Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
C Int[Int(M dx)]dx + C1 x + C2
C Int[Int(M dx)]dx + C1 x + C2
A same
B double
C four times
D six times
Answer B
Marks 1
Unit
Id
Question A simply supported beam 'A' of length l, breadth b and depth d carries a central load W.
Another beam 'B' of the same dimensions carries a central load equal to 2W. The
deflection of beam 'B' will be __________ as that of beam 'A'.
A one-fourth
B one-half
C double
D four times
Answer C
Marks 1
Unit
Id
Question For a simply supported beam of length L carrying a couple moment M0 at the centre, EI
d2y/dx2 = ____________________.
A M0
B (-M0)
Answer C
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa ) having a point load at its free end and a
rectangular cross section of b x d shows a deflection of 4 mm at the free end. If the same
load is applied on the free end of another cantilever of the same material and length but
rectangular cross-section of 2b x d, the deflection at its free end will be __________mm.
A 1
B 2
C 4
D 8
Answer B
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa ) having a point load at its free end and a
rectangular cross section of b x d shows a deflection of 4 mm at the free end. If the same
load is applied on the free end of another cantilever of the same material and length but
rectangular cross-section of b x 2d, the deflection at its free end will be __________mm.
A 0.5
B 2
C 4
D 8
Answer A
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa ) having a point load at its free end and a
rectangular cross section of b x d shows a deflection of 4 mm at the free end. If the same
load is applied on the free end of another cantilever of the same material and length but
rectangular cross-section of 2b x 2d, the deflection at its free end will be __________mm.
A 0.25
B 2
C 4
D 48
Answer A
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa ) having a point load at its free end and a
rectangular cross section of b x d shows a deflection of 4 mm at the free end. If the same
load is applied on the free end of another cantilever of the same material but twice the
length and rectangular cross-section of b x 2d, the deflection at its free end will be
__________mm.
A 0.5
B 2
C 4
D 8
Answer C
Marks 2
Unit
Id
Question A cantilever beam of length 1 m having a point load at its free end shows a slope of 4 at
the free end. If the same load is applied on the free end of another cantilever of the same
cross-sectional dimensions but of length 2 m, the slope at it's free end will be ________.
A 0.5
B 2
C 4
D 16
Answer D
Marks 2
Unit
Id
Question A cantilever beam of length 1 m having a point load at its free end shows a slope of 4 at
the free end. If the same load is applied on the free end of another cantilever of the same
cross-sectional dimensions but of length 0.5 m, the slope at it's free end will be
________.
A 1
B 2
C 4
D 32
Answer A
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a point load at its free end shows a slope
of 4 at the free end. If the same load is applied on the free end of another cantilever of
the same cross-sectional dimensions and length but of copper (E = 100 GPa), the slope at
the free end will be _______.
A 0.5
B 2
C 4
D 8
Answer D
Marks 2
Unit
Id
Question A cantilever beam of copper (E = 100 GPa) having a point load at its free end shows a
slope of 4 at the free end. If the same load is applied on the free end of another cantilever
of the same cross-sectional dimensions and length but of steel (E = 200 GPa), the slope at
the free end will be _______.
A 1
B 2
C 4
D 8
Answer B
Marks 2
Unit
Id
Question A cantilever beam of copper (E = 100 GPa) having a point load of 10 kN at its free end
shows a slope of 4 at the free end. If the load of 20 kN is applied on the free end of
another cantilever of the same cross-sectional dimensions and length but of steel (E = 200
GPa), the slope at the free end will be _______.
A 1
B 2
C 4
D 8
Answer C
Marks 2
Unit
Id
Question A cantilever beam of copper (E = 100 GPa) having a point load of 10 kN at its free end
shows a slope of 1 at the free end. If the load of 20 kN is applied on the free end of
another cantilever of the same cross-sectional dimensions but double the length and of
steel (E = 200 GPa), the slope at the free end will be _______.
A 1
B 2
C 4
D 8
Answer C
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a point load at its free end and a
rectangular cross-section of b x d shows a slope of 4 at the free end. If the same load is
applied on the free end of another cantilever of the same material and length but
rectangular cross-section of 2b x d, the slope at the free end will be _______.
A 1
B 2
C 4
D 8
Answer B
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a point load at its free end and a
rectangular cross-section of b x d shows a slope of 4 at the free end. If the same load is
applied on the free end of another cantilever of the same material and length but
rectangular cross-section of b x 2d, the slope at the free end will be _______.
A 0.5
B 2
C 4
D 8
Answer A
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a point load at its free end and a
rectangular cross-section of b x d shows a slope of 4 at the free end. If the same load is
applied on the free end of another cantilever of the same material and length but
rectangular cross-section of 2b x 2d, the slope at the free end will be _______.
A 0.25
B 2
C 4
D 8
Answer A
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a point load at its free end and a
rectangular cross-section of b x d shows a slope of 4 at the free end. If the same load is
applied on the free end of another cantilever of the same material but twice the length and
rectangular cross-section of b x 2d, the slope at the free end will be _______.
A 0.5
B 2
C 4
D 8
Answer B
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa), 600 mm in length has a rectangular cross
section of width 60 mm x 100 mm depth is subjected to a point load of 10 kN at its free
end. The deflection at its free end will be _______________ mm.
A 0.52
B 0.72
C 0
D 5.2
Answer B
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa), 600 mm in length has a rectangular cross
section of width 60 mm x 100 mm depth is subjected to a point load of 10 kN at its free
end. The slope at its free end will be __________.
A 0.0018
B 0.0018 radian
C 0.72
D 0.72 radian
Answer B
Marks 2
Unit
Id
Question A rod of length 2 m and square cross section 100 mm x 100 mm elongates by 0.01 mm
when subjected to an axial load W. If the same rod is used as a cantilever and subjected to
the same load at its free end, the deflection at the free end will be ________mm.
A 0.01
B 10
C 4
D 16
Answer D
Marks 2
Unit
Id
Question A cantilever beam of copper (E = 100 GPa) having a UDL of 10 kN / m acting throughout
its length shows a deflection of 1 mm at the free end. If the UDL of 20 kN / m is applied
throughout the length on another cantilver of the same cross sectional dimensions but
double the length and of steel (E = 200 GPa), the deflection at the free end will
be________mm.
A 2
B 4
C 8
D 16
Answer D
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a UDL acting throughout its length and
rectangular cross section of b x d shows a deflection of 4 mm at the free end. If the same
UDL is applied throughout the length on another cantilever of the same material and
length but rectangular cross section of 2b x d, the deflection at the free end will
be________mm.
A 1
B 2
C 4
D 8
Answer B
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a UDL acting throughout its length and
rectangular cross section of b x d shows a deflection of 4 mm at the free end. If the same
UDL is applied throughout the length on another cantilever of the same material and
length but rectangular cross section of b x 2d, the deflection at the free end will
be________mm.
A 0.5
B 2
C 4
D 8
Answer A
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a UDL acting throughout its length and
rectangular cross section of b x d shows a deflection of 4 mm at the free end. If the same
UDL is applied throughout the length on another cantilever of the same material and
length but rectangular cross section of 2b x 2d, the deflection at the free end will
be________mm.
A 0.25
B 2
C 4
D 8
Answer A
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a UDL acting throughout its length and
rectangular cross section of b x d shows a deflection of 4 mm at the free end. If the same
UDL is applied throughout the length on another cantilever of the same material but twice
the length and rectangular cross section of b x 2d, the deflection at the free end will
be________mm.
A 0.5
B 2
C 4
D 8
Answer D
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a UDL acting throughout its length and a
rectangular cross section of b x d shows a slope of 4 at the free end. If the same UDL is
applied throughout the length on another cantilever of the same material and length but
rectangular cross section of 2b x d, the slope at its free end will be _______.
A 1
B 2
C 4
D 8
Answer B
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a UDL acting throughout its length and a
rectangular cross section of b x d shows a slope of 4 at the free end. If the same UDL is
applied throughout the length on another cantilever of the same material and length but
rectangular cross section of b x 2d, the slope at its free end will be _______.
A 0.5
B 2
C 4
D 8
Answer A
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a UDL acting throughout its length and a
rectangular cross section of b x d shows a slope of 4 at the free end. If the same UDL is
applied throughout the length on another cantilever of the same material and length but
rectangular cross section of 2b x 2d, the slope at its free end will be _______.
A 0.25
B 2
C 4
D 8
Answer A
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a UDL acting throughout its length and a
rectangular cross section of b x d shows a slope of 4 at the free end. If the same UDL is
applied throughout the length on another cantilever of the same material but twice the
length and the rectangular cross section of b x 2d, the slope at its free end will be
_______.
A 0.5
B 2
C 4
D 8
Answer C
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa), 6 mm in length has a rectangular cross section
of width 60 mm x 100 mm depth is subjected to a point load of 10 kN at its length. The
slope at its free end will be __________ .
A 0.00167
B 0.00167 radian
C 0.72
D 0.72 radian
Answer B
Marks 2
Unit
Id
Question A simply supported beam of copper (E = 100 GPa) having a point load of 10 kN at its
centre shows a deflection of 1 mm at the centre. If the load of 20 kN is applied at the
centre of another simply supported beam of the same cross sectional dimensions, double
the length and of steel (E = 200 GPa), the deflection at the centre will be _________ mm.
A 1
B 2
C 4
D 8
Answer D
Marks 2
Unit
Id
Question A simply supported beam of steel (E = 200 GPa) having a point load at its centre and a
rectangular cross section of b x d shows a deflection of 4 mm at the centre. If the same
load is applied at the centre of another simply supported beam of the same material and
length but rectangular cross section of 2b x d,the deflection at the centre will be
_________ mm.
A 1
B 2
C 4
D 8
Answer B
Marks 2
Unit
Id
Question A simply supported beam of steel (E = 200 GPa) having a point load at its centre and a
rectangular cross section of b x d shows a deflection of 4 mm at the centre. If the same
load is applied at the centre of another simply supported beam of the same material and
length but rectangular cross section of b x 2d, the deflection at the centre will be
_________ mm.
A 0.5
B 2
C 4
D 8
Answer A
Marks 2
Unit
Id
Question A simply supported beam of steel (E = 200 GPa) having a point load at its centre and a
rectangular cross section of b x d shows a deflection of 4 mm at the centre. If the same
load is applied at the centre of another simply supported beam of the same material and
length but rectangular cross section of 2b x 2d, the deflection at the centre will be
_________ mm.
A 0.25
B 2
C 4
D 8
Answer A
Marks 2
Unit
Id
Question A simply supported beam of steel (E = 200 GPa) having a point load at its centre and a
rectangular cross section of b x d shows a deflection of 4 mm at the centre. If the same
load is applied at the centre of another simply supported beam of the same material but
twice the length and rectangular cross section of b x 2d, the deflection at the centre will be
_________ mm.
A 0.5
B 2
C 4
D 8
Answer C
Marks 2
Unit
Id
Question A simply supported beam of steel (E = 200 GPa), 4 m in length has a rectangular cross
section of width 60 mm x 100 mm depth is subjected to a point load of 10 kN at its centre.
The deflection at its centre will be ________ mm.
A 1.33
B 13.33
C 0.13
D 133.33
Answer B
Marks 2
Unit
Id
Question A rod of length 2 m and square cross section 100 mm x 100 mm elongates by 0.01 mm
when subjected to an axial load W. If the same rod is used as a simply supported beam
and subjected to the same load at its centre, the deflection at the centre will be
________mm.
A 0.01
B 10
C 1
D 4
Answer C
Marks 2
Unit
Id
Question A simply supported beam of steel (E = 200 GPa) having UDL acting throughout its length
shows a deflection of 4 mm at the centre. If the same UDL is applied on another simply
supported beam of the same cross sectional dimensions and length but of copper (E = 100
GPa), the deflection at the centre will be _________ mm.
A 0.5
B 2
C 4
D 8
Answer D
Marks 2
Unit
Id
Question A simply supported beam of copper (E = 100 GPa) having UDL acting throughout its
length shows a deflection of 4 mm at the centre. If the same UDL is applied on another
simply supported beam of the same cross sectional dimensions and length but of steel (E
= 200 GPa), the deflection at the centre will be _________ mm.
A 1
B 2
C 4
D 8
Answer B
Marks 2
Unit
Id
Question A simply supported beam of copper (E = 100 GPa) having UDL of 10 kN / m acting
throughout its length shows a deflection of 4 mm at the centre. If the same UDL of 20
kN / m is applied throughout the length on another simply supported beam of the same
cross sectional dimensions and length but of steel (E = 200 GPa), the deflection at the
centre will be _________ mm.
A 1
B 2
C 4
D 8
Answer C
Marks 2
Unit
Id
Question A simply supported beam of copper (E = 100 GPa) having UDL of 10 kN / m acting
throughout its length shows a deflection of 4 mm at the centre. If the same UDL of 20
kN / m is applied throughout the length on another simply supported beam of the same
cross sectional dimensions and length but of steel (E = 200 GPa), the deflection at the
centre will be _________ mm.
A 2
B 4
C 8
D 16
Answer D
Marks 2
Unit
Id
Question A simply supported beam of steel (E = 200 GPa) having a UDL acting throughout its
length and a rectangular cross section of b x d shows a deflection of 4 mm at the centre. If
the same UDL is applied throughout the length on another simply supported beam of the
same material and length but rectangular cross section of 2b x d,the deflection at the
centre will be _________ mm.
A 1
B 2
C 4
D 8
Answer B
Marks 2
Unit
Id
Question A simply supported beam of steel (E = 200 GPa) having a UDL acting throughout its
length and a rectangular cross section of b x d shows a deflection of 4 mm at the centre. If
the same UDL is applied throughout the length on another simply supported beam of the
same material and length but rectangular cross section of b x 2d,the deflection at the
centre will be _________ mm.
A 0.5
B 2
C 4
D 8
Answer A
Marks 2
Unit
Id
Question A simply supported beam of steel (E = 200 GPa) having a UDL acting throughout its
length and a rectangular cross section of b x d shows a deflection of 4 mm at the centre. If
the same UDL is applied throughout the length on another simply supported beam of the
same material and length but rectangular cross section of 2b x 2d,the deflection at the
centre will be _________ mm.
A 0.25
B 2
C 4
D 8
Answer A
Marks 2
Unit
Id
Question A simply supported beam of steel (E = 200 GPa) having a UDL acting throughout its
length and a rectangular cross section of b x d shows a deflection of 4 mm at the centre. If
the same UDL is applied throughout the length on another simply supported beam of the
same material but twice the length and rectangular cross section of b x 2d, the deflection
at the centre will be _________ mm.
A 0.5
B 2
C 4
D 8
Answer D
Marks 2
Unit
Id
Question A cantilever of length L carries a load w uniformly distributed throughout its length. The
deflection at the free end is y1.Now the same cantilever carries the load W at its free end
and deflection at the free is y2. The ratio of y2/y1 is
A 3/8
B 3/4
C 4/3
D 8/3
Answer D
Marks 2
Unit
Id
Question A cantilever of length , diameter D carries a load W at its middle which produces a
deflection y1 , at the free end. Another cantilever of same material, length L but diameter
2D carries a load W at its middle which produces a deflection y2 at the free end . The
ratio of y2/y1 will be
A 8
B 4
C 1/4
D 1/16
Answer D
Marks 2
Unit
Id
Question A beam of length l, simply supported at the ends carries a point load W at its center .if EI
is flexural rigidity of the beam, strain energy due to bending is
A W2l3/48EI
B W2l3/96EI
C W3l2/48EI
D W3l3/96EI
Answer B
Marks 2
Unit
Id
Question A beam of length l, simply supported at the ends carries a point load W at its center .if EI
is flexural rigidity of the beam, strain energy due to bending is
A W2l3/48EI
B W2l3/96EI
C W3l2/48EI
D W3l3/96EI
Answer B
Marks 2
Unit
Id
Question The simply supported beam 'A' of length l carries a central point load W. Another beam 'B'
is loaded with a uniformly distributed load such that the total load on the beam is W. The
ratio of maximum deflections between beams A and B is
A 5/8
B 8/5
C 5/4
D 4/5
Answer B
Marks 2
Unit
Id
Question Two simply supported beams A and B carry same loads. Beam A carries a point load at
the centre and beam B carries UDL over the entire span. Ratio of maximum slopes of
beam A to beam B will be
A 2:3
B 3:2
C 1:2
D 2:1
Answer B
Marks 2
Unit
Id
Question For a cantilever beam carrying a couple moment M0 at the free end, the deflection at the
free end is ________.
A M0 L2 / EI
B M0 L2 / 2EI
C 2M0 L2 / EI
D 0
Answer B
Marks 2
Unit
Id
Question For a cantilever beam carrying a couple moment M0 at the free end, the slope at the free
end is ________.
A M0 L / EI
B M0 L / 2EI
C 2M0 L / EI
D 0
Answer A
Marks 2
Unit
Id
Question For a simply supported beam AB of length L carrying a couple moment M0 at its centre,
the slope at the end points is ________.
A M0 / EI
B M0 L / 24 EI
C M0 L / EI
D M0 L2 / 24 EI
Answer B
Marks 2
Unit
Id
Question For a beam, as shown in the below figure, when the load W is applied in the centre of the
beam, the maximum deflection is
Answer A
Marks 1
Unit
Id
Question The strain energy stored in a body, when the load is gradually applied, is (where = Stress in
the material of the body, V= Volume of the body, and E = Modulus of elasticity of the material)
Answer D
Marks 1
Unit
Id
Question If the length of a cantilever carrying an isolated load at its free end is doubled, the deflection
of the free end will increase by
A 8
B 1/8
C 1/3
D 2
Answer A
Marks 1
Unit
Id
Question If the width b and depth d of a beam simply supported with a central load are interchanged,
the deflection at the centre of the beam will be changed in the ratio of
A b/d
B d/b
C (d/b)2
D (b/d)2
Answer D
Marks 1
Unit
Id
Question For the loading shown, determine the deflection at the free end.
A -Px(3L-x)/6EI
B Px2(3L-x)/6EI
C -Px(3L-x)/6EI
D -Px2(3L-x)/6EI
Answer D
Marks 2
Unit
Id
Question
The area under the curve as shown in Figure by arrow is called as:
A Modulus of elasticity
B Modulus of resistance
C Modulus of resilience
D Modulus of stress-strain
Answer C
Marks 1
Unit
Id
Question
A positeve
B Negative
C Zero
Answer C
Marks 1
Unit
Id
Question For a beam, as shown in the below figure, if origin is taken at left end, slpoe at right
support will be
A positeve
B Negative
C Zero
Answer A
Marks 1
Unit
Id
Question For a beam havng point load at midspan of support , as shown in the figure, deflection at
midspan will be
Answer B
Marks 1
Unit
Id
Question For a beam, as shown in the figure, deflection at support will be
A Positive
B Negetive
C Zero
D All of above
Answer C
Marks 1
Unit
Id
Question For a beam, as shown in the figure, deflection at free end will be
A Positive
B Negetive
C Zero
D All of above
Answer B
Marks 1
Unit
Id
Question For a beam, as shown in the figure, deflection at free end will be
D All of above
Answer B
Marks 1
Unit
Id
Question A cantilever of length 4 meter carries a uniformly distributed load w throughout its length.
If the maximum bending moment in the cantilever is 8 N-m and EI is its flexural rigidity,
the slope at free end of the cantilever is ....
A 64/3EI
B 32/3EI
C 8/3EI
D None of these
Answer B
Marks 2
Unit
Id
Question A cantilever beam has a point load acting at its free end. The deflection at the free end is
observed to be 1 mm for a load of 10 kN. The deflection at the free end for a load of 20
kN will be __________ mm.
A 1
B 2
C 0.5
D 4
Answer B
Marks 2
Unit
Id
Question A cantilever beam has a point load acting at its free end. The deflection at the free end is
observed to be 1 mm for a load of 10 kN. The deflection at the free end for a load of 5 kN
will be __________ mm.
A 1
B 2
C 0.5
D 4
Answer C
Marks 2
Unit
Id
Question A cantilever beam of length 1 m having a point load at its free end shows a deflection of 4
mm at the free end. If the same load is applied on the free end of another cantilever of the
same cross-sectional dimensions but of length 2 m, the deflection at its free end will be
__________.
A 0.5
B 2
C 4
D 32
Answer D
Marks 2
Unit
Id
Question A cantilever beam of length 1 m having a point load at its free end shows a deflection of 4
mm at the free end. If the same load is applied on the free end of another cantilever of the
same cross-sectional dimensions but of length 2 m, the deflection at its free end will be
__________.
A 0.5
B 2
C 4
D 32
Answer A
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa ) having a point load at its free end shows a
deflection of 4 mm at the free end. If the same load is applied on the free end of another
cantilever of the same cross-sectional dimensions and length but of copper (E = 100 GPa),
the deflection at its free end will be __________mm.
A 0.5
B 2
C 4
D 8
Answer D
Marks 2
Unit
Id
Question A cantilever beam of copper (E = 100 GPa) having a point load at its free end shows a
deflection of 4 mm at the free end. If the same load is applied on the free end of another
cantilever of the same cross-sectional dimensions and length but of steel (E = 200 GPa ),
the deflection at its free end will be __________mm.
A 1
B 2
C 4
D 8
Answer B
Marks 2
Unit
Id
Question A cantilever beam of copper (E = 100 GPa) having a point load of 10 kN at its free end
shows a deflection of 4 mm at the free end. If the load of 20 kN is applied on the free end
of another cantilever of the same cross-sectional dimensions and length but of steel (E =
200 GPa ), the deflection at the free end will be __________mm.
A 1
B 2
C 4
D 8
Answer C
Marks 2
Unit
Id
Question A cantilever beam of copper (E = 100 GPa) having a point load of 10 kN at its free end
shows a deflection of 1 mm at the free end. If the load of 20 kN is applied on the free end
of another cantilever of the same cross-sectional dimensions and length but of steel (E =
200 GPa ), the deflection at the free end will be __________mm.
A 1
B 2
C 4
D 8
Answer D
Marks 2
Unit
Id
Question A cantilever beam has a point load acting at its free end. The slope at the free end is
observed to be 1 for a load of 10 kN. The slope at the free end for a load of 20 kN will be
_________.
A 1
B 2
C 0.5
D 4
Answer B
Marks 2
Unit
Id
Question A cantilever beam has a point load acting at its free end. The slope at the free end is
observed to be 1 for a load of 10 kN. The slope at the free end for a load of 5 kN will be
_________.
A 1
B 2
C 0.5
D 4
Answer C
Marks 2
Unit
Id
Question A cantilever beam has a UDL acting throughout its length. The deflection at the free end
is observed to be 1 mm for a UDL of 10 kN/m. The deflection at the free end for a UDL
of 20 kN/m will be _______mm.
A 1
B 2
C 0.5
D 4
Answer B
Marks 2
Unit
Id
Question A cantilever beam has a UDL acting throughout its length. The deflection at the free end
is observed to be 1 mm for a UDL of 10 kN/m. The deflection at the free end for a UDL
of 5 kN/m will be _______mm.
A 1
B 2
C 0.5
D 4
Answer C
Marks 2
Unit
Id
Question A cantilever beam of length 1 m having a UDL throughout its length shows a deflection
of 1 mm at the free end. If the same UDL is applied on another cantilever of the same
cross sectional dimensions but of length 2 m throughout the length, the deflection at its
free end will be________mm.
A 2
B 4
C 16
D 32
Answer C
Marks 2
Unit
Id
Question A cantilever beam of length 1 m having a UDL throughout its length shows a deflection
of 4 mm at the free end. If the same UDL is applied on another cantilever of the same
cross sectional dimensions but of length 0.5 m throughout the length, the deflection at its
free end will be________mm.
A 0.5
B 0.25
C 4
D 32
Answer B
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a UDL acting throughout its length
shows a deflection of 4 mm at the free end. If the same UDL is applied on another
cantilever of the same cross sectional dimensions and length but of copper (E = 100 GPa),
the deflection at the free end will be________mm.
A 0.5
B 2
C 4
D 8
Answer D
Marks 2
Unit
Id
Question A cantilever beam of copper (E = 100 GPa) having a UDL acting throughout its length
shows a deflection of 4 mm at the free end. If the same UDL is applied on another
cantilever of the same cross sectional dimensions and length but of steel (E = 200 GPa),
the deflection at the free end will be________mm.
A 1
B 2
C 4
D 8
Answer B
Marks 2
Unit
Id
Question A cantilever beam of copper (E = 100 GPa) having a UDL of 10 kN / m acting throughout
its length shows a deflection of 4 mm at the free end. If the UDL of 20 kN / m is applied
throughout the length on another cantilever of the same cross sectional dimensions and
length but of steel (E = 200 GPa), the deflection at the free end will be________mm.
A 1
B 2
C 4
D 8
Answer C
Marks 2
Unit
Id
Question A cantilever beam has a UDL acting throughout its length. The slope at the free end is
observed to be 1 for a UDL of 10 kN / m. The slope at the free end for a UDL of 20 kN /
m will be _______.
A 1
B 2
C 0.5
D 4
Answer B
Marks 2
Unit
Id
Question A cantilever beam has a UDL acting throughout its length. The slope at the free end is
observed to be 1 for a UDL of 10 kN / m. The slope at the free end for a UDL of 5 kN /
m will be _______.
A 1
B 2
C 0.5
D 4
Answer C
Marks 2
Unit
Id
Question A cantilever beam of length 1 m having a UDL acting throughout its length shows a slope
of 1 at the free end. If the same UDL is applied throughout the length on another
cantilever of the same cross sectional dimension but of length 2 m, the slope at its free
end will be _______.
A 0.5
B 2
C 4
D 8
Answer D
Marks 2
Unit
Id
Question A cantilever beam of length 1 m having a UDL acting throughout its length shows a slope
of 4 at the free end. If the same UDL is applied throughout the length on another
cantilever of the same cross sectional dimension but of length 0.5 m, the slope at its free
end will be _______.
A 0.5
B 2
C 4
D 8
Answer A
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa) having a UDL acting throughout its length
shows a slope of 4 at the free end. If the same UDL is applied throughout the length on
another cantilever of the same cross section dimensions and length but of copper (E = 100
GPa) , the slope at its free end will be _______.
A 0.5
B 2
C 4
D 8
Answer D
Marks 2
Unit
Id
Question A cantilever beam of copper (E = 100 GPa) having a UDL acting throughout its length
shows a slope of 4 at the free end. If the same UDL is applied throughout the length on
another cantilever of the same cross section dimensions and length but of steel (E = 200
GPa) , the slope at the free end will be _______.
A 1
B 2
C 4
D 8
Answer B
Marks 2
Unit
Id
Question A cantilever beam of copper (E = 100 GPa) having a UDL of 10 kN / m acting throughout
its length shows a slope of 4 at the free end. If the UDL of 20 kN / m is applied
throughout the length on another cantilever of the same cross section dimensions and
length but of steel (E = 200 GPa) , the slope at the free end will be _______.
A 1
B 2
C 4
D 8
Answer C
Marks 2
Unit
Id
Question A cantilever beam of copper (E = 100 GPa) having a UDL of 10 kN / m acting throughout
its length shows a slope of 1 at the free end. If the UDL of 20 kN / m is applied
throughout the length on another cantilever of the same cross sectional dimensions,
double the length and of steel (E = 200 GPa) , the slope at the free end will be _______.
A 1
B 2
C 4
D 8
Answer D
Marks 2
Unit
Id
Question A cantilever beam of steel (E = 200 GPa), 1 m in length has a rectangular cross section of
width 60 mm x 100 mm depth is subjected to a UDL of 10 kN / m throughout its length.
The deflection at its free end will be __________ mm.
A 1.25
B 0.72
C 0
D 5.2
Answer A
Marks 2
Unit
Id
Question A simply supported beam has a point load acting at its centre. The deflection at the centre
is observed to be 1 mm for a load of 10 kN. The deflection at the centre for a load of 20
kN will be ______mm.
A 1
B 2
C 0.5
D 4
Answer B
Marks 2
Unit
Id
Question A simply supported beam has a point load acting at its centre. The deflection at the centre
is observed to be 1 mm for a load of 10 kN. The deflection at the centre for a load of 5 kN
will be ______mm.
A 1
B 2
C 0.5
D 4
Answer C
Marks 2
Unit
Id
Question A simply supported beam of length 1 m having a point load acting at its centre shows a
deflection of 4 mm at the centre. If the same load is applied at the centre of another
simply supported beam of the same cross sectional dimensions but of length 2 m, the
deflection at its centre will be ______mm.
A 0.5
B 2
C 4
D 32
Answer D
Marks 2
Unit
Id
Question A simply supported beam of length 1 m having a point load acting at its centre shows a
deflection of 4 mm at the centre. If the same load is applied at the centre of another
simply supported beam of the same cross sectional dimensions but of length 0.5 m, the
deflection at its centre will be ______mm.
A 0.5
B 2
C 4
D 32
Answer A
Marks 2
Unit
Id
Question A simply supported beam of steel (E = 200 GPa) having a point load at its centre shows a
deflection of 4 mm at the centre. If the same load is applied at the centre of another
simply supported beam of the same cross sectional dimensions and length but of copper
(E = 100 GPa), the deflection at the centre will be _________ mm.
A 0.5
B 2
C 4
D 8
Answer D
Marks 2
Unit
Id
Question A simply supported beam of copper (E = 100 GPa) having a point load at its centre shows
a deflection of 4 mm at the centre. If the same load is applied at the centre of another
simply supported beam of the same cross sectional dimensions and length but of steel (E
= 200 GPa), the deflection at the centre will be _________ mm.
A 1
B 2
C 4
D 8
Answer B
Marks 2
Unit
Id
Question A simply supported beam of copper (E = 100 GPa) having a point load of 10 kN at its
centre shows a deflection of 4 mm at the centre. If the load of 20 kN is applied at the
centre of another simply supported beam of the same cross sectional dimensions and
length but of steel (E = 200 GPa), the deflection at the centre will be _________ mm.
A 1
B 2
C 4
D 8
Answer C
Marks 2
Unit
Id
Question A simply supported beam has a UDL acting throughout its length. The deflection at the
centre is observed to be 1 mm for a UDL of 10 kN / m. The deflection at the centre for a
UDL of 20 kN / m will be ______mm.
A 1
B 2
C 0.5
D 4
Answer B
Marks 2
Unit
Id
Question A simply supported beam has a UDL acting throughout its length. The deflection at the
centre is observed to be 1 mm for a UDL of 10 kN / m. The deflection at the centre for a
UDL of 5 kN / m will be ______mm.
A 1
B 2
C 0.5
D 4
Answer C
Marks 2
Unit
Id
Question A simply supported beam of length 1 m having UDL acting throughout its length shows a
deflection of 1 mm at the centre. If the same UDL is applied at the centre of another
simply supported beam of the same cross sectional dimensions but of length 2 m
throughout the length, the deflection at its centre will be ______mm.
A 2
B 4
C 16
D 32
Answer C
Marks 2
Unit
Id
Question A simply supported beam of length 1 m having UDL acting throughout its length shows a
deflection of 4 mm at the centre. If the same UDL is applied at the centre of another
simply supported beam of the same cross sectional dimensions but of length 0.5 m
throughout the length, the deflection at its centre will be ______mm.
A 0.5
B 0.25
C 4
D 32
Answer B
Marks 2
Unit
Id
Question A beam simply supported at its ends over a span of 4 meters carries uniformly distributed
load of 1.5 kN/m run through out its length. If EI = 5000 kN-m2, the max. deflection in
the beam is.
A 1 mm
B 2 mm
C 2.5 mm
D None of these
Answer A
Marks 2
Unit
Id
Question A round bar A of diameter D and length L is subjected to an axial stress f. Another round
bar B of the same material , diameter 2D and length 0.25L is also subjected to the same
axial stress f. the ratio of strain energy in bar A to the the strain energy in bar B is
A 4
B 2
C 1
D 0.25
Answer C
Marks 2
Unit
Id
Question A simply supported beam of length 2 meters carries a concentrated load of 3 kN at its
center. If EI=500 kN-m2 for the beam the maximum deflection in the beam is
A 16 mm
B 5 mm
C 2 mm
D 1 mm
Answer D
Marks 2
Unit
Id
Question A simply supported beam of 6 m carries a concentrated load W at its center such that
bending moment M. at the center of beam is 6 kN-m. If EI is the flexural rigidity of the
beam, then deflection at the center is
A 36/EI
B 27/EI
C 18/EI
D 9/EI
Answer C
Marks 2
Unit
Id
Question A simply supported beam of rectangular section breadth=b and depth d=2b carries a load
w at one third of its length producing deflection y under the load. Now the beam is turned
with depth=b and breadth=2b, the deflection under the load will be
A 6y
B 4y
C 2y
D 1/4y
Answer B
Marks 2
Unit
Id
Question A beam of simply supported over 10 m carries a uniformly distributed load 1 kN/m
throughout its length. If EI is 5000 kN-m2 then the maximum deflection y is
A 26 mm
B 52 mm
C 2.6 mm
D 10 mm
Answer A
Marks 2
Unit
Id
Question The ratio of the maximum deflections of a beam simply supported at its ends with an
isolated central load and that of with a uniformly distributed load over its entire length, is
A 1
B
Answer C
Marks 2
Unit
Id
Question A cantilever beam rectangular in cross-section is subjected to an isolated load at its free
end. If the width of the beam is doubled, the deflection of the free end will be changed in
the ratio of
A 8
B 1/8
C 1/2
D 2
Answer C
Marks 2
Unit
Id
Question If the width of a simply supported beam carrying an isolated load at its center is doubled,
the deflection of the beam at the center is changed by
A 2 times
B 4 times
C 8 times
D 1/2 times
Answer C
Marks 2
Unit
Id
Question The ratio of the maximum deflection of a cantilever beam with an isolated load at its free
end and with a uniformly distributed load over its entire length, is
A 1
B
Answer D
Marks 2
Unit
Id
Question The deflection due to couple M at the free end of a cantilever length L is
Answer C
Marks 2
Unit
Id
Question A uniform girder simply supported at its ends is subjected to a uniformly distributed load
over its entire length and is propped at the centre so as to neutralize the deflection. The
net B.M. at the centre will be
A WL
B
Answer D
Marks 2
Unit
Id
Question The deflection of any rectangular beam simply supported, is
A directly proportional to its weight
B inversely proportional to its width
C inversely proportional to the cube of its depth
D directly proportional to the cube of its length
Answer C
Marks 2
Unit
Id
Question The energy stored in a beam of length L subjected to a constant B.M. is
A
Answer A
Marks 2
Unit
Id
Question A simply supported beam of length 4 m supports a UDL 2 kN/m over the entire span.
What will be the maximum slope assuming E = 200 GPa and I = 4 x 105 mm4
A 0.057 rad
B 0.067 rad
C 0.077 rad
D 0.087 rad
Answer B
Marks 2
Unit
Id
Question A simply supported beam of length 4 m supports a UDL 2 kN/m over the entire span.
What will be the maximum deflection assuming E = 200 GPa and I = 4 x 105 mm4
A 53.3 mm
B 63.3 mm
C 73.3 mm
D 83.3 mm
Answer D
Marks 2
Unit
Id
Question A simply supported beam of span 5 m supports a point load of 30 kN at a distance of 3.75
m from the left support A. The deflection under the load will be
A 1.7 mm
B 1.8 mm
C 1.9 mm
D 2.0 mm
Answer A
Marks 2
Unit
Id
Question Maximum deflection in simply supported beam of length 1m carying a concentrated load
20 kN at midspan is (take EI = 25,000 kN m2 )
A 0.0166mm
B 1.666mm
C 0.00166mm
D 1.666m
Answer A
Marks 2
Unit
Id
Question Maximum deflection in simply supported beam of length 2 m carying a concentrated load
20 kN at midspan is (take EI = 25,000 kN m2 )
A 0.133 mm
B 1.333 mm
C 0.00133 mm
D 1.333 m
Answer A
Marks 2
Unit
Id
Question A beam simply supported at ends over a span of 4 m, carries a udl of 15 kN/m throughout
its length. If EI = 25,000 kN m2, then the maximum deflection in beam is
A 2 mm
B 0.0002 m
C 0.02 mm
D 2m
Answer A
Marks 2
Unit
Id
Question The simply supported beam 'A' of length l carries a central point load W. Another beam 'B'
is loaded with a uniformly distributed load such that the total load on the beam is W. The
ratio of maximum deflections between beams A and B is
A 0.63
B 1.6
C 0.8
D 1.25
Answer B
Marks 2
Unit
Id
Question Which of the follwing is true
A Deflection of beam at any section at a distance x is change in arc length of ealstic curve
for that section