Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1. Consider the equilibrium stage with C components shown below. Conduct a degree-of-
freedom analysis by performing the following steps: (a) list and count the variables; (b) write
and count the equations relating the variables; and (c) calculate the degree of freedom.
E q u ilib r iu m liq u id
fro m a n o th e r s ta g e E x it e q u ilib r iu m v a p o r
V , T V, P V, y i
Feed vapor
E q u ilib r iu m s ta g e E x it e q u ilib r iu m
liq u id p h a s e
F e e d liq u id L I , T L I , P L I , x iI
E q u ilib r iu m v a p o r E x it e q u ilib r iu m
fro m a n o th e r s ta g e liq u id p h a s e I I
Q
H e a t to L I I , T L I I , P L I I , x iI I
(+ ) o r fro m (-)
th e s ta g e
h V, V , T V, P V, y i
F la s h d r u m
L iq u id fe e d
h F, F, T F, P F, z i
h L, L , T L, P L, x i
V , T V, P V, y i
F la s h d r u m
Vapor
L iq u id f e e d
L iq u id I
L I, T L I, P L I, x I
F, T F, P F, z i i
L iq u id I I
L I I , T L I I , P L I I , x iI I
Air
n-hexane-rich liquid
Aniline-rich liquid
Water-rich liquid
Phosphorous liquid
Gallium liquid
Mercury liquid
Note: the following Matlab codes can plot the data using spline command:
T=[78.4 77.5 75 72.5 70 68.5 67.7 68.5 72.5 75 77.5 80.1];
y=[0 0.075 0.28 0.42 0.54 0.60 0.68 0.73 0.82 0.88 0.95 1.0];
x=[0 0.015 0.05 0.12 0.22 0.31 0.68 0.81 0.91 0.95 0.98 1.0];
ppx=spline(x,T);
ppy=spline(y,T);
xp=0:0.02:1;yp=xp;
Tx=ppval(ppx,xp);
Ty=ppval(ppy,yp);
plot(xp,Tx,yp,Ty)
grid on
Title('Txy data for benzene-ethyl alcohol at 1 atm')
xlabel('x,y: mole fraction benzene')
ylabel('T(^oC)')
Determine: (a) the temperature where vaporization begins; (b) the composition of the first
bubble of vapor; (c) the composition of the residual liquid when 25 mol% has evaporated,
assuming that all vapor formed is retained in the apparatus and is in equilibrium with the
residual liquid. (d) Repeat part (c) for 90 mol% vaporized. (e) Repeat part (d) if, after 25 mol
% is vaporized as in part (c), the vapor formed is removed and an additional 35 mol% is
vaporized by the same technique used in part (c).
Analysis: See plot of T-x-y data on next page, as drawn with a spreadsheet. Curved (instead
of straight) lines connecting the points would be a good improvement.
(a) For a benzene mole fraction of 0.25, a vertical line from M intersects the liquid
line at N at 69.4oC, which is the bubble point.
(b) The benzene mole fraction in the vapor at 69.4oC, obtained from the left-most
vapor line at P, is 0.56.
(c) To find the benzene mole fraction in the liquid at 25 mol% vaporization, extend a
dashed, vertical line upward from the bubble point at N, as shown in the figure on the next
page, until point B is reached. At this point, using the inverse lever-arm rule, the ratio of the
AB line length to the BC line length is 25/75. The benzene mole fraction in the equilibrium
liquid at point A is 0.175 at a temperature of 71.2oC.
(d) To find the benzene mole fraction in the liquid at 90 mol% vaporization, extend a dashed,
vertical line upward from the bubble point, as shown in the figure on the next page, until
point E is reached. At this point, using the inverse lever-arm rule, the ratio of the DE line
length
to the EF line length is 90/10. The benzene mole fraction in the equilibrium liquid at point D
is 0.045 at a temperature of 75.1oC.
(e) To find the benzene mole fraction in the liquid when the liquid from part (c) is
removed from the vapor and further vaporized, proceed as follows. If we start with 100
moles, then the liquid at 25 mol% vaporized is 75 moles with a benzene mole fraction of
0.17. If an additional 35 mol% is vaporized, we will have 35 moles of vapor in equilibrium
with 40 moles of liquid. Therefore, extend a dashed, vertical line upward from point A, as
shown in the figure on the next page, until point H is reached. At this point, using the inverse
lever-arm rule, the ratio of the GH line length to the HI line length is 35/40. The benzene
mole fraction in the liquid at G is 0.05 at a temperature of 74.9oC.
6.2 Stearic acid is steam distilled at 200oC in a direct-fired still. Steam is introduced into the
molten acid in small bubbles, and the acid in the vapor phase leaving the still has a partial
pressure equal to 70% of the vapor pressure of pure stearic acid at 200 oC. Use Matlab to plot
the kg acid distilled per kg steam added as a function of total pressure from 101.3 kPa to 3.3
kPa at 200oC. Label the plot with your name using the Title command. The vapor pressure
of stearic acid at 200oC is 0.40 kPa.
P, kPa kg A/kg B
101.3 0.0438
75 0.0592
50 0.0890
25 0.1790
15 0.3006
10 0.4553
5 0.9376
3.3 1.4650
7. The relative volatility, , of benzene to toluene at 1 atm is 2.5. Construct x-y and T- x-y
diagrams for this system at 1 atm. On the same diagrams, plot the data obtained using the
following vapor pressure data and ideal solution:
TA, TB = temperature of benzene and toluene at the given vapor pressure, respectively
P, torr 20 40 60 100 200 400 760 1,520
TA, OC 2.6 7.6 15.4 26.1 42.2 60.6 80.1
TB, OC 18.4 31.8 40.3 51.9 69.5 89.5 110.6 136
Use the diagram for the following: (a) A liquid containing 70 mol% benzene and 30 mol%
toluene is heated in a container at 1 atm until 25 mol% of the original liquid is evaporated.
Determine the temperature. The phases are then separated mechanically, and the vapors
condensed. Determine the composition of the condensed vapor and the liquid residue. (b)
Calculate and plot the K-values as a function of temperature at 1 atm.
Note: Use Matlab to plot the diagrams and label the figures with your name using the Title
command.
T, oC Ps of A, torr Ps of B, torr KA KB xA yA
(b) The Raoult's law K-values are included in the above table, and are plotted
below.
8. Saturated-liquid feed of F = 40 mol/h, containing 50 mol% A and B, is supplied to the
apparatus in the following figure.
Vapor
V
C ondenser
S till p o t
Feed
F R e flu x D is t illa te
R D
H eat
B o tto m s
W
The condensate is split so that reflux/condensate = 1. (a) If heat is supplied such that W = 30
mol/h and relative volatility = 2, what will be the composition of the overhead and the
bottoms product. (b) If the operation is changed so that no condensate is returned to the still
pot and W = 3D, compute the product compositions.
(b) Note that the solution to Part (a) was independent of the reflux ratio. Accordingly, the
solution to Part (b) is the same as for Part (a)