Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
2.
Refer to the exhibit. On the basis of the information that is presented,
what additional configuration is required?
The ip address dhcp command is required on interface Fa0/0.
The ip dhcp information option command is required on interface Fa0/1.
The ip forward-protocol 37 command is required on interface Fa0/1 to forward
DNS requests to IP address 10.1.2.10.
The ip forward-protocol 67 command is required on interface Fa0/1 to forward
DHCP requests to IP address 10.1.2.10.
The ip forward-protocol 69 command is required on interface Fa0/1 to forward
TFTP requests to IP address 10.1.2.10.
The ip helper-address 10.1.2.10 command is required on interface Fa0/0.
3. In IS-IS routing, which level is used to route between end systems and
intermediate systems within the same area?
Note: Module not for cheating. this is use to practice for your course 1
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
level 0
level 1
level 2
level 3
4.
Given the above graphic, which command will perform interarea route
summarization?
RTA(config-router)# summary-address 200.9.0.0 255.255.0.0
RTB(config-router)# summary-address 192.168.16.0 255.255.252.0
RTB(config-router)# area 1 range 192.168.16.0 255.255.252.0
RTA(config-router)# area 1 range 200.9.0.0 255.255.0.0
6.
Observe the configuration. RTA has two serial links and an Ethernet stub
network of 3.1.0.0/16. Which command must the network administrator
use to have EIGRP summarize the stub network at the classful boundary?
RTA(config-router)# auto-summary 3.1.0.0 255.255.0.0
RTA(config-router)# IP auto-summary
Note: Module not for cheating. this is use to practice for your course 2
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
RTA(config-router)# no auto-summary
The network administrator does not have to issue a command.
7.
Given the above output from the show ip route command on RTA, which
two statements are true? (Choose two.)
This route has an administrative distance of 1 by default.
This route has an administrative distance of 5 by default.
This route has an administrative distance of 90 by default.
RTA is configured with route redistribution and the 2.1.0.0/16 network was
redistributed from another routing protocol.
RTA is configured with manual summarization of the 2.1.0.0/16 network on an
interface.
RTA is configured with a static route sending all traffic destined for the
2.1.0.0/16 network to the null0 interface.
8.
Refer to the exhibit. Which statement is correct about EIGRP
authentication?
Because the MD5 password does not match, Router A and Router B will not
exchange EIGRP routing tables.
Because the time period for which the key can be sent for key 1 does not
match, Router A and Router not exchange EIGRP routing tables.
Because a key chain is not associated with the interface, Router A and Router B
will not exchange EIGRP routing tables.
Router A and Router B will authenticate and exchange EIGRP routing tables.
Note: Module not for cheating. this is use to practice for your course 3
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
9. When running OSPF, which options must be the same within the hello
packet exchanged between two adjacent routers? (Choose three.)
stub flag
hello/dead intervals
router priority
DR/BDR assignments
area ID
12. An IS-IS Level 1 and Level 2 (L1L2) router has the characteristics of
which OSPF router?
backbone router
non-backbone router
ABR
ASBR
Note: Module not for cheating. this is use to practice for your course 4
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
carries upper layer data and error indications over connection-oriented links
carries lower layer data and error indications over connectionless links
14.
Refer to the exhibit. Two-way redistribution was configured between
OSPF and RIP on R2. After the redistribution, R3 does not see any
external routes coming from the RIP domain. The debug ip ospf database
external output reveals that no external LSAs are generated for the
routes. What could the problem be?
A default-metric command is missing from the R2 configuration.
A subnet keyword is missing from the R2 configuration.
An area 0 stub command is missing from the R2 configuration.
A distribute-list in Serial0/1 command on R3 is blocking all of the updates
coming from R2.
Note: Module not for cheating. this is use to practice for your course 5
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
IGMP uses the unicast routing information to perform the multicast forwarding
function.
18. What is the default priority value for all OSPF routers?
Priority 0
Priority 1
Priority 8
Priority 10
Priority 255
Note: Module not for cheating. this is use to practice for your course 6
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
20.
Based on the information in the diagram, which configuration is needed
to redistribute RIP into OSPF?
RTA(config)# router rip
RTA(config-router)# redistribute ospf 10 metric 25 bandwidth
RTA(config)# router rip
RTA(config-router)# redistribute ospf metric 2
RTA(config)# router ospf 10
RTA(config-router)# redistribute rip metric 25
RTA(config)# router ospf 10
RTA(config-router)# redistribute rip metric 10000 100 255 1 1500
21.
Refer to the configurations shown in the graphic. R1 and R2 are unable
to establish a BGP peer relationship. After a network administrator has
confirmed that each router can ping the loopback interface of the other
router, what can be done to fix this problem?
add a BGP network command for 4.1.1.0/24 on both routers
Note: Module not for cheating. this is use to practice for your course 7
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
add the BGP no synchronization command on both routers
add the BGP neighbor update-source serial0 command on both routers
add the BGP neighbor ebgp-multihop 255 command on both routers
22.
Observe the configuration. The EIGRP subnets such as 10.10.0.0/16 and
10.20.0.0/16 are not being seen inside the OSPF domain. What is a
possible reason for this?
The redistribute command is missing the subnets keyword in the OSPF
configuration.
The redistribute command is missing the subnets keyword in the EIGRP
configuration.
The network statement is wrong in the EIGRP configuration.
The metric value is incorrect for EIGRP.
The metric value is incorrect for OSPF.
Note: Module not for cheating. this is use to practice for your course 8
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
24. Which statement is true regarding creating a multicast MAC address
from a MAC address and an IP address?
The first 24 bits of the IP multicast address are used for the first 24 bits of the
multicast MAC address.
The first 24 bits of the IP multicast address are used for the last 24 bits of the
multicast MAC address.
The last 23 bits of the IP multicast address are used for the first 23 bits of the
multicast MAC address.
The last 23 bits of the IP multicast address are used for the last 23 bits of the
multicast MAC address.
The 32 bits of the IP multicast address are used for the first 32 bits of the
multicast MAC address.
25.
A network administrator recently redistributed RIP routes into the OSPF
network and would like to reduce the size of the routing table. Given the
above graphic, which command would create an external summarization
of all the RIP routes?
summary-address 200.9.0.0 255.255.0.0
summary-address 200.9.0.0 0.0.255.255
area 0 range 200.9.0.0 255.255.0.0
area 0 range 200.9.0.0 0.0.255.255
area 1 range 200.9.0.0 255.255.0.0
27. Which of the following is a network service that is used to reduce the
task of allocating IP addresses?
Note: Module not for cheating. this is use to practice for your course 9
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
DHCP
PAT
NAT
DNS
28.
A network administrator has recently added a new area, Area 3, to the
OSPF internetwork. Due to physical limitations, it is not possible to
provide Area 3 with direct access to the backbone. What must the
administrator configure to ensure continuity in the OSPF network?
area area-id stub no-summary
neighbor
area area-id nssa no-summary
area area-id virtual-link router-id
30. What is the IPv6 loopback address a technician would ping to verify the
IPv6 stack is loaded?
Note: Module not for cheating. this is use to practice for your course 10
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
0::127:0:0:1
0::7f00:1
FE80::1
FE80::7f00:1
::1*
0::7f:0:0:1
31.
Refer to the exhibit. Host A is unable to obtain an IP address from the
DHCP server. Which procedure would solve this problem?
Configure ip helper-address 10.1.2.1 on interface Fa0/0 of router RTA.
Configure ip helper-address 10.1.2.10 on interface Fa0/0 of router RTA.
Configure ip helper-address 10.1.2.10 on interface Fa0/1 of router RTA.
Configure ip forward-protocol 67 on interface Fa0/0 of router RTA.
Configure ip forward-protocol 68 on interface Fa0/1 of router RTA.
Configure ip forward-protocol 67 on interface Fa0/1 of router RTA.
32. What happens to packets that do not meet any of the defined match
criteria of a route map?
They are dropped.
They are flagged as undeliverable.
They are routed using the default route.
They are routed through the normal routing process for forwarding.
Note: Module not for cheating. this is use to practice for your course 11
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
34. How many bits make up an IPv6 address?
32
48
64
128
36. Which attribute must be sent in the BGP update packet and must be
recognized by all implementations of BGP?
well-known discretionary
optional non-transitive
well-known mandatory*
optional transitive
37. Based on the configuration below, which of the following statements are
true? RTA(config)# router bgp 100
RTA(config-router)# neighbor 190.10.50.1 remote-as 100
RTA(config-router)# neighbor 170.10.20.2 remote-as 300
RTA(config-router)# network 150.10.0.0
RTA is going to advertise network 150.10.0.0 to its neighbors if it is in the IP
routing table.*
The neighbor at 190.10.50.1 is an external peer.
The neighbor at 170.10.20.2 is an internal peer.
RTA is going to advertise that it is part of AS 300.
38. Which three statements about the similarities between OSPFv2 and
OSPFv3 are true? (Choose three.)
LSA flooding and aging are the same.*
Neighbor discovery and adjacency formation are the same.*
Hello, DBD, LSR, LSU packet types are similar.*
Note: Module not for cheating. this is use to practice for your course 12
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
Multicast addresses are the same.
Authentication between OSPF enabled routers uses the same protocols.
The router ID in OSPFv3 is also expressed in the same 16-bit format as OSPFv2.
39.
Refer to the exhibit. What is the result of the ip pim send-rp-announce
Loopback0 scope 3 group-list 50 command that is shown in the
configuration?
The router sends Auto-RP messages to address 224.0.1.39 announcing itself as
an RP candidate for multicast group 3.
The router sends Auto-RP messages to address 224.0.1.40 announcing itself as
an RP candidate for multicast group 3.
The router sends Auto-RP messages to address 224.0.1.39 announcing itself as
an RP candidate for multicast groups identified by access-list 50.
The router sends Auto-RP messages to address 224.0.1.40 announcing itself as
an RP candidate for multicast groups identified by access list 50.
The router sends RP-to-group mapping messages to address 224.0.1.39
announcing itself as an RP candidate for multicast group 3.
The router sends RP-to-group mapping messages to address 224.0.1.39
announcing itself as an RP candidate for multicast groups identified by access-
list 50.
Note: Module not for cheating. this is use to practice for your course 13
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
40.
Refer to the diagram. Which state is RTB in if it sees itself in the RTA
hello but no routing information has been exchanged?
init state
two-way state
exstart state
exchange state
loading state
41.
Refer to the exhibit. Router-A and Router-B are not forming an EIGRP
neighbor relationship. What is the reason?
AS number mismatch
incorrect route redistribution
K-values mismatch*
stuck-in-active
42. Which three items are contained in a BGP update message? (Choose
three.)
route prefix*
AS path*
weight
prefix length*
local preference
Note: Module not for cheating. this is use to practice for your course 14
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
43.
Which statement best describes routing of packets to the 10.1.4.0
network as displayed in the graphic of the EIGRP topology table entry?
equal-cost load balancing using interface Serial0 and Ethernet1
unequal-cost load balancing using interface Serial0 and Ethernet1
equal-cost load balancing using interface Serial0 and Ethernet0
no load balancing on interface Serial0 and Ethernet1
45. In which state does BGP start exchanging update packets with its peers?
connect
established
update
active
47. Which two OSPFv3 configuration statements are true? (Choose two.)
The command ipv6 ospf 1 area 0 must be given under router configuration
mode.
The ipv6 ospf 100 area 0 interface configuration command dynamically
creates the ipv6 router ospf 100 process.
The network router configuration command is required to enable OSPFv3 on
an interface.
Note: Module not for cheating. this is use to practice for your course 15
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
The OSPF cost is configured on the interface.
The OSPF router ID is configured on the interface.
The router priority is configured in router configuration mode.
50.
Refer to the exhibit. Router RTA and router RTB have been configured to
exchange routing information using OSPF. However, both routers never
transition beyond 2WAY state. What is the cause of this problem?
Note: Module not for cheating. this is use to practice for your course 16
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
An access list on one side is blocking OSPF Hellos.
Authentication is enabled on only one side.
There is a switch problem and multicast capabilities are broken.
The RTA and RTB interfaces have been configured with a priority of 0.
There is a misconfigured neighbor statement on RTA.
There is a misconfigured neighbor statement on RTB.
51. Support for which three items was added to IGMP Version 3? (Choose
three.)
input queue scheduling
specific group leave messages
multiple group membership
output queue scheduling
passive interfaces
source filtering
52. Which technique effectively insulates other routers from the problem of
route flapping?
route summarization
network address translation
IPv6
helper addresses
54. By default, if an IGP has not learned about a local route, BGP cannot
advertise it. Which configuration parameter will override this behavior?
ebgp-mulithop
no synchronization
remote-as
next-hop-self
Note: Module not for cheating. this is use to practice for your course 17
Take Assessment - CCNP-Building Scalable Internetworks
Final (Version 5.0)
55. Of the five EIGRP parameters, bandwidth, delay, reliability, load, and
MTU, which are used by default in determining the best path?
bandwidth, delay, reliability
bandwidth, load, reliability
bandwidth, reliability, delay
bandwidth, delay
bandwidth, load
56.
Observe the graphic and configuration. What must the administrator do
to ensure that clients within the 2.1.1.0/24 network will be able to
communicate with clients within the 2.0.0.0/8 network?
configure summarization on R1 with the ip summary-address eigrp command
disable automatic summarization on R1 with the no auto-summary command*
add the network 2.1.1.0 mask 255.255.255.0 command under router eigrp 100
enable classless support on R1 with the ip classless command
nothing, EIGRP supports discontiguous subnets by default
57. Which is a difference between the IS-IS and OSPF routing protocols?
the use of hello packets to form and maintain adjacencies
the DR and BDR election process
the use of link-state databases and Dijkstra's algorithm
the update, decision and flooding process
Note: Module not for cheating. this is use to practice for your course 18