Sei sulla pagina 1di 12

Model VC

Poultry Vent Cutter

EQUIPMENT
SELECTION . . . . . . . . . . Ordering No.

TABLE OF
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . Page

Notice to Employer and Safety


Director . . . . . . . . . . . . . . . . . . . . . . . . . 2
Notice to Operators, Maintenance
and Cleanup Personnel . . . . . . . . . . . . 3
Parts Diagram and List . . . . . . . . . . . . 4
Installation Instructions . . . . . . . . . . . . 6
Specifications . . . . . . . . . . . . . . . . . . . . 7
Operation Instructions . . . . . . . . . . . . . 8
Blade / Pilot Pin Information . . . . . . . . 9
Maintenance Instructions . . . . . . . . . 10
Troubleshooting . . . . . . . . . . . . . . . . . 12

Model VC Package . . . . . . . . . . . 4302008


Model VC . . . . . . . . . . . . . . . 4302007
Balancer . . . . . . . . . . . . . . . . 1350084
Air Control Circuit . . . . . . . . 3350006
Vacuum Hose (8 ft.) . . . . . . 1323010
Air Hose Assembly . . . . . . . 1323011
Water Tube (8 ft.) . . . . . . . . 1323019
Grease (1 lb.) . . . . . . . . . . . . 1348001
Oil (1 pt.) . . . . . . . . . . . . . . . . 1348004

JARVIS
6222009::.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL. jarvis.products.corp@snet.net
TEL. 860--347--7271

FAX. 860--347--6978

WWW.jarvisproducts.com

notice to employer
and safety director

Model VC

page 2 of 12

Keep hands clear


NOTICE TO EMPLOYER AND SAFETY DIRECTOR
AVOID INJURY

1. Remove and repair any tool that malfunctions. All personnel must be instructed to remove any
malfunctioning tool.
2. Ensure that all employees who use this tool are trained in the proper use of this tool and are aware of
the dangers that may arise if they do not follow the procedures outlined in this brochure.
3. Ensure that all employees who use this tool wear a steel mesh glove at all times. Do not rely on the
steel mesh glove for safety; employees who use this tool must be instructed to keep their free hand(s)
away from the cutting edge and the cutting path of the tool.
4. Enclosed are four (4) copies of NOTICE TO OPERATORS, MAINTENANCE AND CLEANUP
PERSONNEL. Post one copy on the employees bulletin board; give one copy to the operator(s);
give one copy to the maintenance foreman; and give one copy to the sub-contract / internal cleanup
foreman. Additional copies will be provided upon request.
5. The tool is designed and intended to be powerful. This fact should be obvious to your employees, but
you must emphasize it to them.
6. Never make modifications or alterations to the tool. Replace any missing or illegible labels.
7. Ensure that proper procedures are established (in accordance with OSHAs lockout/tagout procedures
29 CFR 1910.147) to prevent accidental startup or release of stored energy.
8. Hand/Wrist/Arm injury and other Cumulative Trauma Disorders may result from repetitive work,
motion or vibration. You must make your employees aware of hazards, symptoms of injury and appropriate prevention. See OSHAs Ergonomics Program Management Guidelines for Meatpacking
Plants.
9. Follow our installation and maintenance instructions for proper installation and care of the tool.
10. Avoid injury. Do not permit the tool to be misused.
11. If you resell or distribute a Jarvis product, you must provide the purchaser with the appropriate safety
sheets and tool brochure. Additional copies of safety sheets and tool brochures will be provided upon
request.

JARVIS
6222009::.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL. jarvis.products.corp@snet.net
TEL. 860--347--7271

FAX. 860--347--6978

WWW.jarvisproducts.com

notice to operators, maintenance


and cleanup personnel

Model VC

page 3 of 12

Keep hands clear


NOTICE TO OPERATORS, MAINTENANCE AND CLEANUP PERSONNEL
REMOVE ANY MALFUNCTIONING TOOL FROM SERVICE
REPORT ANY PROBLEMS TO YOUR SUPERVISOR

1. Disconnect the air supply in accordance with OSHAs lockout/tagout procedures (29 CFR 1910.147)
before changing the blade.
2. Disconnect the air supply in accordance with OSHAs lockout/tagout procedures (29 CFR 1910.147)
before performing any repairs or maintenance.
3. Disconnect the air supply -- or have the air supply disconnected -- in accordance with OSHAs lockout/
tagout procedures (29 CFR 1910.147) before performing any cleanup.
4. Disconnect the air hose when the tool is not in use.
5. Never put fingers, hands or other parts of the body on the cutting edge of the blade or in the cutting path
of the tool.
6. Always wear a steel mesh glove on the hand that is not operating the tool. Always wear steel mesh
gloves when handling the blade.
7. Test the tool prior to use or daily. Pull the trigger and the tool should start; release the trigger and the
tool should stop. If the tool malfunctions, remove it from service and report or repair it immediately.
8. Never depress the trigger unless you want to use the tool.
9. Never make modifications or alterations to the tool. Report or replace any missing or illegible labels.

JARVIS
6222009::.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL. jarvis.products.corp@snet.net
TEL. 860--347--7271

FAX. 860--347--6978

WWW.jarvisproducts.com

parts diagram and list

Model VC

page 4 of 12

Model VC
Figure A

see page 9 for


additional blade and
pilot pin information.

ITEM
22

ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21

PART NO.
1327038
3332001
1312043
3330007
1324040
1343004
1350032
1324033
1350033
1324061
3327002
1346001
1324066
1350066
1311019
1342003
1350042
1304035
1311020
1301060
1017084

PART NAME
QTY
inch Pilot Pin
1
inch Blade
1
Cutter Shaft
1
Shaft Housing Assembly
1
Hose Connector
1
O--ring
2
Throttle Lever
1
Close Pipe Nipple
1
Lever Pivot Pin
1
Tube Connector w/Washer
1
Trigger Pin Assembly
1
Water Valve
1
Tube Connector
1
Grease Fitting
2
Needle Bearing
2
Planetary Gear
2
Rotor Vane
4
Motor End Plate (Rear)
1
Ball Bearing
1
Screw
1
Warning Label
1
3/
8
7/
8

JARVIS
6222009::.

23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

* use tool 8327001 to remove


PART NO.
PART NAME
1330042
Pistol Grip Handle
(includes items 20--23)
1317010
Hanger Ring
1327062
Trigger Retaining Pin
1343022
Gasket Seal
1303022
Split Lock Washer
1350081
Air Exhaust Muffler
1350043
Air Screen
1301092
Socket Head Cap Screw
1317012
Retaining Ring
1324017
Quick Connect Coupling
1350080
Air Inlet Valve
1327064
Valve Stem Pin
1327063
Valve Pin
1327048
Cam Retaining Pin
1349001
Trigger Cam
1338017
Trigger Bushing
1345005
Air Motor Trigger
1327046
Rotor Housing Pin
1337018
Rotor Sleeve
1312044
Splined Rotor
1304034
Motor End Plate (Front)
1311021
Ball Bearing
1303019
Washer
1311018
Needle Bearing
1312045
Gear Shaft
1327047
Planetary Gear Pin
1342004
Ring Gear
1311017
Ball Bearing
1316037
Shaft Spacer

QTY
1
1
1
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL. jarvis.products.corp@snet.net
TEL. 860--347--7271

FAX. 860--347--6978

WWW.jarvisproducts.com

parts diagram and list

Model VC

page 5 of 12

Air Control Circuit


Figure B

ITEM
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67

PART NO.
1324069
1324058
3350002
1324063
1323012
1324051
1324049
1350063
1350079
1324050
1350048
1350067
1324039
1350050
1350078
1346007
1350057
1323015
3343009

PART NAME
Tube Connector
Tube Connector
Venturi Assembly
Reducer Bushing
Tubing (9 inch)
Street Elbow
Hex Pipe Nipple
Air Regulator
Air Pilot Valve
Pipe Tee
Air Pressure Gauge
Air Regulator
Hex Soc Pipe Plug
Air Filter
Air Pilot Valve
Check Valve
Air Lubricator
Trigger Control Hose
Seal Kit for item 59

JARVIS
6222009::.

QTY
1
4
1
2
2
3
6
1
1
2
1
1
1
1
1
1
1
ft

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL. jarvis.products.corp@snet.net
TEL. 860--347--7271

FAX. 860--347--6978

WWW.jarvisproducts.com

installation instructions

Model VC

page 6 of 12

3--6 inch

Figure C

15 inch
Approx.

To Vacuum Tank:
11/2 inch Pipe min.
1/ Turn Shutoff Valve
4
To Water Supply:
1/ inch Pipe
2
1/ Turn Shutoff Valve
4

Air Control Circuit

Tie all tubes and


hoses together.

Model VC

To compressed
air supply:
1/ inch Pipe
2

To Balancer

Water Tube (1323019)


Air Hose (1323011)
Vacuum Hose (1323010)
Trigger Control Hose (1323015)

Figure D

Weld angle or
pipe to rail.

The vacuum pipe,


water pipe, air pipe
should all end at the
same height from
the floor.

Weld s hook
to angle or pipe.
Hang tool balancer from s
hook.
The tool
should be
suspended
at this level.

JARVIS
6222009::.

Trough

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL. jarvis.products.corp@snet.net
TEL. 860--347--7271

FAX. 860--347--6978

WWW.jarvisproducts.com

installation instructions
and specifications

Model VC

page 7 of 12

SPECIFICATIONS
Model VC
Operating Pressure
Air Consumption

30-60 psi

5.6-14 ft3/min 0.16--0.39 m3/min

Vacuum Requirements
Air Flow(vacuum)

Control Handle

2.0-4.1 bar

15 in Hg

50.8 kPa

ft3/min

m3/min

6--7

0.16--0.19

Blade Dia. (range)

Capacity Limited by operator skill (avg. 3000 / hour)

Single Trigger
0.75--1.75 in

19--44 mm

Blade Length (range) 0.88--3.50 in

22--89 mm

Overall Length

11.0 in

267 mm

Weight

3.2 lbs

1.45 kg

INSTALLATION INSTRUCTIONS
1 Make a bracket to suspend the Model VC and balancer. Refer to Figure D, page 6.

7.1.1 Attach the 8 ft. vacuum hose (1323010) to


the vacuum supply.

2 Install a balancer (1350084) from the bracket. Refer


to Figures C and D, page 6.

7.1.2 Attach the 8 ft. vacuum hose (1323010) to


connector (item 5).

3 Suspend the Model VC from a balancer (1350084).


Refer to Figures C and D, page 6.
4 Make the necessary vacuum connection. Refer to
Figures C and D, page 6.
5 Make the necessary water connection. Refer to Figures C and D, page 6.
6 Make the necessary air connection. Refer to Figures
C and D, page 6.
6.1 The air control circuit (3350006) must be installed in the air supply line.
6.1.1 The required compressed air supply is 14
ft3/min at 60 psi.
7 Model VC hook--up. Refer to Figure C, page 6. Refer to pages 4 and 5 for all referenced items.

6222009::.

7.2.1 Attach the 8 ft. water tube (1323019) to the


water supply.
7.2.2 Attach the 8 ft. water tube (1323019) to connector assembly (item 13).
7.3 Air:
7.3.1 Attach the air hose (1323011) to street elbow (item 56).
7.3.2 Attach the air hose (1323011) to quick connect coupling (item 31).
7.3.3 Attach trigger control hose (1323015) to
tube connector (item 51).
7.3.4 Attach trigger control hose (1323015) to
tube connector (item 10).

7.1 Vacuum:

JARVIS

7.2 Water:

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL. jarvis.products.corp@snet.net
TEL. 860--347--7271

FAX. 860--347--6978

WWW.jarvisproducts.com

operation instructions

Model VC

page 8 of 12

OPERATION INSTRUCTIONS
IMPORTANT: DISCONNECT THE AIR LINE IN ACCORDANCE WITH OSHAS LOCKOUT/TAGOUT PROCEDURES
(29 CFR 1910.147) BEFORE SHARPENING BLADES. DISCONNECT THE AIR LINE IN ACCORDANCE WITH OSHAS
LOCKOUT/TAGOUT PROCEDURES (29 CFR 1910.147) BEFORE PERFORMING ANY REPAIR OR MAINTENANCE.

6.2 With the vacuum activated, insert the pilot pin


(item 1) into the anus of the bird. The entire anus
ring should be enclosed by the blade, and the
skin of the bird should be sucked up around the
entire cutting edge of the blade. Refer to Figure
2.
Anus

Refer to pages 4 and 5 for all referenced items.

Blade

1 Attach the 8 ft. vacuum hose (1323010) to connector


(item 5).
2 Attach the 8 ft. water tube (1323019) to connector
assembly (item 13).
3 Attach the air hose (1323011) to quick connect coupling (item 31).
4 Attach trigger control hose (1323015) to tube connector (item 10).
5 Each day, before you begin operation, go through
the following checklist:
5.1 Make sure that the Model VC moves freely on
its balancer.

Anus ring

Pilot pin
Rosebud
gland
Tail

Backbone

Figure 2

Oil gland

6.3 While vacuum is holding the skin upward, pull


the trigger back fully and allow the blade to rotate. Move the blade gently forward into the bird
about 1/2 to 3/4 of the length of the blade. Do
not apply pressure on the bird until the blade is
rotating. Refer to Figures 3 and 4.
Proper Method

5.2 Make sure that you are wearing a steel mesh


safety glove on the hand that will not be operating the Model VC.
6 Making the cut:
6.1 Pull the trigger until it touches the round trigger
on the motor. This activates the vacuum at the
blade. Refer to Figure 1.
Round motor
trigger

Trigger in
rest position

Trigger in
activated
position

Figure 1

JARVIS
6222009::.

Rosebud gland
is inside of the
blade.

Improper Method

Rosebud gland
is outside of the
blade.

Skin is pulled up by
vacuum against the
cutting edge of the blade.

Figure 3
Skin is depressed
before the blade is
activated.

Figure 4

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL. jarvis.products.corp@snet.net
TEL. 860--347--7271

FAX. 860--347--6978

WWW.jarvisproducts.com

operation instructions
and blade/pilot pin information

Model VC

page 9 of 12

6.4 A gentle motion with a downward pressure will


cut the bird properly. Forcing the blade will
leave all or part of the rosebud in the bird. Do
not force the blade or stab the bird with the
blade. Do not let go of the trigger after fully depressing it. The blade will turn only a few revolutions and will shut off automatically (it will
not cut the intestines). The vacuum will remain
sucking as long as the trigger is held in the fully
depressed position.

BLADE INFORMATION (inches)


PART NO.

DIAMETER

LENGTH

3332001

7/8

1 5/8

3332002

3/4

1 5/8

6.5 The blade must always be angled toward the


center of the bird. If the blade is directed toward
either side, it will leave solid muscle attached to
the vent and this material cannot be broken loose
by hand.

3332003

3332004

1 1/4

3332005

1 1/2

3332006

7/8

2 1/2

6.6 While still holding the trigger, pull the blade


slowly out of the bird. The vacuum will hold the
anus and the fecal material long enough for the
operator to either grab the vent and move it away
from the hole or to move the vent away from the
hole with the gun.

3332008

1 1/8

3 1/2

3332009

1 1/4

3 1/2

3332010

1 3/8

3 1/2

3332011

1 1/2

3 1/2

3332015

1 1/8

6.7 Release the trigger. The vacuum will shutoff


and release the vent into the operators hand so
that it can be pulled out of the carcass and laid
gently over the side of the carcass or it will release the vent over the side of the carcass if the
vacuum pulls the vent completely out of the carcass.

3332016

1 3/8

3332026

1 3/4

2 3/4

6.8 After releasing the vent, the operator must aim


the blade at the trough before reaching the next
bird. Depress the water flush lever to flush out
all materials from the blade before attempting to
cut another bird. Do not flush waste material on
the birds. The water will not flush out the blade
unless the vacuum trigger is in the rest position.
When both vacuum and water triggers are activated, all water will be sucked up the vacuum
tube sending all waste material to the collector
tank.

1327038

3/8

1327040

1/2

2 1/2

1327041

5/16

1327052

1/2

3 1/4

1327053

3/8

2 3/4

1327054

3/8

2 1/2

1327057

3/8

3 3/4

PILOT PIN INFORMATION (inches)


PART NO.

DIAMETER

LENGTH

6.9 When a bird has fecal material on the outside of


the carcass, it can be washed off with the vent
gun before cutting the bird. Be sure that the
blade has been sufficiently flushed into the
trough before attempting to wash off any bird.
Do not attempt to wash the bird after cutting into
the carcass.

JARVIS
6222009::.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL. jarvis.products.corp@snet.net
TEL. 860--347--7271

FAX. 860--347--6978

WWW.jarvisproducts.com

maintenance instructions

Model VC

page 10 of 12

MAINTENANCE INSTRUCTIONS
IMPORTANT:

material and make it impossible to hold a


sharp edge. Return to Jarvis for regrinding.

DISCONNECT THE AIR LINE IN ACCOR-

DANCE WITH OSHAS LOCKOUT/TAGOUT PROCEDURES


(29 CFR 1910.147) BEFORE PERFORMING ANY REPAIR OR
MAINTENANCE.

Refer to pages 4 and 5 for all referenced items.

4 MODEL VC BLADE DISASSEMBLY:


Wear cut protective gloves when handling blades.

1 DAILY:
1.1 Check to see that the Model VC is getting
enough lubrication. Each one or two pulls of the
trigger should produce one drop of oil in the
sight dome. If required, adjust the oil flow.
1.2 Make sure that the oil in the lubricator is up to
the full mark. Use USDA approved Jarvis Air
Mist Lubricator Oil. Do not use mineral oil.

4.1 While holding base of blade (item 2) in place,


use special wrench (part number 8327001) to
loosen pilot pin (item 1).
4.2 Remove blade (item 2).
4.3 Inspect blade (item 2) for wear and sharpen if
necessary.
5 MODEL VC BLADE ASSEMBLY:
Wear cut protective gloves when handling blades.

2 WEEKLY:

5.1 Place blade (item 2) over cutter shaft (item 3).

2.1 Add four to five shots of grease to grease fitting


(item 14). Use USDA approved Jarvis 1315
White Grease.

5.2 Assemble pilot pin (item 1) through blade (item


2).
5.3 Tighten pilot pin (item 1) hand tight into cutter
shaft (item 3). The pilot pin will automatically
tighten with use of the tool.

3 WHEN NECESSARY:
Wear cut protective gloves when handling blades.

3.1 Sharpen the blade (item 2) when the blade becomes difficult to push into the carcass, or when
the cutting produces contamination.

6 MODEL VC DISASSEMBLY:
6.1 Follow steps and procedures 4.1 and 4.2.

3.1.1 Place a sharpening stone on the cutting


angle of the blade and activate the tool.
Continue to desired sharpness. If this action
rolls the cutting edge inward, hold a small
steel on the inside edge of the blade.

6.2 Unscrew the knurled ring on shaft housing assembly (item 4).

3.1.2 Repeat the process until the blade is sharp.

6.4 Place a pin through the cross hole in the cutter


shaft (item 3) and hit pin with a hammer on the
proper end to turn it counter--clockwise.
WARNING: pin may fly out of unit. Protect
yourself and other employees when disassembling this part.

3.1.3 If the angle of the blade becomes too short


or when the cutting edge has excessive
nicks, the blade must be reground. Do not
heat the cutting edge. Heat will anneal the

JARVIS
6222009::.

6.3 Remove shaft housing assembly (item 4). Be


careful not to lose the trigger pin assembly (item
11).

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL. jarvis.products.corp@snet.net
TEL. 860--347--7271

FAX. 860--347--6978

WWW.jarvisproducts.com

maintenance instructions

Model VC

page 11 of 12

8.5 Inspect all parts for wear and replace if necessary.

6.5 Remove the cutter shaft (item 3).


6.6 Place the Model VC in a soft jaw vise (apply
pressure only to the handle) and unscrew ring
gear (item 48).

9 GEAR SHAFT ASSEMBLY:

6.7 Remove the ring gear (item 48).

9.1 Press needle bearing (item 45) into gear shaft


(item 46).

6.8 Remove the gear shaft assembly (items 15--16,


45--47).

9.2 Insert needle bearings (item 15) into planetary


gears (item 16).

6.9 Tap on the front of pistol grip handle (item 22)


with a soft hammer (plastic lead, wood) to dislodge the motor assembly (items 17--19, 39--43).

9.3 Place bearing and gear assembly (items 15 and


16) into gear shaft (item 46) making sure that
bearing hole and gear pin hole are aligned.

6.10 Remove the motor assembly (items 17--19,


39--43). Do not lose rotor housing pin (item 39).

9.4 Press planetary gear pins (item 47) into the


threaded end of gear shaft (item 46).

6.11 Inspect all parts for wear and replace if necessary.


7 MODEL VC ASSEMBLY:
7.1 Reverse steps and procedures outlined in steps
6.1--6.10. See note below:
7.1.1 Install motor assembly with rotor housing
pin (item 39) in proper place.

10 MOTOR DISASSEMBLY:
10.1 Hold front motor end plate (item 42) while tapping on the splined end of the splined rotor (item
41) with a soft hammer (plastic, lead, wood).
10.2 Remove the front motor end plate (item 42) and
ball bearing (item 43).
10.3 Slide off rotor sleeve (item 40).
10.4 Remove vanes (items 17).

8 GEAR SHAFT DISASSEMBLY:


8.1 Press out planetary gear pin (item 47) from the
non--threaded end of gear shaft (item 46).

10.5 Press splined rotor (item 41) from rear motor


end plate (item 18).

8.2 Remove planetary gear assemblies (items 15


and 16).

10.6 Press ball bearings (items 19 and 43) out of rear


motor end plate (item 18) and front motor end
plate (item 42).

8.3 Push needle bearing (item 15) from planetary


gear (item 16).

10.7 Inspect all parts for wear and replace if necessary.

8.4 Use bearing puller (part number 1350131). Insert nut into the center of gear shaft (item 46).
Screw cap head screw into the nut until needle
bearing (item 45) is removed.

JARVIS
6222009::.

11 MOTOR ASSEMBLY:
11.1 Reverse steps and procedures outlined in steps
10.1--10.6.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL. jarvis.products.corp@snet.net
TEL. 860--347--7271

FAX. 860--347--6978

WWW.jarvisproducts.com

troubleshooting

Model VC

page 12 of 12

TROUBLESHOOTING
REMOVE ANY MALFUNCTIONING TOOL FROM SERVICE
PROBLEM
SOLUTION
MOTOR RUNS WHEN THE TRIGGER IS RELEASED.
Refer to page 4 for referenced items.

CHECK THE AIR MOTOR TRIGGER (ITEM 38).


If the trigger flops in and out or stays depressed when touched,
it is malfunctioning. Remove the air inlet valve (item 32) and
valve stem pin (item 33). With long nose pliers, remove valve
pin (item 34). Clean pins until their surfaces are smooth. Clean
out the deepest hole in the pistol grip handle (item 22) with a drill.
Rotate the drill by hand. Do not increase the size of the hole.
CHECK THE O--RING LOCATED IN AIR INLET VALVE (ITEM
32).
Remove the retaining ring, screen, spring, and poppet from the
air inlet valve (item 32). Check for an o--ring on the poppet. If
there is no o--ring on the poppet, check the inside of the air inlet
valve. Reassemble the o--ring to the poppet and reassemble the
air inlet valve.

BLADE DOES NOT ROTATE AND SHUT OFF WHEN TRIG- ADJUST AIR REGULATOR (ITEM 58).
GER IS PULLED.
Pull trigger
knob (item
58))
gg on Model VC,, and turn air regulator
g
(
Refer to page 5 for referenced items.
clockwise until the blade on the vent gun turns off. Continue to
adjust until desired number of blade rotations is accomplished.
CHECK AIR PILOT VALVE (ITEM 59).
Remove four screws and cover on air pilot valve (item 59) carefully. Check rubber diaphragm. If the rubber diaphragm has a
hole, it must be replaced (part number 3343009).
CLEAN VENTURI ASSEMBLY (ITEM 53).
If the regulator has no range of adjustment, clean the venturi assembly. Remove tube connector (item 52). Clear the small hole
in the silver pin with a small diameter wire. Do not increase the
size of the hole.
BLADE DOES NOT ROTATE WHEN TRIGGER IS PULLED.
Refer to pages 4 and 5 for referenced items.

CHECK THE AIR SUPPLY.


The air pressure gage (item 61) must show pressure.
CHECK THE VACUUM.
When trigger is pulled, there is suction at the blade. If there is
no suction at the blade, the air supply to the tool is shut off.
CHECK VANES (ITEM 17).
If air is exhausting through the butt of the pistol grip handle, release trigger and turn blade 1/2 revolution. Pull trigger. If the
Model VC runs properly now, it is an indication of sticky vanes
(causes: wrong oil, dirt in slots, lack of oil). Disassemble motor,
clean rotor, and check length of vanes (they should be .002
shorter than the length of the rotor). Check rotation of each bearing (they should rotate freely).

WATER VALVE LEAKS.


Refer to page 4 for referenced items.

WATER VALVE LEAKS AT TIME OF INSTALLATION.


Check for metal fragments from the threaded pipe. Remove water tube from tube connector (item 13). Remove tube connector
(item 13). Check water valve (item 12) for debris, and remove
debris with small pointed object. Do not damage spring or seal.
WATER VALVE LEAKS AFTER CONSIDERABLE USE.
Replace water valve (item 12).

JARVIS
6222009::.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL. jarvis.products.corp@snet.net
TEL. 860--347--7271

FAX. 860--347--6978

WWW.jarvisproducts.com

Potrebbero piacerti anche