Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
com
Waterproofing
Product
Name
Application Areas
Page
No.
WPM 300
Multipurpose primer for all liquid applied membranes, moisture barrier coating, dust
suppressor & also waterproofing for potable water tanks, etc.
WPM 004
Showers, kitchens, bathrooms, wet areas and under tile protective membrane /
terrace, etc.
WPM 002
Internal and external wet areas, swimming pools, water tanks, balconies / podiums /
terrace / decks and other areas that will be tiled or otherwise protected from regular foot
traffic, etc.
WPM 124
Kitchen, toilets, balconies, wet areas, walkways, terraces, planter boxes, protected situation
like roof and decks, lift pits, etc.
WPM 415 C
Basements, retaining walls, wet areas & balcony / roof terrace areas, etc.
WPM 310
WPM 401 C
Stop active water leaks in basement, tunnels, potable water tanks and voids around
pipes, etc.
WPM 256
C 10
Shuttering oil, steel shuttering, wood shuttering & mivan shuttering, etc.
C 20
Green concrete substrates like, slabs, columns, pillars, plastering, basements & RCC, etc.
E 135
Slurry bond coat for plastering, admixture for cement sand mortar, fillets coving & bonding
agent for cold joint, etc.
EP 310
Anchoring reinforcement bars, dowels, holding down bolts, base plates, etc.
EP 300
Bonding agent for old & new concrete tiles and bricks, concrete blocks, repairing pot holes,
spalled concrete & rehabilitation structures, etc.
EP 410
B 30
Structural grout, base plates, bore packing, tie rod fixing & bulk filling in concrete repair, etc.
B 40
Repairing damaged concrete, columns and cross beams on structures, below ground
constructions, foundation support, retaining walls, etc.
B 35
Repairing and refacing internal concrete - stair treads and risers, cement and sand screeds,
concrete floors, patching concrete repair works, etc.
B 33
EP 320
Crack injection for 0.1mm-10mm, RCC walls, control joints, vertical crack injection for
concrete floors, rigid crack treatment & rehabilitation structures, etc.
EP 325
High viscous crack injection for 0.5mm -10mm, control joints, vertical crack injection for
concrete floors, RCC walls, rigid crack treatment & rehabilitation structures, etc.
SU 10
Expansion joints, crack treatments, Bond breaker, joint filler for dry walls, window
frames, etc.
AC 40
Rendered walls, bricks/masonry walls, fibre cement sheets, tilt up and pre-cast concretes,
light weight aerated concrete blocks, etc.
B 50
Industrial grout, machinery base plates, pot hole filling in industries with chemical spillages
& bore pack in chemical drains/tanks, etc.
Profile
ARDEX ENDURA (INDIA) PVT LTD is a joint venture between ARDEX Group, Germany and Prism Cement Limited, India. Both the partners
hold 50% each of the Share Capital of the Company. Initially, the Company was incorporated with the equity and technology
participation by Norcros Group based in UK. Ardex Group acquired the adhesive division of Norcros Group in 2001. As a result, AEIPL
came to be associated with ARDEX Group of Germany and the name of the Company was changed in line with this.
With the guidance & full support from the ARDEX Group, ARDEX ENDURA
remains the quality leader for the entire industry, offering excellent
building chemicals with supreme processing reliability. With manufacturing
plants at Bangalore & Baroda & with 30 active branches all over India,
ARDEX ENDURA manufactures products you can trust and rely on. Our
expert technical team is available for on-going support at every stage of
construction, from rapid response to specification writing, to installation
visits and on-site testing.
ARDEX ENDURA is the brand of choice for Architects, Engineers,
Contractors, Masons in fact for everybody associated with the Building &
Construction industries.
ARDEX
- A Global Perspective
ARDEX Global
Baustofftechnologie prsentier t
von ARDEX GmbH, Deutschland
Ludhiana
Ghaziabad
Delhi
Jaipur
Lucknow
Guwahati
Patna
Ahmedabad
Building Materials
Kolkata
Indore
Vadodara
Raipur
Bhubaneshwar
Aurangabad
Mumbai
Pune
Hyderabad
Goa
Vishakapatnam
Vijayawada
Hubli
Shimoga
Bangalore
Mangalore
Calicut
2 RUNNING PLANTS
1 UP COMING PLANT
Chennai
30 BRANCHES
Mysore
Salem
Ernakulam
Tirchy
Trivandrum
BEFORE
WATERPROOFING
SYSTEMS
FLOORING
SYSTEMS
TILE ADHESIVES
& GROUTS
AFTER
CONCRETE REPAIR
& ANCILLARIES
Waterproofing
WPM 300 Water Based Epoxy Membrane
WPM 300 is a two component water based epoxy polyamide membrane/ barrier coating.
Approved for use with potable (drinking) water, independent testing confirms conformity with the requirements of AS4020.2000 and BS6920.
Features
?
Water resistant, prevents rising damp, efflorescence
and withstands hydrostatic pressure
?
Excellent adhesion to most substrates including damp
surfaces and freshly laid green concrete
?
Safe to use in sensitive locations
Application Areas
Multipurpose primer for all liquid applied membranes, moisture barrier coating,
dust suppressor & also waterproofing for potable water tanks, etc.
Pack size
20 Litres
Part A 10 Litres
Part B 10 Litres
Coverage
Must be applied at a rate of 1.5 square metres
per litre (3.0 square metres per litre per coat)
to achieve an effective waterproofing membrane
WPM 004 Two Component Acrylic Modified Flexible Cementitious Waterproof Coating
WPM 004 is a two component waterproof coating specifically designed for under tile protective membrane and on roofs as exposed membrane.
WPM 004 is flexible, safe to use, low in odour.
The products have been uniquely formulated with special polymer to increase its strength. WPM 004 is based on the most advanced acrylic polymer
technology and is totally resistant to re-emulsification.
Features
Application Areas
Showers, kitchens, bathrooms, wet areas & under tile protective membrane /
terrace, etc.
?
Two component elastomeric waterproofing system
?
Advanced acrylic based
?
Protect the concrete from long term weathering and
resists UV rays
?
Water based - safe to use, low odour & easy cleaning
?
Suitable for all cementitious substrates
Pack size
20kg
Part A 5 litres
Part B 15kg
Coverage
Approximately 14 m per pack @ 0.8 mm - 1.0 mm
thickness for two coats by roller / brush
4kg
Part A 1 litre
Part B 3kg
Application Areas
Internal and external wet areas, swimming pools, water tanks, balconies /
podiums / terrace / decks and other areas that will be tiled or otherwise
protected from regular foot traffic, etc.
?
Rapid drying time
?
Two component undertile waterproofing membrane
?
Advanced acrylic will not re-emulsify
?
Liquid reinforced eliminates the need for reinforcing mat
?
Meets class III category for AS4858 Wet Area Membranes
Pack size
40kg
Liquid: 20 Litres
Powder: 20kg
?
Low VOC content meets Green Building Council of
Australia Green Star IEQ-13 requirements
Coverage
Two coats are recommended for an effective waterproof
membrane. One 40 kg kit will cover approximately
16 - 24m (based on two coats) depending on area
requirements between wall and floor surfaces to be
treated.
Features
?
Single component - ready to use
?
Can be applied by brush or roller
Pack Size
20kg
?
Quick drying
?
Elastomeric seamless membrane
?
Able to bridge cracks
?
Can be painted over with good quality acrylic paint
?
Water - based & Environment friendly
Coverage
Approximately 0.4 kg/m/coat (WFT) / coat
approx. 0.4 0.1mm
Waterproofing
WPM 415 C Crystalline Capillary Waterproofing
WPM 415 C is a single component polymer modified cementitious waterproofing compound. The mixed slurry as excellent adhesion with concrete / sand
cement screed. During application it seals the hairline cracks caused by shrinkage or expansion.
Features
Application Areas
Basements, retaining walls, wet areas & balcony / roof terrace areas, etc.
?
Suitable for sewage treatment and water treatment
plant, water tanks, concrete pipes and manholes
Pack size
20kg
?
Deeply penetrates and seals the substrate
?
Single component system, no addition of liquid
component except water at site
Coverage
Approximately 13 - 16.50m per two coats @ 150 - 200
microns thickness
?
Suitable for external and internal application
?
Toxic free - Providing protection against corrosive
waterborne salts
Application Areas
External walls in residential buildings, apartments buildings, hotels, malls &
commercial buildings, etc.
Pack size
15 Litres
?
Excellent workability easy, quick to apply
?
Decorative choice of colours
?
Water based safe to use, low odour and easy
cleaning
Coverage
External wall membrane application
1 x 15 litres unit will cover approximately 24 square metres
in two coats at a total dry film thickness of 0.3 mm.
Roof membrane application
1 x 15 litres unit will cover approximately 7 square metres
in two coats at a total dry film thickness of 1.0 mm.
Coverage will vary depending on the condition of the
surface and film thickness.
Application Areas
Stop active water leaks in basement, tunnels, potable water tanks and voids
around pipes, etc.
?
Water leakage stopping capability
?
Very good bonding to the cementitious substrate
Pack size
10 kg
?
Ideal for use onto horizontal / vertical surfaces and
against gravity
Yield
The yield per 10kg bag is approx. 5.50 litres.
?
Single component, add required amount of clean water
at the site
?
For internal and external situations
?
No curing required
Application Areas
Bonding Bridge, pore sealer, epoxy admixture, dust suppressor, etc.
?
Penetrating Structural Sealer
?
Forms a structural bond between new and old concrete
?
Can be applied to damp surfaces
?
Compatible with fresh cement or concrete products
?
Excellent adhesion to most substrates
PACK SIZE
20 Litres
Part A: 10 Litres
Part B: 10 Litres
Application Areas
Shuttering oil, steel shuttering, wood shuttering & mivan shuttering, etc.
?
Water based, environmentally friendly
Pack size
5 Litres
20 Litres
200 Litres
?
It reduces damage
?
Suitable for all types of shutters and moulds
?
Fast working progress
Coverage
Approximately 60 - 100 m/litre when diluted with
1 : 3 water
?
Stain free
?
Easy application
Application Areas
Green concrete substrates like, slabs, columns, pillars, plastering, basements &
RCC, etc.
?
Single component
?
Minimises the surface cracks
Pack size
5 Litres
20 Litres
200 Litres
?
Ease of curing the fresh concrete, UV exposed
concrete / mortar surface
?
Reflects UV rays
Coverage
Approximately 6m /litre /coat
?
Provides good curing efficiency
?
Toxic free and biodegradable
Features
?
High performance polymer additive for cement and
concrete mixes
Pack size
1 Litre
5 Litres
20 Litres.
?
Ideal for patching, can be feathered out to repair
cracks and also for use in coving
?
Non-toxic - does not create occupational health &
safety concerns
?
Good workability and consistency
Application Areas
Anchoring reinforcement bars, dowels, holding down bolts, base plates, etc.
?
High strength
Pack size
1kg
Part A : 250g
Part B : 750g
?
Tough, shrink-free & strong anchoring system
?
Vibration resistance
?
Resistance to heavy loads
?
Corrosion resistance
4kg
Part A : 1kg
Part B : 3kg
?
Easy to apply
Yeild
The approximate yield per 4kg pack is 2.1 litres
Application Areas
Bonding agent for old & new concrete tiles and bricks, concrete blocks, repairing
pot holes, spalled concrete & rehabilitation structures, etc.
?
Excellent bond strength
?
Non-Shrink
?
Forms a structural bond between new and old concrete
?
Can be applied to damp surfaces
?
Compatible with fresh cement or concrete products
Pack size
5kg
Part A 4kg
Part B 1kg
Coverage
Approximately 10m/kit @ 250 microns
?
Excellent adhesion to most substrates
Application Areas
Reinforcement bars, exposed rebars, exposed iron surface, etc.
?
Good adhesion to the steel reinforcement
?
Can be applied on exposed reinforcement steel surface
for use with ARDEX ENDURA repair mortors
?
Easy to apply
Pack size
5 Litres
Part A 4 Litres
Part B 1 Litre
Coverage
Approximately 4.50 m per coat/litre @ 100 micron
thickness
?
Corrosion resistant
Application Areas
Structural grout, base plates, bore packing, tie rod fixing & bulk filling in concrete
repair, etc.
?
Shrink-free
?
Strong
Pack size
25kg
?
Simply add required quantity of water
?
Can be used at flowable or pourable consistency
Yield
The approximate yield per 25kg bag + 4.5 litres of water is
13 litres
?
Chloride free
?
Non-staining
?
Can be applied by pump
?
High compressive strength
?
Excellent performance
Features
?
Suitable for electro - chemical repairs
?
Can be used without primer
Pack size
25kg
?
Excellent bond to the concrete substrate
?
Less alkali content
Yield
The approximate yield per 25kg bag + 3.9 litres of water is
12 litres
?
Good strength
?
Less permeability provides very good protection against
Carbon dioxide and chlorides
?
Can be used internal and external situations
BEFORE
AFTER
Application Areas
Repairing and refacing internal concrete - stair treads and risers, cement and
sand screeds, concrete floors, patching concrete repair works, etc.
Pack size
20.20kg
Part A 20kg
Part B 200ml
Coverage
Approximately 1 m @ 10 mm thickness
Application Areas
Repairing damaged concrete, deteriorated concrete, etc.
Pack size
20.60kg
Part A 20kg
Part B 600ml
Coverage
Approximately 1.3 m @ 10 mm thickness
Features
?
Excellent bond strength
?
High elastic modulus ensures effective transfer of
stresses at bond interface
Pack size
1kg
Part A 750g
Part B 250g
4kg
Part A 3kg
Part B 1kg
?
Pre proportioned to give consistent performance
?
Due to its low viscosity grouting can be done to
air line cracks
?
Resistant to a wide range of chemicals and liquids
Coverage
The coverage depends on the substrate, width of the crack /
void to be grouted, loss and waste and porosity of the
substrate
EP 325 Solvent Free, High Viscous Epoxy Resin for Crack Injection System
EP 325 is a two-component, moisture -insensitive, epoxy resin based crack injection system, designed for sealing cracks in concrete and restoring its
structural integrity. It is recommended for grouting of 0.5 mm to 10 mm wide cracks, cold joints and other such undesirable cracks.
Features
?
Excellent bond strength restores structural integrity
?
High elastic modulus ensures effective transfer of
stresses at bond interface
Application Areas
High viscous crack injection for 0.5mm -10mm, control joints, vertical crack
injection for concrete floors, RCC walls, rigid crack treatment & rehabilitation
structures, etc.
Pack size
5 kg
Part A 4.10kg
Part B 900gms
?
Pre proportioned to give consistent performance
?
Moisture-insensitive versatile in applications
?
Resistant to a wide range of chemicals and liquids
Coverage
The coverage depends on the substrate, width of the crack /
void to be grouted, absorption of the substrate, loss and
waste and porosity of the substrate
Application Areas
Expansion joints, crack treatments, bond breaker, joint filler for dry walls, window
frames, etc.
Pack size
Coverage
Sausage 600ml
Applicable joint length with a 600 ml Sausage (in metres)
20 sausages
per box
Joint width
Joint
(in mm)
depth
(in mm) 4 6 8
12
4
36.7 25.1 18.7 12.5
6
16.6 12.5 8.3
8
9.2 6.1
10
5.0
20
7.3
5.0
3.6
3.0
Application Areas
Rendered walls, bricks/masonry walls, fibre cement sheets, tilt up and pre-cast
concretes, light weight aerated concrete blocks, etc.
?
External anti-carbonation facade membrane
?
Semi-permeable membrane allows wall surface to
breathe
Pack size
15 Litres
?
Contains fungi and algae growth inhibitors
?
Provides excellent UV resistance and long term
protection from elements
Coverage
Coverage: 1 x 15 litre unit of AC 40 will cover
approximately 21m(at a dry film thickness of 0.35mm
after two coats).
?
Water based, safe to use, low odour and easy cleaning
Features
?
High strength
?
Resistance to heavy static loads
Pack size
Yield
26.50kg
The approximate yield per 26.50kg pack is 13.50 litres
Part A 3.30kg
Part B 1.725kg
Part C 21.475kg
?
Easy to apply
?
Shrink free, tough epoxy floor grout system
Sealing Tape
Geo Textile
BHEL, Hyderabad
Concrete Repair
Projects
Waterproofing
Projects
Valued Clientele
KPTCL, Bellary
LT Karle, Bangalore
NAL, Bangalore
Purvankara, Ernakulam
079
26425310
?
GHAZIABAD
0120 6541564
?
LUCKNOW
0522 4043251
?
SALEM
0427 2211454
?
AURANGABAD
+919881249293
?
GOA
0832 2750992
?
LUDHIANA
0161 2532170
?
SHIMOGA
08182 406022
?
BANGALORE
080
22230138
?
BHUBANESHWAR 0674 2421901
?
GUWAHATI
+917896002188
?
MANGALORE
0824 2442176
?
TRICHY
0431 6454649
?
HUBLI
0836 2236919
?
MUMBAI
022
?
TRIVANDRUM
0471 2558648
?
CALICUT
0495 2740334
?
HYDERABAD
040
?
CHENNAI
044
42805544
?
INDORE
0731 4021148
?
DELHI
011
32092369
?
ERNAKULAM
0484 2341044
27550293
65133299
?
MYSORE
0821 2570171
?
VIJAYAWADA
0866 3254587
?
PATNA
+919955542254
?
VISAKAPATNAM
0891 6469499
?
JAIPUR
0141 2392993
?
PUNE
020
?
KOLKATA
033
?
RAIPUR
0771 4038300
23452581
64781879
WPM&CRA/05/14
Branches