Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
LHG/KDT-Ne/07.04.08
Appliance Documentation
GN 19.3
GN 23.3
GN 27.3
GN 30.3
NoFrost freezer
GN 1913
GN 2313
Page 1/22
06200800SM_gb.doc
Contents
1.0
2.0
3.0
3.1
4.0
4.1
4.1.1 General.................................................................................................................................................. 5
4.1.2 Freezer compartment............................................................................................................................ 6
6.0
6.1
6.2
7.0
7.1
7.2
7.3
7.4
7.5
8.0
8.1
Disengaging the parts locking the evaporator module, folding down the evaporator module............ 15
Evaporator sensor............................................................................................................................... 16
Air sensor ............................................................................................................................................ 16
Temperature fuse................................................................................................................................ 17
Fan ...................................................................................................................................................... 17
Page 2/22
1
2
3
4
5
Freezer compartment
ON/OFF
ON/OFF button
Up/Down
Setting button higher/lower temperature
Temperature display
SuperFrost SuperFrost function
Alarm
Alarm OFF button for audible alarm
Temperature display:
Set value
Temperature range:
Temperature alarm:
Door alarm:
Audible
Fan:
Fitted
Defrosting:
Automatic
Interior light:
Not fitted
Service menu:
Fitted
Compressor:
Standard
Solenoid valve
refrigeration circuit:
Not fitted
Page 3/22
3.1
Fan
Evaporator sensor
Air sensor
Fig. 3.1 / 1
Fig. 3.1 / 2
Page 4/22
4.0
4.1
4.1.1
General
Components:
Compressor
Type:
Standard
Function:
ON:
Switch
Door switch:
Position:
In front panel
Type:
Reed contact
Activation via:
magnet on the door, magnet is replaceable.
Switching signal when:
door closed:
fan
ON
door open:
fan
door alarm
OFF
ON after 60 seconds
Loads
Fan:
Position:
Function:
Evaporator
Compressor
Door
Fan
sensor
Switch on
OFF
CLOSED
OFF
value
Switch on
ON
CLOSED
ON
value
Switch on
ON/OFF
OPEN
OFF
value
Switch off
ON/OFF
CLOSED/OPEN
OFF
value
e.g. If the evaporator sensor has reached the switch on value for the fan and the
compressor is ON and the door is closed, then the fan is ON.
Switch-on value evaporator sensor:
a) during start-up: -25C
b) In the normal mode 2K colder than air sensor
Page 5/22
Freezer compartment
Display range:
Functions
Temperature alarm:
Defrosting:
Alarm value:
-10 C
-20 C
Delay:
20 minutes
Visual:
Audible:
Door alarm:
SuperFrost:
When:
Audible:
3 beeps.
SuperFrost activated:
Cooling of the freezer compartment with full refrigeration performance (timecontrolled, 65 hours).
SuperFrost deactivated:
The appliance sets itself to the set value.
Sensors
Air sensor:
Evaporator sensor:
Position:
Function:
Position:
Function:
Page 6/22
Loads
Fan:
Position:
Function:
Evaporator
Compressor
Door
Fan
sensor
Switch on
OFF
CLOSED
OFF
value
Switch on
ON
CLOSED
ON
value
Switch on
ON/OFF
OPEN
OFF
value
Switch off
ON/OFF
CLOSED/OPEN
OFF
value
e.g. If the evaporator sensor has reached the switch on value for the fan and the
compressor is ON and the door is closed, then the fan is ON.
Switch-on value evaporator sensor:
a) during start-up: -25C
b) In the normal mode 2K colder than air sensor
Defrost heater:
Position:
Function:
Page 7/22
Compressor
Compressor:
Standard
Frame heater
Position:
4.2.2
Freezer compartment
Evaporator
Type of design:
Lamellar evaporator
Type of installation:
Injection point:
Front centre
Flow sequence:
Front to back
Page 8/22
General
5.1.1
Covers:
Front panel:
PCB carrier:
Raise and rest the front panel and disengage the PCB carrier.
Reed
Page 9/22
5.1.2
Attention:
Fig. 5.1.2 / 1
Cable clip:
Fig. 5.1.2 / 2
- Disengage the cable clip (transparent plastic clip) at the marked location.
Page 10/22
Strain relief
Fig. 5.1.2 / 3
Plug-in module:
Fig. 5.1.2 / 4
Holder for
capacitors
Fig. 5.1.2 / 5
Page 11/22
Fig. 5.1.2 / 6
Page 12/22
Disengage the cover in the marked direction and draw it forwards for removal
(Fig. 5.1.3/ 1).
Bearing pin:
Retract the adjustable foot and press the bearing pin downwards. Then swing out the
door at the bottom and draw it out of the upper bearing pin (Fig. 5.1.3/ 2).
Notch has to point forwards for re-assembly.
Notch
Fig. 5.1.3/ 1 Turn hinge cover
Spring clip:
Depress the holder and remove the spring clip. Has to be transferred to the opposite
side if the door hinges are changed (Fig. 5.1.3/ 3).
Bottom bearing part has to be transferred if the door hinges are changed (Fig. 5.1.3/ 4).
Slot:
Screw can be transferred to slot for better door adjustment (Fig. 5.1.3/ 4).
Spring clip
Slot
Holding clip
Bottom
b i
Fig. 5.1.3 / 4
Page 13/22
Magnet holder:
The holder of the door magnet is located on the top edge of the door and can be
levered off.
Magnet
Reed contact :
Reed
Page 14/22
Freezer compartment
5.2.1 Disengaging the parts locking the evaporator module, folding down the evaporator
module
Evaporator module
Locking
Locking parts:
Are snapped into place at the right and left for locking the evaporator module.
Transit support:
Lift off the polystyrene moulding first at the front, then at the back.
Draw the "top polystyrene moulding" forwards for removal.
Page 15/22
Evaporator sensor
Evaporator module:
Evaporator sensor:
Is slipped inbetween the lamellas and in case of defect it has to be cut off and repaired
with the repair kit (Art. No. 9590 062).
Temperature fuse
Evaporator
5.2.3
Air sensor
Evaporator module:
Front polystyrene moulding: Is situated behind the front panel of the evaporator module.
Acts as an air seal of the air sensor in the direction of the lamellar evaporator.
Air sensor:
Is engaged behind the front panel of the evaporator module and in case of defect it
has to be cut off and repaired with the repair kit (Art. No. 9590 062).
Page 16/22
Temperature fuse
Evaporator module:
Dismantle the evaporator module as described under 5.2.1 Disengaging the parts
locking the evaporator module.
Temperature fuse:
5.2.5
Fan
Evaporator module:
Safety plate
Fan:
Fan blade:
Press the fan blade off the fan shaft using your thumbs.
Fan:
Upper clip
Rubber mount
Fig. 5.2.5/ 1 Safety plate, fan
Page 17/22
General
Sensor values:
6.2
+35
+30
+25
+20
+15
+10
+5
0
-5
-10
-15
-20
-25
-30
-35
3.1
3.8
4.7
5.9
7.3
9.3
11.9
15.3
19.8
25.9
34.1
45.3
60.8
82.3
112.8
Freezer compartment
Wattage:
Voltage:
Speed:
Direction of rotation:
4.5
watts
230
volts
2500 rpm
right (as viewed onto shaft), left (as viewed in the direction of
the evaporator module)
Wattage:
Voltage:
Speed:
Direction of rotation:
1.9
watts
230
volts
2500 rpm
right (as viewed onto shaft), left (as viewed in the direction of
the evaporator module)
Defrost heater:
Wattage:
Voltage:
259
230
Temperature fuse:
Tripping temperature:
93C
Fan:
GN ..13
Fan:
GN ..23
watts
volts
Page 18/22
7.0
Service menu
Service menu:
Manual defrosting
Panel test
Service mode
Demo mode
No function
Service menu
Demo mode
Panel test
Service mode
Up/Down button
Manual defrosting
Menu
Opera
tion
-15C LED
1x SF
-25C LED
static
1x SF
-25C LED
flashes fast
-18C LED
-21C LED
1x SF
7.1
-15C LED:
-18C LED:
-21C LED:
-25C LED:
-32C LED:
LEDs OFF
: All OFF
-15C LED
: Compressor ON
-15C LED,
-18C LED
: Fan ON
-21C LED
: Defrost heater ON
Page 19/22
7.2
Step
Display
Operation
Display following
operation
Set value
Press
"Up/Down" and
"ON/OFF"
simultaneously for 5
seconds
Servicemenu active
Manual defrosting
selected
Manual defrosting
activated
End
Press "SF"
7.3
Step
Display
Operation
Display following
operation
SF = SuperFrost
Start service
Set value
Press
"Up/Down" and
"ON/OFF"
simultaneously for 5
seconds
Demo mode ON
2
Demo mode
seleceted
Setpoint
-18C LED
Demo mode ON
If the appliance is switched OFF and ON again when the demo mode is activated, all the temperature LEDs are lit for
3 seconds as indication of the activated demo mode.
Demo mode can be deactivated only via service menu, not by OFF/ON or disconnection from the supply.
Page 20/22
7.4
Step
Display
Operation
Display following
operation
Press
"Up/Down" and
"ON/OFF"
simultaneously for 5
seconds
Set value
Panel test -- test of sensor buttons, display elements, door sensor and beep -2
Door open/closed
and
press all buttons one after - Beep for 2 sec.
the other
- appliance switches OFF
(each operation is
confirmed by beep)
Panel test cannot be ended in step 2, for example, it has to be performed in full.
Should a button/sensor be defective, there will be no 2-second beep and the appliance will not switch OFF.
The appliance then has to be unplugged and plugged back in again.
7.5
Step
Display
Operation
Display following
operation
Set value
SF = SuperFrost
Press
"Up" and "ON/OFF" -15C LED static
Service menu active
simultaneously for 5 SuperFrost LED flashes
seconds
Power
input
6=>3
Press "Up/Down"
once
Compressor ON
---
Press "Up/Down"
once
Fan ON
4.5 watts
3<=6
End
Error code
Defective component
Emergency mode
Freezer compartment
evaporator sensor
Page 22/22