Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1 IM-1993
(REVISION OF ANSI B94.11-1979)
Twist Drills
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
I
Copyright ASME International
Provided by IHS under license with ASME Licensee=Bureau Veritas/5974260001, User=Rodriguez, Sergio
No reproduction or networking permitted without license from IHS Not for Resale, 05/28/2013 12:00:55 MDT
ASME B 9 4 . 1 1 N 9 3 W 0759670 0540651 071 m
Twist Drills
ASME B94.11M-1993
(REVISION OF ANSI B94.11-1979)
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
This Standard will be revisedwhen the Society approves the issuance of a new
edition. There will be no addenda or written interpretations of the requirements
of this Standard issued to this Edition.
This code or standard was developed under procedures accredited as meeting the criteria for
American National Standards. The Consensus Committee that approved the codeor standard was
balanced to assure that individuals from competent and concerned interestshave had anopportunity
to participate. The proposed code or standard was made available for public review and comment
which provides an opportunity for additionalpublic input from industry, academia, regulatory agen-
cies, and the public-at-large.
ASME does not "approve," "rate," or "endorse" any item, construction, proprietary device, or
activity.
ASME does not take any position with respect to the validity of any patent rights asserted in
connection with any items mentioned in this document, and does not undertake to insure anyone
utilizing a standard against liability for infringement of any applicable Letters Patent, nor assume
any such liability.Users of a codeor standard are expresslyadvised that determinationof the validity
of any such patentrights, and the risk of infringement of such rights, is entirely their own responsibility.
Participation by federal agency representative(s) or person(s) affiliated with industry is not to be
interpreted as government or industry endorsement of this code or standard.
ASME accepts responsibility for only those interpretationsissued in accordance with governing
ASME procedures and policies which preclude the issuance of interpretations by individual volun-
teers.
Copyright O 1994 by
THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS
All Rights Reserved
Printed in U.S.A.
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
FOREWORD
...
111
(The following is theroster of the Committee at the time of approval of this Standard.)
OFFICERS
E. J. Czopor, Chairman
E. W. McLaren, Secretary
COMMllTEE PERSONNEL
E. J. Czopor, E & S Sales, Inc., Bloomfield Hills, Michigan
M . E. Merchant, Metcut Res Associates, Inc., Cincinnati, Ohio
C. W. Preuss, Kingsford Broach and Tool, Inc., Westlake, Ohio
J. R. Strolberg, Rockton, Illinois
A. M. Bratkovich, Alternate, NMTBA, McLean, Virginia
V
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
CONTENTS
1 Scope .............................................................................................. 1
2 Twist Drills
2.1 NomenclatureandDefinitions ....................................................... 1
2.2 Classifications ............................................................................ 3
3 CombinedDrillsandCountersinks
3.1 NomenclatureandDefinitions ....................................................... 3
3.2 Applicable Twist DrillTerms ........................................................ 6
Figures
1 Identity of TwistDrillFeatures ............................................................ 2
2 Identity of CoreDrillFeatures ............................................................. 4
3 Identity of CombinedDrillandCountersinkFeatures ............................... 5
4 Dimensions of Fractional Size Twist Drills . High Speed Steel
(Silver and Deming Style) ................................................................. 49
Tables
1 General Dimensions of Straight Shank Twist Drills . Jobbers Length ........ 7
2 General Dimensions of Straight Shank Twist Drills . Taper Length
A . Through '/2 in . (12.7 mm) Dia....................................................... 16
B . Over ' / 2 in . (12.7 mm) Dia ............................................................. 21
3 General Dimensions of Straight Shank Twist Drills - Screw Machine Length
A . Through 1 in . (25.4 mm) Dia......................................................... 25
B . Over 1 in . (25.4 mm) Dia .............................................................. 33
4 General Dimensions of Tangs for Straight Shank Twist Drills ................... 34
5 General Dimensions of Taper Shank Twist Drills .................................... 35
6 Specifications and Definitions for Split Point Drill Grinding ..................... 48
7 General Dimensions of Three and Four Flute Straight Shank Core Drills .... 50
8 General Dimensions of Three and Four Flute Taper Shank Core Drills ....... 52
9 A . General Dimensions of Combined Drills and Countersinks
(Plain and Bell Types) .................................................................... 54
B . Tolerances of Combined Drills and Countersinks ............................... 55
10 Element Tolerances for High Speed Steel General Purpose
Twist Drills .................................................................................. 56
vii
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
TWIST DRILLS
(Straight Shank and Taper Shank Combined Drills and Countersinks)
--Axis- - -
web thickness - the thickness ofthe web at the point bell diameter - the diameter at the intersection of
unless another specific location is indicated the countersink portion and the bell portion at the
leading edge of the land
web thinning - the operation of reducing the web
thickness at the point to reduce drilling thrust body - the central portion of the body by which it
is held or driven
combined drill and countersink - single or double-
2.2 Classifications end cutting tool, havinghelical or straight flutes, and
2.2.1 Based on Kind of Shank having a drill portion and an adjacent integral coun-
tersink portion, primarilyused to produce centerholes
e straight shank drills -those having cylindrical shanks
which may bethe same or different diameter than the
body of the drill. The shank may be with or without
in work that will be held between machine centers
countersink angle - the included angle of the coun-
driving flats, tang, grooves or threads. tersink portion (it is normally 60 deg.)
taper shank drills - those having conicalshanks suit- countersink relief angle - the angle between a plane
able for direct fitting into tapered holes in machine a line tangent
at right angles to theaxis of the tool, and
spindles, driving sleeves, or sockets. Tapered shanks to the surface of the countersink portion at the in-
generally have a tang, which is used with a drift bar tersection of the countersink portion and the body
to eject the drill from its mating socket. and at theleading edge of the land. For thebell type,
the relief angle is measured at the intersection of the
2.2.2 Based on Number of Flutes bell portion and the body.
two-flute drills - the conventional typeof drill used
countersink portion - that part of the tool which
a
for originating holes
produces a conical bearing surface for the work cen-
three-flute drills (coredrills) - drills commonlyused ters. The bell type produces an additional secondary
for enlarging and finishing drilled, cast or punched conical section to provide clearance or protection for
holes. They will not produce original holes. the bearing surface.
four-flute drills (core drills) - used interchangeably drill diameter - the diameter of the drill portion
with three-flute drills. They are of similar construc- measured across the outer corners of the cutting lips
tion except for the number of flutes.
drill diameter relief - the relief provided on the land
2.2.3 Based on Hand of Cut of the drill portion to reduce contact with the walls
of the hole. It is generally of an eccentric form.
right-hand cut - when viewed from the cutting point,
the counterclockwise rotation of a drill in order to drill length - the length of the drill portion from the
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Drill diameter
L Tang
J h Ma,
rgin
4
Shank --Axis- -
diameter
Drill length--U
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Chisel edge
:int ang,l;xTrsink angle - Relief angle
is
CT
eter Cutting face 0
right-hand rotation
Bell Type
R
I
m
FIG. 3 IDENTITY OF COMBINED DRILL AND COUNTERSINK FEATURES
the countersink portion to produce clearance for the overall length-the lengthbetween the extreme points
point of a conical center of the tools
flutes - the helical or straight grooves cut or formed
in the cutting portions and the body
to provide cutting 3.2 Applicable Twist Drill Terms
edges on both the drill and countersink portions, to
permit removal of chips and to allow cutting fluidto For definitions, see para. 2.1.
reach the cutting lips chisel edge
chisel edge angle
flute length - the length from the outer corners of hlix angle
the cutting lips to the extreme ends of the flutes. It lips
includes the sweep of the tool used to generate the lip relief
flutesand,therefore,doesnotindicatetheusable
lip relief angle
length of flutes.
point angle
land - the peripheral drill and countersink portions web
between the adjacent flutes web thickness
6
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Millimeter
T Decimal
Inch
Equivalent
Millimeter
Equivalent
r Flute Length
F
mm
f Overall Length
L
mm
97 0.1 5 0.0059 0.1 50 1.6 19
96 0.16 0.0063 0.1 60 1.6 19
95 0.1 7 0.0067 0.170 1.6 19
94 0.1 8 0.0071 O. 180 1.6 19
93 0.1 9 0.0075 o. 190 1.6 19
80 0.0135 0.343 3 19
0.35 0.01 38 0.350 3 19
79 0.01 45 0.368 3 19
0.38 0.01 50 0.380 5 19
'/M 0.01 56 0.396 5 19
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Fraction No.
D
Ltr. Millimeter
T Decimal
Inch
Equivalent
Millimeter
Equivalent
t F
mm
-L
mm
- -
0.48 0.01 89 0.480 5 22
0.50 0.01 97 0.500 5 22
76 0.0200 0.508 5 22
75 0.021o 0.533 6 25
0.55 0.0217 0.550 6 25
74 0.0225 0.572 6 25
0.60 0.0236 0.600 8 29
73 0.0240 0.61O 8 29
72 0.0250 0.635 8 29
0.65 0.0256 0.650 10 32
71 0.0260 0.660 10 32
0.70 0.0276 0.700 10 32
70 0.0280 0.71 1 10 32
69 0.0292 0.742 13 35
0.75 0.0295 0.750 13 35
68 0.031 O 0.787 13 35
0.031 2 0.792 13 35
0.80 0.031 5 0.800 13 35
67 0.0320 0.813 13 35
66 0.0330 0.838 13 35
59 0.041O 1.O41 17 41
1.O5 0.0413 1.O50 17 41
58 0.0420 1.O67 17 41
57 0.0430 1.O92 19 44
1.10 0.0433 1.100 19 44
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Ltr.
-
Millimeter
r Decimal
Inch
Equivalent
0.0512
Millimeter
Equivalent
1.300
t
Flute Length
F
mm
22
F
Overall Length
-L
Inch
- mm
1 'I8 48
1.30
55 0.0520 1.321 22 1 al' 48
1.35 0.0531 1.350 22 1 'la 48
54 0.0550 1.397 22 1 al' 48
1.40 0.0551 1.400 22 1 'I0 48
9
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
O
TABLE 1 GENERAL DIMENSIONS OF STRAIGHT SHANK TWIST DRILLS -
JOBBERS LENGTH - FRACTIONAL, NUMBER, LETTER AND METRIC SIZES (CONT'D)
_____
Fraction No.
D
Ltr.
Diameter of Dr
Millimeter
i Decimal
Inch
Equivalent
Millimeter
.Equivalent
T
t -F
Flute Length
Inch
- mm
t Overall Length
mm
41 0.0960 2.438 I31~ 35 60
2.46 0.0965 2.450 I31~ 35 60
40 0.0980 2.489 I 31~ 35 60
2.50 0.0984 2.500 131~ 35 60
39 0.0995 2.527 131~ 35 60
29 0.1360 3.454 1% 44 73
3.50 0.1378 3.500 1% 44 73
28 0.1405 3.569 1 314 44 73
9 1 ~ 0.1406 3.571 1 3/4 44 73
3.60 0.1417 3.600 171~ 48 76
27 o.1440 3.658 1 7h 48 76
3.70 O.1 457 3.700 1 7b 48 76
26 0.1470 3.734 1 'Ia 48 76
25 0.1495 3.797 I71~ 48 76
3.80 0.1496 3.800 1 71s 48 76
10
a 19
4.1O
4.20
0.1614
O.1654
O.1660
4.1O0 54
4.200 54
4.216 54
2'1~
2v8
2v8
4.30 0.1693 4.300 2v8 54
18 0.1695 4.305 2% 54
' 1/64 0.1719 4.366 2'la 54
17 0.1730 4.394 56 23h6
14 0.1820 4.623 2% 6 56
13 4.70 0.1850 4.700 59 251'~
x 6 O.1875 4.762 25t' 6 59
4.80 12 O.1890 4.800 25/16 59
11 0.1 o91 4.851 251~6 59
5.1 O0 271'~ 62
5.1 05 271'~ 62
5.1 59 271'~ 62
5.182 2'12 64
5.200 2'12 64
5.220 2'12 64
5.300 2'12 64
5.309 2'12 64
5.400 2'12 64
5.41 O 2'12 64
5.500 2'12 64
5.558 2'12 64
5.600 251~ 67
5.613
5.700
11
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Ltr.
Diameter of Drill
Millimeter
r Decimal
Inch
Equivalent
Millimeter
Equivalent
t
Flute Length
mm
f Overall Length
L
mm
1 0.2280 5.791 67 98
5.80 0.2283 5.800 67 98
5.90 0.2323 5.900 67 98
A 0.2340 5.944 67 98
5/M 0.2344 5.953 67 98
12
T Decimal
Inch Millimeter T
Flute Length
F
f Overall Length
13
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Fraction No.
D
Ltr.
Diameter of Drill
Millimeter
Decimal
Inch
Equivalent
Millimeter
Equivalent
T
t
Flute Length
F
mm
f Overall Length
L
mm
'3/32 0.4062 10.31 7 98 133
Z 0.41 30 10.490 98 133
10.50 0.41 34 10.500 98 133
27/M 0.42 19 10.716 1O0 137
10.80 0.4252 10.800 103 140
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
13.20 0.5197 13.200 122 168
"I32 0.531 2 13.494 122 168
13.50 0.5315 13.500 122 168
13.80 0.5433 13.800 122 168
0.5469 13.891 122 168
3%d
14
D
Diameter of Drill
Decimal
Inch
1 Millimeter t Overall Length
I
Fraction No. Ltr. Millimeter Equivalent Equivalent I Inch mm
!
4'/64 0.6406 16.271
5% 6 132
16.50 0.6496 16.500 5%6 132
2'/32 0.6562 16.667
5% 6 132
16.75 0.6594 16.750 5Va 143 194
17.00 0.6693 17.000 551a 143 194
Fraction No.
D
Diameter of Drill
mm
T
Decimal
Inch
Equivalent
Millimeter
Equivalent
Flute Length
F
mm
f Overall Length
L
mm
1 .o0 0.0394 1 .o00 29 57
60 0.0400 1.016 29 57
59 0.041O 1 .O41 29 57
1 .O5 0.0413 1 .O50 29 57
58 0.0420 1 .O67 29 57
57
1.10
0.0430
0.0433
1 .O92
1.100
29
29
57
57
O
1.15 0.0453 1.150 29 57
56 0.0465 1.181 29 57
0.0469 1.1 91 29 57
54 0.0550 1.397 44 76
1.40 0.0551 1.400 44 76
1.45 0.0571 1.450 44 76
53
1.50 0.0591
0.0595
1.500
1.51 1
44
44
76
76
O
1.55 0.0610 1.550 44 76
0.0625 1.588 44 76
1.60 0.0630 1.600 51 95
52 0.0635 1.613 51 95
1.65 0.0650 1.650 51 95
16
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
i ASME B94.11M-1993
TWIST DRILLS
mm
r Decimal
Inch
Equivalent
Millimeter
Equivalent
t
Flute Length
mm
F Overall Length
1
mm
1.85 0.0728 1.850 51 95
49 0.0730 1.854 51 95
1.so 0.0748 1900 51 95
48 0.0760 1.930 51 95
1.S5 0.0768 1.950 51 95
0.0781 1.984 51 95
47 0.0785 1.994 57 108
2.00 0.0787 2.000 57 108
2.05 0.0807 2.050 57 1 08
46 0.0810 2.057 57 108
45 0.0820 2.083 57 1 08
2.10 0.0827 2.1 O0 57 1 08
2.1 5 0.0846 2.1 50 57 1 08
44 0.0860 2.1 84 57 1 08
2.20 0.0866 2.200 57 108
17
e
TABLE 2A GENERAL DIMENSIONS OF STRAIGHT SHANK TWIST DRILLS -
TAPER LENGTH - THROUGH '12 in. (12.7 mm) DIA.
FRACTIONAL, NUMBER, AND METRIC SIZES (CONT'D)
Fraction No.
D
Diameter of Drill
mm
Decimal
Inch
Equivalent
Millimeter
Equivalent
t Inch mm Inch mm
31 0.1 200 3.048 Z3/4 70 5% 130
3.1 O 0.1 220 3.1 O0 z3/4 70 5u 130
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
'h 0.1 250 3.175 23/4 5% 70 130
3.20 0.1 260 3.200 3 76 5% 137
30 0.1 285 3.264 3 76 53l8 137
O
3.30 0.1 299 3.300 3 76 5318 137
3.40 O. 1339 3.400 3 76 S3/0 137
29 O. 1360 3.454 3 76 5318 137
3.50 O. 1378 3.500 3 76 531e 137
28 O. 1405 3.569 3 76 5318 137
24
3.80
3.90
O. 1496
0.1 520
0.1 535
3.800
3.861
3.900
3
3
3
76
76
76
5%
53i8
578
137
137
137
O
23 0.1 540 3.912 3 76 5318 137
18
O
TABLE2AGENERAL DIMENSIONS OF STRAIGHT SHANK TWIST DRILLS -
TAPER LENGTH - THROUGH in. (12.7 mm) DIA. 'h
FRACTIONAL, NUMBER, AND METRIC SIZES (CONT'D)
r
Fraction No.
D
Diameter of Drill
mm
-r
Decimal
Inch
Equivalent
Millimeter
Equivalent
t
Flute Length
F
mm
f Overall Length
Inch
1
mm
12 4.80 0.1 890 4.800 92 6 152
11 0.1910 4.851 92 6 152
4.90 0.1 929 4.900 92 6 152
10 0.1 935 4.91 5 92 6 152
9 0.1 960 4.978 92 6 152
l
1. 3
5.40
5.50
0.21 26
0.21 30
0.21 65
5.400
5.41 O
5.500
92
92
92
6
6
6
152
152
152
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
0.21 88 5.558 92 6 152
5.60 0.2205 5.600 95 6'Is 156
19
Fraction No.
D
Diameter of Drill
mm
Decimal
Inch
Equivalent
Millimeter
Equivalent
t
Flute Length
F
mm
f Overall Length
L
mm
7.80 0.3071 7.800 1 02 162
0.3125 7.938 102 162
8.00 0.3150 8.000 105 165
8.20 0.3228 8.200 105 165
0.3281 8.334 105 165
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
0.3438 8.733 105 165
8.80 0.3465 8.800 108 171
9.00 0.3543 9.000 108 171
0.3594 9.1 29 108 171
20
Chamfer
1
rs1 I
Nominal shank
size is same as nominal drillTable
See
size 10 for tolerances
drill
Frac. mm
-
12.80
D
Diameter of Drill
Decimal
Inch
Equiv.
0.5039
Overall
Milli-
meter
Equiv.
12.800
Flute
mm
121
I Inch
8
I mm
203
I 5 -
-
4%
length Maximum
of Body
Inch -
B -
mm
124
Minimum
Inch
251~
mm
66
Inch
'I2
mm
13
13.00 0.51 18 13.000 121 8 203 4% 124 2518 66 'I2 13
33/64 0.5156 13.096 121 8 203 4% 124 251~ 66 'I2 13
13.20 0.51 97 13.200 121 , 8 203 471a 124 25h 66 'I2 13
?h2 0.5312 13.492 121 8 203 41'0 124 25h 66 'I2 13
21
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
f
Flute Overall Length Maximum
Minimum
Diameter of Drill
mm Equiv.
r Milli-
meter
Equiv.
t
--
Length
Inch -
-
F
mm Inch
L
Length
mm
-
of Body
B
Inch -
- mm
~
mm Inch mm
0.6562 16.667 5% 130 9 229 5% 133 79 51~ 16
16.75
0.6594 16.750 5% 137 9% 235 5% 140 79 51~ 16
0.6693
17.00 17.000 137 9% 235 5% 140 79 51~ 16
0.671 9 17.066 53/6 137 9% 235 5% 140 79 5/E 16
0.6791
17.25 17.250 53/6 137 9% 235 5% 140 79 5 / ~ 16
18.50
0.7283 18.500 5% 149 9% 248 6 152 79 51~ 16
0.7344 18.654 5% 149 248 9%6 152 79 5/s 16
19.00
0.7480 19.000 5% 149 93l4 248 6 152 79 51~ 16
0.7500 19.050 5% 149 93l4 248 6 152 79 51~ 16
0.7656 19.446 6 152 9% 251 6% 156 79 51~ 16
0.7677
19.50 19.500 6 152 91'8 251 6% 156 79 518 16
0.781 2 19.842 6 152 91'0 251 6% 156 79 51~ 16
20.00
0.7874 20.000 6% 156 10 254 61
'4 159 79 51~ 16
0.7969 20.241 6% 156 10 254 61
'4 159 79 51~ 16
20.50
0.8071 20.500 6% 156 10 254 6V4 159 79 5/s 16
23.00
0.9055 23.000 6% 156 10 254 6V4 159 79 51~ 16
0.9062 23.017 6% 156 10 254 61
'4 159 79 51~ 16
0.92 19 23.41 6 6% 156 103/4 273 6V4 159 98 51~ 16
23.50
0.9252 23.500 6% 156 103h 273 61
'4 159 98 5!s 16
0.9375 23.81 2 6% 156 103/4 273 6 159 98 518 16
24.00
0.9449 24.000 6% 162 11 279 6% 165 98 51~ 16
0.9531 24.209 6% 162 279 116% 165 98 51~ 16
24.50
0.9646 24.500 6% 162 11 279 6% 165 98 51~ 16
0.9688 24.608 61' 6 162 11 279 6% 165 98 5/9 16
25.00
0.9843 25.000 63/8
- 162
- 11 279 -6% 165
- 98 510 16
22
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
D
Diameter of Drill
mm
-
F
lecimal
Inch
Equiv.
0.9844
Milli-
meter
Equiv.
25.004
r
i-
Flute
Length
F ~
mm
-
162
Overall
Length
L -
-mm
279
Length
of Body
B -
mm
-
165
Minimum
Length of Shank
S
mm
98
F Maxirnum
Length of Neck
Inch
51~
N
mm
16
1.o000 25.400 162 279 165 98 51~ 16
!5.50 1.O039 25.500 165 283 168 98 51~ 16
1.O1 56 25.796 165 283 168 98 51~ 16
Z6.00 1.O236 26.000 165 283 168 98 51~ 16
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
1.0781 27.384 175 292 178 98 51~ 16
27.50 1.0827 27.500 175 292 178 98 51~ 16
1.0938 27.783 175 292 178 98 51~ 16
28.00 1.1024 28.000 181 298 184 98 5
h 16
1.1094 28.1 79 181 298 184 98 510 16
I
28.50 1.1220 28.500 181 298 184 98 510 16
1.1 250 28.575 181 298 184 98 51~ 16
1.1406 28.971 184 302 187 98 51~ 16
29.00 1.14J7 29.000 184 302 187 98 51~ 16
1.1 562 29.367 184 302 187 98 51~ 16
23
O
TABLE 2B GENERAL DIMENSIONS OF STRAIGHT SHANK TWIST DRILLS -
-
TAPER LENGTH OVER h in. (12.7 mm) DIA.
FRACTIONAL AND METRIC SIZES (CONTD)
D
Diameter of Drill
mm
T Decimal
Inch
1.3750
Milli-
meter
Equiv.
34.925
T Flute
Length
Equiv.
F
mm
225
Overall
Length
Inch
14%
L
mm
368
F Length Maximum
of Body
B-
mm
-
229
Minimum
Inch
418
Inchmm
124 518
mm
16
35.00 35.000 1.3780 229 14% 371 232 418 124 51~ 16
35.50 35.500 1.3976 229 145h 371 232 4% 124 5/s 16
36.00 1.4173
35.717 1.4062
36.000
229
232
14%
14%
371
375
232
235
4%
418
124
124
51~
5h
16
16 O
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
24
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
See Table 10 for tolerances
conical point may be used at the
manufacturer's option.
Fraction No.
D
Ltr.
Diameter of Dr
mm
i Decimal
Inch
Equivalent T Millimeter
Equivalent
t Flute Length
F
mm
t Inch
L
mm
1 .o0 0.0394 1,000 13 I 3/s 35
60 0.0400 1.016 13 I 31~ 35
59 0.041O 1 .O41 13 1 3/E 35
1 .O5 0.0413 1 .O50 13 I 3/s 35
58 0.0420 1 .O67 13 I 3/a 35
.O
1.35 0.0531 1.350 16 41
54 0.0500 1.397 16 I5 1 ~ 41
1.40 0.0551 1.400 16 I51~ 41
1.45 0.0571 1.450 16 1 41
1.50 0.0591 1.500 16 1 5/s 41
53 0.0595 1.511 16 I5 1 ~ 41
25
Fraction No.
D
Ltr. mm
T Decimal
Inch
Equivalent
Millimeter
Equivalent
t F
mm
L
mm
1.70 0.0669 1.700 17 43
51 0.0670 1.702 17 43
1.75 0.0689 1.750 17 43
50 0.0700 1.778 17 43
1.80 0.0709 1.800 17 43
0.0781 1.984 17 43
47 0.0785 1.994 17 43
2.00 0.0787 2.000 17 43
2.05 0.0807 2.050 19 44
46 0.081O 2.057 19 44
45 0.0820 2.083 19 44
2.10 0.0827 2.100 19 44
2.1 5 0.0846 2.1 50 19 44
44 0.0860 2.184 19 44
2.20 0.0866 2.200 19 44
0.0938 2.383 19 44
2.40 0.0945 2.400 21 46
41 0.0960 2.438 21 46
2.45 0.0965 2.450 21 46
40 0.0980 2.489 21 46
38 0.1015 2.578 21 46
2.60 0.1 024 2.600 21 46
37 0.1 040 2.642 21 46
26
mm
Decimal
Inch
Equivalent
Millimeter
Equivalent
t
Flute Length
F
mm
f Overall Length
L
mm
34 0.1110 2.81 9 22 48
33 0.1 130 2.870 22 48
2.90 0.1 142 2.900 22 48
32 0.1 160 2.946 22 48
3.00 0.1 181 3.000 22 48
31 0.1200 3.048 22 48
3.10 0.1220 3.1O0 22 48
O. 1250 3.175 22 48
3.20 O. 1260 3.200 24 49
30 0.1285 3.264 24 49
O. 1562 3.967 25 52
22 0.1 570 3.988 27 54
4.00 0.1 575 4.000 27 54
21 O. 1 590 4.039 27 54
20 0.1610 4.089 27 54
0.1719 4.366 27 54
17 0.1 730 4.394 29 56
4.40 0.1 732 4.400 29 56
16 0.1770 4.496 29 56
4.50 0.1772 4.500 29 56
27
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
D I Decimal
Inch -Millimeter
F L
Equivalent Equivalent Inch mm Inch mm
0.1800 4.572 1 118 29 2% 6 56
0.1 181 4.600 1 '/S 29 23116 56
0.1820 4.623 1 '/S 29 56 23h
0.1850 4.700 1 '/S 29 23116 56
0.1875 4.762 1 '/S 29 56 23h
28
O
TABLE 3A GENERAL DIMENSIONS OF STRAIGHT SHANK TWIST DRILLS -
SCREW MACHINE LENGTH THROUGH 1 in. (25.4 mm) DIA. -
FRACTIONAL, NUMBER, LETTER AND METRIC SIZES [CONT'D)
~~
t
Diameter of Dril Flute Length Overall Length
Decimal
D Inch Millimeter -F L
Fraction No. Ltr. mm Equivalent Equivalent Inch mm mm
-
6.40 0.2520 6.400 1 7116 37 67
6.50 0.2559 6.500 1 ~116 37 67
a F
G
6.60
0.2570
0.2598
0.261O
6.528
6.600
6.629
1 7116
17h
1 7116
37
37
37
67
67
67
O '132
7.20
7.30
0.2812
0.2835
0.2874
7.142
7.200
7.300
1 112
1
1 gil 6
38
40
40
68
70
70
L 0.2900 7.366 1 91'6 40 70
7.40 0.2913 7.400 1 91' 6 40 70
O
29
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
O
TABLE 3A GENERAL DIMENSIONS OF STRAIGHT SHANK TWIST DRILLS -
-
SCREW MACHINE LENGTH THROUGH 1 in. (25.4 mm) DIA.
FRACTIONAL, NUMBER, LETTER AND METRIC SIZES (CONT'D)
Fraction No.
1
Ltr.
Diameter of Drill
mm
Decimal
Inch
Equivalent
Millimeter
Equivalent
f Flute Length
F
mm
f Overall Length
L
mm
R 0.3390 8.61 1 43 76
8.70 0.3425 8.700 43 76
0.3438 8.733 43 76
S
8.80 0.3465
0.3480
8.800
8.839
44
44
78
78 O
8.90 0.3504 8.900 44 78
9.00 0.3543 9.000 44 78
T 0.3580 9.093 44 78
9.1 o 0.3583 9.1 O0 44 78
0.3594 9.1 29 44 78
V
9.60
0.3750
0.3770
0.3780
9.525
9.576
9.600
46
48
48
79
83
83
O
9.70 0.381 9 9.700 48 83
9.80 0.3858 9.800 48 83
W 0.3860 9.804 48 83
9.90 0.3898 9.900 48 83
0.3906 9.921 48 83
10.00 0.3937 10.000 49 84
X 0.3970 10.084 49 84
O
30
O
TABLE 3A GENERAL DIMENSIONS OF STRAIGHT SHANK TWIST DRILLS -
SCREW MACHINE LENGTH - THROUGH 1 in. (25.4 mm) DIA.
FRACTIONAL, NUMBER, LETTER AND METRIC SIZES (CONT'D)
r
-
No.
- Ltr.
-
Diameter of Drill
mm
r Decimal
Inch
Equivalent
Millimeter
Equivalent
t -F
Flute Length
Inch
- mm
f Overall Length
L
mm
12.20 0.4803 12.200 23/16 56 94
0.4844 12.304 231'6 56 94
12.50 0.4921 12.500 2 'I4 57 95
O 12.80
0.5000
0.5039
12.700
12.800
21'4
23~
57
60
95
98
a 14.50
14.75
0.5709
0.5781
0.5807
14.500
14.684
14.750
15.000
25/a
2510
25/s
251~
67
67
67
67
105
105
105
105
15.00 0.5906
0.5938 15.083 2 51a 67 105
O 16.75
0.6562
0.6594
16.667
16.750
2JA
27h
73
J3
114
117
17.00 0.6693 17.000 2JI8 73 117
0.6719 17.066 271~ 73 117
17.25 0.6791 17.250 2718 73 117
0.6875 17.462 2'18 73 117
31
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
No.
D
Ltr.
Diameter of Drill
mm
T Decimal
Inch
Equivalent
Millimeter
Equivalent
t
Flute Length
F
mm
f Overall Length
L
mm
0.7344 18.654 79 127
19.00 0.7480 19.000 79 127
0.7500 19.050 79 127
0.7656 19.446 83 130
19.50 0.7677 19.500 83 130
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
0.921 9 23.41 6 95 146
23.50 0.9252 23.500 95 146
0.9375 23.81 2 95 146
24.00 0.9449 24.000 98 1 49
32
Decimal
A
33
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Over '732 through Over 11.91 through 14.29 0.303 0.297 7.70 7.55 12.5
Over %6 through *'/Jz Over 14.29 through 16.67 0.373 0.367 9.47 9.32 14.5
Over 21/32 through 3/4 Over 16.67 through 19.05 0.443 0.437 11.25 11.10 16.0
Over 3/4 through 718 Over 19.05 through 22.23 0.51 4 0.508 13.05 12.90 17.5
Over S
/' through 1 Over.22.23 through 25.40 0.609 0.601 15.47 15.27 19.0
Over 1 through 13/16 Over 25.40 through 30.16 0.700 0.692 17.78 17.58 20.5
Over 1 3 h through 13h Over 30.16 through 34.93 0.81 7 0.809 20.75 20.55 22.0
NOTE:
(1)Tofit split sleeve collet type drill drivers, see ANSI 894.35
Concentricity of Tang
Thickness of Tana (TI I Total
Indicator
Variation TT.I.V.P
I I I
~~~~~~
NOTE:
(1)Method of measurement: Place shank of drill in V-block, level the tang surface. Set the tip of the dial
indicator on the tang and set the indicator to zero. Rotate the drill 180 deg.and note the indicator
reading.
34
f
f- Taper shank dimensions and tolerances
in accordance with
American
National See
Table 10 for drill
tolerances
Standard 85.10, Machine Tapers.
Diam, er of Drill
FRACTIONAL AND METRIC SIZES
r
i
Regular Shank (Note 1)
Fraction
D
Millimeters
3.00
Decimal
Inch
Equivalent
0.1 181
Millimeter
Equivalent
3.000
Morse
Taper
Number
A
1
Inch
1JI8
Flute Length
F
Millimeters
48
I Overall Length
L
Millimeters
130
0.1250 3.175 1 1JI8 48 130
3.20 0.1 260 3.200 1 2118 54 137
3.50 O. 1378 3.500 1 2'/8 54 137
O. 1406 3.571 1 21
'8 54 137
a 3.80
4.00
4.20
O. 1496
O. 1 562
O. 1 575
O. 1654
3.800
3.967
4.000
4.200
1
1
1
1
2110
2'I0
21
'2
2112
54
54
64
64
137
137
146
146
0.1719 4.366 1 2'12 64 146
O 6.00
0.2344
0.2362
5.954
6.000
1
1
2718
2%
73
73
156
156
6.20 0.2441 6.200 1 2% 73 156
0.2500 6.350 1 2JI8 73 156
6.50 0.2559 6.500 1 3 76 159
0.2656 6.746 1 3 76 159
NOTE:
(1) No shanks smaller or larger than regular are used for these sizes.
35
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Millimeters
7.80
'i Decimal
Inch
Equivalent
0.2969
0.3071
Millimeter
Equivalent
7.541
7.800
Morse
Taper
Number
A
1
1
Flute Length
F
Millimeters
79
79
I Overall Length
Inch
6318
6318
L
Millimeters
162
162
I
0.31 25 7.938 1 79 6310 162
8.00 0.31 50 8.000 1 83 6 '12 165
8.20 0.3228 8.200 1 83 6% 165
36
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
F c
T
~~
Morse Morse I
Flute Length
t Overall Length Flute Length Overall Length
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
laper
Number
A Inch
F
Millimeters Inch
L
Millimeters
Taper
Number
A Inch
F
Millimeters
t Inch
L
Millimeters
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... .*. ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... 2 3 '12 89 7% 187
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... 2 4% 105 8 203
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... 2 4'18 105 8 203
1 4% 111 73/4 197 .,. ... ... ... ...
37
Fraction
D
Millimeters
Decimal
Inch
Equivalent
Millimeter
Equivalent
Morse
Taper
Number
A Inch
Flute length
F
Millimeters
F Overall Length
Inch
L
Millimeters
1
38
Morse
Taper
Number
A
1
F
4
'
1
s
Shank Smaller Than Regular
Inch
Flute Length
F
Millimeters
124
I"--+
Overall Length
Inch
8'14
L
Millimeters
210
i
Morse
Taper
Number
A
...
Inch
...
...
Shank Larger Than
Flute Length
F
Millimeters
...
...
!gular
Overall Length
Inch
L
Millimeters
...
1 4% 124 8114 21 o ... ... ...
1 4% 124 8'14 21 o ... ... ... ... ...
1 4% 124 8l14 21 o ... ... ... ... ...
1 4'1s 124 8'14 21 o ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
f . . ... ... ... ... ... ... ... .,. ...
... ... ... ... ... ... ... ... ... ..*
... ... ... ... ... ... f . . ... ... ...
... *,. ... ... ... ... ... ... ... ...
... .*. ... .,. ... ... ... ... ... ...
... ... ... ... ... 3 5'18 130 93/4 248
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... 3 5'18 130 9% 248
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... 3 5% 137 10 254
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... 3 5% 137 10 254
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... 3 5% 143 1 0'14 260
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... 3 5% 143 10% 260
... . f . ... ... ... ... ... ... ... ...
39
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
O
TABLE 5 GENERAL DIMENSIONS OFTAPER SHANK TWIST DRILLS
FRACTIONAL AND METRIC SIZES (CONT'D)
Diameter of Drill T Reaular Shank T
D
Millimeters
Decimal
Inch
Equivalent
Millimeter
Equivalent
Morse
Taper
Number
A Inch
Flute Length
F
Millimeters
5 Overall Length
1
Millimeters
21 .o0 0.8268 21.o00 3 6% 156 273
0.8281 21 .O34 3 6% 156 273
0.8438 21.433
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
3 6% 156 273
21.50 0.8465 21.500
0.8594 21.829
3
3
6%
6'8
156
156
273
273 O
22.00 0.8661 22.000 3 6% 156 273
0.8750 22.225 3 6% 156 273
22.50 0.8858 22.500 3 6% 156 273
0.8906 22.621 3 6'1s 156 273
23.00 0.9055 23.000 3 6% 156 273
24.50
25.00
0.9531
0.9646
0.9688
0.9843
24.209
24.500
24.608
25.000
3
3
3
3
6%
63k
6%
6%
162
162
162
162
279
279
279
279
a
0.9844 25.004 3 63/8 162 279
27.50
1.0781
1.O827
1.O938
27.384
27.500
27.783
4
4
6%
67k
175
175
318
318
a
4 671s 175 318
28.00 1.1024 28.000 4 7 118 181 324
1.1094 28.179 4 7% 181 324
28.50 1.1220 28.500 4 7% 181 324
1.1250 28.575 4 71
'8 181 324
1.1406 28.971 4 7% 184 327
29.00 1.1417 29.000 4 7114 184 327
1.1 562 29.367 4 7114 184 327
29.50 1.1614 29.500 4 73h 187 330
40
Inch
10
L
lllillimeters
254
Morse
Taper
Number
A
F Inch
...
Flute Length
F
Millimeters
...
Overall Length
Inch
...
L
Millimeters
... ... ... ... ... ... ... ... ... ...
... f . . ... ... ... ... ... ... ... ...
... f . . ... ... ... 4 6518 168 121'4 31 1
... ... ... ... ... ... ... ... ... ...
3 6718 175 11112 292 ... ... ... ... ...
41
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
42
O
TABLE 5 GENERAL DIMENSIONS OF TAPER SHANK TWIST DRILLS
FRACTIONAL AND METRIC SIZES (CONTD)
Shank Smaller Than Regular
i
Shank Larger Than egular
Morse
Taper
Number
A
-7
t
Inch
Flute Length
F
Millimeters
Overall Lenath
Inch
L
Millimeter!
Morse
Taper
Number
A Inch
Flute Length
F
Millimeters Inch
Overall Lenath
L
Millimeters
3 7Ya 187 12 305 ... ... .. ...
3 7318 187 12 305 ... ... ... ...
3 7318 187 12 305 ... ... ... ...
3 7112 190 12118 308 ... . f . ... ...
3 7112 190 12118 308 ... ... ... ...
3 712 190 1 2110 308 ... ... ... . f . ...
3 7% 200 1 212 318 ... ... ... ... ...
3 718 200 1212 318 ... ... ... ... ...
3 7718 200 12/2 318 ... ... ... ... ...
3 710 200 1 212 31 8 ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... . f . ... ... ... ... ... *..
... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... .,. ... ... ... ...
... ... ... ... ... ... ... ... ...
... ... f . . ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ... ...
... ... ... ... ... ... ... ... ...
... ... ... ... ... ... . f . ... ...
... ... ... ... ... ...
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
43
F
~~
Morse
Taper Flute Length Overall Length
Decimal
D Inch Millimeter Number F L
Millimeters Equivalent Equivalent A Inch Millimeters Inch Millimeters
1.5312 38.892 5 93h 238 16310 41 6
39.00 1.5354 39.000 5 95h 244 16% 422
1.5469 39.291 ... ... ... ... ...
1.5625 39.688 5 95h 244 16% 422
40.00 1.5748 40.000 5 9% 251 1 6% 429
44
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
c
FRACTIONAL AND METRIC SIZES (CONTD)
. .
Shank Smaller Than Regular Shank Larger Than Regular
I F I
~
Morse Morse
Taper
Number
Flute Length
F
Overall Length
L
c
1
Taper
Number
Flute Length Overall Length
F t L
f
.A Inch .
.
Millimeters
.. Inch Hillimeters .
.
A Inch Millimeters Inch Millimeters
4 9318 238 15 38I ... ... ... ... ...
4 g5/a 244 1514 387 ... ... ... ... ...
4 9518 244 1514 387 ... ... f . . ... ...
4 9518 244 15114 387 ... ... ... ... ...
4 9% 251 15k 394 ... ... ... ... ...
4 g7/8 25 1 15k 394 ... ... ... ... ...
4 9718 25 1 1 512 394 ... ... ... ... ...
4 10 254 15518 397 ... ... ... ... ...
4 10 254 1S5/a 397 ... ... ... ... ...
4 10 254 15518 397 ... ... ... ... ...
45
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
r
!
Fraction
D
Millimeters
Decimal
Inch
Equivalent
2.0938
Millimeter
Equivalent
53.1 83
Morse
Taper
Number
A
5
F Flute Lenath
F
Millimeters
260
Inch
17%
Overall Length
L
Millimeters
441
2.1 250 53.975 5 260 17318 441
54.00 2.1 260 54.000 5 260 17% 441
2.1 562 54.767 5 260 17318 441
55.00 2.1 654 55.000 5 260 17318 441
NOTE:
(1)No shanks smaller or larger than regular are used for these Sim.
46
L
2.2500
3.5000 i 82.550
88.900 L I
1 51'2
...
1
394
...
1 I
648
3.5000 i
78.000
79.375
82.550
88.900
5
5
5
5
I 362
362
387
41 3
22
22
22
24
559
559
584
610.
47
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
m 3 deg. - 8 deg.
"
(1) Dress notching wheelto 110 deg. angle, plus or minus 5 deg.
(2) Shading represents areas ground during split pointing.
A
' 'k"9Odeg. \
50 deg.
+ 10
- 0
I - /'
~~~
Over ~~
'/8-l/4
~
I
.
dea.*2
14 dea. I dea.+2
14 dea. I .O02
T.I.V. I .002/.005 I .O10 I .O03 I .O02
Over l/4-l/2 12 deg.k2 deg. 12 deg.k2 deg. .O02 T.I.V. .002/.009 .O1 5 .O04 .O04
' / ~ ~ / 4 10 deg.+2 des.
12 deq.*2 den. Over .O04 T.I.V. .003/.012 .o20 .O05 .O04
~ ~
Over 3/4-1
~~~~~~
I 11 dea.h2 dea. I dea.*2
8 dea. I .O04
T.I.V. I .005/.020 I .O25 I .O07 I .O04
GENERAL NOTE: Source NAS 907, 14 Feb. 1986, pp. 15 and 16.
48
'
0.500
'
I Y
- - - L
IL2.25."
49
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
x
E
3
\
i -
*
"
118 deg.
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
- F
L
* Drill diameter 11/32 in. (8.733 mm) and smaller
*
r L diameter
Drill diameter 3/8 in. (9.525 mm) and larger
Nominal shank
is
size same as nominal drill size See Table 10tolerances
for
TABLE 7 GENERAL DIMENSIONS OF THREE AND FOUR FLUTE STRAIGHT SHANK CORE DRILLS
FRACTIONAL SIZES ONLY
Diameter of Drill l- Three Flute Four Flute
Decimal
Inch
Equivalent
Millimeter
Equivalent
F Flute Length
Inch
F
Millimeters
f Overall Length
Inch
L
Millimeters
F Inch
Flute Lenath
F
Millimeters
f Overall Lentlth
Inch
L
Millimeters
0.2500 6.350 3% 95 61
'0 156 ...
0.281 2 7.142 37h 98 61
'4 159 ... ...
0.3125 7.938 4 102 6% 162 ... ... ... ...
0.3438 8.733 4% 105 61
'2 165 ... ... ... ...
0.3750 9.525 4% 105 6% 171 ... ... ... ...
0.4062 10.31 7 43h 111 7 178 ... ... ... ...
0.4375 11.112 45h 117 7114 184 ... ... ... ...
0.4688 1 1.908 4% 121 7% 190 ... ... ... ...
0.5000 12.700 4314 121 7314 197 4314 121 7314 197
0.5312 13.492 4314 121 8 2 03 4314 121 8 203
50
TABLE 7 GENERAL DIMENSIONS OF THREE AND FOUR FLUTE STRAIGHT SHANK CORE DRILLS
FRACTIONAL SIZES ONLY (CONT'D)
Diameter of Drill l- Three Flute Four Flute
D
Inches
71~
29/32
Decimal
Inch
Equivalent
0.8750
0.9062
Millimeter
Equivalent
22.225
23.017
Inch
...
...
i T
Flute Length
F
Millimeters
...
...
Overall Length
...
L
Inch
Flute Length
6lIa
6%
F
Millimeters
156
156
Overall Length
Inch
10
10
L
Millimeters
2 54
2 54
15h 0.9375 23.812 ... ... 6% 156 103/4 273
3'/32 0.9688 24.608 ... ... 63/a 162 11 279
1 1.o000 25.400 ... ... 63/s 162 11 279
51
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
TABLE 8 GENERAL DIMENSIONS OF THREE AND FOUR FLUTE TAPER SHANK CORE DRILLS
FRACTIONAL SIZES ONLY
T-
~
Decimal
Inch
Equiv.,
0.2500
mm
Equiv.
6.350
Morse
Taper
Number
A
1
F Flute Length
Inch
2710
F -
mm
-
73
f
Overall Length
L -
mm
-
156
Morse
Taper
Number
A
...
I Flute Lenath
Inch
...
F
mm
...
Overall Length
Inch
L
mm
...
0.2812 7.1 42 1 3 76 159 ... ... ... ...
0.3175 7.938 1 31'0 79 162 ... ... f . . ...
0.3438 8.733 1 31'4 83 165 ... ... ... ...
0.3750 9.525 1 3 '12 89 171 ... ... ... ...
0.8750 22.225 3 61
's 156 273 3 6% 156 273
0.9062 23.000 3 6% 156 273 3 6% 156 273
0.9375 23.81 2 3 6% 156 273 3 6% 156 273
0.9688 24.608 3 63/s 162 279 3 63h7 162 279
1.o000 25.400 3 63/s 162 279 3 63L3 162 279
-
- -
52
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
TABLE 8 GENERAL DIMENSIONS OF THREE AND FOUR FLUTE TAPER SHANK CORE DRILLS
FRACTIONAL SIZES ONLY (CONT'D)
Decimal
Inch
Equiv.
mm
Equiv.
Morse
Taper
Number
A
F Flute Length
Inch
F
mm
f
Overall Length
Inch
L
mm
-
i F Morse
Taper
Number
A
Flute Length
Inch
F -
mm
-
f
Overall Length
L
mm
-
1.0312 26.192 3 6% 165 1 110 283 3 6% 165 283
1.0625 26.988 3 61's 168 11'14 286 3 6% 168 286
1.O938 27.783 4 6JJs 175 12% 318 4 6% 175 318
1.1250 28.575 4 7'1s 181 12% 324 4 7% 181 324
1.1 562 29.367 4 7% 184 12% 327 4 7% 184 327
1.6562 42.067 ... ... ... ... ... 5 10'10 257 435
1.6875 42.862 ... ... ... ... ... 5 10'10 2 57 435
1.8438 43.658 ... ... ... ... ... 5 10'10 257 435
... ... ... ... ...
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
1.7500 44.450 5 1O'h 257 435
1.781 2 45.262 ... ... ... ... ... 5 1O'h 257 435
1.8125 46.038 ... ... ... ... ... 5 10% 257 435
1.o000 46.833 ... ... ... ... .,. 5 10'/8 257 435
1.8750 47.625 ... ... ... ... ... 5 10310 264 441
1.9062 48.41 7 ... ... ... ... ... 5 103h 264 441
1.9375 49.21 2 ... ... ... ... ... 5 103h 264 441
1.9688 50.008 ... ... ... ... ... 5 10% 264 441
2.0000 50.800 ... ... ... ... ... 5 1031~ 264 441
2.1250 53.975 ... ... ... ... ... 5 10% 260 441
2.2500 57.1 50 ... ... ... ... ... 5 10% 2 57 441
2.3750 60.325 ... ... ... ... ... 5 1O'h 2 57 441
53
A I rA O
I
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Plain Type
I Body Diameter
f Drill Diameter
f Drill Length
f Overall Length
-r
A D C L
Millimeters Inches Millimeters Inches Millimeters Inches Millimeters
2.38 0.64 .O30 0.76 1'Ia 29
2.38 0.79 .O38 0.97 1'la 29
3.1 8 1.19 3/64 1.19 1% 32
'Il 6 4.76 1.S8 '164 1 .S8 1718 48
6.35 2.78 '164 2.78 2 51
Bell Type
TI Body Diameter
A f Drill Diameter
D f Bell Diameter
E f Drill Lenath
C
I Overall Lenath
L
Size
Designation Inches
11
12
'la
%6
Millimeters
3.1 8
4.76
F Inches 1 Millimeters
1.19
1.59
F Inches
0.10
0.1 5
Millimeters
2.5
3.8
Millimeters [ Inches
1.19
1.59
I Millimeters
32
48
13 'I4 6.35 2.38 0.20 5.1 2.38 51
14 51' 6 7.94 2.78 0.25 6.4 2.78 54
15 '/i 6 11.11 3.97 0.35 8.1 3.97 70
54
I O0
O through 2
0.005 0.005 0.1 3
0.20
0.1 3
0.20
0.008 0.008
Drill length (C) 11 and 12
3 through 8
13 through 18
/M I 0.4 I 0.4
diameter
Drill ID) I All sizes I 0.0030 I 0.0000 I 0.076 I 0.000
Overall length (L) All sizes 132 h 6 0.8 1.6
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Over 1'2 through 1 Over 12.70 through 25.40 0.0000 0.001 2 0.000 0.030
Over 1 through 2 Over 25.40 through 50.80 0.0000 0.001 5 0.000 0.038
Over 2 through 3% Over 50.80 throuah 88.90 0.0000 0.0020 0.000 0.051
~~~
Over V2 through 2 Over 12.70 through 50.80 0.0005 0.0030 0.01 3 0.076
Back Taper
Diameter of Drill Tolerance Per Unit of Flute Length
Inches Millimeters Inches Millimeters
From#97 through #81 From 0.15 through 0.33 None None
Over #81 through Va Over 0.33 through 3.18 0.0000t o 0.0008 0.000 to 0.020
Over 'h through Over 3.18 through 6.35 0.0002 to 0.0008 0.005to 0.020
Over V4 through V2 Over 6.35 through 12.70 0.0002 to 0.0009 0.005 to 0.022
Over 'h through 1 Over 12.70 through 25.40 0.0003 to 0.001 1 0.007 to 0.028
Over 1 through 3% Over 25.40 through 88.90 0.0004to 0.001 5 0.010 to 0.038
56
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Flute Length
Tolerance
Diameter of Drill Inches Millimeters
Inches Millimeters Plus ( + ) Minus(-) 1 Plus ( + ) I Minus ( - )
I
From#97 through #81 From 0.15 through 0.33 .4 .4
Over #81 through '/e Over 0.33 through 3.18 3.2 1.6
Over '18 through Il2 Over 3.18 through 12.70 3.2 3.2
Over 'h through 1 Over 12.70 through 25.40 6.4 3.2
Overall Length
Inches
Diameter of Drill
Millimeters
F Plus ( +1
~~
Inches
Minus ( - )
Tolerance
Plus ( +)
Millimeters
Minus (- )
From#97 through #81 From 0.15 through 0.33 '132 '132 0.8 0.8
Over #81 through l l s Over 0.33 through 3.18 'L 'h6 3.2 1.6
Over '/a through '12 Over 3.18 through 12.70 'Is 3.2 'Is 3.2
Over '12 through 1 Over 12.70 through 25.40 'lu 'Is 6.4 3.2
Over 1 through 2 Over 25.40 through 50.80 '14 '14 6.4 6.4
Over 2 through 3% Over 50.80 through 88.90 3/8 31~ 9.5 9.5
GENERAL NOTE: 95% of drills in any one lot to fall within above tolerance. --`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
ASME B94.11M-1993
Lip Height
Tolerance
Diameter of Drill Total Indicator Variation (T.I.V.1
Inches Millimeters Inches Millimeters
Fr0m1/16 through 'L 0.051From 1.59 through 3.18 0.0020
Over through 0.076Over 3.18 through 6.35 0.0030
Over V4 through Over 6.35 through 12.70 0.0040 02 0.1
Over through 1 Over 12.70 through 25.40 0.0050 27 0.1
Over 1 throuah 3% Over 25.40 through 88.90 0.0060 0.1 52
GENERAL NOTES:
(a) 95% of drills in any one lot to fall within above tolerance.
(b) Methodof measurement: Rotate the drill in a V-block against a back end stop. Measure the cutting lip height variation on
the center to the periphery of
a comparator, or with an indicator set at a location approximately 75% of the distance from
the drill.
Centrality of Web
Tolerance
Diameter of Drill Total Indicator Variation (T.l.V.1
Inches Millimeters Inches Millimeters
From1/16 through 'L From 1.59 through 3.18 0.0030 0.076
Over '/S through Over 3.18 through 6.35 0.0040 0.1 02
Over 'IS through l/z Over 6.35 through 12.70 0.0050 O. 127
Over through 1 Over 12.70 through 25.40 0.0070 0.1 78
Over 1 throuah 3% Over 25.40 through 88.90 0.01 O0 0.254
GENERAL NOTES:
(a) 95% of drills in any one lot to fall within above tolerance.
(b)Method of measurement: Rotate the drill in a close fitting bushing. Record the difference in indicator readings of the web
at the point as the drill is indexed 180 deg.
Flute Spacing
I Tolerance
Total Indicator Variation
Diameter of Drill Actual (T.I.V.) Deviation
Inches Millimeters Inches 1 Millimeters Inches 1 Millimeters
From'/ls through '/LI From
1.59 through 3.18 0.0030 0.076 0.001 5 0.038
Over through Over
3.18 through 6.35 0.0060 0.152 0.0030 0.076
Over V4 through V2 Over6.35 through 12.70 0.0100 0.254 0.0050 O.127
Over 'h through 1 Over 12.70 through 25.40 0.01 40 0.356 0.0070 O.178
Over 1 through 3% Over 25.40 through 88.90 0.0260 0.660 0.0130 0.330
GENERAL NOTES:
(a)95% of drills in any one lot to fall within above tolerance.
(b) Methodof measurement: Place the drill in a V-block against a back end stop, and rotate it against a radial finger stop. Take
an indicator reading at the leading edge of the margin on the opposite
flute. Repeat for the other fluteand note thedifference
between the two readings. The deviation in flute spacingis equal to one-half the difference between the two readings.
58
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Runout (Straightness)
Jobbers Length: For drills smaller than .O3125in., runout tolerances to be to
manufacturer's discretion. For drills ,03125 in. and larger, runout tolerances are
to be calculated per the following formula:
[ overall length
Maximum TIR= .O001316 (drill diameter)] -k
Examples
Diameter Maximum TIR
.O08
.O07
,006
.O05
.O05
GENERAL NOTES:
(a)The portion of Table 10 on pages 59 and 60 is excerpted from Table 805 in
Metal Cutting ToolHandbook, Seventh Edition, published for theUS. Cutting
of the U.S. Cutting
Tool Instituteby Industrial Press. Reproduced by permission
Tool Institute.
(b)All dimensions are in inches.
59
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Runout (Straightness)
--`,``,`,```,`,,,,`,`,,,`,```,``-`-`,,`,,`,`,,`---
Screw Machine Lengths: For drills smaller than .O400 in., runout tolerances to
be to manufacturer's discretion. For drills .O400 in. and larger, runout tolerances
are to be calculated per the following formula:
overall length
[
Maximum TIR = .O001316
(drill diameter)
i.O0368
.O07
.O06
.O05
.O05
.O05
.O05
.O04
I .O04
6 in. Aircraft Drills
RangeDiameter Maximum TIR
.o20 .0400-,0624
.0625-.1249 .O1 5
.o12 ,1250-.2499
.o1 ,2500-.3749 o
.3750-.4999 .O07
.5000 .O05
12 in. Aircraft Drills
~
GENERAL NOTES
(a) All dimensions are in inches.
(b)95% of drills in any one lot to fall within above tolerance.
(c)Method of measurement:
(1) Straight shankdrills are to bechecked with 1 in. of shank in a V-block with
measurements taken on themargins at the point. If shank length isshorter
than 1 in., use the full length of shank.
(2)Taper shank drills are to be checked with the shank in a tapered V-block
or a precision socket.
(d)Calculated values are to be rounded to the nearer thousandth of an inch.
60