Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
VERSION 1
INSTALLATION CARGO LINERS 2017 CR-V Issue Date
INSTRUCTIONS DEC 2016
Template C
15 *Rivets
(P/N 08P42-TLA-100)
14 *Rivets
(P/N 08P42-TLA-100A)
2016 American Honda Motor Co., Inc. All Rights Reserved. AII04527-18 (1612) 08P42-TLA-1000-90 1 of 13
Illustration of the Cargo Liners in the Vehicle INSTALLATION
RIGHT CARGO
LINER Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
do-it-yourselfers.
2 of 13 AII04527-18 (1612) 2016 American Honda Motor Co., Inc. All Rights Reserved.
Installing the Cargo Liners 2. Fold down the left and right rear seat-backs.
1. If equipped, remove the tonneau cover.
LEFT REAR RIGHT REAR
SEAT-BACK SEAT-BACK
(Fold down.) (Fold down.)
TONNEAU
LEFT QUARTER COVER
PILLAR TRIM HOLDER
SPRING-LOADED
END
(Compress.)
2 TABS
TONNEAU (Fold.)
COVER
TEMPLATE A
2016 American Honda Motor Co., Inc. All Rights Reserved. AII04527-18 (1612) 3 of 13
4. Line up template A with the right rear side trim panel If the vehicle is equipped with a subwoofer, continue
as shown. Tape template A to the right rear side trim with step 5; otherwise, go to step 6.
panel with masking tape.
With subwoofer
Line up with the 5. Using a pushpin, pierce the right rear side trim panel
Line up. curve end. Line up.
through template A as shown. Remove template A.
Go to step 7.
NOTE: There are several marks on template A.
Before piercing the right rear side trim panel, verify
you have the correct locations. Make sure to pierce
the marks perpendicular to the right rear side trim
panel.
PUSHPIN
(Pierce
TEMPLATE A 3 MARKS perpendicular.)
RIGHT REAR TEMPLATE A
SIDE TRIM
PANEL
4 of 13 AII04527-18 (1612) 2016 American Honda Motor Co., Inc. All Rights Reserved.
Without subwoofer 7. Using the printed lines as guides, fold the two tabs
on template B as shown.
6. Using a pushpin, pierce the right rear side trim panel
through template A as shown. Remove template A.
NOTE: There are several marks on template A. 2 TABS
(Fold.)
Before piercing the right rear side trim panel, verify
you have the correct locations. Make sure to pierce
the marks perpendicular to the right rear side trim
panel.
PUSHPIN
(Pierce
TEMPLATE A 2 MARKS perpendicular.)
(Do not use.)
2016 American Honda Motor Co., Inc. All Rights Reserved. AII04527-18 (1612) 5 of 13
8. Line up template B with the left rear side trim panel 9. Using a pushpin, pierce the left rear side trim panel
as shown. Tape template B to the left rear side trim through template B as shown. Remove template B.
panel with masking tape. NOTE: Make sure to pierce the marks perpendicular
to the left rear side trim panel.
Line up with the
Line up. curve end. Line up.
PUSHPIN
(Pierce
TEMPLATE B perpendicular.)
6 of 13 AII04527-18 (1612) 2016 American Honda Motor Co., Inc. All Rights Reserved.
10. Pull away the weatherstrip. Line up template C with 11. Using a pushpin, pierce the right rear side trim panel
the right rear side trim panel as shown. Tape through template C as shown. Remove template C.
template C to the right rear side trim panel with NOTE: Make sure to pierce the marks perpendicular
masking tape. to the right rear side trim panel.
TEMPLATE C MASKING
TAPE
RIGHT REAR
SIDE TRIM
PANEL
RIGHT REAR
TEMPLATE C SIDE TRIM
PANEL
2016 American Honda Motor Co., Inc. All Rights Reserved. AII04527-18 (1612) 7 of 13
14. Measure the location, and attach masking tape to 15. Measure the location, and attach masking tape to
the right rear side trim panel as shown. Using a the right rear side trim panel as shown. Using a
pushpin, pierce the right rear side trim panel as pushpin, pierce the right rear side trim panel as
shown. Remove the masking tape. shown. Remove the masking tape.
NOTE: Make sure to pierce the right rear side trim NOTE: Make sure to pierce the right rear side trim
panel perpendicular. panel perpendicular.
43 mm
(1.69 in.)
MARK
CURVE END 15 mm
(0.59 in.)
MARK RIGHT REAR
CARGO RIGHT REAR EDGE OF THE RIGHT SIDE TRIM
FLOOR LID SIDE TRIM REAR SIDE TRIM PANEL PANEL
PANEL
8 of 13 AII04527-18 (1612) 2016 American Honda Motor Co., Inc. All Rights Reserved.
If the vehicle is equipped with a subwoofer, continue 18. Install seven rivets into the seven holes on the right
with step 17; otherwise, go to step 19. rear side trim panel as shown. Go to step 21.
DRILL
(Drill
TAPE perpendicular.)
10 mm
(0.39 in.)
SECTION
RIVET VIEW
7 MARKS
3 mm
6 mm RIGHT REAR
DRILL BITS SIDE TRIM
Push in
PANEL further
than the
END OF THE end of
Push in the protruding the rivet.
portion using a flat-tip RIVET
screwdriver handle, etc. PROTRUDING
PORTION
RIGHT REAR
SIDE TRIM
PANEL
2016 American Honda Motor Co., Inc. All Rights Reserved. AII04527-18 (1612) 9 of 13
Without subwoofer 20. Install eight rivets into the eight holes on the right
rear side trim panel as shown.
19. While wearing eye protection, drill the eight pierced
marks on the right rear side trim panel to 6 mm. First
drill with a 3 mm drill bit, and finish with a 6 mm drill RIGHT REAR
8 RIVETS SIDE TRIM
bit. Remove any burrs. 8 HOLES PANEL
NOTE: Wrap tape around the 3 mm and 6 mm drill
bits 10 mm (0.39 in.) from the tip, or use a drill stop.
Make sure to drill perpendicular to the right rear side
trim panel.
DRILL
(Drill
TAPE perpendicular.)
10 mm
(0.39 in.)
8 MARKS SECTION
RIVET VIEW
3 mm
6 mm RIGHT REAR
DRILL BITS SIDE TRIM
PANEL
Push in
further
than the
Push in the protruding end of
END OF THE
portion using a flat-tip RIVET
the rivet.
screwdriver handle, etc.
PROTRUDING
PORTION
RIGHT REAR
SIDE TRIM
PANEL
10 of 13 AII04527-18 (1612) 2016 American Honda Motor Co., Inc. All Rights Reserved.
21. While wearing eye protection, drill the seven pierced 22. Install seven rivets into the seven holes on the left
marks on the left rear side trim panel to 6 mm. First rear side trim panel as shown.
drill with a 3 mm drill bit, and finish with a 6 mm drill
bit. Remove any burrs. LEFT REAR
NOTE: Wrap tape around the 3 mm and 6 mm drill SIDE TRIM 7 HOLES 7 RIVETS
PANEL
bits 10 mm (0.39 in.) from the tip, or use a drill stop.
Make sure to drill perpendicular to the left rear side
trim panel.
3 mm DRILL
6 mm (Drill
DRILL BITS perpendicular.)
10 mm
(0.39 in.)
7 MARKS
TAPE LEFT REAR
SIDE TRIM SECTION
RIVET VIEW
PANEL
END OF
Push in THE
PROTRUDING RIVET
PORTION further
than the
Push in the protruding end of
portion using a flat-tip the rivet.
screwdriver handle, etc.
23. Release the divider from the right rear side trim
panel.
DIVIDER
2016 American Honda Motor Co., Inc. All Rights Reserved. AII04527-18 (1612) 11 of 13
24. Fit the right cargo liner to the right rear side trim 27. Spread the center cargo liner on the cargo area.
panel as shown. Secure the right cargo liner to the Remove the headrests from the left and right rear
right rear side trim panel with eight hooks. Reinstall seat-backs, then install three loops on the center
the divider. cargo liner through the headrests as shown.
NOTE: Follow the same procedure if the vehicle is
equipped with a subwoofer. CENTER
HEADREST CARGO
GUIDE 3 HEADRESTS
KNOB LINER
RIGHT CARGO
LINER 8 HOOKS
Push.
3 LOOPS
RIGHT REAR
SEAT-BACK
DIVIDER
CENTER CARGO
CARGO FLOOR LINER
BOARD
(Raise.)
12 of 13 AII04527-18 (1612) 2016 American Honda Motor Co., Inc. All Rights Reserved.
USE AND CARE
To store the center cargo liner, secure the center cargo
liner to the left and right cargo liners with two fasteners,
or fold it under the cargo floor board.
2 FASTENERS
LEFT AND RIGHT
CARGO LINERS
BUMPER
COVER
CENTER CARGO
LINER
CENTER CARGO
LINER
(Fold under the
cargo floor board.)
2016 American Honda Motor Co., Inc. All Rights Reserved. AII04527-18 (1612) 13 of 13