Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1888
( Reaffirmed 1998 )
Indian Standard
SPECIFICATION FOR
FABRICATED PVC FITTINGS FOR
POTABLE WATER SUPPLIES
PART 11 SPECIFIC REQUIREMENTS
(
FOR 30 BENDS
First Revision )
UDC
621.643.4.062.3
[678.743.22]:636.117
0 Copyright 1989
BUREAU
MANAK
Gr2
OF
BHAVAN.
INDIAN
9
BAHADUR
NEW
DELHI
STANDARDS
SHAH
ZAFAR
MARG
110002
January 1989
Indian Standard
SPECIFICATION FOR
FABRICATE'DPVC FITTINGS~FOR
POTABLE WATER SUPPLIES
PART11
SPECIFIC
REQUIREMENTS
FOR 30 BENDS
( First Revision )
0.
FOREWORD
Specific
Specific
Specific
metallic
Part 7
adaptors
Specific
Part 8
requirements
requirements
requirements
flanges
requirements
for 60 bends
for 45 bends
for 30 bends
for lly
bends
0.4 For the purpose of deciding whether a particular requirement of this standard is complied
with, the final value, observed or calculated,
expressing the result of a test or analysi-s, shall be
rounded off in accordance with IS : 2-1960t.
The number of significant places retained in the
rounded off value should be same as that of the
specified value in this standard.
for caps
for equal tees
for flanged tail
for threaded
1. SCOPE
1.1 This standard ( Part 1 I ) lays down the requirements for manufactcre. dimensions and marking
for fabricated PVC 30bends for potable water
supplies.
shall
conform
to IS :
2.2 Manufacture
2.2.1 A typical
shown in Fig. 1.
illustration
of 30
bend
is
2. REQUIREMENTS
2.1 General material,
sizes,
*Specification
The
general requirements
methods
of test, sampling
for fabricatad
PVC fittings for potable
1 General
requirements
(first
for
and
revision ).
2.2.3
CllllS
01 SoChClCd
FIG. I
30
BENI)
Part
General
titlings for
requirements
potable
( yjrsr
OP 30 IWNDS
S17,E
(1)
63
75
90
110
125
140
I60
I80
(2)
hllNl,llM
Rt
Alin
Min
( only for
plainbcnds
in milliniclrrs.
ran
r-----0.4 MPa
( Clrss 2 )
WA1 I. 1IllWNJWl
( t)
W~~lcnlNtr Ptllcsnl~,~E
A-_----_
0.6 MPa
( Class 3 )
1.0 MZ
(Class4)
99
(3)
63
(4)
IX9
(5)
1.4
(6)
2.0
118
75
225
17
2.4
3.8
142
90
270
l-9
2.8
4.s
173
I IO
3%)
2.3
34
5.5
197
I25
375
2.7
3.9
63
220
140
420
2.9
4,4
7.0
(7)
32
252
I60
4x0
3.4
4,9
8.0
2x3
IHO
540
3.x
55
9.0
314
200
6Oa
4.2
G.2
10.0
354
22s
675
4,7
69
11.2
393
250
750
52
7.1
125
440
280
840
58
8.6
13.9
495
31s
945
05
97
156
55x
355
I 065
7-3
IO.8
17.7
628
400
I 200
8.2
12.2
198
707
450
I 350
9.3
13.7
22.4
785
500
I 500
IO.3
15.3
24-t
X80
500
990
630
I 6HO
I HYO
I Ih
130
17.2
19.2
27-t
31.3
NIWR - Minimunl
w;~ll thickness is c;~lcul:~tcJ on the basis of 90 pcrccnt OF the minimum
cc,rrcspondlng size and the prcssurc cl:~ss of pipe rounded otT IO the next higher O-I mm.
30
* 1 is c;~lcul:clcd from
x 2x H.
300
tR, r;ldius of lllc kid.
( I) ).
NOTE -The
use of the Standard Mark is governed
by the provision of the Bureau of Indian Standards
Act 1986 and the Rules and Regulations made thereunder. The Standard Mark on products covered by
an Indian Standard conveys the assurance that they
have been produced to comply with the requirements
of that standard under a well defined system of
inspection, testing and quality control which is devised
and supervised by BIS and operated by the producer.
Standard marked products are also continuously
checked by BIS for conformity to that standard as a
further safeguard. Details- of-conditions under which
alicence for the use of the Standard Mark may be
granted to manufacturers or producers may be obtained
from the Bureau of Indian Standards.
BIS has the copyright of all its publications. No part of these publications
may be reproduced
in any form without the prior permission in writting of BIS. This does not preclude the free use,
in the course of implementing the standard, of necessary details,. such as symbols and sizes, type
be addressed
to the Director
Enquiries
relating
to copyright
or grade designation.
( Publications
), BIS.
Revision of Indian Standards
Indian Standards are reviewed periodically
and revised, when hecessary and amendments, if
any, are issued from time to time. Users of, Indian Standards should ascertain that they are in
possession of the latest amendments or editron.
Amend No.
BUREAU
OF INDIAN
Text Affected
STANDARDS
Headquarters:
Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002
Telephones : 331 01 31, 331 13 75
Regional
Telegrams
( Common
: Manaksanstha
to all Offices )
Offices :
Telephone
Central
: Manak
Bhavan, 9 Bahadur
NEW DELHI 110002
Eastern
: l/14 C. I. T. Scheme
CALCUTTA
331 01 31
331
13 75
I
37 84 99,
I 37 86 26,
37 85 61,
37 85 62
160036
53 38 43,
53
23 84
I
53 16 40,
600113
41 24 42,
E41 23 15,
41 25 19,
41 29 16
~632 92 95,
I 632 78 92
63 27 80,
700054
Northern
35-C, CHANDIGARH
Southern
Western
: Manakalaya,
Branches
: AHMADABAD,
( East )
BANGALORE,
BHOPAL, BHUBANESHWAR,
COIMBATORE,
FARIDABAD,
GHAZIABAD, GUWAHATI,
HYDERABAD,
JAIPUR,
KANPUR,
LUCKNOW, PATNA, THIRUVANANTHAPURAM.