Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
of ThyssenKrupp
Steel
ThyssenKrupp Bausysteme
tk
Load tables
Hoesch Trapezoidal sheet
according to DIN 18,807
positive position
Proviled sheet
Positive position
Dimmensions in [mm]
A
The trapezoidal profile used as a load-bearing building component for roofing and ceiling systems is only
suitable for foot traffic by single persons after load-distributing measures have been taken (e.g., wooden
planks). The laying plans should contain information to this effect.
Line *:
Lines L/:
Permissible load taking account of a limitation of deflection of max f L/... . These values also apply to
the lower part of the tables for two- and three-span girder if they are smaller than those quoted line *.
The tables are not a substitute for the structural analyses required for the building design. The permissible load values
have been determined in accordance with the provisions of DIN 18807.
Observe the maximum length supplied, especially in the case of multiple-span girder.
Span L[m]
tN
g max f
0.63 6.0
*
L/150
L/200
L/300
0.75 7.2
*
L/150
L/200
L/300
0.88 8.4
*
L/150
L/200
L/300
1.00 9.6
*
L/150
L/200
L/300
1.25 11.9
*
L/150
L/200
L/300
A company
of ThyssenKrupp
Steel
perm. q [kN/m2]
2.00 2.20 2.40 2.60 2.80 3.00 3.20 3.40 3.60 3.80 4.00 4.20 4.40 4.60 4.80 5.00
1.70
1.26
0.95
0.63
2.27
1.79
1.34
0.89
2.98
2.24
1.68
1.12
3.64
2.73
2.05
1.36
4.90
3.44
2.58
1.72
1.40
0.95
0.71
0.47
1.87
1.34
1.01
0.67
2.46
1.69
1.27
0.84
3.01
2.05
1.54
1.03
4.05
2.59
1.94
1.29
1.18
0.73
0.55
0.37
1.57
1.03
0.78
0.52
2.07
1.30
0.97
0.65
2.53
1.58
1.18
0.79
3.40
1.99
1.49
1.00
1.00
0.57
0.43
0.29
1.34
0.81
0.61
0.41
1.76
1.02
0.77
0.51
2.15
1.24
0.93
0.62
2.90
1.57
1.17
0.78
0.87
0.46
0.35
0.23
1.16
0.65
0.49
0.33
1.52
0.82
0.61
0.41
1.86
0.99
0.75
0.50
2.50
1.25
0.94
0.63
0.75
0.37
0.28
0.19
1.01
0.53
0.40
0.26
1.33
0.67
0.50
0.33
1.62
0.81
0.61
0.40
2.18
1.02
0.76
0.51
0.66
0.31
0.23
0.15
0.89
0.44
0.33
0.22
1.16
0.55
0.41
0.27
1.42
0.67
0.50
0.33
1.91
0.84
0.63
0.42
ThyssenKrupp Bausysteme
0.59
0.26
0.19
0.13
0.78
0.36
0.27
0.18
1.03
0.46
0.34
0.23
1.26
0.56
0.42
0.28
1.69
0.70
0.53
0.35
0.52
0.22
0.16
0.11
0.70
0.31
0.23
0.15
0.92
0.38
0.29
0.19
1.12
0.47
0.35
0.23
1.51
0.59
0.44
0.30
0.47
0.18
0.14
0.09
0.63
0.26
0.20
0.13
0.83
0.33
0.25
0.16
1.01
0.40
0.30
0.20
1.36
0.50
0.38
0.25
0.42
0.16
0.12
0.08
0.57
0.22
0.17
0.11
0.75
0.28
0.21
0.14
0.91
0.34
0.26
0.17
1.22
0.43
0.32
0.22
0.38
0.14
0.10
0.07
0.51
0.19
0.14
0.10
0.68
0.24
0.18
0.12
0.82
0.29
0.22
0.15
1.11
0.37
0.28
0.19
0.35
0.12
0.09
0.06
0.47
0.17
0.13
0.08
0.62
0.21
0.16
0.11
0.75
0.26
0.19
0.13
1.01
0.32
0.24
0.16
0.32
0.10
0.08
0.05
0.43
0.15
0.11
0.07
0.56
0.18
0.14
0.09
0.69
0.22
0.17
0.11
0.93
0.28
0.21
0.14
0.29
0.09
0.07
0.05
0.39
0.13
0.10
0.06
0.52
0.16
0.12
0.08
0.63
0.20
0.15
0.10
0.85
0.25
0.19
0.12
0.27
0.08
0.06
0.04
0.36
0.11
0.09
0.06
0.48
0.14
0.11
0.07
0.58
0.17
0.13
0.09
0.78
0.22
0.17
0.11
ThyssenKrupp
perm. q [kN/m2]
1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 3.20
End supporting with bA = 40 mm, Intermediate supporting with bB 60 mm
5.29 4.41 3.46 2.65 2.10 1.70 1.40 1.18 1.00 0.87 0.75 0.66
5.29 4.41 3.46 2.65 2.10 1.70 1.40 1.18 1.00 0.87 0.75 0.66
5.29 4.41 3.46 2.65 2.10 1.70 1.40 1.18 1.00 0.83 0.67 0.56
5.29 4.41 3.46 2.65 2.08 1.52 1.14 0.88 0.69 0.55 0.45 0.37
7.15 5.96 4.63 3.54 2.80 2.27 1.87 1.57 1.34 1.16 1.01 0.89
7.15 5.96 4.63 3.54 2.80 2.27 1.87 1.57 1.34 1.16 1.01 0.89
7.15 5.96 4.63 3.54 2.80 2.27 1.87 1.57 1.34 1.16 0.96 0.79
7.15 5.96 4.63 3.54 2.80 2.15 1.62 1.24 0.98 0.78 0.64 0.52
9.49 7.91 6.08 4.66 3.68 2.98 2.46 2.07 1.76 1.52 1.33 1.16
9.49 7.91 6.08 4.66 3.68 2.98 2.46 2.07 1.76 1.52 1.33 1.16
9.49 7.91 6.08 4.66 3.68 2.98 2.46 2.07 1.76 1.47 1.20 0.99
9.49 7.91 6.08 4.66 3.68 2.70 2.03 1.56 1.23 0.98 0.80 0.66
11.70 9.75 7.42 5.68 4.52 3.66 3.03 2.54 2.17 1.87 1.63 1.43
11.70 9.75 7.42 5.68 4.52 3.66 3.03 2.54 2.17 1.87 1.63 1.43
11.70 9.75 7.42 5.68 4.52 3.66 3.03 2.54 2.17 1.79 1.46 1.20
11.70 9.75 7.42 5.68 4.50 3.28 2.47 1.90 1.49 1.20 0.97 0.80
16.89 13.60 10.00 8.09 6.51 5.27 4.36 3.66 3.12 2.69 2.34 2.06
16.89 13.60 10.00 8.09 6.51 5.27 4.36 3.66 3.12 2.69 2.34 2.02
16.89 13.60 10.00 8.09 6.51 5.27 4.36 3.59 2.82 2.26 1.84 1.51
16.89 13.60 10.00 8.08 5.67 4.14 3.11 2.39 1.88 1.51 1.23 1.01
End supporting with bA = 40 mm, Intermediate supporting with bB = 0 mm
3.23 2.69 2.30 2.02 1.70 1.44 1.23 1.07 0.94 0.83 0.74 0.66
4.26 3.55 3.04 2.66 2.26 1.93 1.67 1.46 1.29 1.15 1.01 0.89
5.99 4.99 4.28 3.74 3.15 2.67 2.30 2.00 1.75 1.52 1.32 1.16
7.59 6.32 5.42 4.74 3.97 3.36 2.88 2.49 2.15 1.85 1.62 1.42
11.19 9.33 8.00 7.00 5.81 4.90 4.04 3.40 2.89 2.50 2.18 1.91
positive position
5.00
0.59
0.59
0.46
0.31
0.79
0.79
0.66
0.44
1.03
1.03
0.82
0.55
1.27
1.27
1.00
0.67
1.82
1.68
1.26
0.84
0.52
0.52
0.39
0.26
0.70
0.70
0.55
0.37
0.92
0.92
0.69
0.46
1.13
1.12
0.84
0.56
1.63
1.42
1.06
0.71
0.47
0.44
0.33
0.22
0.63
0.63
0.47
0.31
0.83
0.79
0.59
0.39
1.01
0.96
0.72
0.48
1.46
1.21
0.90
0.60
0.42
0.38
0.28
0.19
0.57
0.54
0.40
0.27
0.75
0.67
0.51
0.34
0.92
0.82
0.61
0.41
1.32
1.03
0.78
0.52
0.38
0.33
0.25
0.16
0.51
0.46
0.35
0.23
0.68
0.58
0.44
0.29
0.83
0.71
0.53
0.35
1.20
0.89
0.67
0.45
0.35
0.29
0.21
0.14
0.47
0.40
0.30
0.20
0.62
0.51
0.38
0.25
0.76
0.62
0.46
0.31
1.09
0.78
0.58
0.39
0.32
0.25
0.19
0.12
0.43
0.35
0.26
0.18
0.56
0.44
0.33
0.22
0.69
0.54
0.40
0.27
1.00
0.68
0.51
0.34
0.29
0.22
0.16
0.11
0.39
0.31
0.23
0.16
0.52
0.39
0.29
0.20
0.64
0.47
0.36
0.24
0.92
0.60
0.45
0.30
0.27
0.19
0.15
0.10
0.36
0.27
0.21
0.14
0.48
0.35
0.26
0.17
0.59
0.42
0.31
0.21
0.84
0.53
0.40
0.26
0.59
0.79
1.03
1.26
1.69
0.52
0.70
0.92
1.12
1.51
0.47
0.63
0.83
1.01
1.36
0.42
0.57
0.75
0.91
1.22
0.39
0.51
0.68
0.82
1.11
0.35
0.47
0.62
0.75
1.01
0.32
0.43
0.56
0.69
0.93
0.29
0.39
0.52
0.63
0.85
0.27
0.36
0.48
0.58
0.78
5.00
0.71
0.49
0.36
0.24
0.96
0.69
0.52
0.34
1.27
0.86
0.65
0.43
1.58
1.05
0.79
0.53
2.28
1.33
0.99
0.66
0.63
0.41
0.31
0.20
0.86
0.58
0.43
0.29
1.14
0.73
0.55
0.36
1.41
0.89
0.66
0.44
2.03
1.12
0.84
0.56
0.57
0.35
0.26
0.17
0.77
0.49
0.37
0.25
1.02
0.62
0.46
0.31
1.27
0.75
0.56
0.38
1.83
0.95
0.71
0.47
0.51
0.30
0.22
0.15
0.69
0.42
0.32
0.21
0.92
0.53
0.40
0.27
1.14
0.65
0.48
0.32
1.65
0.81
0.61
0.41
0.46
0.26
0.19
0.13
0.63
0.37
0.27
0.18
0.83
0.46
0.34
0.23
1.04
0.56
0.42
0.28
1.49
0.70
0.53
0.35
0.42
0.22
0.17
0.11
0.57
0.32
0.24
0.16
0.76
0.40
0.30
0.20
0.95
0.48
0.36
0.24
1.36
0.61
0.46
0.31
0.39
0.20
0.15
0.10
0.52
0.28
0.21
0.14
0.70
0.35
0.26
0.17
0.87
0.42
0.32
0.21
1.25
0.54
0.40
0.27
0.36
0.17
0.13
0.09
0.48
0.24
0.18
0.12
0.64
0.31
0.23
0.15
0.79
0.37
0.28
0.19
1.14
0.47
0.35
0.24
0.33
0.15
0.11
0.08
0.44
0.22
0.16
0.11
0.59
0.27
0.20
0.14
0.73
0.33
0.25
0.17
1.05
0.42
0.31
0.21
0.59
0.78
1.05
1.29
1.86
0.52
0.71
0.95
1.17
1.69
0.47
0.65
0.87
1.07
1.54
0.42
0.60
0.79
0.98
1.40
0.39
0.55
0.73
0.90
1.29
0.36
0.51
0.67
0.83
1.18
0.33
0.47
0.62
0.76
1.09
0.31
0.43
0.58
0.71
1.01
0.28
0.40
0.53
0.65
0.93
perm. q [kN/m2]
1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 3.20
End supporting with bA = 40 mm, Intermediate supporting with bB 60 mm
6.02 4.71 3.46 2.88 2.52 2.04 1.69 1.42 1.21 1.04 0.91 0.80
6.02 4.71 3.46 2.88 2.52 2.04 1.69 1.38 1.09 0.87 0.71 0.58
6.02 4.71 3.46 2.88 2.46 1.79 1.35 1.04 0.82 0.65 0.53 0.44
6.02 4.71 3.46 2.34 1.64 1.19 0.90 0.69 0.54 0.44 0.35 0.29
8.12 6.30 4.63 3.89 3.42 2.77 2.29 1.93 1.64 1.41 1.23 1.08
8.12 6.30 4.63 3.89 3.42 2.77 2.29 1.93 1.54 1.23 1.00 0.83
8.12 6.30 4.63 3.89 3.42 2.53 1.91 1.47 1.15 0.92 0.75 0.62
8.12 6.30 4.63 3.30 2.32 1.69 1.27 0.98 0.77 0.62 0.50 0.41
10.78 8.28 6.08 5.17 4.54 3.68 3.04 2.56 2.18 1.88 1.64 1.44
10.78 8.28 6.08 5.17 4.54 3.68 3.04 2.46 1.93 1.55 1.26 1.04
10.78 8.28 6.08 5.17 4.37 3.18 2.39 1.84 1.45 1.16 0.94 0.78
10.78 8.28 6.08 4.15 2.91 2.12 1.60 1.23 0.97 0.77 0.63 0.52
13.29 10.10 7.42 6.37 5.65 4.58 3.78 3.18 2.71 2.33 2.03 1.79
13.29 10.10 7.42 6.37 5.65 4.58 3.78 2.99 2.35 1.88 1.53 1.26
13.29 10.10 7.42 6.37 5.31 3.87 2.91 2.24 1.76 1.41 1.15 0.94
13.29 10.10 7.42 5.04 3.54 2.58 1.94 1.49 1.17 0.94 0.76 0.63
19.19 13.60 10.51 9.19 8.14 6.59 5.45 4.58 3.90 3.36 2.93 2.57
19.19 13.60 10.51 9.19 8.14 6.51 4.89 3.77 2.96 2.37 1.93 1.59
19.19 13.60 10.51 9.19 6.69 4.88 3.67 2.83 2.22 1.78 1.45 1.19
19.19 13.60 9.49 6.36 4.46 3.25 2.45 1.88 1.48 1.19 0.96 0.79
End supporting with bA = 40 mm, Intermediate supporting with bB = 0 mm
3.66 3.05 2.62 2.29 2.03 1.70 1.40 1.18 1.00 0.87 0.76 0.66
4.84 4.04 3.46 3.03 2.68 2.27 1.87 1.57 1.34 1.16 1.01 0.89
6.81 5.67 4.86 4.25 3.68 2.98 2.46 2.07 1.76 1.52 1.32 1.16
8.62 7.19 6.16 5.39 4.48 3.64 3.00 2.52 2.15 1.85 1.62 1.43
12.72 10.60 9.09 7.65 6.05 4.89 4.04 3.40 2.94 2.60 2.31 2.07
negative position
Proviled sheet
Negative position
Dimmensions in [mm]
The trapezoidal profile used as a load-bearing building component for roofing and ceiling systems is only
suitable for foot traffic by single persons after load-distributing measures have been taken (e.g., wooden
planks). The laying plans should contain information to this effect.
Line *:
Lines L/:
Permissible load taking account of a limitation of deflection of max f L/... . These values also apply to
the lower part of the tables for two- and three-span girder if they are smaller than those quoted line *.
The tables are not a substitute for the structural analyses required for the building design. The permissible load values
have been determined in accordance with the provisions of DIN 18807.
Observe the maximum length supplied, especially in the case of multiple-span girder.
perm. q [kN/m2]
2.00
1.58
1.58
1.26
0.84
2.21
1.96
1.47
0.98
3.27
2.36
1.77
1.18
4.28
2.73
2.05
1.36
5.39
3.36
2.52
1.68
1.30
1.26
0.95
0.63
1.82
1.47
1.11
0.74
2.70
1.78
1.33
0.89
3.54
2.05
1.54
1.03
4.46
2.52
1.89
1.26
0.39
0.21
0.16
0.11
0.55
0.25
0.18
0.12
0.82
0.30
0.22
0.15
1.07
0.34
0.26
0.17
1.35
0.42
0.32
0.21
1.09
0.97
0.73
0.49
1.53
1.14
0.85
0.57
2.27
1.37
1.03
0.68
2.97
1.58
1.18
0.79
3.75
1.94
1.46
0.97
0.93
0.76
0.57
0.38
1.31
0.89
0.67
0.45
1.94
1.08
0.81
0.54
2.53
1.24
0.93
0.62
3.19
1.53
1.15
0.76
0.80
0.61
0.46
0.31
1.13
0.72
0.54
0.36
1.67
0.86
0.65
0.43
2.18
0.99
0.75
0.50
2.75
1.22
0.92
0.61
0.70
0.50
0.37
0.25
0.98
0.58
0.44
0.29
1.45
0.70
0.53
0.35
1.90
0.81
0.61
0.40
2.40
1.00
0.75
0.50
0.62
0.41
0.31
0.21
0.86
0.48
0.36
0.24
1.28
0.58
0.43
0.29
1.67
0.67
0.50
0.33
2.11
0.82
0.62
0.41
0.55
0.34
0.26
0.17
0.76
0.40
0.30
0.20
1.13
0.48
0.36
0.24
1.48
0.56
0.42
0.28
1.87
0.68
0.51
0.34
0.49
0.29
0.22
0.14
0.68
0.34
0.25
0.17
1.01
0.41
0.30
0.20
1.32
0.47
0.35
0.23
1.66
0.58
0.43
0.29
0.44
0.24
0.18
0.12
0.61
0.29
0.21
0.14
0.91
0.34
0.26
0.17
1.19
0.40
0.30
0.20
1.49
0.49
0.37
0.24
0.36
0.18
0.14
0.09
0.50
0.21
0.16
0.11
0.74
0.26
0.19
0.13
0.97
0.29
0.22
0.15
1.22
0.36
0.27
0.18
0.33
0.16
0.12
0.08
0.46
0.18
0.14
0.09
0.68
0.22
0.17
0.11
0.88
0.26
0.19
0.13
1.11
0.32
0.24
0.16
0.30
0.14
0.10
0.07
0.42
0.16
0.12
0.08
0.62
0.19
0.15
0.10
0.81
0.22
0.17
0.11
1.02
0.28
0.21
0.14
0.27
0.12
0.09
0.06
0.38
0.14
0.11
0.07
0.57
0.17
0.13
0.09
0.74
0.20
0.15
0.10
0.94
0.24
0.18
0.12
0.25
0.11
0.08
0.05
0.35
0.13
0.09
0.06
0.52
0.15
0.11
0.08
0.68
0.17
0.13
0.09
0.86
0.22
0.16
0.11
perm. q [kN/m2]
1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 3.20
End supporting with bA = 40 mm, Intermediate supporting with bB 60 mm
5.88 4.38 3.22 2.77 2.18 1.77 1.46 1.23 1.05 0.90 0.79 0.69
5.88 4.38 3.22 2.77 2.18 1.77 1.46 1.23 1.05 0.90 0.79 0.69
5.88 4.38 3.22 2.77 2.18 1.77 1.46 1.23 1.05 0.90 0.79 0.69
5.88 4.38 3.22 2.77 2.18 1.77 1.46 1.17 0.92 0.74 0.60 0.49
6.89 5.74 4.51 3.45 2.72 2.21 1.82 1.53 1.31 1.13 0.98 0.86
6.89 5.74 4.51 3.45 2.72 2.21 1.82 1.53 1.31 1.13 0.98 0.86
6.89 5.74 4.51 3.45 2.72 2.21 1.82 1.53 1.31 1.13 0.98 0.86
6.89 5.74 4.51 3.45 2.72 2.21 1.77 1.36 1.07 0.86 0.70 0.58
9.49 7.91 6.68 5.11 4.04 3.27 2.71 2.27 1.94 1.67 1.46 1.28
9.49 7.91 6.68 5.11 4.04 3.27 2.71 2.27 1.94 1.67 1.46 1.28
9.49 7.91 6.68 5.11 4.04 3.27 2.71 2.27 1.94 1.55 1.26 1.04
9.49 7.91 6.68 5.11 3.90 2.84 2.14 1.65 1.29 1.04 0.84 0.69
11.95 9.96 8.54 6.69 5.29 4.28 3.54 2.97 2.53 2.18 1.90 1.67
11.95 9.96 8.54 6.69 5.29 4.28 3.54 2.97 2.53 2.18 1.90 1.60
11.95 9.96 8.54 6.69 5.29 4.28 3.54 2.85 2.24 1.79 1.46 1.20
11.95 9.96 8.54 6.41 4.50 3.28 2.47 1.90 1.49 1.20 0.97 0.80
16.89 14.07 11.01 8.43 6.66 5.39 4.46 3.75 3.19 2.75 2.40 2.11
16.89 14.07 11.01 8.43 6.66 5.39 4.46 3.75 3.19 2.75 2.39 1.97
16.89 14.07 11.01 8.43 6.66 5.39 4.46 3.51 2.76 2.21 1.79 1.48
16.89 14.07 11.01 7.88 5.54 4.04 3.04 2.34 1.84 1.47 1.20 0.99
End supporting with bA = 40 mm, Intermediate supporting with bB = 0 mm
3.39 2.82 2.42 2.12 1.79 1.51 1.29 1.09 0.93 0.81 0.70 0.62
5.01 4.17 3.58 3.13 2.58 2.15 1.81 1.53 1.30 1.12 0.98 0.86
6.77 5.64 4.83 4.23 3.50 2.93 2.49 2.14 1.86 1.63 1.44 1.28
8.41 7.01 6.01 5.26 4.37 3.66 3.12 2.69 2.34 2.06 1.82 1.62
12.84 10.70 9.17 8.02 6.59 5.39 4.45 3.74 3.19 2.75 2.39 2.11
negative position
5.00
0.61
0.61
0.61
0.41
0.76
0.76
0.72
0.48
1.13
1.13
0.87
0.58
1.48
1.34
1.00
0.67
1.87
1.64
1.23
0.82
0.55
0.55
0.52
0.35
0.68
0.68
0.61
0.40
1.01
0.98
0.73
0.49
1.32
1.12
0.84
0.56
1.67
1.39
1.04
0.69
0.49
0.49
0.44
0.29
0.61
0.61
0.52
0.34
0.91
0.83
0.62
0.41
1.19
0.96
0.72
0.48
1.49
1.18
0.88
0.59
0.44
0.44
0.38
0.25
0.55
0.55
0.44
0.29
0.82
0.71
0.53
0.36
1.07
0.82
0.61
0.41
1.35
1.01
0.76
0.50
0.40
0.40
0.33
0.22
0.50
0.50
0.38
0.25
0.74
0.61
0.46
0.31
0.97
0.71
0.53
0.35
1.22
0.87
0.65
0.44
0.37
0.37
0.28
0.19
0.46
0.44
0.33
0.22
0.68
0.53
0.40
0.27
0.88
0.62
0.46
0.31
1.11
0.76
0.57
0.38
0.33
0.33
0.25
0.17
0.42
0.39
0.29
0.19
0.62
0.47
0.35
0.23
0.81
0.54
0.40
0.27
1.02
0.66
0.50
0.33
0.31
0.29
0.22
0.15
0.38
0.34
0.26
0.17
0.57
0.41
0.31
0.21
0.74
0.47
0.36
0.24
0.94
0.58
0.44
0.29
0.28
0.26
0.19
0.13
0.35
0.30
0.23
0.15
0.52
0.36
0.27
0.18
0.68
0.42
0.31
0.21
0.86
0.52
0.39
0.26
0.55
0.76
1.13
1.46
1.86
0.49
0.68
1.01
1.32
1.66
0.44
0.61
0.91
1.18
1.49
0.39
0.55
0.82
1.07
1.35
0.36
0.50
0.74
0.97
1.22
0.33
0.46
0.68
0.88
1.11
0.30
0.42
0.62
0.81
1.02
0.27
0.38
0.57
0.74
0.94
0.25
0.35
0.52
0.69
0.86
5.00
0.77
0.65
0.49
0.32
0.93
0.76
0.57
0.38
1.27
0.91
0.68
0.46
1.60
1.05
0.79
0.53
2.25
1.29
0.97
0.65
0.68
0.54
0.41
0.27
0.83
0.64
0.48
0.32
1.14
0.77
0.58
0.38
1.43
0.88
0.66
0.44
2.01
1.09
0.82
0.55
0.61
0.46
0.35
0.23
0.74
0.54
0.41
0.27
1.02
0.65
0.49
0.33
1.28
0.75
0.56
0.38
1.80
0.93
0.70
0.46
0.55
0.40
0.30
0.20
0.67
0.46
0.35
0.23
0.92
0.56
0.42
0.28
1.16
0.65
0.48
0.32
1.63
0.79
0.60
0.40
0.50
0.34
0.26
0.17
0.61
0.40
0.30
0.20
0.83
0.48
0.36
0.24
1.05
0.56
0.42
0.28
1.48
0.69
0.51
0.34
0.46
0.30
0.22
0.15
0.55
0.35
0.26
0.17
0.76
0.42
0.32
0.21
0.96
0.48
0.36
0.24
1.35
0.60
0.45
0.30
0.42
0.26
0.20
0.13
0.51
0.31
0.23
0.15
0.70
0.37
0.28
0.18
0.88
0.42
0.32
0.21
1.23
0.52
0.39
0.26
0.38
0.23
0.17
0.11
0.47
0.27
0.20
0.13
0.64
0.32
0.24
0.16
0.80
0.37
0.28
0.19
1.13
0.46
0.34
0.23
0.35
0.20
0.15
0.10
0.43
0.24
0.18
0.12
0.59
0.29
0.21
0.14
0.74
0.33
0.25
0.17
1.04
0.41
0.31
0.20
0.57
0.78
1.13
1.48
1.96
0.52
0.70
1.01
1.32
1.76
0.47
0.64
0.91
1.19
1.59
0.43
0.58
0.82
1.07
1.45
0.40
0.53
0.74
0.97
1.32
0.37
0.48
0.68
0.88
1.21
0.34
0.45
0.63
0.81
1.11
0.31
0.41
0.58
0.74
1.02
0.29
0.38
0.54
0.68
0.94
perm. q [kN/m2]
1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 3.20
End supporting with bA = 40 mm, Intermediate supporting with bB 60 mm
6.30 4.38 3.66 3.20 2.73 2.21 1.83 1.54 1.31 1.13 0.98 0.86
6.30 4.38 3.66 3.20 2.73 2.21 1.83 1.54 1.31 1.13 0.94 0.78
6.30 4.38 3.66 3.20 2.73 2.21 1.79 1.38 1.09 0.87 0.71 0.58
6.30 4.38 3.66 3.11 2.18 1.59 1.19 0.92 0.72 0.58 0.47 0.39
7.83 6.13 4.50 3.75 3.31 2.68 2.22 1.86 1.59 1.37 1.19 1.05
7.83 6.13 4.50 3.75 3.31 2.68 2.22 1.86 1.59 1.35 1.10 0.91
7.83 6.13 4.50 3.75 3.31 2.68 2.09 1.61 1.27 1.02 0.82 0.68
7.83 6.13 4.50 3.63 2.54 1.85 1.39 1.07 0.84 0.68 0.55 0.45
10.78 8.98 6.68 5.17 4.54 3.68 3.04 2.56 2.18 1.88 1.64 1.44
10.78 8.98 6.68 5.17 4.54 3.68 3.04 2.56 2.04 1.63 1.33 1.09
10.78 8.98 6.68 5.17 4.54 3.36 2.52 1.94 1.53 1.22 0.99 0.82
10.78 8.98 6.52 4.37 3.07 2.24 1.68 1.29 1.02 0.82 0.66 0.55
13.58 11.32 8.74 6.68 5.72 4.64 3.83 3.22 2.74 2.37 2.06 1.81
13.58 11.32 8.74 6.68 5.72 4.64 3.83 2.99 2.35 1.88 1.53 1.26
13.58 11.32 8.74 6.68 5.31 3.87 2.91 2.24 1.76 1.41 1.15 0.94
13.58 11.32 7.52 5.04 3.54 2.58 1.94 1.49 1.17 0.94 0.76 0.63
19.19 14.98 11.01 9.19 8.04 6.52 5.38 4.52 3.86 3.32 2.90 2.55
19.19 14.98 11.01 9.19 8.04 6.35 4.78 3.68 2.89 2.32 1.88 1.55
19.19 14.98 11.01 9.19 6.54 4.76 3.58 2.76 2.17 1.74 1.41 1.16
19.19 14.71 9.26 6.21 4.36 3.18 2.39 1.84 1.45 1.16 0.94 0.78
End supporting with bA = 40 mm, Intermediate supporting with bB = 0 mm
3.85 3.21 2.75 2.41 1.95 1.57 1.30 1.09 0.93 0.80 0.71 0.64
5.69 4.74 4.07 3.45 2.72 2.21 1.82 1.53 1.31 1.13 0.98 0.87
7.69 6.41 5.49 4.81 4.04 3.27 2.71 2.27 1.94 1.67 1.45 1.28
9.56 7.97 6.83 5.97 5.28 4.28 3.54 2.97 2.53 2.18 1.90 1.67
14.59 12.16 10.42 8.43 6.66 5.39 4.46 3.74 3.20 2.80 2.47 2.19
All details contained in this brochure are only guaranteed insofar as they have been expressly
and specifically confirmed in writing. Subject to technical modifications.
GB Info 4.3.4 8.2007 bc