Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Steam
conditioning
valve ready
for shipment
to one of the
paper plants.
PRODUCT RANGE:
Testing of
Bypass valve
being carried out at
our works by our
collaborators from
Germany
High pressure
PRDS valve ready
for shipment to
Reliance Jamnagar
Refinery alongwith
spray water control
valves.
DESUPERHEATERS
PRESSURE REDUCING AND DESUPERHEATING VALVE
(STEAM CONDITIONING VALVE)
The principle function of any
that the size of the water droplets
desuperheater is to accelerate
should be smallest, utmost
the phenomena of absorption of
surface area available,
the spray water by the steam so
absorption will be almost
that steady conditions of steam
instantaneous and true
temperature are reached within
temperature will be measured
a short distance from the outlet
within the shortest distance.
at all loads. This ensures that
poor quality of steam or water
In all instances of desuperheating,
droplets are not carried
the nature of the downstream
downstream in the steam
steam and the avoidance of large
pipeline. The purpose therefore,
spray water droplets that can be
is to develop methods by which
propelled at high speed to
heat transfer between steam and
damage elbows, valve seats, heat
water can be hastened. The
exchanger tubes, or process
main purpose is to break spray
material are very important factors
water droplets into very fine
while designing desuperheating
particles at all loads to ensure
system and equipment selection.
increased surface area for water
to come in contact with the
Cross section
of Steam
steam is
conditioning valve
available,
thereby
increasing
Steam
the rate of
conditioning
valve ready
evaporation.
for shipment
It
is very clear
to one of the
paper plants.
STEAM CONDITIONING
VALVE SC
Leslie series `SC' steam
conditioning valve with revolutionary
multinozzle atomizer and feed
forward design adds to our latest
generation of quality valves. The
equipment is utilized for
simultaneous pressure and
temperature reduction of steam.
The cooling water is introduced in
the highest turbulent zone of the
steam. High steam velocity at this
point, results in the highest
coefficient of heat transfer between
the steam and water. The feed
forward design assures soft misty
spray and instantaneous
temperature control over the full
range of steam flow.
Cut section of
Steam conditioning valve
Sizes
Rangeability
Rating
Superior Water pressure
:
:
:
:
MARK - I
Mounting
arrangement
Sizes
Rangeability
Rating
Superior Water Pressure
Actuator
Flow characteristics
: Mounting of the
desuperheater in the
steam piping of size 6"
onward (regardless of pipe
size) is always 4" and 1"(or 2")
for water inlet.
: 350:1 can be accommodated.
: up to ANSI 2500#.
: 5 bar above the line pressure OR
high pressure BFW.
: Leslie R50 positioning cylinder.
: Modified, Equal %, Linear
Lancer Multinozzle
Desuperheater
Internals
Detailed
view of
nozzle
arrangement
in assembled
condition
evaporates almost
instantaneously avoiding pipe
impingement and eliminates the
need of separate coolant valve.
Reliability is at its maximum
owing to hard faced trim and
single moving part. It utilizes full
pressure drop at all conditions
thereby maintaining its
Mounting arrangement
Sizes
Rangeability
Rating
Superior Water Pressure
Cross sectional view
10
Actuator
Flow chracteristics
Sizes
Rangeability
Rating
Superior Water pressure
:
:
:
:
2 to 30
6 : 1 for single venturi type and 12 : 1 for double venturi.
upto ANSI 2500#
Cooling water can be fed at steam operating pressure.
11
Cross section
of In-line Venturi
12
Cross section
of Mini Venturi
HP Bypass valve
awaiting shipment
Seat/cage assembly
Plug/cone assembly
13
14
15
16
173
18
DUMP TUBES
DUMP TUBE
19
DUMP TUBE
Fig.2
Dump tube installation for Air cooled Condenser.
2 20
construction is normally
carbon steel with 17% Cr
plasma nitrided trim ensures
smooth, trouble-free and
everlasting performance.
A typical application would be
to reduce water pressure
from 120 Bar down to 1 Bar.
Leslie ARC valves can be
found in Nuclear power
plants in India that served as
an import substitute, thereby
saving valuable foreign
Sizes
Rangeability
Rating
Characteristics
Actuator
:
:
:
:
:
1/2 to 6
30 : 1
upto ANSI 2500#
ON/OFF, Equal % Linear, Modified
Leslie R50 positioning cylinder.
21
l
l
l
Cut section
Pressure reducing
valve awaiting
shipment
Detailed view of
Pressure reducing valve
Sizes
Cv
End connections
Temperature Limit
Pressure Limit
22
:
:
:
:
1/2 to 4
0.05 to 105
Screwed or flanged up to 600 # rating
Upto 270oc with stainless steel spring
and 410oc with Inconel spring
: 46 bar
VARIATIONS
Soft Seat Arrangement
In order to avoid seat leakage
on light gas services, the main
valve/seat and pilot valve/seat
are provided with elastomer
seat seals. The elastomer
material are selected to suit the
duty conditions. Another
important application for this
type of valve, is an explosive
nature of gases, e.g. Hydrogen.
When the gas passes through
the valve at high velocity, static
charges are created leading to
the possibility of spark, this can
be disastrous in explosive gas
atmosphere. Under these
circumstances, the soft seated
valve is always recommended.
Auxiliary Valve
Reduced Capacity Trim
- In cases where it is more
convenient, on account of the
pipe connection, to have a
valve larger than is necessary
to deal with the quantity of
steam, we can fit smaller
seats so that regulation will be
satisfactory.
Cage Guided Trim
In order to obtain high pressure
drop, normally two or more
valves are installed, which is
expensive and often
disappointing, when the leakage
of the upstream valve throws all
the /\ P on the downstream
valve. In such cases, a PRV
with multijet caging is
recommended. The three stage
pressure reduction (number of
stages are decided based on
critical /\ P ratio) is achieved
with the help of multistage
perforated cage. The design
offers the following advantages :
- Flow distribution leads
to the noise attenuation.
- Pressure drop is distributed
across different stages and
not at the throttling point
between main valve and seat,
thus reducing the trim wear.
- Low cost installation and
Large turndown
achieved by twin
plug arrangement
23
REFORMER VALVE
STEAM REFORMER BY LESLIE TO IMPROVE
PLANT PERFORMANCE AND PRODUCT QUALITY
24
1)
2)
3)
4)
5)
Reformer Valve
Pressure Reducing Valve
Isolating Valve
Bypass Valve
Safety Valve
3
Pressure reducing station incorporating Reformer unit makes
it extremely compact, cost efficient and easy to maintain.
25
Packing:
Regular packing material are
PTFE & Graphite Asbestos.
However, for most applications
like steam and other hazardous
fluids, Grafoil (pure graphite) is
recommended by Leslie.
Grafoil contains no
resins/binders or fillers and
offers outstanding high
temperature characteristics.
Actuators:
Our experience shows that the
control valve with pneumatic
piston cylinder actuator gives
the best performance. This
control valve with valve
positioner has a very high
frequency response and
positioning accuracy. However,
if required we can supply control
valves with spring and
diaphragm actuator.
Body forging and trim
material incorporated in
high pressure Control valves
Type
Type
Material
27
Type
28
Type
Material
: Three-way
: Carbon Steel, Stainless Steel
or Other Alloys.
Sizes
: 1 through 6
End Connections : Flanged
Ratings
: 150# through 600#
Actuator
: Leslie positioning piston
cylinder or spring and
diaphragm
2 nos 16 size Control valves ready for shipment to
Pan Africa Paper mills. Supplied to Triveni, Banglore for
their export order.
29
SL 1000 B
Cut section of
conventional
spring loaded
Safety valve
Pilot - Operated
Safety Relief Valves
Leslie pilot-operated safety
Relief Valve is an autonomous
valve. It does not need any
auxiliary source of power to
operate. The fluid under
pressure in the equipment to be
protected is used to actuate all
operational modes.
Pilot operated
Safety valve
Safety valve
incorporating
Bellows
SL 1000
SL 5000
set pressure
Low Pressure
Safety Relief Valves
Designed for Low Pressure [100
mm water column to
1Kg/cm2(g) relief. Valve is pilot
operated for instant pressure
relief at set point. Soft-seated
for bubble-tight seal when valve
is closed.
SL 5000 LP
SL 1000 E
SL 6000
Lever & weight
Safety valve for
large flow
applications &
low pressures.
on valve size.
Lever and Weight
Safety Valves
31
PNEUMATIC ACTUATORS
Actuator
incorporating 8
Stroke length
l
l
l
l
l
Fast Response
High Power
Low Hysterisis
Cycle tested and guaranteed for multi-million operations
Designed for working on corrosive atmospheres
Size
Stroke
Stroking Time
Thrust
Linearity
Hysterisis
32
:
:
:
:
:
:
33
QC department
LESLIE capabilities
Assembly shop
35
www.lesliecontrols.com
sales@lesliecontrols.com
800.439.4485
Member of the
U.S. Green Building Council
10/0.1.102010.3