Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Introduction
Limiting self-weight is a primary requirement in the design of most types of bridges. Self-weight is among
the most significant loads on the bridge and its reduction creates a reserve available for live loads. Selfweight also governs the cost of construction equipment, which is a prime component of the construction
cost of a bridge (1). The density of normal-weight concrete does not vary much with the concrete
strength, the weight of a prestressed-concrete (PC) bridge depends linearly on the cross-sectional area,
and the most influencing parameters are therefore related to the cross-sectional geometry.
The influence of the different parameters has been analyzed with a database of 165 constant-depth PC
box-girder highway bridges with continuous spans ranging from 19m to 96m. The depth of the crosssection governs the shear and flexural capacity and therefore increases regularly with the span, Figure 1.
The cost of materials and specialized
construction equipment (1) depends on the
weight of the cross-section, i.e. on its area
A. The moment of inertia I is the main
indicator of the flexural capacity of the
cross-section (2,3,4) and is inversely
proportional to the cost of post-tensioning
(4). The design efficiency of a PC bridge can
therefore be evaluated in terms of radius of
gyration of the cross-section
depth (m)
4.0
2.0
0.0
10
40
70
span (m)
I
A
(1)
100
1.5
1.0
0.5
0.0
10
40
70
span (m)
100
2
rmax
zu zl
(2)
1|3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
r2
I
1
2
rmax zu zl A
(3)
The closer f is to the ideal value of 1, the better the flexural efficiency, and the lower the quantity of
post-tensioning. The flexural efficiency of the PC bridges in the database is shown in Figure 3.
The cross-section of a PC box girder includes top slab, bottom slab and webs, and these three
components can be treated separately to increase the flexural efficiency f . The thickness of the top
slab depends on localized wheel-load bending and on the need for punching strength and adequate
concrete cover, and cannot be reduced excessively. The thickness of the bottom slab is often governed by
technological requirements of internal post-tensioning, but its design is generally less restrained. Using
internal post-tensioning, the web thickness is often governed by the need to contain and deviate the
tendons, and in a narrow box girder the
Figure 3: Flexural efficiency vs. span length
webs can reach 30% of the cross-sectional
area (5).
flexural efficiency
1.0
0.8
0.6
0.4
0.2
10
40
70
100
span (m)
The efficiency of a material can be evaluated with its strength-to-density ratio, em f . A concrete
with compressive strength fc ' 45N mm2 and density c 25kN m3 has compressive efficiency
2
em 1.8 103m and much smaller tensile efficiency. A steel plate with yielding strength fy 355N mm
and density s 77kN m3 has tensile efficiency em 4.6 103 m at first yielding and is 2.5 times more
efficient than concrete in optimum work conditions. The composite bridges with concrete slab and steel
girders are therefore more efficient than the PC bridges, as their masses are more distant from the
gravity axis, and the materials perform better.
Prestressing strand, however, is definitely more efficient. Commercial 7-wire strand reaches
em 21.5103 m at the 0.1%-load, and a cable is generally the most effective way to use steel in tension.
By relating the efficiency of materials in their optimal work conditions to the efficiency of prestressing
steel, 45MPa concrete reaches 8.4%, and medium-grade steel plates reach 21.4%.
A PC bridge is mainly designed for bending (4). Prestressing is the most efficient and cost-effective solution
to control the edge tensile stresses generated by the bending moment, and in a continuous beam this
requires the presence of two flanges to compress without instability. The use of reinforced concrete for
the two flanges offers compressive strength at low cost, and the use of external post-tensioning allows
web design for principal stresses without geometry restraints. Once the flexural demand has been met,
tendon deviation reduces the tangential stresses in the webs, with beneficial effects on web thickness
and the flexural efficiency of the cross-section.
2|3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
The efficiency of concrete can be improved by increasing the strength with the same density (i.e., by
using high-performance concrete) or by reducing the density with the same strength (i.e., by using
lightweight concrete). The next step in the research of maximum flexural efficiency consists in
abandoning the concrete webs and using two or more steel I-girders to connect the concrete slabs. Steel
webs offer the same shear capacity as concrete webs with only 5-8% of their weight, tendon deviation
diminishes the shear demand on the webs, the flexural efficiency of the cross-section increases because
of a better mass distribution, and these sections are also fast and easy to build.
3|3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
A prestressed composite box girder with steel-plate webs is a hybrid between a PC box girder and a nonprestressed steel-composite deck that takes the best from the two technologies. Compared with a nonprestressed composite deck with two or multiple I-girders, the webs are thinner, the flanges are smaller,
less cross frames and no lateral braces are necessary, the weight of steelwork is only 15-20%, the unit
cost of steelwork is similar, field assembly is simpler, the geometry tolerances are less stringent, and the
maintenance costs are lower. Compared with a PC box girder, the absence of concrete webs saves labor
and post-tensioning and accelerates construction, reinforcement is simpler and easier to fabricate, and
casting cell and erection equipment (1) are less expensive.
flexural efficiency
The flexural efficiency of prestressed composite box girders with steel-plate webs has been evaluated by
subtracting the concrete webs from the cross-sectional area and moment of inertia of the bridge
database, and by increasing the net area thus determined by 5% to account for the weight of the steel
webs. The results are represented with
Figure 5: Flexural efficiency vs. span length
black dots, Figure 5, while the grey dots
represent the data in Figure 3. The increase
1.0
in flexural efficiency is substantial, and the
result is particularly interesting on longer
0.8
spans because of the progressive increase
in the web depth with the span. Better
0.6
structural performance and savings in
labor, concrete, reinforcement,
0.4
prestressing and construction equipment
balance the cost of steel webs and the risks
0.2
10
40
70
100
of innovation, and open new perspectives
in the design and construction of mediumspan (m)
span bridges.
The most intuitive way to replace the concrete webs of a PC box girder with steel webs is the use of
stiffened-plate webs. The deck has a conventional aspect, as the prestressing tendons are hidden within
the box cell. The behavior of the individual materials is well known, and the combined use of reinforced
concrete slabs and steel I-girders has been amply tested in hundreds of composite bridges. However, this
simplicity is only apparent, and several reasons discourage the use of this structural solution.
The steel webs resist a significant portion of the prestressing force applied to the composite section.
Under an axial force F, strain compatibility at the web-slab nodes governs the distribution of the axial
force between the concrete slabs, of total area Ac , and the steel girders, of total area As . The initial
portion of post-tensioning resisted by the steel girders is
Fs
As
F
E
As c Ac
Es
(4)
where Ec is the elastic modulus of concrete at stressing. The effects of concrete creep can be evaluated
with an age-adjusted modulus that decreases with time, and therefore Fs increases with time and soon
reaches 20-25% of the total prestressing force. This force is wasted and requires additional stiffeners to
prevent web buckling, which increases the fabrication cost of the webs and may reduce their fatigue life
due to cracks initiating at the stiffener welds (9).
If the webs were devoid of axial stiffness, the webs would resist only shear force, and the concrete slabs
would resist the entire bending. The axial stiffness of the webs must therefore be diminished without
affecting their shear capacity, and this requires anisotropic behavior. Orthotropic plates with different
4|3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
stiffness in the orthogonal directions are commonly used in steel bridges. Webs and bottom flange of
steel box girders are heavily stiffened in the direction of the principal compressive stresses, and less
stiffened in the orthogonal direction. This concept may be extended to the axial stiffness of a plate by
folding the plate to reduce its capability of resisting axial stress without affecting the shear capacity.
Trapezoidally- or sinusoidally-corrugated steel or aluminum plates are commonly accepted in naval and
aeronautical applications (10). Several fuselages and wing structures have been built with undulated or
corrugated plates. Skins of F-15 and wings of AV-8B and F-22 adopt corrugated panels (11). Aircraft
designers have realized long ago that the corrugated panels have larger buckling strength in the direction
perpendicular to the corrugation. Corrugated metal panels have long been recognized as excellent shear
carrying members. This is attributed to two characteristics of the panels: the transverse stiffness provided
by the corrugation depth, and the in-plane stiffness due to narrow spaced folds that act as vertical
stiffeners (12,13).
In civil structures, the advantages of structural anisotropy may be exploited by replacing the stiffenedplate webs of steel or composite girders with corrugated-plate webs (14,15,16,17). Vertical corrugation by cold
folding creates the in-plane flexibility necessary to minimize the longitudinal axial capacity of the web
panels, and amplifies the transverse flexural capacity needed to resist transverse bending and crosssectional distortion and to prevent buckling of web panels devoid of welded stiffeners, Figure 6.
Figure 6: Corrugated-plate webs (photo: Doka)
The idea of using corrugated-plate webs in civil structures was first introduced for the steel beams of
buildings, where the web thickness varies from 2mm to 5mm, and the height-to-thickness ratio of the web
panels varies between 150 and 260 (18). In the past three decades there has been increasing interest in
prestressed composite box-girder bridges with steel corrugated-plate webs, where the web thickness
varies between 8mm and 12mm, and the height-to-thickness ratio of the web panels typically ranges
between 220 and 375, and has reached 445.
The corrugated-plate webs have symmetrical regular shape with constant wavelength in the longitudinal
direction. Load tests on specimens of corrugated plates, finite-element numerical analyses and studies on
the behavior of corrugated-plate webs in prestressed composite bridges have been conducted in Britain,
Canada, China, Egypt, France, Germany, Hungary, Italy, Japan, Sweden and the USA, and the first actual
5|3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
bridges confirmed many advantages of the prestressed composite box girders with steel corrugated-plate
webs over the stiffened-plate ones (19,9,2).
The longitudinal flexibility of the webs minimizes the initial and time-dependent loss of prestress
into the webs. Fewer tendons are needed to prestress the slabs, and fewer shear connectors are
needed at the web flanges to transfer longitudinal interface shear. Internal tendons in a slab
compress only that slab and do not affect the other slab.
The state of stress in the central region of the web panels is an almost pure shear one. The
thickness of the web plates is chosen for shear strength, and the corrugation is designed to
control buckling. The webs may often be made with 8mm plates, while stiffened-plate webs are
rarely thinner than 12mm. In addition to savings in weight, this opens new perspectives for the
efficient use of high-grade steels.
Shear is mostly carried by tendon deviation, the residual shear is carried by the webs, bending is
carried by the concrete slabs, torsion is carried with hollow-section behavior, resistance to crosssectional distortion (20) is higher and more uniform throughout the length of the bridge, and the
interaction between bending and shear is minimal. Every material works with optimal stress
distribution.
The transverse stiffness of the corrugated plates avoids the need for welded stiffeners, reduces
the number of cross frames and diaphragms within the box cell, and saves material and labor.
These savings, along with the reduced plate thickness, are often enough to cover the cost of plate
corrugation.
Higher transverse stiffness, closely spaced folds, and the boundary restraint provided by the
concrete slabs increase web stability from buckling. Buckling depends on shear only, while in a
stiffened-plate web it depends on combined shear and axial stresses. Longitudinal axial stresses
do arise in the corrugated-plate webs in proximity of the concrete slabs, and vertical axial stresses
arise in the support regions of the bridge; these local stresses, however, do not affect web
stability.
The sensitivity to premature buckling due to geometry defects is definitely lower. The defects of
planarity are compared with the amplitude of the folds instead of the plate thickness, and their
effects are 10-20 times lower. Local distortion due to welding is limited to the edges of the
panels, which are restrained by the concrete slabs. The plastic strains due to cold folding are
uniform over the web depth and do not affect the elastic equilibrium of the panel.
The flexibility of the web panels facilitates fabrication and field assembly and avoids the need for
trial assembly and tight geometry tolerances. The web panels are overlapped and fillet-welded on
either side; in-place casting of the concrete slabs compensates for the residual geometry
irregularities.
Prestressed composite box-girder bridges with corrugated-plate webs have been built by incremental
launching on 40-55m spans and as balanced cantilevers on longer spans, Figure 6. Corrugated-plate webs
have been used in extradosed and cable-stayed bridges, and research is in progress to extend their use to
long-span arches. Combined with the use of high-performance concrete for the rib slabs, corrugated-plate
webs could lighten the arch ribs, diminish the cost of foundations and temporary support systems prior to
crown closure, avoid labor-intensive staged casting of concrete webs, and accelerate construction.
6|3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
The restraint that the concrete slabs exert on the horizontal flexural deformations of the web plates
depends on the width and thickness of the steel flanges, on the effective width and thickness of the
concrete slabs, and on the reinforcement ratio of the latter. All these parameters influence the stress
distribution within the cross-section.
a f b f tw
c f 3b f h f
Es
(5)
The benefit of formulating an effective longitudinal modulus is that analysis methods for flat plates can
be applied to the solution of problems of corrugated panels. The corrugation angle is typically between
30 and 32, although actual bridge applications range from 25 to 38. For a typical web panel with
tw 8mm , bf c f 300mm and corrugation angle 30 , the effective longitudinal modulus is
E x ,eff 0.0013 E s , i.e. three orders of magnitude smaller than E s . This reduction in the axial stiffness
governs the axial stress distribution within the composite cross-section: the webs resist minimal
longitudinal bending, and in the absence of prestressing, two equal and opposite axial forces in the
concrete slabs balance the external moment (23).
Marco Rosignoli, Dr.Ing., PE | Bridge Engineering eManuals All Rights Reserved
7|3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
For the same reason, a prestressing force applied to a slab remains within the slab and does not affect the
webs and the other slab. Finite-element analysis and load tests showed that corrugated-plate webs
absorb a minimal fraction of the prestressing force applied to the cross-section, and the axial forces in the
slabs can be calculated based on the geometry of a cross-section composed of concrete slabs only.
Because of plate corrugation, the axial deformations of the slabs generate horizontal bending in the folds.
The peak horizontal bending generated at a vertical fold line by a longitudinal axial stress c in the
concrete slabs is (24)
mz
bf a f
Es
tw3
c
3b f c f 72h f Ec 1 2
(6)
After corrugation, the web plates are welded to flange plates, which are ultimately connected to the
concrete slabs. Strain compatibility generates longitudinal axial stress in the web regions close to the
flanges; the axial stress is higher in the longitudinal folds than in the inclined folds. With the typical
dimensions of the web plates for box-girder bridges, the longitudinal axial stress fades rapidly in 10-15%
of the panel depth and is negligible in the central 70-80% region of the panel (24). The local axial stress due
to shrinkage of concrete, slab shortening at the application of prestress and over time, live loads and
thermal gradients is the smaller the more constant the web corrugation is.
The longitudinal axial stress at the edges of the web panels does not seem to cause fatigue, as indicated
by the rarity of problems at the web-slab nodes of non-prestressed composite bridges (25,26). Tests
performed on corrugated plates welded to the flanges by intermittent welds showed that the strength of
the connection is critical for stable shear transfer. Intermittent welding may overload the welds and
cause premature failure, and is not recommended. Tests performed on corrugated plates continuously
welded to the flanges on one side only did not show premature weld failure.
The transverse restraint exerted by the flanges generates transverse bending in the vertical direction,
which fades within 10-15% of the panel depth because of the progressive onset of unrestrained
horizontal bending related to the axial flexibility of the plate. The peak vertical bending at the web-flange
weld is higher than the peak horizontal bending at the folds.
Tangential stress
As in a conventional PC box girder, the webs resist most of the shear. The shear force V applied to each
web can be assumed as uniformly distributed over the web depth, so that the uniform tangential stress is
V tw hw , where tw is the plate thickness and hw is the web depth measured clear between flanges.
Since also the vertical axial stress z is negligible far from the support regions of the bridge, the state of
stress in the web panels is one of pure shear. The two principal stresses 1 and 2 are inclined
at 45, two inclined forces F1 1tw and F2 2tw balance one another longitudinally along the vertical
fold, and the vertical resultant Fz 1tw 2 resists the external shear force (27). In the transverse plane,
the outward push of the compression fiber is balanced by the inward pull of the tension fiber.
The flange plates do not contribute much to the flexural capacity of the composite section and are
designed to be as small as possible. Web corrugation widens the flanges, their thickness is reduced to a
minimum, and the shear connectors are closely spaced to restrain the compression flange and avoid local
buckling. With the symbols in Figure 7, the ratio w of the initial plate length to its final length after
corrugation is
8|3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
bf c f
bf a f
(7)
The average shear angle in a several-wavelength web panel under pure shear is Geff , where the
effective shear modulus (22) is Geff Gs w . For a typical web panel with tw 8mm , bf c f 300mm and
corrugation angle 30 , the effective shear modulus is Geff 0.933Gs , the effective longitudinal
modulus is E x ,eff 0.0013 E s , and the reduction in the longitudinal axial stiffness is two orders of
magnitude larger than the reduction in the shear stiffness. The corrugated-plate webs are slightly more
flexible in shear than the stiffened-plate webs because of w 1 and the use of thinner plates, but the
total shear deflection is still small when compared to the flexural deflection of the composite section, as
deviation forces of polygonal tendons balance most of the vertical shear.
Load tests and finite-element analysis (19) showed that the reduction in Gs obtained by replacing a
stiffened-plate web with a corrugated-plate web corresponds to the value of w . Finite-element analysis
also showed that the shear force resisted by the concrete slabs is negligible in most of the deck but
increases near discontinuities of the shear force (2,4).
In correspondence with a discontinuity V in the shear force, the tangential stress discontinuity
tends to deform the web as a lozenge, i.e. to produce a sudden angular discontinuity Geff in
the web. The flexural and shear stiffness of the concrete slabs opposes sudden angular discontinuities in
the webs, and local systems of vertical
Figure 8: Web-slab interaction at shear discontinuities
forces arise at the web-slab nodes to
transfer the shear forces necessary to bend
the slabs until a common curvature is
reached, Figure 8. These local forces may
require additional connectors and slab
reinforcement; finite-element analysis
helps in investigating the local stresses in
web panels, web-slab nodes and the slabs
as well as in validating approximated
methods for their calculation.
Different shear deformations of slabs and
webs occur at the application points of
localized vertical loads such as support
reactions and tendon deviation forces. Different shear deformations occur in the support regions of nonprestressed composite bridges as well, but the web plates are thicker, and V is due to superimposed
dead and live loads only (self-weight is not resisted with composite action). The vertical axial stresses at
the web-slab interface depend inversely on the square root of the web area, and are therefore higher in
thinner webs.
The assumption that plane sections remain plane is not realistic in the prestressed composite box girders
with steel corrugated-plate webs. It may be adopted for preliminary design and to analyze longitudinal
bending and shear in the continuous beam; stress analysis in the shear discontinuity regions, however,
requires more refined approaches.
9|3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
Torsion-distortion interaction
In a PC box girder, the effects of eccentric loads deviate from Saint-Venants theory of torsion, and the
cross-sectional deformation is a combination of rigid torsional rotation and distortion. These effects
depend respectively on the torsional stiffness of the cross-section, which limits its capacity to rotate about
its axis, and on the interaction between the frame stiffness of the cross-section and the in-plane flexural
stiffness of webs and slabs, which together oppose distortion (20). In most practical cases, pier diaphragms
control distortion at the support sections, tendon deviators stiffen the cross-section along the span, and
warping is disregarded under the assumption that plane sections remain plane.
The distortion of a prestressed composite box girder with steel corrugated-plate webs under eccentric
loads is conceptually similar, but the effects are pronounced by the smaller in- and out-of-plane flexural
stiffness of the webs. The transverse flexural stiffness of corrugated-plate webs is much smaller than the
stiffness of the concrete slabs, the cross-section distorts as a parallelogram hinged at the web-slab nodes,
and control of distortion by in-plane frame action is minimal. The webs are also designed to not resist inplane bending, and distortion is primarily resisted by lateral deflections of the concrete slabs. Pier
diaphragms, tendon deviators and auxiliary cross frames within the box cell are therefore designed to
stabilize the cross-sectional geometry.
To study distortion, a load F applied to the top slab eccentrically from bridge centerline can be
decomposed into two symmetrical loads
F 2 and two anti-symmetrical loads Fh ,
Figure 9: Cross-section symbols
equal in value and opposite in sign, applied
to the top web-slab nodes of the crosssection. Symmetrical loads cause
longitudinal bending and shear. Because of
the minimal frame stiffness of the crosssection, external forces are only
counteracted by shear forces in the webs.
The shear force produced by Fh in each
web, assumed as hinged to the concrete slabs and with the symbols of Figure 9, is Vw Fhc h . This force
is higher than the shear force produced by a torsional moment T Fha , and corresponds to the shear
force due to a moment T Fh a b .
In a box girder with vertical corrugated-plate webs, the torsional shear in the webs is twice the torsional
shear determined with the Saint-Venants theory of torsion for an undeformable cross-section. In a
trapezoidal box girder, the lateral force in the top slab can be obtained (28) by adding a force Vt Fha h to
the shear force resulting from the torsional moment, and the lateral force in the bottom slab can be
obtained by adding a force equal to Vb Fhb h .
As a result of torsion-distortion interaction, the cross-section is subject to a rigid in-plane rotation due to
the torsional moment, and to lateral deflections of the concrete slabs in the opposite directions due to
distortion. Diaphragms and cross frames are therefore necessary to control lateral displacements and
rotations in the concrete slabs, slab edge decompression, and transverse bending in the corrugated-plate
webs (3,4). Although the transverse flexural stiffness generated by plate corrugation is relatively low, the
folds are shallow and the transverse axial stress in the web regions close to the slabs may reach the yield
point of steel at the plate surface. Transverse bending propagates to the web-slab nodes and may require
additional flange connectors and slab reinforcement, especially in the bottom slab.
10 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
Because of the fundamental role of external post-tensioning in reducing the shear force applied to the
webs, the tendon deviators are distributed for optimal control of shear, and distortion is controlled with
additional diaphragms or cross frames. An analysis method proposed for the effects of launch bearing
misalignment in incrementally launched bridges (2,3,4,20) can be easily adapted to the study of the warping
stresses in the cross-section based on the effective longitudinal modulus, equation (5), and the restraint
provided by pier diaphragms, tendon deviators and cross frames to the lateral deflections of the concrete
slabs.
Web-slab nodes
The bottom web-slab node involves a few design challenges to assure durability. Longitudinal corrosion
lines have been frequently observed at the deck paving level in U-spans with edge girders connected by a
concrete slab at the bottom flanges. In a prestressed composite box girder the situation is similar,
although only condensation water can gather within the box cell. Corrosion prevention discourages from
placing triple contact points (air, concrete, and steel) near main structural members. Therefore, while the
top web-slab nodes may be detailed with conventional criteria, the bottom nodes present specific design
challenges, Figure 10.
The simplest solution (Scheme A) consists of casting the bottom slab over the bottom flange and is
adversely affected by a triple contact point on a main structural member. A longitudinal stiffener may be
welded to the web at the top of the slab
Figure 10: Bottom web-slab node
(Scheme B) to move the triple contact
away from the web. In both cases, the field
splices in the bottom flange interfere with
construction by incremental launching
(2,3,4). The slab may also be cast under the
bottom flange (Scheme C). This moves the
triple contact point away from the web,
reduces the weight of steelwork, and offers
a better aesthetic result; however,
embedded props are necessary to support
the web panels on the soffit form prior to
casting of the bottom slab. Concrete
pouring and vibration may be simplified by inclining the webs (Scheme D), which also assures better
concrete adhesion to the bottom flange and better performance of shear connectors. Additional cost
savings derive from a narrower bottom slab.
The web-slab nodes are designed for transfer of longitudinal interface shear, transverse bending and
vertical axial loads in the deck regions subject to shear discontinuities. Headed stud connectors may be
used when the concrete slab is cast over the bottom flange; the connectors for suspended slabs must
also resist the weight of the slab and are therefore embedded more deeply into concrete (29,30,31).
The web-slab connections of prestressed composite box girders are subject to specific design
requirements. The corrugated-plate webs are workshop welded to the flange plates and painted prior to
delivery. The concrete slabs generate the flexural capacity of the composite section, and the steel flanges
have therefore minimal area, for economic reasons and to minimize the restraint exerted on the axial
deformations of the concrete slabs.
Wide flange plates are necessary to accommodate the web corrugation and to contain concrete during
slab casting. The plate thickness is reduced to a minimum, and vertical buckling of the compression flange
11 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
into the web (9) caused premature failure of tested specimens. The shear connectors are therefore
designed for diffused load transfer and to control buckling of the compression flange.
The connectors transfer longitudinal interface shear, vertical axial force, and biaxial bending. Weight of
suspended bottom slab and vertical forces at the longitudinal shear discontinuities in the box girder tend
to detach the slabs from the webs. Cross-sectional frame action and the restraint exerted by the webs on
lateral slab deflections when the cross-section distorts cause transverse bending at the interface. In-plane
lateral deflections of the slabs cause bending about the vertical axis. These effects are more pronounced
at the bottom web-slab node because of the higher lateral flexibility of the bottom slab (4).
Connectors are designed with conventional criteria. Interface shear transfer depends on the residual
shear force, which depends on prestress deviation. Prestressing may be internal in the slabs, external
within the box cell, or a combination of the two. The most effective design approach is balancing the
shear force due to permanent loads and one-half of live loads with the deviation of polygonal tendons, so
that shear forces in the webs and interface shear transfer at the web-slab nodes are only related to the
presence or absence of live loads (27).
In incrementally launched bridges, the integrative post-tensioning applied at the end of launch (2,3,4) is
designed to force the state of stress in the box girder under permanent loads toward an axial
compression one. A prestressed composite
Figure 11: Inner view of box cell
box girder is more flexible than a PC deck,
incremental launching construction
discourages from the application of
cambers, and high degrees of
compensation for the final prestressing (32)
are also necessary for control of midspan
deflections. External polygonal tendons can
be used as the only form of post-tensioning
or can be combined with internal tendons
in the slabs. Additional prestress may be
needed to control the edge stresses and to
provide ultimate flexural capacity. Internal
midspan tendons in the bottom slab and cap tendons over the piers are more efficient than short
external tendons because of the larger eccentricity, smaller anchor blisters, and less tendon congestion
within the box cell. Varying prestressing in the slabs does not cause hyperstatic effects, as the
prestressing forces applied to a slab do not migrate toward the webs and the other slab.
Even when only a few polygonal tendons are used, the shear reduction is significant and longitudinal
interface shear transfer at the web-slab nodes is rarely a major design issue. Most design standards for
composite bridges specify the maximum spacing of flange connectors in relation to slab and flange
thickness and height of connectors. Tight spacing is typically specified for headed stud connectors on 1012 mm flange plates for better control of buckling in the flange regions far from connectors. Headed stud
connectors, therefore, are not much fit for use on thin flange plates, as tight spacing conflicts with slab
reinforcement and prevents the concrete from flowing during slab casting.
Shape connectors (L-connectors with through bars that transfer vertical tensile force and transverse
bending, or channel connectors) are more practical, stabilize the flange plate more effectively, and
facilitate supporting the web panels on the soffit form before casting of the bottom slab. Shape
connectors are workshop welded to the flange in correspondence with the web folds to stiffen the flange
and to prevent buckling at the application of post-tensioning. The longitudinal spacing of shape
12 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
connectors ( a f and b f alternate, as in Figure 7) varies between 250mm and 400mm, with smaller values
near the support sections of the deck.
Some design standards limit the dimensions of the welds of shape connectors to flange in relation to the
plate thickness. The minimum distance between the ends of shape connectors and the edges of the flange
plate is sometimes limited to 25mm. When the top flange is wide to facilitate the operations of a rolling
form table for the concrete slab, Figure 11, the width of shape connectors should not exceed the depth of
the web folds much. Because of combined geometry requirements, thin flange plates suggest combining
regularly-spaced shape connectors with integrative headed stud connectors. Some design standards
specify a reduced shear capacity for headed stud connectors subject to axial tension, and most design
standards specify the nominal shear capacity of L-shapes with hoops and channels.
applicable design standards for shear failure is used to determine the design tangential stress at yielding,
y ,d s y .
The stiffened-plate webs of non-prestressed composite bridges are often designed to meet stability rather
than strength criteria (33,34). When different buckling modes are possible, each mode is identified based on
its critical tangential stress cr ,i . The design value for the critical tangential stress is then determined
based on the resistance factor cr ,i 1 specified by the applicable design standards for that mode,
cr ,i ,d cr ,i cr ,i , and the smallest of the factored design values identifies the design critical tangential
Local buckling
Local buckling corresponds to the shear instability of a flat web sub-panel supported at two vertical folds.
Local buckling affects trapezoidal and zigzag corrugations, while sinusoidal corrugations are unaffected.
The corrugated plate acts as a series of flat unstiffened sub-panels with large aspect ratio ( 6 hw bf 16
in practical cases) that support one another at the folds and are restrained at the flanges. In a prestressed
13 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
composite box girder, the restraint exerted by the flanges corresponds to fixity due to the relative
stiffness of the concrete slabs.
Buckling in a single sub-panel is considered as the failure mode for local buckling. Local buckling is
reversible and preponderant in webs with coarse corrugation, does not cause significant risks of general
instability, and has a post-critical domain. Local buckling in a sub-panel is similar to buckling in a stiffened
plate and can be studied with the classical equations for isotropic plates. Because of the dense
corrugation profile, the corrugated-plate webs are typically stiffer than the traditional stiffened-plate
webs, and their resistance to local buckling is therefore higher.
The elastic critical tangential stress for local buckling of a sub-panel fixed at the edges and with infinite
length ( hw bf 6 ) may be defined with the Timoshenkos theory of stationary potential energy (35)
t
T 4.826E s w
bf
(8)
In equation (8), the longitudinal width b f of the sub-panel is replaced with the inclined width c f if
bigger. The vertical folds provide a flexible restraint to the sub-panels, and the elastic critical tangential
stress for local buckling is therefore lower than the Timoshenkos formulation. The following equation
has been proposed to account for the lower level of edge restraint (36)
tw
bf
cr ,l 0.88 T 4.247E s
(9)
Nonlinear finite-element analysis and tests on specimens of corrugated plates led to a second equation
for the elastic critical tangential stress for local buckling, which includes the effects of the aspect ratio of
the corrugation (9,37)
cr ,l
t
0.904kcr ,l E s w
bf
(10)
The buckling coefficient kcr ,l for local buckling is a function of the aspect ratio hw bf of the sub-panel
and of the support conditions at the boundaries. For simple support at the vertical folds and fixity at the
flanges it is
b
b
3.44 f 8.39 f
hw
hw
hw
bf
(11)
kcr ,l
b
8.98 5.60 f
hw
(12)
The average of the critical tangential stresses calculated with simple support and fixity at the vertical
folds has been found to closely match the results of finite-element analysis (9). The local buckling strength
of the corrugated plate depends on the aspect ratio of the sub-panels and on the plate thickness, and is
independent of the corrugation profile. Finite-element analysis tends to overestimate the results of load
tests because of geometry imperfections in the corrugated plates. Inelastic local buckling may occur
when cr ,l 0.8 y , and the inelastic critical tangential stress can be calculated as
cr ,l ,in 0.9 cr ,l y
(13)
14 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
This semi-empirical equation (38) includes the effects of geometry imperfections and residual stresses
related to plate corrugation and welding to flanges (39,9).
Global buckling
In the global buckling mode, shear instability is characterized by diagonal buckling over several
corrugation sub-panels (18). This mode of instability is critical in webs with dense corrugation, or when a
small corrugation angle results in shallow folds.
The regular, wide wavelength deformation is progressive in the onset and development if in absence of
local buckling, and is similar to that of an orthotropic plate. If local buckling occurs in the post-critical
domain, the corrugated plate may lose the stability necessary to reach shear yielding. Easley (40)
investigated global buckling of corrugated-plate panels with orthotropic-plate buckling theory and tests
on 0.4mm aluminum plates. Tests on steel plates carried out in France (23), the UK (19) and the USA (9)
confirmed Easleys results.
The elastic critical tangential stress for global buckling is determined with the Ritz method (40,41,42) by
considering the corrugated plate as an orthotropic plate with a thickness equal to the corrugation depth
hf
cr ,g kcr ,g
Dz0.25Dx0.75
tw hw2
(14)
The web corrugation profile acts as uniform stiffening in the transverse direction of the panel. The
transverse flexural stiffness of a unit length of corrugated plate with trapezoidal profile is
Dx E stw h2f
3b f c f
12 a f b f
(15)
Dx E stw h2f
cf
12 a f
(16)
For the same sub-panel width and corrugation angle, the trapezoidal corrugation has higher resistance to
global buckling than the zigzag corrugation because of the increased moment of inertia contributed by
the sub-panels parallel to the girder length. The longitudinal flexural stiffness is reduced by the
corrugation ratio w , equation (7), for both types of corrugation
Dz 0.092 E s
tw3
(17)
The buckling coefficient kcr ,g for global buckling solely depends on the restraint exerted by the flanges
and varies from 36.0 for simple support to 68.4 for fixity according to Easley (43), from 31.6 for simple
support to 59.2 for fixity according to Elgaaly (9), and from 32.4 for flexible steel flanges to 60.4 for stiff
concrete slabs according to Bergfeld (44). Simple support at the flanges neglects the restraint to warping
exerted by the concrete slabs (45). Finite-element analysis showed that the concrete slabs exert a
substantial restraint action and greatly increase the elastic critical tangential stress for global buckling.
The no-warping model ( kcr ,g 60.4 ) has been recommended for the analysis of the corrugated-plate
webs of prestressed composite box girders (46).
15 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
Inelastic global buckling may occur when cr ,g 0.8 y , and the inelastic critical tangential stress (44,9) can
be calculated as
cr ,g ,in 0.9 cr ,g y
(18)
Interactive buckling
Interactive buckling was identified in tests on corrugated plates (44) carried out in Sweden. It results from
the interaction between local and global buckling modes, is a sudden phenomenon characterized by a
sharp snap and steel plasticization along the folds, and is critical in webs with folds of intermediate depth.
The following equation has been proposed for the critical tangential stress cr ,i for interactive buckling
1
cr ,i
(19)
cr ,l cr ,g
Inelastic local and global critical stresses, equations (13) and (18), are used in equation (19) when the
corresponding elastic critical stress exceeds 80% of the yield point of steel. The interaction among the
three buckling modes and the tangential stress at yielding is shown in Figure 12 for an 8mm plate with
trapezoidal corrugation, fy 350N mm2 , hw tw 250 , kcr ,g 60.4 and 30 . El Metwally (47) has
proposed an interaction equation inclusive of shear yielding to predict failure of corrugated-plate webs
within the entire practical range of corrugation parameters
1
cr ,i
1
cr ,l
1
cr ,g
1
y
(20)
The recommended values for the exponent are k 2 for trapezoidal corrugation and k 3 for zigzag
corrugation. Prior to reaching the shear yielding point of the panel, the post-critical strength of
corrugated-plate webs depends on the width of the sub-panels. The ultimate shear capacity of wide subpanels may be twice their local buckling
capacity, while narrow or shallow
Figure 12: Non-factored critical tangential stress
corrugations offer minimal post-critical
600
domain due to global buckling.
local (10)
500
local (13)
global (14)
global (18)
interactive (19)
yielding
Block distributions of yield strains have been used to study the effects of mechanical folding of the plates.
Because of the cold-forming process used for corrugation, yield strains and the degree of strain-hardening
16 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
at the folds of the corrugation profile are higher than in the flat regions of the panels (48). Folding does not
seem to have significant effects on the ultimate strength of the panels.
Pr 15.6wtbtw fy 1 w
240
(21)
where t b is the thickness of the bottom flange and Lw is the length of the patch load along the web edge,
both expressed in millimeters. In a prestressed composite box girder, the ultimate capacity for web
yielding is calculated based on axial yielding of an effective web length resulting from 45 dispersal of the
support reaction throughout the bottom web-slab node. In the most complex cases, more accurate
distribution of the vertical axial stress may be attained with finite-element analysis of models including
bearings and bottom web-slab node (4).
In-plane bending and shear diminish the vertical patch-load capacity of a corrugated-plate web. The
following interaction has been proposed (51) for combined patch loading and in-plane bending, where P is
the patch-load capacity in the presence of the bending, M is the bending capacity in the presence of
patch load, Pr is the ultimate patch-load capacity in the absence of bending, and Mr is the ultimate
flexural capacity in the absence of patch loading
Pr
M
Mr
(22)
17 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
I-girders with flat stiffened-plate webs may be checked with k 2 (54). A more conservative value
k 1.25 has been proposed for corrugated-plate webs devoid of bottom slab (9). The flexural and shear
stiffness of the bottom web-slab node justifies the use of k 2 for a prestressed composite box girder.
The following interaction has been proposed for combined patch loading and in-plane shear (9), where Vr
is the ultimate shear capacity of the cross-section
Pr
V
1
Vr
(23)
The stiffness of the bottom web-slab node justifies the use of k 1.8 in a prestressed composite box
girder.
Resistance factors
Different resistance factors are used for the different buckling modes of a corrugated-plate web to reflect
the different post-critical domains; allowance is also made for geometry imperfections in the box girder
and the corrugation folds, and for residual stresses in the folds in relation to the corrugation process. The
resistance factors for the fillet welds of web to flanges, the flanges, and the shear connectors are specified
by the applicable design standards for non-prestressed composite bridges.
French researchers (39,55) proposed the use of cr ,g 0.50 for global buckling and of cr ,i 0.67 for
interactive buckling. These resistance factors were used for the design of the Pont de la Corniche (39). A
lower resistance factor for global buckling, cr ,g 0.33, was used for the design of the Charolles Bridge.
Further research could lead to relaxation or refinement of the resistance factors, especially in relation to
global buckling. When global buckling occurs, the shear strength decreases and the corrugated plate must
develop large diagonal deformations required for stretching the folds prior to being able to transfer
diagonal tension through membrane action. Tests confirmed the existence of a post-critical domain for
global buckling, but the deformations necessary to achieve post-critical stability may be excessive for
bridge structures. The resistance factors for global and interactive buckling are therefore lower than the
resistance factor for local buckling, whose post-critical domain is stable and well known. The resistance
factor for local buckling (38) may be taken as
Figure 13: Factored critical tangential stress
250
200
150
local (10)
local (13)
interactive (19)
yielding
global (14)
global (18)
100
50
0
0
200
400
bw (mm)
600
800
ultimate limit state is taken as the smallest of the factored critical tangential stresses calculated for
yielding and local, global and interactive buckling for the given corrugation parameters. Starting from
Figure 12, the interaction among the three buckling modes and shear yielding is shown in Figure 13 for
cr ,g 0.50 , cr ,i 0.67 and cr ,l 0.91 . The design of a corrugated-plate web typically starts for
18 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
d y 0.8 and the practical consequence of the application of resistance factors is narrowing the choice
of b f for a given set of corrugation parameters.
(24)
For efficient use of steel it should be d y 0.8 , and therefore it remains to find t w and b f . The
following procedure has been proposed (19).
1. Determine t w from the factored shear force, the factored tangential stress at yielding, and the
plate thickness commercially available.
2. Assume an initial value of bf tw .
3. Determine the critical tangential stress for local buckling with equation (10). The factored critical
tangential stress typically exceeds the tangential stress at yielding and rarely governs design.
4. Input a start value for the critical tangential stress for interactive buckling into equation (19), for
example cr ,i ,d 0.9 y
5. Based on
cr ,i
and
cr ,l
, determine
cr ,g
Working on equations (10) and (11), d can be expressed as a function of bf tw and hw tw . Design
charts with bf tw in abscissa and hw tw in ordinate can be drawn for the desired ratio d y and the
chosen corrugation parameters. Design charts with hw tw in abscissa and d y in ordinate can be
drawn for different values of bf tw to determine the most efficient corrugation parameters in the
0.8 d y 1 range based on a chosen fold angle. Figure 14 has been obtained with the corrugation
parameters and the resistance factors of Figures 12 and 13. Design charts with b f in abscissa and d y
in ordinate can also be drawn for different values of hw tw , Figure 15.
The design charts may be based on non-factored tangential stresses for analysis of the physics of
instability, or on factored stresses for design purposes. The critical tangential stresses for the different
buckling modes can be enveloped with the following equation
d cr ,l cr ,l k cr ,g cr ,g k cr ,i cr ,i k s y k
1 k
(25)
19 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
The tangential stress thus determined is always smaller than the individual stresses on the right-hand side
of the equation, and the exponent governs the shape of the transition. A large exponent makes the curve
to tightly follow the six bounding equations (local buckling below and above 0.8 y , global buckling below
and above 0.8 y , interactive buckling and factored tangential stress at yielding). The dotted line in Figure
15 has been calculated with k 10 .
Figure 14: Design chart
1.2
bf/tw=80
bf/tw=40
bf/tw=60
bf/tw=20
1.0
td/ty
0.8
0.6
0.4
0.2
0.0
0
100
200
300
400
500
600
700
800
hw/tw
1.0
td/ty)
0.8
0.6
hw/tw=400
hw=tw=300
hw/tw=200
hw/tw=200; equation (25) k=10
0.4
0.2
0.0
0
200
400
600
800
20 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
dimensions depend on commercial standards, and it is reasonable to assume that steel plates of width
hw up to about 3m, thickness t w up to 12mm, and length up to 15m, are available for corrugation.
Continuous, highly-automated manufacturing processes have been developed for fabrication of built-up
I-girders with 2-3mm corrugated webs for building and crane applications (59). At the beginning of the
assembly line, a de-coiler feeds the web plate into a stretch leveler followed by the corrugation unit. The
depth of the sinusoidal corrugation ranges between 30mm and 45mm, and the depth of the web may
reach 1500mm. While the finished web is transported through the assembly line continuously, both
flanges are placed into position and fixed
Figure 16: Pressing equipment
to the web by means of hydraulic clamps.
Together they pass through the welding
unit for continuous one-sided fillet welding
under submerged arc. The entire
manufacturing process takes place at a
speed of 2m per minute.
Cold pressing is likely to be the least
expensive method for forming the
corrugation of 8-12mm web plates for
bridge applications. The webs for the Cognac Bridge in France were corrugated by flipping the plate over
after each pressing. Eventually, one complete 4-fold corrugation was cold-pressed at a time by placing
the plate on rollers to avoid stretching, Figure 16.
Presses for steel plates up to 4m-wide are available in Europe. The pressing force Fp for the generation of
four cylindrical plastic hinges in the plate can be estimated by replacing the yield stress of steel with the
tensile strength fu to allow for strain hardening (36)
Fp fu
tw2 hw
af
(26)
Wp futw2 hw
(27)
For fu 510N mm2 , tw 8mm , hw 1000mm , 30 and bf 300mm , the pressing force and
energy are Fp 126kN and Wp 17.1 kJ . The cycle time is mainly governed by the time taken to move the
plate one wavelength between each stroke. Even if the cycle time is as short as 10 sec, the mean power
required for pressing is only 17.1 10 1.7 kW . At this rate, corrugation of a 14.5m-long plate would take
about 2 min and provide a 13.5m length of web (12 complete corrugations with 1120mm wavelength,
w 1.072). Heavier presses would be needed for a 12mm web plate, 2.0m wide. As b f is likely to be
proportional to t w , the pressing force is proportional to tw hw and so would be Fp 378kN in this case.
The angle is generally between 25 and 32. This enables a generous bend radius, such as 10 tw , to be
used for the folds, which also reduces the stress concentration in the flange-to-web welds at the folds.
The flange plates are welded orthogonal to the corrugated webs, and the box girders with inclined webs
are obtained with haunches in the concrete slabs at the web-slab nodes. Submerged-arc joint tracking
equipment (58) may be used for welding; profiled gas-shielded fillet welding is often used for the 3mm
corrugated webs used in buildings. Conventional weld control technology is applicable to these welds.
Handling and transport requirements and the wavelength of the folds govern the optimum length of the
web segments, which often governs the modularity of the slab segments of the prestressed composite
Marco Rosignoli, Dr.Ing., PE | Bridge Engineering eManuals All Rights Reserved
21 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
box girder. The web segments used for the Charente Bridge in France were 12m long. Web segments
ranging from 10m to 14m were used for the Charolles Bridge in France in combination with 12m slab
segments. The web segments used for the Ginzan-Miyuki Bridge in Japan were 5.5m long in combination
with 11m slab segments. The web segments for balanced cantilever bridges are typically shorter to match
the length of the casting cell of the form travelers (1).
Web segments can be spliced by overlapping and double fillet welding or by slip-critical bolted
connections, with or without cover plates. Double fillet welds are designed for shear and the horizontal
bending (3) due to axial shortening of the box girder at the application of prestress. The flange plates are
rarely spliced. Field splicing is simpler and less expensive than for the I-girders of non-prestressed
composite bridges. Procedures for cambering corrugated webs (36) have been proposed; cambers are not
used in prestressed composite box girders built by incremental launching (2,3,4).
22 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
form table is extracted backward after launch and repositioned for the new slab segment. Concrete
pouring in the two casting cells is staggered over time to optimize labor rotation.
Internal launch tendons (4) are anchored at the rear construction joint to simplify strand insertion and
tendon stressing from the rear anchorages. Internal tendons are spliced by coupling or overlapping and
may be tensioned after a short curing time. If the front casting cell is sufficiently far from the launch
abutment, internal launch tendons may cross 2 or 3 slab segments. External polygonal launch tendons
are anchored by splicing in double anchor beams, and temporary deviators made of steel or concrete are
necessary at the top slab level for deviation of antagonist tendons (4).
Incremental launching is likely to be the most competitive construction method for prestressed
composite box girders with simple geometry, 40-50m spans and a few hundred meters of length.
Launching the completed deck is simpler and more rational than launching the steel girder and
completing the cross-section by casting the concrete slabs in-place, although the deck is much heavier
during launch. Compared with the launch of the steel girder of a non-prestressed composite bridge, the
deck is several times heavier, the webs are thinner, and the launch stresses may therefore be critical.
The launch nose is typically quite long (2,3,4) to reduce the peaks of negative bending and shear in the front
deck region. A long launch nose is not particularly expensive with a lightweight deck cross-section, and the
steel corrugated-plate webs themselves can be used as a launch nose. The bottom slab is cast full-length
in the casting yard to achieve a regular launch surface for the deck, and the top slab of the front span is
cast in-place on launch completion. The front U-girder thus obtained is lighter than the completed deck,
and structurally more efficient under negative bending. Heavier top flanges are used for the webs in the
launch nose region, and temporary lateral braces and cross frames are applied to enhance stability.
The resistance to lateral torsion-flexure buckling of I-girders with corrugated-plate webs is different from
that of I-girders with stiffened-plate webs (60,61), and the critical moment is slightly higher. The equations
specified by the design standards for the equivalent moment factors of plane webs also seem to apply for
the analysis of the effects of moment gradients. However, the research available on lateral torsion-flexure
buckling of I-girders with corrugated-plate webs is minimal, and finite-element analysis is recommended
for analysis of launch nose stability.
When the bottom slab is wide and the front U-girder is therefore heavy, the use of a front cable-stayed
system (4) may be less expensive than a custom launch nose. This solution requires a load distribution
diaphragm under the mast, and the localized load applied to the deck disturbs the envelopes of launch
bending and shear. The deflection of the front cantilever may be recovered with a hydraulic pantograph
applied to the front deck end.All the thrust
Figure 17: Local eccentricity of support reactions
systems (3,4) for PC bridges may be used for
launching. Rear thrust beams applied to the
bottom slab are particularly effective, as the
launch force and the frictional resistance of
the launch bearings remain within the
bottom slab and do not generate interface
shear transfer at the bottom web-slab
nodes. When Eberspcher launchers (4) are
used at the abutment, PLC control of the
low-speed final approach of the support
saddles avoids sudden application of vertical
loads to the deck. The bottom flanges are
23 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
located over the bottom slab to take advantage of slab thickness for longitudinal dispersal of the support
reaction within non-stiffened webs. Haunches may be used to further spread the load and to improve web
stability with a smaller panel depth.
Web corrugation makes the support reactions eccentric in the transverse plane, and the bottom slab
must therefore resist local bending, Figure 17. Lateral launch guides are used at every pier to avoid
additional load eccentricity. Haunches in the bottom slab increase the transverse flexural stiffness and
improve bottom flange stability far from the connectors. This scheme of web-slab node also improves
corrosion protection by moving the triple contact point far from the web-flange weld.
The absence of cambers avoids angle breaks in the launch surface, and fewer modes of instability can
arise in the web panels. Elastic stability of a corrugated plate is better than the one of a stiffened plate
because the distance between the folds is much shorter than the typical spacing of vertical stiffeners.
However, the corrugated-plate webs are thinner, and longitudinal dispersal of the support reactions
often requires the use of long launch bearings (4).
The high flexural stiffness of the box girder reduces the rotations of the support sections; in spite of this,
rocking launch bearings are often necessary to spread the support reactions uniformly. Articulated
bearings (1) soon become too flexible and expensive, and steel skids topped with polished stainless-steel
sheets for low-friction sliding of Neo-flon plates are placed onto longitudinal batteries of interconnected
jacks to create hydraulic hinges (1,4). Control valves between the two hydraulic launch bearings at each
pier can be used to generate torsional hinges.
The longitudinal axial stress in the bottom slab is significant in the negative bending regions. Although the
central region of the web panels is subject to negligible axial stress, the flanges and the adjacent web
regions undergo the same longitudinal strains as the concrete slabs. The local stresses are easy to
calculate under the assumption of strain compatibility; since they do not contribute to the elastic
equilibrium, they may be reduced by cutting the flanges at a regular distance. The flanges may also be left
discontinuous at the field splices, with additional labor savings. This solution was adopted in the 80m
balanced-cantilever spans of the Pont de la Corniche in France (39,62,63).
The prestressed composite box girders built by incremental launching resist full self-weight shear prior to
the application of polygonal tendons at the end of launch. The tangential stresses in the webs are high
during launch, and additional tangential stresses due to torsion and distortion should be avoided as much
as possible with accurate alignment of the launch bearings. Launch bearings on hydraulic jacks offer the
additional advantage of real-time monitoring and equalization of the support reactions.
Case studies
Prestressed composite box girders are also fit to balanced cantilever construction on medium spans. In
varying-depth bridges, steel corrugated-plate webs increase the cross-sectional flexural efficiency
significantly. The 496m Pont de la Corniche in France (39,62,63) includes with five 80m spans and two 48m
end spans. The top slab is 14.5m wide and the width of the bottom slab increases from 5.15m at the piers
to 7.2m at midspan, for a constant web inclination of 17. The overall depth of the cross-section is 2.5m
at midspan and 5.5m at the piers. The clear depth of the corrugated-plate webs between flanges ranges
from 1081mm at midspan to 4011mm at the piers. Plate thickness is 8mm for typical web segments,
10mm near the piers, and 12mm near the tendon deviation diaphragms.
The webs are welded to 350x14mm flanges equipped with 150x15 L-shape connectors spaced 430mm
and 370mm ( bf and af , respectively) and 200mm wide, and the depth of the transverse folds is 220mm.
Fold wavelength is 1600mm, and the web segments are 3280mm long for 80mm overlap at the field
24 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
splices. The long-term flexural efficiency of the composite cross-section, equation (4), is f 0.625 at
midspan and f 0.788 at the piers. Longitudinal prestressing consists of three families of tendons:
rectilinear 12T15 cantilever tendons anchored at top slab joints during balanced cantilever construction,
rectilinear 12T15 continuity tendons in the bottom slab at midspan, and polygonal 19T15 tendons for
service loads, tensioned on deck completion. The following quantities of materials were reported per
square meter of deck surface: 0.57m of 35MPa concrete, 26kg of T15 strand, 124kg of reinforcing steel,
and 39kg of steelwork.
Construction on falsework is a viable option for short bridges that do not allow the investment required
by incremental launching technology. A three-span prestressed composite box girder was built on
falsework at Cognac, France on a 42.9m main span and two 32.5m end spans (64,65). The top slab is 11.7m
wide, the bottom slab is 4.17m wide, and the total depth of the cross-section is 2.285m. The thickness of
the top slab varies from 0.23m to 0.33m.
The folds in the 8mm web plates have longitudinal and inclined width of 353mm and are 150mm deep.
The net depth of the web panels is 1770mm, and the transverse inclination of the steel webs is 40. The
flange plates are 250x10mm at the top and 330x10mm at the bottom, and are equipped with 250mmwide, 100x9 L-shape connectors spaced 353mm at midspan and 159mm in the support regions. The
short-term flexural efficiency of the cross-section is f 0.659 . Eight 19T15 external tendons anchored
at the end diaphragms required the use of concrete deviation diaphragms. The following quantities of
materials were reported per square meter of deck surface: 0.41m of 40MPa concrete, 15.3kg of T15
strand, 67.3kg of reinforcing steel, and 31.5kg of steelwork.
A 30m, twin box-girder span was built in Japan (66,67,68) with 70 skew angle. The deck is 14.8m wide and
the bottom slab of each box girder is 2.1m wide. The box girders are 1.9m deep, and the height of the
corrugated-plate webs is 1183mm. Internal and external tendons were used for longitudinal prestressing.
So far, few prestressed composite box girders with steel corrugated-plate webs have been built by
incremental launching. Construction of the Maupre Bridge in France gave researchers (69,70,71,72,73) the
opportunity of comparing different types of prestressed composite box girders. The bid design proposed
two solutions: a stiffened-plate prestressed composite box girder built by incremental launching, and a
PC space frame built as balanced cantilevers. Among numerous alternatives, the solution of Figure 17 was
chosen for incremental launching construction of a seven-span continuous deck with spans ranging from
40.9 to 53.6m and a total length of 327m. With a top slab width of 10.75m, the cross-sectional depth is
3.05m for a 17.6 span-to-depth ratio. The Maupre Bridge was competed in 1987.
A 610mm diameter, 20.6mm-thick steel pipe replaced the bottom slab. Concrete filling stiffened the pipe
walls against instability and improved dispersal of the launch support reactions. The steel girder includes
two 45-inclined corrugated-plate webs shop-welded to the bottom pipe, so that complete V-units were
shipped to the site for assembly. The webs are 8mm thick, the longitudinal and inclined panel width is
284mm, the fold depth is 150mm, and the fold wavelength is 1050mm. The 300x10mm top flanges are
equipped with 100x10 L-shape connectors with constant 284mm spacing.
The top slab is 10.75m wide with 2.80m side wings, and its thickness ranges from 0.20m to 0.30m at the
flanges. Because of the triangular shape of the cross-section, the migration of launch support reactions
generates transverse tensile stresses in the slab strip between the flanges. Rectilinear HDPE-coated T15
mono-strands were used for transverse top slab post-tensioning.
The deck was built by welding the field splices of 10-13m girder segments and by casting the
corresponding segments of top slab and pipe infill. Pipe filling required the use of a vibrating feeding
25 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
pipe. On filling completion, the hole left by the vibrating pipe was filled with high-pressure grout to
create a residual radial compression in the concrete infill.
The triangular cross-section is not subject to distortion during launch. In the absence of a bottom slab,
the flexural stiffness is relatively small, similar to the one of a non-prestressed composite bridge. Large
flexural rotations at the supports required the use of hydraulic launch bearings (4), and the concrete-filled
bottom pipe provided a major contribution to the dispersal of support reactions.
Launch prestressing was applied with 12 or 14 permanent horizontal external 6T13 tendons located near
the top slab and anchored from pier to pier to anchor beams protruding from the top slab. Transverse
post-tensioning in the concrete slab was increased at the anchor beams for enhanced dispersal of the
anchor loads. Prior to tensioning the launch tendons of the new segment, steel props supported on the
bottom pipe were used to reduce torsion in the rear anchor beam. The concrete slab of the front span
was cast on launch completion to use the lighter front deck portion as a launch nose.
On launch completion, prestressing was completed with four 19T15 external tendons anchored to the
end diaphragms of the bridge and deviated by steel pier diaphragms and steel saddles welded to the
bottom pipe at the span thirds. Polygonal post-tensioning balanced more than 80% of the permanent
loads and recovered most of self-weight deflections. The tendons were jacked vertically at the central
pier diaphragm to recover part of the friction losses in the 330m tendons.
The use of a concrete-filled pipe instead of a bottom slab assured dispersal of the support reactions and
avoided secondary transverse stresses. It also posed new problems, related to the long launch bearings,
the transverse deck stability during launch, and the need to assure a reliable connection between the
steel pipe and the concrete infill for control of local buckling. The following quantities of materials were
reported per square meter of deck surface: 0.25m of concrete, 1.5kg of transverse strand, 5.7kg of launch
strand, 8.5kg of polygonal strand, 58.6kg of reinforcing steel, and 95.2kg of steelwork. Steelwork includes
47.8kg of corrugated-plate webs, 28.3kg of steel pipe, 2.3kg of connectors, and 16.8 kg of diaphragms.
The Ginzan-Miyuki Bridge (74) was built by incremental launching in Japan. The 5-span box girder has a
total length of 210m and includes four 45.5m spans and a 27.4m span. The cross-section includes a 9.3mwide, 0.30m-thick top slab and a 3.9m-wide bottom slab whose thickness varies from 0.25m at midspan
to 0.50m in the support regions. The deck has a constant depth of 3.0m with a span-to-depth ratio of
15.2. Plate thickness in the 2210mm web panels varies from 9mm to 12mm, the plate folds have
longitudinal and inclined width of 300mm, and the fold depth is 150mm. External prestressing tendons
are as long as two spans to reduce friction losses at the deviation points.
The bridge includes 19 segments with constant 11m length. The 33m-long front section of the top slab
was cast on launch completion to avoid the use of a launch nose, and the weight of the bottom slab
required the use of a front cable-stayed system. The steel mast was located 2.2m behind the leading pier
when the front deck end was landing at the new pier. Comparisons between the dynamic deck behavior
predicted by finite-element analysis and the vibration modes measured with dynamic tests on the bridge
confirmed a significant influence of the shear strains on the vertical modes (75). However, the vibration
frequencies of the external tendons are much higher, and this prevents resonance effects.
Starting from these first applications, several prestressed composite box-girder bridges with steel
corrugated-plate webs have been built in Japan in the last 15 years (24). The 198m Hondani Bridge has a
97.2m central span, 11.4m-wide top slab, 6.2m-wide bottom slab, and box girder depth varying from
6.4m at the piers to 2.5m at midspan. The bridge used concrete dowel connectors (76,77,78,79).
26 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
Symbols
a
af
cross-sectional area
Ac
As
bf
cf
Dx
Dz
em
efficiency of material
Ec
Es
E x ,eff
ultimate stress
fu
fy
force
Fh
anti-symmetrical force
Fp
Fs
Geff
Gs
hf
hw
kcr ,g
kcr ,l
Lw
mz
bending moment
27 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
Mr
Pr
tb
tw
web thickness
torsional moment
shear force
Vb
Vt
Vw
Wp
zl
zu
corrugation angle
Poissons Ratio
1,2
tangential stress
cr
cr ,d
cr ,g
cr ,i
cr ,l
28 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
y ,d
References
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
29 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
25. Harrison, J.D. (1965). Exploratory Fatigue Tests of Two Girders with Corrugated Webs. British Welding
Journal. 12, No. 3, pp. 121-125.
26. Korashy, M.; Varga, J. (1979). Comparative Evaluation od Fatigue Strength of Beams with Web Plate
Stiffened in the Traditional Way and by Corrugation. Acta Technica Academiae Scientiarum
Hungaricae, pp. 309-346.
27. Rosignoli, M. (1999). Prestressed concrete box girders with folded steel plate webs. Proceedings of
the Institution of Civil Engineers Structures and Buildings, February.
28. Combault, J. (1988). Viaduct du vallon de Maupre, a Charolles. Travaux, January.
29. Aribert, J.M. (1988). Connexion au cisaillement des poutres fatigue determination experimentale de
la resistance. Annales ITBTP, September.
30. Johnson, R.P. (1997). Shear connection for composite bridges and Eurocode 4: Part 2. IABSE FIP-CEB
International Conference, Innsbruck, Austria.
31. Kristek, V., Vitek, J.L. (1997). Performance and stud failure in steel-concrete composite beams. IABSE
FIP-CEB International Conference, Innsbruck, Austria.
32. Rosignoli, M. (2015). Design and construction of launched bridges. Two-day class in New York City,
ASCE Continuing Education Program.
33. Libove, C. (1973). On the Stiffness, Stress and Buckling of Corrugated Shear Webs. Proceedings of the
2nd Specialty Conference on Cold Formed Steel Structures. University of Missouri-Rolla, pp. 259-301.
34. Libove, C. (1977). Buckling of Corrugated Plates in Shear. Proceedings of the International Colloquium
on Structural Stability. Structural Stability Research Council, Lehigh University, pp. 435-462.
35. Timoshenko, S.P.; Gere, J.M. (1981). Theory of Elastic Stability. 2nd edition, Mc-Graw Hill, New York.
36. Cafolla, J., Johnson, R.P. (1997). Fabrication of steel bridge girders with corrugated webs. The
Structural Engineer, April.
37. Galambos, T.V. (1988). Guide to stability design criteria for metal structures. John Wiley and Sons,
New York.
38. EN 1993-1-1:2005 (2005). Eurocode 3 Design of Steel Structures Part 1.1: General Rules and Rules
for Buildings. UNI, Ente Italiano di Unificazione.
39. Reinhard, J.M. (1994). Pont de la Corniche Dole. Ouvrages dArt 19, November, No. 19, pp. 14-19.
40. Easley, J.T. (1975). Buckling Formulas for Corrugated Metal Shear Diaphragms. Journal of the
Structural Division. ASCE, St. 7, pp. 1403-1417.
41. Easley, J.T.; McFarland, D.E. (1969). Buckling of light-gauge corrugated metal shear diaphragms. ASCE
Journal of Structural Engineering, 95(7), pp. 1497-1516.
42. Peterson, J.M.; Cord, M.E. (1960). Investigation of the Buckling Strength of Corrugated Webs in
Shear. Technical Note D-424. NASA.
43. Moreau, P.; Thivans, P. (1984). Structures composites acier-bton precontraint. Annales ITBTP,
January.
44. Bergfelt, A.; Leiva-Aravena, L. (1984). Shear Buckling of Trapezoidally Corrugated Girder Webs. Report
No. S84:2. Department of Structural Engineering, Chalmers University of Technology, Gteborg,
Sweden.
45. Cheyrezy, M. (1987). Analyse des Conditions de Flambage des Ames Plissees. Actes du 3e colloque
Genie Civile et Recherche.
46. Johnson, R.P.; Cafolla, J. (1997). Corrugated webs in plate girders for bridges. Proceedings of the
Institution of Civil Engineering, Structures and Buildings. 123, pp. 157-164.
47. El Metwally, A.S.; Loov, R.E. (1998). Prestressed composite girders with corrugated steel webs.
Proceedings of the 5th International Conference on Short and Medium Span Bridges. Calgary, pp.
1175-1187.
30 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
48. Luo, R.; Edlund, B. (1994). Buckling of trapezoidally corrugated panels using pline finite strip method.
Thin Walled Structures, 18: 209-240.
49. Levia-Aravena, L. (1987). Trapezoidally Corrugated Panels Buckling Behaviour Under Axial
Compression and Shear. Division of Steel and Timber Structures, Chalmers University of Technology.
Publ. 87:1.
50. Johnson, R.P.; Cafolla, J. (1997-b). Local flange buckling in plate girders with corrugated webs.
Proceedings of the Institution of Civil Engineering, Structures and Buildings. 123, pp. 148-156.
51. Elgaaly, M.; Hamilton, R.; Seshadri, A. (1996). Shear Strength of Beams with Corrugated Webs.
Journal of Structural Engineering, ASCE, Vol. 122, No. 4.
52. Bergfelt, A.; Edlund, B.; Leiva-Aravena, L. (1985). Trapezoidally corrugated girder webs shear
buckling, patch loading. Summary Report S84:2. Division of Steel and Timber StructuresChalmers
University of Technology, Gteborg, Sweden.
53. Luo, R.; Edlund, B. (1996). Ultimate strength of girders with trapezoidally corrugated panels under
patch loading. Thin Walled Structures, 24: 135-156.
54. Elgaaly, M. (1983). Web Design Under Compressive Edge Loads. Engineering Journal, AISC, 4th Qtr.,
pp. 153-171.
55. Various Authors (1987). Innovation dans le domaine des structures mixtes: ponts mixtes metal-beton
precontraint. Annales ITBTP, OctoberNovember.
56. Cafolla, J., Johnson, R.P. (1997-c). Local flange buckling in plate girders with corrugated webs.
Proceedings of the Institution of Civil Engineers Structures and Buildings, May.
57. El Metwally, A.S.; Loov, R.E. (1998-b). Composite girders High strength concrete combined with
corrugated steel webs. Proceedings of the International Symposium on High Performance and
Reactive Powder Concrete. Sherbrooke, Vol. 1, pp. 197-215.
58. Arsicault, M.; Lallemand, J.P. (1990). Joint Tracking with Self-Teaching Systems. Welding Journal,
December.
59. Siokola, W,; Poeter, H. (1999). Fabrication tools for corrugated web I-beams. Modern Steel
Construction, July.
60. Lindner, J. (1990). Lateral-Torsional Buckling of Beams with Trapezoidally Corrugated Webs.
Proceedings of the 4th International Colloquium on Stability of Steel Structures, Budapest, Hungary.
61. Sayed-Ahmed, E. Y. (2005). Lateral torsion-flexure buckling of corrugated web steel girders.
Proceedings of the Institution of Civil Engineers, Structures & Buildings. 158, pp. 53-69.
62. Capra, A.; Leville, A. (1996). The bridge at Dole. Proceedings of the FIP Symposium, Post-Tensioned
Concrete Strucures. London, Vol 1., pp. 135-141.
63. Lebon, J. (1998). Steel corrugated web bridges first achievements. Proceedings of the 5th
International Conference on Short and Medium Span Bridges. Calgary, Proceedings CD.
64. Cassiau, A., Combault, J., Duviard, M. et al. (1988). Pont sur la Charente Cognac. Travaux, October.
65. Duviard, M. (1987). Le premier pont ames plisses Cognac. AIPCIABSE Congress, Paris-Versailles.
66. Naito, T.; Hattori, M. (1994). Prestressed concrete bridge using corrugated steel webs Shinkai
Bridge, XII FIP Congress. National Report, Washington, pp. 101-104.
67. Yoda, T.; Ohura, T.; Sekii, K. (1994). Analysis of composite PC box girders with corrugated steel webs.
Proceedings of the 4th International Conference on Short and Medium Span Bridges. Halifax, pp. 11071115.
68. Yoda, T.; Ohura, T.; Sato, Y. (1994). Torsional behaviour of composite PC box girders with corrugated
steel webs. Proceedings of the 4th International Conference of the Association for Research in SteelConcrete Composite Structures. Kosci, Slovakia, pp. 458-461.
69. Bonnet, M., Bouvy, B., Causse, G. et al. (1988). Viaduc du vallon de Maupr, Charolles (Saone-etLoire). Travaux, October.
31 | 3 2
Prestressed Composite Bridges with Steel Corrugated-Plate Webs | BEeM 101.01 November 2015
70. Causse, G. and Duviard, M. (1987). Maupre viaduct near Charolles. A bridge deck with corrugated
steel plate webs constructed by the incremental launching technique. AIPCIABSE Congress, ParisVersailles.
71. Combault, J. (1988). The Maupre Viaduct near Charolles. AISC NEC/COP National steel construction
conference, 1988, Miami Beach, Florida.
72. Combault, J. (1988). The Maupre Viaduct Near Charolles, France. Proceedings of the AISC Engineering
Conference, 12.1-12.22.
73. Nadal, P. (1987). Le Viaduct de Maupr Charolles. Chantiers de France, November.
74. Isiguro, W., Murata, Y., Sugo, T. and Uehira, K. (1997). Stability of prestressed concrete bridge with
corrugated steel web. AIPCIABSE International Conference for Composite Construction
Conventional and Innovative. Innsbruck, pp. 205-210.
75. Tategami, H.; Hajikawa, Y.; Honda, H.; Euhira, K. (1997). Dynamic behaviour of a PC box girder bridge
using a corrugated steel web. Proceedings of the New Technology in Structural Engineering
International Conference. Lisbon, Vol. 2, pp. 715-722.
76. Leonhardt, F. (1987). New improved shear connector with high fatigue strength for composite
structures. Beton und Stahlbetonbau. Vol. 12, pp. 325-331.
77. Roberts, W.S.; Heywood, P. (1994). An investigation to increase the competitiveness of short span
steel concrete composite bridges. Developments in Short and Medium Span Bridge Engineering. pp.
1161-1171.
78. Yoda, T.; Ohura, H. (1995). Effects of shear connectors on mechanical behaviour of composite girders
with corrugated steel webs. Proceedings of the 4th Pacific Structural Steel Conference. Singapore, pp.
117-121.
79. Yoda, T.; Takeshita, A.; Sato, K.; Sakurada, M.; Shiga, H.; Nakasu, K. (1998). Fatigue tests of a new
type of shear connectors in a composite girder with a corrugated steel web. Proceedings of the 5th
International Conference on Short and Medium Span Bridges, Calgary, pp. 1651-1658.
32 | 3 2