Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
TRANSMIT
RED
BLACK
BLACK WHITE
WHITE GREEN
SHIELD
INTERNAL CONNECTIONS
FIGURE 1
GENERAL The 550L may be wired for balanced or unbalanced
The Shure 550L is an omnidirectional dynamic base station
operation. For unbalanced operation, the green cable wire
microphone with a frequency response specially tailored for
is connected to the audio input, the white cable wire is
voice intelligibility. It is equally useful for radio
connected to the audio ground, and the shield is connected
communications, paging and dispatching systems, and its
to the chassis ground. See Table 1.
low-impedance connection makes it adaptable to most PA
For balanced operation, the green cable wire is connected
amplifiers. The low-impedance design also makes it useful
to the audio input positive (+), the white wire is connected to
for long runs of cable, or under severe hum disturbance
the audio negative (-), and the shield is connected to the
conditions.
chassis ground. See Table 1.
The microphone is not affected by heat or humidity. Its
Table 1. Cable-to-Connector Wiring
exclusive ARMO-DUR® case is immune to oil, grease,
WIRE FUNCTION XLR 1/4 IN. PHONE
fumes, salt spray, sun, rust, and corrosion–and is COLOR CONNECTOR PLUG
outstanding in its ability to resist mechanical shocks and INPUT TYPE
vibration. The “Million-Cycle” leaf-type switch is designed to GREEN AUDIO PIN 2 TIP
withstand rigorous operating conditions and constant use. UNBALANCED WHITE AUDIO GROUND PIN 3 SLEEVE
• Crisp, natural, high-intelligibility voice response BALANCED WHITE AUDIO - PIN 3 RING
SHIELD CHASSIS GROUND PIN 1 SLEEVE
• Fingertip control bar actuates microphone circuit and exter-
nal relay or control circuit
NOTE: The red and black wires are not part of the audio circuit.
• Long-life switch meets rigorous requirements of communi-
These wires provide a contact closure when the microphone
cations and paging systems
switch is depressed. This closure may be used to control an exter-
• Sturdy, high-impact ARMO-DUR base and microphone nal relay or transmit/receive circuit.
case resists corrosion
• Reliability under all operating conditions IMPEDANCE MATCHING
Low-impedance operation is extremely useful where long
• Neoprene feet prevent microphone slipping
cable lengths are required, or under conditions of severe
PRESS-TO-TALK SWITCH OPERATION hum disturbance. The permissible cable length is practically
The fingertip control bar is a non-locking switch; simply unlimited, since neither response nor level is appreciably
depress the control bar and release after transmission. affected. Shure A95 Series Line Matching Transformers are
available for use in those cases where a low-impedance
WIRING
microphone is to be used with an amplifier with a
Figure 1 shows the internal wiring of the 550L microphone. high-impedance input. These transformers provide a proper
impedance match between a 19- to 300-ohm microphone
and a high-impedance input, and are available with various
input and output connectors.
ÉÉ ÉÉÉ
(2-5/8 IN.)
150 to 6,000 Hz (see Figure 2) (2-1/4 IN.)
ÉÉ ÉÉÉ
+10 44.4 mm
(1-3/4 IN.)
ÉÉ ÉÉÉ
dB
264 mm
(10-3/8 IN.)
–10
2 3 4 5 6 7 89 2 3 4 5 6 7 89
20 50 100 1000 10000 20000
Hz 2.8 mm 12.7 mm
(7/64 IN.) (1/2 IN.)
TRAVEL
TYPICAL FREQUENCY RESPONSE
FIGURE 2 28.6 mm
Polar Pattern
(1-1/8 IN.)
Omnidirectional 4.8 mm
(3/16 IN.)
149 mm 57 mm
Impedance (at 1,000 Hz) (5-7/8 IN.) (2-1/4 IN.)