Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
A 20 kV SWITCHGEAR
1 Manufacturer to be mentioned
2 Type Indoor metal clad
3 Highest system voltage kV 24
4 Rated basis insulation level kV 125
5 Rated one minute power frequency withstand voltage kV 50
6 Rated frequency Hz 50
7 Rated normal current A 630, 1250
8 Degree of protection IP 41
9 Materials of busbars Copper
10 Number of phase busbar 3
11 Number of neutral busbar : No
- for switchgear type A (general) 1
- for switchgear type B
12 Cross section of phase busbar sqmm
13 Cross section of neutral busbar sqmm
14 Rated continuous current of phase busbar A 2500
15 Rated cont. current of neutral busbar A 1000 (minimum)
16 Rated of short circuit kA, 1 sec 16
17 Insulation material for main busbar
18 Has the insulation material been flammability tested to IEC
60466 or other standard?
Page 1 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
Page 2 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
Page 3 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
C 20 kV CURRENT TRANSFORMER
i) 20 kV CURRENT TRANSFORMER
FOR INCOMING FEEDER
1 Manufacturer to be mentioned
2 Type indoor
3 Highest system voltage kV 24
4 Frequency Hz 50
5 Ratio, class, rated output:
a). For differential protection and for REF protection :
- ratio A 600-1200/5
- class 5P20
- output VA 30
b). For O/C and E/F protection :
- ratio A 600-1200/5
- class - 5P20
- output VA 30
c). For Instrument and metering :
- ratio A 600-1200/5
- class - 0.5
- output VA 40
6 Rated short time current kA, 1 sec 25
7 Knee point voltage V
8 Rated continuous thermal current A 2000
9 Weight kg
Page 4 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
2 Type indoor
3 Highest system voltage kV 24
4 Frequency Hz 50
5 Ratio, class, rated ouput ;
a). For O/C and E/F protection :
- ratio A 300-600/5
- class - 5P20
- output VA 30
b). For instrument and metering :
- ratio A 300-600/5
- class - 0.5
- output VA 40
6 Rated short time current kA,1 sec 25
7 Knee point voltage V
8 Rated continuous thermal current A 2000
9 Weight kg
Page 5 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
6 Class - 5P10
7 Weight kg
D 20 kV POTENTIAL TRANSFORMER
1 Manufacturer to be mentioned
2 Type
3 Highest system voltage kV 24
4 Frequency Hz 50
5 Ratio, class, output : V/V 20000:V3/100:V3/100:V3
for busbar and tap changer control, under-voltage relay : - 0.2
- ratio - 3P
- class of accuracy of secondary VA 100
- output of secondary VA 30
Page 6 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
6 Weight kg
7 Drawing No.
E PROTECTION
i) OVERCURRENT RELAY
1 Manufacturer to be mentioned
2 Type of overcurrent relay
3 Range of current settings
- Phase element % of CT rating
- Earth fault element % of CT rating
4 Range of timing settings at 10 x CT rating sec.
5 Burden of relay at 10 x CT rating sec.
6 Percentage of current setting at which relay will reset %
Page 7 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
4 Frequency range Hz
5 Frequency adjusment step Hz 0.1
6 Time delay range sec. 0.15-1.5
iv) AUTORECLOSE RELAY
1 Manufacturer to be mentioned
2 Type of relay
3 Number of reclosing shot
v) OVERVOLTAGE RELAY
1 Manufacturer to be mentioned
2 Type of relay
3 Number of stage
4 Voltage range V
5 Voltage adjustment step V
6 Time delay range sec.
vi) UNDERVOLTAGE RELAY
1 Manufacturer to be mentioned
2 Type of relay
3 Number of stage
4 Voltage range V
5 Voltage adjustment step V
6 Time delay range sec.
vii 20 kV LOAD BREAK SWITCH
1 Manufacturer to be mentioned
2 Type Indoor
3 Nominal voltage kV 20
4 Highest system voltage kV 24
5 Rated current A 400
Page 8 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
viii 20 kV FUSES
1 Manufacturer to be mentioned
2 Type
3 Nominal voltage kV 20
4 Highest system voltage kV 24
5 Rated current A 20
6 Current characteristic - Required
7 Weight kg
Page 9 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
- reset - Yes
- lamp test - Yes
13 To be installed into control cubicle as specified - Yes
G AC AMMETER
1 Manufacturer to be mentioned
2 Type
3 Quantity to be measured : A
- AC ( 3 phase, 1 Phase) 1 phase
4 Class of accuracy - 0.2
5 Range of indication A 0-1200; 0-2400
0-300 ; 0-600
6 Effective range
7 Rated operating conditions :
- rated current A 1
- rated voltage
- rated internal resistance
- rated resistivity of separate
resistance
- rated transformation ratio of CT A/A
- rated power consumption VA
8 Minimum creepage distance between live
conductor and earthed case
9 Protection degree IP54
10 Size mm 96x96
11 Type of instrument mechanism
12 Scale characteristics :
- scale length
Page 10 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
Page 11 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
Page 12 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
I WATTMETER
1. Manufacturer to be mentioned
2. Type
3. Quantity to be measured MW
- AC (3 phase, 1 phase) - 3 phase
- balanced Yes
- unbalanced Yes
- DC -
4. Class of accuracy 0.2
5. Range of indication MW As required
6. Effective range
7. Rating operating conditions :
- rated current A 1
- rated voltage V 110
- rated power consumption VAMax
- rated transformation ratio of : kV/kV 20:3/0.100:3
- voltage transformer A/A
- current transformer
- ohmic resistance of:
- current path
- voltage path
- inductance of current path
8. Minimum creepage distance
9. Protection degree IP54
10. Size mm 96 x 96
11' Type of instrument mechanism Electrodynamic
(number of watt/meter elements)
Page 13 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
J. VARMETER
1. Manufacturer to be mentioned
2. Type
3. Quantity to be measured MVAR
- AC (3 phase, 1 phase) - 3 phase
- balanced Yes
- unbalanced Yes
- DC -
4. Class of accuracy 0.2
5. Range of indication MVAR
6. Effective range
Page 14 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
Page 15 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
Page 16 of 17
No. DESCRIPTION UNIT REQUIRED PROPOSED AND GUARANTEE
Page 17 of 17