Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Release 4.5.1
278700 Rev. A.14
1-i
Refer to this publication for complete and accurate information that helps you better operate and service Metso
Automation equipment. Your comments and suggestions are welcome.
Metso Automation
1180 Church Road
Lansdale, PA 19446
Attention: Manager, Technical Publications
1-ii
Contents
CHAPTER 1.........................................................................................................................
Introduction...................................................................................................................................................................
Overview.....................................................................................................................................................................
Release Compatibility.........................................................................................................................................
Windows XP.......................................................................................................................................................
Release 4.5.1 Updates Details................................................................................................................................
Display Changes in Support of Redundant MIO...............................................................................................
maxSCRIPT Additions in Support data quality propagation.............................................................................
maxDPUTools Changes in Support of MIO.....................................................................................................
maxDPUTools Custom Blocks Changes...........................................................................................................
Atom Compiler Improvements.........................................................................................................................
maxDPUTools Find and Replace Improvements.............................................................................................
maxDPUTools Bookmark Navigation Improvements......................................................................................
OPCGateway Client Improvements.................................................................................................................
Release 4.5 Updates Details.................................................................................................................................
Display Changes in Support of MIO................................................................................................................
System Menu Display Changes........................................................................................................................
DPU4FStatus Display Changes........................................................................................................................
maxDPUTools Changes in Support of MIO.....................................................................................................
maxDPUTools I/O Cross Reference Summary.................................................................................................
OPC A&E Client..............................................................................................................................................
Release 4.4.1 Updates Details..............................................................................................................................
DPUBusMap Display Changes.........................................................................................................................
maxVUE mcsButtonControl.............................................................................................................................
maxVUE Editor................................................................................................................................................
Release 4.4 Updates Details.................................................................................................................................
maxSTATION File Synchronization................................................................................................................
maxSTORIAN Version 2...............................................................................................................................
maxARCHIVER Version 2............................................................................................................................
HealthLog Alarm Severity................................................................................................................................
Event Collector...............................................................................................................................................32
Virtual DPU Subscription Parameters............................................................................................................33
Additional DMT Alarms................................................................................................................................34
Sizeable Trend Wrapper..................................................................................................................................35
OPC Server Enhancements............................................................................................................................36
maxDPUTools Enhancements........................................................................................................................37
Network Diagnostic Enhancements...............................................................................................................38
HART 16 channel AI Module.........................................................................................................................39
maxVUE Editor Enhancements.....................................................................................................................40
Release 4.3.1 Updates Details............................................................................................................................41
maxDPUTools Download Events...................................................................................................................42
OPC Gateway Improvements.........................................................................................................................43
MaxVUE Event Summary Filtering Improvements......................................................................................44
ModbusSlave Library......................................................................................................................................45
Release 4.3 Updates Details...............................................................................................................................46
TC Linearization............................................................................................................................................47
105-2
Introduction
Enabling Non-Uniform Automatic Daylight Savings..................................................................................106
maxDPUTOOLS Incremental Download Improvements............................................................................107
Release 4.0.3 Updates Details..........................................................................................................................108
Improved Support for Propagation of Local alarms..................................................................................109
Updated Health Log Status Display.............................................................................................................110
Updated DPU4E I/O Status Display.............................................................................................................111
Release 4.0.5 Updates Details...........................................................................................................................112
Default Report Printer..................................................................................................................................113
maxSTORIAN new Registry entries.........................................................................................................114
DPU4F...........................................................................................................................................................115
CHAPTER 2.....................................................................................................................116
Bugs Fixed..................................................................................................................................................................117
CHAPTER 3...................................................................................................................118
Special Instructions for Upgrades.........................................................................................................................119
Overview...............................................................................................................................................................120
Border scheme corruption Release 4.5.1.......................................................................................................121
System Menu Display Release 4.0.5.............................................................................................................122
DPU Bus Map Display Release 4.4.1............................................................................................................123
124-3
Chapter 1
Introduction
Overview
Release 4.5.1 is a minor upgrade from Release 4.5 with respect to
general WorkStation software. However, Release 4.5.1 adds support for
Metso redundant MIO Modules present in the new 5.1 ACN Release,
using the new EIBC buffer (9/38 build version and later). Please refer to
the Release 4.5.1 Release Updates Details section below.
Release 4.5 introduces support for maxACN and metsoDNA IO (MIO)
to the WorkStation.
The maxACN is an alternate processor for
maxDPU4F. The maxACN is designed to go in hand with MIO an
alternate I/O structure to the maxDNA maxPAC product. If you do not
have either the maxACN or MIO you are probably not interested with
this release.
Release 4.5 removes all DPU/ACN setup files from this
maxSTATION installation disk. It also removes the Virtual DPU files
from the installation disk. You must install all DPU/ACN files
including the Virtual DPU from the maxDPU4F installation disk. If
you are upgrading from a previous release, any existing files will not
be removed by the maxSTATION installation.
Release 4.4 introduced the new features:
Version 2 of maxSTORIAN
With Release 4.4 and later, you must choose between Classic
maxSTORIAN and Version 2 maxSTORIAN during the installation
process.
Release 4.3 introduced a two-CD installation pack. The Pre-requisites
CD must be installed first. It is typically installed only once. Then the
Installation CD may be installed. The maxDNA Setup Helper utility will
guide the installer in correct CD installation.
Release 4.3.1 removes the DPU4F setup files from this maxSTATION
installation disk. In order to get the latest DPU4F files, you must
install them from the latest maxDPU4F installation disk. If you are
Release Compatibility
Release 4.x has many enhancements to various subsystems. Several
enhancements require some action on the part of the user before the 4.x
Release is installed:
Existing Virtual DPU MXT files will be incompatible with the new
virtual DPU. The existing database should be uploaded using the
maxDPUTools utility before the upgrade, then downloaded and a
new MXT file created after the upgrade to Release 4.4.
Release 4.x of maxDNA will work with previous DPU4E/F releases
going back to 2.1. This permits a system to be upgraded first by
upgrading the maxSTATIONs, followed by the DPU4E/Fs at a later date
when the system can either be shut down or placed in a fail-safe mode.
Release 4.4 does not include any DPU4E/F releases. For the most up-todate versions of the DPUs, refer to the Metso Automation Web site or the
latest version of the maxDPU4E/F Release media.
It should be noted that Release 2.x, 3.x maxSTATIONs and Release 4.x
maxSTATIONs are compatible with each other for daytoday
interaction. Subscriptions made from stations of any software revision to
those of the other revision will be successful. This will allow a gradual
transition to Version 4.
maxSTATION configuration tools (maxDPUTOOLS, maxVUE Editor)
are upward compatible only. Release 4.x displays cannot be used on a
Release 2.x station.
Note that there are special considerations for upgrade of Version 1.x
workstations. See Metso Customer Care.
Note that there are special considerations for support of IEC1131 as
applied to maxDPU4B. See Metso Customer Care.
1-2
Windows XP
Release 4.x runs only in a computer running Microsoft Windows XP.
Windows XP offers longer-term support than Microsoft Windows NT 4.0
or 2000 has; Windows XP offers a more-modern interface to the user;
and supports more hardware, such as USB ports.
As a result of the use of Windows XP, the maxSTATION now requires at
least 256MB of memory, due to the larger memory footprint occupied
by the operating system. While Version 4.x performs equivalently to
Version 3 (given the increased RAM), it may be time to consider a
processor upgrade at the same time to take advantage of the performance
of modern technology.
It is our recommendation that the workstation disk be reformatted to
install Windows XP (vs. an upgrade from Windows NT 4.0 or Windows
2000). Our experience is that this leads to the least problems upgrading
the operating system and the best long-term reliability.
Update details for all Release 4 versions are included below.
2-3
1-4
2-5
1-6
include events into the event history. Refer to the updated 278615 OPC
Users Guide that is part of the online release manuals.
maxVUE mcsButtonControl
The capability was added to display a confirmation message before doing the
button writes. This was implemented by adding a new attribute on the
LiveData Property Window in the form of an edit box (see figure below). If
the box is blank, no write confirmation will occur. The syntax of the text
includes adding a custom text to the caption bar of the confirmation message
that is displayed. Only one confirmation is required for all the writes
configured for the button. Parameter expansion and alternate language
conversion are applied to the text.
2-7
1-8
If you specify Option Switches here, they will be used instead of any
value entered in DpuList.ini.
Event Collector
The Event Collector has been enhanced to preface the tagname for LSS
events from stations other than its own with the originating station name
similar to the Alarm Summary presentation of foreign LSS alarms.
2-9
1-10
2-11
File Browsing
The interface that selects a starting location for file browsing has
changed:
Action
Browse for Toolbar associated with a
display of type Main
Browse for New MN
Browse for Display Navigation property
Save or Copy Sheet MN
Open MN
Insert MNG
Save MNG
Insert BMP/WMF
Save SAMA MNG
Initial Location
C:\Custom\Displays\Operating
C:\Custom\Displays\Operating
C:\Custom\Displays\Operating
C:\Custom\Configs\Operating
Check the Most Recently Used file list and start in the most
recent folder. If no list has been created, start in
C:\Custom\Displays\Operating.
If the most recently used file was a Configuration Sheet,
start in C:\Custom\Displays\Operating.
C:\Custom\Displays\Operating\Common\MNG
C:\Custom\Displays\Operating\Common\MNG
C:\Custom\Displays\Operating\Common\BMP
C:\Custom\Configs\Operating\Common\MNG
Items have been added to the right click menu in support of maxVUE
Editor enhancements.
2-13
A line may be
Note that in order to use a non-solid line, the line thickness must be either
1 Pixel or Single at any Zoom.
As shown above:
Operator action (OA) type events are generated.
1-14
2-15
The Async and OnDemand options have been moved to the group
level.
1-16
2-17
1-18
The sizeable Trend Wrapper provides an interface that allows the user to
save the current trend settings as a Bookmark. This bookmark can be
used to mark an event such as an upset. The user can move from trend to
trend without the need to relocate the point in time where the upset
occurred. Please refer to Manual 278599, the maxSTATION Operators
Guide for more information.
Multiple-Sheet Printing
The Graphical Configurator has been updated to include a Print
Configuration Sheets File menu item that allows the user to print
multiple Sheets with one print request. Please refer to Manual 278606,
the Graphical Configurator Users Guide for more information.
maxVUE Tiling
The ability to tile displays in maxVUE Runtime has been added. Use of
the tiling option is controlled by Soft Key authorization. When maxVUE
is launched, it starts up to four additional maxVUE processes that
include a Windows title bar, allowing for re-sizing, minimizing, dragging,
etc. Please refer to the 278599 maxSTATION Operators Guide for
more details.
maxVUE text alignment properties
The List Control and Text State Control have been updated to allow the
user to configure text alignment. Any value displayed by these controls
may be specified as left, center, or right aligned. The alignment defaults
to Auto to keep the behavior consistent with older versions: numbers
are right aligned and text is left aligned.
maxVUE Snapshot files
A new folder has been created for files that used by the maxVUE
Runtime Snapshot/Restore functions. The files are placed and retrieved
in the folder C:\Custom\Snapshot\<PC Name> (where <PC Name> is
the name of the maxSTATION).
maxVUE Border Scheme Property
The ability to dynamically enable/disable the Border Scheme property of
a maxVUE object has been added. Use the maxSCRIPT CtlOut
interface
(e.g.
Dim
listBorder
as
IntCtlOut
(ListBox.UseBorderScheme) to enable or disable the property for
a maxVUE object. A value of 1 will enable the property and a value of 0
will disable the property. The object must be stored and configured with
the property enabled.
Alarms Out of Service Display
A new Point Summary display to show Alarms Out of Service has been
added. Please refer to the Operator Users Guide (278599) for more
details.
2-19
1-20
Refresh Tree refreshes the tree view. Search simplifies searching the tags
by refining the tag list as you enter letters corresponding to the beginning
of the tag. You must be in the Tagnames tree to use this feature.
maxVUE Editor Toolbars
Toolbars in maxVUE Editor now retain their positioning and visibility
between instances. The first time the program is opened, the toolbars
will appear in their default positions, subsequent uses will restore the
toolbars to their last state.
This information is retained after
maxSTATION and workstation shutdown. Toolbars can be enabled or
disabled using a new option in the view menu, Toolbars, which lists the
toolbars (toolbars that are invalid in the current mode are grayed).
DPU4F Detail Displays IRIG Indicators
A change was made to the IRIG status annunciators on the DPU4F
Details and DPU4F Pair Details displays. In previous releases, the
annunciator on the inactive DPU would show IRIG Failure because the
inactive DPU does not decode the IRIG signal. That was misleading in
that there really was no failure. So, in release 4.3, the annunciator on the
inactive DPU will be blank. The annunciator on the active DPU will
continue to show the current IRIG status (IRIG OK or IRIG
Faikure). The annunciators on both DPUs will also continue to show
IRIG is not enabled when that condition exists while the DPU is
configured to be a Time Master.
Modbus, AllenBradley Libraries
Three new standard libraries can be imported into a DPU4F
configuration in maxDPUTOOLS to create serial links to PLC devices.
The libraries contain custom blocks that build protocol specific messages
that can be transmitted by a Serial Communication Module (SCM) I/O
card. The libraries are Modbus (master), AllenBradley and SCM. The
SCM library contains common functions that would be used by either
protocol. See the DPU4F Links Configuration Guide (278718) for
detailed information.
2-21
1-22
Note that the previous dialog is for release 4.3 and later configuration
versions. For Earlier versions, only the Expert option is allowed,
presented as a check box, and the dialog has the following presention:
2-23
1-24
2-25
1-26
Documentation Updates
1. Numerous updates have been made to the documentation that is
included as part of the release as PDF files (in the folders below
C:\Mcs\maxDOCS\_Release 4.2 Manuals).
2. The PDF manuals have been modified to allow the user to add
comments.
USB Dongle
1. Replaces the slower parallel dongle.
2. Provides a faster interface to programs that check for dongle
presence. Usable on laptops that do not have a parallel port.
3. USB dongle is only supported in version 4.2 and beyond. Parallel
dongle is supported in all versions without hyper-threading/dual
core.
4. A USB dongle is required for stations with hyper-threading or dual
core.
2-27
1-28
Limits by station limits the number of subscriptions from any single station
to the DPU.
There are also a few restrictions on outgoing traffic:
Limit to number of outgoing references a restriction on the total traffic (peerpeer) that can be generated by a single DPU
Limit to number of unoptimized subscriptions a logical connection between
internal objects in a DPU that take work each time the block is executed. In
an optimized subscription, the destination object directly accesses the source of
data. An unoptimized subscription is access to data that is not stored, but that
must be computed each time it is accessed.
All limits can be set in maxTOOLS using object \system\SBPLimit. There are
usable defaults for each parameter. There is a new master database for
maxTOOLS that is required for editing limits (alarms) and hard limits.
However, it is strongly recommended that the user not change the default hard
limits. The default hard limits permit a high level of system functionality
without overburdening the DPU with subscriptions. Increasing the hard limits
risks causing DPU problems. Only increase a default hard limit as a last
resort. It is far better to go to the sources of the subscriptions and reduce their
need for them than to raise the limits and put more burden on the DPU.
In addition to providing limits and alarms, the SBP Limiter atom also provides
statistics to indicate who the top (highest) users of subscriptions to the DPU
are. This information is useful because knowing who is using the most
subscriptions is the first step in reducing the number of subscriptions.
The SBPLimit atom's configurable parameters are:
HiLimTotalSub
HardLimTotalSub
HiLimStnSub
HardLimStnSub
Default Value 4000 - No station should consume more than half the
capacity of the DPU.
Specifies the Hard limit value for subscriptions from any particular
station (DPU or maxSTATION). Above this level any new subscription
from that station will be rejected.
Default Value 5000 - No station should consume more than half the
capacity of the DPU
2-29
HardLimConnLoop
HiLimConnNorm
HardLimConnNorm
HiLimConnBgnd
HardLimConnBgnd
HiLimOutRef
HardLimOutRef
HiLimUnOptRef
HardLimUnOptRef
Specifies the High Alarm value for subscriptions from any particular
SBP connection running at Loop Priority.
Default Value 180 - Loop Subscriptions are used for DPU to DPU
communications. The number is small since they are handled at 1/4
second resolution.
Specifies the Hard limit value for subscriptions from any particular SBP
connection running at Loop Priority. Above this level any new
subscription from that station will be rejected.
Default Value 200 - Loop Subscriptions are used for DPU to DPU
communications. The number is small since they are handled at 1/4
second resolution.
Specifies the High Alarm value for subscriptions from any particular
SBP connection running at Normal Priority.
Default Value 1500 - Normal Subscriptions are primarily used for
maxVUE and browser communication.
Specifies the Hard limit value for subscriptions from any particular SBP
connection running at Normal Priority. Above this level any new
subscription from that connection will be rejected.
Default Value 2000 - Normal Subscriptions are primarily used for
maxVUE and browser communication. 2000 values from a single DPU
should be considered extreme.
Specifies the High Alarm value for subscriptions from any particular
SBP connection running at Background Priority.
Default Value 2000 - Background Subscriptions are primarily used by
maxSTORIAN communication.
Specifies the Hard limit value for subscriptions from any particular SBP
connection running at Background Priority. Above this level any new
subscription from that connection will be rejected.
Default Value 3000 - Background Subscriptions are primarily used by
maxSTORIAN communication. 3000 values from a single DPU exceed
the possible real point count by more than a factor of 2.
Specifies the High Alarm value for External References. (Those
containing a '[')
Default Value 450 - 1/4 second data may lag significantly if external
references exceed this value.
Specifies the Hard limit value for External References. (Those
containing a '[') Above this level any new outgoing requests will be set
to BAD_REF quality and not processed.
Default Value 500 - Values above 500 are not recommended in fully
loaded DPUs.
Specifies the High Alarm value for Internal Unoptimized References.
Default Value 720 - 1/4 second data may lag significantly if
unoptimized references exceed this value.
Specifies the Hard limit value for Internal Unoptimized References.
Above this level any new internal unoptimized reference requests will
be set to BAD_REF quality and not processed.
Default Value 800 - 1/4 second data may lag significantly if external
references exceed this value.
1-30
The DPU will annunciate alarms for exceeding any of the above limits. The
format of these alarms is:
UnOpt Ref High %#22%
2-31
Names
Names
Names
Names
Note: Only Top station statistics are visible unless expert mode is turned on in
the browser. Name and connect Ids are of the form NAME:##.
HART
1. New HART enabled maxPAC analog input module IOP 307 please
refer to the maxPAC Hardware Reference Guide (278596)
2. FieldCare integration with HART enabled maxPAC I/O modules.
Trending improvements
1. A new stretchable, mult-instance trend wrapper. See manual 278599
for additional information.
1-32
2. In addition to the resizing, this grid outlines the tagname field when it
is the selected point.
Note: the new grid does not use the configured Font point size, but sizes
text to fit the number of rows in the grid. It may be necessary to change
the number of rows (or control height) in the Alarm List/Summary to
achieve the same Font point size as before this change.
2-33
maxDPU4F
1. New form includes a faster (300Mhz) processor and more memory.
2. Complete identity is contained on compact flash. The compact flash
contains executables for the bios, CP, IOM, FPGAs and the dpu
database saved in mxt form. Software upgrades are accomplished
simply by plugging in a new compact flash. The DPU4F will
automatically load the new images. The compact flash can be
upgraded when plugged into a media writer at the workstation or
over the network when plugged into a DPU4F.
3. Critical time class has been improved from 20 milliseconds to a 10
millisecond maximum. The default is still 40.
4. Improved network security. DPU4F will only accept network
messages from an approved station. Network messages are filtered
at the ethernet driver level reducing the load on upper level
programs.
5. DPU4F does not use batteries. No longer a maintenance issue.
6. DPU4F does not need a processor cooling fan.
1-34
it
operates
2-35
2-37
In the above example the sections labeled Ethernet Cable Breaks and
Alarms and Status at the top of the display have been added. As shown
no cable breaks are present as indicated by Good status for each list
entry as a Yellow Smile icon and as text in the Transaction status column
(labeled TransStat). Within the Ethernet Cable Breaks section, the two
icons representing the A and B network status are shown with a
green background color, and cable break counts of zero appearing below
1-38
the icon. Within the Alarms and Status section, the checkboxes
indicating a Cable Break (labeled CabBreak) and No Communication
(labeled NoComm) are both clear, and the Alarm Text box indicates
Cleared. Note these statuses are accessible on the SBP as attributes
CabBreak, NoComm, and Alarm_Text of the service named
_HealthLog.
Below is the next pictorial example with a cable break present:
2-39
1-40
DPU4F
1. The DPU has been corrected to reject duplicat HID and/or Relative
IDX entries in a configuration during download. A configuration with
duplicate HID texts, which would previously have downloaded, will
now fail during the Commit phase (see below).
2. The maxDPUTools utility should be used to detect and correct these
duplicates and the DPU re-downloaded. Use the File Duplicate
Names menu item. Note that the problem HID is also shown in the
maxDPUTools error log.
2-41
1-42
Chapter 2
Bugs Fixed
The following bugs have been fixed in either this release or its most recent predecessors.
Fixed
4.0
Subsystem
DPU4F
4.0
maxVUE
4.0
Events
4.0
maxVUE
4.0
4.0
4.0
4.0
maxVUE
maxSTORIAN
maxVUE
maxLINKS
4.0
4.0
DPU4F
Software Backplane
4.0
Software Backplane
4.0
4.0.1
4.0.1
4.0.1
4.0.1
4.0.1
4.0.2
maxVUE
maxVUE, DPU4F
DPU4F
DPU4F
maxVUE
maxVUE
maxVUE
4.0.2
maxVUE
Description / Explanation
Fixed the problem when too many macros are assigned in one
group (only a browser interface problem). Fixed the "Data
Error" problem when too many unoptimized text reference
subscriptions are assigned.
Need to prefix DpuName on Tagged Objects when selecting
them in the Graphical Configurator.
Fixed crash after 500 events. Close timing window with server
when creating a new mdb.
Increase limit of display on Healthlog from 100 to 300 entries.
Prevent crash when limit exceeded.
Modifications for Daylight Savings.
Fixed Crash on Yield. A number of other miscellaneous fixes.
Crystal report formats updated for spacing problems.
Changes to the overrun detection code. Changed Alarm
handling to avoid continuous alarm posting. Also the alarm
severity is configurable via sbp. Added code for a new
member ALM_SEVERITY. Changes to the interface structure
used for alarms.
Added Defeat attribute to all buffers.
Fixed a retry mechanism to get more timely re-subcribes on a
failover.
Fixed the occasional inability to get data and lost
subscriptions in the proxy server.
Fixed the trend wrapper Copy to File function.
Added a third alarm sort. (ack/sev/time, sev/time, ack/time)
Allow an additional 100 macro definitions.
Dpu will reject a duplicate tagname (within itself).
Supports Transfer Points
MCSDpuStatus control - Correct secondary CP light coloring.
maxScript Control: Add ability to read properties of other
maxVUE controls.
#214 - Shift Report Format error with DST
#1984 - DST vs. Daily Shift Report
Multiple changes to support daylight savings time.
TimeZone.ini is a new file in C:\custom\Sbp that may have to
be edited. See the ini file for detailed instructions.
Subsystem
maxVUE
4.0.2
4.0.2
maxVUE
maxSTATION
4.0.2
4.0.2
maxSTATION
maxVue
4.0.2
4.0.2
4.0.2
maxDPUTOOLS
maxVUE
DPU4F
4.0.2
maxSTATION
4.0.2
DPU4F
4.0.2
4.0.2
4.0.2
DBM
maxSTATION
maxDPUTOOLS
4.0.2
DPU4F
4.0.2
4.0.2
4.0.2
4.0.2
4.0.2
4.0.2
4.0.2
maxDNA
maxVUE
maxVUE
maxDPUTOOLS
maxSTORIAN
maxSTATION
maxSTORIAN
4.0.2
4.0.2
4.0.2
maxDPUTOOLS
OPC Server
DPU4F
4.0.2
maxVUE
4.0.2
4.0.2
maxDPUTOOLS
maxSTORIAN
4.0.2
4.0.2
4.0.2
maxSTORIAN
maxSTORIAN
maxVUE
2-2
Description / Explanation
#243 - New Data Look Bad
#2451 - Trend Wrapper crashes when zooming to 1TTH
Interval
#2902(3) Crash after leaving Trend
TrendControl Multiple fixes to zooming and data quality.
#373 St. Johns Similator-Logic call up
#656 - The Annunciator Task does not reload upon station
startup
#791 6- or 7-second Outage after takeover
#1004 - Event Logger multiple HIDs cannot be included or
excluded.
EvtLogger Fixes to HID and severity filtering. Multiple
HIDs and NHIDs now work.
#1005 AOB Downloads Incorrectly
#1078 - Crashes in maxVUE and LSS
#1159 - Trend/maxStorian did not recover from Bad data
Fixed references in a multi-virtual simulation environment.
#1166 - Alarm Summary adding one exclusive HID excludes
all alarms.
#1435 Simulation VDPU references do not resolve following
full download
#1752 - Striping and bad data - Ghent
#1831 - Wrong Java version
#1863 - Can not search (find) in Excel Listings in
MAXTOOLS
#1913 Simulator False Triggers.
Fixed simulation false triggers on database reload from mxt.
#2050 Java Runtime Install Aborts
#2127 - maxVUE Hardware test control broken
#2273 Event Printing is not working
#2305 - maxTOOLS add point failure
#2308 - maxSTORIAN temporary points may not work
#2428 - Routed Writes not working through _sel_pt
#2636 - maxSTORIAN crash on yield
Fixed crash on yield.
#2902 - maxTOOLS ExCEL editor does not 'find'
#2918 - OPC Server failure
#2967 - Simulation "Snapshot" and "Restore" does not work
exactly
Buffers Added logic to inherit a time class from parent so
that IOM table buffers match the DPMS buffer execution.
#3508 IO Config error
IOBusConfig changed to maxval between burst time and
item time in millisecond utilization calculation.
#3672 - MaxTools crashes after multiple searches
#4009 - maxStorian - delete point causes crash
Fixed crash when deleting maxSTORIAN points.
#4035 - Cannot see older data - >30sec rate
#4524 - maxStorian_remote view
#4711 - IMPORT MNT with Button Control
Fixed
4.0.3
4.0.3
Subsystem
maxSTATION
maxDPUTOOLS
4.0.3
maxVUE
4.0.3
maxDPUTOOLS
4.0.3
4.0.3
4.0.3
4.0.3
maxVUE
DPU4F
DPU4F
Remote maxVUE
4.0.3
4.0.3
4.0.3
maxLINKS
maxVUE
DPU4F
4.0.3
4.0.3
4.0.3
4.0.3
4.0.3
4.0.3
4.0.3
4.0.3
4.0.3
4.0.3
4.0.3
4.0.3
maxSTATION
maxDPUTOOLS
DPU4F
DPU4F
DPU4F
maxSTATION
maxLINKS
DPU4F
DPU4F
maxDPUTOOLS
maxSTATION
maxVUE
4.0.3
4.0.3
4.0.3
4.0.3
4.0.3
4.0.3
maxVUE
maxDPUTOOLS
DPU4F
maxVUE
maxVUE
maxVUE
4.0.3
DPU4F
4.0.3
4.0.3
4.0.4
4.0.4
4.0.4
4.0.4
maxVUE
Remote maxVUE
maxSTATION
DPU4F
maxSTATION
maxSTATION
Description / Explanation
#86 - Random maxLSS crashes
#129, #4941 - External reference validation shows incorrrect
errors, Favor Custom block Desc vs Title in Tagname
selection popup
#131, 2151 - Trend Callup is very slow,
maxVUE_maxDNA_TREND_WRAPPER shows Range
Limits at resolution higher than 1024 x 768
#186, 249, 965, 1923, 2771 - Incremental download with
modified custom blocks corrupts DPU, Atom Compiler Object
vs. Custom Function Edits, Prevent concurrent multi-user
editing of a 4E/4F configuration, Nested Custom Functions
should prevent wrapped around referencing, Add printing to
Tabular Detail Display
#233- Date or Time Control cannot be placed on maxVUE
#308 - Custom Function custom category text lost on Failover
#333(3) - Orphaned Atomic Blocks
#559, 4199(3) - Garbage collection not working when using
Remote maxVUE
#749 - maxLINKS floating point writes by exception
#999 - Printing Problems in MaxVue Editor
#1654 - DPU Failover and Take Over cause Bad Quality in
peer DPUs
#1672 Cant acknowledge LSS alarms
#1897 - DlFreezeChk does not report all points
#1905 - dpu4f takeover test fails
#1908(3) - Redundant Virtual DPU Inactive Fatal
#1913 - Simulator False Triggers
#2029 - Automatic daylight savings based on timezone.ini
#2413(3) - WizconHelper Quality goes bad
#2480 - Item queue flooded when AI put in critical
#2522 - Configuration Upload Causes DPU4F to Crash
#2660 - DPU Security Download Does not Work
#3126(3) - Wrong or no events in Report
#3272(3) - Demanding Reports doesn't work in Alternate
Language
#3437 - Browser does not completely support Exposures
#3468 - HID levels Greater than 8
#3682 - Warmup failure when entering text
#3971 IO Inventory control locks up.
#4046 - maxVUE Editor Export does not show line work
#4388 - maxSCRIPT crashes if script source is missing
closing double quote on bitmap function
#4654 - Fixed the cleanup of outgoingsubs in a virtual dpu
after markall, delall
#4747 - Trend Display shows white data
#4781 - Security is stuck at 0
#100 - IOBusConfig is broken
#143 - Complex user attribute with bad data
#344 - Timesync should issue alarm for out of sync objects
#514 - Ladders fail to install
2-3
Subsystem
DPU4F
maxSTATION
maxSTATION
maxSTORIAN
maxDPUTOOLS
4.0.4
4.0.4
4.0.4
4.0.4
4.0.4
4.0.4
4.0.4
4.0.4
4.0.5
OPC Server
maxVUE
DPU4F
maxDPUTOOLS
maxVUE
maxVUE
maxSTATION
maxVUE
maxDPUTools
4.0.5
new.mdb
4.0.5
4.0.5
4.0.5
4.0.5
4.0.5
4.0.5
4.0.5
4.0.5
4.0.5
4.0.5
4.0.5
4.0.5
maxToolsUpdate
MaxRRS
SystemMenu.mn
DPU
Max1Maintain
MaxDPUTools
MaxVUE
MaxDPUTools
EvtCollector
MaxVUE Runtime
Remote maxVUE
new.mdb
4.0.5
4.0.5
4.0.5
MaxToolsUpdate
EwsImport
DPU4F
4.0.5
4.0.5
MaxSTORIAN
Event Collector
4.0.5
4.0.5
4EIOModuleStatus
display
DPU4F
4.0.5
4.0.5
DPU4F
Point Browser
4.0.5
MaxDPUTools
2-4
Description / Explanation
#751 - SW Support for SODIMM
#991 - Event Summary printing contains truncated time field
#1529(3) - Loss of Comm with DBM alarm severity too low
#1628 maxSTORIAN crash due to network failure
#1640 - maxDPUTools does not have QPAT Buffer Limit
Outputs
#1983 - OPCServer write throughput slow
#2196 - Passing text with spaces in display Parameters
#2399 - DPU4F I/O Relay Miss-Operation
#2820 - Custom Block Attribute Category Changes on Upload
#3036 - maxVUE CPU utilization grows
#3745 - _Sel_pt is missing members that existed in Release 3
#3883 - Healthlog alarms not system type
#1104 Corrected tool tips on the System Menu display
#4250 Propagate tagname change to references in the
tabular grid where it can be selected for editing.
#3294 Configuration master for maxTOOLS to add Conf0,
Conf1, Conf2, Conf4, Conf5, Conf7, Conf8 attributes for
excel compile at Gaston; bump rev to 31
#3294 Handle rev 31 of new.mdb (above)
#3310 Correct security level 0 login problems
#1104 Correct tooltips on several buttons
#880 Do not allow adds to the Root group
#388 Fix monolithic excel compiler crash
#1794 Fix crash on updating a version 2.0 configuration
#880 Allow only GRP adds to DPMS Root group
#1603 Prevent backwards version updating
#1955 Add LSS DMT and associated alarm
#1760 Fix Screen printing on multi-monitor
#4231 correct Document 1 not found error
#4187 Configuration master for maxTOOLS to add dummy
lincodes and bump revision to 32
#4187 Handle rev 32 of new.mdb (above)
#4187 Properly handle error on invalid lin-code
#1162 remove reference bubbles on graphical sheets for user
attributes that are referenced by children
#1020 added Registy entries for configuration options
#4738 elminiate memory growth with periodic database
closing
#2654 remove extra copy of control from display
#1444 reject HID text if the name already exists in the DPU;
reject duplicate Relidxs.
#710 do not exit when Save or Save As buttons are clicked
#3869 Show a locked Block with information similar to an
Atom
#1475 purge orphaned template hierarchy folders in an
uploaded configuration; fix incremental download to prevent
problem in the future
Fixed
4.0.5
4.0.5
4.0.5
4.0.5
4.0.5
4.0.5
Subsystem
DPU4F
maxLINKS
Event display
Annunciator task
DPU4F
DPU4F
4.0.5
4.0.5
4.0.5
Report Subsystem
DPU4F
DPU4F simulation
4.0.5
4.0.5
4.0.5
Event Printers
Windows SP2
Graphical Config
4.0.5
4.0.5
DPU4F
MaxDPUTools
4.0.5
SBP VB interface
4.0.5
4.0.5
4.1
4.1
Remote maxVUE
DPU4F
maxSTATION
DPU4F
4.1
4.1
4.1
maxSTATION
maxSTATION
maxSTORIAN
4.1
4.1
4.1
maxSTATION
maxSTATION
maxSTATION
4.1
maxSTATION
4.1
maxSTATION
4.1
DPU4F
4.1
maxSTORIAN
4.1
maxSTATION
4.1
maxSTATION
Description / Explanation
#2581 Added QPAT Buffer simulation slew rate limiting
#3-847 fix crash when other maxLINKS is reset
#4526 improve performance on event retrieval for display
#215 fix crash due to severity 6 alarms
#2144 correct simulator crash
#2252 Correct peer-to-peer references for duplicated
tagnames
#1236 add the ability to specify a default report printer
#3073 fix the 40,000 outgoing subscriptions problem
#192 Provide the ability to configure simulation DPU timer
queues
#3797 correct problem where events were not being printed
#202 add support for Windows Service Pack 2.
#1162 Removed reference bubbles on graphical configurator
for user attributes that are referenced by children
#428 Skip USB device if not in mode 8 or 9
#2037, 4047 Fix custom function instance missing and extra
children
#1743 correct mishandling of VAR_PUBYTE data
conversion
#1608 Correct Remote maxVUE crash
#365 Correct Limiter lockup at or near limits
#213 Trend trace does not show value if quality is not good
#3319, 564 - Added stateful Alarm Defeat and Return to
Normal priority to taggers and ALMREP. Added stateful
alarm defeat to buffers.
#731 - Snapshot list of Simconsole is out of order
#375 - Tracking Point maxVUE Control cannot be resized
#156(3) - maxSTORIAN Status display is recreated as
application
#3190 - GenReportUpdate : Incorrect version displayed
#4864 - DPUEvents: Make delay time customizable
#4607 - TrendWrapper: OnLine Shading Assignments. Restore
good Trace number on invalid entry. Off-line property entry
had the same problem.
#337(3) - Shift Log not generated in IST time zone. Correct
report scheduling in a timezone with a GMT offset that is not
a multiple of an hour
#4613 - The MCSAlarmSummaryCtrl and
MCSAlarmList controls must adjust to the size selected by
2-5
Subsystem
maxDPUTools
4.1
4.1
maxDPUTools
DPU4F
4.1
maxLINKS
4.1
4.1
maxSTATION
maxSTATION
4.1
DPU4F
4.1
4.1
4.1
DPU4F
DPU4F
maxSTATION
4.1
maxSTATION
4.1
DPU4F
4.1
DPU4F
4.1
maxDPUTools
4.1
DPU4F
4.1
DPU4F
4.1
DPU4F
4.1
maxSTATION
4.1
DPU4F
4.1
DPU4F
4.1
DPU4F
2-6
Description / Explanation
#3916 - An incremental download containing custom functions
could not be completed, the message "error comparing user
oject chidren attributes" was displayed
#3911 - Ignore _Backup references in reference validation
#3319 - Added code to eliminate Bad Quality on failover from
the buffers.
#1322(3),2518(3),3266,3846(3),3898(3),454(3) - Problem
Fixes: non zero value for InterMessageDelay parameter causes
the status bit of maxLINK to toggle, maxLINKS crash while
unattended, maxSERVER.exe crash and "Bad References,
Cannot tolerate flaky connection, maxLINK Redundancy
Problem using ABCIPHelper & MSvTCPNet Transport..
#4768 - Event Query does not print events
#1139, 1194, 3666, 1759, 2715 - Added BitBlt drawing
option; added logic to restore non-auto close pop-ups on reexec; Added logic to prompt for a GNAME when adding
Custom Funtion blocks; Added logic to automatically show
and close thumbnail when zooming in Runtime.
#1485 - Fixed ALMREP defeat check that was causing many
events. Recently introduced.
#286 Bios and ATAG fixes for the DPU lockup problem.
#1510 - Disconnecting both network cables crashed the dpu.
#856 - BackupVirtual stops receiving causing a dpu failover
and warm-up failure that left the DPU with 14 services.
#64 Pointbrowser does not unsubscribe when a right click
pop-up is closed causing a buildup of subscriptions in the
provider (DPU).
#1657 incomingsubs value would slowly increase in a
redundant dpu pair.
#4934 - Added grace period for reschedule of outputs and last
bad status to all buffers.
#3074 - Correct double exposure on difference merger after
copy and paste of a custom function.
#599 - Outgoingsubs value increments when a reference to an
external value is changed.
#4198 - Download of a huge configuration used up all of the
long name objects.
#710 - Virtual dpu changed to not exit on a file save (fixed in
4.0, was missing in 4.1).
#763 - Can no longer distribute Adobe Reader 6.0. Version 7
is provided.
#1331 Alarm Reporters that are in alarm are not on the
alarm summary display. A takeover or failover had to occur to
observe this problem.
#4934 The DPU was failing over during workstation
operations such as database upload, point browsing or
displaying sheets with a lot of data.
#1593 - Alarm Reporter will not always post an alarm on an
alarm condition. This problem was created by the recent
addition of the "Return to Normal Severity" attribute.
Fixed
4.1
Subsystem
Graphical Config
4.1
4.1
StartupConfig
maxSTATION
4.1
maxSTATION
4.1
DPU4F
4.1
DPU4F
4.1
maxSTATION
4.1
maxDPUTools
4.1
maxSTATION
4.1
maxSTATION
4.1
maxVUE
4.1
4.1
maxVUE
maxSTATION
4.1
maxVUE
4.1
maxSTATION
4.1
maxVUE
4.1
maxSTATION
Description / Explanation
#2767, 3387, 4050 In testmode, output values are shown.
Also changed tooltip in Editor to say "Show Values/Names"
instead of "Show input Values/Names". Note that analog
outputs connected to boolean inputs do not show values, but
show the connection line as a digital and digital outputs
connected to analog inputs show a value. Analogs to analogs
show a value and digital to digital do not.
#727 - Generate from Scripts button is dangerous
#1761 - Fixed borderschemes that did not process when Main
was re-called.
#3099 - MaxHisRepSvr - fixed crash when formulas are used.
Made usec time calcs check >= 1000000; allow low priority
Sbp messages to trickle among higher priority messages
#1293 - Added "IOM not running" detection. If detected,
generate an alarm and go inactive fatal. Requires a new IOM.
Alarm and state change disabled by mode 8.
#456 - Made alarmtext exposeable in ATAG, DTAG, and
ALMREP. Shell variables that reference alarmtext will still
work, but it would be more efficient to make these exposures.
#3728 - SbpMonitor\maxTRANSview fix crash on display
close.
#388 - Correct starting working directory for excel
compilation.
#2967 - CDStart - Upgrading of adobe should standalone, not
requiring other updates.
#3243 - Firewall - Add additional entries to firewall exception
list.
#4905 - maxLSS - Fix race condition of UnitID vs display
swap subscription updating.
#4640 - improve maxScript performance.
#3788 - Realtimegateway - Plug memory leak communicating
with an RTS.
#3501 - MCSTrendControl - Added quality calculation when
compressing samples.
#1198, 2736, 3319 - StartupConfig - Fix no entry problem
with maxLinks Option switches, added options for virtual
DPU backup, added 58x option for the annunciator.
#1807 Changed the input 1 and input 2 bar graphs on some
point popup displays to show percent of input range as
requested by Problem report 1807. The Point Detail popups
for the following points were changed: Divider, Multiplier,
Upper Select, Lower Select, Two position Switch, Ctl-Divider,
Ctl-Multiplier, Ctl-Upper Select, Ctl-Lower Select, Ctl-Two
Position Switch. The Point Data displays were changed for
the Divider, Multiplier, Upper Select, Lower Select and Two
position Switch.
#8 - EvtServer - Prevent timeout of a count query response by
segmenting into multiple queries of 250 sequential event
record IDs, until all events are covered, rather than one query
on the full record set which can be large.
2-7
Subsystem
DPU4F
4.1
DPU4F
4.1
4.1
maxDPUTools
maxSTATION
4.1
maxSTATION
4.1
maxSTORIAN
2-8
Description / Explanation
#81243,1846 - Corrected DI buffer bugs, AO bump on
failover, Pb on scan - off scan problem, and TimeSync
inclusion of carrier detect in consistent algorithm
#294 - Correct logic in OnSubscribeDone that is looking for
optimized subscriptions. Needed to successfully optimize an
internal reference with a force quality prefix.
#3167 - Ignore command values in online differencing.
#2303 - standard library and displays. Added a new HART
manual 278715 and standard popups for the FB Buffer,
HartStandardV5, HartStandardV6, and HartBeckDriveV5
custom blocks. Changed the standard library to use the new
4.1 master.mdb dated feb 8. Changed library to use Alarm
Reporter instead of DTAG.
#3653(3) TimeSyncPlgin (Realtimegateway) - Make SBP
server members _rtg_nosync and _set_time register as private.
#1337, 1127, 4508, 4382, 4577, 2561, 980 - Problem fixes:
-Method ReadCoreBlock() added a to read core data.
-FlushPutBlock() VERIFY macro added to check
FlushViewofFile result.
-SkipDomainClarifer() changed and pointer added to record
the service name.
-New classes added COfflineSymbol CHashOfflineSymbol to
keep track of the symbols available on external mounts.
-Added constructor to CStorageSymbol to buil offline
symbols. Destructor modified.
-sMergePoint changed to be able to read just the core block.
-Class added to represent external mount points.
-Struct MOUNT replaced with CMount instances.
-New members added to install an external configuration and
to playback it.
-New trend flag added TRN_FLAGS_ALTMOUNT.
-SubscribeDataTrend() and ParseService() changed to support
external mounts.
-Changed to work again with the current lss, button and events
added to
select an alternate mount point among the ones created.
-Changed resorces.
-Code added to let the user browse all the network mounts.
-ImpersonateReplicaUser() member added in order to be able
to clean the storageRoom folder.
-ExitProcess used to terminate Replica instead of
::DestroyWindow.
-ExitProcess used to terminate Replica instead of
::DestroyWindow.
Added checks to FlushViewOfFile call, logged errors on fails.
-Added PID to the log msg printout to help troubleshooting.
Fixed
4.2
Subsystem
maxDPUTools
4.2
maxVUE Runtime
4.2
Point Browser
4.2
maxSTORIAN
4.2
maxVUE Editor
4.2
Time Sync
4.2
Alarm Summary
4.2
Graphical Config
4.2
DlFreeze
4.2
Trend Wrappers
4.2
4.2
4.2
Healthlog
SBP Core Services
Database Summary
displays
Description / Explanation
#2878 Correct duplicate Gname creation on a configuration
update.
#2830 Fix crash in duplicate tagname search when searching
20 or more configurations.
#355 Keep AI, AO, QPAT, maxpac, Tynn, HiCntnn,
LoCntnn consistent when editing
#1440 Correct display parameter expansion of tagnames
that include the string DPn where n is a number
#3-3733 Corrected so that a click on a Button that has zero
size but includes a border will open a pop-up
#3633 Fix slow update rate for Hidden Logic variables
#3-2655 & 3-990 Correct occasional crashes when using the
follow and back options
#4094 Correct problems with the display and data entry of
enumerations that include negative values
#4422 Fix not being able to add temporary points to
collection
#699 Correct logic to allow browsing to shared network
folders
#3-1071 Correct forever Releasing state on Yield request
#776 Fix to allow imported displays to be saved
#1982 Fix to allow saving Cross Reference database
#22227 Fix problem with entering constant values that
caused the error message the parameter is incorrect
#834 Fix problem where maxSTATION would not
synchronize to DBM time
#3119 Fix manual time sync entry causing future time.
#4098 Fix slow update of Alarm Summary display
#1707 Fix not being able to open a display with previously
defined column widths specified
#4659, 1672 Correct crash when using copy/paste functions
#2303, 1162, 3663 Correct problem that did not draw
connection lines and other Sheet drawing problems
#4631 Corrected drawing problems with exported WMF
files
#3-80- Fix occasional crash when dialog is closed in
maxDPUTools
#3-4745 Position on-line dialogs over control instead of
using the Windows random positioning
#333 Clean up Cable Break and other alarms
#714 Correct routing of messages to the proxy
#4469 Correct HID filtering
#2589 Set entire name (not just 16 characters) when
selecting a point
2-9
Subsystem
DPU4F
4.2
RealTimeGateway
4.2
4.2
4.2
Button Control
maxPROXY
maxSCRIPT
4.2
4.2
Dpu4Fsetup
maxLINKS
4.2
Alarm List
4.2
4.2
Virtual DPU
Time State
4.2
4.3
maxTOOLSDiff
DPU4F
4.3
DPU4F
4.3
DPU4F
4.3
DPU4F
4.3
Sizeable Trend
4.3
4.3
4.3
4.3
Alarm Summary
Button Control
Graphical
Configurator
Timesync
4.3
4.3
4.3
DNA Trend
DPU4F
Atom compiler
2-10
Description / Explanation
#3226 Corrected problem with adding Custom Function
blocks containing nested Custom Function Blocks
#3651 Insure timely takeover when an active Hot DPU is
Soft Reset
#3199 Support SOE from a DTAG inside a Custom
Function Block via a shell variable reference
#3984 Fix AO Dropout on failover (with redundant I/O)
#4250 Fixed excessive backup ethernet errors
#3838 Correct problem that caused program to stall when
run as a service
#121 Correct the need to cancel data entry twice
#2684, 3-1108 fix maxProxy crash
#3873 Fix crash that occurs when creating many local
variables
#3-212 Fix crash when running a program via maxScript
#1354 Allow (up to) 12 character DPU Names
#1747 Correct maxLINK switchover using ModbusHelp32
Added Modbus Slave Helper
#4817 preserver frozen state after yield/takeover for Allen
Bradley Helper
#620 Fix filtering via SEV>=x (where x > 1)
#2417 Made Font fize bigger for Alarm List
#3864 Correct DIB Simulation processing
#2015 Fixed inaccurate striping on DPU Details display
after DPU takeover was requested
#3-2281 fix print to file problem
#3373 TC and RTD time class inherit fixed to work with
less than normal time class.
#2790 Edge trigger atoms do not output time 0 on the return
to normal output cycle and the Command atom captures its
inputs on every cycle as well as correct operation of
SingleCmd
#1748 Updated the bios to check the sodimm error bits
during normal startup and mode 3 startup. Added mode 4 ram
test
#4250 - Added delays in net c initialization. Reduces backup
ethernet errors.
#1470 removed debug messages; allow for skipped pen
assignments
#2417 fixed gaps in alarm summary line spacing
#3600 fix crash when writing a string using double quotes
#2698 only show one cross reference when a DPU pair is
the using application
#3238 fix so alarms are generated when Timesync is
minimized
#3-4097 correct display of date
#2625 do not show Bad Ref when forced quality is used
#1210 Corrected atom compiler help text for find function
which was backwards
Fixed
4.3
4.3
Subsystem
DNA History
control
DPU4F
4.3
4.3
IOM
maxDPUTools
4.3
4.3
4.3
4.3
4.3
DPU4F
DPU4F
Trend Control
Alarm List
maxDPUTools
4.3
maxSTORIAN
4.3
4.3
MxsControlPanel
maxSTORIAN
4.3
DPU4F
4.3
4.3
4.3
DPU4F
DPU4F
DPU4F
4.3
4.3
maxSTORIAN
Point Summary
4.3
4.3
maxVUE Runtime
DPU4F
4.3
4.3
maxTRANSPORT
DPU4F
4.3
4.3
4.3
Graphical Config
DPU4F
Graphical Config
4.3
4.3
Backup Virtual
DPU
Virtual DPU
4.3
Atom Compiler
4.3
DPU4F
4.3
4.3
Description / Explanation
#435 corrected check of data type to include data with
quality bits
#1624 Force conversion of NAN and out of range floating
point number in the atom interpreter to be clamped at the max
value used in the dpu.
#247 fixed for read of HART on a long bus
#1464, 1760, 3439 Default the text entry lilmit of attributes
to 40 characters; Prevent drag and drop of the System group
folder in the tree view; Correct omitted ! references in the
cross reference listing
#1349 Fixed Sbp limit counts (counts were not decreasing).
#2898 Prevent CALC MOD function from dividing by zero
#3982 fix maxVUE lockup when using Shade to % of trace
#4085 fix for alarm list not showing alarms
#1624 Eliminate the reading of Custom Function Status
attribute values on Upload
#4650 fix crash when startup file contains blank
maxSTORIAN password
#3933 resize application so entire list is viewable
#5210 fix file Cleanup function that deleted the last
configured file entry
#1866 fix references mis-assignment when doing a hot
upgrade from 4.0 or 4.1
#4044 fix for rare high gain episodes
#369 improve performance of CALC Atom
#3608 fix problems when a DI Buffer is changed from Fast
to Slow
#4906 improved performance of standby disk
#3868 fix crash when refreshing display from one that had
no points
#79 correct restore function for Tracking Point popups
#1269 fix problem seen in our manufacturing floor where
the DPU would restart due to bad MXT files.
#4286 fix problem when Transport View display was closed
#2718 correct inactive DPU to rebuild schedule tables when
the x-position of an atom changes
#133 go to page of selected Atom when opening a Sheet
#2728 do not allow duplicate GNAMEs
#546 fix hang that occurred if there were errors during a
paste operation
#44311 improve performance of warm-up
#1129 add ability for an inactive VDPU to go to stand-alone
mode
#2212 the string returned by the Mid function was not
correct
#4878 add the ability for the Interpreter to handle strings
with intersperces nulls
#4598 fix memory leak
#3048 add the ability to change input registerf from MdbSrv
2-11
Subsystem
VDPU
4.3
4.3
4.3
Report Control
Panel
Module Download
Atom Compiler
4.3
4.3
Backup Virtual
DPU4F
4.3
Quicklog
4.3
Annunciator
4.3
4.3
4.3
maxVUE Runtime
maxLINKS
maxMergeAlarm
4.3
4.3
4.3
4.3
4.3
4.3
Healthlog
OPC Server
Event Access
OPC Gateway
Configurator
Atom Compiler
maxDPUTools
4.3
4.3
4.3
maxDPUTools
DBM
Graphical Config
4.3
maxDPUTools
4.3
DCM
4.3
4.3
maxSTORIAN
maxSTORIAN
4.3
Atom Compiler
4.3
43.
4.3
4.3
maxDPUTools
Differences
maxDPUTools
DPU4F
maxSTORIAN
4.3
maxVUE Runtime
4.3
4.3
4.3
DPU4F
DPU4F
DPU4F
2-12
Description / Explanation
#3-4757 fix failover problem where the DPU lost its
database
#4363 use the Default Report Printer for print preview
requests
#4000 Improve user interface
#3368 added support for constant expressions and constant
ifs. Added support for OD replacement
#2718 rebuild schedule table in inactive hot DPU
#4672 fix crash when a configuration containing two PBs
with duplicate bus addresses was downloaded
#199- fix problem seen at IBM where program does not auto
execute
#3890 correct the Test Sound button to activate the DO to
sound the annunciator.
#621 fix Custom LAST button function
#108 fix high rate of DPUComTransport errors
#4842 correct problem resulting in RCV BAD STAT
FROM dummy alarm
#2190 correct station unreachable status
#662 correct random crash during OPC Gateway connection
#3816 Correct memory leak in Event Summary display
#1442 allow for delimeters other than period
#275 fix adding a string to the output buffer
#2263 correct problems trying to change a Custom Function
block to a different one
#2392 eliminate duplicate tagnames in printer report
#3-3973 correct truncated event messages
#3843 correct drawing of polygons and lines on multi-page
Sheets
#120 Disallow the use of the shorthad IP address [] during
incremental install
#3266 correct toggling of status bits when a non zero value
is entered for InterMessageDelay parameter
#4268 correct maxSTORIAN crash during Import
#22 when a request for historical data does not specify a
statistic, return the sample statistic
#936 correct Check method and Write method to handle
Long, Float, and Text type shell variables
#1331 correct reporting for exposure editing
#1508 improve custom complex definition entry
#2960 correct ALRMCLCK local time option problem
#1932, 1433, 3692 fix problem where Export never
completes and other Export problems
#147 do not clear the selected point when swapping to a new
display
#1304 fix DPU that locks up
#2298 fix PB failure on incremental download
#2747 correct incorrect alarm for AIB and PB
Metso Automation 278700
Fixed
4.3
4.3
4.3
Subsystem
DPU4F Detail
display
DLFreeze Check
DPU4F
4.3
4.3
DPU4F
maxVUE Runtime
4.3
4.3
maxVUE Editor
DPU4F
4.3
maxDPUTools
4.3
DPU4F
4.3
VDPU4F
4.3
maxVUE Runtime
4.3
4.3
4.3
4.3
maxTOOLS
CDStart
DPU4F
mxsConfig
4.3
maxLINKS
4.3
4.3
Tracking Point
configuration
DPU4F
4.3
DPU4F
4.3
4.3
Backup Virtual
MCS List Control
4.3.0.2
DPU4F
4.3.0.2
4.3.0.2
4.3.0.2
maxSTATION
maxVUE Runtime
maxVUE Runtime
4.3.0.2
maxSTORIAN
4.3.0.2
4.3.0.2
maxVUE Runtime
maxVUE Runtime
4.3.0.2
maxVUE Runtime
Description / Explanation
#823 correct status for IRIG-B on inactive DPU
#1466 fix to allow use of this control in maxVUE
#965 correction to allow addition of CB via Graphical
Configurator
#2337 correct PB command change detection
#2553 correct drawing of large bitmaps via Terminal Server
connections
#1876 correct momentary drawing of Freeze Check dialog
#3480 Stop processing of SOE events ina secondary DPU4F
with redundant I/O
#1011 correct configuration masters for missing ATAG
exposures; hide EB atom
#2426 stop re-subscribes for references of the form
[^]tag.attrib where the tag resides in the same DPU
#3438 fix crash when multiple VDPUs are started in one
maxSTATION
#4079 fix truncated maxVUE Runtime display for maxVUE
that spans more than one monitor
#4105 correct crash during 58x migration import
#2775 correct installation process that skips needed steps
#4636 fix AutoMan atoms FailCoe for Target out of Range
#4482 preserve temporary trend assignments when reinstalling a maxSTORIAN configuration
#1569 correct Modbus helper to handle writes of negative
values
#465 open Tracking Point Configuration tool on the correct
monitor of a multi-monitor maxSTATION
#1424 a forced quality reference to an exposure wasnt
always passing on the forced quality
#3969 fix problem where TOTL atoms does not capture
ResetVal on Reset input
#71 correct to work with dual core or multi-threaded PC
#2159 fix to show data entry popup (on List with header &
Border scheme)
#4313 correct limitation for redundant Burst AO modules
(no longer limited to 4)
#1775 LSS and other programs abort due to dongle failure
#2406 Dual language description broken in event summaries
#4373 Fixed Defeat button to recognize values greater than
1
#1355 Multicast subscription now honor the priority of
incoming packets instead of changing them to normal.
#3818 maxVUE re-exec as Operater hangs for a time
#1985 - maxVUE Runtime crash on re-exec with non-auto
close pop-up
#275 - DPU4F Security View Popup updated to support
unbracketed IPs
2-13
Subsystem
maxArchiver
4.3.0.2
maxDPUTools
4.3.0.2
4.3.1
4.3.1
maxDPUTools
BackupVirtual
Report subsystem
4.3.1
DPU4F
4.3.1
4.3.1
4.3.1
maxDPUTools
PID Display
maxDPUTools
4.3.1
4.3.1
4.3.1
4.3.1
4.3.1
4.3.1
4.3.1
4.3.1
4.3.1
4.3.1
4.3.1
4.3.1
4.3.1
DPU4F
maxDPUTools
DPU4F
excelCompiler
Event Summary
VB SBP Control
maxSTORIAN
maxVUE Editor
DPU4F
DPU4F
maxRRS
maxPROXY
Trend displays
4.3.1
4.3.1
4.3.1
4.3.1
4.3.1
4.4
4.4
Archiver tasks
maxVUE Runtime
maxSTORIAN
maxSTORIAN
Alarm Summary
MCSEnumFields
Trend displays
4.4
Startup
4.4
4.4
4.4
4.4
4.4
maxDPUTools
Classic
maxSTORIAN
FindBadRef
maxDOCS
maxVUE
4.4
Timesync
2-14
Description / Explanation
#3-2326 - Only require closure confirmation on a mouse click
selection of the close button in the title bar, not if an external
close request (shutdown or logoff)
#1506, 4776 Fixed lost attributes on Copy and Incremental
download. Fixed slow online differences.
#4081 - maxDPUTools crash after configuration update
#71 fix to run on multi-threaded or dual core machines
#801 add detection/display of Export Feature to Control
Panel
#2513 add default text for TrTxt and FlsTxt attributes of
DTAG Atom
#4667 added Operator Action events for Download action
#1480 correct text for overview index
#4760 correct crash in creation of SQL with text containing
special characters
#4667 added events for various DPU takeovers
#3414 fix Import from database using Gname lookup
#2261 fix temporary string storage in Interpreter
#1423 correct ladder compile crash
#3846 improved event list filtering
#369 corrections for return of Variant data
#1579 fix incomplete import merge
#4887 correctly save Imported displays
#3244 fix FB on hot failover
#2024 fix DPU reset for failed re-exec case
#240 fix incorrect Operator auto login level
#3-3057 correct proxy data access
#280 correct selected point setting with maxSTORIAN
prefix
#2348 correct crash on Administrator invocation
#4814 correct navigation via rectangle on 2nd monitor
#3091 fix file clean crash
#799 fix SBP errors when running export
#3906 fix crash when Summary is in a pop-up
#3705 fix enumeration of DPU4F text
#2084 fix start time for 8-hour intervals to start on 8-hour
boundary
#4554 fix for VDPU startup which was ignoring the delay
time parameter
#3049 add validation of Gname and Tagname on import
#1278 improve performance during maxSTORIAN failover
#2967 fix crash when processing FBs
#1702 Updates to 278610, 278719, new 278724
#2119 show correct DPU name when following a peer-topeer reference using [^] syntax
#1454 delay TimeSync alarm output until consecutive bad
readings are detected
Fixed
4.4
Subsystem
Startup Config
4.4
4.4
4.4
4.4
4.4
maxVUE Editor
maxDPUTools
maxDPUTools
NetAnalyze
Event Subsystem
4.4
4.4
OPCGateway
ExcelMerge
4.4
4.4
4.4
Sizable Trend
Wrapper
maxTOOLS
Database
Button control
Alarm Summary
4.4
Alarm Summary
4.4
Buffer Pop-ups
4.4
4.4
Various workstation
programs
maxSCRIPT
4.4
4.4.1
maxDomainConfig
maxPROXY
4.4.1
4.4.1
OPCGateway
maxLSS
4.4.1
maxLSS
4.4.1
4.4.1
maxSTORIAN
subsystem
maxDPUTools
4.4.1
maxDPUTools
4.4.1
HWTest displays
4.4.1
maxDPUTools
4.4.1
maxDPUTools
4.4.1
maxLINKS
4.4
Description / Explanation
#331 Added the ability to specify slower SBP subscription
rates for a Virtual DPU
#2557 Fix high CPU usage when opening multiple Sheets
#2780 Prevent duplicate names via find and replace
#4945 Prevent SBP connection timeout during Upload
#3834 Improve Network Analyzer information
#1125 Add the ability to access merged events from multiple
Event Servers
#47 fix what appears to b a memory leak while doing writes
#4341 Add missing lookup of Gname used in a modular
excel parameter reference
#2635 Correctly display user defined descriptions and UOM
text
#3470 updated to Rev 33 with DHYCNT attribute for excel
compiler
#600 allow parameterization of Write Point Value
#1840 fix memory growth in maxMergeDPUAlm when
paging on the Alarm Summary display
#2032 fix for alarm severity filtering in Ack/Time sort for
alarms issued by work Station programs.
#3097 Added State Text SIM EU for simulation state
value 2.
#4556 fixed various programs to open pop-ups on the same
monitor (of multi-monitor stations) where request was initiated
#2250 fix Editor debugging of scripts that caused the script
to work in Runtime but not in Editor
#644 allow configuration of 16 domains per workstation
#3601 fix for peer to peer communications - rapidly retries
once.
#47 Limit write queue to one subscription update.
#3431 Change the description of a Deadman Timer (DMT)
point to Possible program failure rather than Keyboard
support
#4242 Changed the periodicity of disk sizing checks from
every 2 minutes to once an hour
#1813 Allow for longer attribute name assignments in the
maxSTORIAN database.
#2615 Correct bad instance records with a self-parent
reference
#1138 Split up database operations that were causing
excessive file growth when using the graphical editor
#2839 fix displays that were doing button click logic on
initial display call-up
#3049 Correct failure of import update by tagname. A
duplicate tagname should be allowed.
#2444 Add child attribute exposures to Group detail in
Expert view.
#3944 Bad float conversion and not remembering quality
caused write_only points to write on every data update
whether the value changed or not (MsvImmData).
2-15
Subsystem
Annunciator Task
4.4.1
EvtServer
4.4.1
4.4.1
Point Browser
4.4.1
SP1
4.4.1
SP1
4.4.1
SP1
Manual Updates
4.4.1
SP1
4.4.1
SP1
FileSyncServer
4.4.1
SP1
Event Summary
display
4.4.1
SP1
4.4.1
SP1
Sizeable Trend
Wrapper
EvtSync display
4.4.1
SP1
4.4.1
SP1
4.4.1
SP1
4.5
4.5
4.5
Enum Fields
control, OpLogic
control, maxServer,
Replica,
SbpNetWrapper
TimeSync
4.5
4.5
OPCGateway
maxToolsDialog
2-16
maxLSS
maxDPUTools
EvtServer &
EventAccess
OPCGateway
EvtArchiver &
maxArchiver
maxLINKS
Description / Explanation
#2789 fix Terminal Server audible alarms to loop
continuously when configured to do so.
#4809 fix infrequent crash caused by multi-thread access to
a shared list
#3106 updated Disk Usage display to be more information
including a help button.
#36 added middle mouse wheel scroll support for the
browser detail view.
278 705, 278715, 278589
#2405, 4374 Correct memory leak; correct maxSCRIPT
problem with variables created for multi-monitor stations
#4205 Read the registry for the path to launch MS-Access
version 8 for configuration update. This allows co-installation
of MS-Access 97 and Office 2000.
#2755 fix crash when doing multiple station file
synchronization
#4662 Improve retrieval performance; correct Daylight
savings transition problem; added historic vs. realtime
retrieval status; modified wait time of retrieval for new events
from 20 seconds to 10 seconds; allow 2 seconds for Edit
Actions.
#4662 increased default font size from 10 to 12; added Font
property page to allow further selection; expanded the range of
default relative start time from 24 hours to 90 days; modified
caption state text.
#3429, 4473 fix on-line changes for pop-ups; fix faulty bar
pointer when using t.rangeLim instead of a constant
#1522 update the Event Sync status dipsly to run on any
workStation (not just where the EvtSync program is running);
updated the display to include alternate EvtSync server status
#4798 corrected display presentation for long time spans
with large intervals
#2648 correct problem with abrupt shutdown of the
OPCGateway (such as happens when a station is restarted)
#1357 ensure that next time to archive persists through a
station restart
#1220 fix ABCIPHelper and AllenBradleyHelper to support
TCP communication for certain AB PLC types
#966 correct an SBP interface call which resulted in random
crashes
Fixed
4.5
Subsystem
maxDPUTools
4.5
4.5
maxDPUTools
OPCServer
4.5
4.5
4.5
4.5
DOB pop-ops
OPCServer
Event Management
display
MCSTextState
control
PointBrowser
4.5
SimTransport
4.5
CSVExport
4.5
4.5
maxDPUTools
SRMerge
4.5
mxsPanel
4.5
OPCHDAServer
4.5
4.5
maxSTORIAN
CSVExport
4.5
OPCAEServer
4.5
4.5
SBP/EvtSync
maxVUE
4.5
4.5
4.5.1
maxDPUTools
maxSTORIAN
maxDPUTools
4.5.1
4.5.1
maxDPUTools
maxDPUTools
4.5.1
maxDPUTools
4.5.1
4.5.1
4.5.1
4.5.1
maxDPUTools
ACNSetup
maxVUE
OPCGateway Suite
4.5.1
AB EIP
4.5
Description / Explanation
#2172 add an initial file selection dialog for Open New
Copy to the welcome screen
#1954 add wheel scrolling to the tabular detail grid
#360 add read only ModeCh to the exception list to default
its type to float
#4109 change to recognize any non-zero value as true
#3148 fix version 3 connection failure
#1426 fix to filter out duplicate events
#3-3733 Allow a zero size text state with border to provide
display navigation.
#3233 Close the wks.ini file after use. Fix wandering focus
rectangle.
#3028 Correct routing on incremental download that caused
install download errors.
#1758 Remove extra blanks in output, that caused MSEXCEL problems.
#852 corrects errors in IMPORT library revision mismatch.
#2587 Reduce the detail in the log file that made it too large
to view.
#3421 Fix crash when using mouse wheel to change
maxSTORIAN source.
#806 Sort the uploaded identifier from maxSTORIAN, for
use in client browsing.
#621 Provide HID alias support to configured Tagnames.
#3339 Added options to include/exclude row header. Allow
date format selection via a limited set of radio style sub-menu
entries.
#2969 Added option to enable/disable alarm severity rescaling from 1 to 5 into the 1 to 1000 OPC range.
#1622 Corrected PreserveValue for extended string in reply.
#1682 Corrected non-updating Graphical Configuration
Sheet in runtime.
#1468 Added I/O cross reference display and output.
4040 Corrected dongle X bit handling.
Allow 96 custom attributes and double sized atom object with
new ACN 5.1.
Added MIO Address consistency validation.
#2048 - During Download, queue and retry any attribute
errors.
#4817 - Upon opening a configuration, adjust any SvcY
values to be 275 maximum.
New DPU 5.1 master with EIBC added.
Added EIBC programming support.
#1595 - Fix Border Scheme database corruption.
Rewrite for Performance improvements, error fixes, and
addition of alarming for Rovisys, 50 running instances.
Fixed a problem reading S record files.
2-17
Subsystem
maxVUE
4.5.1
Sizable_TREND_
WRAPPER
4.5.1
4.5.1
4.5.1
MCSTrendControl
TrendMenu
PointBrowser
4.5.1
4.5.1
4.5.1
IOInventoryControl
maxDNA_IBCStat
us
maxVUE_maxDN
A_HWTest4E
MaxTransport
4.5.1
4.5.1
Gparted
maxVUE
4.5.1
maxDOCs
4.5.1
maxVUE Editor
4.5.1
maxOPCServer
4.5.1
AB Links
4.5.1
4.5.1
maxVUE
Event summary
4.5.1
SRCheck V1
4.5.1
maxArchiver
4.5.1
evtArchiver
4.5.1
mxsPanel V2
4.5.1
netAnalyze
4.5.1
maxRRS
4.5.1
mxsConfig
4.5.1
2-18
Description / Explanation
4-2968, 4-4525: Correct access of VDPU; correct border
scheme drawing using BitBlt option; fix "Space evenly" not
writing new Atom positions.
5-4101 - Show Limit values instead of tag.attrib; limits dialog
is not longer sizeable; position pen info together; show pen
number inside color box only when "Display Trace No."
property is checked
5-4101 - Allow more than 10 vertical grid lines.
5-4101 - Add button to shown/change tag vs description mode.
4-2968 - Correct access to VDPUs (by using connection
number when accessing by IP address).
Update to add EIBCs
Update to add EIBCs
Update to add EIBCs
Registry updated to increase UDP buffering to 32K to reduce
respooling.
Update to this tool included on Install Release Disk.
Popups for EIBC control, Detail, as well as individual control
popups to allow redundancy.
278705 DPU4F IRIG, 278609 Sys Resources delete Sync
RTG, 278597 maxDPUTOOLS add MIO validation section.
5-1756 - Fix printing of current sheet. For invalid references
or peer-to-peer on inputs, do not print the page number box.
1251 - Add Runstc to the exception list for determining write
data type. Assume Float.
Added a new port config command to specify message
timeouts for multi-drop links.
4-529 Popup corrections
5-1318 - Remove event severity 6 problems with MergeAlarm
Comm alarms.
5-4348 - Correct crash due to null block / pointer mishandling.
5-764, 5-3239 - Prevent redundant running copies; Modify
Current mount Serial no recognition; Remove error
notification MessageBox.
5-3239 - Prevent redundant running copies; Modify Current
mount Serial no recognition.
4-427 - Add keystroke processing delay of 1/2 second, to
allow quick consecutive entry of a name match before
applying the name filter.
4-2865 - Prevent intermittent red icon flashing by extending
the timeout from 5 to 10 seconds on receiving a new message.
5-4392 - Correction for badly formed read request without a
".attribute" causing maxVUE Runtime hang.
5-3197 - Apply limit of 120 seconds to subscription min and
max times. Trim String entry of Template, Name, and
Attribute text in grid before saving. Add Mouse wheel
scrolling.
Fixed
4.5.1
Subsystem
FileSyncServer
4.5.1
maxDOCS
4.5.1
EvtSync
4.5.1
maxVUE
4.5.1
MCSBarControl
4.5.1
maxFileSyncViewer
4.5.1
BackupVirtual
4.5.1
Event Summary
4.5.1
DB Summary
4.5.1
4.5.1
4.5.1
4.5.1
4.5.1
4.5.1
SimTransport
AB Link
Firewall
HWTest4E
DlFreezeChk
SBPNetWrapper
4.5.1
maxDPUTools
4.5.1
MAXHisRepSvr
4.5.1
maxDPUTools
4.5.1
4.5.1
MCSListControl/M
CSSglPtValueContr
ol
MCSBSEditor
4.5.1
AllenBradleyHelper
4.5.1
SRMerge
4.5.1
MCSClass
4.5.1
maxVUE
4.5.1
MarkIVSlave
Description / Explanation
5-3557 - Fix crash when copying Folders into a Master
Group.
4-4192, 5-3799 - 4F hardware for Mode 8, GC page
numbering clarifications, accuracy spec for IOP321 analog
output.
5-1412 - Repair merge results. Correct infinite transfer retry
on a merge error.
5-785,1012) - fix crash when Restore 20th popup; also fix
crash when using "Save Selection" with Layers Dialog.
5-4855 - Bar chart alarming now occurs at the limit values
instead of only when the limits were exceeded.
5-3364 - Correct tooltip inconsistency, do not show stations
not in my domain.
Updates to support the 9600 byte extra large cell size in
Version 5.1.
5-3071 - Include the milliseconds of SOE events when
applying any on screen filtering by time to allow filtering
within the same second.
5-1800 - Filter out custom block children from the manual
summary.
4-3042 - Fix routing to VDPU when Secondary is Active.
fixed the ABWordRngWrite.atom custom block.
2736 - Add OPCGatewayValidate to the exception list.
4-1211 - Remove debug messages.
4021 - OD buffer not showing as frozen.
3024 - need to preserve variant data request array in
subscribing for history and also events.
5-2166 - Correct 4.4 and 5.0 Configuration masters and
libraries to add ATAG and DTAG missing Track enumeration
value for the Mode attribute.
WIJ-223422 - Init values passed to printer enumeration
function; check return status of same function - fix for crash.
3868) - workaround fix for zeroed Hi/LoCountxx attributes in
HART AIB. Custom limits are re-tried at the end of download.
5-3518 - put back logic: control must have both width &
height <= 10 pixels to draw as a black rectangle.
4-1595 - add "/FixCorruption" parameter to allow the user to
move scheme lines up and down from/to default position.
Fixed Protected Typed Logical Read & Write with 3 Address
Fields and Write problems for AB EIP using SLC5/05.
5-2958 - Updated to provide minimum hourly interval
repeating samples to fill the gap when data updates are slower
than one hour.
4-1349 - Position Trend Selected Point dialog on monitor that
requests it.
4-529 - Correct Alarm Text Wrapper Calcs for dashes in
tagnames; correct check in scripts for EU Simulation.
Added protocol support for GE Mark IV Data Dump link
using SCM card.
2-19
Subsystem
NetAnalyze
4.5.1
4.5.1
HealthLog
maxDPUTools
4.5.1
maxDPUTools
4.5.1
MaxMergeAlm
4.5.1
MaxMergeDPUAl
m
4.5.1
maxVUE
4.5.1
4.5.1
4.5.1
OPCGatewayConfi
g
maxScript
maxScriptEditor
4.5.1
Modbus
4.5.1
AllenBradley
4.5.1
AllenBradleyEIP
4.5.1
maxDPUTools
4.5.1
maxDPUTools
4.5.1
ACNSetUp
4.5.1
4.5.1
4.5.1
4.5.1
Logo Updates
Sizable_TREND_
WRAPPER
EvtServer
CsvExport
4.5.1
SbpNetLibrary
4.5.1
maxDPUTools
2-20
Description / Explanation
4-4956 - ignore arp request messages that had invalid IP
source addresses, these were resulting in bogus station list
entries.
5-303 - Fix Overflow error with > 124 DPUs in DpuList.ini
5-1286) - Apply auto reference updating when a tagname is
modified via Find and Replace. Include tagname references
with '!' prefix.
Added 5 new replace action options: Find Only - manual edit,
Insert as Prefix, Insert as Suffix, Insert Before Match, and
Insert After Match.
5-0037 - When alarm is created, wait a fixed period before
reporting it to LSS. If another identical alarm is not created
within this period then do not report it, otherwise report it and
process as usual.
5-0037 - When alarm is created, wait a fixed period before
reporting it to LSS. If another identical alarm is not created
within this period then do not report it, otherwise report it and
process as usual.
5-2555 - Various fixes to Graphical Configurator for Page
Numbering and lines frawn from off-page connectors.
5-3546 - Correct browsing problem with un-normalized tree
hierarchies.
Add ability to set SBP data quality in LSS variables.
Add ability to recognize new maxSCRIPT strings and
capitalize them appropriately.
Added processing of timeout message from SCM card.
Increased timeout to 60 secs. LinkFail set to false when
ResetStats command is given.
Added processing of timeout message from SCM card.
Increased timeout to 60 secs. LinkFail set to false when
ResetStats command is given.
Added processing of timeout message from SCM card.
Increased timeout to 60 secs. LinkFail set to false when
ResetStats command is given.
5-4957 - Correct errant Atag.AlmSev exposure resetting to
zero when slected in the custom tab.
Update 5.1 maxDpuTools master with addition of MDIB16
and MDOB16 services.
Update Flash Warning message. Fix processing of nonexistant IBCs.
updates for "Metso Automation USA Inc." and for 2010.
Updates for custom control compatibility.
2072 - EvtServer retrieval crash corrected.
3024 - Revitalize CsvExport with progress bar and grid
display.
3024 - Serialize Historian collection retrieval. Change delegate
callback technique for thread performance and prevent
stallout.
Updated DPU masters 4.4 and 5.1 for added EB attributes.
Fixed
4.5.1
Subsystem
maxDPUTools
4.5.1
maxSTORIAN V2
4.5.1
maxSTORIAN V2
4.5.1
maxLSS
4.5.1
maxDPUTools
4.5.1
maxMergeDpuAlm
4.5.1
HotFixInstall
4.5.1
maxVUE Editor
4.5.1
BackupVirtual
4.5.1
CSVExport
4.5.1
maxDPUTools
4.5.1
maxDPUTools
4.5.1
4.5.1
maxDPUTools
maxDPUTools
4.5.1
4.5.1
maxDPUTools
HealthLog
4.5.1
4.5.1
4/5/1
MCSButtonControl
maxVUE
maxVUE
4.5.1
4.5.1
DpuEvents
maxVUE
4.5.1
maxSTORIAN 2,
SBP, Trend Control
maxSTORIAN 2
maxLSS
4.5.1
4.5.1
Description / Explanation
4-1692 - Extend the DPMS.AppFlag signal after a full
download to 5 seconds after a 2 seconds delay, rather than 2
seconds.
5-39,4-3665,5-2101 Correct memory leaks, missing data in
retrieval, looping on edit merger.
5-713) Remove restriction on retrieval intervals less than 5
minutes being part of an enumerated set requiring roundup.
5-1789) Eliminate nuisance alarms on startup by changing the
default DMT timeout to 120 seconds rather than 10.
5-4205 partial fix) If a custom block is copied and pasted
across DPUs, the template is missing. Abort upload in this
scenario to prevent a bad configuration.
2-21
2-22
Subsystem
maxDPUTools /
Browser
Point Browser
maxDOCS Release
manuals
Description / Explanation
5-1120 - Updated the Atag/Dtag HTML configuration help to
describe the Track option for the Mode attribute.
5-1406 - Correct row placement of ">" exposure indication.
(4-34, 4-661, 4-1280, 4-4280, 4-4529, 5-1767, 5-2889, 54877)
Added better instructions for doing repair and
upgrades for DPU4E and DPU4F.
Added event details to the Atoms and MIO Buffer
manuals.
Fixed mixed system time sync in Sys Resource
manual.
Added detailed description of Redundant BEM
configurations to the maxPAC manual and 564 BEM
manual.
Added description of quality propagation to
maxSCRIPT manual.
Added documentation about running multiple virtual
DPUs to the maxDPU Auliliary and Simulation
manual.
Added information about station setup to the Aux
Function manual.
Description of comparing personalities on a
Positioning Module.
Added Description of of the Atag and Dtag Track
option for the Mode attribute. Also Updated the
HTML configuration help.
Added description of the new maxDPUTools
Bookmark feature for nodes in the tree control.
Added instructions to the ACN-MIO Overview about
resetting the ACN after flashing the IBC.
Improved the description of using the maxSTORIAN
Default template for online trend assignment
additions.
Updated Alarm messages regarding Healthlog
alarming for memory usage.
Fixed
4.5.1
Subsystem
maxDOCS
Manuals continued:
Description / Explanation
Volume 1
278590 - DPU4E_HdwGuide
278705 - DPU4F_HdwGuide
278610 maxPAC
278558 - alarm messages
Volume 2
278594 - Auxiliary Functions
278605 - maxDPU Auxiliary Functions
278609 - system Resources,
278597 - maxDPUTools
Volume 3
278595 - bem
Volume 5
278589 atoms
278623 maxLINKS
278730 maxSTORIAN
278588 - maxScript
278707 - Virtual DPU Simulation
278704 - Positioning Module
Volume 6
278733 - ACN/MIO Overview
278732 - MIO Buffers
2-23
Chapter 3
Special Instructions for Upgrades
Overview
If you are upgrading from an earlier version of maxDNA, please follow
these extra steps to ensure that your system gets updated properly. If this
is a first-time installation of maxDNA, skip this section.
2-24
2-25
2-26