Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
AluminumPCB 1W/m*KAluminiumPCBfabrication
PCB Fabrication
Layer Count: 1L
PCB Prototype Board
Board Thickness: 1.6mm
130Layer FR4 PCB
Panel Dimension: 256*90mm/3up
Aluminum PCB
Material: Aluminum
HDI PCB
Copper on board surface: 35m
High Frequency PCB
Min Hole Dia*meter: 4.7mm
PCB Assembly Min line Width/Space: N/A
Medical
Computer
Car
Industrial Control
Security & Protection
Smart Home
Wearable Devices
Power
ProductDetails
Consumer Electronics
LED lighting
http://heroselectronics.com/en/AluminumPCB/209.html 1/4
2017328 1W/m*KAluminiumPCBfabricationAluminumPCBHerosElectronics
http://heroselectronics.com/en/AluminumPCB/209.html 2/4
2017328 1W/m*KAluminiumPCBfabricationAluminumPCBHerosElectronics
Industrial Equipment Highpower transistors, transistor arrays, pushpull or totem pole output circuit (to tem pole), solidstate relay,
pulse motor driver, the engine Computing amplifiers (Operational amplifier for serromotor), polechanging
device (Inverter)
Cars Car light, firing implement, power regulator, exchange converters, power controllers, variable optical system
Others Semiconductor thermal insulation board, IC arrays, resistor arrays, Ics carrier chip, heat sink, solar cell substrates,
semiconductor refrigeration device
1. There is side etching of Aluminum core PCB, factory must meet the accuracy of the trace so that need to do some trace
compensation when make working Gerber files, but compensation must be confirmed as per the value of side etched with different
MCPCB substrate thickness, the artwork is negative.
2. During the flow process of Aluminium PCB layer image, it usually use 0.3mm epoxy board, which the size is the same as the aluminium
PCB board, and use the tape to blockade and compaction to avoid solution infiltration. After the finish on copper surface, the best way
is to use the chemical micro etching, and then after board baking it should deal with wet film to prevent oxidation.
3. In the flow process of etching Aluminum PCB Board, need to use test boards to adjust the solution to ensure the best etching results.
After etching on Aluminum based PCB, the way is to use SN solution to do strip immediately. In the process of etching in Aluminium PCB,
need to use test boards to adjust the solution to ensure the best etching results.
4. Most of Aluminum PCB Manufacturers make the hole with diameter less than 6.0mm with NC drilling, but have to make the holes more
than 6.0mm with routing, which can not ensure the hole size 100% round. If there is strict requirement of round holes, they will ask make a
punching mould to make them more than 6.0mm.
5. Not like around 2008, nowadays more and more LED light designer and manufacturer has a demand of big Aluminum MCPCB or FR4,
like 1200mm or even to 1600mm. For such long Aluminum PCB, most Aluminum PCB suppliers cant provide since they havent big
enough equipment, like electroplate copper line, exposure machine, routing machine, related surface treatment line and routing
machine. As a professional PCB manufacturer, we can do it perfectly.
http://heroselectronics.com/en/AluminumPCB/209.html 3/4
2017328 1W/m*KAluminiumPCBfabricationAluminumPCBHerosElectronics
RecommendedProducts
Single Sided Bergquist Aluminum LED MCPCB IMS Aluminum PCB 1W/m*K Aluminium PCB Quick 2.5mm Aluminum PCB
PCB Manufacturer China Prototype with Fast Shipping fabrication Production MCPCB
Manufacturer
http://heroselectronics.com/en/AluminumPCB/209.html 4/4