Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Operating Instructions
MODELS:
411-22AMO
411-221MO
411-221HMO
411-2X1MO
411-22AHMO
10070340
10070280
10070270
10070360
10070330
R
86037520 05/25/11
PRV NO. 980181
OVERVIEW
The Ninja is an electric powered carpet extractor intended for commercial use. This appliance applies a cleaning
solution to the carpet and then vacuums the soiled water back into the recovery tank.
411- X X X XXX
Designation
for domestic
115V
MO= No heater
HMO= w/ built in heat
# of vacs
2=dual
Stage of vac:
X or 3 = 3 Stg
2=2 Stg
Pressure of Pump:
A = 150 psi
1 = 100 psi
2 = 200 psi
5 = 500 psi
Warranty Registration
Thank you for purchasing a C400 product. Warranty registration is quick and easy. Your
registration will allow us to serve you better over the lifetime of the product.
To register your product go to:
www.century400.com/support/warranty/register.php
For customer assistance:
1-800-776-2436
86037520 05/25/11
TABLE OF CONTENTS
Machine Data Log/Overview................................2
Table of Contents.................................................3
HOW TO USE THIS MANUAL
How to use this Manual........................................1-1
SAFETY
Important Safety Instructions ...............................2-1
Hazard Intensity Level..........................................2-2
Safety Label Location...........................................2-3
Grounding Instructions .........................................2-4
OPERATIONS
Technical Specifications.......................................3-1
Controls ................................................................3-2
Machine Operation...............................................3-3
Pre-Run Machine Inspection ............................3-3
Equipment Set-up .............................................3-3
Priming the Pump .............................................3-3
Emptying & Cleaning Tanks..............................3-3
MAINTENANCE
Daily Maintenance................................................4-1
Periodic Maintenance...........................................4-1
Monthly Maintenance ...........................................4-1
Semi-annually ......................................................4-1
Storage.................................................................4-1
Vacuum Motor Replacement ...............................4-2
Solution Pump Replacement................................4-2
Pump Replacement Kits.......................................4-3
Machine Troubleshooting.....................................4-4
86037520 05/01/07
Maintenance
Lubrication
Vacuum Motor Replacement
Solution Pump Replacement
Troubleshooting
SERIAL # TAG
1-1
86037520 05/25/11
2-1
! WARNING
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
! CAUTION
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property
damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating
condition. Following is information that signals some potentially dangerous conditions to the operator or the
equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on
the machine. Please take the necessary steps to train the machine operating personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the
machine.
2-2
86037520 05/01/07
LABEL, WARNING
86242230
PRV NO. 500009
86037520 05/01/07
2-3
GROUNDING INSTRUCTIONS
THIS PRODUCT IS FOR COMMERCIAL USE
ONLY.
ELECTRICAL:
In the USA this machine operates on a standard 15
amp 115V, 60 hz, A.C. power circuit. The amp,
hertz, and voltage are listed on the data label found
on each machine. Using voltages above or below
those indicated on the data label will cause serious
damage to the motors.
EXTENSION CORDS:
If an extension cord is used, the wire size must be at
least one size larger than the power cord on the
machine, and must be limited to 50 feet (15.5m) in
length.
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should
malfunction or break down, grounding provides a
path of least resistance for electric current to reduce
the risk of electric shock. This appliance is equipped
with a cord having an equipment-grounding
conductor and grounding plug. The plug must be
inserted into an appropriate outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
2-4
86037520 05/01/07
TECHNICAL SPECIFICATIONS
ITEM
ELECTRICAL
Vacuum Motor
Solution Pump
MEASURE
115 volt, 60 hz
Dual 3 stage
100 psi
150 psi
10 gal (38 L)
8 gal (240 kg)
110 lbs (240 kg)
200 lbs (440 kg)
36 inches (91.44 cm)
29 inches (73.66 cm)
19.5 inches (49.53 cm)
22 feet (6.71 m)
1850 watt
Solution Capacity
Recovery Capacity
Weight- Empty
Weight-Full Solution
Height
Length
Width
Power cord
Heater
LENGTH
WIDTH
HEIGHT
BY
CENTURY 400
PUMP
VACUUM #1
VACUUM #2
86037520 04/24/09
3-1
CONTROLS
BY
CENTURY 400
3-2
1.
Pump Switch
2.
Vacuum #1 Switch
3.
Vacuum #2 Switch
86037520 05/01/07
MACHINE OPERATION
PRE-RUN INSPECTION
1. Check all fittings and connectors for proper
assembly.
2. Check all hoses for leaks. Repair or replace any
damaged hoses.
3. Check power cord(s) for any damage. If
damaged, replace.
EQUIPMENT SET-UP
1. Plug power cord from machine into properly
grounded wall outlet.
2. Turn vacuum motor switch on and off to make
sure there is electrical power at machine.
3. Connect vac hose to machine. Slide the swivel
cuff over the outlet on the tank.
4. Connect the hose to your machine and wand.
Pull back the knurled collar on the quick
disconnect coupler and push onto the connection
on the chassis. To avoid leaks, check to be that
a positive connection was made.
5. Using a clean container, fill the solution tank with
clean hot water. Mix in a non-foaming cleaning
concentrate for use in hot water extraction
machines, following the manufactures
instructions printed on container.
NOTE: When using a powder cleaner, pre-mix with
hot water in a clean container before adding to the
solution tank.
6. Turn pump and vacuum switch(s) to the on
position.
7. Start cleaning.
HEATER OPERATION
The disconnect fittings
on the heater will
become extremely hot during operation.
Allow sufficient time to cool, or run solution
through the machine with the heater turned
off before disconnecting or performing any
maintenance on the heater.
Before disconnecting the heater, open wand
valve to relieve the system of all pressure by
depressing the valve trigger.
DO NOT spray water directly on to the heater.
To clean, unplug the unit and wipe with a damp
cloth.
86037520 04/24/09
3-3
MAINTENANCE
DAILY MAINTENANCE
DO NOT attempt to repair hose! Repairing highpressure hoses may result in severe burns and
serious injury.
PERIODIC MAINTENANCE
1. Twice a month, flush a white vinegar solution
(One quart vinegar to two gallons of water) or
anti-browning solution (mixed as directed)
through the extractor, turning pump switch on/off
several times, flush with clean water. This will
prevent build-up of alkaline residue in the system.
2. Check hoses for wear, blockages, or damage.
Frayed or cracked hoses should be repaired or
replaced to eliminate vacuum or solution
pressure.
3. Check all handles, switches, knobs, electrical
cables and connections on your machine for
damage. If the cable insulation is broken or
frayed, repair or replace it immediately. Dont
take chances with electrical fire or shock.
4. Clean out solution tank. Remove and clean
solution screen.
5. Clean outside of all tanks and check for damage.
MONTHLY MAINTENANCE
1. Check all bearings for noise and wear.
2. Check all gaskets for wear and leakage.
3. Check pump pressure; observe spray pattern and
check gauge if necessary.
4. Check overall performance of machine.
SEMI-ANNUALLY
1. Check vacuum motor brushes.
STORAGE
Thoroughly clean machine if it is to be stored. You
must protect this machine from freezing while in
storage.
Make sure both recovery and solution tanks are
empty. Empty any remaining water and wipe dry.
HEAT MODELS ONLY: Be sure to thoroughly drain
water out of heater lines prior to storage in colder
climates. This heater will freeze and possibly crack
voiding your warranty.
4-1
86037520 05/01/07
MAINTENANCE
Only qualified
maintenance personnel
are to perform the following repairs.
VACUUM MOTOR REPLACEMENT
1. Turn off all switches and unplug machine.
Note:
Place
stop in
groove.
Important:
These brushes wear quicker as the length shortens due to
increased heat. Spring inside brush housing will damage
motor if brushes are allowed to wear away completely.
Important:
These brushes wear quicker as the length shortens due to
increased heat. Spring inside brush housing will damage
motor if brushes are allowed to wear away completely.
3/8 (9.5mm)
Periodically check the length of the carbon brushes. Replace
both carbon brushes when either is less than 3/8" (9.5mm)
long.
3 [9.5mm]
8
86037520 05/01/07
4-2
MAINTENANCE
FLOJET 100 PSI (86251110 PRV NO. 65219) PUMP REPLACEMENT KITS
DIAPHRAM
86235120
PRV NO. 29219
86258860
PRV NO.84166
VALVE ASM
86251090
PRV NO. 65204
PUMP HEAD
SHURFLO
86247360
PRV NO. 29219
MOTOR
4-3
Diaphragm
Diaphragm
29206
86235100
PV NO. 29206
86037520 08/03/09
Diaphragm
86235100
PV NO. 29206
TROUBLESHOOTING
PROBLEM
Loss of Power
Electrical shock
CAUSE
SOLUTION
Loss of vacuum
Carpet browning
Internal or external
solution line damaged and Replace
leaking
Jet orifice on cleaning
Total jet opening for pump should be .06 to .08
wand is to large
Internal pump components
Replace, see pump kit components (pg 4-3)
wearing out
Note: Operation of pump using a wand or hand tool with an orifice of less than .06
will cause pump to cavitate or pulsate and could result in premature wear of pump
components.
Unit not plugged in
Connect unit to 3 prong grounded outlet
Loose wiring
See dealer
Clean with steel wool. Soak in acetic acid (white
Corrosion on fittings.
vinegar). Lubricate lightly with silicone base lubricant.
Make several passes at right angles to each other.
Severe soil conditions
Use a pre-spray.
Adjust solution pressure to lower settings. Make
Over saturation
several passes without spray
Leaving carpet too wet
Check for loss of vac pressure
Too much chemical
Check label for correct solution concentration
Light carpet with no brown
Go over carpet with browning prevent only
prevention
Solution hose connection
Check for positive connection
Faulty pump
Repair or replace
Faulty floor tool valve
Repair or replace
Faulty pump switch
Repair
86037520 05/01/07
4-4
25
1
4
5
6
6
8
24
23
22
21
4
20
19
10
13
MP
PU
F
OF
ON
12
ON
CE
11
5-1
F
OF
F
OF
ON
NT
UR
C
0 IN
Y 40
4
14
15
16
10
86037520 05/01/07
18
17
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
86274040
86006700
86200010
86279190
86005640
86201300
86198460
86202230
86199600
86201290
86273830
86199430
86002450
86200670
86091030
86256960
86271380
86202250
86273810
86199200
86064950
86005670
86256200
86199540
86202160
70076
70232
140-01
87095
57030
280-03
20008
390-09A
140-05
280-02
70020
040-03
22015
500359
62900
72142
57196
040-06
70018
010-04B
08060
57040
73200
060-04A
320-05
4
4
1
10
4
2
2
1
2
11
8
2
1
1
1
3
2
2
1
1
1
1
1
1
1
DESCRIPTION
SERIAL NO.
FROM
NOTES:
86037520 05/01/07
5-2
28
1
4
5
6
6
7
27
26
25
24
23
22
10
11
MP
PU
F
OF
ON
12
ON
CE
13
F
OF
F
OF
ON
UR
NT
C
0 IN
40
4
14
15
16
10
20
19
17
18
5-3
86037520 05/01/07
21
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
86274040
86006700
86200010
86279190
86005640
86201300
86198460
86202230
86199600
86201290
86002450
86199430
86273830
86200670
86091030
86256960
86199650
86199660
86276290
86271380
86202250
86273810
86199200
86064970
86005670
86256200
86199540
86202160
70076
70232
140-01
87095
57030
280-03
20008
390-09A
140-05
280-02
22015
040-03
70020
500359
62900
72142
070-08
070-08A
70626
57196
040-06
70018
010-04B
08062
57040
73200
060-04A
320-05
4
4
1
10
4
2
2
1
2
11
1
2
8
1
1
3
1
1
4
2
2
1
1
1
2
2
2
2
DESCRIPTION
SERIAL NO.
FROM
NOTES:
86037520 05/01/07
5-4
1
2
35
36
3
38
37
4
5
9
34
33
32
10
31
4
30
11
12
17
29
18
16
28
19
12
27
20
21
13
14
22
23
15
4
5-5
86037520 05/01/07
24
26
25
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
86006700
86200010
86010630
86279190
86005640
86201300
86198460
86202230
86090790
86005810
86199600
86201290
86002450
86199430
86273830
86233480
86090930
86201880
86201840
86201860
86261300
86256960
86200560
86199650
86199660
86276290
86271380
86202250
86273810
86199200
86064960
86005670
86256200
86199540
86199530
86202160
86007010
86274040
70232
140-01
87013
87095
57030
280-03
20008
390-09A
140744
57245
140-05
280-02
22015
040-03
70020
22046
335-06
335-04
330-05
330-06
51116
72142
170-40
070-08
070-08A
70626
57196
040-06
70018
010-04B
08061
57040
73200
060-04A
060-04
320-05
70663
70076
4
1
4
10
4
2
2
1
2
4
2
11
1
2
8
1
1
1
1
1
1
3
1
1
1
4
2
2
1
1
1
2
2
1
1
2
4
4
DESCRIPTION
SERIAL NO.
FROM
NOTES:
86037520 05/01/07
5-6
PUMP GROUP
2
3
9A
9B
9C
7
6
5
5-7
86037520 05/01/07
PUMP GROUP
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
86200090
86233150
86001550
86200100
86273820
86010630
86005810
-
151-35A
20042
40043
151-35B
70019
87013
57245
OPEN
1
2
2
1
2
4
2
-
9A
86201430
250-64A
9B
86251110
65219
9C
86318630
86037520 08/03/09
SERIAL NO.
FROM
NOTES:
411-221MO
ONLY
411-221MO
ONLY
411-22AMO
ONLY
5-8
2
16A
16B
16C
14
*10
13
*11
12
7
4
6
5
8
5-9
86037520 05/01/07
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
86200090
86233150
86001550
86197290
86197360
86202130
86200120
86200110
86033590
151-35A
20042
40043
14076
31016
370-44
151-36C
151-36B
41516
1
1
1
1
1
1
1
1
1
10
86005590
56014
11
86197370
31017
12
13
14
15
86273820
86010630
86005810
-
70019
87013
57245
OPEN
2
4
2
-
16A
86201430
250-64A
16B
86251110
65219
16C
86318630
86037520 08/03/09
SERIAL NO.
FROM
NOTES:
*INCLUDED
IN ASM
*INCLUDED
IN ASM
411-22IHMO
ONLY
411-22IHMO
ONLY
411-22AHMO
ONLY
5-10
3
4
2
34
35
28
27
29
32
30
7
5
6
31
26
7
8
25
24
16
22
21
10
17
11
18
35
15
14
12
5-11
23
33
13
13
86037520 05/01/07
19
20
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
86033370
86200290
86199840
86033240
86064760
86090850
86279610
86005810
86199970
86006670
86161460
86161470
86007050
86198460
86033410
86237510
86010630
86273830
86090770
86199630
86090230
86247680
86201590
86033490
86200580
86010690
86201280
86200730
86198530
86273820
86199900
86201290
86272730
86090320
86237770
51355
260-33
090-12A
090-17
31082
065-42
87190
57245
120-08
70201
15-808123
11-800444
70683
20008
75330
35182
87013
70020
065-37
030-13
87015
56015
290-08
75345
500341
87068
280-01
065-03C
99809
70019
110-26A
280-02
66017
87257
35256
1
1
1
1
1
1
12
6
1
4
1
1
5
1
1
6
2
2
2
1
1
1
1
1
2
3
3
1
5
6
1
2
1
1
2
DESCRIPTION
SERIAL NO.
FROM
NOTES:
86037520 05/01/07
5-12
14
6
6
1
5
2
7
3
15
13
16
12
17
11
10
7
6
8
15
9
5-13
86037520 05/01/07
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
86201510
86199910
86090960
86003760
86201970
86010630
86202040
86256490
86134400
86274460
86090950
86091230
86201280
86007010
86005810
86063170
86233430
390-26
110-26B
360-23A
35166
065-92
87013
360-04A
70814
99656
70205
360-23
78463
280-01
70663
57245
39566
81431
3
1
1
2
6
12
2
3
1
1
1
1
2
3
6
1
2
DESCRIPTION
SPACER NYLON 1/4ID X 1/2OD
GASKET, VAC BRACKET
PLATE, VAC
GASKET, VAC MTR
VAC SPACER 2 1/4 II STAGE
WASHER, 1/4ID X 5/8OD SS
VACUUM MOTOR, 120V 5.7 2ST TD
STUD, 1/4-20 X 4.5 SS
DUCT, 5/8 ID SPLIT FLEX
SCR, 1/4-20 X 3/8 HHCS PLT DL
PLATE ASM, REAR VAC
TUBE, VAC EXHAUST 2.5 LONG
RIVET AL. 1/8 X 1/2
SCR, 1/4-20 X 3-1/4 HHCS PLT
NUT, 1/4-20 HEX NYLOCK SS
HOSE, VAC EXHAUST 2ID X 2 LONG
CLAMP, 2.50 WORM GEAR
86037520 05/01/07
SERIAL NO.
FROM
NOTES:
WAS 35168
5-14
14
6
6
1
5
2
7
3
15
13
16
12
17
11
10
7
6
8
15
9
5-15
86037520 05/01/07
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
86201510
86199910
86090960
86003760
86201950
86010630
86258420
86135320
86135300
86226880
86134400
86274460
86090940
86091230
86201280
86276720
86005810
86013170
86002380
390-26
110-26B
360-23A
35166
065-24E
87013
53130
140687
140676
70858
99656
70205
360-22
78463
280-01
70718
57245
39566
20046
3
1
1
2
6
12
2
3
1
1
1
1
2
3
6
1
2
DESCRIPTION
SPACER NYLON 1/4ID X 1/2OD
GASKET, VAC BRACKET
PLATE, VAC
GASKET, VAC MTR
VAC SPACER 3-1/8
WASHER, 1/4ID X 5/8OD SS
VAC MOTOR, 120V 5.7 3ST W/O TB
BRUSH SET, 120V VAC WINDSOR
BRUSH SET, 120V 3ST VAC AMETEK
STUD, 1/4-20 X 5 SS
DUCT, 5/8 ID SPLIT FLEX
SCR, 1/4-20 X 3/8 HHCS PLT DL
PLATE ASM, REAR VAC 3 STG
TUBE, VAC EXHAUST 2.5 LONG
RIVET AL. 1/8 X 1/2
SCR, 1/4-20 X 4.25 HHCS PLTD
NUT, 1/4-20 HEX NYLOCK SS
HOSE, VAC EXHAUST 2ID X 2 LONG
CLAMP, 2.25 WORM GEAR
86037520 05/01/07
SERIAL NO.
FROM
NOTES:
WAS 35168
*
*
SERVICE ONLY
SERVICE ONLY
5-16
5-17
86037520 05/01/07
86037520 05/01/07
5-18
5-19
86037520 05/01/07
NOTES
86037520 05/01/07
5-20
Product
Non-PE Parts
Service Labor
Travel
10 years
1 year
90days
None
3 years
90days
None
5 years
1 year
90days
None
90days
None
All others
UPV12 Upright Vacuum
Extractor brush motors, pump motors. ALL PC boards and electronics, ALL Vacuum motors (Except UPV12). ALL pumps carry
a one (1) year parts warranty.
Improper use of chemicals voids warranty and Century 400s liability. Defoamer is to be used in recovery tank of all Century 400
machines. Dry cleaning solvents cannot be used in any Century 400 equipment, if used fire and/or pump damage could result.
White vinegar should be pumped through the machine once each week to prevent mineral sealing.
Normal wear items and accessories including, but not limited to, carbon brushes, castors, clutches, cords, filters, finishes, gaskets,
hoses light bulbs, rectifiers, switches, squeegees, bearings, pulleys, relays, actuating cables, wheels, tires, quick disconnects, o-rings,
seals, diaphragms, thermostats, and brass fittings will be warranted for manufacturing defects for 90-days from the purchase date for
parts only.
90 day unlimited warranty:
Any equipment that fails due to a manufacturing defect within the first 90 days from date of purchase will have an unlimited warranty,
which includes parts, standard freight, and labor. Labor or freight will not be covered after 90 days from the date of purchase.
The warranty commences on the purchase date by the original end user from an authorized Century 400 agent, subject to proof of
purchase. The machine Registration Card must be completed and returned immediately at the time of purchase. If proof of purchase
cannot be identified, the warranty start date is 90 days after the date of sale to an authorized Century 400 distributor. Parts replaced or
repaired under warranty are guaranteed for the remainder of the original warranty period.
Century 400, reserves the right to change its warranty policy without notice 86039960-B PRV NO 98868 10/17/08
Century 400 Inc. 1351 W. Stanford Ave., Englewood, CO 80110 (303) 762-1800 800-444-7654 FAX (303) 865-2794
1 of 2
Century 400, reserves the right to change its warranty policy without notice 86039960-B PRV NO 98868 10/17/08
Century 400 Inc. 1351 W. Stanford Ave., Englewood, CO 80110 (303) 762-1800 800-444-7654 FAX (303) 865-2794
2 of 2