Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Automotive
Glass Products
Catalog
Contents
3M Auto Glass Urethane Adhesives 3M Aerosol Adhesives,
Cleaners & Lubricants continued...
3 Fast Cure Auto Glass Windshield Adhesive
3 Auto Glass Urethane Windshield Adhesive-(HV)
9 Anti-Seize Lubricant
3 Auto Glass Urethane Windshield Adhesive-(MV)
9 Super Trim Adhesive
3 Windo-Weld Super Fast Urethane
9 General Trim Adhesive
4 Rapid Two-Part Auto Glass Urethane Windshield
10 Spray Trim Adhesive
Adhesive (RTP)
10 Glass Cleaner
3M Primers 10 General Purpose Adhesive Cleaner
4 Clear Primer (Step 1) 10 Release Agent
4 Black Primer (Step 2) 11 Lithium Lube
5 Single Use Primer Applicators 11 Spray Lube
5 Primer Daubers 11 Silicone Lubricant (Dry Type)
11 Silicone Lubricant Plus (Wet Type)
3M Damming Products 12 4-Way Spray Lubricant
5 Single-Sided Foam Dam Tape 12 Super Weatherstrip Adhesive
5 Foam Spacer Blocks 12 Weatherstrip Adhesive-Black
6 Windo-Weld Ribbon Sealer 12 Quick Fix Adhesive
6 Windo-Weld Resealant (Flow Grade)
3M Aerosol Adhesives,
3M Automotive Windshield
Cleaners & Lubricants
Replacement Procedures
8 Rear View Mirror Adhesive
19-20 Replacement Instructions
8 Super Glue Gel
1
9 Automix Fast Cure Epoxy Adhesive
The Windshield...A Structural Member of Todays Automobile
In the early 1980s auto makers responded to skyrocketing fuel prices by reducing vehicle weights and
increasing vehicle aerodynamics. Flush-mounted glass and the windshield becoming a structural part of the
vehicle were results of this effort.
As the windshield became a designed safety feature of the vehicle, windshield replacement technology
changed quickly and corresponding regulations emerged. Department of Transportation regulations 212 and
216 set standards for the wind-
shield retention and roof crush
during rollover. And, with the
windshield a designed safety
feature, glass shops had to
consider specific regulations
such as the Motor Vehicle Safety
Act (see bottom of page). Glass
shops were now responsible for
replacing glass to meet OEM
specifications.
3M is an innovator in the
development of windshield
replacement products and
methods.
3M is the only urethane manufacturer to have two windshield urethane adhesives that are both Carlite by
Visteon approved and officially licensed by NASCAR:
3M Rapid Two Part Auto Glass Urethane passed the rigorous Carlite by Visteon 35 mph test with
100% retention in 2 hours at 25 degrees using 3Ms cold temperature procedure.
3M Fast Cure Auto Glass Urethane (one-part, high viscosity urethane) passed the Carlite by Visteon
rigorous 35 mph test in 8 hours at 70 degrees fahrenheit and 50% relative humidity. At 90 degrees
fahrenheit and 80% relative humidity, 3M Fast Cure Auto Glass Urethane reaches an Overlap Shear
Strength of 250 psi in 2 hours and 150 psi in only 1 hour. This means 3M Fast Cure Auto Glass
Urethane is the fastest curing 3M one part auto glass urethane available.
Motor Vehicle Safety Act-Section 1397 (a) (2) (a) No...dealer...repair business
shall knowingly render inoperative, in whole or in part, any device or element
of design installed on or in a motor vehicle...unless...such...vehicle...will not be
used...during the time such device or element or design is rendered inoperative.
2
3M Auto Glass Urethane Adhesives
3M Primers
4
3M Primers
3M Primer Daubers
To be used with both clear and black primers
3M Damming Products
5
3M Damming Products
7
3M Aerosol Adhesives, Cleaners and Lubricants
3M Structural Adhesive
Two-part general purpose structural adhesive that may be used for bonding metal, glass and
plastic
May be used for trim, fiberglass and flexible body parts repair
Use for sidelite channel bonding
Easy mixing
Sets up quickly
Spreads smoothly
Cures to an extremely strong bond
* Used with 3M AutoMix Applicator Gun (Part. No. 08191) and Mixing Nozzles-Clear (Part No.
08197)
8
3M Aerosol Adhesives, Cleaners and Lubricants
*Used with 3M Automix Applicator Gun (Part No. 08191) and Mixing Nozzles-Clear (Part No.
08197)
3M Anti-Seize Lubricant
Lubricates and prevents corrosion
High temperature formula
Prevents seizing of spark plugs, cylinder head and exhaust bolts
Prevents seizing of windshield wiper arm onto post
9
3M Aerosol Adhesives, Cleaners and Lubricants
3M Glass Cleaner
Excellent all-around cleaner
For windshields, mirrors, chrome, metal, or plastic trim (including Lexan)
Safe, non-flammable formula
3M Release Agent
A blend of solvents
Softens bond between weatherstrip and metal, auto glass and rubber grommets
Works on all rubber set installations
10
3M Aerosol Adhesives, Cleaners and Lubricants
3M Lithium Lube
Actual high solids white grease in the convenience of an aerosol can
Eliminates messiness
Extra heavy bodied lubricant
Snorkel spray
Excellent for metal-to-metal moving parts
Resists heat and moisture
Protects metal against corrosion
3M Spray Lube
A clear, flowable, high-performance, general purpose grease
Designed to be water resistant
Can be used to lubricate many items including hinges, latches and seat tracks
Flows as a liquid then sets up to a uniform coating of grease
11
3M Aerosol Adhesives, Cleaners and Lubricants
3M Weatherstrip Adhesive-Black
Fast-drying adhesive used for bonding and sealing weatherstripping
Also an excellent adhesive for new EPDM weatherstripping
Easy to apply
Remains flexible
Waterproof
12
3M Applicators & Accessories
3M Mixing Nozzles-Clear
For use with 3M Automix Channel Bonding and Sidelite Adhesive (PN 08641) and 3M
Automix Fast Cure Epoxy Adhesive (PN 08107)
3M Applicator Guns
Available for easiest application of 3M Automotive Adhesives and Sealers
3M Shop/Glass Stand
Sturdy, portable shop stand for convenient and efficient repairing of parts or for glass preparation
Portable for easy set up and storage
Constructed of 16 gauge 1 square tubing
Provides maximum floor surface for support and stability
Full 3/8 thick, durable rubber pads to protect parts and glass
Red epoxy powder paint for lasting durability and appeal
Maximum weight capacity: 250 lbs.
To order, call Shopware at 1-800-877-9344
OUS FAX (952) 392-2018
13
3M Abrasive Products
PART NO. SIZE GRADE COLOR DISCS PER BOX BOXES PER CASE
07524 2 50 Green 10 4
07525 2 80 Yellow 10 4
07526 3 50 Green 10 4
07527 3 80 Yellow 10 4
07528 2 120 White 10 4
07529 3 120 White 10 4
07530 1 50 Green 10 4
07531 1 80 Yellow 10 4
07532 1 120 White 10 4
1 Discs MOS =30,000 RPM
2 Discs MOS =25,000 RPM
3 Discs MOS =18,000 RPM
14
3M Aerosol Adhesives, Cleaners and Lubricants
PART NO. SIZE GRADE DISCS PER BOX BOXES PER CASE
07542 3 50 10 4
07543 3 80 10 4
07544 3 120 10 4
(Contact your local 3M sales representative to purchase these items)
15
3M Abrasive Products
3M Duo-Glass Belts
Specially designed for glass and mirror grinding, finishing, and polishing
New SINE-LOK butt splice with uninterrupted mineral coating reduces edge chipping and
belt bumping at the splice
SINE-LOK splice allows the belt to run in either direction eliminating need for directional
arrow during installation
Synthetic backing is stronger than conventional cloth belts
Provides greater support than conventional belts
Waterproof resin bond permits wet or dry use of belt
16
Your 3M Auto Glass
Certification Kit Materials Include:
The 3M Certification Program is an important part of your commitment to quality.
Use these materials to show your customers you took the time and effort to be
trained, tested, trusted. Let your installers know youre proud of them, too, when
you give them their certificates and buttons.
1. Certificate
Given to each installer when he or she passes the certification test.
2. Hang Tag
Place in customers cars after their windshields have been replaced.
2. Brochure
Give to customers if they have any questions about the program.
4. Table Tent
Place in waiting area or checkout desk.
5. Door Sticker
Place on your front door or on any window in the shop.
6. Reply Card
Use this to order more certification program materials.
7. Patch
Have each certified employee wear these with pride.
8. Van Sticker
Place on vans to show you care about quality.
17
18
3M Automotive Windshield Replacement Procedures
These instructions describe the proper prevent scraping paint off the pinchweld car body to fill voids.
use of 3M Auto Glass urethanes and and exposing bare metal. NOTE: On
related 3M glass shop products and are urethane installations, it is recommend- 16. Remove masking tape alignment
intended for use as a supplement to ed that a thin film of the old urethane be strips.
detailed service manuals and instruc- left on the pinchweld and fresh urethane
tions provided by automotive manufac- bonded to remaining film. When 17. Replace moldings, windshield
turers. Automobile manufacturers removing butyl tape or unknown wipers and other trim removed in
instructions should be followed when material, remove all old material from Step 1.
removing automotive trim and moldings pinchweld before applying fresh ure-
as well as other special requirements thane. 18. Clean any excess urethane with
pertaining to specific car models. adhesive cleaner.
7. Prime any bare metal scratches with
Note: The products and procedures 3M Black Primer, (Step 2) (P/N
presented here may be applicable to 08684, 08686). NOTE: When exces- Full Cut Method Without Dam
quarter and backlite replacements. sive abrasive cleaning is required, prime
However, for detailed instructions by car pinchweld metal with a 2 part epoxy Materials Using: 3M Fast
model, you should refer to information automotive paint primer and allow to Cure Auto Glass Urethane-
available from the automobile manufac- cure properly. Apply 3M Black
turer. Primer (Step 2) to repaired area and (High Viscosity) Part Numbers
allow to dry for at least 5 minutes.
08689, 08690, 08566 or 3M
Full Cutout Method With Dam 8. Clean inside surface of glass with
3M Glass Cleaner, P/N 08888 taking Auto Glass Urethane-High
Materials Using 3M Auto care to clean surface where the ure-
thane bond will be made.
Viscosity Part Numbers
Glass Urethane-Medium
08696, 08698, 08565
Viscosity Part Numbers 9. Apply a thin film of 3M Clear
Primer (Step 1), (P/N 08683, 08685 or The following instructions cover
08693, 08695, or 08564 P/N 08691) with a clean wipe. Wipe off replacement procedure for urethane
excess primer while still wet with a bonded automotive windshields using
The following instructions cover clean lint free cloth. Allow primer to dry the full cut out procedure without the
replacement procedure for urethane for at least 5 minutes. (Repeat, Step 9) use of a dam material. High viscosity
bonded automotive windshields using urethane products provide windshield
the full cut out procedure with dam 10. Apply 3M Black Primer (Step 2) support while the cure is attained to
material. The dam material provides (P/N 08684, 08686, or 08692) over the provide structural strength.
the proper setting height. primed 3/4 inch of glass. Allow primer
to dry for at least 5 minutes. 1. If necessary remove windshield wiper
1. If necessary, remove windshield arms and trim necessary to expose the
wiper arms and trim necessary to 11. Apply dam material to inside edge entire perimeter of glass.
expose the entire perimeter of glass. of pinchweld or 3M Foam Spacer
Blocks, PN 08529. 2. Clean dirt and debris from around the
2. Clean dirt and debris from around the pinchweld area before cutting out the
pinchweld area before cutting out the 12. Cut tip to desired shape and size glass and again after the glass is cut
glass and again after the glass is cut large enough to be slightly higher than out to minimize contamination.
out to minimize contamination. the dam material. A triangular shaped
notch will provide the desired bead 3. Cut into existing urethane around
3. Cut into existing urethane around shape and height. A height of 1/2 to entire perimeter of glass with a utility
entire perimeter of glass with a utility 9/16-inch and a 1/4 - 5/16-inch base is knife cutting as close to edge of the
knife. Cut as close to edge as possible. suggested. NOTE: When installing glass as possible.
encapsulated glass, apply a bead high
4. Cut out glass with appropriate enough to assure glass contact before 4. Cut out glass with appropriate
removal tools keeping as close to the encapsulation contacts the car body removal tools keeping as close to the
glass as possible. Remove the glass and prevents further setting. Back pad- glass as possible. Remove windshield
and repeat Step 2. dling material after setting will not be and repeat Step 2.
possible.
5. Dry set the glass. Align for uniform fit 5. Dry set the glass. Align for uniform fit
and adjust setting blocks as needed for 13. Apply 3M Auto Glass Urethane and adjust setting blocks as needed for
best fit. To allow for sufficient bonding Windshield Adhesive - MV directly onto best fit. To allow for sufficient bonding
of urethane, make sure there is a MINI- the remaining OEM urethane film, of urethane, make sure there is a
MUM of 1/4 inch of glass, in addition to behind and contacting the dam material. MINIMUM of 1/4 inch of glass, in
the space that will be taken up by any addition to the space that will be taken
dam material, around the entire perime- 14. Position the glass by aligning the up by any dam material, around the
ter of the glass. Mark location by apply- masking tape on glass and car body. entire perimeter of the glass. Mark
ing masking tape to windshield and car Press glass in place to assure complete location by applying masking tape to
body. Slit tape at edge of glass. contact with dam material and urethane windshield and car body. Slit tape at
Remove windshield. adhesive. edge of glass. Remove windshield.
6. Remove major portion of old ure- 15. Paddle squeeze out around edge of
thane adhesive from the pinchweld. glass if possible. If necessary, paddle
Use a razor blade knife or utility knife to additional adhesive between glass and
19
6. Remove major portion of old ure- 16. Remove masking tape alignment excessive abrasive cleaning is required,
thane adhesive from the pinchweld. strips. prime pinchweld metal with a 2 part
Use a razor blade knife or utility knife to epoxy automotive paint primer and
prevent scraping paint off the pinchweld 17. Replace moldings, windshield allow to cure properly. Apply 3M
and exposing bare metal. NOTE: On wipers and other trim removed in Black Primer (Step 2) to repaired area
urethane installations, it is recommend- Step 1. and allow to dry for at least 5 minutes.
ed that a thin film of the old urethane be
left on the pinchweld and fresh urethane 18. Clean any excess urethane with an 8. Clean inside surface of glass with
is bonded to remaining film. When adhesive cleaner. 3M Glass Cleaner, PN 08888 taking
removing butyl tape or unknown materi- care to clean surface where the ure-
al, remove all old material from pinch- thane bond will be made.
weld. Full Cut Method Without
9. Apply a thin film of 3M Clear
7. Prime any bare metal scratches with Dam Materials Using Primer (Step 1) P/N 08683, 08685 or
3M Black Primer (Step 2) (P/N 08684
or 08686). NOTE: When excessive
3M Rapid Two-Part Auto 08691 with a clean wipe. Wipe off
excess primer while still wet with a
abrasive cleaning is required, prime Urethane Adhesive (RTP) clean lint free cloth. Allow primer to dry
pinchweld metal with a 2 part epoxy for at least 5 minutes. (Repeat, Step 9)
automotive paint primer and allow to Part Numbers 08533,
cure properly. Apply 3M Black Primer 10. Apply 3M Black Primer (Step 2)
(Step 2) to repaired area and allow to 08534 P/N 08684, 08686 or 08692, over the
dry for at least 5 minutes. primed 3/4 of glass. Allow primer to
The following instructions cover replace- dry for at least 5 minutes.
8. Clean inside surface of glass with ment procedure for urethane bonded
3M Glass Cleaner, P/N 08888 taking automotive windshields using the full 11. If a foam dam was used in the
care to clean surface where the ure- cut out procedure using 3M Rapid OEM application, it is suggested that
thane bond will be made. Two-Part Urethane. foam dam material be replaced. If no
foam dam was used it is suggested that
9. Apply a thin film of 3M Clear 1. If necessary remove windshield wiper the foam dam tape or 3M Foam
Primer (Step 1) (P/N 08683, 08685 or arms and trim necessary to expose the Spacer Blocks, PN 08529 be applied to
08691) to the outer 3/4 inch of the glass entire perimeter of glass. assist in setting the glass when using
with a clean wipe. Wipe off excess 3M Rapid Two-Part Urethane
primer with a clean lint free cloth while 2. Clean dirt and debris from around the Windshield Adhesive (RTP).
still wet. Allow primer to dry for at least pinchweld area before cutting out the
5 minutes. (Repeat, Step 9) glass and again after the glass is cut 12. Cut tip to desired shape and size
out to minimize contamination. large enough to be slightly higher than
10. Apply 3M Black Primer (Step 2) the dam material. A triangular shaped
(P/N 08684, 08686, or 08692) over the 3. Cut into existing urethane around notch will provide the desired bead
primed 3/4 inch of glass. Allow primer entire perimeter of glass with a utility shape and height. A height of 1/2 to
to dry for for at least 5 minutes. knife cutting as close to edge of the 9/16 inch and 1/4 to 5/16 inch base is
glass as possible. suggested. NOTE: When installing
11. If a foam dam was used in the OEM encapsulated glass, apply a bead high
application it is suggested that foam 4. Cut out glass with appropriate enough to assure glass contact before
dam material be replaced. removal tools keeping as close to the encapsulation contacts the car body
glass as possible. Remove windshield and prevents further setting. Back pad-
12. Cut tip to desired shape and size to and repeat Step 2. dling material after setting will not be
provide a bead height sufficient to give impossible.
good contact with the windshield around 5. Dry set the glass. Align for uniform fit
the entire perimeter. A triangular and adjust setting blocks as needed for 13. Position the glass by aligning the
shaped notch will provide the desired best fit. To allow for sufficient bonding of masking tape on glass and car body.
bead shape and height. A height of 1/2 urethane, make sure there is a MINI- Press glass in place to assure complete
inch to 9/16-inch and a 1/4 inch- 5/16- MUM of 1/4 inch of glass, in addition to contact with dam material and urethane
inch base is suggested. NOTE: Where the space that will be taken up by any adhesive.
installing encapsulated glass, apply a dam material, around the entire perime-
bead high enough to assure glass con- ter of the glass. Mark location by apply- 14. Paddle squeeze out around edge of
tact before encapsulation contacts the ing masking tape to windshield and car glass if possible. If necessary, paddle
car body and prevents further setting. body. Slit tape at edge of glass. additional adhesive between glass and
Back paddling material after setting will Remove windshield. car body to fill voids.
not be possible.
6. Remove major portion of old ure- 15. Remove masking tape alignment
13. Apply 3M Auto Glass Urethane thane adhesive from the pinchweld. strips.
Windshield Adhesive High Viscosity, or Use a razor blade knife or utility knife to
3M Fast Cure Auto Glass Urethane, prevent scraping paint off the pinchweld 16. Replace moldings, windshield
directly onto the OEM urethane film on and exposing bare metal. NOTE: On wipers and other trim removed in
the pinchweld or directly to the glass. urethane installations, it is recommend- Step 1.
ed that a thin film of the old urethane is
14. Position the glass by aligning the left on the pinchweld and fresh urethane 17. Clean any excess urethane with an
masking tape on glass and car body. is bonded to remaining film. When adhesive cleaner.
Press glass in place to assure complete removing butyl tape or unknown materi-
contact with the urethane adhesive. al, remove all old material from pinch-
weld.
15. Paddle squeeze out around edge of
glass if possible. If necessary, paddle 7. Prime any bare metal scratches with
additional adhesive between glass and 3M Black Primer (Step 2) (P/N 08684,
car body to fill voids. 08686). NOTE: When
20
3 Branch Offices
Alaska Hawaii Puerto Rico
11151 Calaska Circle 4443 Malaai Street Puerto Rico Industrial Park
Anchorage, Alaska 99515 Honolulu, Hawaii 96818 P.O. Box 100
Telephone: (907) 522-5200 Mail to : P. O. Box 30048 Carolina, Puerto Rico 00986-0100
Fax (907) 522-5200 Honolulu, Hawaii 96820 Telephone: (809) 750-3000
Telephone: (808) 422-2721 Fax (809) 750-3035
Atlanta Fax (808) 422-9557
2860 Bankers Industrial Drive Twin Cities
Atlanta, Georgia 30360 Los Angeles 3130 Lexington Avenue South
Telephone: 1-800-524-6429 6023 South Garfield Avenue Eagan, Minnesota 55121-2239
Fax 1-800-699-7840 Los Angeles, California 90040 Mail to: P.O. Box 33211
Mail to : P. O. Box 54019 Eagan, MN 55133-3211
Chicago Los Angeles, California 90054-4019 C/C 01, Loc 023
4 Westbrook Corporate Center Telephone: 1-800-221-7569 (651) 733-3300
Suite 300 Fax 1-800-648-0871 TRIMINET 733-3300
Westchester, IL 60154-9978 Fax (651) 736-2694
Telephone: 1-800-524-5406 New York
Fax 1-800-421-2483 15 Henderson Drive
West Caldwell, New Jersey 07007
Dallas Mail to : P. O. Box 2076
2121 Santa Anna Avenue West Caldwell, New Jersey 07007
Dallas, Texas 75228-1698 Telephone: 1-800-524-0401
Mail to : P. O. Box 28158 Fax 1-800-769-0945
Dallas, Texas 75228-0158
Telephone: 1-800-524-6431
Fax 1-800-421-4876
Fax On Demand (For Five or Fewer Material Safety Data Sheets) 1-800-305-0419
Internet: www.3M.com/automotive
The brand names 3M, GREEN CORPS, ROLOC, TRI-M-ITE, LONG-MASK, DUO-GLASS, WETORDRY, AUTOMIX,
WINDO-WELD, SCOTCH-BRITE and SCOTCH, are trademarks of Minnesota Mining and Manufacturing Company, St. Paul,
Minnesota 55144-1000
3
Automotive Aftermarket Division Litho in U.S.A. with 3M offset,
Recycled Paper plates, film and proofing systems.
3M Center, Building 223-6N-01 40% - Pre-consumer
St. Paul, MN 55144-1000 10% - Post-consumer 3M 2002 60-4400-8544-1(22.5)ii