Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
CAS RN
7647-14-5
8028-77-1
11062-32-1
11062-43-4
418758-90-4
SUPPLIER
Company: Scomi Oiltools
Address:
5th Floor, Wisma Chase Perdana
Off Jalan Semantan
Damansara Heights, Kuala Lumpur
MALAYSIA - 50490
Telephone: +60 3 2080 5000
Emergency Tel: +800- CHEMCALL
Fax: +60 3 2080 5033
PRODUCT USE
Drilling & Completion Fluid Chemical
SYNONYMS
NaCl, "common salt", halite, rocksalt, "rock salt", "sea salt", saline, salt, "Saxa table
salt", "dendritis white crystal", "Natrii chloridum", "solar salt", "vacuum salt", "PDV
salt", "butter salt", "Merck 10241", "Sigma S9625", APS, "Chem-Supply sodium chloride LR
SL046",
SWALLOWED
Although ingestion is not thought to produce harmful effects (as classified under EC
Directives), the material may still be damaging to the health of the individual,
following ingestion, especially where pre-existing organ (e.g liver, kidney) damage is
evident. Present definitions of harmful or toxic substances are generally based on doses
producing mortality rather than those producing morbidity (disease, ill-health).
Gastrointestinal tract discomfort may produce nausea and vomiting. In an occupational
setting however, ingestion of insignificant quantities is not thought to be cause for
concern.
Use as a food additive indicates good tolerance of small amounts, but excessive amounts
or overuse may bring irritant and/or harmful effects.
EYE
Limited evidence exists, or practical experience suggests, that the material may cause
eye irritation in a substantial number of individuals and/or is expected to produce
significant ocular lesions which are present twenty-four hours or more after instillation
into the eye(s) of experimental animals. Repeated or prolonged eye contact may cause
inflammation characterised by temporary redness (similar to windburn) of the conjunctiva
(conjunctivitis); temporary impairment of vision and/or other transient eye
damage/ulceration may occur.
The material may produce moderate eye irritation leading to inflammation. Repeated or
prolonged exposure to irritants may produce conjunctivitis.
SKIN
Limited evidence exists, or practical experience predicts, that the material either
produces inflammation of the skin in a substantial number of individuals following direct
contact, and/or produces significant inflammation when applied to the healthy intact skin
of animals, for up to four hours, such inflammation being present twenty-four hours or
more after the end of the exposure period. Skin irritation may also be present after
prolonged or repeated exposure; this may result in a form of contact dermatitis
(nonallergic). The dermatitis is often characterised by skin redness (erythema) and
swelling (oedema) which may progress to blistering (vesiculation), scaling and thickening
of the epidermis. At the microscopic level there may be intercellular oedema of the
spongy layer of the skin (spongiosis) and intracellular oedema of the epidermis.
Skin contact is not thought to have harmful health effects (as classified under EC
Directives); the material may still produce health damage following entry through wounds,
lesions or abrasions.
The material may accentuate any pre-existing skin condition.
Contact with cuts, abraded skin is painful, but this is transient.
The material may cause skin irritation after prolonged or repeated exposure and may
produce a contact dermatitis (nonallergic). This form of dermatitis is often
characterised by skin redness (erythema) and swelling epidermis. Histologically there may
be intercellular oedema of the spongy layer (spongiosis) and intracellular oedema of the
epidermis.
INHALED
The material is not thought to produce adverse health effects or irritation of the
respiratory tract (as classified by EC Directives using animal models). Nevertheless,
good hygiene practice requires that exposure be kept to a minimum and that suitable
control measures be used in an occupational setting.
Not normally a hazard due to non-volatile nature of product.
EYE
If this product comes in contact with the eyes:
Wash out immediately with fresh running water.
Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and
moving the eyelids by occasionally lifting the upper and lower lids.
If pain persists or recurs seek medical attention.
Removal of contact lenses after an eye injury should only be undertaken by skilled
personnel.
SKIN
If skin or hair contact occurs:
Flush skin and hair with running water (and soap if available).
Seek medical attention in event of irritation.
INHALED
If dust is inhaled, remove from contaminated area.
Encourage patient to blow nose to ensure clear passage of breathing.
If irritation or discomfort persists seek medical attention.
NOTES TO PHYSICIAN
Treat symptomatically.
FIRE/EXPLOSION HAZARD
Non combustible.
Not considered a significant fire risk, however containers may burn.
Decomposes on heating and produces toxic fumes of: chlorides and caustic compounds.
FIRE INCOMPATIBILITY
No known incompatibility with normal range of industrial materials.
PERSONAL PROTECTION
Glasses:
Safety Glasses.
Chemical goggles.
Gloves:
1.NATURAL RUBBER 2.NITRILE
Respirator:
Particulate
MAJOR SPILLS
Clear area of personnel and move upwind.
Alert Fire Brigade and tell them location and nature of hazard.
Control personal contact by using protective equipment and dust respirator.
Prevent spillage from entering drains, sewers or water courses.
Avoid generating dust.
Sweep, shovel up. Recover product wherever possible.
Put residues in labelled plastic bags or other containers for disposal.
If contamination of drains or waterways occurs, advise emergency services.
_____________________________________________________
+ + + + + +
_____________________________________________________
+: May be stored together
O: May be stored together with specific preventions
X: Must not be stored together
SUITABLE CONTAINER
Multi-ply paper bag with sealed plastic liner or heavy gauge plastic bag.
NOTE: Bags should be stacked, blocked, interlocked, and limited in height so that they
are stable and secure against sliding or collapse. Check that all containers are clearly
labelled and free from leaks. Packing as recommended by manufacturer.
STORAGE INCOMPATIBILITY
Food grade materials must be protected from all possible contaminants.
Keep dry and Segregate from strong acids.
STORAGE REQUIREMENTS
Keep dry.
Store under cover.
Protect containers against physical damage.
Observe manufacturer's storing and handling recommendations.
MATERIAL DATA
PERSONAL PROTECTION
EYE
Safety glasses with side shields; or as required,
Chemical goggles.
Contact lenses may pose a special hazard; soft contact lenses may absorb and
concentrate irritants. A written policy document, describing the wearing of lens or
restrictions on use, should be created for each workplace or task. This should include a
review of lens absorption and adsorption for the class of chemicals in use and an account
of injury experience. Medical and first-aid personnel should be trained in their removal
and suitable equipment should be readily available. In the event of chemical exposure,
begin eye irrigation immediately and remove contact lens as soon as practicable. Lens
should be removed at the first signs of eye redness or irritation - lens should be
removed in a clean environment only after workers have washed hands thoroughly. [CDC
NIOSH Current Intelligence Bulletin 59].
HANDS/FEET
No special equipment needed when handling small quantities.
OTHERWISE: Wear chemical protective gloves, eg. PVC.
OTHER
Overalls.
Eyewash unit.
RESPIRATOR
Powered
Protection Half-Face Full-Face
Air
Factor Respirator Respirator
Respirator
P1 Air- PAPR-P1
10 x ES --
line* -
50 x ES Air-line** P2 PAPR-P2
100 x ES - P3 -
Air-line* -
100+ x
- Air-line** PAPR-P3
ES
ENGINEERING CONTROLS
Use in a well-ventilated area.
Local exhaust ventilation is required where solids are handled as powders or crystals;
even when particulates are relatively large, a certain proportion will be powdered by
mutual friction.
Exhaust ventilation should be designed to prevent accumulation and recirculation of
particulates in the workplace.
If in spite of local exhaust an adverse concentration of the substance in air could
occur, respiratory protection should be considered. Such protection might consist of:
(a): particle dust respirators, if necessary, combined with an absorption cartridge;
(b): filter respirators with absorption cartridge or canister of the right type;
(c): fresh-air hoods or masks
Build-up of electrostatic charge on the dust particle, may be prevented by bonding and
grounding.
Powder handling equipment such as dust collectors, dryers and mills may require
additional protection measures such as explosion venting.
Air contaminants generated in the workplace possess varying "escape" velocities which, in
turn, determine the "capture velocities" of fresh circulating air required to efficiently
remove the contaminant.
Simple theory shows that air velocity falls rapidly with distance away from the opening
of a simple extraction pipe. Velocity generally decreases with the square of distance
from the extraction point (in simple cases). Therefore the air speed at the extraction
point should be adjusted, accordingly, after reference to distance from the contaminating
source. The air velocity at the extraction fan, for example, should be a minimum of 4-10
m/s (800-2000 f/min) for extraction of crusher dusts generated 2 metres distant from the
extraction point. Other mechanical considerations, producing performance deficits within
the extraction apparatus, make it essential that theoretical air velocities are
multiplied by factors of 10 or more when extraction systems are installed or used.
APPEARANCE
Odourless, colourless, transparent crystals or white crystalline powder;
completely soluble in water.
Available as Rocksalt (crude), Technical, Pure, Food grade, BP grades; also
solar salt, vacuum salt, sea salt and common salt.
A saturated solution of solar salt is approximately pH 8 and vacuum salt
is pH 9.5 - 11.0
According to the European Waste Catalogue, Waste Codes are not product specific but
application specific. Waste Codes should be assigned by the User based on the application
in which the product is used.
REGULATIONS
No data available for sodium chloride as CAS: 8028-77-1, CAS: 11062-32-1, CAS: 11062-43-4
, CAS: 418758-90-4.
This document is copyright. Apart from any fair dealing for the purposes of
private study, research, review or criticism, as permitted under the Copyright
Act, no part may be reproduced by any process without written permission from
CHEMWATCH. TEL (+61 3) 9572 4700.