Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
TA - 11 - Ed 11 - September 2014
PUMP
IDENTIFICATION
(Not all model combinations are available
Consult your Suntec representative)
APPLICATIONS
- Light oil, B10 heating oil/biofuel blend (as defined in DIN V51603-6) and
kerosene.
- One or two-pipe system.
TA : Pressure regulation
Shaft rotation
(seen from shaft end)
A : clockwise rotation
C : anti clockwise rotation
TA
40 10
Pressure range :
30 : 7 - 30 bars
40 : 7 - 40 bars
PREHEATING FACILITY
Care should be taken to avoid starting pump with high viscosity cold oil leading to
pump and coupling damage. For this reason, the TA pump body includes a cavity
to accept an electric preheater. This cavity has been located to give maximum heat
transfer from the heater to the oil in the pump without direct contact between the
heater cartridge and the oil.
Heaters should be connected for a period of time prior to starting the pump. When
the right temperature is reached, they can be switched off or left permanently
switched on to maintain fluid oil in the pump during the periodic burner shut-downs.
The oil supply, pipes and filters must be separately heated.
Preheater facility
Revision number
Vacuum or
inlet pressure
gauge port
Vacuum or
inlet pressure
gauge port
Pressure
gauge port
Intake
from Tank
To
nozzle
By-pass
plug
inserted
Pressure
gauge port
Intake
from Tank
To
nozzle
By-pass
plug
removed
Pressure
adjustment
Pressure
adjustment
Return
TWO PIPE
INSTALLATION
ONE PIPE
INSTALLATION
Return
plugged
SUNTEC INDUSTRIES FRANCE - 1, rue Lavoisier - CS 60102 - F-21603 LONGVIC Cedex - Tel. 33 (0)3 80 70 60 70 - Fax 33 (0)3 80 70 61 11- www.suntec.fr
Pump capacity
TECHNICAL DATA
Mounting
Flange mounting
Connection threads
Inlet and return
Nozzle outlet
Pressure gauge port
Vacuum gauge port
Shaft
12 mm
By-pass plug
Weight
Hydraulic data
Oil temperature
2400
Inlet pressure
light oil :
2200
heavy oil :
light oil :
heavy oil :
5 bars max.
5 bars max.
1600
Torque (@ 40 rpm)
0,3 N.m
15
20
25
75 cSt
20 cSt
5 cSt -
30
35
40
45
Pressure (bars)
Data shown are for new pumps, with no allowance for wear.
Power (W)
Rated speed
10
Viscosity =
Operating viscosity
2 - 75 mm/s (cSt)
(Higher viscosity oil can be used by feeding the pump
and by heating the oil to lower its viscosity under 75 cSt.
For kerosene applications, contact SUNTEC)
Return pressure
Capacity (L/h)
1600
1500
1400 TA5
1300
1200
1100
TA4
1000
900
800 TA3
700
600
500 TA2
400
300
200
100
0
General
Power consumption
2600
2000
1800
TA5
1400
TA5
TA4
TA3
TA2
1200
1000
800
600
Choice of heater
TA4
TA3
TA2
400
200
Cartridge
12 mm
Fitting
according to EN 50262
Rating
80-100 W
0
0
10
15
20
25
30
35
40
45
Pressure (bars)
Viscosity =
75 cSt
5 cSt -
Data shown are for new pumps, with no allowance for wear.
PUMP DIMENSIONS
50
54
58
125
66
64
101
36
22,5
22,5
n
B
54
130
11
19 min
M16x1,5
85
4
12
13,5
B-B
36
n Suction
o Nozzle outlet
102
1,5 max
8 min
12 min
Return
Pressure
gauge port
12,1 min
66
11
71,5 min
Pressure
adjustment
t Preheater
cavity
TA - 11 - Ed 11 - Sept. 2014