Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Flanges
The STAUFF range of flanges gives you extensive product STAUFF SAE flanges are made of high-quality materials. Index G2
diversity, whether it is the DIN ISO 6162-1/2:2006 range or The exact steel quality and the surface treatment are adapted
SAEJ518 C compliant SAE flanges, as well as the range of individually to the needs and requirements of the flange.
SAE Flanges G4
gear pump flanges. Naturally, all our coated parts have CrVI-free surfaces.
Stainless steel (1.4404/1.4571), alternate gasket materials
The standard pressure series of STAUFF SAE flanges contains and higher bolt strengths are also available on request. Gear Pump Flanges G62
components for a flange connection with maximum operating
pressures from 35 ... 350 bar / 507 ... 5076 PSI. The STAUFF range of gear pump flanges is used as a
They are available in all nominal sizes between DN13 (1/2") supplement for gear-type rotary pumps, motors, and other
and DN127 (5"). smaller size pumps. We offer you a wide range of different
STAUFF covers maximum operating pressures of up to variations, divided into various sizes and designs, like, for
420 bar / 6092 PSI and nominal sizes between DN13 (1/2") example, a straight or 90 design with 3-hole or 4-hole
and DN51 (2") with this high-pressure series. fastening. It goes without saying that we manufacture our
pump flanges from high-quality materials, and naturally they
STAUFF SAE flanges are available as individual flanges also have CrVI-free surfaces.
without any accessories, or as complete components with
gaskets and suitable sets of bolts. A large number of different
Please do not hesitate to contact STAUFF.
components are available at all times.
www.stauff.com
Flanges
G
SAE Flanges
SAE Single-Part Screw-in BSPP
SAE Split Flange Halves DB G4 Threaded Flange BFX-G / BAS-G G18
and Counterflange
G2 www.stauff.com
SAE Block
BF-L G54 4-hole Butt Weld Flange GP-LK...-ST.../...#K G70
L-Connection (Adapter Style)
Accessories G57
The pressure information (maximum working pressures) stated in this catalogue All information apply to a temperature range of
only apply to the single components mentioned. It does not apply to the used bolts,
fittings, welded or screwed connections. Please take notice of the information and -20 C ... +90 C / -4 F ... +194 F
G
specification of the manufaturers for all further components used and also the legal
regulations. Outside of this temperature range, the material-specific properties could be reduced.
This applies to the selection of the sealing materials in particular.
Please note: The pressure information of the components of flange combinations
(consisiting of the flange itself and a tube end) may vary from each other. Please
consider the lowest pressure as the maximum working pressure of this combination.
www.stauff.com G3
G
I
(packed in kits)
**Including Metric bolts 10.9, DB-...-MH-B#K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
C 1
D
**Including UNC bolts (Gr8), DB-...-U-B#K
spring rings, O-ring made of NBR (Buna-N)
H
(packed in kits)
E F
Material S355J0 / C45 or equivalent
Surface CrVI-free
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
Dimensions of screw holes in part different to the ISO to match both Metric and UNC screws.
G4 www.stauff.com
G
I
(packed in kits)
**Including Metric bolts 10.9, BM-...-MH-B#K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits) C
**Including UNC bolts (Gr8), BM-...-U-B#K
spring rings, O-ring made of NBR (Buna-N) D H
(packed in kits) E F
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
Dimensions of screw holes in part different to the ISO to match both Metric and UNC screws.
Flanges
G
www.stauff.com G5
Order Codes
R
S
G
I
(packed in kits)
**including Metric bolts 10.9, DB-FL-...-MH-B#K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
C 1
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
Dimensions of screw holes in part different to the ISO to match both Metric and UNC screws.
G6 www.stauff.com
Order Codes
R
S
G
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
**including UNC bolts (Gr8), BM-FL-...-U-B#K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits) C
H
D
F
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
Dimensions of screw holes in part different to the ISO to match both Metric and UNC screws.
Flanges
G
www.stauff.com G7
R
S
**deviant Metric tapped holes (M14) BM-G-...M14
G
I
C
D H
E F
1
The maximum working pressure applies PN (bar) only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
Alternative options shown in brackets are available on request.
G8 www.stauff.com
Flanges
G
www.stauff.com G9
SAE Butt Weld Flange Adapter / SAE Butt Weld Counterflange Adapter
CAG/CSG-ST
Order Codes
L **SAE Butt Weld Flange Adapter
(without O-ring)
CAG-...-ST- /
A
C
D
(packed in kits)
**including Metric bolts 10.9, CAG-...-ST- / -MH#K
spring rings, O-ring made of NBR (Buna-N) and DB
(packed in kits)
CAG CSG
**including Metric bolts 8.8, CAG-...-ST- / -BM#K
spring rings, O-ring made of NBR (Buna-N) and BM
Material S355J0 or equivalent (packed in kits)
Surface blank, oiled / Please indicate pipe-OD and pipe-ID
Special Material Stainless Steel 1.4571 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
According to ISO 6162-2 bolts M12 should be used but because usually bolts M14 are used the description of the complete part must show M14 (e.g. CAG-604-ST- / -M14#K).
G10 www.stauff.com
SAE Socket Weld Flange Adapter / SAE Socket Weld Counterflange Adapter
CAG/CSG-ES
L
M
Order Codes
A
**SAE Socket Weld Flange Adapter CAG-...-ES-...
D
E
(without O-ring)
**SAE Socket Weld
Counterflange Adapter
CSG-...-ES-...
A
D
E
**including UNC bolts (Gr8), CAG-...-ES-...-V-U#K
spring rings, O-ring made of FPM (Viton) and DB Material S355J0 or equivalent
(packed in kits) Surface blank, oiled
Special Material Stainless Steel 1.4571 -W5 on request
Version B (CAG / CSG)
1
The maximum working pressure applies PN (bar) only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
www.stauff.com G11
L Order Codes
D
A
**Deviant BSPT Thread CAG-...-BSPT
***
T
**including Metric bolts 8.8, CAG-...-BSPT#K
spring rings, O-ring made of NBR (Buna-N) and DB
(packed in kits)
WAF
CAG CSG
**including Metric bolts 10.9, CAG-...-BSPT-MH#K
spring rings, O-ring made of NBR (Buna-N) and DB
(packed in kits)
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
G12 www.stauff.com
Order Codes L
D
A
**Deviant NPT Thread CAG-...-NPT
***
T
**including Metric bolts 8.8, CAG-...-NPT#K
spring rings, O-ring made of NBR (Buna-N) and DB
(packed in kits)
WAF
**including Metric bolts 10.9, CAG-...-NPT-MH#K
spring rings, O-ring made of NBR (Buna-N) and DB CAG CSG
(packed in kits)
**Including UNC bolts (Gr8), CAG-...-NPT-V-U#K
spring rings, O-ring made of FPM (Viton) and DB Material S355J0 or equivalent
(packed in kits) Surface CrVI-free
Special Material Stainless Steel 1.4571 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
Flanges
G
www.stauff.com G13
SAE Flange Adapter with 24 Cone Connector (acc. to ISO 8434-1 / DIN 2353)
CAG-L/S
Order Codes
L
**SAE Flange Adapter with 24 Cone Connector
(acc. to ISO 8434-1 / DIN 2353)
CAG-...
12
(without O-ring)
** including Metric bolts 8.8, CAG-...#K
spring rings, O-ring made of NBR (Buna-N) and DB
D
A
T
(packed in kits)
** including Metric bolts 10.9, CAG-...-MH#K
spring rings, O-ring made of NBR (Buna-N) and DB
WAF (packed in kits)
** including UNC bolts (Gr8), CAG-...-V-U#K
spring rings, O-ring made of FPM (Viton) and DB
Material S355J0 or equivalent (packed in kits)
Surface CrVI-free
Special Material Stainless Steel 1.4571 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
According to ISO 6162-2 bolts M12 should be used but because usually bolts M14 are used the description of the complete part must show M14 (e.g. CAG-604-S30-M14#K).
G14 www.stauff.com
L
Order Codes
D
(without O-ring)
A
**including Metric bolts 8.8, spring CAG90-...-ST-...#K
rings, O-ring made of NBR (Buna-N) and DB
(packed in kits)
M
**including Metric bolts 10.9, CAG90-...-ST-...-MH#K
spring rings, O-ring made of NBR (Buna-N) and DB
(packed in kits)
**including UNC bolts (Gr8), CAG90-...-ST-...-V-U#K
spring rings, O-ring made of FPM (Viton) and DB A B
(packed in kits)
Material S355J0 or equivalent
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
According to ISO 6162-2 bolts M12 should be used but because usually bolts M14 are used the description of the complete part must show M14 (CAG90-604-ST-30/22-M14#K).
www.stauff.com G15
L
A Order Codes
D
(without O-ring)
** including Metric bolts 8.8, CAG90-...#K
spring rings, O-ring made of NBR (Buna-N) and DB
M
(packed in kits)
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
According to ISO 6162-2 bolts M12 should be used but because usually bolts M14 are used the description of the complete part must show M14 (e.g. CAG90-604-S30-M14#K).
G16 www.stauff.com
Flanges
G
www.stauff.com G17
L F Order Codes
H
Bolt
M
**BSPP
SAE Single-Part Screw-in
Threaded Flange (without O-ring)
BFX-...-G
A
T
G
I
**deviant Screw-in BSPP thread, BFX-...-G
including Metric bolts 10.9, spring rings,
*** -MH#K
D
**including UNC bolts (Gr8), BFX-...-G-V-U#K
spring rings, O-ring made of FPM (Viton)
K
(packed in kits)
Material S355J0 or equivalent
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
350 400 25 1 BFX-603-G034 19 24,5 68 82 27,8 57,2 44 18 3/4 13 M12x45 7/1614 UNC x 1-3/4 2
350 400 32 1-1/4 BFX-604-G 31 27,5 79 95 31,6 66,6 44 22 1-1/4 13,5 M12x45 1/213 UNC x 1-3/4
350 400 32 1-1/4 BFX-604-G-M14 31 27,5 79 95 31,6 66,6 44 22 1-1/4 15 M14x45
350 400 32 1-1/4 BFX-604-G100 25 27,5 79 95 31,6 66,6 44 20 1 13,5 M12x45 1/213 UNC x 1-3/4
350 400 32 1-1/4 BFX-604-G100-M14 25 27,5 79 95 31,6 66,6 44 20 1 15 M14x45
350 400 38 1-1/2 BFX-605-G 38 31 88 108 36,5 79,3 51 24 1-1/2 17 M16x55 5/811 UNC x 2-1/4
350 400 38 1-1/2 BFX-605-G114 31 31 88 108 36,5 79,3 51 22 1-1/4 17 M16x55 5/811 UNC x 2-1/4
350 400 51 2 BFX-606-G 50 37 118 137 44,5 96,8 65 33 2 21 M20x70 3/410 UNC x 2-3/4
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
For UNC threaded bolts, use hexagon head bolts only. Please note that these do not belong to our product range.
3
Alternative options shown in brackets are available on request.
G18 www.stauff.com
Order Codes L
Thread
M
**SAE Single-Part Screw-in
BSPP Threaded Counterflange
BAS-...-G
A
**For deviant Metric bolts (M14), BAS-...-GM14-100
G
I
deviant Screw-in BSPP thread
D H
F
Material S355J0 or equivalent
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
350 400 51 2 BAS-606-G 50 37 118 137 44,5 96,8 58 33 2 M20 3/410 UNC
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
G
www.stauff.com G19
F
L
H
Order Codes
M
Bolt
**NPT
SAE Single-Part Screw-in
Threaded Flange (without O-ring)
BFX-...-N
A
O-ring made of NBR (Buna-N)
G
I
(packed in kits)
**deviant Screw-in NPT thread, BFX-...-N
including Metric bolts 10.9, spring rings,
*** -MH#K
350 400 25 1 BFX-603-N034 19 24,5 68 82 27,8 57,2 44 18 3/4 13 M12x45 7/1614 UNC x 1-3/4 2
350 400 32 1-1/4 BFX-604-N 31 27,5 79 95 31,6 66,6 44 22 1-1/4 13,5 M12x45 1/213 UNC x 1-3/4
350 400 32 1-1/4 BFX-604-N-M14 31 27,5 79 95 31,6 66,6 44 22 1-1/4 15 M14x45
350 400 32 1-1/4 BFX-604-N100 25 27,5 79 95 31,6 66,6 44 20 1 13,5 M12x45 1/213 UNC x 1-3/4
350 400 32 1-1/4 BFX-604-N100-M14 25 27,5 79 95 31,6 66,6 44 20 1 15 M14x45
350 400 38 1-1/2 BFX-605-N 38 31 88 108 36,5 79,3 51 24 1-1/2 17 M16x55 5/811 UNC x 2-1/4
350 400 38 1-1/2 BFX-605-N114 31 31 88 108 36,5 79,3 51 22 1-1/4 17 M16x55 5/811 UNC x 2-1/4
350 400 51 2 BFX-606-N 50 37 118 137 44,5 96,8 65 33 2 21 M20x70 3/410 UNC x 2-3/4
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
For UNC threaded bolts, use hexagon head bolts only. Please note that these do not belong to our product range.
3
Alternative options shown in brackets are available on request.
G20 www.stauff.com
Order Codes L
Thread
M
G
I
**For
deviant Screw-in NPT thread
BAS-...-NM14-100
D H
F
Material S355J0 or equivalent
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
350 400 51 2 BAS-606-N 50 37 118 137 44,5 96,8 58 33 2 M20 3/410 UNC
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
G
www.stauff.com G21
L F Order Codes
M H
**SAE Single-Part Screw-in BFX-...-U
**
Bolt
UN Threaded Flange (without O-ring)
**including Metric bolts 8.8,
**
BFX-...-U #K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
G
**including Metric bolts 10.9,
**
BFX-...-U -MH#K
I
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
**including UNC bolts (Gr8),
**
BFX-...-U -V-U#K
spring rings, O-ring made of FPM (Viton)
D K
(packed in kits)
Material S355J0 or equivalent
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
350 400 25 1 BFX-603-U1-5/16 25 24,5 68 82 27,8 57,1 44 19 1-5/1612 13 M12x45 7/1614 UNC x 1-3/4 2
350 400 32 1-1/4 BFX-604-U1-5/16 31 27,5 79 95 31,6 66,7 44 19 1-5/1612 13,5 1/213 UNC x 1-3/4
350 400 32 1-1/4 BFX-604-U1-5/16-M14 31 27,5 79 95 31,6 66,7 44 19 1-5/1612 15 M14x45
350 400 32 1-1/4 BFX-604-U1-5/8 31 27,5 79 95 31,6 66,7 44 19 1-5/812 13,5 1/213 UNC x 1-3/4
350 400 32 1-1/4 BFX-604-U1-5/8-M14 31 27,5 79 95 31,6 66,7 44 19 1-5/812 15 M14x45
350 400 38 1-1/2 BFX-605-U1-5/8 38 31 88 108 36,5 79,4 51 19 1-5/812 17 M16x55 5/811 UNC x 2-1/4
350 400 38 1-1/2 BFX-605-U1-7/8 38 31 88 108 36,5 79,4 51 19 1-7/812 17 M16x55 5/811 UNC x 2-1/4
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
For UNC threaded bolts, use hexagon head bolts only. Please note that these do not belong to our product range.
3
Alternative options shown in brackets are available on request.
G22 www.stauff.com
Order Codes L F
M H
**SAE Single-Part Screw-in BFX-...-M
**
Bolt
Metric Threaded Flange (without O-ring)
**including Metric bolts 8.8,
**
BFX-...-M #K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
A
**including Metric bolts 10.9, BFX-...-M
**-MH#K
G
I
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
D K
Material S355J0 or equivalent
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
3
Alternative options shown in brackets are available on request.
Flanges
G
www.stauff.com G23
SAE Single-Part Butt Weld Flange for High Pressure Tubes (Schedule 80/160/XXS)
BFX-ST
F Order Codes
L H
**SAE Single-Part Butt Weld Flange BFX-...-ST-
**/**
Bolt
(without O-ring)
**including Metric bolts 8.8,
** **
BFX-...-ST- / #K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
G
I
** ** **
including Metric bolts 10.9, BFX-...-ST- / -MH#K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
D K
** ** **
including UNC bolts (Gr8), BFX-...-ST- / -V-U#K
spring rings, O-ring made of FPM (Viton)
(packed in kits)
Material S355J0 or equivalent
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
For UNC threaded bolts, use hexagon head bolts only. Please note that these do not belong to our product range.
3
Alternative options shown in brackets are available on request.
G24 www.stauff.com
SAE Single-Part Butt Weld Counterflange for High Pressure Tubes (Schedule 80/160/XXS)
BAS-ST
A
B
G
I
D H
F
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
3
Alternative options shown in brackets are available on request.
Flanges
G
www.stauff.com G25
SAE Single-Part Butt Weld Flange for Low Pressure Tubes (Schedule 40)
BFX-STRE
F
L H
Order Codes
Bolt
**SAE Single-Part Butt Weld
Flange (without O-ring)
BFX-...-STRE-
**/**
**including ** **
Metric bolts 8.8, BFX-...-STRE- / #K
spring rings, O-ring made of NBR (Buna-N)
A1
B
A
(packed in kits)
G
I
** ** **
incl. Metric bolts 10.9, BFX-...-STRE- / -MH#K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
D K ** ** **
incl. UNC bolts (Gr8), BFX-...-STRE- / -V-U#K
spring rings, O-ring made of FPM (Viton)
(packed in kits)
Material S355J0 or equivalent
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
3
Alternative options shown in brackets are available on request.
G26 www.stauff.com
SAE Single-Part Butt Weld Counterflange for Low Pressure Tubes (Schedule 40)
BAS-STRE
A1
B
G
I
D H
F
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
3
Alternative options shown in brackets are available on request.
Flanges
G
www.stauff.com G27
F Order Codes
L H
**SAE Single-Part Butt Weld BFX-...-SRE-
**/**
Bolt
Flange (without O-ring)
**including Metric bolts 8.8,
** **
BFX-...-SRE- / #K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
A1
B
** ** **
incl. Metric bolts 10.9, BFX-...-SRE- / -MH#K
G
I
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
** incl. UNC bolts (Gr8),
** **
BFX-...-SRE- / -V-U#K
spring rings, O-ring made of FPM (Viton)
D K
(packed in kits)
Material S355J0 or equivalent
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
For UNC threaded bolts, use hexagon head bolts only. Please note that these do not belong to our product range.
3
Alternative options shown in brackets are available on request.
G28 www.stauff.com
A1
B
G
I
D H
F
Material S355J0 or equivalent
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
Flanges
www.stauff.com G29
L F Order Codes
M H
Bolt
**SAE Single-Part Socket Weld
Flange (without O-ring)
BFX-...-ES-
**/**
**including Metric bolts 8.8,
** **
BFX-...-ES- / #K
spring rings, O-ring made of NBR (Buna-N)
G
I
(packed in kits)
** incl. Metric bolts 10.9,
** **
BFX-...-ES- / -MH#K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
D K ** ** **
including UNC bolts (Gr8), BFX-...-ES- / -V-U#K
spring rings, O-ring made of FPM (Viton)
(packed in kits)
Material S355J0 or equivalent
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
For UNC threaded bolts, use hexagon head bolts only. Please note that these do not belong to our product range.
3
Alternative options shown in brackets are available on request.
G30 www.stauff.com
L
Order Codes M Thread
B
** ** **
For deviant Metric bolts (M14) BAS-...-ESM14- /
G
I
D H
F
350 400 64 2-1/2 BAS-607-ES-76,6/63 63 76,6 45 152 180 58,7 123,8 80 32 M24
350 400 76 3 BAS-608-ES-90,5/73 73 90,5 55 178 208 71,4 152,4 90 30 M30
G
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
3
Alternative options shown in brackets are available on request.
www.stauff.com G31
F
M H
Order Codes
Bolt
**SAE ** **
Single-Part Socket Weld BFX-FL-...-ES- /
Flange (Flat Style) (without O-ring)
**including ** **
Metric bolts 8.8, BFX-FL-...-ES- / #K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
G
I
D K
1
The maximum working pressure PN (bar) applies only to the flange itself. The actual maximum working pressure depends on the thickness and the quality of the tube used.
G32 www.stauff.com
G
I
D H
F
1
The maximum working pressure PN (bar) applies only to the flange itself. The actual maximum working pressure depends on the thickness and the quality of the tube used.
Flanges
G
www.stauff.com G33
SAE Single-Part Fitting Flange with 24 Cone Connector (acc. to ISO 8434-1 / DIN 2353)
BFX-L/S
F
Order Codes
L H
Bolt
**SAE Single-Part Fitting Flange BFX-...-L
**/-S**
12
(without O-ring)
**including Metric bolts 8.8,
**
BFX-...-L #K
spring rings, O-ring made of NBR (Buna-N)
B
(packed in kits)
G
A
T
I
**including Metric bolts 10.9, BFX-...-L
spring rings, O-ring made of NBR (Buna-N)
**-MH#K
(packed in kits)
D K
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
3
Alternative options shown in brackets are available on request.
G34 www.stauff.com
SAE Single-Part Fitting Flange with BSP 60 Cone Connector (acc. to BS 5200)
BFX-B
Order Codes F
L H
Bolt
**SAE Single-Part Fitting Flange
(without O-ring)
BFX-...-B
6 0
**spring rings, O-ring made of NBR (Buna-N)
including Metric bolts 8.8, BFX-...-B#K
G
T
I
(packed in kits)
**including Metric bolts 10.9, BFX-...-B-MH#K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
D K
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
3
Alternative options shown in brackets are available on request.
www.stauff.com G35
SAE Single-Part Fitting Flange with JIC 37 Cone Connector (acc.to ISO 8434-2 / SAE J514)
BFX-J
F
L
Order Codes
H
Bolt
**SAE Single-Part Fitting Flange
(without O-ring)
BFX-...-J
**
**including Metric bolts 8.8,
**
BFX-...-J #K
37
spring rings, O-ring made of NBR (Buna-N)
A
(packed in kits)
G
T
I
**including Metric bolts 10.9,
**
BFX-...-J -MH#K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
D K **including UNC bolts (Gr8),
spring rings, O-ring made of FPM (Viton)
**
BFX-...-J -V-U#K
(packed in kits)
Material S355J0 / C45 or equivalent
Surface CrVI-free
Special Material Stainless Steel 1.4404 -W5 on request
350 400 32 1-1/4 BFX-604-J1-5/16 21,5 24 75 95 31,6 66,6 64 1-5/1612 13,5 M12x45 1/213 UNC x 1-3/4
350 400 32 1-1/4 BFX-604-J1-5/16-M14 21,5 24 75 95 31,6 66,6 64 1-5/1612 15 M14x45
350 400 32 1-1/4 BFX-604-J1-5/8 27,5 24 75 95 31,6 66,6 66 1-5/812 13,5 M12x45 1/213 UNC x 1-3/4
350 400 32 1-1/4 BFX-604-J1-5/8-M14 27,5 24 75 95 31,6 66,6 66 1-5/812 15 M14x45
350 400 38 1-1/2 BFX-605-J1-7/8 33 27 84 108 36,5 79,3 73 1-7/812 17 M16x50 5/811 UNC x 2
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
For UNC threaded bolts, use hexagon head bolts only. Please note that these do not belong to our product range.
3
Alternative options shown in brackets are available on request.
G36 www.stauff.com
Order Codes T
G
I
A
**BSPP
SAE 90 Single-Part Screw-in
Threaded Flange (without O-ring)
BFX90-...-G
M
**deviant screw-in BSPP thread, BFX90-...-G
** #K
Bolt
Q
including Metric bolts 8.8, spring rings,
O-ring made of NBR (Buna-N)
(packed in kits)
F
H
**including Metric bolts 10.9, BFX90-...-G-MH#K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
D K
**including UNC bolts (Gr8), BFX90-...-G-V-U#K
spring rings, O-ring made of FPM (Viton) P
(packed in kits) Material S355J0 or equivalent
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
350 400 32 1-1/4 BFX90-604-G 32 25 95 93 31,6 66,6 25 38 56 1-1/4 13,5 M12x45 1/213 UNC x 1-3/4
350 400 32 1-1/4 BFX90-604-G-M14 32 25 95 93 31,6 66,6 25 38 56 1-1/4 15 M14x45
350 400 38 1-1/2 BFX90-605-G 38 25 110 110 36,5 79,3 28 42 65 1-1/2 17 M16x50 5/811 UNC x 2
350 400 51 2 BFX90-606-G 51 35 132 134 44,5 96,8 33 45 75 2 21 M20x70 3/410 UNC x 2-3/4
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
For UNC threaded bolts, use hexagon head bolts only. Please note that these do not belong to our product range.
3
Alternative options shown in brackets are available on request.
Flanges
G
www.stauff.com G37
T G
Order Codes
A I
**NPT
SAE 90 Single-Part Screw-in BFX90-...-N
M
Threaded Flange (without O-ring)
Bolt
**deviant screw-in NPT thread, BFX90-...-N
** #K
Q
including Metric bolts 8.8, spring rings,
O-ring made of NBR (Buna-N) (packed in kits)
F
**including Metric bolts 10.9, BFX90-...-N-MH#K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
D K
P **including UNC bolts (Gr8), BFX90-...-N-V-U#K
spring rings, O-ring made of FPM (Viton)
(packed in kits)
Material S355J0 or equivalent
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
350 400 32 1-1/4 BFX90-604-N 32 25 95 93 31,6 66,6 25 38 56 1-1/4 13,5 M12x45 1/213 UNC x 1-3/4
350 400 32 1-1/4 BFX90-604-N-M14 32 25 95 93 31,6 66,6 25 38 56 1-1/4 15 M14x45
350 400 38 1-1/2 BFX90-605-N 38 25 110 110 36,5 79,3 28 42 65 1-1/2 17 M16x50 5/811 UNC x 2
350 400 51 2 BFX90-606-N 51 35 132 134 44,5 96,8 33 45 75 2 21 M20x70 3/410 UNC x 2-3/4
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
For UNC threaded bolts, use hexagon head bolts only. Please note that these do not belong to our product range.
3
Alternative options shown in brackets are available on request.
G38 www.stauff.com
Order Codes G
P I
**SAE 90 Single-Part Butt
Weld Flange (without O-ring)
BFX90-...-STC-
**/** A B
Bolt
Q
(packed in kits)
** ** ** -MH#K
incl. Metric bolts 10.9, BFX90-...-STC- /
F
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
D K
PN (bar)1 Nominal Size Order Codes Dimensions (mm) for Bolts Version
bolts
8.8 10.9 (MH) DN (in) A B D F G H I P Q K Metr.
2
350 350 19 3/4 BFX90-302-STC-27/19 19 27 21 63 70 22,3 47,6 23 41 11 M10x40 A
350 350 25 1 BFX90-303-STC-34,5/23 23 34,5 24 72 75 26,2 52,4 25 48 11 M10x45 A 3
B
G
A I
Bolt
Q
F
H
K
D
PN (bar)1 Nominal Size Order Codes Dimensions (mm) for Bolts Version
bolts
8.8 10.9 (MH) DN (in) A B D F G H I P Q K Metr.
350 400 19 3/4 BFX90-602-STC-28/19 19 28 19 70 71 23,8 50,8 22 40 11 M10x35 B
350 400 25 1 BFX90-603-STC-34/25 25 34 24 82 81 27,8 57,2 27 47 13 M12x45 B
350 400 32 1-1/4 BFX90-604-STC-42/32-M14 32 42 27 95 95 31,8 66,6 32 56 15 M14x50 B
350 400 38 1-1/2 BFX90-605-STC-48/38 38 48 30 115 113 36,5 79,3 40 68 17 M16x50 B
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
Flanges
www.stauff.com G39
A I
Order Codes
Q
Bolt
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
** ** **
incl. Metric bolts 10.9, BFX90-...-SRE- / -MH#K
F
A1
spring rings, O-ring made of NBR (Buna-N)
H
(packed in kits)
** ** **
incl. UNC bolts (Gr8), BFX90-...-SRE- / -V-U#K
spring rings, O-ring made of FPM (Viton)
D K (packed in kits)
Material S355J0 or equivalent P
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
For UNC threaded bolts, use hexagon head bolts only. Please note that these do not belong to our product range.
3
Alternative options shown in brackets are available on request.
G40 www.stauff.com
Order Codes
B G
A
**SAE 90 Single-Part Socket BFX90-...-ES- /
** ** I
M
Weld Flange (without O-ring)
Bolt
**incl. Metric bolts 8.8,
** **
BFX90-...-ES- / #K
spring rings, O-ring made of NBR (Buna-N)
Q
(packed in kits)
H
** ** **
incl. Metric bolts 10.9, BFX90-...-ES- / -MH#K
F
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
** ** **
incl. UNC bolts (Gr8), BFX90-...-ES- / -V-U#K
spring rings, O-ring made of FPM (Viton) (packed
D K
in kits) P
Material S355J0 or equivalent
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
For UNC threaded bolts, use hexagon head bolts only. Please note that these do not belong to our product range.
3
Alternative options shown in brackets are available on request.
Flanges
G
www.stauff.com G41
SAE 90 Single-Part Fitting Flange with 24 Cone Connector (acc. to ISO 8434-1 / DIN 2353)
BFX90-L/S
T
B G Order Codes
12 I
A
**SAE 90 Single-Part
Fitting Flange (without O-ring)
**/-S**
BFX90-...-L
Bolt
spring rings, O-ring made of NBR (Buna-N)
Q
(packed in kits)
** **
including Metric bolts 10.9, BFX90-...-L -MH#K
F
H
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
350 400 32 1-1/4 BFX90-604-S30-M14 25 30 S 25 95 93 31,8 66,6 36 58 42x2 15 M14x45 1/213 UNC x 1-3/4
350 350 38 1-1/2 BFX90-605-S38 32 38 S 26 110 110 36,5 79,3 41 65 52x2 17 M16x50 5/811 UNC x 2
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9). The actual maximum working pressure depends on the thickness
and the quality of the tube used.
2
For UNC threaded bolts, use hexagon head bolts only. Please note that these do not belong to our product range.
G42 www.stauff.com
Flanges
G
www.stauff.com G43
F
H
Order Codes
Bolt
**SAE Single-Part Blanking Flange
(without O-ring)
BFX-...-CP
G
I
**including Metric bolts 10.9, BFX-...-MH-CP#K
spring rings, O-ring made of NBR (Buna-N)
(packed in kits)
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9).
2
For UNC threaded bolts, use hexagon head bolts only. Please note that these do not belong to our product range.
3
Alternative options shown in brackets are available on request.
G44 www.stauff.com
G
I
D H
F
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9).
3
Alternative options shown in brackets are available on request.
Flanges
G
www.stauff.com G45
SAE Sandwich Plate (e.g. for Test Coupling) - Female BSPP Port
SPL-G1/4-L
G1/4
K
Order Codes
Version A
H
F
**SAE Sandwich Plate
(e.g. for Test Point) Female BSPP Port
SPL-...-G1/4-L
I
G
A
G
I
G1/4
K
D Please see STAUFF Test section
for further information on the
H
F
Material S355J0/C45 or equivalent Version B corresponding test couplings.
Surface blank, oiled
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9).
G46 www.stauff.com
SAE Blindplug
CAG-BP / CAG-BPH (high Version)
L1
Order Codes
D
C
* SAE Blindplug - high Version
(without O-ring)
CAG-BPH-...
L L
Material S355J0/C45 or equivalent
CAG-BP CAG-BPH Surface CrVl free
Special Material Stainless Steel 1.4571 -W5 on request
BP BPH DN (in) C D L L1
210 350 13 1/2 CAG-BP-301 CAG-BPH-301 24 30,2 6,8 15
210 350 19 3/4 CAG-BP-302 CAG-BPH-302 31,5 38,1 6,8 16
210 315 25 1 CAG-BP-303 CAG-BPH-303 38 44,45 8 18
200 250 32 1-1/4 CAG-BP-304 CAG-BPH-304 43 50,8 8 18
160 200 38 1-1/2 CAG-BP-305 CAG-BPH-305 50 60,35 8 18
160 200 51 2 CAG-BP-306 CAG-BPH-306 61,8 71,4 9,6 21
100 160 64 2-1/2 CAG-BP-307 CAG-BPH-307 73,8 84,1 9,6 21
100 160 76 3 CAG-BP-308 CAG-BPH-308 90 101,6 9,6 24
35 35 89 3-1/2 CAG-BP-309 CAG-BPH-309 102 114,3 11,3 45
35 35 102 4 CAG-BP-310 CAG-BPH-310 114 127 11,3 55
BP BPH DN (in) C D L L1
250 350 13 1/2 CAG-BP-601 CAG-BPH-601 24 31,8 7,8 18
250 350 19 3/4 CAG-BP-602 CAG-BPH-602 32 41,3 8,8 21
250 350 25 1 CAG-BP-603 CAG-BPH-603 38 47,6 9,5 26
250 350 32 1-1/4 CAG-BP-604 2 CAG-BPH-604 2 43,8 54 10,3 31
250 350 38 1-1/2 CAG-BP-605 CAG-BPH-605 50,8 63,5 12,6 34
250 350 51 2 CAG-BP-606 CAG-BPH-606 66,5 79,4 12,6 42
250 350 64 2-1/2 CAG-BPH-607 89 108 21,2 45
2
According to ISO 6162-2 bolts M12 should be used but because usually bolts M14 are used the description of the complete clamp must show M14 (e.g. CAG-BP-604-M14#K).
Flanges
G
www.stauff.com G47
G
Order Codes
I D
K
F
H
A
Material ST35 or equivalent
Surface blank, oiled
DN (in) A D F G H I K
13 1/2 SPL-301 13 3 47 57 17,5 38,1 9
19 3/4 SPL-302 19 3 49 66 22,3 47,6 11
25 1 SPL-303 25 3 53 71 26,2 52,4 11
32 1-1/4 SPL-304 32 3 69 80 30,2 58,7 11,5
38 1-1/2 SPL-305 38 3 77 95 35,7 69,9 13,5
51 2 SPL-306 51 3 89 103 42,9 77,8 13,5
64 2-1/2 SPL-307 63 3 101 116 50,8 88,9 13,5
76 3 SPL-308 73 4 124 136 61,9 106,4 17
89 3-1/2 SPL-309 89 4 136 152 69,8 120,7 17
102 4 SPL-310 99 4 146 162 77,8 130,2 17
127 5 SPL-311 120 4 180 184 92 152,4 17
DN (in) A D F G H I K
13 1/2 SPL-601 13 4 47 57 18,2 40,5 9
19 3/4 SPL-602 17 4 53 71 23,8 50,8 11
25 1 SPL-603 24 4 66 80 27,8 57,2 13
32 1-1/4 SPL-604-M14 31 4 77 94 31,8 66,6 15
38 1-1/2 SPL-605 38 4 89 103 36,5 79,3 17
51 2 SPL-606 51 4 116 135 44,5 96,8 21
64 2-1/2 SPL-607 63 4 150 166 58,7 123,8 25
76 3 SPL-608 73 4 178 208 71,4 152,4 32
G48 www.stauff.com
Order Codes G
I D
** SAE Cover Plate CPL-...
K
H
F
Material ST35 or equivalent
Surface blank, oiled
DN (in) D F G H I K
13 1/2 CPL-301 3 47 57 17,5 38,1 9
19 3/4 CPL-302 3 49 66 22,3 47,6 11
25 1 CPL-303 3 53 71 26,2 52,4 11
32 1-1/4 CPL-304 3 69 80 30,2 58,7 11,5
38 1-1/2 CPL-305 3 77 95 35,7 69,9 13,5
51 2 CPL-306 3 89 103 42,9 77,8 13,5
64 2-1/2 CPL-307 3 101 116 50,8 88,9 13,5
76 3 CPL-308 4 124 136 61,9 106,4 17
89 3-1/2 CPL-309 4 136 152 69,8 120,7 17
102 4 CPL-310 4 146 162 77,8 130,2 17
127 5 CPL-311 4 180 184 92 152,4 17
DN (in) D F G H I K
13 1/2 CPL-601 4 47 57 18,2 40,5 9
19 3/4 CPL-602 4 53 71 23,8 50,8 11
25 1 CPL-603 4 66 80 27,8 57,2 13
32 1-1/4 CPL-604-M14 4 77 94 31,8 66,6 15
38 1-1/2 CPL-605 4 89 103 36,5 79,3 17
51 2 CPL-606 4 116 135 44,5 96,8 21
64 2-1/2 CPL-607 4 150 166 58,7 123,8 25
76 3 CPL-608 4 178 208 71,4 152,4 32
Flanges
G
www.stauff.com G49
L
Order Codes
Thread
A1
A
I1
G
I
K1
K
H
H1
Material S355J0 or equivalent
Surface blank, oiled F
Special Material Stainless Steel 1.4404 -W5 on request
G50 www.stauff.com
Flanges
G
www.stauff.com G51
H
F
**Deviant surface treatment (blank, oiled) BF-T-...-W1
R
A
L
Material S355J0 or equivalent
R1
Surface CrVI-free
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9).
G52 www.stauff.com
F
H
**Deviant surface treatment (blank, oiled) BC-T-...-W1
R
A
Thread
L
R1
Material S355J0 or equivalent
Surface CrVI-free
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9).
Flanges
G
www.stauff.com G53
G
I Order Codes
H
F
** surface treatment (blank, oiled) BF-L-...-W1
R
K
L
R1
Material S355J0 or equivalent
Surface CrVI-free
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9).
G54 www.stauff.com
H
F
**Deviant surface treatment (blank, oiled) BC-L-...-W1
R
Thread
L
R1
Material S355J0 or equivalent
Surface CrVI-free
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9).
Flanges
G
www.stauff.com G55
H1
**deviant screw holes
**
BF-L-...-M -...
F
**Deviant surface treatment (blank, oiled) BF-L-...-...M
deviant threads
**
R
** BF-L-...-W1
I
A1
H
L
R1
Material S355J0 or equivalent
Surface CrVI-free
Special Material Stainless Steel 1.4404 -W5 on request
1
The maximum working pressure PN (bar) applies only to the flange itself and depends on the bolts used (Grade 8.8 / 10.9).
G56 www.stauff.com
Accessories
Thread diameter, length (see corresponding catalogue pages) and type (8.8 or 10.9 for MH / Gr8 for U) have to be replaced
according to your requirements. Bolts MH (Strength Properties 10.9) are delivered in blank, oiled. Please replace W66 (zinc
plated) for Metric bolts and W1 (blank, oiled) with W5 to order Stainless Steel (1.4571) bolts.
FPM (Viton)
Shore Hardness 85 ... 90 Shore
Temperature Range -20 C ... +200 C / -4 F ... +392 F
3000 PSI Standard Pressure Series (according to ISO 6162-1) 6000 PSI High Pressure Series (according to ISO 6162-2)
www.stauff.com G57
Instructions
To determine flange type and size, place flange over
drawing provided and line up holes.
G58 www.stauff.com
Instructions
To determine flange type and size, place flange over
drawing provided and line up holes.
Flanges
G
www.stauff.com G59
Nominal Diameter Tightening Working Burst Nominal Diameter Tightening Working Burst
Size Torques Pressure Pressure Size Torques Pressure Pressure
ISO SAE (Nm)+10% max (bar) min (bar) ISO SAE (Nm)+10% max (bar) min (bar)
13 1/2 M8 24 350 1400 13 1/2 M8 32 350 1400
19 3/4 M10 50 350 1400 19 3/4 M10 70 350 1400
25 1 M10 50 250 1000 25 1 M10 70 315 1260
32 1-1/4 M10 50 200 800 32 1-1/4 M10 70 250 1000
38 1-1/2 M12 92 200 800 38 1-1/2 M12 130 200 800
51 2 M12 92 160 640 51 2 M12 130 200 800
64 2-1/2 M12 92 100 400 64 2-1/2 M12 130 160 640
76 3 M16 210 100 400 76 3 M16 295 160 640
89 3-1/2 M16 210 35 140 89 3-1/2 M16 295 35 140
102 4 M16 210 35 140 102 4 M16 295 35 140
127 5 M16 210 35 140 127 5 M16 295 35 140
6000 PSI High Pressure Series (according to ISO 6162-2:2006) 6000 PSI High Pressure Series (according to ISO 6162-2:2006)
Nominal Diameter Tightening Working Burst Nominal Diameter Tightening Working Burst
Size Torques Pressure Pressure Size Torques Pressure Pressure
ISO SAE (Nm)+10% max (bar) min (bar) ISO SAE (Nm)+10% max (bar) min (bar)
13 1/2 M8 24 350 1400 13 1/2 M8 32 400 1600
19 3/4 M10 50 350 1400 19 3/4 M10 70 400 1600
25 1 M12 92 350 1400 25 1 M12 130 400 1600
32 1-1/4 M12 92 350 1400 32 1-1/4 M12 130 400 1600
32 1-1/4 M14 1 130 350 1400 32 1-1/4 M14 1 180 400 1600
38 1-1/2 M16 210 350 1400 38 1-1/2 M16 295 400 1600
51 2 M20 400 350 1400 51 2 M20 550 400 1600
Nominal Diameter Tightening Working Burst Attention: All bolts have to be pre-tightened before applying the full tightening torque
Size Torques Pressure Pressure to the bolts. Otherwise, the flange may break.
ISO SAE (Nm)+10% max (bar) min (bar)
13 1/2 5/16-18 UNC 32 350 1400 Please note that the tightening torques as stated above are only recommendations. These
19 3/4 3/8-16 UNC 60 350 1400 values correspond to oiled bolts with a friction coefficient of 0.17 and the material combination
25 1 3/8-16 UNC 60 315 1260 Steel/Steel. The exact tightening torques depend on factors like material, finishing, coating
32 1-1/4 7/16-14 UNC 92 250 1000 and lubrication of the components used, and have to be determined by the user himself.
38 1-1/2 1/2-13 UNC 150 200 800
51 2 1/2-13 UNC 150 200 800
64 2-1/2 1/2-13 UNC 150 160 640
76 3 5/8-11 UNC 295 160 640
89 3-1/2 5/8-11 UNC 295 35 140
102 4 5/8-11 UNC 295 35 140
127 5 5/8-11 UNC 295 35 140
G60 www.stauff.com
Flanges
G
www.stauff.com G61
4-hole Flange Connection with 24 Cone Connector (acc. to ISO 8434-1 / DIN 2353)
GP-LK-L/S
Order Codes
F
L
LK
**4-hole Flange Connection
with 24 Cone Connector
GP-LK...-L/S...#K
Bolt
12
Including Metric bolts 8.8, spring rings and
O-ring made of NBR (Buna-N)
A
(packed in kits)
D K
1
The maximum working pressure PN (bar) applies only to the flange itself. The actual maximum working pressure depends on the thickness and the quality of the tube used.
G62 www.stauff.com
4-hole 90 Flange Connection with 24 Cone Connector (acc. to ISO 8434-1 / DIN 2353)
WP-LK-L/S
T
B
Order Codes
12
* with
4-hole 90 Flange Connection
24 Cone Connector
WP-LK...-L/S...#K
Q
Bolt
Including Metric bolts 8.8, spring rings and
O-ring made of NBR (Buna-N)
(packed in kits)
F
A
D K
P LK
G Material S355J0 or equivalent
Surface ZnNi
2 x M6x22
100 WP-LK40-L28#K 40 20 28 L 9 61 42 28 40 36x2 6,4 26x2,5
2 x M6x50
2 x M6x22
100 WP-LK40-L35#K 40 20 35 L 9 62 42 34 41 45x2 6,4 26x2,5
2 x M6x60
2 x M6x22
250 WP-LK40-S20#K 40 20 20 S 9 61 42 22,5 40 30x2 6,4 26x2,5
2 x M6x45
2 x M8x25
100 WP-LK55-L35#K 55 26,5 35 L 12 78 58 32 49 45x2 8,4 32x2,5
2 x M8x60
2 x M8x25
100 WP-LK55-L42#K 55 26,5 42 L 12 78 58 40 49 52x2 8,4 32x2,5
2 x M8x70
2 x M8x25
250 WP-LK55-S20#K 55 18 20 S 13 69 58 24 45 30x2 8,4 32x2,5
2 x M8x50
2 x M8x25
250 WP-LK55-S25#K 55 26,5 25 S 13 78 58 30 49 36x2 8,4 32x2,5
2 x M8x55
2 x M8x25
250 WP-LK55-S30#K 55 26,5 30 S 12 78 58 32 49 42x2 8,4 32x2,5
2 x M8x50
1
The maximum working pressure PN (bar) applies only to the flange itself. The actual maximum working pressure depends on the thickness and the quality of the tube used.
Flanges
G
www.stauff.com G63
3-hole 90 Flange Connection with 24 Cone Connector (acc. to ISO 8434-1 / DIN 2353)
WP-3-LK-L/S
T
B 12 Order Codes
Q
Bolt
Including Metric bolts 8.8, spring rings and
O-ring made of NBR (Buna-N)
F
(packed in kits)
A
D K
P LK
Material S355J0 or equivalent G
Surface ZnNi
1
The maximum working pressure PN (bar) applies only to the flange itself. The actual maximum working pressure depends on the thickness and the quality of the tube used.
G64 www.stauff.com
Order Codes T
M
BSPP Threaded Flange
Q
Bolt
Including Metric bolts 8.8, spring rings and
F
O-ring made of NBR (Buna-N)
A
(packed in kits)
D
K
P LK
G
Material S355J0 or equivalent
Surface ZnNi
1
The maximum working pressure PN (bar) applies only to the flange itself. The actual maximum working pressure depends on the thickness and the quality of the tube used.
Flanges
G
www.stauff.com G65
Order Codes
M
BSPP Threaded Flange
Q
Bolt
Including Metric bolts 8.8, spring rings and
F
O-ring made of NBR (Buna-N)
(packed in kits)
A
D LK K
P G
Material S355J0 or equivalent
Surface ZnNi
1
The maximum working pressure PN (bar) applies only to the flange itself. The actual maximum working pressure depends on the thickness and the quality of the tube used.
G66 www.stauff.com
Order Codes T
**BSPP
3-hole 90 Screw-in WP-3-LK...-G...W50#K
M
Threaded Flange
Q
Bolt
Including Metric bolts 8.8, spring rings and
O-ring made of NBR (Buna-N)
F
A
(packed in kits)
D
K
P LK
G Material Aluminium [EN AC-Al Si9Cu(Fe)]
1
The maximum working pressure PN (bar) applies only to the flange itself. The actual maximum working pressure depends on the thickness and the quality of the tube used.
Flanges
G
www.stauff.com G67
T
Order Codes
M
BSPP Threaded Flange
Bolt
Q
Including Metric bolts 8.8, spring rings and
F
O-ring made of NBR (Buna-N)
A
(packed in kits)
K
D
LK
P
G
Material Aluminium [EN AC-Al Si9Cu(Fe)]
1
The maximum working pressure PN (bar) applies only to the flange itself. The actual maximum working pressure depends on the thickness and the quality of the tube used.
G68 www.stauff.com
D
Order Codes L LK
Bolt
Threaded Flange (Flat Style)
T
K Material S355J0 or equivalent
Surface CrVI-free
1
The maximum working pressure PN (bar) applies only to the flange itself. The actual maximum working pressure depends on the thickness and the quality of the tube used.
Flanges
G
www.stauff.com G69
L D Order Codes
D LK
**4-hole Butt Weld Flange GP-LK...-ST.../...#K
Bolt
Including Metric bolts 8.8, spring rings and
O-ring made of NBR (Buna-N)
(packed in kits)
A
K
8.8 LK A B D D L K Metr.
1
The maximum working pressure PN (bar) applies only to the flange itself. The actual maximum working pressure depends on the thickness and the quality of the tube used.
G70 www.stauff.com
Order Codes L D
D LK
Bolt
**with
4-hole Fitting Flange
60 Cone Connector
GP-LK...-AG...#K
M
A
O-ring made of NBR (Buna-N)
T
(packed in kits)
1
The maximum working pressure PN (bar) applies only to the flange itself. The actual maximum working pressure depends on the thickness and the quality of the tube used.
Flanges
G
www.stauff.com G71
L D Order Codes
D LK
Bolt
M **4-hole Screw-in BSPP
Threaded Flange
GP-LK...-G...#K
A
T
O-ring made of NBR (Buna-N)
(packed in kits)
1
The maximum working pressure PN (bar) applies only to the flange itself. The actual maximum working pressure depends on the thickness and the quality of the tube used.
G72 www.stauff.com
Flanges
G
www.stauff.com G73