Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Data:
Building size : 15m x 15m
Height : 33m
Concrete Mix : M30 Steel Grade: Fe415
Loads: LL =1.50 KN/m2 (For Roof slab) 2.0KN/m2 (For floor slab)
Member sizes : Beams 300 x 450mm; Columns 300x 450mm
Slab thickness: 120mm.
15.00
3.00
3.00
3.00
3.00
3.00
15.00
PLAN
33.00
3.00
3.00
3.00
3.00
3.00
15.00
ELEVATION
STATIC PROJECT:
1 Geometry Creation:
New Project Select Space Length =meters; Force=KN;
File Name=Seismic Coefficient by Member weight method (MW) Next
Select Open Structure Wizard Finish.
Change to Frame models from Truss models Select Bay Frame and double
click
on it.
Length X=15.0m No. of Bays =5
Height Y=3.0m
Width Z=15.0m
Go to front view.
2. Member Property :
Click General Property Define Rectangle
YD=0.45
ZD=0.30
Add
YD=0.45 ZD=0.30 AddClose . Highlight 0.45 x 0.30 Main menu
Select
Beam parallel to X , Select Beam parallel to Z Assign to selected
beam
Assign Yes Highlight 0.45 x 0.30 Select Beam parallel to Y
Assign to selected beam Assign Yes Close.
Deselect the nodes. Select beam cursor. Select the entire structureClick
Translational
repeat Y No. of steps=10 Default spacing=3m Link OK.
3. Supports :
Go to front view.
Click Support Create Fixed Add. Highlight support 2 and select
bottom most
support nodes by windowing using node cursor Assign to selected nodes
Assign Yes Close De select the nodes and change to beam cursor.
4. Loads :
Click Loads and Definitions Click Load case details Add.
Primary No.1 Type: Dead
Title: Dead Load Add.
Load case details Add.
Number 2
Type: Live
GYAdd.
Max.=33.0m Add.
Max.=30.0m Add.
Max.=33.0m Add.
1=1.5
Load case 2
Plan view Select outer portion of beam and highlight w1=- 4KN/m
Assign to
Selected beam Assign YesClose.
5. Analysis Type :
Click Analysis/print No print Add.
Click Post printDefine CommandsAnalysis resultsAddClose.
6.. Perform Analysis :
From Main Menu ` Analysis Run Analysis
View output file Done.
Procedure for converting Static project to Equivalent Seismic Analysis:
Step 4: Loading
Loads already specified are
1.Dead Load
2.Live Load
3.Load Combination
***
Main menu Commands Loading Definitions Seismic load IS 18932002 (OR)
Click loads & Definitions Add.
Seismic parameter screen will appear.
Select Type: IS 1893-2002 Generate Add.
IS1893 seismic parameters screen will appear.
Select Zone =III. Z=0.16
Response reduction facto (RF) : (For Special RC MRF) = 5
Importance factor (I) =1.5
Rock/soil type (SS) : (For Medium soil)=2
Structure Type (ST) : (For RC Frame Building)=1
Damping Ratio (DM) = 0.05%
Period in X = 0.09 h =0.09 x33
dx
12
=0.86 sec.
=0.86sec.
12
: 4 OK.
Rule No.
1
2
3
4
Dead
1.5
1.5
1.2
0.9
Live
1.5
-1.2
---
Seismic
-1.5
1.2
1.5
Output
Selected:
1. Sections
2. Supports
3. Loadings
Beam End Forces
Reactions
Beam Max Axial Forces
Beam Max moments
Max. Shear Forces
Beam Force Details Summary Ok.
Report:
Click Report setup icon Click input from available from left side.
Select Sections , Supports, Loadings and sent to Right side by clicking >
Select output.
From output select Beam end forces, Reactions, Bending moment, Shear
forces, Axial
forces , Beam force detail summary.
To Take picture:
Click take picture icon Enter the title of the sketch. Then Go to report set
up. Select
picture Album. If you want to change the sketch title enter the title in
caption. Adjust
the picture size by adjusting height & width. Select Full page.
To export Results in word file:
File Export Report MS word file. Click save.