Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Technical Handbook
ASME B73.1
A7
Chemical
Processing
Pump
Model
Wilfley Model A7 Chemical Processing Pumps
Expeller
2
Wilfley Model A7 Features and Benefits
Extra case wall thickness Close-fitting lip excludes Standard labyrinth seal Wide range of
extends wear life. contaminants from primary materials available.
seal.
Optional vapor seal Guards isolate
meets EPA requirements. all moving parts.
Centrifugally actuated
seal provides smooth
and efficient seal Cartridge-type Wilfley Optimum shaft size
opening and closing. hydronamic seal to to transmit loads and
simplify maintenance. maximize sealing flexibility.
Rotary and
stationary seal
faces are open
during operation
and closed to
prevent leakage
when the pump
is shutdown.
Large impeller
vanes provide
highly-efficient
pumping with
long wear life.
DryLock Features
The DryLock uses the action of
centrifugal force combined with the
smooth actuation of ball bearings to
open and close the seal. As the Seal activation can easily be
pump starts up, the expeller changed to open and close
evacuates the liquid in the seal at different speeds simply by
area. The balls of the DryLock are adding or subtracting balls.
forced outward and slide up a ramp
created by the ball housing. The
ramp forces the balls into the
actuator plate and opens the seal Multiple seal Isolated spring for
faces. Upon shut-down, the balls face materials reliable seal action.
lose their centrifugal force allowing available.
the spring-loaded actuator plate to
move back into its closed position.
The seal is then closed.
Pump Running/
Seal Open
Hook sleeve design
for maximum shaft
protection.
5
ey Options Seal
Diaphram Seal
Carbon Drylock/Drain Seal
For Fine Solids Services
6
Model A7 Pump Capacities
60 cycle performance
3550 RPM
700 A30-13 3x2-13
600 A20-13
3x1.5-13
500
A60-10
HEAD (FT)
100 AA-6
1.5x1-6
AB-6 A60-8 A70-8
3x1.5-6 3x2-8 4x3-8
A110-16 8x6-16S
210
A30-13 A40-13 A120-16
3x2-13 4x3-13 10x8-16S
A80-13
160 6x4-13
A20-13 A50-10 A60-10
HEAD (FT)
110
A110-15
A06-10 2x1-10 8x6-15
A70-10 A80-10
60 A50-8 4x3-10 6x4-10
AA-8 1x1.5-8 3x1.5-8
A120-15
A70-8 10x8-15
AA-6 1.5x1-6
AB-6 3x1.5-6 A60-8 3x2-8 4x3-8
100
A110-16 8x6-16S
A30-13 A40-13
80 3x2-13 4x3-13 A120-16
A80-13 10x8-16S
6x4-13
HEAD (FT)
A20-13
60 3x1.5-13
A110-15
40 8x6-15
A05-10
2x1-10 A80-10
6x4-10
20
A120-15
A50-10 A60-10 A70-10 10x8-15
3x1.5-10 3x2-10 4x3-10
2950 RPM
170
150 A40-13
4x3-13
130
A20-13 A50-10
110 3x1.5-13 3x1.5-10 A60-10 A30-13
3x2-13
HEAD (M)
3x2-10
90
A06-10
70 2x1-10 A80-10
A70-10 6x4-10
50 4x3-10
AA-8 1x1.5-8 A50-8
3x1.5-8
30
AA-6 1.5x1-6
10 AB-6 A70-8
3x1.5-6 A60-8 3x2-8 4x3-8
1 10 100 1000
FLOW (M3/HR)
1450 RPM
50
A110-16 8x6-16S
A30-13 A40-13 A120-16
40
3x2-13 4x3-13 10x8-16S
A80-13
6x4-13
HEAD (M)
8
Materials
9
14 17 15 67 62a 61 61a 62
72
76
72a
75
73
3 1 4 1a 61b 79
10
Model A7 Options and Engineering Specials
Frame with large sight glass Sight glass on the opposite side or
on the right side when viewed on both sides
from coupling end. Oil cooling provisions
O-Ring material: Viton Kalrez
Teflon encapsulated
Wet end material: DI, 316SS, A20, 1/2" NPT connection for case drain 1/4" NPT connection for gauge
WCD4, High Nichol Alloy, Max5/Ma8 Steam jackets Alloys special order
150 lbs. raised faced flanges 300 lbs raised faced flanges
Special Modifications
A.R. Wilfley & Sons is dedicated to Wilfley engineers assist in any
manufacturing pumps that maximize special configurations that the liquid
their full potential. Wilfley routinely and process require. Wilfleys
accommodates customer requests famous high-quality workmanship
for steam jackets, special paint, applies to all special designs to
flush ports, special drain plugs and customers needs.
other modifications required to fit
specific needs.
Many applications require special
motor and drive configurations,
including baseplates and mounting
brackets. Non-metallic and
fabricated baseplates are available.
11
Construction Details
AA-6 AB-6 AA-8 A5O-8 A60-8 A70-8 A05-10 A50-10 A60-10 A70-10 A80-10 A20-13 A30-13 A40-13 A80-13 A110-15 A120-15
General
Pump weight 137 lbs 167 152 371 375 411 420 468 473 492 549 478 490 528 574 1090 1207
62 kg 76 69 168 170 186 191 212 215 223 249 217 222 240 260 494 547
Max. solids size 3/16 in. 1/4 5/16 1/4 1/4 3/8 1/4 3/8 3/8 3/8 3/8 1/4 3/8 3/8 3/8 1/2 1/2
5 mm 6 8 6 6 10 6 10 10 10 10 6 10 10 10 13 13
Shaft
Diameter at .75 in. 1 1.125 2.125
Impeller 19 mm 25.4 28.6 53.9
Bearings
Standard radial 6308 6311 6312 6319A
bearing
*Modified seal configurations are available for special pumping conditions up to 400 F.
12
Dimensions
1 AA 1.5 X 1 X 6 (40 X 25 X 150) 17.5 (445) 5.25 (133) 6.5 (165) 4 (102) 143T - 184T 80M - 90L 139
AB 3 X 1.5 X 6 (80 X 40 X 150) 17.5 (445) 5.25 (133) 6.5 (165) 4 (102) 213T-256T 132M - 160L 148
AA 1.5 X 1 X 8 (40 X 25 X 200) 17.5 (445) 5.25 (133) 6.5 (165) 4 (102) 284TS - 326TS 180M - 180L 153
2 A50 3 X 1.5 X 8 (80 X 40 X 200) 23.5 (597) 8.25 (210) 8.5 (216) 4 (102)
A60 3 X 2 X 8 (80 X 50 X 200) 23.5 (597) 8.25 (210) 9.5 (242) 4 (102)
A70 4 X 3 X 8 (100 X 80 X 200) 23.5 (597) 8.25 (210) 11 (280) 4 (102)
A05 2 X 1 X 10 (50 X 25 X 250) 23.5 (597) 8.25 (210) 8.5 (216) 4 (102) 143T - 184T 100L - 132M 245
A50 3 X 1.5 X 10 (80 X 40 X 250) 23.5 (597) 8.25 (210) 8.5 (216) 4 (102) 213T - 215T 160M 180L 252
A60 3 X 2 X 10 (80 X 50 X 250) 23.5 (597) 8.25 (210) 9.5 (242) 4 (102) 254T - 286T 200L 258
A70 4 X 3 X 10 (100 X 80 X 250) 23.5 (597) 8.25 (210) 11 (280) 4 (102) 324TS - 365T 225S - 225M 264
A80 6 X 4 X 10 (150 X 100 X 250) 23.5 (597) 10 (254) 13.5 (343) 4 (102) 404T - 405TS 250M 268
405T - 449TS 280S 280M 280
A20 3 X 1.5 X 13 (80 X 40 X 330) 23.5 (597) 10 (254) 10.5 (266) 4 (102)
A30 3 X 2 13 (80 X 50 X 330) 23.5 (597) 10 (254) 11.5 (292) 4 (102)
A40 4 X 3 X 13 (100 X 80 X 330) 23.5 (597) 10 (254) 12.5 (318) 4 (102)
A80 6 X 4 X 13 (150 X 100 X 330) 23.5 (597) 10 (254) 13.5 (343) 4 (102)
3 A110 8 X 6 X 15 (200 X 150 X 380) 33.875 (860) 14.5 (368) 18 (457) 6 (152) 284T - 286T 180L 368
A120 10 X 8 X 15 (250 X 200 X 380) 33.875 (860) 14.5 (368) 19 (483) 6 (152) 324T - 405T 200L - 250M 380
444T - 449T 280S - 315L 398
The dimensions listed above conform All dimensions printed in black are in
to ASME B73.1 specifications and inches and those in red are the
apply to fabricated and non-metallic approximate equivalent in millimeters.
base plates only. dimensions are
different for iron bases. Flanges are drilled to match ASME
B16.5 150lbs.
These dimensions are not for
construction. Certified dimension
prints are available for your specific
installation.
13
General Installation Recommendations
HA HG
HB HD HE HF HH HL HP
(MAX) (MAX)
15 (381) 39 (991) 9 (229) 4.5 (114) 36.5 (927) 3.75 (95) .75 (19) 4.5 (114) 1.25 (32)
18 (457) 48 (1219) 10.5 (267) 6 (152) 45.5 (1156) 4.13 (105) .75 (19) 4.5 (114) 1.25 (32)
21 (533) 53 (1346) 12.88 (327) 7.5 (191) 50.5 (1283) 4.75 (121) .75 (19) 4.5 (114) 1.25 (32)
Frame 2 Frame 3
(and 6x4x10)
15 (381) 45 (1143) 12 (305) 13.75 (349) 4.5 (114) 42.5 (1080) 3.75 (95) .75 (19) 4.5 (114) 1.25 (32)
18 (457) 52 (1321) 12.38 (314) 14.13 (359) 6 (152) 49.5 (1257) 4.13 (105) .75 (19) 4.5 (114) 1.25 (32)
21 (533) 58 (1473) 13 (330) 14.75 (375) 7.5 (191) 55.5 (1410) 4.75 (121) 1.00 (25) 4.5 (114) 1.25 (32)
21 (533) 64 (1626) 13.88 (353) 14.75 (375) 7.5 (191) 61.5 (1562) 4.75 (121) 1.00 (25) 4.5 (114) 1.25 (32)
26 (660) 68 (1727) 14.88 (378) 14.88 (378) 9.5 (241) 65.5 (1664) 4.75 (121) 1.00 (25) 4.5 (114) 1.25 (32)
26 (660) 80 (2032) 15.88 (403) 15.88 (403) 9.5 (241) 77.5 (1969) 4.75 (121) 1.00 (25) 4.5 (114) 1.25 (32)
26 (660) 68 (1727) 19.25 (489) 9.5 (241) 65.5 (1664) 4.75 (121) 1.00 (25) 6.5 (165) 1.25 (32)
26 (660) 80 (2032) 19.25 (489) 9.5 (241) 77.5 (1969) 4.75 (121) 1.00 (25) 6.5 (165) 1.25 (32)
26 (660) 98 (2489) 19.25 (489) 9.5 (241) 95.5 (2426) 4.75 (121) 1.00 (25) 6.5 (165) 1.25 (32)
Choosing Pump Location after the complete unit has been specifications. Careful evaluation of
installed. Guidelines for checking pumping conditions is needed to
Locate the pump as close to the
and aligning the pump components provide accurate pump
liquid source as practical so the
may be found in the Hydraulic recommendations and quotations.
suction pipe is short and direct
Institute Standards.
with a minimum of elbows, This list will help establish specific
fittings and valves. Piping pumping system conditions.
Place the pump in a location so the Both suction and discharge pipes Liquid
unit is accessible for inspection should be supported independently Temperature
during operation as well as for near the pump so when the flange
Static Head
maintenance operations involving bolts are tightened no strain will be
removal and disassembly. transmitted to the casing. Discharge Pipe Size
Foundation A check valve should be be Length, Discharge Pipe
installed in the discharge line to Discharge Pipe Fittings
The foundation should be strong
prevent fluid from flowing back Equivalent Length Discharge Pipe
enough to absorb any vibration and
through the pump while it is shut
to form a permanent support for the Total Head
down. Gate valves should be
baseplate. This is important in
installed in both discharge and Maximum Suction Pressure
maintaining the alignment of the
suction lines to isolate the pump Minimum Suction Pressure
direct connected unit. Foundation
during maintenance.
bolts of the proper size should be Capacity
embedded in the concrete located Care must be taken in sizing and
by the outline drawing. locating suction piping to prevent Specific Gravity
cavitation. % Solids by Weight
Alignment
Ordering Information Mesh Analysis
The pump and motor are aligned at
the factory before shipment. Wilfley pumps are engineered to Viscosity
However, realignment is necessary operate in compliance with your NPSH Available
14
A.R. Wilfley & Sons, Inc.
303/779-1777
1-800-525-9930
FAX 303/779-1277
www.wilfley.com
A7T11-FK