Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1
Software and hardware requirements
Introduction
Specific requirements for the operating system and software configuration must be met for the
installation.
Note
WinCC is generally authorized for use in a domain or workgroup.
However, be aware that domain group policies and restrictions of the domain may hinder the
installation. If this happens, remove the computer from the domain prior to installing Microsoft
Message Queuing, Microsoft SQL Server and WinCC. Log onto the computer in question locally
with administrative rights. Then perform the installation. After successful installation, you can
enter the WinCC computer back into the domain. If the domain group policies and restrictions
of the domain do not impede the installation, the computer need not be removed from the
domain during the installation.
Be aware that domain group policies and restrictions of the domain may also hinder operation.
If you cannot avoid these restrictions, run the WinCC computer in a workgroup.
Consult with the domain administrator if needed.
Installation requirements
The following table shows the minimum software and hardware requirements that have to be
met for the installation of the "SIMATIC WinCC Basic" software package:
Hardware/software Requirement
Processor type Intel Celeron Dual Core 2.2 GHz (Ivy/Sandy Bridge)
RAM 4 GB
This document constitutes a free excerpt compiled by the user himself/herself from the documentation provided by Siemens for this product. Siemens disclaims
all liability for the completeness of this document. It shall only be used for the user's own internal purposes. It shall not be passed on to third parties. The complete
documentation can be found at:
http://support.industry.siemens.com/dokumentation/default.aspx?DocVersionId=74495465995&Language=en-US&TopicId=65924629515 4/24/2015
STEP 7 Professional V13.1
Software and hardware requirements
Hardware/software Requirement
* For additional information on the operating systems, refer to the Microsoft Windows help or
the Microsoft homepage.
Simultaneously opening multiple instances of WinCC on a configuration PC can also increase
the hardware capacity required.
Note
"Aero Glass Style" of Microsoft Windows 7
A powerful graphics card is required for "Aero Glass Style". It requires DirectX9 capabilities
and 128 MB of dedicated graphics memory.
The performance of the architecture of the graphics system can significantly influence the
performance of WinCC.
Recommended hardware
The following table shows the recommended hardware for the operation of SIMATIC WinCC.
This document constitutes a free excerpt compiled by the user himself/herself from the documentation provided by Siemens for this product. Siemens disclaims
all liability for the completeness of this document. It shall only be used for the user's own internal purposes. It shall not be passed on to third parties. The complete
documentation can be found at:
http://support.industry.siemens.com/dokumentation/default.aspx?DocVersionId=74495465995&Language=en-US&TopicId=65924629515 4/24/2015
STEP 7 Professional V13.1
Software and hardware requirements
Hardware Requirement
RAM 8 GB or more
VMware Workstation 10
The following operating systems can serve as a host operating system for these virtualization
platforms:
Windows 7 Professional/Ultimate/Enterprise (64-bit)
You can use the following guest operating systems to install "SIMATIC WinCC Basic" on the
selected virtualization platform:
Windows 7 Professional/Ultimate/Enterprise (64-bit)
Note
The same hardware requirements apply to the guest operating system as to the respective TIA
products.
The plant operator must provide sufficient system resources for the guest operating systems.
The hardware certified by the manufacturers is recommended for the use of HyperV server and ESXi.
This document constitutes a free excerpt compiled by the user himself/herself from the documentation provided by Siemens for this product. Siemens disclaims
all liability for the completeness of this document. It shall only be used for the user's own internal purposes. It shall not be passed on to third parties. The complete
documentation can be found at:
http://support.industry.siemens.com/dokumentation/default.aspx?DocVersionId=74495465995&Language=en-US&TopicId=65924629515 4/24/2015
STEP 7 Professional V13.1
Software and hardware requirements
Encryption software:
Microsoft Bitlocker
Call-up of the WinCC Information System from the WinCC editors or via the Direct Help links
In order to still call WinCC Direct Help, the following component is installed during the
installation of WinCC:
Microsoft Help Engine
You can also call the WinCC Information System in Windows 7 and Windows Server 2008 from
the Windows Start menu or from the installation folder.
To call the WinCC Information System from the WinCC editors or via the Direct Help links,
some changes have to be made to the operating system. You can find more information on
this in the section "More information for advanced users" of Microsoft Support article "917607":
This document constitutes a free excerpt compiled by the user himself/herself from the documentation provided by Siemens for this product. Siemens disclaims
all liability for the completeness of this document. It shall only be used for the user's own internal purposes. It shall not be passed on to third parties. The complete
documentation can be found at:
http://support.industry.siemens.com/dokumentation/default.aspx?DocVersionId=74495465995&Language=en-US&TopicId=65924629515 4/24/2015
STEP 7 Professional V13.1
Software and hardware requirements
You can restore the changes to the security settings made by the installation of the TIA
Portal:
"Start > All Programs > Siemens Automation > Security Controller > Restore settings".
See also
Licensing of WinCC Engineering System
This document constitutes a free excerpt compiled by the user himself/herself from the documentation provided by Siemens for this product. Siemens disclaims
all liability for the completeness of this document. It shall only be used for the user's own internal purposes. It shall not be passed on to third parties. The complete
documentation can be found at:
http://support.industry.siemens.com/dokumentation/default.aspx?DocVersionId=74495465995&Language=en-US&TopicId=65924629515 4/24/2015