Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
DIVISION 3 CONCRETE
DIVISION 4 MASONRY
DIVISION 5 METALS
DIVISION 9 FINISHES
DIVISION 10 SPECIALTIES
DIVISION 11 EQUIPMENT
DIVISION 12 FURNISHINGS
Furniture Specifications
Table of Contents i
Space Standards and Typicals 1.1 to 1.8
Furniture Code Index 2.1 to 2.2
Furniture Catalog Cuts 3.1 to 3.223
Furniture Location Details 4.1 to 4.193
Room Furniture Details 5.1 to 5.158
List of Manufacturers 7.1 to 7.8
DIVISION 15 MECHANICAL
Section 15350 Automatic Deluge Foam Water Sprinkler / Spray Systems 15350-1 - 8
Section 15390 Clean Agents Fire Extinguishing Systems 15390-1 - 9
Section 15400 Plumbing Systems 15400-1 - 7
Section 15410 Plumbing Piping 15410-1 - 20
Section 15420 Water Storage Tanks and Accessories 15420-1 - 10
Section 15430 Plumbing Specialities 15430-1 - 14
Section 15440 Sanitary Fixtures 15440-1 - 7
Section 15450 Plumbing Equipment 15450-1 - 11
Section 15480 Liquid Fuel Storage and Transfer 15480-1 - 17
Section 15500 Heating, Ventilating and Air-conditioning Systems 15500-1 - 17
Section 15510 Hydronic piping 15510-1 - 13
Section 15530 Hydronic Specialities 15530-1 - 6
Section 15540 Hydronic Pumps 15540-1 - 5
Section 15545 Hydronic Water Treatment 15545-1 - 6
Section 15550 Packaged Water Cooled Liquid Chillers 15550-1 - 16
Section 15560 Cooling Towers 15560-1 - 13
Section 15570 Hydronic Boilers 15570-1 - 10
Section 15600 Direct Expansion Air-Conditioning Units 15600-1 - 7
Section 15630 Refrigerant Piping and Specialities 15630-1 - 7
Section 15650 Air Cleaning Devices 15650-1 - 5
Section 15660 Humidifiers 15660-1 - 3
Section 15670 Fans 15670-1 - 8
Section 15680 Air Coils 15680-1 - 4
Section 15690 Energy Recovery Systems 15690-1 - 8
Section 15700 Air Handling Units 15700-1 - 13
Section 15710 Power Ventilators 15710-1 - 6
Section 15740 Variable Air Volume Devices 15740-1 - 6
Section 15750 Ductwork 15750-1 - 7
Section 15760 Ductwork Accessories 15760-1 - 6
Section 15770 Ductwork Insulation 15770-1 - 4
Section 15780 Sound Attenuators 15780-1 - 3
Section 15790 Air Outlets and Inlets 15790-1 - 6
Section 15800 HVAC Controls 15800-1 - 11
Section 15810 Automatic Control Sequence 15810-1 - 7
Section 15850 Building Management Systems 15850-1 - 40
Section 15900 Testing, Adjusting and Balancing 15900-1 - 9
Section 15950 Proposed Equipment and Materials for HVAC Systems 15950-1 - 19
DIVISION 16 ELECTRICAL
FURNITURE
PART 1- GENERAL
A. The drawings and general provisions of the contract, including General and
Particular Conditions and Division 1 Specification Sections, are included for
reference in this specification section.
B. Refer to Furniture drawings, etc. for the furniture layout at various locations.
A. All sections affected by this section and all sections affecting this section shall be
considered Related Sections
B. Basis of Design.
1. The first furniture item listed for each type of furnishing is the Basis of
Design. Other acceptable manufacturers follow. These other
manufacturers may or may not involve slight modifications to the layout or
infrastructure. All costs associated with such modifications shall be the
responsibility of this furniture package provider.
2. The Contractor can price for either recommended product or Alternate 1 or
Alternate 2.
3. Furniture substitutions are not acceptable.
4. Fabric substitutions are not acceptable.
B. Shop Drawings: Include detailed layout plans of each floor level, elevations, 3-
Dimensional drawings of each typical workstation or office with identification of
associated finishes. The manufacturer will work closely with the Engineer to
develop a more detailed layout based on the furniture plans contained herein. For
any specified products that have modifications, special or custom features
provide appropriate notes on shop drawings. Fabrication shall not commence until
approval has been given by the Engineer. Show complete details of fabrication.
Include all dimensions and any related field dimensions. Show complete
assemblies and connections. Note finishes and materials. Include any
manufacturers design or assembly concerns or comments, if any, on shop
drawings.
C. Operating and Maintenance Data: For each item provide data regarding operating,
adjusting, repairing, and replacing systems and/or office furniture as outlined in
Division 1.
D. Provide draft warranties as listed in Clause 1.06 WARRANTY below for each
furnishing item.
C. Fabrication & Construction: All work is subject to specified Premium level of quality
from appropriate reference standards; any reference to a quality level in these
Specifications defined in the referenced standard shall be considered a part of
these Specifications. Any work not specified with a level of quality shall be not less
than Premium quality.
D. Coordinate fabric utilization such that when the same fabric is used on separate
furniture items, it is from the same dye lot.
A. Coordinate the delivery of product with the Engineer. Do not deliver systems
furniture or office furniture until spaces to receive them are clean, dry, and ready
for installation.
1.06 WARRANTY
A. General Warranty: Special warranty specified in this Article shall not deprive the
Owner of other rights Owner may have under the other provisions of the Contract
Documents and shall be in addition to, and run concurrent with, other warranties
made by the Contractor under the requirements of the Contract Documents.
PART 2- PRODUCTS
A. This specification establishes the minimum product requirements for all materials
required for the installation of a complete and usable system of free-standing
workstations, panels, and office furniture.
B. Typical workstations shown on the furniture drawings for these works are generic
representations of the requirements and are not intended to represent the actual
and specific workstation that shall be provided.
D. On the attached furniture floor plans, each piece of furniture or group of pieces of
furniture symbol is tagged with an item number that refers back to the Manual of
Loose Furnishings. It is the responsibility of the Contractor to verify these quantities
and notify the Engineer of any discrepancies and provide all the furniture as per the
Tender/Contract Documents.
E. Accessories : Provide all accessories for each workstation (1) letter trays, (2)
diagonal tray, (3) vertical tray; etc. and associated hardware required for
installation.
H. Finishes:
1. Upholstery-
a) Fabrics as be selected by the Engineer and shown in the Manual of
Loose Furnishings.
2. Metal
a) See manufacturer product specifications for approved metal finish
colors.
b) All exposed metal components shall be consistent color.
c) Hardware metal shall be selected from manufacturers full line by
the Engineer.
3. Work-surfaces
a) Laminate color and finish shall be selected by the Engineer from
the manufacturers full range of selections.
b) Recut Veneer color and finish shall be selected by the
Engineer/Engineers Representative from the manufacturers full
range of selections.
c) All work-surfaces other than wood shall be consistent in
appearance.
4. Wood veneer
a) The Manual of Loose Furnishings for approved wood veneer finish
b) All wood veneer finishes shall be consistent and of Premium
quality.
2.02 MANUFACTURERS
PART 3- EXECUTION
A. Upon the Award of contract, the successful bidder shall field verify and coordinate
all related field conditions and areas. Any questionable field conditions, including,
but not limited to hold dimensions and windows, shall be brought to the attention of
the Engineer.
D. Verify upholstery yardage requirements for each furniture item using fabric
manufacturers width. Coordinate furniture placement such that fabrics of the
same dye lot are used to provide a consistent appearance.
E. Verify electrical power and data locations in field, coordinate with the Contractor.
F. Submit Operation and Maintenance manual to the Owner for approval four (4)
weeks prior to furniture installation. Furnish Owner with three (3) printed and
bound copies of manufacturers recommendations for the care, cleaning and
maintenance of upholstery and finishes. Include detailed written instructions of
methods for cleaning and removal of stains and burns. Provide manufacturers
contact information for each product. At time of installation coordinate with Owner
in order that appropriate personnel conduct an in person orientation session for
Owners housekeeping staff, properly educating them regarding proper care and
maintenance.
3.02 INSTALLATION
A. The installation shall include all items necessary to provide a complete and
functioning work environment.
B. All systems and office furniture shall be plumb and level and installed on top of
flooring without penetration of the finished floor or use of floor fasteners.
D. Contractor at all times shall keep the project site in a neat, clean and safe condition
and free from rubbish caused by performance of the work. At the owners request
and in any event at the completion of work, contractor shall remove all waste
materials and rubbish from and about the project site, as well as all tools,
equipment, machinery and surplus materials
A. Adjust hinges, doors, latches and locks to operate easily without binding. Verify
that workstations are keyed alike and working properly.
C. Protect systems furniture and office furniture from damage, abuse, dust, dirt, stain,
paint or other damage.
END OF SECTION
PART 1- GENERAL
The Contractor shall comply with all regulations, notices and decrees that shall effect the
execution of this Contract and pay all fees in respect thereof.
The Contractor shall give all notices to the Engineer and obtain approval before removing
any fixtures, fittings or services which may belong to others.
The Contractor shall allow for all risks and costs attributable to delay in obtaining labour
and materials other than delays as specifically provided for in the Conditions of Contract.
The Contractor shall allow for the recruitment, hiring and accommodation of all labour
required for the execution of the works and adhere to all local rules and regulations.
Accommodation and labour lines shall be sufficient for the Contractor's own workmen and
sub-contractors.
No important operation shall be carried out without notice in writing being given to the
Engineer sufficiently in advance of the operation to enable him to make such arrangements
as he may deem necessary for its inspection.
Failure to obtain all necessary labour shall not relieve the Contractor of his responsibilities
and obligations under the Contract.
The Engineer will require the use of a checklist system for the proper implementation and
recording on site. Implement a checklist system for the Engineer's approval and abide by
and adhere to these procedures.
Hold regular Project Meetings as necessary for the proper management and coordination
of the Contract and as required by the Engineer.
Attend all meetings and inform Sub-contractors and Suppliers when their presence is
required.
Minutes shall be taken and distributed by the Engineers Representative. Copies will be
furnished to the Contractor.
Pre-Installation Meeting, Progress of the Work Meeting, Coordination of the Work Meeting
and Special Project Meeting each as defined hereunder:
Give the Engineer three weeks notice of the anticipated date of final completion of the
whole or part of the Work.
Each week provide, for verification by the Engineer, a record showing the quantity and type
of furniture, furnishing and equipment delivered to the site on each day of the week.
END OF SECTION
PART 1- GENERAL
1.01 GENERALLY
A. All items shall be new, of first quality, and conform to the drawings and Specifications.
Factory seconds will not be accepted. Installation shall be where shown on the
drawings and as per manufacturers manual/catalogues. All items are to be provided
according to Specifications. Each item must have a sticker identifying the
manufacturers. It must be fixed in an inconspicuous location.
B. All work relating to Furniture and Furnishing is to be fully co-ordinated with all other
construction work including scheduling, dimensional compatibility, co-ordination
with telephone, data and electrical systems, consistent dye lots and finish colours
for the like items which may be procured at various times during the Contract
period.
C. Although such work is not specifically indicated, furnish and install all
supplementary or miscellaneous items, appurtenances and devices incidental to or
necessary for a sound, secure and complete installation.
All items in the Bills of Quantities shall be read as being inclusive of all other
information contained in the Contract Agreement, the Conditions of Contract,
Specifications and the Drawings.
1.02 SUBMITTALS
C. Fabric Samples : Submit three (3) Fabric cuttings 400 x 400mm for all fabrics,
panel fabrics to be used for the Contract.
D. Finish Samples : Submit three (3) samples of all wood, metal and plastic finishes
used on furniture. Samples to be a minimum of 300 x 300 mm. These samples
shall be used as the standard for quality and colour of the finish(es)
1.03 COORDINATION
B. The Contractor is responsible for the consistency of finishes for all wood, metal and
plastic finishes as well as fabrics and leathers regardless of when items are
purchased.
A. It is the Contractor's responsibility to ensure that all items delivered and installed
for the Contract reflect the highest possible quality levels available in the Industry.
Procedures and/or management tools which the Contractor is expected to employ
in undertaking work are as follows :-
D. Testing and Samples : The Contractor shall allow for the supply of samples of all
materials for the approval of the Engineer. Initial samples, once approved, shall
form the standard for reviewing subsequent samples of materials taken at frequent
and regular intervals during the course of the work. Work and materials from which
samples are taken which, in the opinion of the Engineer, fail to match the standard
of the approved samples shall be rejected.
E. The cost of providing such samples together with the cost of mailing or transporting
the samples to and from the Engineer shall be borne by the Contractor.
1.05 MATERIALS
C. Fabrics and leathers shall be free of defects, streaking and discoloration. Fabrics
to be treated to resist stains. All fabrics and upholstery shall be to the approval of
Kuwait Fire Department.
D. All Stainless steel finishes, plated finishes and painted metal finishes shall be free
of any flaws or defects.
1.06 PROCUREMENT
B. Tagging Instructions: Tag or mark each crate, carton and package of furnishings
on the exterior with an identification of the items according to the code and location
as given on specification on sheets.
G. Prior to placing orders, the Contractor shall ensure that hardware, accessories and
fixings are being supplied from the Vendor or third party source. In addition, the
Contractor shall verify that items can fit through doorways and elevators as
necessary.
A. Items are to be stored in air conditioned warehouse facilities which are clean and
with consistent and moderate temperatures and humidity. Items are to be stored or
stacked so that damage is prevented.
B. Items are to be staged (i.e. organised) and containerised according to the staging
plan for installation see installation.
C. A detailed packing list with items identified by item code number, manufacturer and
model number is to be produced during the container packing process. A copy of
the packing list to be placed inside each container as well.
D. Items are to be safely braced and packed into the containers to minimise
movement during transit. Care is to be taken not to stack heavy items on top of
lightweight or fragile items. When necessary cardboard cartons are to be
reinforced with wood frames or skidded to avoid damage and ease of handling.
A. The Contractor is responsible for the preparation of all export and import
documentation in compliance with individual countries and manufacturer's
regulations.
B. Upon arrival of the shipments at the project site or interim local air conditioned
warehouse, the Contractor is to provide an inventory of all items as they are off
loaded from the container. Any discrepancies are to be reported immediately. If
items are not immediately installed the original packing material should be retained
to provide maximum protection.
1.10 INSTALLATION
A. All installation work shall be supervised by the Contractors staff who have
experience in handling and installing systems furniture and Furniture and
Furnishings items.
B. Prepare and submit a detailed staging plan indicating the personnel and Sub-
contractors to be used, proposed schedule, sequencing of materials, and
coordination arrangements.
D. Responsibilities include the uncrating and the complete assembly of all Furniture
and Furnishings items. Each item shall be inspected, cleaned and adjusted as
necessary to assure readiness for operation or use. All items shall be free from
scratches, marks, dust, dirt, tape. labels and adhesive residue.
E. The installation of furniture shall begin only after all construction, electrical,
painting, carpeting and any other finish work has been completed in the space to
be furnished. In addition, the HVAC system is to be fully operational, before the
furniture is installed.
F. All items shall be placed and located as shown on the Drawings. Furniture shall be
set level, drawers and doors with locks and keys shall operate smoothly and not
bend or roll.
G. Installed work shall be free from marrying, scratches, dirt, etc. Damaged items will
be rejected and it will be the Contractor's responsibility to replace within a schedule
agreed with the Engineers Representative.
A. Keep work areas clean and tidy and dispose daily of packaging, wrappings, and
other debris as the work progresses.
F. Identify any other discrepancy that may require the item to be repaired or replaced.
If the inspection shows any item to be unacceptable due to damage or shortage,
the Contractor shall be fully responsible for its replacement or to provide additional
items as specified in the Contract Documents.
G. Prepare a punchlist of items that must be completed and/or corrected prior to final
acceptance.
H. After all discrepancies noted in the preliminary inspection have been corrected,
schedule a final inspection with the Engineers Representative.
A. Be responsible to repair and replace all that could be attributed to faulty material
and workmanship.
A. The Contractor shall supply two copies of updated Project Record Books to record
the following items.
Fabric test reports.
As-installed room list/inventory of all Furniture and Furnishings
Furniture maintenance manual.
B. The Engineers Representative must approve/accept the final inventory and update
Project Record Books prior to final acceptance.
1.14 GUARANTEE
END OF SECTION
MANUFACTURED CASEWORK
PART 1 - GENERAL
1.1 SUMMARY
A. Section Includes:
1. Wood-faced cabinets of stock design.
2. Plastic-laminate-faced wood cabinets of stock design.
3. Plastic-laminate countertops.
4. Solid-surfacing-material countertops.
5. Stainless-steel countertops.
6. Wall shelving.
1.2 DEFINITIONS
B. Exposed Portions of Cabinets: Surfaces visible when doors and drawers are closed,
including bottoms of cabinets more than 1220 mm above floor, and surfaces visible in
open cabinets.
D. Concealed Portions of Cabinets: Surfaces not usually visible after installation, including
sleepers, web frames, dust panels, and ends and backs that are placed directly against
walls or other cabinets.
1.3 SUBMITTALS
B. Shop Drawings: Include plans, elevations, sections, details, and attachments to other
work. Show fabrication details, including types and locations of hardware. Show
installation details, including field joints and filler panels. Indicate manufacturer's
catalog numbers for casework.
C. Samples for Initial Selection: For cabinet finishes and for each type of top material
indicated.
D. Samples for Verification: 200-by-250-mm Samples for each type of finish, including top
material.
B. Source Limitations: Obtain manufactured wood casework from single source from
single manufacturer.
C. Quality Standard: Unless otherwise indicated, comply with requirements for modular
cabinets in AWI's "Architectural Woodwork Quality Standards."
A. Deliver manufactured wood casework only after painting, utility roughing-in, and similar
operations that could damage, soil, or deteriorate casework have been completed in
installation areas. If casework must be stored in other than installation areas, store only
in areas where environmental conditions meet requirements specified in "Project
Conditions" Article.
B. Keep finished surfaces covered with polyethylene film or other protective covering
during handling and installation.
1.7 COORDINATION
A. Coordinate layout and installation of framing and reinforcements in walls and partitions
for support of manufactured wood casework.
2. Warranty Period: Five years from the end of the maintenance period mentioned
above.
A. Furnish complete touchup kit for each type and finish of manufactured wood casework
provided. Include scratch fillers, stains, finishes, and other materials necessary to
perform permanent repairs to damaged casework finish.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
1. Manufactured Casework:
a. Architectural Cabinet Systems; a division of Windham Millwork, Inc.
b. CampbellRhea; a Sagas International company.
c. CIF Furniture Ltd.
d. Fisher Hamilton L.L.C.
e. Kewaunee Scientific Corporation.
f. Mid Canada Millwork Ltd.
g. R. C. Smith Company.
h. Terrill Manufacturing Company.
i. TMI Systems Design Corporation.
B. Maximum Moisture Content for Lumber: 7 percent for hardwood and 12 percent for
softwood.
C. Hardwood Plywood: HPVA HP-1, either veneer core or particleboard core unless
otherwise indicated.
a. Abet Inc.
b. Arborite; a division of ITW Canada.
c. Formica Corporation.
d. Lamin-Art, Inc.
e. Nevamar Company, LLC; Decorative Products Div.
f. Panolam Industries International Incorporated.
g. Wilsonart International; Div. of Premark International, Inc.
1. Select wood edgebanding for grain and color compatible with face veneers.
N. Cold-Rolled Steel Sheet: ASTM A 1008/A 1008M, suitable for exposed applications.
O. Stainless-Steel Sheet: ASTM A 240 or ASTM A 666, Type 304, with No. 4 satin finish.
a. ABA Industries.
b. Avonite Surfaces; Aristech Acrylics LLC.
c. E. I. du Pont de Nemours and Company.
d. Formica Corporation.
e. LG Solid Source, L.L.C.
f. Meganite Inc.; a division of The Pyrochem Group.
g. Nevamar Company, LLC; Decorative Products Div.
h. Samsung; Cheil Industries Inc.
i. Swan Corporation (The).
j. Transolid, Inc.
k. Wilsonart International; Div. of Premark International, Inc.
A. Preparation: Sand lumber and plywood for manufactured wood casework construction
before assembling. Sand edges of doors and drawer fronts and molded shapes with
profile-edge sander. Sand casework after assembling for uniform smoothness at least
equivalent to that produced by 220-grit sanding and without machine marks, cross
sanding, or other surface blemishes.
B. Staining: Remove fibers and dust and apply wash-coat sealer and stain to exposed
and semiexposed surfaces as required to provide uniform color and to match approved
samples.
1. Use threaded metal or plastic inserts with machine screws for fastening to
particleboard except where hardware is through-bolted from back side.
C. Pulls: Solid stainless-steel wire pulls, fastened from back with two screws. For sliding
doors, provide recessed stainless-steel flush pulls. Provide 2 pulls for drawers more
than 600 mm wide.
2.7 COUNTERTOPS
A. Countertops, General: Provide smooth, clean exposed tops and edges in uniform
plane free of defects. Provide front and end overhang of 25 mm over base cabinets.
1. Weld shop-made joints, and grind and polish surfaces to produce uniform,
directional, textured, polished finish indicated, free of cross scratches. When
polishing is completed, passivate and rinse surfaces. Remove embedded foreign
matter and leave surfaces chemically clean.
2. Sound deaden undersurface with heavy-build mastic coating.
B. Adjustable Shelf Supports: Zinc-plated steel standards and shelf brackets, complying
with BHMA A156.9, Types B04102 and B04112, surface mounted.
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine areas, with Installer present, for compliance with requirements for installation
tolerances, location of framing and reinforcements, and other conditions affecting
performance of manufactured wood casework.
B. Proceed with installation only after unsatisfactory conditions have been corrected.
A. Install level, plumb, and true; shim as required, using concealed shims. Where
manufactured wood casework abuts other finished work, apply filler strips and scribe for
accurate fit, with fasteners concealed where practical.
B. Base Cabinets: Set cabinets straight, level, and plumb. Adjust subtops within 1.5 mm
of a single plane. Fasten cabinets to masonry or framing, wood blocking, or
reinforcements in walls and partitions with fasteners spaced 600 mm o.c. Bolt adjacent
cabinets together with joints flush, tight, and uniform. Align similar adjoining doors and
drawers to a tolerance of 1.5 mm.
C. Wall Cabinets: Hang cabinets straight, level, and plumb. Adjust fronts and bottoms
within 1.5 mm of a single plane. Fasten to hanging strips, masonry, or framing,
blocking, or reinforcements in walls or partitions. Align similar adjoining doors to a
tolerance of 1.5 mm.
D. Install hardware uniformly and precisely. Set hinges snug and flat in mortises unless
otherwise indicated. Adjust and align hardware so moving parts operate freely and
contact points meet accurately. Allow for final adjustment after installation.
E. Adjust casework and hardware so doors and drawers operate smoothly without warp or
bind. Lubricate operating hardware as recommended by manufacturer.
A. Field Jointing: Where possible make in the same manner as shop jointing, using
dowels, splines, adhesives, and fasteners recommended by manufacturer. Prepare
edges to be joined in shop so Project-site processing of top and edge surfaces is not
required. Locate field joints where shown on Shop Drawings.
B. Secure tops to cabinets with Z- or L-type fasteners or equivalent, using two or more
fasteners at each front, end, and back.
C. Abut top and edge surfaces in one true plane, with internal supports placed to prevent
deflection.
1. Fasten shelf standards at ends and not more than 300 mm o.c.
B. Install shelf standards plumb and at heights to align shelf brackets for level shelves.
Space standards not more than 750 mm o.c.
C. Install shelving level and straight, closely fitted to other work where indicated.
END OF SECTION
ENTRANCE MATS
PART 1 - GENERAL
1.1 SUMMARY
1.2 SUBMITTALS
E. Maintenance Data: For floor mats and frames to include in maintenance manuals.
A. Source Limitations: Obtain floor mats and frames through one source from a single
manufacturer.
1.5 COORDINATION
A. Coordinate size and location of recesses in concrete with installation of finish floors to
receive floor mats and frames.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
2.2 MATERIALS
D. Grid Frame: DP Drain Pan Series, as manufactured by C/S Group, or approved equal;
106.4mm deep with 12.7mm exposed surface in aluminum alloy. Assembly shall rest on
a continuous vinyl cushion with additional support members at 810mm c/c. Provide
adjustable aluminum support leg at 610mm along each support member, staggered side
to side. Manufacturer shall provide a 16 gauge aluminum pan complete with a 50.8mm
IPS drain and stainless steel strainer. Frame color shall be as selected and approved by
Engineer/Engineers Representative from manufacturer's full range of colors.
E. Tread Insert: Exterior carpet; solution dyed polypropylene fibers with 50/50 blend of
600/12-denier multi-filament and 595/D1 monofilament in color as selected and approved
by Engineer/Engineers Representative from manufacturer's standard choices. Textured
fibers shall have ultraviolet blockers and color as integral part of the filament. Carpet
fiber and monofilament shall be fusion-bonded to a rigid two-ply backing to prevent
fraying and supplied in continuous splice-free lengths. Waterproof fibers shall not get
soggy, rot, fade or stain.
A. Provide concrete grout and fill equivalent in strength to cast-in-place concrete slabs for
recessed mats and frames. Use aggregate no larger than one-third fill thickness.
2.4 FABRICATION
A. Floor Mats: Shop fabricate units to greatest extent possible in sizes indicated. Unless
otherwise indicated, provide single unit for each mat installation; do not exceed
manufacturer's recommended maximum sizes for units that are removed for maintenance
and cleaning. Where joints in mats are necessary, space symmetrically and away from
normal traffic lanes. Miter corner joints in framing elements with hairline joints or provide
prefabricated corner units without joints.
C. Coat surfaces of aluminum frames that will contact cementitious material with
manufacturer's standard protective coating.
A. General: Comply with NAAMM's "Metal Finishes Manual for Architectural and Metal
Products" for recommendations for applying and designating finishes.
B. Finish designations prefixed by AA comply with the system established by the Aluminum
Association for designating aluminum finishes.
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine substrates and floor conditions for compliance with requirements for location,
sizes, minimum recess depth, and other conditions affecting installation of floor mats
and frames.
1. Proceed with installation only after unsatisfactory conditions have been corrected.
3.2 INSTALLATION
A. Install recessed mat frames to comply with manufacturer's written instructions. Set mat
tops at height recommended by manufacturer for most effective cleaning action;
coordinate top of mat surfaces with bottom of doors that swing across mats to provide
clearance between door and mat.
3.3 PROTECTION
A. After completing frame installation and concrete work, provide temporary filler of plywood
or fiberboard in recesses and cover frames with plywood protective flooring. Maintain
protection until construction traffic has ended and Project is near Substantial Completion.
END OF SECTION
PART 1 - GENERAL
1. Shade system shall not be installed until the building is operating at ambient
temperature and humidity ranges consistent with that intended for buildings
ultimate use.
1.9 MAINTENANCE
A. Make ordering of new equipment for expansions, replacements, and spare parts
available to a qualified dealer or installer.
B. Make replacement parts available for minimum of ten years from date of manufacture.
C. Provide factory direct technical support hotline 24 hours per day, 7 days per week.
D. Provide on-site service support within 24 hours anywhere in continental United
States and within 72 hours worldwide except where special visas are required.
E. Offer renewable service contract on yearly basis, to include parts, factory labor, and
annual training visits. Make service contracts available up to ten years after date of
system commissioning.
PART 2- PRODUCTS
2.1 MANUFACTURERS
A. Basis of design product: Lutron Sivoia QED (www.lutron.com) or subject to compliance
and prior approval with specified requirements of this section, one of the following:
1. MechoShade Systems, Inc (www.mechoshade.com)
2.2 APPLICATION/SCOPE
A. Roller shade schedule
1. Shade Type 1: Motorized interior solar roller shade utilizing quiet, low voltage,
precision controlled Electronic Drive Unit.
2. Shade Type 2: Motorized interior room darkening roller shade with blackout
fabric utilizing quiet, low voltage, precision controlled Electronic Drive Unit.
END OF SECTION
PART 1 - GENERAL
A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 1 Specification Sections, apply to this Section.
1.2 SUMMARY
1.3 SUBMITTALS
A. Product Data: For each type of product indicated. Include construction details, material
descriptions, dimensions of individual components and profiles, and finishes for fixed
audience seating.
B. Shop Drawings: Include plans, elevations, sections, details, and attachments to other
work.
1. Seating Layout: Show seating layout, aisle widths, row-lettering and chair-
numbering scheme, chair widths, and chair spacing in each row.
2. Accessories: Show accessories, including locations of left- and right-hand tablet
arms, electrical devices, accessibility provisions, and attachments to other work.
C. Samples for Initial Selection: For each type of exposed finish, color, texture, and pattern
indicated.
D. Samples for Verification: For each type of exposed finish required, prepared on Samples
of size indicated below:
1. Wood and Plywood Materials and Finishes: Manufacturer's standard-size unit, not
less than 75 mm square.
2. Upholstery Fabric: Full width by 914-mm long section of fabric from dye lot to be
used for the Work, with specified treatments applied. Show complete pattern
repeat. Mark top and face of fabric.
A. Source Limitations: Obtain each type of seating required, including accessories and
mounting components, from single source from single manufacturer.
1. Upholstery Fabric: Obtain fabric of a single dye lot for each color and pattern of
fabric required.
1. Fabric: Class 1 according to DOC CS 191 and 16 CFR 1610.61, tested according
to California Technical Bulletin 117.
2. Padding: Comply with California Technical Bulletin 117.
3. Full-Scale Fire Test: Comply with California Technical Bulletin 133.
A. Environmental Limitations: Do not deliver or install seating until spaces are enclosed and
weathertight, wet work in spaces is complete and dry, work above ceilings is complete,
and temporary or permanent HVAC system is operating and maintaining ambient
temperature and humidity conditions at occupancy levels during the remainder of the
construction period.
1.6 WARRANTY
A. Special Warranty: Contractor agrees to repair or replace components of fixed audience seating
that fail in materials or workmanship within specified maintenance period of two years.
A. Furnish extra materials from the same production run that match products installed and
that are packaged with protective covering for storage and identified with labels
describing contents.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
A. Fixed Theater Seating: basis-of design product: Subject to compliance with the
requirements, provide products manufactured by Poltrona Frau; (www.poltronafrau.it), or
comparable product by one of the following:
1. Figueras (www.figueras-usa.com).
2. Skeie: www.skeie.no.
2.2 MATERIALS
A. Cast Iron: ASTM A 48/A 48M, Class 25A minimum, free of air holes and casting
imperfections, all edges ground smooth.
B. Sheet Steel: ASTM A 591/A 591M, Commercial Steel (CS) or Drawing Steel (DS)
electrogalvanized sheet, 40Z (12G) coating class; chemically treated for baked ename
finish.
C. Exposed Hardwood: Solid lumber selected for absence of visible defects; birch, northern
hard maple, white oak, or species standard with manufacturer.
D. Exposed Hardwood: Solid lumber selected for absence of visible defects; same species
as specified for "Hardwood Plywood".
E. Hardwood Plywood: Type "WD-3" as specified under Section 06050 - Basic Wood
Veneer Materials
F. Polyurethane Foam: Density not less than 28.8 kg/cu m, fire retardant, nonhardening and
non-oxidizing, with high resistance to alkalis, oils, moisture, and mildew.
A. Fixed seating system designed to permit radial installation using common middle support
standards in each row and aisle standards aligned as indicated on drawings. Width of
seats not less than 559 mm, except exit seat locations may be reduced to 508 mm to
complete specific row dimensions.
B. Backs: Fixed type; two-panel construction with fabric covering over padding and
protective back panel, with installed height not less than 813 mm above finished floor.
1. Padding: Polyurethane foam not less than 25 mm thick bonded to structural
support.
2. Covering: Fabric bonded to padding and fastened by upholstery technique that
facilitates replacement.
3. Rear Panel: One-piece molded plywood, not less than 6.4 mm thick, with exposed
back surface of hardwood face veneer.
C. Seats: Hinged type, constructed to permit reupholstering without removing seat from
chair.
D. Hinges: Self-lubricating, noiseless steel hinges with brass alloy bearings or nylon
bushings, equipped with spring mechanism that causes unoccupied seat to rise
automatically to uniform 3/4 fold, with 100 percent fold when additional pressure is
applied.
E. Arm Rests: Locate at aisles and between chairs; mount to support standard with
concealed fasteners; exposed surfaces of solid hardwood lumber with smoothed edges.
F. End Panels: One piece panels fastened securely to aisle standards with concealed
fasteners, configured as follows:
1. Shape: Rectangular.
2. Finish: Solid hardwood.
2.4 STANDARDS
A. Support Standards: One-piece cast iron, with integral mounting points for backs, seats,
and arm rests, and integral floor anchoring points.
2.5 ACCESSORIES
A. Folding Tablet Arms: At standard to right side of each seat, provide manufacturer's
standard fold-away tablet arm assembly, with hinge and swivel mechanism securely
fastened to underside of writing surface and designed to provide solid support in the
open position and semi-automatic return to stowed position beneath right arm rest and
parallel to right standard.
1. Finish: Hardwood plywood veneer, with smooth, rounded edges.
2. Size: Writing surface not less than 0.0645 sq. m (100 sq inches).
2.6 FINISHES
A. Ferrous Metals: Manufacturer's standard two-coat baked enamel finish, applied over
conversion coating appropriate to base metal.
3.1 EXAMINATION
A. Examine floors, risers, and other adjacent work and conditions, with Installer present, for
compliance with requirements and other conditions affecting performance of the Work.
C. Proceed with installation only after unsatisfactory conditions have been corrected.
3.2 INSTALLATION
1. Use installation methods and fasteners that produce fixed audience seating
assemblies with individual chairs capable of supporting an evenly distributed 272-
kg static load without failure or other conditions that might impair the chair's
usefulness.
2. Install standards and pedestals plumb.
B. Install seating with chair end standards aligned from first to last row and with backs and
seats varied in width and spacing to optimize sightlines.
3.3 ADJUSTING
A. Adjust chair backs so that they are aligned with each other in rows.
B. Adjust self-rising seat mechanisms so seats in each row are aligned when in upright
position.
E. Repair minor abrasions and imperfections in finishes with coating that matches factory-
applied finish.
END OF SECTION
Pages
6.0 Specification
i) Section : 12000 Furniture. 12000 - 1 to 6
Typical A
DKSY90
Plan - 1:50
DKSY90
SCTS50
Typical A1
DKSY91
Plan - 1:50
DKSY91
SCTS50
Typical A2
DKSY92
Plan - 1:50
DKSY92
SCTS50
Typical A3
DKSY93
Plan - 1:50
DKSY93
SCTS50
SCSI50
Typical A4
DKSY94
Plan - 1:50
Note: Files will vary depending on
architecture. Always provide wardrobe
cabinet.Field verify for quantity.
DKSY94
SCTS50
Typical B
DKSY80
Plan - 1:50
DKSY80
SCTS50
Typical B1
DKSY81
Plan - 1:50
DKSY81
SCTS50
Typical C
DKSY70
Plan - 1:50
DKSY70
SCTS50
Typical D
DKSY61
Plan - 1:50
DKSY61
SCTS50
Typical E
DKSY60
Plan - 1:50
DKSY60
SCTS50
Typical F
DKSY50 and DKSY51
Plan - 1:50
Plan - 1:50
PO-20
Plan - 1:50
SCTS20
DKSY20
TBLT20 SS3S20
SCSI20 TBLC20
TBLE20
PO-21
Plan - 1:50
DKCR20
TBCF20 SS3S20
SCCF20 TBLE20
SS3S20
TBLC20
PO-22
Plan - 1:50
DKSY85
SS3S20 SCTS50
TBLE20 TBLC20
TBLC20 SCLN20
SCLN20
PO-30
Plan - 1:100
TBLE30 SS3S30
SCLN30 TBLC30
TBLE30 SCSI30
SCLN30 TBCF30
TBCN30 TBLT30
SCSI30
SCTS30
DKSY30
PO-40
Plan - 1:100
TBLE40
SCLN40
SS3S40
TBLC40
TBLT30
SCSI40
SCTS30
DKSY40
PO-50
Plan - 1:50
DKSY52
SCTS50
SS3S40
SCSI40
TBLT30
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.2
FURNITURE CATALOG CUTS
ACWB20
Recommended Product Item: White Board System
Manufacturer: Nienkamper
Model No.: See notes below
Description: Vox Rail and white board system
Finish: Polished aluminum
Size.: w144 h42
Upholstery Mfg.: Egan
Upholstery #: To be selected
Alternate Manufacturer #1
Manufacturer: Borks
Model No.: See notes below
Description: Rail and white board system
Finish: Polished aluminum
Size.: w138 h51.3
Upholstery Mfg.: Borks
Upholstery #: To be selected
Alternate Manufacturer #2
Manufacturer: Teknion
Model No.: See notes below
Description: Focus wall rail and white board system
Finish: Polished aluminum
Size.: w144 h42
Upholstery Mfg.: Teknion
Upholstery #: To be selected
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.3
FURNITURE CATALOG CUTS
ACWB50
Recommended Product Item: White Board System
Manufacturer: Nienkamper
Model No.: See notes below
Description: Vox Rail and white board system
Finish: Polished aluminum
Size.: w120 h42
Upholstery Mfg.: Egan
Upholstery #: To be selected
Alternate Manufacturer #1
Manufacturer: Borks
Model No.: See notes below
Description: Rail and white board system
Finish: Polished aluminum
Size.: w120 h51.3
Upholstery Mfg.: Borks
Upholstery #: To be selected
Alternate Manufacturer #2
Manufacturer: Teknion
Model No.: See notes below
Description: Focus wall rail and white board system
Finish: Polished aluminum
Size.: w120 h42
Upholstery Mfg.: Teknion
Upholstery #: To be selected
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.4
FURNITURE CATALOG CUTS
BCS350
Recommended Product Item: Bookcase, 3 Shelves
Manufacturer: Knoll
Model No.: C2B3936
Description: Calibre 39 High Bookcase, 2 adjustable shelves
Finish: Silver (to match typical workstations)
Size.: w36 d15 h39
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: 46-3615-OB-42-SS-T1-NS2-B2
Description: Meridian 39 High Bookcase, 2 adjustable shelves
Finish: MS Metallic Silver (to match typical workstations)
Size.: w36 d15 h42
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: JBCS0336
Description: X series three-high bookcase
Finish: Metallic silver
Size.: w36 d14 h39 1/2
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.5
FURNITURE CATALOG CUTS
BCS450
Recommended Product Item: Bookcase, 4 Shelves
Manufacturer: Knoll
Model No.: C2B5136
Description: Calibre 51 High Bookcase, 2 adjustable shelves
Finish: Silver (to match typical workstations)
Size.: w36 d15 h51
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: 46-3615-OB-55-SS-T1-NS2-B2
Description: Meridian 55 High Bookcase, 2 adjustable shelves
Finish: MS Metallic Silver (to match typical workstations)
Size.: w36 d15 h55
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: JBCS0436
Description: X series four-high bookcase
Finish: Metallic silver
Size.: w36 d14 h51 1/2
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.6
FURNITURE CATALOG CUTS
BCS550
Recommended Product Item: Bookcase, 5 Shelves
Manufacturer: Knoll
Model No.: C2B6336
Description: Calibre 63 High Bookcase, 4 adjustable shelves
Finish: Silver (to match typical workstations)
Size.: w36 d15 h63
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: 46-3615-OB-68-SS-T1-NS4-B2
Description: Meridian 65 High Bookcase, 4 adjustable shelves
Finish: MS Metallic Silver (to match typical workstations)
Size.: w36 d15 h68
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: JBCS0536
Description: X series five-high bookcase
Finish: Metallic silver
Size.: w36 d14 h63 1/2
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.7
FURNITURE CATALOG CUTS
CACC60
Recommended Product Item: Cabinet, Card Catalog
Manufacturer: Spacesaver
Model No.:
Description: Card catlog file system
Finish: To be determined
Size.: To be determined
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: BCI
Model No.:
Description: Card catlog file system
Finish: To be determined
Size.: To be determined
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #2
Manufacturer: Demco
Model No.:
Description: Card catlog file system
Finish: To be determined
Size.: To be determined
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.8
FURNITURE CATALOG CUTS
CAML50
Recommended Product Item: Cabinet, Mail Cubbies
Manufacturer: Mayline Group
Model No.: SC4848GL
Description: Elevated closed-back sorter
Finish: To be selected
Size.: w48 d15 h48
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: International Office Products Cooperatibve
Model No.: MDR - 42048
Description: Desktop organizer/sorter on riser
Finish: To be selected
Size.: w47.25 d15.75 h41.75
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #2
Manufacturer: Hamilton Sorter
Model No.: L4-30E18
Description: Legal size sort module
Finish: To be selected
Size.: w48 d30 h48
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.9
FURNITURE CATALOG CUTS
CASR60
Recommended Product Item: Storage Cabinet, Lockable
Manufacturer:
Model No.:
Description:
Finish:
Size.:
Upholstery Mfg.:
Upholstery #:
Notes:
Alternate Manufacturer #1
Manufacturer:
Model No.:
Description:
Finish:
Size.:
Upholstery Mfg.:
Upholstery #:
Notes:
Alternate Manufacturer #2
Manufacturer:
Model No.:
Description:
Finish:
Size.:
Upholstery Mfg.:
Upholstery #:
Notes:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.10
FURNITURE CATALOG CUTS
CTBK60
Recommended Product Item: Cart, Books
Manufacturer: Bretford
Model No.: BOOV1
Description: Contemporary double-sided 3 shelf book truck
Finish: AL Aluminum
Size.: w37 d18 h43
Upholstery Mfg.: n/a
Upholstery #: n/a
Notes:
Alternate Manufacturer #1
Manufacturer: Gresswell
Model No.: Luxor 3495
Description: Double-sided 3 shelf book trolley
Finish:
Size.:
Upholstery Mfg.:
Upholstery #:
Notes:
Alternate Manufacturer #2
Manufacturer:
Model No.:
Description:
Finish:
Size.:
Upholstery Mfg.:
Upholstery #:
Notes:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.11
FURNITURE CATALOG CUTS
DKCR20
Recommended Product Item: Credenza
Manufacturer: Halcon
Model No.: See Notes below
Description: Stria 78 Low Credenza
Finish: Walnut, Quater Cut w/ clear stain, Spacer-Sycamore
Size.: w78 d25 h30
Upholstery Mfg.: n/a
Upholstery #: n/a
78 Credenza worksurface
30 Credenza worksurface pedestal
18 Credenza worksurface pedestal
30 Credenza worksurface pedestal
Coordinate with audio/visual contractor for location of
audio/visual equipment.
Coordinate wtih electrical contractor.
Alternate Manufacturer #2
Manufacturer: Gianni
Model No.: Custom
Description: 78 Low Credenza
Finish: Walnut, Quater Cut w/ clear stain, Spacer-Sycamore
Size.: w78 d25 h30
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.12
FURNITURE CATALOG CUTS
DKCR20
Credenza
Sycamore spacer
Walnut cabinet, base and top
1 adjustable shelf
Elevation @ Credenza
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.13
FURNITURE CATALOG CUTS
DKCR25
Recommended Product Item: Credenza
Manufacturer: Halcon
Model No.: Custom - See notes below
Description: Stria Credenza
Finish: Walnut, Quater Cut w/ clear stain, Spacer-Sycamore
Size.: w174 d 25 h88
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Nucraft
Model No.: See notes below
Description: Credenza
Finish: Natural Walnut
Size.: w174 d 25 h88
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #2
Manufacturer: Gianni
Model No.: See notes below
Description: Credenza
Finish: Walnut, Quater Cut w/ clear stain
Size.: w174 d 25 h88
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.14
FURNITURE CATALOG CUTS
DKCR25
Credenza
Wardrobe cabinet
Vertical cabinet w/
adjustable shelves
Elevation @ Credenza
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.15
FURNITURE CATALOG CUTS
DKCR35
Recommended Product Item: Credenza
Manufacturer: Nienkamper
Model No.: 23434
Description: Vox credenza on glides
Finish: F19 Natural Walnut, Quater cut book match
Size.: w94 3/8d 25 3/8 h 34 1/4
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Walter Knoll
Model No.: Custom
Description: Credenza
Finish: Natural walnut, silver anodized aluminum
Size.: w96 d24 h30
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #2
Manufacturer: Teknion
Model No.: AFCVAS9029WDB7NN2
Description: Audience veneer credenza with doors
Finish: WP medium walnut, anodized aluminum
Size.: w90d20 h 29
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.16
FURNITURE CATALOG CUTS
DKCR36
Recommended Product Item: Credenza
Manufacturer: Nienkamper
Model No.: 23434 - Custom depth
Description: Vox credenza on glides
Finish: F19 Natural Walnut, Quater cut book match
Size.: w94 3/8 d18 h 34 1/4
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Walter Knoll
Model No.: Custom
Description: Credenza
Finish: Natural walnut, silver anodized aluminum
Size.: w96 d18 h30
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #2
Manufacturer: Teknion
Model No.: AFCVAS9029WDB7NN2
Description: Audience veneer credenza with doors
Finish: WP medium walnut, anodized aluminum
Size.: w90d20 h 29
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.17
FURNITURE CATALOG CUTS
DKCR37
Recommended Product Item: Credenza
Manufacturer: Nienkamper
Model No.: 23433
Description: Vox credenza on glides
Finish: F19 Natural Walnut, Quater cut book match
Size.: w70 3/4d 25 3/8 h 34 1/4
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Walter Knoll
Model No.: Custom
Description: Credenza
Finish: Natural walnut, silver anodized aluminum
Size.: w72 d24 h30
Upholstery Mfg.: n/a
Upholstery #: n/a
Notes:
Alternate Manufacturer #2
Manufacturer: Teknion
Model No.: AFCVAS7229WDB7NN2
Description: Audience veneer credenza with doors
Finish: WP medium walnut, anodized aluminum
Size.: w72d20 h 29
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.18
FURNITURE CATALOG CUTS
DKCR50
Recommended Product Item: Credenza
Manufacturer:
Model No.:
Description:
Finish:
Size.:
Upholstery Mfg.:
Upholstery #:
Notes:
Alternate Manufacturer #1
Manufacturer:
Model No.:
Description:
Finish:
Size.:
Upholstery Mfg.:
Upholstery #:
Notes:
Alternate Manufacturer #2
Manufacturer:
Model No.:
Description:
Finish:
Size.:
Upholstery Mfg.:
Upholstery #:
Notes:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.19
FURNITURE CATALOG CUTS
DKSY01
Recommended Product Item: Desk, Double Pedestal Minister
Manufacturer: Halcon
Model No.: See Notes Below
Description: Mitre Double Pedestal Desk
Finish: Walnut, Quater cut w/clear stain
Size.: w90 d36 h31
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Gianni
Model No.: See Notes Below
Description: Double Pedestal Desk
Finish: Walnut, Quater cut w/clear stain
Size.: w90 d36 h31
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #2
Manufacturer: CCN International
Model No.: QD000S-3690-CD modified modesty panel
Description: Foundation double pedestal desk - custom
Finish: Walnut, Quater cut w/clear stain
Size.: w90 d36 h31
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.20
FURNITURE CATALOG CUTS
DKSY05
Recommended Product Item: Desk, Writing
Manufacturer: A. Rudin
Model No.: Custom
Description: Writing desk
Finish: 60 Tobacco
Size.: w48 d24 h30
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Niedermaier
Model No.: F1-11579-S
Description: Writing desk
Finish: Custom - natural walnut on maple
Size.: w48 d24 h30.25
Upholstery Mfg.: n/a
Upholstery #: n/a
Notes:
Alternate Manufacturer #2
Manufacturer: Todd Hase
Model No.: Custom
Description: Gene writing desk
Finish:
Size.: w48 d24 h30
Upholstery Mfg.: n/a
Upholstery #: n/a
Notes:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.21
FURNITURE CATALOG CUTS
DKSY10
Recommended Product Item: Desk, Double Pedestal Under Secretary
Manufacturer: Halcon
Model No.: See Notes Below
Description: Mitre Double Pedestal Desk
Finish: Walnut, Quater cut w/clear stain
Size.: w84 d36 h31
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Gianni
Model No.: Custom, see notes below
Description: Double Pedestal Desk
Finish: Walnut, Quater cut w/clear stain
Size.: w84 d36 h31
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #2
Manufacturer: CCN International
Model No.: QD000S-3684-CD modified modesty panel
Description: Foundation double pedestal desk - custom
Finish: w84 d36 h31
Size.: w84 d36 h31
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.22
FURNITURE CATALOG CUTS
DKSY20
Recommended Product Item: Desk, Double Pedestal Asst. Under Secretary
Manufacturer: Halcon
Model No.: See Notes Below
Description: Stria Desk & Credenza
Finish: Walnut, Quater Cut w/ clear stain - all sides finished
Size.: w78 d36 h29; w144 d24 h70
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Bernhardt
Model No.: See notes below
Description: Shift Desk & Credenza
Finish: Walnut, Quater Cut w/ clear stain - all sides finished
Size.: w78 d36 h29
Upholstery Mfg.: n/a
Upholstery #: n/a
DKSY20
Desk, Double Pedestal Asst. Under Secretary
F/F Pedestal
Elevation @ Credenza
Scale: 1:50
DKSY30
Recommended Product Item: Desk, System L2 Department Manager
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada AS-3 wood desk system
Finish: V2 Burnt Walnut, 613 Silver
Size.: See drawng
Upholstery Mfg.: n/a
Upholstery #: n/a
DKSY30
Desk, System L2 Department Manager
Pencil drawer
Box/box/file
pedestal w/lock, wood
Wardrobe w/sliding
door/open bookcase, wood
shelves
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.26
FURNITURE CATALOG CUTS
DKSY40
Recommended Product Item: Desk, System L3 Supervisor
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada AS-3 wood desk system
Finish: V2 Burnt Walnut, 613 Silver
Size.: See drawng
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Geiger
Model No.: See drawing
Description: Tablet wood desk system
Finish: 676 Cocoa Walnut, Satin Chrome
Size.: See drawing
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: See drawing
Description: Masters series wood desk system
Finish: Retro on Walnut
Size.: See drawing
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.27
FURNITURE CATALOG CUTS
DKSY40
Desk, System L3 Supervisor
Pencil drawer
Box/box/file
pedestal w/lock, wood
Wardrobe w/sliding
door/open bookcase, wood
shelves
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.28
FURNITURE CATALOG CUTS
DKSY50
Recommended Product Item: Desk, System F Head of Section
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada desk system
Finish: V2 Burnt Walnut, 613 Silver, White
Size.: See drawng
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: See drawing
Description: Vivo desk system
Finish: 676 Cocoa Walnut, Satin Chrome, 91 White
Size.: See drawing
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: See drawing
Description: Compose desk system
Finish: Retro on Walnut, Silver, White
Size.: See drawing
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.29
FURNITURE CATALOG CUTS
DKSY50
Desk, System F Head of Section/Consultant
Box/box/file
pedestal w/lock,
wood front
Wood worksurface
Pencil drawer
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.30
FURNITURE CATALOG CUTS
DKSY51
Recommended Product Item: Desk, System F panels
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada AS-2 desk system
Finish: White, Silver
Size.: See drawng
Upholstery Mfg.: Knoll
Upholstery #: To be determined
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: See drawing
Description: Vivo desk system
Finish: 91 White, Silver
Size.: See drawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: See drawing
Description: Compose desk system
Finish: White, Silver
Size.: See drawing
Upholstery Mfg.: Haworth
Upholstery #: To be determined
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.31
FURNITURE CATALOG CUTS
DKSY51
Desk, System F panels
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.32
FURNITURE CATALOG CUTS
DKSY52
Recommended Product Item: Desk, System F1 Psychologist
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada AS-2 desk system
Finish: V2 Burnt Walnut, 613 Silver, White
Size.: See drawng
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: See drawing
Description: Vivo desk system
Finish: 676 Cocoa Walnut, Satin Chrome, 91 White
Size.: See drawing
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: See drawing
Description: Compose desk system
Finish: Retro on Walnut, Silver, White
Size.: See drawing
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.33
FURNITURE CATALOG CUTS
DKSY52
Desk, System F1 Psychologist
Box/box/file
pedestal w/lock,
wood front
Wood worksurface
Pencil drawer
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.34
FURNITURE CATALOG CUTS
DKSY60
Recommended Product Item: Desk, System E
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada desk system
Finish: Maple techwood, silver
Size.: See draawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
DKSY60
Desk, System E
h49 panel,
spline only h21 frosted glass screen
d18 wood worksurface
Box/box/file pedestal
Pencil drawer
File/file pedestal
h49 bookcases
h49 wardrobe cabinet
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.36
FURNITURE CATALOG CUTS
DKSY61
Recommended Product Item: Desk, System D
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada desk system
Finish: Maple techwood, silver
Size.: See draawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: See drawing
Description: Vivo desk system
Finish: Natural Maple recut veneer, metallic silver
Size.: See drawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: See drawing
Description: Compose desk system
Finish: Beachwood doublecut veneer, metallic silver
Size.:
Upholstery Mfg.:
Upholstery #:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.37
FURNITURE CATALOG CUTS
DKSY61
Desk, System D
Open shelves
h39 wardrobe
cabinet
h39 bookcases
(2 adj. shelves)
see BCS350
Common top,
see furniture
drawings
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.38
FURNITURE CATALOG CUTS
DKSY70
Recommended Product Item: Desk, System C
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada desk system
Finish: Maple techwood, silver
Size.: See draawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: See drawing
Description: Vivo desk system
Finish: Natural Maple recut veneer, metallic silver
Size.: See drawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: See drawing
Description: Compose desk system
Finish: Beachwood doublecut veneer, metallic silver
Size.:
Upholstery Mfg.:
Upholstery #:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.39
FURNITURE CATALOG CUTS
DKSY70
Desk, System C
h64 wardrobe/storage
cabinet
Pencil drawer
Box/box/file pedestal
h64 panel,
all sides
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.40
FURNITURE CATALOG CUTS
DKSY80
Recommended Product Item: Desk, System B
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada desk system
Finish: Maple techwood, silver
Size.: See draawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: See drawing
Description: Vivo desk system
Finish: Natural Maple recut veneer, metallic silver
Size.: See drawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: See drawing
Description: Compose desk system
Finish: Beachwood doublecut veneer, metallic silver
Size.:
Upholstery Mfg.:
Upholstery #:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.41
FURNITURE CATALOG CUTS
DKSY80
Desk, System B
File/file pedestal
Wood transaction
top
h39 panel,
typical
Wood worksurface
h64 Storage
cabinet, (2) file
drawers; cabinet
Pencil drawer with hinged glass
doors and 1adjust-
Box/box/file pedestal able shelf on top
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.42
FURNITURE CATALOG CUTS
DKSY81
Recommended Product Item: Desk, System B1
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada desk system
Finish: Maple techwood, silver
Size.: See draawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: See drawing
Description: Vivo desk system
Finish: Natural Maple recut veneer, metallic silver
Size.: See drawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: See drawing
Description: Compose desk system
Finish: Beachwood doublecut veneer, metallic silver
Size.:
Upholstery Mfg.:
Upholstery #:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.43
FURNITURE CATALOG CUTS
DKSY81
Desk, System B1
Box/box/file pedestal
Wood transaction
top
h39 panel
Wood worksurface
h64 Storage
cabinet, (2) file
drawers; cabinet
Pencil drawer with hinged glass
doors and 1adjust-
h49 panel able shelf on top
with wood transaction top
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.44
FURNITURE CATALOG CUTS
DKSY82
Recommended Product Item: Desk, System B2
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada desk system
Finish: V2 Burnt Walnut, 613 Silver
Size.: See draawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
DKSY82
Desk, System B2
Box/box/file pedestal
File/file pedestal
h39 panel,
wood
Wood worksurface
Pencil drawer
h39 panel, wood
with stone transaction top
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.46
FURNITURE CATALOG CUTS
DKSY83
Recommended Product Item: Desk, System B2b
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada desk system
Finish: V2 Burnt Walnut, 613 Silver
Size.: See draawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
DKSY83
Desk, System B2b
Box/box/file pedestal
File/file pedestal
h39 panel,
wood
Wood worksurface
Pencil drawer
h39 panel, wood
with stone transaction top
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.48
FURNITURE CATALOG CUTS
DKSY85
Recommended Product Item: Desk, System B3
Manufacturer: Halcon
Model No.: See drawing
Description: Abacus reception desk
Finish: Walnut, Quater Cut w/ clear stain, Spacer-Sycamore
Size.: See drawing
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Bernhardt
Model No.: See notes below
Description: Custom Stria reception desk
Finish: Walnut, Quater Cut w/ clear stain, Spacer-Sycamore
Size.: See drawing
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #2
Manufacturer: Gianni
Model No.: See drawing
Description: Custom reception desk
Finish: Walnut, Quater Cut w/ clear stain, Spacer-Sycamore
Size.: See drawing
Upholstery Mfg.: n/a
Upholstery #: n/a
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.49
FURNITURE CATALOG CUTS
DKSY85
Desk, System B3
Wood transaction
top
Pencil drawer
h68 wood vertical
storage cabinet, (2)
file drawers; cabinet
with hinged glass
doors and 2 adjust-
able shelf above
h36 panel
h68 wood vertical
Wood worksurface storage cabinet
Box/box file pedestal
File/file pedestal
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.50
FURNITURE CATALOG CUTS
DKSY86
Recommended Product Item: Reception Desk
Manufacturer: Halcon
Model No.: Custom see notes below
Description: Reception desk
Finish: Walnut cluster w/ clear stain, figured sycamore
Size.: See drawing
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer: Gianni
Model No.:
Description:
Finish:
Size.:
Upholstery Mfg.:
Upholstery #:
Notes:
Alternate Manufacturer #2
Manufacturer: CCN International
Model No.:
Description:
Finish:
Size.:
Upholstery Mfg.:
Upholstery #:
Notes:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.51
FURNITURE CATALOG CUTS
DKSY86
Desk, System B4
Elevation @ Credenza
Scale: 1:50
Plan @ Desk
Workstation
and Credenza
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.52
FURNITURE CATALOG CUTS
DKSY87
Recommended Product Item: Desk, System B5
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada desk system
Finish: Maple techwood, silver
Size.: See draawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
DKSY87
Desk, System B5
Open cabinet
with (1) adjustable shelf
File/file ped-
estal
Box/box/file
pedestal
h39 panel
Same components on both
d30 Wood sides
worksurface
Pencil drawer
Transaction top, stone
Note: provide accessory package per specification section 12000
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.54
FURNITURE CATALOG CUTS
DKSY90
Recommended Product Item: Desk, System A
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada desk system
Finish: Maple techwood, silver
Size.: See draawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: See drawing
Description: Vivo desk system
Finish: Natural Maple recut veneer, metallic silver
Size.: See drawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: See drawing
Description: Compose desk system
Finish: Beachwood doublecut veneer, metallic silver
Size.:
Upholstery Mfg.:
Upholstery #:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.55
FURNITURE CATALOG CUTS
DKSY90
Desk, System A
Open cabinet
with (1) adjustable shelf
d18 wood worksurface
h21 frosted
glass screen
h39 wardrobe
cabinet
h39 bookcases
(2 adj. shelves)
see BCS350
Common top,
see furniture
drawings
h49 panel,
spline only
d30 Wood Pencil drawer
worksurface
Pencil drawer
Box/box/file pedestal
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.56
FURNITURE CATALOG CUTS
DKSY91
Recommended Product Item: Desk, System A1
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada desk system
Finish: Maple techwood, silver
Size.: See draawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: See drawing
Description: Vivo desk system
Finish: Natural Maple recut veneer, metallic silver
Size.: See drawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: See drawing
Description: Compose desk system
Finish: Beachwood doublecut veneer, metallic silver
Size.:
Upholstery Mfg.:
Upholstery #:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.57
FURNITURE CATALOG CUTS
DKSY91
Desk, System A1
h49 panel,
spline only
d30 Wood Pencil drawer
worksurface
Pencil drawer
Mobile cart for card
storage - 35cm x 25cm
cards
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.58
FURNITURE CATALOG CUTS
DKSY92
Recommended Product Item: Desk, System A2
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada desk system
Finish: Maple techwood, silver
Size.: See draawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: See drawing
Description: Vivo desk system
Finish: Natural Maple recut veneer, metallic silver
Size.: See drawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: See drawing
Description: Compose desk system
Finish: Beachwood doublecut veneer, metallic silver
Size.:
Upholstery Mfg.:
Upholstery #:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.59
FURNITURE CATALOG CUTS
DKSY92
Desk, System A2
h49 panel,
spline only
d30 Wood Pencil drawer
worksurface
Pencil drawer
Box/box/file pedestal
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.60
FURNITURE CATALOG CUTS
DKSY93
Recommended Product Item: Desk, System A3
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada desk system
Finish: Maple techwood, silver
Size.: See draawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: See drawing
Description: Vivo desk system
Finish: Natural Maple recut veneer, metallic silver
Size.: See drawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: See drawing
Description: Compose desk system
Finish: Beachwood doublecut veneer, metallic silver
Size.:
Upholstery Mfg.:
Upholstery #:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.61
FURNITURE CATALOG CUTS
DKSY93
Desk, System A3
Open cabinet
with (1) adjustable shelf
d18 wood worksurface
h21 frosted
glass screen
Pencil drawer
Box/box/file pedestal
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.62
FURNITURE CATALOG CUTS
DKSY94
Recommended Product Item: Desk, System A4
Manufacturer: Knoll
Model No.: See drawing
Description: Autostrada desk system
Finish: Maple techwood, silver
Size.: See draawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #1
Manufacturer: Herman Miller
Model No.: See drawing
Description: Vivo desk system
Finish: Natural Maple recut veneer, metallic silver
Size.: See drawing
Upholstery Mfg.: Herman Miller
Upholstery #: To be determined
Alternate Manufacturer #2
Manufacturer: Haworth
Model No.: See drawing
Description: Compose desk system
Finish: Beachwood doublecut veneer, metallic silver
Size.:
Upholstery Mfg.:
Upholstery #:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.63
FURNITURE CATALOG CUTS
DKSY94
Desk, System A4
Open cabinet
with (1) adjustable shelf
d18 wood worksurface
h21 frosted
glass screen
h39 wardrobe
cabinet
h39 bookcases
(2 adj. shelves)
see BCS350
Common top,
see furniture
drawings
h49 panel,
spline only
d30 Wood Pencil drawer
worksurface
Pencil drawer
Box/box/file pedestal
Note: quantity of wardrobe cabinet and bookcases must be determined by drawings and field
conditions. Provide wardrobe cabinet if possible. See furniture drawings.
Plan @ Workstation
Scale: 1:50
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April, 2008 3.64
FURNITURE CATALOG CUTS
FIMF10
Recommended Product Item: Microfiche Cabinet, 10 Drawers
Manufacturer: Russ Bassett
Model No.: FL-10
Description: FL series 10 drawer michrofiche cabinet
Finish:
Size.: w43 1/8 d18 1/4 h56
Upholstery Mfg.: n/a
Upholstery #: n/a
Alternate Manufacturer #1
Manufacturer:
Model No.:
Description:
Finish:
Size.:
Upholstery Mfg.:
Upholstery #:
Notes:
Alternate Manufacturer #2
Manufacturer:
Model No.:
Description:
Finish:
Size.:
Upholstery Mfg.:
Upholstery #:
Notes:
Note #1: Field verify all areas prior to purchasing or installion of furniture.
Note #2: Images intended as reference only.
Ministry of Education Headquarters Building
30 April , 2008 3.65
4.0
4.0 Furniture Location Details
5.0
5.0 Room Furniture Details
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
5.14
5.15
5.16
5.17
5.18
5.19
5.20
5.21
5.22
5.23
5.24
5.25
5.26
5.27
5.28
5.29
5.30
5.31
5.32
5.33
5.34
5.35
5.36
5.37
5.38
5.39
5.40
5.41
5.42
5.43
5.44
5.45
5.46
5.47
5.48
5.49
5.50
5.51
5.52
5.53
5.54
5.55
5.56
5.57
5.58
5.59
5.60
5.61
5.62
5.63
5.64
5.65
5.66
5.67
5.68
5.69
5.70
5.71
5.72
5.73
5.74
5.75
5.76
5.77
5.78
5.79
5.80
5.81
5.82
5.83
5.84
5.85
5.86
5.87
5.88
5.89
5.90
5.91
5.92
5.93
5.94
5.95
5.96
5.97
5.98
5.99
5.100
5.101
5.102
5.103
5.104
5.105
5.106
5.107
5.108
5.109
5.110
5.111
5.112
5.113
5.114
5.115
5.116
5.117
5.118
5.119
5.120
5.121
5.122
5.123
5.124
5.125
5.126
5.127
5.128
5.129
5.130
5.131
5.132
5.133
5.134
5.135
5.136
5.137
5.138
5.139
5.140
5.141
5.142
5.143
5.144
5.145
5.146
5.147
5.148
5.149
5.150
5.151
5.152
5.153
5.154
5.155
5.156
5.157
5.158
6.0
6.0 Specification