Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Technical Catalogue
E0.130.0416.02.00IM02
GEAR PUMPS E- B- C SERIES
Aluminium Body General Features
GEAR PUMPS
SALAMI gear pumps are available with displacements from 1.4 cm3/rev to 99 cm3/rev (from 0.09 cu.in/rev to 6.03
cu.in/rev).
Multiple pumps can always be relized combining stages taken from different or same series.
Several options of shafts, flanges and ports as for European, German and American standards are available for all
the pumps.
Technical Data
*Available on request.
Important:
in case of assembling of pumps without shaft seals (eg. B4 - B5....), you have to keep the value of min.
GEAR PUMP
suction pressure ( 0.8 bar (abs)) in the vane between pump and coupling too.
End
Features
plate
Lower pressure can lead to suction of oil through the front flange (seat of the shaft without seal);
PG SERIES
this can damage seriously the pump.
Definition Of Pressures
DEFINITION OF PRESSURES
P3 = Peak
P3 =pressure
Peak pressure
P2 = Intermittent operating
P2 = Intermittent pressurepressure
operating (1/3 of working time)
(1/3 of working time)
P1 = Continuous operating pressure
P1 = Continuous operating pressure
max. 20 s
GENERAL
www.salami.it 3
Superior performance and reliability in
heavy-duty hydraulic application.
GEAR PUMPS E- B- C SERIES
General Features Aluminium Body
DRIVE SHAFTS
Radial and axial loads on the shafts must be avoided since they reduce the life of the unit.
In order to avoid misalignment during the assembly with the primary engine, a connection with Oldham coupling (or
coupling having convex toothed hub) is recommended.
ROTATION
To ensure favorable suction conditions it is important to keep pressure drop in suction pipe line to a minimum value
(see TECHNICAL DATA).
To calculate hydraulic pipe line size, the designer can use; as an approximate guide, the following fluid speed figures:
From 1 to 2 m/sec on suction pipe line From 3.28 to 6.36 ft/sec on suction pipe line
From 6 to 10 m/sec on pressure pipe line From 19.7 to 32.8 ft/sec on pressure pipe line
The lowest fluid speed values in pipe lines is recommended when the operating temperature range is high and/or for
continuos duty.
The highest value is recommended when the temperature difference is low and/or for intermittent duty.
When tandem pumps are supplied by 2 different reservoirs with 2 different fluids it is necessary to specify AS
version.
4 www.salami.it
GEAR PUMPS E- B- C SERIES
Aluminium Body General Features
IDENTIFICATION LABEL
Wo0132803
www.salami.it 5
GEAR PUMPS E- B- C SERIES
General Features Aluminium Body
WORKING CONDITIONS
GROUP 2 - E SERIES cm3/rev cu.in/rev bar psi bar psi bar psi min-1
2PE - 3.2* 3.2 0.19 250 3625 280 4060 300 4350 4000 600
2PE - 3.9* 3.9 0.24 250 3625 280 4060 300 4350 4000 600
2PE - 4.5 4.6 0.27 250 3625 280 4060 300 4350 4000 600
2PE - 6.5 6.5 0.4 250 3625 280 4060 300 4350 4000 600
2PE - 8.3 8.2 0.5 250 3625 280 4060 300 4350 3500 500
2PE - 10.5 10.6 0.65 250 3625 280 4060 300 4350 3500 500
2PE - 11.3 11.5 0.68 250 3625 280 4060 300 4350 3500 500
2PE - 12.5 12.7 0.77 250 3625 280 4060 300 4350 3500 500
2PE - 13.8 13.8 0.84 250 3625 280 4060 300 4350 3500 500
2PE - 16 16.6 1.01 250 3625 280 4060 300 4350 3000 400
2PE - 19 19.4 1.15 220 3140 240 3480 260 3750 3000 400
2PE - 22.5 22.9 1.37 200 2900 220 3140 240 3480 2750 400
2PE - 26 25.8 1.58 180 2610 200 2900 220 3190 2500 400
*Available only as rear pump
GROUP 2.5 - B SERIES cm3/rev cu.in/rev bar psi bar psi bar psi min-1
2.5PB - 5.5* 5.97 0.36 250 3625 280 4060 300 4350 3000 600
E0.100.0416.02.00IM00
2.5PB - 8.3* 8.29 0.50 250 3625 280 4060 300 4350 3000 600
2.5PB - 11.5* 11.76 0.72 250 3625 280 4060 300 4350 3000 600
2.5PB - 13.8* 14.07 0.86 250 3625 280 4060 300 4350 3000 600
2.5PB - 16 16 0.97 250 3625 280 4060 300 4350 3000 600
2.5PB - 19 19.3 1.17 250 3625 280 4060 300 4350 3000 600
2.5PB - 22 22.2 1.35 250 3625 280 4060 300 4350 3000 500
2.5PB - 25 25.2 1.53 250 3625 280 4060 300 4350 3000 500
2.5PB - 28 27.6 1.68 250 3625 280 4060 300 4350 3000 500
2.5PB - 32 32.4 1.97 230 3330 250 3625 260 3750 3000 500
2.5PB - 38 38.1 2.32 200 2900 220 3140 240 3480 2750 400
2.5PB - 44 44.2 2.69 170 2465 190 2755 210 3040 2500 400
*Available only as rear pump. Displacements 11.5-13.8 are available as single pump only with drive shaft 55.
6 www.salami.it
GEAR PUMPS E- B- C SERIES
Aluminium Body General Features
GROUP 3.5 - C SERIES cm3/rev cu.in/rev bar psi bar psi bar psi min-1
3.5PC - 55 54.8 3.34 250 3625 280 4060 300 4350 2750 400
3.5PC - 64 63.2 3.85 250 3625 280 4060 300 4350 2750 350
3.5PC - 75 74.7 4.55 230 3330 250 3625 280 4060 2500 300
3.5PC - 87 88 5.36 210 3040 230 3330 260 3750 2250 300
3.5PC - 98* 99 6.03 200 2900 220 3140 250 3625 2000 300
*Displacement 98 are special release, please contact sales department.
**For working conditions, using exclusively pressure P1, the value of max. speed must be reduced of 10%.
The max pressure is refered to pumps with flanged ports, using the threaded ports the pump life could be
reduced.
E0.100.0416.02.00IM00
www.salami.it 7
GEAR PUMPS E- B- C SERIES
General Features Aluminium Body
Before starting, be sure that the pump is cleaned externally as well as the working area to avoid that particles
dangerous for pump working can find their way into the pump. Pump represented is a clockwise rotation pump.
To obtain an anti_clockwise rotation read carefully the following instructions.
1 - Draw out the driven gear from its housing, taking care to avoid
rear cover axial shifts.
2 - Re-locate the driven gear in the position previously occupied by
the driving gear.
8 www.salami.it
GEAR PUMPS E SERIES
Aluminium Body 3PE
INDEX
www.salami.it 83
GEAR PUMPS E SERIES
Aluminium Body 3PE
3PE
3P/ME
CODE P2 - European stand. CODE B6 - German stand. CODE P3 - European stand. for 3,5PC CODE S3 - SAE B
35B6
38P2
48P3
55S3
56S3
87S3
88S3
05B6
code 05 - tang drive
CODEfor
05 - electric motors
Tang drive for electric motors
www.salami.it 85
GEAR PUMPS E SERIES
3PE Aluminium Body
ASSEMBLING DIMENSIONS
cm /rev 3
20.6 27 33.5 38.7 46.9 54.1 63.1 73.4
Displacement
cu.in./rev 1.26 1.65 2.04 2.36 2.86 3.3 3.85 4.48
mm 74 79 84 88 104 110 117 124
Dimension A
in 2.91 3.11 3.31 3.46 4.09 4.33 4.61 4.88
mm 37 39.5 42 44 52 55 58.5 62
Dimension C
in 1.46 1.56 1.65 1.73 2.05 2.17 2.30 2.44
kg 8.6 8.9 9.1 9.4 10.1 10.5 10.8 11.2
Weight
lbs 19 19.6 20.1 20.6 22.3 23 23.8 24.6
95-105 Nm
22 32.5 122.9
.87 A 1.28 (70-77.4 lbfft) 4.84
5 19 98
.20 C 3.86
54.4
2.14
1.65
42
5.04
128
.87
22
98.4
3.88
E0.130.0416.02.00IM02
12
n.4 holes O .47
O 2.000 -.003
50.8 -0.076
-0.030
-.001
86 www.salami.it
GEAR PUMPS E SERIES
Aluminium Body 3PE
ASSEMBLING DIMENSIONS
Type 46 55 65 75*
3
cm /rev 46.9 54.1 63.1 73.4
Displacement
cu.in./rev 2.86 3.3 3.85 4.48
mm 104 110 117 124
Dimension A
in 4.09 4.33 4.61 4.88
mm 52 55 58.5 62
Dimension C
in 2.05 2.17 2.30 2.44
kg 10.1 10.5 10.8 11.2
Weight
lbs 22.3 23 23.8 24.6
95-105 Nm
22 32.5 (70-77.4 lbfft)
.87 A 1.28 136.2
5.36
5 19
.20 C 114.2
4.50
60.3
2.37
49.3
1.94
.87
22
149.3
5.88
4.37
111
E0.130.0416.02.00IM02
Tapered 1:8
O 11
.43
www.salami.it 87
GEAR PUMPS E SERIES
3PE Aluminium Body
E0.130.0416.02.00IM02
88 www.salami.it
GEAR PUMPS E SERIES
Aluminium Body 3PE
Threaded ports
GAS (BSPP)
E0.130.0416.02.00IM02
1-5/16-12 1-1/16-12
From 25 49 21 41
UN UN
21 to 38 (0.98) (1.93) (0.83) (1.16)
(SAE 16) (SAE 12)
19 3.3 19 3.3
1-5/8-12 (0.75) (0.12) 1-5/16-12 (0.75) (0.13)
From 27 58 25 49
UN UN
46 to 75 (1.06) (2.28) (0.98) (1.93)
(SAE 20) (SAE 16)
code R
BI-DIRECTIONAL PUMPS Special version available on request.
Threaded ports
SAE (ODT)
www.salami.it 89
GEAR PUMPS E SERIES
3PE Aluminium Body
DRIVE SHAFTS
code 05 Max torque 180 Nm (1590 lbf in) code 35 Max torque 260 Nm (2300 lbf in) code 38 Max torque 250 Nm (2213 lbf in)
Tang drive for electric motors European tapered 1:5 European tapered 1:8
[0.984]
25
code 48 Max torque 350 Nm (3100 lbf in) code 55 Max torque 330 Nm (2921 lbf in) code 56 Max torque 480 Nm (4250 lbf in)
European tapered 1:8 for 3.5PC SAE B 13T-16/32DP Ansi B92 1a 1976 SAE BB 15T-16/32DP Ansi B92 1a 1976
E0.130.0416.02.00IM02
code 87 Max torque 220 Nm (1950 lbf in) code 88 Max torque 320 Nm (2830 lbf in)
90 www.salami.it
GEAR PUMPS E SERIES
Aluminium Body 3PE
MOUNTING FLANGES
www.salami.it 91
GEAR PUMPS E SERIES
3PE Aluminium Body
OUTRIGGER BEARING
TYPE H
27 79 (3.11) Fr
33 84 (3.31)
38 88 (3.46) L=Distance between
46 104 (4.09) mounting flange and
55 110 (4.33)
radial force point of
65 117 (4.61)
application.
Example:
Fr = 3000 N
Expected life: 1000 hrs
L = 35
Speed = 2500 rpm
H
For Code CP
E0.130.0416.02.00IM02
For Code CSB
92 www.salami.it
GEAR PUMPS E SERIES
Aluminium Body 3PE
CSB SAE B
www.salami.it 93
GEAR PUMPS E SERIES
3PE Aluminium Body
REAR COVER
external drain
DIMENSION C
Standard rear cover Standard rear cover
for unidirectional pumps for reversible pumps, with external drain C.
For the dimension C please see the table here below
C
G3/8
9/16-18 UNF-2B (SAE6)
E0.130.0416.02.00IM02
Outlet Inlet
DIMENSION B DIMENSION A
code 1
For pumps with threaded rear ports, suitable up to 80 l/min delivery.
A B
G1 G3/4
1-5/16-12 UN-2B 1-1/16-12 UN-2B
(SAE16) (SAE12)
94 www.salami.it
GEAR PUMPS E SERIES 3PE
Priority VALVES
Inlet
LS - Signal inlet
The double or triple pumps can be configurated with priority flow valve too.
The stage which has its flow divided into priority and exceeded flows is always the back one.
EF CF
EF CF
www.salami.it 95
GEAR PUMPS E SERIES
3PE Aluminium Body
VP1 - VPS1
SIDE PORTS
AXIS OF PUMP SHAFT
68.5 48 ANTI-CLOCKWISE ROTATION
2.70 1.89
59,9
2,4
2,5
64
59,9
E0.130.0416.02.00IM02
2,5
64
64
2,5
A D E
G 3/8 G 3/4 G 1/4
SAE8 SAE12 SAE4
3/4 - 16 UNF - 2B 1-1/16 - 12 UN - 2B 7/16 - 20 UNF - 2B
96 www.salami.it
GEAR PUMPS E SERIES
Aluminium Body 3PE
MULTIPLE MULTIPLE
GEAR PUMPS GEAR PUMPS
with inlet port with common
on each body inlet port*
*In case of common inlet port, to avoid too
high value of oil speed, 60 l/min is the max
sucked flow for the downstream pump.
59.9
2.36
.87
22
3.62
92
E0.130.0416.02.00IM02
www.salami.it 97
GEAR PUMPS E SERIES
3PE Aluminium Body
17
MULTIPLE
GEAR PUMPS
.87
with common 22
inlet port*
6.1
.24
*In case of common inlet port, to avoid too high
value of oil speed, 30 l/min is the max sucked
flow for the downstream pump or pumps.
2PE-Type 3.2* 3.9* 4.5 6.5 8.3 10.5 11.3 12.5 13.8 16 19 22.5 26
E0.130.0416.02.00IM02
A A
C
A
1.5PE-Type 1.4 2.1 2.8 3.5 4.1 5.2 6.2 7.6 9.3 11
98 www.salami.it
GEAR PUMPS E SERIES
Aluminium Body 3PE
PERFORMANCE CURVES
Performance curves carried out with oil viscosity at 21 cSt and oil temperature at 50C
40.00
70.00
Power
35.00
Flow rate [l/min] 20 bar [kW] 50
r
Flow rate [l/min] 300 bar bar
ba
Power
60.00 [kW] 100
0
ba
30
bar
Power
20
[kW] 150
bar
30.00
r
ba
r
ba
0
25
50.00
0
25
25.00
r
ba
20.00
ar
30.00 0b
15
15.00
bar
20.00 100
10.00
r
50 ba
10.00
5.00
0.00 0.00
0 500 1000 1500 2000 2500 3000 3500
0 800 1600 2400 3200
RPM RPM
3PE-21
90.00 Powe
Powe
Powe
Powe
80.00
Powe
r
ba
Powe
20
Flow rate r
0
ba
25
60.00
40.00
r
ba
0
25
35.00
Flow rate [l/min]
50.00
ar
30.00 0b
20
Input power [kW]
40.00
25.00
ar
0b
15
30.00
20.00
bar
15.00 100
20.00
10.00
r
50 ba
10.00
5.00
0.00 0.00
0 500 1000 1500 2000 2500 3000 3500 0 800 1600 2400 3200
RPM RPM
3PE-27
www.salami.it 99
GEAR PUMPS E SERIES
3PE Aluminium Body
60.00
120.00
r
ba
0
30
Flow rate [l/min] 20 bar
r
ba
ba
0
20
25
r
ba
0
40.00
25
80.00
r
ba
0
20
Power [kW] 50 b
20.00 10.00 50 ba
r
0.00
0.00
0 500 1000 1500 2000 2500 3000 3500
0 400 800 1200 1600 2000 2400 2800 3200
RPM
RPM
3PE-33
60.00
120.00
r
ba
0
28
Power [kW]
ba
100.00
0
bar
20
25
Power [kW]
bar
Power [kW]
r
ba
bar
0
r
24
40.00 ba E0.130.0416.02.00IM02
0
80.00 20
Input power [kW]
Flow rate [l/min]
30.00 ar
60.00 0b
15
20.00 bar
40.00 100
r
50 ba
20.00 10.00
0.00 0.00
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
RPM RPM
3PE-38
100 www.salami.it
GEAR PUMPS E SERIES
Aluminium Body 3PE
70.00
140.00
r
ba
0
28
Flow60.00
rate [l/min] 20 bar
r
ba
r
120.00
ba
0
Flow rate [l/min] 280 bar
25
20
r
ba
0
25
50.00
100.00 r
ba
0
20
80.00
ar
0b
15
30.00
60.00
bar
100
40.00 20.00
r
50 ba
20.00 10.00
0.00 0.00
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
RPM RPM
3PE-46
70.00
140.00 Power [kW] 40
bar
Power [kW] 80
bar
r
ba
Power [kW]
ar
120 bar
0b
20
Power [kW] 25
60.00
120.00 160 bar
r
ba
0
22
100.00 50.00
E0.130.0416.02.00IM02
r
ba
0
Flow rate [l/min]
40.00 16
Input power [kW]
80.00
ar
0b
12
60.00 30.00
20.00 r
10.00 40 ba
0.00
0 500 1000 1500 2000 2500 3000 0.00
0 500 1000 1500 2000 2500 3000
RPM
RPM
3PE-55
www.salami.it 101
GEAR PUMPS E SERIES
3PE Aluminium Body
80.00
160.00
Flow rate Power [kW] 40
r
[l/min] 20 bar
ba
r
bar
ba
70.00 Power [kW] 80
20
0
24
bar
ar
140.00 Power [kW] 120
0b
bar
20
60.00
r
ba
120.00
0
20
50.00
r
100.00 ba
0
16
40.00
80.00
ar
0b
12
30.00
60.00
bar
80
20.00
40.00
r
40 ba
20.00 10.00
0.00 0.00
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
RPM RPM
3PE-65
80.00
180.00
ar
0b
22
r
ba
ar
70.00
20
0b
160.00
18
r
ba
140.00 60.00
5
17
E0.130.0416.02.00IM02
120.00
50.00 r
ba
0
Flow rate [l/min] 20 bar 12
Input power [kW]
Flow rate [l/min]
30.00
60.00 bar
70
20.00
40.00
r
35 ba
10.00
20.00
0.00 0.00
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
RPM RPM
3PE-75
102 www.salami.it
GEAR PUMPS E SERIES
Aluminium Body 3PE-How to order
SINGLE PUMPs
Adjustable flow l/min
A B C D E F G H I L
3PE 33 D - P 38 P2 - V - 1 - CP - PD2 - VP1 ... / ...
Setting main
relief valve (bar)
Anti-clockwise S
European standard CP
Reversible R
German standard CSB
Order example 3PE 46D, ports SAE (R), drive shaft (56),
mounting flange (S3)
3PE46D-R56S3
www.salami.it 103
GEAR PUMPS E SERIES
How to order-3PE Aluminium Body
MULTIPLE PUMPS
Adjustable flow l/min
A B C D E F G H I L M
3PE 65 / 46 D - P 28 P2 - V UA - 1 - CP - PD2 - VPD1 ... / ...
Setting main
relief valve (bar)
Anti-clockwise S
European standard CP
German standard CSB
PORTS (page 88) CODES C
Flanged ports H PORTS POSITION CODE
P
european standard Lateral ports standard
Flanged ports
B Rear ports (page) 1
german standard
Threaded ports
G
GAS (BSPP)
G SUCTION PORTS CODES
Threaded ports
R Common suction UA*
SAE (ODT)
Flanged ports Separeted stages AS
SAE J518 AMERICAN S
STANDARD THREAD F SEAL CODE
Flanged ports Buna standard
W
SAE J518 METRIC THREAD
Viton V
DRIVE SHAFT (page 90) CODES D
E MOUNTING FLANGES (page 91) CODES
Tang drive for electric motors 05
SAE B 2 Bolts S3
European Tapered 1:5 35
European standard 50.8 P2
European Tapered 1:8 38 E0.130.0416.02.00IM02
European standard 60.3 P3
European Tapered 1:8 48
German standard 105 B6
SAE B splined 13T 55
SAE BB splined 15T 56
SAE B parallel 87
SAE BB parallel 88
Order example 3PE 33/27D, ports SAE (P), drive shaft (56),
mounting flange (S3)
3PE33/27D-R56S3
104 www.salami.it
You can find our most up to date STANDARD SALES CONDITIONS on our website.
Potete trovare le nostre pi aggiornate CONDIZIONI DI VENDITA STANDARD sul nostro sito.
www.salami.it
T. +39 059 387 411
sales@salami.it
www.salami.it