Sei sulla pagina 1di 12

1.

The capacitance of the capacitor in a fuel quantity indicator depend on


a) distance b/w the plates
b) area of the plates
c) dielectric constant of medium
d) all of the above

2. The capacitance of a capacitor depends on


a) type of dielectric
b) area of plates
c) distance between plates
d) all of the above

3. To convert a galvanometer into voltmeter


a) connecting high resistance in series
b) connecting low resistance in series
c) connecting low resistance in parallel

4. Electromagnetic induction depends on


a) no. of turns in the coil
b) speed of rotation
c) strength of permanent magnet
d) all of the above

5. In case of an isometric drawing


a) vertical lines are at an angle of 1200
b) vertical lines are vertical & horizontal lines at 30 0
c) vertical lines are vertical & horizontal lines at 600

6. Front, top and right side view correspond to


a) orthographic projection
b) isometric drawing
c) perspective drawing

7. Write the correct statement wrt MAC


a) it is an imaginary aerofoil in which all the forces act in the same way as they would
act on a wing surface
b) it is the average of all chords one foot a part
c) mean aerodynamic chord
d) all of the above

8. Which of the following are high lift devices


a) flaps & slats
b) flaps & boundary layer devices
c) slats & boundary layer devices
d) all of the above

9. An algorithm has
a) An input
b) An output
c) An assigned statement

10. Convert 11.75 to binary


a) 1011.10
b) 1101.11
c) 1011.11 d) 1110.10
11. The truth table corresponds to
A B V
0 0 0 a)
0 1 1 b)
1 0 1 c)
1 1 1 d)

12. Universal gates


a) AND & OR
b) NAND & NOR
c) XOR & EXNOR
d) None of the above

13. Triangular files are


a) Have safe edge
b) Tapered along 3 edges
c) Used to cut acute angles
d) Both b & c

14. Lift and drag depends upon


a) AOA increases Lift & drag both increases
b) drag depends upon frontal area only
c) lift depends on AOA only
d) all of the above

15. Delaminations in composites


a) are always visible
b) always accompanied by impact damage
c) cannot be detected by coin tap test
d) none of the above are correct

16. Ammeter is used for measuring


a) current supplied by a battery
b) current supplied by a generator
c) current during charging and discharging
d) current during charging and discharging when electrical requirement change

17. Lead acid battery electrolyte can be neutralized by


a) bicarbonate of soda
b) vinegar
c) boric acid
d) both b and c

18. Composition of Pb acid battery in a fully charged state is


a) 30% acid & 70% H2O by volume
b) 70% acid & 30% H2O by weight
c) 50% acid & 50% H2O by weight

19. Bonding is done during fuelling to


a) provide low resistance path
b) give way to stray current
c) dissipate static charge

20. Radiography depends upon


a) shape and size of object
b) nature of defect
c) film characteristics
d) all of the above

21. Ultrasonic test


a) ferrous
b) non-ferrous
c) all material
d) ceramic

22. when it is necessary to retighten a nut


a) retighten without backing of
b) retighten by backing off a single turn
c) retighten by backing off one flare portion

23. When it is required to turn the bolt head instead of nut


a) max. torque range increases
b) max. torque range decreases
c) max. torque range remains same

24. What is the purpose of flux in soldering


a) to remove metallic oxide
b) to provide more penetration of solder
c) for free flow solder
d) all of the above

25. Vortex generator is used for


a) high speed characteristics of wing surface
b) low speed characteristics of tail plaine
c) low speed characteristics of wing surface
d) both a and b

26. Co-efficient of lift depends upon


a) shape and area of aerofoil
b) shape of aerofoil and angle of attack
c) shape of aerofoil only
d) camber of wing upper surface

27. Hi tigue fasteners


a) can replace solid shank rivets of same dia
b) can replace solid shank rivets of one dia larger
c) can replace solid shank rivets of one dia smaller

28. Chord line is


a) curved line joining wing LE to TE
b) straight line joining wing LE to TE
c) max upper camber
d) line joining from wingtip to wingtip

29. Negative dihedral is employed in a/c to


a) to impart lateral stability
b) to improve the high speed characteristics
c) to generate more lift
d) counteract the efects of excessive lateral stability
30. Anodized Al is cleaned by using
a) steel wool
b) sand paper
c) Al wool
d) Carbide embedded paper

31. If the power drawn by a load at a supply voltage of 28V is 20W then the line resistance is
a) 78.4
b) 28
c) 82 d) 28.82
32. Triode consists of
a) plate cathode & heater
b) plate, cathode, tube
c) plate, cathode, heater & a wire mesh between plate & cathode

33. Carbon fibre is anisotropic. This means :


a) the molecules are distributed linearly
b) molecules are in aligned thus physical properties are diferent in all
directions

34. Junction diode is not used as an a :


a) rectifier
b) source of light
c) for detecting the intensity of light
d) as an amplifier

35. When bolts are rivets are used side by side


a) they are protected by greasing
b) they are plated for protection
c) they are lubricated for cooling

36. Failure by fatigue is identified by


a) marks that extend at 900 to loads imposed
b) marks that are symmetrical
c) marks that are at an angle to the part failed

37. Before DPT parts are cleaned using


a) kerosene oil
b) petrol
c) soap and detergent

38. To check a circuit for continuity it must be


a) connected to a power source
b) connected to a battery
c) isolated
d) both a and b

39. Tooth thickness of a gear is measured by


a) vernier micrometer
b) vernier caliper
c) at the point where pitch circle cuts the teeth
d) vernier micrometer & vernier caliper

40. A Bevel gear transmits motion


a) at an angle
b) perpendicularly
c) parallely
d) reduces speed

41. In a spur gear


a) diametrical pitch is equal to pitch diameter
b) PD/DP gives size of teeth
c) Teeth are cut ut an angle to the axis

42. Elastomer is
a) rubber tires
b) metal sheets impregnated with rubber
c) rubber containing metal chips for bonding

43. In a micrometer
a) anuil & barrel moving spindle moving
b) anvil & barrel stationary spindle movable
c) frame rotatable spindle stationary

44. In case of swaged fitting


a) if lesser the dia the fitting is overswaged
b) fitting must be rejected
c) lesser the dia the fitting is underswaged
d) both a and b

45. Information required in a blue print is


a) TPI, major dia, grip length , material , depth
b) Pitch dia, minor dia, TPI
c) Major dia, minor dia, TPI

46. Modern computers use


a) Binary system
b) Decimal system
c) Octal system
d) Hexadecimal system

47. A semiconductor possesses


a) infinite resistance at 00C
b) finite resistance which with temp
c) finite resistance which with temp

48. CRS consists of


a) 18 % Cr and 8% Ni
b) 18% Ni and 8% Cr
c) 20% Ni , 2% P and 8% Cr

49. Peizoelectric effect


a) quartz crystal & Rochelle salt
b) semi conductors
c) freq. depends on thickness of crystal
d) both a and c

50. Inductance depends on :


a) AC or DC (Type of current)
b) No. of turns in the coil
c) All

51. A gyro having 3 degrees of freedom and 3 mutually 1 axes :


a) space or free gyro
b) rate gyro
c) turn gyro

52. As the speed of a/c


a) static pr
b) dynamic pressure
c) both static & dynamic pr
d) static pr Dynamic pr

53. All purpose rust preneutine compound is


a) paralketone
b) lubricating oil
c) grease

54. An 310 is used with


a) clevis bolts
b) undrilled shank bolts
c) hexhead bolts

55. Pitch dia of a gear is equal to


a) AXN

56. Resistance of a straight conductor does not depends on


a) shape of cross section
b) material
c) length

57. Screw threads


a) square threads have equal width and height distance b/w the threads is also same
b)
c
d)all
58. Flap increases
a) camber
b) angle of attack
c) none

59. Rockwell testing


a) lesser the Rockwell number harder the material
b) lesser the Rockwell number softer the material
c) dia of the ball
PAPER-II (FEB-2008)
1. Convert these number in binary of 11.75:
a) 1101.11
b) 1011.11
c) 1010.11
d) 1001.10

2. For neutralize the Pb-acid battery spillage with:


a) Sodium bicarbonate/backing soda
b) Boric acid and as in (a)
c) Vinegar
d) All of the above

3. Piezoelectric effect is caused on:


a) Quartz
b) Rochellsalt
c) As in (a) & (b) are correct

4. Function of slat & flap:


a) To increase the speed of A/c
b) To decrease the take off & landing run
c) As in (b) & is used in high speed operation
d) As in (b) & also to reduce the fuel consumption

5. In pure semi-conductor having resistance:


a) Infinite resistance at 0C
b) Finite resistance with increase in temperature
c) Finite resistance with decrease in temperature

6. Language of computer is:


a) Decimal
b) Octal
c) Binary

7. Titanium is:
a) Having more U.T.S. than Al & stainless steel
b) Having light wt. & high strength & corrosion resistance in salt water
c) High strength-to-weight ratio
d) All of the above

8. In florescent penetrate inspection the defects will show:


a) Brilliant yellow & green color in black light
b) Deep blue violet
c) None

9. Capacitor plate in a capacitor type fuel quantity gauge depends upon:


a) Directly proportional of plate area
b) Inversely proportional with distance b/w the plates
c) Type of dielectric material
d) All are correct

10. Pn Zn diode does not used as a:


a) Light intensity
b) Rectifier
c) Amplify the sc signals/transformer & light radiations

11. Bevel gear is used for:


a) Transmission of load b/w shaft at an angles to each other
b) For variation of speed
c) In speed reducer
d) All are correct

12. Circular magnetization method used in MPI correct detect which type of defect:
a) Longitudinal cracks
b) Deep sub surface
c) Lateral cracks
d) Torsional cracks on a shaft

13. 7 x 19 cable indicates:


a) 7 strands of 19 wires each
b) 19 strands of 7 wires each
c) 7 strands of 19 mm wires each

14. Microprocessor at least consists of:


a) CPU
b) Memory
c) Arithmetic logic unit
d) All are correct

15. The greatest size drill amongst the following is:


a) No. 1
b) No. 30
c) 3/16
d) E

16. Find the micrometer reading from the given diagram:


a) 0.4699
b) 0.4569
c) 0.4692

17. The primary cause of inter granular corrosion is:


a) Dissimilar metal contact
b) Improper heat treatment
c) Due to non-metal & metal contact
d) Due to corrosive gases

18. Weft threads are:


a) At 45 to warp threads
b) Perpendicular to warp threads
c) Along with the warp threads to form the edge
d) None are correct

19. Rigid tubing in the a/c are classified according to:


a) Outside diameter
b) Wall thickness & outside diameter
c) Inside diameter & wall thickness
d) Inside diameter
20. 4 in a circuit the resistance is R & reactance is r then impedance Z is expressed as:
a) Z = R + r
b) Z = R + r
c) 1/Z = 1/R + 1/r
d) Z2 = R2 + r2
21. The given figure indicates:
a) X NOR gate
b) X OR gate
c) C MOS NOR gate
d) NOR gate

22. Calculate the power when voltage = 28 volts & Resistance = 10


a) 28.4W
b) 784W
c) 78.4W
d) 7.84W

23. In steady & level flight, if the angle of attack increases:


a) Lift increases
b) Drag increases
c) Lift increases & drag decreases
d) Lift & drag both decreases

24. In straight & level flight, the dynamic pressure qeting on the tip of nose of the a/c is:
a) Maximum
b) Minimum
c) Zero
d) None of the above

25. In pitat static system, the static pressure is sensed at two points by placing flat plates on
either side of fuselage:
a) Eliminates position error
b) Freedom from ice formation
c) Eliminates static & instrument error
d) Both (a) & (b) are correct

26. In ATA 100 specification, the codes for hydraulic, pneumatic five protection system &
engine indicating system are:
a) 29, 26, 39, 77
b) 29, 36, 26, 77
c) 36, 26, 29, 79
d) 29, 71, 36, 27

27. Fatigue over a man is caused due to:


a) Long hours of work
b) Emotional stress
c) Noise
d) All of the above

28. Static discharge wicks is mentioned in which chapter of maintenance manual:


a) Chapter number 22
b) Chapter number 23
c) Chapter number 24
d) Chapter number 25
29. Elevator is used to:
a) For lateral control
b) Rotate a/c around lateral axis
c) Establish a/c about lateral axis
d) Both (b) & (c) are correct
30. Angle of incidence is defined as:
a) Angle b/w longitudinal axis & relative wind
b) Angle b/w longitudinal axis & chord line
c) Angle b/w chord line & relative wind
d) None of the above

31. Torque tube is:


a) Act as rotating member in cable system
b) Compression & tension both load can withstand
c) Used along with bell crank
d) Convert rotary motion along with bell crank

32. In an electrical ckt. If capacitance is 100 microfarad & charge is 1 micro colomb, then
voltage rating would be:
a) 100 V
b) 10 V
c) 1 V
d) 1000 V

33. Given figure indicate:


a) Splined shaft
b) Meshing gear
c) Gear & pinion

34. Given figure indicate:


a) Double pole double throw
b) Double pole single throw
c) Single pole double throw
d) Push pull s/w

35. Given figure indicates:


a) Bucking bar not held properly
b) Excessive drive
c) Upset head

36. If one wheel is be jacked:


a) Tripod jack is used
b) Remaining wheel should be chocked
c) Wheel raised should be raised by 6 to 8

37. Shunt a/c motor is used to drive:


a) Landing gear
b) Gyro & servo motor
c) Flap

38. Ac motor is used in respect of DC motor or advantage of a/c motor over DC motor:
a) Less weight
b) Less manufacturer cost & maintenance
c) Brush & commutator is not used in A.C. motor
39. In A/c seeps in fuel tank is specified by:
a) Low seep, seep, heavy seep
b) Stone, low seep, heavy seep, running leak
c) Running leak, leak
d) All of the above

40. Annealing of steel is done for:


a) Maximum ductility
b) Softness
c) Low strength
d) All of the above

41. High resistance load in electrical ckt. Is checked by:


a) AVM meter in DC ohm
b) DC battery with lamp
c) Maneto synchronizer
d) Both (b) & (c)

42. In given figure of welding is indicates:


a) V-weld
b) U-weld
c) Double beveled weld
d) J-weld

43. Conductor having 4 resistance, stretched twice in length then new would be:
a) 4
b) 8
c) 16
d) 12

44. Titanium is heat treated to:


a) Relief internal stresses
b) Annealing for further cold working
c) Thermal hardening to improve
d) All of the above

45. If two battery A & B such that A having greater plate area than B, then internal
resistance of A will be:
a) Greater than B
b) Smaller than B
c) Equal to B
d) None

46. MTCS:
a) In nacelle it is measured from the front spar of the wing
b) Water line measure height in inches in parallel to the horizontal plane
c) Butt line measures width from left to right, parallel to the vertical plane
d) All of the above

47. Hose colour of 100 LL fuel is identified by:


a) Red band
b) Black band
c) Red band green strip
d) Black band yellow strip
48. Colour of fuel line is:
a) Red colour
b) Black
c) Brown

49. MTCS:
a) Reed & prince s/w driver having blunt point
b) Phillips s/w driver is blunt
c) Phillips s/w driver having pointed

50. Kirchoffs law is applicable for:


a) A.C. ckt.
b) D.C. ckt.
c) Both A.C. & D.C. ckt
d) Both A.C. & D.C. excluded capacitive & inductive element

51. Fatigue crack detected by:


a) Ultrasonic
b) Magnetic particle inspection
c) Eddy current
d) All of the above

52. In composite impact damage & water disbond is inspected by:


a) Thermal halo graph
b) Laser halo graph
c) Ultrasonic
d) X-ray

Potrebbero piacerti anche