config bootp primary
boot config choice
boot config choice primary image-file
boot config cli
boot config delay
boot config flags
boot config flags 8616-reautoneg
boot config flags access-service
boot config flags block-snmp
boot config flags factorydefaults
boot config flags ftpd
boot config flags ha-cpu
boot config flags spanning-tree-mode
boot config flags sshd
boot config host
boot config master
boot config mezz-image
boot config mezz-image image-name
boot config net
boot config net mgmt ip
boot config net mgmt route
boot config sio modem
boot config tz
brouter port
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
C
cfm ethertype
cfm maintenance-association
cfm maintenance-domain
cfm maintenance-endpoint
clear khi all
clear khi chassis
clear khi forwarding
clear khi ip
clear khi log
clear khi performance
clear khi port
clear khi protocol
clilog
clilog enable
cli password
clock source
clock sync-time
comp-bestpath-med-confed
copy srcfile destfile
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
D
debug ip pim
debug-screen
default-information
default ip
default-metric (BGP)
default-metric (RIP)
dos-format
dsapssap
dump ercd record
dump rsp-trace egress-display-pkt
dump rsp-trace ingress-pkt-trace
duplex
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
E
eapol enable
eapol port
eapol sess-manage enable
eapol status
eapol status auto
eapol status unauthorized
enable-diffserve
encapsulation dot1q
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
F
filter acl
filter acl ace
filter acl ace action
filter acl ace advanced
filter acl ace arp
filter acl ace debug
filter acl ace ethernet
filter acl ace ip
filter acl ace ipv6
filter acl ace protocol
filter acl enable
filter acl port
filter acl set
filter acl set default-action
filter acl vlan
filter act
filter act name
filter act pattern
filter apply act
flap-dampening
flow-control
fpga update
fpga update bmc
fpga update dpc
fpga update pim
fpga update rs-module-dpm
fpga update rs pim
framing sonet
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
G
global-debug
global-debug mask
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
H
high-secure enable
host-route
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
I
ibgp-report-import-rt
ignore-illegal-rtrid
ip access-list extended
ip address
ip alternative-route
ip arp
ip arp inspection vlan
ip arp-proxy enable
ip arp-response
ip arp static-mcast
ip as-list
ip bfd brouter port
ip bfd vlan enable
ip bgp enable
ip bgp in-route-policy
ip bgp multiple-paths
ip bgp neighbor
ip bgp neighbor allow-as-in
ip bgp neighbor as-override
ip bgp neighbor remove-private-as
ip bgp neighbor site-of-origin
ip community-list
ip dhcp-relay
ip dhcp-relay broadcast
ip dhcp-relay fwd-path
ip dhcp-relay fwd-path enable
ip dhcp-relay fwd-path mode
ip dhcp snooping binding interface
ip dhcp snooping enable
ip dhcp snooping vlan enable
ip directed-broadcast enable
ip domain-name
ip dvmrp
ip dvmrp active
ip dvmrp advertise-self port
ip dvmrp advertise-self vlan
ip dvmrp default-listen ethernet port
ip dvmrp default-listen vlan
ip dvmrp enable ethernet port
ip dvmrp enable vlan
ip dvmrp in-policy ethernet port
ip dvmrp in-policy vlan
ip dvmrp interface-type active
ip dvmrp out-policy
ip dvmrp show-next-hop-table
ip ecmp
ip ecmp max-path
ip extcommunity-list
ip forward-protocol udp
ip forward-protocol udp broadcastmask
ip forward-protocol udp maxttl
ip forward-protocol udp portfwd
ip forward-protocol udp portfwdlist
ip icmp redirect
ip igmp access-list ethernet port
ip igmp access-list mode
ip igmp access-list mode vlan
ip igmp access-list vlan
ip igmp ethernet port
ip igmp generate-log
ip igmp igap
ip igmp immediate-leave
ip igmp immediate-leave-members
ip igmp immediate-leave-mode
ip igmp mrdisc
ip igmp ssm group-range
ip igmp ssm-map
ip igmp static-group
ip igmp stream-limit
ip igmp stream-limit-group
ip igmp stream-limit-max-streams
ip igmp stream-limit vlan
ip igmp version
ip ipfix collector
ip ipfix enable
ip ipfix port
ip ipfix slot
ip irdp
ip irdp address
ip mroute interface
ip mroute resource-usage egress-threshold
ip mroute resource-usage log-msg trap-msg
ip mroute static-source-group
ip mroute stream-limit
ip mroute stream-limit interface
ip msdp connect-retry
ip msdp default-peer
ip msdp description
ip msdp enable
ip msdp implicit-default-peer
ip msdp keepalive
ip msdp md5-authentication
ip msdp mesh-group
ip msdp originator-id
ip msdp password peer
ip msdp peer
ip msdp redistribute
ip msdp sa-filter
ip msdp sa-limit
ip msdp ttl-threshold
ip name-server primary
ip ospf
ip ospf apply redistribute
ip ospf area
ip ospf bfd
ip ospf enable
ip ospf redistribute
ip ospf redistribute bgp
ip ospf redistribute bgp enable
ip pgm enable
ip pgm enable vlan
ip pim bsr-candidate preference value ethernet port
ip pim bsr-candidate preference value vlan
ip pim enable
ip pim enable ethernet port
ip pim enable vlan
ip pim enable vrf
ip pim mbr
ip pim mode sparse
ip pim mode ssm
ip pim static-rp
ip pim virtual-neighbor
ip prefix-list
ip redistribute enable
ip rip
ip rip apply redistribute
ip rip out-policy
ip rip redistribute
ip rip redistribute bgp enable
ip route
ip route bfd
ip route default
ip route preference
ip route preference protocol spbm-level1
ip routing
ip rsmlt
ip rsmlt edge-support
ip rvs-path-chk mode port
ip rvs-path-chk mode vlan
ip static-mroute
ip ttl
ipv6 area
ipv6 area range
ipv6 area virtual-link
ipv6 as-boundary-router enable
ipv6 dhcp-relay fwd-path
ipv6 icmp error-interval
ipv6 interface address
ipv6 interface address vlan
ipv6 interface multicast-routing
ipv6 interface multicast-routing brouter
ipv6 mgmt-virtual
ipv6 mld
ipv6 mld brouter
ipv6 multicast-routing
ipv6 nd
ipv6 nd prefix
ipv6 nd prefix-interface
ipv6 neighbor
ipv6 ospf area
ipv6 ospf area vlan
ipv6 ospf enable
ipv6 ospf enable vlan
ipv6 ospf nbma-nbr
ipv6 ospf nbma-nbr vlan
ipv6 redistribute direct
ipv6 route
ipv6 tunnel
ipv6 tunnel vlan
ipvpn
ipvpn enable
ipvpn service-label-allocation
ip vrrp
isis apply redistribute vrf
isis hello-auth type
isis l1-dr-priority
isis l1-hello-interval
isis l1-hello-multiplier
ist enable
ist peer-ip
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
K
khi boot-delay
khi chassis
khi enable
khi performance
khi port
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
L
lacp
lacp enable
lacp enable key
link-flap-detect auto-port-down
link-flap-detect frequency
link-flap-detect interval
link-flap-detect send-trap
linktrace
load-encryption-module
load-license
lock port
logging
logging logToPCMCIA
logging transferfile
login-message
loopback
loop-detect action
loop-detect arp-detect
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
M
mac-security auto-learning
match extended-prefix
max-logins
mirror-by-port
mlt
mlt member
mpls ldp ethernet
mpls ldp globally
mpls ldp vlan
mpls router-id
mpls rsvp ethernet
mpls rsvp explicit-path
mpls rsvp globally
mpls rsvp lsp
mpls rsvp lsp primary
mpls rsvp resource
mpls rsvp static-ip
mpls rsvp vlan
mpls statistics receive
mpls statistics receive start-label
multicast mlt-distribution enable
multicast mlt-distribution globally
multicast mlt-distribution multilink trunk
multicast smlt-square
multicast software-forwarding
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
N
name port
neighbor
neighbor a.b.c.d fall-over bfd
neighbor address-family vpnv4
neighbor-debug-all
neighbor-debug-all mask
neighbor ipaddress
neighbor ipvpn-lite-capability
net6-mgmt ipv6
net6-mgmt ipv6 route
network
nlb-mode unicast
no access-diffserve enable
no access-policy
no boot config flags autoboot
no cfm maintenance-association
no cfm maintenance-domain
no cfm maintenance-endpoint
no cfm maintenance-endpoint enable
no ip msdp peer
no ip msdp redistribute route-policy
no ip route
no ipvpn
no ist enable
no ist peer-ip
no-med-path-is-worst
no mlt member
no pcap enable
no pcap enable globally
no qos 802.1p-override
no tacacs enable
no tacacs server
nsna enable
nsna nsnas
nsna phone-signature
nsna port
nsna uplink vlans
nsna vlan
ntp authentication-key
ntp interval
ntp server
ntp server auth-enable
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
P
password access-level
password aging-time
password aging-time
password default-lockout-time
password lockout
password min-passwd-len
password password-history
passwordprompt
pcap 1-1000
pcap capture-filter
pcap enable
pcap enable mode
pcap enable mode
pcap reset-stat
ping-snoop
pluggable-optical-module
portlock enable
port-phy portlist
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
Q
qos 802.1p-override
qos egressmap exp
qos egress-queue-set
qos egress-queue-set qmax
qos egress-queue-set queue
qos if-policer
qos if-shaper
qos ingressmap exp
qos level port
qos level vlan
qos policy
quick-start
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
R
radius
radius accounting
radius cli-cmd-count
radius cli-profile
radius command-access-attribute
radius enable
radius enable eapol
radius igap-timeout-log-fsize
radius mcast-addr-attr-value
radius server host
radius server host used-by igap
radius-snmp acct-enable
radius sourceip-flag
rd
redistribute
redistribute ospf
remote-mirroring
rip enable
rmon
route-map
route-map enable
route-map match
route-map match condition
route-map match extcommunity
route-map permit
route-map policy name seq number
route-map policyname seqnumber
route-map policy name seq number permit
router bfd enable
router bgp
router bgp enable
route-reflector enable
route-refresh
router-id
router isis
router isis enable
router ospf enable
router ospf ipv6-enable
router vrf
route-target both
route-target import
rsp-trace ingress-pkt-trace enable
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
S
save bootconfig
save config standby
sffd enable
show boot config
show boot config choice
show brouter
show cfm ethertype
show cfm maintenance-association
show cfm maintenance-domain
show cfm maintenance-endpoint
show filter acl ethernet
show filter acl ip
show ip arp
show ip as-list
show ip community-list
show ip directed-broadcast interface
show ip dns
show ip extcommunity-list
show ip forward-protocol udp
show ip forward-protocol udp portfwdlist
show ip igmp sys
show ip ipvpn
show ip ipvpn rd
show ip irdp
show ip irdp interface
show ip isis redistribute
show ip mroute interface
show ip pim
show ip rip
show ip route preference
show ip routing
show ip static-mroute
show isis spbm
show khi chassis
show khi forwarding
show khi info
show khi ip-interface
show khi mgmt
show khi performance
show khi port
show khi protocol-stats
show multicast software-forwarding
show nsna nsnas
show nsna phone-signature
show nsna vlan
show remote-mirroring
show route-map
show rsp-trace
show running-config mode acli
show spanning-tree rstp port config
show sys 8648gtr
show vlan basic
show vlan nodal-mep
show vlan nodal-mip-level
shutdown
slot reset
slpp enable
slpp ethertype
slpp port
slpp tx-interval
slpp vid
smlt
smlt port
snmplog
snmp-server
snmp-server
snmp-server community
snmp-server group
snmp-server host v1
snmp-server host v2
snmp-server host v3
snmp-server notify-filter
snmp-server sender-ip
snmp-server user
snmp-server user engine-id
snmp-server user group
snmp-server view
spanning-tree mstp msti
spanning-tree rstp version
spanning-tree stp
spanning-tree stp change-detection
spanning-tree stp create
spanning-tree stp trap-stp
spbm
spbm ethertype
speed
spoof-detect portlist enable
ssh
svlan
svlan-porttype
synchronization
sys 8648gtr high-priority-control-mac
sys action
sys action cpu-switch-over
sys ecn-compatibility
sys ext-cp-limit max-ports-to-check
sys ext-cp-limit min-congestion-time
sys ext-cp-limit port
sys ext-cp-limit port-congestion-time
sys ext-cp-limit trap-level
sys flags enhanced-operational-mode
sys flags global-filter-ordering
sys force-msg
sys global-filter
sys hash-calc getmltindex traffic-type
syslog enable
syslog host
sys max-vlan-resource-reservation
sys mgmt-virtual-ip
sys msg-control
sys msg-control action
sys msg-control control-interval
sys msg-control max-msg-num
sys mtu
sys multicast-resource-reservation
sys name
sys power
sys record-reservation
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
T
tacacs enable
tacacs server
telnet-access login-timeout
telnet-access sessions
test portList
trace auto enable
trace screen
traps
tx-flow-control enable
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
U
udp checksum
udpsrc-by-vip
untagged-frames-discard enable
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
V
vendorname nasIPaddress type version.log
vlacp
vlacp enable
vlan action
vlan create
vlan create type spbm-bvlan
vlan create type svlan
vlan create type svlan-mstprstp
vlan i-sid
vlan mac-address-entry
vlan mac-address-entry status
vlan mac-address-filter
vlan mac-address-filter notallowfrom
vlan mac-address-static
vlan members
vlan nodal-mep
vlan nodal-mip-level
vlan srcmac
vrf
vrf word 0-16
A | B | C | D | E | F | G | H | I | K | L | M | N | P | Q | R | S | T | U | V | W | Back to top
W
wan-mode
web-server enable
I
ip arp inspection
ip dhcp snooping
ipv6 dhcp-relay
ipv6 vrrp
ipv6 vrrp address
ip verify source interface
isis
isis enable
isis spbm
isis spbm interface-type
isis spbm l1-metric
| I | S | Back to top
S
show access-policy
show autotopology nnm-table
show ip arp inspection interface
show ipv6 vrrp
spb-multicast enable
C
csnp-interval
| C | I | M | O | P | R | S | Back to top
I
ip-source-address
is-type
| C | I | M | O | P | R | S | Back to top
M
max-lsp-gen-interval
metric
min-lsp-gen-interval
| C | I | M | O | P | R | S | Back to top
O
overload
overload-on-startup
| C | I | M | O | P | R | S | Back to top
P
psnp-interval
| C | I | M | O | P | R | S | Back to top
R
redistribute enable
retransmit-lsp-interval
| C | I | M | O | P | R | S | Back to top
S
spbm ip enable
spbm lsdb-trap enable
spf-delay
sys-name
system-id
I
isis apply redistribute
R
redistribute isis metric-type
redistribute isis route-policy
redistribute isis subnets
B
boot file config value
| B | C | D | F | I | L | M | P | Q | R | S | T | Back to top
C
clear filter
clear filter acl
clear ip arp interface
clear ip igmp igap-counters
clear ip ipfix
clear ip msdp peer
clear ip msdp sa-cache
clear ip msdp statistics
clear ip route interface
clear ip traffic-filter
clear ipv6 vrrp
clear isis lsdb
clear isis stats
clear radius statistics
clear wireless-switch mac-address-entry
clear wireless-switch statistics
clock set
copy
| B | C | D | F | I | L | M | P | Q | R | S | T | Back to top
D
debug spbm l2vpn action-call
debug spbm l2vpn event-notify
debug spbm l2vpn fib-update
debug spbm l2vpn fib-update-cvlan
dir
dump ar
| B | C | D | F | I | L | M | P | Q | R | S | T | Back to top
F
format-flash
| B | C | D | F | I | L | M | P | Q | R | S | T | Back to top
I
install
ip apply redistribute isis
ip [bgp|ospf|rip] apply redistribute
ip ospf apply accept
ip ospf apply accept adv-rtr
ip ospf spf-run
| B | C | D | F | I | L | M | P | Q | R | S | T | Back to top
L
l2 ping
l2 traceroute
l2 tracetree
| B | C | D | F | I | L | M | P | Q | R | S | T | Back to top
M
md5 filename
more boot.cfg
mpls statistics transmit
mpls statistics transmit start-label
| B | C | D | F | I | L | M | P | Q | R | S | T | Back to top
P
peer telnet
ping
ping hostname
ping-mpls ipv4
ping-mpls rsvp
| B | C | D | F | I | L | M | P | Q | R | S | T | Back to top
Q
qos apply egress-queue-set
| B | C | D | F | I | L | M | P | Q | R | S | T | Back to top
R
remove word
reset
| B | C | D | F | I | L | M | P | Q | R | S | T | Back to top
S
save config
save config file
save config file mode acli
save config file mode cli
save config mode
save trace
show banner
show basic config
show bgp ipv6 aggregates
show bgp ipv6 imported-routes
show bgp ipv6 neighbors
show bgp ipv6 networks
show bgp ipv6 redistributed-routes
show bgp ipv6 route
show boot config flags
show boot config master
show cli info
show clilog
show clilog file
show cli password
show clock
show eapol
show fdb-filter
show filter acl
show filter acl ace
show filter acl action
show filter acl advanced
show filter acl arp
show filter acl config
show filter acl debug
show filter acl ipv6
show filter acl protocol
show filter acl statistics port
show filter act
show filter act-pattern
show fulltech
show ha-state
show history
show hosts
show interfaces atm statistics
show interfaces atm statistics ds3fecurrent
show interfaces atm statistics ds3feinterval
show interfaces atm statistics ds3fetotal
show interfaces atm statistics ds3necurrent
show interfaces atm statistics ds3neinterval
show interfaces atm statistics ds3netotal
show interfaces atm statistics felinecurrent
show interfaces atm statistics felineinterval
show interfaces atm statistics fepathcurrent
show interfaces atm statistics fepathinterval
show interfaces atm statistics linecurrent
show interfaces atm statistics lineinterval
show interfaces atm statistics pathcurrent
show interfaces atm statistics pathinterval
show interfaces atm statistics sectioncurrent
show interfaces atm statistics sectioninterval
show interfaces atm statistics sonetmediumtbl
show interfaces dhcp-relay
show interfaces error ospf
show interfaces FastEthernet error
show interfaces FastEthernet statistics
show interfaces gigabitEthernet
show interfaces loopback
show interfaces statistics
show interfaces statistics dhcp-relay
show interfaces statistics egress-queues
show interfaces statistics ipvpn
show interfaces statistics lacp
show interfaces statistics rmon
show interfaces statistics stg
show interfaces statistics verbose
show interfaces vlan
show ip
show ip access-list extended
show ip arp -s
show ip arp static-mcastmac
show ip bfd
show ip bfd interfaces
show ip bfd neighbors
show ip bfd neighbors next-hop
show ip bfd stats
show ip bgp aggregates
show ip bgp cidr-only
show ip bgp conf
show ip bgp confederation
show ip bgp dampened-paths
show ip bgp flap-damp-config
show ip bgp imported-routes
show ip bgp neighbors
show ip bgp neighbors A.B.C.D
show ip bgp networks
show ip bgp peer-group
show ip bgp redistributed-routes
show ip bgp route
show ip bgp stats
show ip bgp summary
show ip bgp vpnv4
show ip dhcp-relay
show ip dvmrp
show ip dvmrp interface
show ip dvmrp neighbor
show ip dvmrp next-hop
show ip dvmrp route
show ip ecmp
show ip forward-protocol udp portfwd
show ip igmp access
show ip igmp cache
show ip igmp group
show ip igmp igap
show ip igmp igap counters
show ip igmp igap group
show ip igmp interface
show ip igmp mrdisc
show ip igmp mrdisc neighbors
show ip igmp router-alert
show ip igmp sender
show ip igmp snooping
show ip igmp snoop-trace
show ip igmp ssm
show ip igmp ssm-map
show ip igmp static
show ip igmp stream-limit interface
show ip ipfix
show ip ipfix export
show ip ipfix hash-statistics
show ip ipvpn route-target
show ip mroute hw-group-prune-state
show ip mroute hw-group-trace
show ip mroute hw-resource-usage
show ip mroute next-hop
show ip mroute route
show ip mroute static-source-group
show ip msdp count
show ip msdp mesh-group
show ip msdp peer
show ip msdp rpf
show ip msdp sa-cache
show ip msdp sa-check source
show ip msdp show-all
show ip msdp summary
show ip ospf
show ip ospf accept
show ip ospf area
show ip ospf area-range
show ip ospf ase
show ip ospf authentication interface
show ip ospf default-cost
show ip ospf host-route
show ip ospf ifstats
show ip ospf int-auth
show ip ospf interface
show ip ospf int-timers
show ip ospf lsdb
show ip ospf neighbor
show ip ospf neighbors interface
show ip ospf port-error
show ip ospf redistribute
show ip ospf stats
show ip ospf virtual-link
show ip pgm
show ip pgm interface
show ip pgm interface statistics nak
show ip pgm interface statistics parity
show ip pgm retransmit
show ip pgm session
show ip pim active-rp
show ip pim bsr
show ip pim interface
show ip pim mode
show ip pim mroute
show ip pim neighbor
show ip pim rp-candidate
show ip pim rp-hash
show ip pim static-rp
show ip pim virtual-neighbor
show ip prefix-list
show ip redistribute
show ip rip interface
show ip rip redistribute
show ip route
show ip route a.b.c.d
show ip route count-summary
show ip rsmlt
show ip rsmlt edge-support
show ip source binding
show ip tcp statistics
show ip traffic-filter
show ipv6 address interface
show ipv6 dhcp-relay counters
show ipv6 dhcp-relay fwd-path
show ipv6 dhcp-relay interface
show ipv6 forwarding
show ipv6 global
show ipv6 interface
show ipv6 mld-cache interface
show ipv6 mld interface
show ipv6 nd-prefix interface
show ipv6 neighbor
show ipv6 ospf
show ipv6 ospf area
show ipv6 ospf int-timers
show ipv6 ospf lsdb
show ipv6 ospf neighbor
show ipv6 ospf vlan interface
show ipv6 prefix-list
show ipv6 route static
show ipv6 TCP
show ipv6 trace
show ipv6 tunnel
show ipv6 UDP
show ipv6 vrrp address
show ipv6 vrrp interface
show ipv6 vrrp statistics
show ip verify source
show ip vrrp address
show ip vrrp interface vlan
show ip vrrp statistics
show isis area
show isis spbm drop-stats port last drop
show isis spbm drop-stats port rpfc-multicast-sa
show isis spbm drop-stats port rpft-unicast-sa
show isis spbm drop-stats port unknown-multicast-da
show isis spbm drop-stats port unknown-unicast-da
show isis spbm ip-unicast-fib
show isis spbm nick-name
show isis spbm show-all
show ist
show lacp
show lacp interface
show license
show link-flap-detect
show log file
show logging config
show logging file
show logging level
show logging transferfile
show mirror-by-port
show mlt error collision
show mlt error main
show mlt stats
show monitor-statistics
show mpls basic
show mpls ftn
show mpls ilm
show mpls ldp
show mpls ldp bindings
show mpls ldp discovery
show mpls ldp interface
show mpls ldp neighbor
show mpls ldp route
show mpls ldp session
show mpls ldp summary
show mpls mtu
show mpls rsvp
show mpls rsvp explicit-path
show mpls rsvp interface
show mpls rsvp neighbor
show mpls rsvp paths
show mpls rsvp resource
show mpls rsvp static-ip lsp
show mpls statistics ldp
show mpls statistics receive
show mpls statistics rsvp
show mpls statistics transmit
show multicast mlt-distribution
show multicast square-smlt
show nsna client
show nsna interface
show ntp server
show pcap
show pcap capture-filter
show pcap dump
show pcap port
show pcap stats
show ping-snoop
show pluggable-optical-module
show ports statistics ospf extended
show ports statistics ospf main
show ports statistics ospf main
show port statistics wis felinecurrent
show port statistics wis felineinterval
show port statistics wis fepathcurrent
show port statistics wis fepathinterval
show port statistics wis linecurrent
show port statistics wis lineinterval
show port statistics wis pathcurrent
show port statistics wis pathinterval
show port statistics wis sectioncurrent
show port statistics wis sectioninterval
show port statistics wis sonetmedium
show qos 802.1p-override
show qos egressmap
show qos egress-queue-set
show qos eqmap
show qos ingressmap
show qos policer
show qos policy-config
show qos shaper
show qos statistics
show qos statistics egress-queue-set
show qos statistics policy
show radius
show radius-server
show radius-server statistics
show radius snmp
show rmon
show rmon alarm
show rmon event
show rmon history
show rmon log
show rmon stats
show routing statistics
show routing statistics interface
show running-config
show slot
show slpp
show slpp interface
show smlt
show snmplog
show snmp-serve host
show snmp-server
show snmp-server notify-filter
show sonet statistic interfaces pos activealarms
show sonet statistic interfaces pos felinecurrent
show sonet statistic interfaces pos felineinterval
show sonet statistic interfaces pos fepathcurrent
show sonet statistic interfaces pos fepathinterval
show sonet statistic interfaces pos linecurrent
show sonet statistic interfaces pos lineinterval
show sonet statistic interfaces pos linkstatus
show sonet statistic interfaces pos lqrstatus
show sonet statistic interfaces pos pathcurrent
show sonet statistic interfaces pos pathinterval
show sonet statistic interfaces pos pppiftbl
show sonet statistic interfaces pos sectioncurrent
show sonet statistic interfaces pos sectioninterval
show sonet statistic interfaces pos sonetmediumtbl
show spanning-tree bpdu-filtering
show spanning-tree config
show spanning-tree mstp config
show spanning-tree mstp port role
show spanning-tree mstp statistics
show spanning-tree mstp status
show spanning-tree port detail
show spanning-tree rstp config
show spanning-tree rstp port role
show spanning-tree rstp port statistics
show spanning-tree rstp port status
show spanning-tree rstp statistics
show spanning-tree rstp status
show spanning-tree status
show spanning-tree stp config
show spanning-tree stp status
show spanning-tree vlans
show spbm
show ssh
show sys
show sys flags
show sys-info
show syslog
show syslog host
show sys perf
show sys performance
show sys power
show sys power global
show sys power power-supply
show sys power slot
show sys software
show tacacs
show tech
show telnet-access
show test all
show test artable
show test fabric
show trace
show users
show vlacp interface
show vlan advance
show vlan autolearn-mac
show vlan brouter-port
show vlan dvmrp
show vlan idsvlan
show vlan mac-address-filter
show vlan mac-address-static
show vlan manual-edit-mac
show vlan members
show vlan srcmac
show vlan static-mcastmac
show wireless switch
show wireless-switch lb-controller
show wireless-switch mac-address-entry
show wireless switch peer-advertized-vlans
show wireless-switch peer-devices
show wireless-switch tunnel
show wireless-switch tunnel-statistics
show wireless-switch tunnel-statistics bridging
show wireless-switch tunnel-statistics keepalive
show wireless-switch tunnel-statistics routing
show wireless-switch vlan-map
show wireless-switch vlan-reservation
show wireless-switch vlan-servers
source file
| B | C | D | F | I | L | M | P | Q | R | S | T | Back to top
T
terminal more disable
test artable
test fabric
test hardware
test led
trace auto module
trace flags isis
trace ipv6
trace level
traceroute
S
show ip arp interface
M
manual-area
multicast enable
multicast fwd-cache-timeout
mvpn fwd-cache-timeout
| M | S | Back to top
S
spbm b-vid
spbm nick-name
spbm smlt-peer-system-id
spbm smlt-virtual-bmac
D
debug spbm isis recompute-fib
debug spbm isis recompute-fib-download
| D | L | S | Back to top
L
l2tracemroute source group cvlan
l2tracemroute source group vrf priority ttl
| D | L | S | Back to top
S
show ip arp inspection vlan
show ip dhcp snooping binding
show ip dhcp snooping interface
show ip dhcp snooping vlan
show isis
show isis adjacencies
show isis int-auth
show isis int-ckt-level
show isis int-counters
show isis interface
show isis int-l1-cntl-pkts
show isis int-l2-cntl-pkts
show isis int-timers
show isis lsdb
show isis manual-area
show isis net
show isis spbm ip-multicast route
show isis spbm i-sid
show isis spbm multicast-fib
show isis spbm unicast-fib
show isis spbm unicast-tree
show isis statistics
show isis system-id
show vlan i-sid
show vlan mac-address-entry
show vlan remote-mac-table
show web-server
D
default ip igmp snoop-querier
default ip igmp snoop-querier-addr
| D | I | N | Back to top
I
ip igmp snoop-querier
ip igmp snoop-querier-addr
| D | I | N | Back to top
N
no ip igmp snoop-querier
no ip igmp snoop-querier-addr
I
i-sid
isis redistribute
I
ip bgp redistribute isis route-map
ip ospf redistribute isis metric-type
ip ospf redistribute isis subnets
ip redistribute isis
ip redistribute isis enable
ip redistribute isis metric
ip redistribute isis route-policy
ip vrf
ip vrf max-routes
| I | M | S | Back to top
M
mvpn enable
| I | M | S | Back to top
S
show ip vrf
show ip vrf max-routes
E
enable
| E | I | L | M | R | T | V | Back to top
I
interface-ip
| E | I | L | M | R | T | V | Back to top
L
lb-controller
| E | I | L | M | R | T | V | Back to top
M
mgmt-ip
| E | I | L | M | R | T | V | Back to top
R
remote-vlan-stg
| E | I | L | M | R | T | V | Back to top
T
tcp-udp-base-port
| E | I | L | M | R | T | V | Back to top
V
vlan-map
vlan-map lvid
vlan-map name
vlan-map weight
vlan-reservation