Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Units system:SI
Current Date:4/24/2017 4:20 PM
Steel connections
Detailed report
__________________________________________________________________________________________________________________________
__________________________________________________________________________________
MEMBERS
Configuration
Exists opposite connection : No
Beam
General
Beam section : TW 185x6x8
Beam material : Q235
Beam initial height : 800 mm
Beam final height : 300 mm
Beam length : 6m
Vertical angle (deg) : 7
Include flange stiffener : No
Column
General
Support section : TW 185x6x8
Support material : Q235
Support initial depth : 800 mm
Support final depth : 300 mm
Support length : 8m
END PLATE
Connector
Plate extension : Extended external edge
Width : 200 mm
tp: Plate thickness : 20 mm
Plate material : Q235
Fy : 0.235 kN/mm2
Fu : 0.37 kN/mm2
Hole type on plate : Standard (STD)
Flush extension length : 20 mm
Plate alignment : Horizontal alignment
Weld
External flange weld type : Fillet
Page1
Weld to external flange : E43 Q235
D1: Weld size to external flange (1/16in) : 6
Internal flange weld type : Fillet
Weld to internal flange : E43 Q235
D3: Weld size to internal flange (1/16in) : 6
Web weld : E43 Q235
D2: Weld size to web (1/16in) : 6
Bolts
tp: Connection plate thickness : 20 mm
Bolts : M24 G88
g: Gage - transverse center-to-center spacing : 100 mm
Hole type : Standard (STD)
Lev: Vertical edge distance : 50 mm
Leh: Horizontal edge distance : 50 mm
Bolt group (external extension)
pfo t: Distance from bolt rows to flange : 50 mm
Bolt group (external flange)
Bolts rows number : 2
pfi t: Distance from bolt rows to flange : 50 mm
s t: Vertical spacing between inner bolt rows : 100 mm
Bolt group (internal flange)
Bolts rows number : 2
pfi b: Distance from bolt rows to flange : 50 mm
s b: Vertical spacing between inner bolt rows : 100 mm
STIFFENERS
Transverse stiffeners
Section : PL 1.2x8x77.2
Full depth : Yes
Length : 772 mm
bs: Transverse stiffeners width : 80 mm
cc: Corner clips : 20 mm
ts: Transverse stiffener thickness : 12 mm
Material : Q235
Weld type : Fillet
Welding electrode to support : E43 Q235
D: Weld size to support (1/16 in) : 6
DEMANDS
Beam Right beam Left beam Column Panel
Description Ru Pu Mu PufTop PufBot PufTop PufBot Pu Vu Load type
[KN] [KN] [KN*m] [KN] [KN] [KN] [KN] [KN] [KN]
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
DL -13.00 -24.00 101.00 -139.54 115.54 0.00 0.00 -16.00 117.54 Design
LL -18.00 -34.00 145.00 -200.10 166.10 0.00 0.00 -23.00 169.10 Design
D1 -13.00 -24.00 101.00 -139.54 115.54 0.00 0.00 -16.00 117.54 Design
D2 -31.00 -58.00 246.00 -339.64 281.64 0.00 0.00 -39.00 286.64 Design
D3 -26.50 -49.50 209.75 -289.61 240.11 0.00 0.00 -33.25 244.36 Design
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Page2
DG4 Sec. 2.4,
DG4 Sec. 2.1,
2.4,
DG16 Sec. 2.5
Outer bolt distance (external flange) [mm] 50.00 36.70 -- DG4 Sec. 2.1
Inner bolt distance (external flange) [mm] 50.00 36.70 -- DG4 Sec. 2.1
Inner bolt distance (internal flange) [mm] 50.00 36.70 -- DG4 Sec. 2.1
Bolt diameter [mm] 24.00 -- 38.10 DG4 Sec. 1.1
Support
Weld size (external flange) [1/16in] 6 3 -- table J2.4
Weld size (internal flange) [1/16in] 6 3 -- table J2.4
Web [1/16in] 6 2 -- table J2.4
Beam
Horizontal edge distance [mm] 50.00 41.65 152.40 Sec. J3.5
Support
Web thickness [mm] 6.00 6.74 -- p. 9-5
Transverse stiffeners
Length [mm] 772.00 380.00 -- Sec. J10.8
Width [mm] 80.00 63.67 -- Sec. J10.8
Thickness [mm] 12.00 10.00 -- Sec. J10.8
Weld size [1/16in] 6 5 -- DG 13 Eq. 4.3-6
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Page3
Bolt rupture with prying moment strength [KN*m] 506.66 0.00 DL 0.00 DG16 Sec 2.5
Support bolt bearing (external flange) [KN] 1278.72 31.00 D2 0.02 Eq. J3-6
Flexural yielding (internal flange) [KN*m] 312.83 223.03 D2 0.71 DG4 Eq. 3.20,
Sec. 2.2.3,
DG4 Eq. 3.21
Bolt rupture with prying moment strength [KN*m] 506.66 223.03 D2 0.44 DG16 Sec 2.5
Support bolt bearing (internal flange) [KN] 852.48 0.00 DL 0.00 Eq. J3-6
Panel web shear [KN] 301.75 288.31 D2 0.96 Sec. G1
Support - right side
Local web yielding [KN] 378.46 341.31 D2 0.90 DG4 eq. 3.24,
DG13 Eq. 4.3-1,
Sec. J10
Transverse stiffeners - bottom
Yielding strength due to axial load [KN] 202.63 104.14 D2 0.51 Eq. D2-1
Compression [KN] 73.27 0.00 DL 0.00 Sec. J4.4
Flange weld capacity [KN] 226.41 104.14 D2 0.46 Eq. J2-4
Web weld capacity [KN] 2132.02 104.14 D2 0.05 Eq. J2-4
Page4