Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
HabaCHAIN
Slat and Conveyor Chains
Product Guide
Habasit Solutions in motion
This disclaimer is made by and on behalf of Habasit and its affiliated companies, directors, employees, agents and contractors
(hereinafter collectively "HABASIT") with respect to the products referred to herein (the "Products").
SAFETY WARNINGS SHOULD BE READ CAREFULLY AND ANY RECOMMENDED SAFETY PRECAUTIONS FOLLOWED STRICTLY!
Please refer to the Safety Warnings herein, in the Habasit catalogue as well as installation and operating manuals.
All indications / information as to the application, use and performance of the Products are recommendations provided with due diligence
and care, but no representations or warranties of any kind are made as to their completeness, accuracy or suitability for a particular
purpose. The data provided herein are based on laboratory application with small-scale test equipment, running at standard conditions,
and do not necessarily match product performance in industrial use. New knowledge and experience may lead to re-assessments and
modifications within a short period of time and without prior notice.
EXCEPT AS EXPLICITLY WARRANTED BY HABASIT, WHICH WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, THE PRODUCTS ARE PROVIDED "AS IS". HABASIT DISCLAIMS ALL OTHER WARRANTIES,
EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, NON-INFRINGEMENT, OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE, ALL OF
WHICH ARE HEREBY EXCLUDED TO THE EXTENT ALLOWED BY APPLICABLE LAW. BECAUSE CONDITIONS OF USE IN INDUSTRIAL
APPLICATION ARE OUTSIDE OF HABASIT'S CONTROL, HABASIT DOES NOT ASSUME ANY LIABILITY CONCERNING THE SUITABILITY
AND PROCESS ABILITY OF THE PRODUCTS, INCLUDING INDICATIONS ON PROCESS RESULTS AND OUTPUT.
WARNING
Habasit belts and chains are made of various plastics that WILL BURN if exposed to sparks, incendiaries, open flame or excessive heat.
NEVER expose plastic belts and chains to a potential source of ignition. Flames resulting from burning plastics may emit TOXIC SMOKE
and gasses as well as cause SERIOUS INJURIES and PROPERTY DAMAGE. See the Fire Hazard Data Sheet for additional information.
Contents
Introduction
Product types
Getting started Chain selection criteria
Nomenclature
Material overview
5
6
7
12
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
37
38
39
40
41
42
44
45
46
Flexi chains
7100HA
47
Snap-on chains
843
(straight) 0.50"
843C
(straight) 0.50"
863
(straight) 0.75"
863T
(straight) 0.75"
963
(straight) 0.75"
963T
(straight) 0.75"
1843T
(radius) 0.50"
1873T
(radius) 0.75"
1873T-T (straight) 0.75"
1873-D1 (radius) 0.75"
1873-L4 (radius) 0.75"
1874T
(radius) 0.75"
3873T
(radius) 0.75"
Snap-on accessories
48
49
50
51
52
53
54
55
56
57
58
59
60
61
Multiflex chains
1700
(radius) 1.97"
1701T
(radius) 1.97"
1702
(radius) 1.97"
Multiflex accessories
62
63
64
65
Case chains
40P
(straight) 0.50"
60P
(straight) 0.75"
600
(radius) 2.50"
601
(radius) 2.50"
610T
(radius) 2.50"
611T
(radius) 2.50"
611TE
(radius) 2.50"
1100
(straight) 1.00"
1110T
(radius) 1.00"
1150
(straight) 1.50"
1151T
(radius) 1.50"
1200
(straight) 2.00"
1201AB (straight) 2.00"
1210T
(radius) 2.00"
1211TB (radius) 2.00"
1250
(straight) 2.50"
1251T
(radius) 2.50"
1400
(radius) 3.25"
1410T
(radius) 3.25"
3200
(straight) 2.00"
3210T
(radius) 2.00"
NH78
(straight) 2.61"
Case chain accessories
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
4185BRO.CHA-en1115HQR
Contents
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
Split sprockets
1061 Sprockets
120
Retainer rings
Retainer rings
121
Appendix
Chemical resistance Plastics
Chemical resistance Steel
Safety information
The Habasit solution
122
127
128
130
4185BRO.CHA-en1115HQR
Product types
Flexi chains
For standardized modular
conveyor systems made of
aluminum or steel profiles.
Snap-on chains
Two-piece chain with steel roller base
chain and plastic top plate. Base
chains in two dimensions (ANSI 40 =
0.5" pitch or ANSI 60 = 0.75" pitch)
and made of carbon or stainless steel.
Multiflex chains
The 1700, 1701T and 1702 are heavy
duty biplanar chains. Applications
include alpine systems (inline
accumulation) and case conveyors.
Case chains
Case chains are available in many
different designs ranging from
0.5" pitch to 3.25" pitch. The
popular 1200/3200 series chain was
developed and patented.
Split sprockets
Machined split sprockets
Retainer rings
For lateral fixation of sprockets and
idlers on round and square shafts.
4185BRO.CHA-en1115HQR
Getting started
Chain selection criteria
Chain material
HabaCHAIN offers a variety of different materials to
meet specific application requirements. Some of these
are only available on request.
Pin material
Stainless steel pins are available in magnetic and nonmagnetic alloys.
Chain color
For standard colors please refer to the Material
Overview. Other colors are available on request.
Sprockets and idlers
Multi-Hub and Solid types are available.
HabaCHAIN
Slat Top 820 (Straight)
18
Product type
Drawing: indicates
the main dimensions
(characters/figures are
displayed in the data
chart below)
Description
Photo:
Straightproduct
running plastic
chain
is
shown
820 hinge
design
=
identical
sprocket for 820 and 831 series chains
in the most
common
For side transfer
with(in
770, 880 or 890 series radius running chains
material
Habasit code
(descriptive)
Rb = Backbending radius
Rs = Sideflexing radius
Ra = Top plate roughness
Chain data
Habasit code
Width W
Weight
Material
mm
inch
kg/m
lb/ft
lbf
C0820K0250DPAA
63.5
2.50
0.74
0.50
1650
371
C0820K0250LFAA
63.5
2.50
0.74
0.50
1650
371
LF
C0820K0250PTAA
63.5
2.50
0.74
0.50
1650
371
PT
DP
Nomenclature
Chain code
Chain type
Version: B = Snap-on base chain, J = Carbon steel pin, K = AISI 430/431 pin, L = PA pin,
N = PBT pin, M = Magnetic, P = AISI 304 pin, Q = AISI 316 pin, S = Snap-on, U = Single link
Chain width: (or pitch for base chains or connecting links)
Material: (see material overview)
Link design: A = Standard, T = Tab, B = Bevel,
P = Multi-Hinge, J = Special bevel, H = Heavy duty,
K = No backbending
Style: A = Standard, G = GripTop, F = Flight,
R = Low back pressure, S = Sliding block,
W = Wave Top, C = Curve Top, P = Pusher,
E = Modified tab
Extensions
10
11
12
13
14
15
16
17
18
Extensions
Type: digits 16 and 17
WG Wide gap hinges L4 Four finger GripTop D1 Tubular GripTop R1 Bent right L1 Bent left,
RL Bent both sides T 1873T-T TP Snap-on top plate
Building pattern for chains with accessories: digits 16 and 17
01 Accessory on each module
02 Accessory on every second module per 10 ft
03 Accessory on every third module per 10 ft
04 Accessory on every fourth module per 10 ft
Colors (on request): digit 18
. . 1 White . . 2 Gray . . 3 Blue . . 4 Black . . 8 Dark gray . . 9 Natural . . A Green
. . N Granite
Examples
C0882K0750PTTR
Chain 882 Version AISI 430 pin Width 7.50 inch Material PT Link design Tab
Style Low back pressure
C0810J0325CSAA-WG
Chain 810 Version Carbon steel pin Width 3.25 inch Material CS Link design Standard
Style Standard Extension Wide gap hinges
C1873S0375LFTG-D1
Chain 1873 Version Snap-on Width 3.75 inch Material LF Link design Tab
Style GripTop Extension Tubular GripTop
4185BRO.CHA-en1115HQR
Nomenclature
Multi-Hub inserts
Chain type
Shaft diameter
Shaft type: R = Round
Type: G = Sprocket, L = Idler
Material: GS = 8,
ND = 7, L = 9
Material: GS = 8,
ND = 7, L = 9
Extensions
Extensions
10
11
12
10
Examples
C0820G257
Chain 820 or similar engagement Type Multi-Hub Sprocket rim Teeth 25
Material Special noise dampening material
C0820L219
Chain 820 or similar engagement Type Multi-Hub Idler-Rim Teeth 21 Material L
H030RZ-8
Multi-Hub Insert Shaft diameter 30 mm Shaft type Round Type Drive Material GS
H100RL-9
Multi-Hub Insert Shaft diameter 1.00 inch Shaft type Round Type Idler Material L
4185BRO.CHA-en1115HQR
Nomenclature
10
11
12
13
14
15
16
17
18
Square shape
Code
Diameter
Code
Diameter
Code
Diameter
Code
Width
Code
Width
00
Pilot bore
50
50 mm
32
1.25"
25
25 mm
02
1"
20
20 mm
60
60 mm
37
1 7/16"
40
40 mm
03
1.5"
25
25 mm
90
90 mm
03
1.5"
50
50 mm
04
2"
60
60 mm
05
2.5"
30
30 mm
01
0.75"
04
2"
35
35 mm
02
1"
05
2.5"
40
40 mm
31
1 3/16
07
3.5"
Extensions
Colors (on request): digit 18
. . 1 White . . 4 Black
Examples
C0810L19PE
Chain 810 or similar engagement Type Idler Teeth 19 Material PE
C3200M08PE03QC
Chain 3200 or similar engagement Type Machined Sprocket Teeth 08 Material PE Bore size 1.5 inch
Bore shape Square Hub type C
4185BRO.CHA-en1115HQR
Nomenclature
10
Accessories code
Chain type
Version: B = Snap-on base chain, J = Carbon steel pin, K = AISI 430/431 pin, L = PA pin,
N = PBT pin, M = Magnetic, P = AISI 304 pin, Q = AISI 316 pin, S = Snap-on, U = Single link
Chain width: (special code only for accessories see below)
Accessories: (see code below)
Material: (see material overview)
Link design: A = Standard, T = Tab B = Bevel P = MultiHinge, J = Special bevel, H = Heavy duty, K = No backbending
Style: A = Standard, G = GripTop, F = Flight, R =
Low back pressure, S = Sliding block, W = Wave
Top, C = Curve Top, P = Pusher, E = Modified tab
Extensions
10 11 12 13
14
15
16
17
18
19
Description
Code
Description
Code
Description
Code
Description
100
125
138
1.00"
1.25"
1.38"
210
219
224
2.10"
2.19"
2.24"
330
375
400
3.30"
3.75"
4.00"
Q12
Q15
Q16
12.00"
15.00"
16.00"
144
1.44"
225
2.25"
405
4.05"
150
1.50"
248
2.48"
450
4.50"
165
1.65"
250
2.50"
600
6.00"
169
1.69"
291
2.91"
750
7.50"
200
2.00"
325
3.25"
Q10
10.00"
4185BRO.CHA-en1115HQR
Nomenclature
11
Examples
C0820K325XAPTAA-05
Chain 820 Version AISI 430 pin Width 3.25 inch Accessory Custom insert type A
Material PT Link design Standard Style Standard
Extension Accessory on every fifth module per 10 ft
C1873SQ12XBLFTA-11
Chain 1873 Version Snap-on Width 12.00 inch Accessory Custom insert type B
Material LF Link design Tab Style Standard
Extension Accessory on every 11th module per 10 ft
C1200P224K2DPAA-031
Chain 1200 Version AISI 304 pin Width 2.24 inch Accessory Plastic tab two holes (two sides)
Material DP Link design Standard Style Standard
Extension Accessory on every third module per 10 ft and color white
CNH78P291EPLFAA-157
Chain NH78 Version AISI 304 pin Width 2.91 inch Accessory Extended pin
Material LF Link design Standard Style Standard
Extension Accessory on every 15th module per 10 ft and pin diameter 7/16 inch
C7100T325
Chain 7100 Version Pin tool Width 3.25 inch
4185BRO.CHA-en1115HQR
Material overview
12
Plastic chains
HabaCHAIN products are made of high quality plastics from the best raw material producers. Habasits
program of studying material applications ensures the most suitable plastic type material for the particular
conditions, as listed below:
Plastic chains Standard chain materials
Material
DP
Density
[g/cm3]
Description
1.42
1)
LF
1.42
PT
1.43
TS
1.43
NG
Extra low friction PBT material with good strength and very
good abrasion resistance.
Suitable for high speed, dry running applications. Should be
used in combination with a high performance corner track.
1.34
Temperature range
Dry conditions:
-40 C to +93 C
(-40 F to +200 F)
Wet conditions:
-40 C to +60 C
(-40 F to +140 F)
Dry conditions:
-40 C to +93 C
(-40 F to +200 F)
Wet conditions:
-40 C to +60 C
(-40 F to +140 F)
Dry conditions:
-40 C to +93 C
(-40 F to +200 F)
Wet conditions:
-40 C to +60 C
(-40 F to +140 F)
Dry conditions:
-40 C to +93 C
(-40 F to +200 F)
Wet conditions:
-40 C to +60 C
(-40 F to +140 F)
Dry conditions:
-40 C to +120 C
(-40 F to +248 F)
Wet conditions:
-40 C to +50 C
(-40 F to +122 F)
Standard
color
Gray
Light
brown
for Flexi
Chains:
White
Graybrown
for Flexi
Chains:
White
Silver
Gray
Description
Density
[g/cm3]
Temperature range
Standard
color
For special materials, strength reduction and dimensional variation to be expected. Please consult with Habasit Engineering.
1)
PK
EC
1.41
Dry conditions:
-40 C to +93 C
(-40 F to +200 F)
Wet conditions:
-40 C to +66 C
(-40 F to +151 F)
Dark gray
1.42
Dry conditions:
-40 C to +93 C
(-40 F to +200 F)
Black
POM (Acetal) generally shows good resistance to oil and alkalines and has a cut-resistant surface.
4185BRO.CHA-en1115HQR
Material overview
13
Description
Density
[g/cm3]
Temperature range
Dry conditions:
-40 C to +93 C
(-40 F to +200 F)
Wet conditions:
-40 C to +66 C
(-40 F to +151 F)
Dry conditions:
-46 C to +118 C
short-term +135 C
(-50 F to +245 F
short-term +275 F)
Wet conditions:
not recommended
Dry conditions:
-18 C to +82 C
(0 F to +180 F)
Wet conditions:
not recommended
Dry conditions:
-40 C to +145 C
short-term +175 C
(-40F to +293 F
short-term +347 F)
Wet conditions:
not recommended
Dry conditions:
-40 C to +120 C
(-40 F to +248 F
Wet conditions:
-40 C to +50 C
(-40 F to +122 F)
Standard
color
DE
1.67
NY
1.14
WR
1.35
HT
1.37
NP
1.30
PP
1.13
+5 C to +105 C
(+40 F to + 220 F)
Natural
white
CR
1.78
Dry conditions:
+5 C to +115 C
(+40 F to +239 F)
Wet conditions:
+5 C to +115 C
(+40 F to +239 F)
White
Blue
Dark gray
Black
Black
Natural
white
4185BRO.CHA-en1115HQR
Material overview
14
Steel chains
Material
Description
Density
[g/cm3]
CS
7.85
SS
7.90
SH
7.70
SA
7.90
Description
Density
[g/cm3]
Temperature range
Wet conditions:
not recommended
Dry conditions:
-40 C to +180 C
(-40 F to +355 F)
Dry conditions:
-40 C to +260 C
(-40 F to +500 F)
Wet conditions:
-40 C to +120 C
(-40 F to +248 F)
Dry conditions:
-40 C to +260 C
(-40 F to + 500 F)
Wet conditions:
-40 C to +120 C
(-40 F to +248 F)
Dry conditions:
-40 C to +400 C
(-40 F to +752 F)
Wet conditions:
-40 C to +120 C
(-40 F to +248 F)
Standard
color
Black
Gray
Gray
Gray
Pins
Material
7.85
7.90
7.90
High chemical resistance - Austenitic stainless steel, nonmagnetic with increased resistance to chloride corrosion.
AISI 316 (Previous code IN)
7.90
Temperature range
Wet conditions:
not recommended
Dry conditions:
-40 C to +180 C
(-40 F to +355 F)
Dry conditions:
-40 C to +260 C
(-40 F to +500 F)
Wet conditions:
-40 C to +120 C
(-40 F to +248 F)
Dry conditions:
-40 C to +400 C
(-40 F to +752 F)
Wet conditions:
-40 C to +120 C
(-40 F to +248 F)
Dry conditions:
-40 C to +400 C
(-40 F to +752 F)
Wet conditions:
-40 C to +120 C
(-40 F to +248 F)
Standard
color
Gray
Gray
Gray
Gray
4185BRO.CHA-en1115HQR
Material overview
15
Pins
Material
Description
Density
[g/cm3]
1.55
Extra low friction PBT material with good strength and very
good abrasion resistance.
Easy to recycle for selected plastic chains. (Previous code
NG)
1.30
Description
Density
[g/cm3]
Temperature range
Dry conditions:
-40 C to +145 C
short-term +175 C
(-40F to +293 F
short-term +347 F)
Wet conditions:
not recommended
Dry conditions:
-40 C to +120 C
(-40 F to +248 F
Wet conditions:
-40 C to +50 C
(-40 F to +122 F)
Standard
color
Natural
beige
Natural
white
Sprockets
Material
GS
ND
PE
1.37
1.24
0.94
NY
1.14
1.41
CI
7.85
Temperature range
Dry conditions:
-46 C to +118 C
(-50 F to +245 F
Wet conditions:
-40 C to +50 C
(-40 F to +122 F)
-20 C to +50 C
(-4 F to + 120 F)
-70 C to +65 C
(-94 F to +150 F)
Dry conditions:
-46 C to +118 C
short-term +135 C
(-50 F to +245 F
short-term +275 F)
Wet conditions:
not recommended
Dry conditions:
-40 C to +93 C
(-40 F to +200 F)
Wet conditions:
-40 C to +60 C
(-40 F to +140 F)
Dry conditions:
-40 C to +180 C
(-40 F to +355 F)
Wet conditions:
not recommended
Standard
color
Black
Dark gray
Natural
white
Natural
white
Black
Black
Accessories
Material
Description
Density
[g/cm3]
1.16
PL
1.14
HY
1.20
PP
1.13
Temperature range
-40 C to +60 C
(-40 F to +140 F)
-40 C to +80 C
(-40 F to +176 F)
-40 C to +110 C
(-40 F to +230 F)
+5 C to +105 C
(+40 F to +220 F)
Standard
color
Black or
White
Black or
White
Black or
white
Blue
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 770T (radius)
16
Description
Chain data
Habasit code
C0770K0325LFTA
C0770K0325PTTA
C0770K0325TSTA
Width W
Weight
mm
inch
kg/m
lb/ft
82.6
82.6
82.6
3.25
3.25
3.25
1.12
1.12
1.12
0.75
0.75
0.75
Nominal tensile
strength FN
N
lbf
1500
1500
1500
337
337
337
J (straight)
J (curve)
Rs
Material
mm
inch
mm
inch
mm
inch
46.0
46.0
46.0
1.81
1.81
1.81
44.5
44.5
44.5
1.75
1.75
1.75
260
260
260
10.2
10.2
10.2
LF
PT
TS
Related products
Multi-Hub 1060 sprocket rims
Multi-Hub inserts
Split sprockets Series 1061
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 820 (straight)
17
Description
Straight running plastic chain
820 hinge design = identical sprocket for 820 and 831 series chains
For side transfer with 770, 880 or 890 series radius running chains
Chain data
Habasit code
C0820K0250DPAA
C0820K0250LFAA
C0820K0250PTAA
C0820K0325DPAA
C0820K0325LFAA
C0820K0325PTAA
C0820K0400DPAA
C0820K0400LFAA
C0820K0400PTAA
C0820K0450DPAA
C0820K0450LFAA
C0820K0450PTAA
C0820K0600DPAA
C0820K0600LFAA
C0820K0600PTAA
C0820K0750DPAA
C0820K0750LFAA
C0820K0750PTAA
Width W
mm
63.5
63.5
63.5
82.6
82.6
82.6
101.6
101.6
101.6
114.3
114.3
114.3
152.4
152.4
152.4
190.5
190.5
190.5
Weight
inch
2.50
2.50
2.50
3.25
3.25
3.25
4.00
4.00
4.00
4.50
4.50
4.50
6.00
6.00
6.00
7.50
7.50
7.50
kg/m
0.74
0.74
0.74
0.85
0.85
0.85
0.95
0.95
0.95
1.03
1.03
1.03
1.25
1.25
1.25
1.47
1.47
1.47
lb/ft
0.50
0.50
0.50
0.57
0.57
0.57
0.64
0.64
0.64
0.69
0.69
0.69
0.84
0.84
0.84
0.99
0.99
0.99
Material
DP
LF
PT
DP
LF
PT
DP
LF
PT
DP
LF
PT
DP
LF
PT
DP
LF
PT
Options
Plastic pin
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 821 (straight)
18
Description
Chain data
Habasit code
C0821K0750DPAA
C0821K0750LFAA
C0821K0750PTAA
C0821K1000DPAA
C0821K1000LFAA
C0821K1000PTAA
C0821K1200DPAA
C0821K1200LFAA
C0821K1200PTAA
Width W
mm
190.5
190.5
190.5
254.0
254.0
254.0
304.8
304.8
304.8
Weight
inch
7.50
7.50
7.50
10.00
10.00
10.00
12.00
12.00
12.00
kg/m
2.60
2.60
2.60
3.10
3.10
3.10
3.40
3.40
3.40
lb/ft
1.75
1.75
1.75
2.08
2.08
2.08
2.28
2.28
2.28
Material
DP
LF
PT
DP
LF
PT
DP
LF
PT
Related products
Multi-Hub 821 sprocket rims (2 set-up side-by-side)
. Multi-Hub inserts
Solid sprockets Series 821
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 828 (straight)
19
Description
Straight running plastic chain
880 hinge design = identical sprocket for 828, 879, 880, 890 series chains
For side transfer with 770, 880 or 890 series radius running chains
Chain data
Habasit code
C0828K0330LFAA
Width W
mm
83.8
Weight
inch
3.30
kg/m
0.89
lb/ft
0.60
Material
LF
Related products
Multi-Hub 880 sprocket rims
Multi-Hub 820 idler rims
Multi-Hub inserts
Solid sprockets Series 880
Solid idler 810
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 831 (straight)
20
Description
Chain data
Habasit code
C0831K0325DPAA
C0831K0325LFAA
C0831K0325PTAA
C0831K0450DPAA
C0831K0450LFAA
C0831K0450PTAA
C0831K0750DPAA
C0831K0750LFAA
C0831K0750PTAA
Width W
mm
82.6
82.6
82.6
114.3
114.3
114.3
190.5
190.5
190.5
Weight
inch
3.25
3.25
3.25
4.50
4.50
4.50
7.50
7.50
7.50
kg/m
1.00
1.00
1.00
1.30
1.30
1.30
1.82
1.82
1.82
lb/ft
0.67
0.67
0.67
0.87
0.87
0.87
1.22
1.22
1.22
Material
DP
LF
PT
DP
LF
PT
DP
LF
PT
Related products
Multi-Hub 820 sprocket rims
Multi-Hub 820 idler rims
Multi-Hub inserts
Solid sprockets Series 820
Solid idlers Series 810
Options
Plastic pin
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 879B (radius)
21
Description
Chain data
Habasit code
C0879K0325DPBA
C0879K0325LFBA
C0879K0325PTBA
C0879K0450DPBA
C0879K0450LFBA
C0879K0450PTBA
C0879K0750DPBA
C0879K0750LFBA
C0879K0750PTBA
Width W
mm
82.6
82.6
82.6
114.3
114.3
114.3
190.5
190.5
190.5
inch
3.25
3.25
3.25
4.50
4.50
4.50
7.50
7.50
7.50
Weight
kg/m
1.00
1.00
1.00
1.25
1.25
1.25
1.92
1.92
1.92
lb/ft
0.67
0.67
0.67
0.84
0.84
0.84
1.29
1.29
1.29
Nominal tensile
strength FN
N
lbf
1900
428
1900
428
1900
428
1900
428
1900
428
1900
428
1900
428
1900
428
1900
428
J (straight)
mm
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
inch
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
J (curve)
mm
41.3
41.3
41.3
41.3
41.3
41.3
41.3
41.3
41.3
inch
1.62
1.62
1.62
1.62
1.62
1.62
1.62
1.62
1.62
Rs
mm
457
457
457
500
500
500
610
610
610
Material
inch
18.0
18.0
18.0
19.7
19.7
19.7
24.0
24.0
24.0
DP
LF
PT
DP
LF
PT
DP
LF
PT
Related products
Multi-Hub 880 sprocket rims
Multi-Hub 820 idler rims
Multi-Hub inserts
Solid sprockets Series 880
Solid idlers Series 810
Options
Plastic pin
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 879T (radius)
22
Description
Chain data
Habasit code
C0879K0325DPTA
C0879K0325LFTA
C0879K0325PTTA
C0879K0450DPTA
C0879K0450LFTA
C0879K0450PTTA
C0879K0750DPTA
C0879K0750LFTA
C0879K0750PTTA
Width W
mm
82.6
82.6
82.6
114.3
114.3
114.3
190.5
190.5
190.5
inch
3.25
3.25
3.25
4.50
4.50
4.50
7.50
7.50
7.50
Weight
kg/m
1.06
1.06
1.06
1.30
1.30
1.30
1.98
1.98
1.98
lb/ft
0.71
0.71
0.71
0.87
0.87
0.87
1.33
1.33
1.33
Nominal tensile
FN
N
1900
1900
1900
1900
1900
1900
1900
1900
1900
strength
lbf
428
428
428
428
428
428
428
428
428
Rs
mm
457
457
457
500
500
500
610
610
610
Material
inch
18.0
18.0
18.0
19.7
19.7
19.7
24.0
24.0
24.0
DP
LF
PT
DP
LF
PT
DP
LF
PT
Related products
Multi-Hub 880 sprocket rims
Multi-Hub inserts
Solid sprockets Series 880
Options
Plastic pin
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 880B (radius)
23
Description
Radius running plastic bevel chain
880 hinge design = identical sprocket for 828, 879, 880, 890 series chains
For side transfer with 820 and 828 series straight running chains
Chain data
Habasit code
C0880K0325DPBA
C0880K0325LFBA
C0880K0325PTBA
C0880K0450DPBA
C0880K0450LFBA
C0880K0450PTBA
C0880K0750DPBA
C0880K0750LFBA
C0880K0750PTBA
Width W
mm
82.6
82.6
82.6
114.3
114.3
114.3
190.5
190.5
190.5
inch
3.25
3.25
3.25
4.50
4.50
4.50
7.50
7.50
7.50
Weight
kg/m
0.89
0.89
0.89
1.04
1.04
1.04
1.40
1.40
1.40
lb/ft
0.60
0.60
0.60
0.70
0.70
0.70
0.94
0.94
0.94
Nominal tensile
strength FN
N
lbf
1900
428
1900
428
1900
428
1900
428
1900
428
1900
428
1900
428
1900
428
1900
428
J (straight)
mm
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
inch
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
J (curve)
mm
41.3
41.3
41.3
41.3
41.3
41.3
41.3
41.3
41.3
inch
1.62
1.62
1.62
1.62
1.62
1.62
1.62
1.62
1.62
Rs
mm
457
457
457
500
500
500
610
610
610
Material
inch
18.0
18.0
18.0
19.7
19.7
19.7
24.0
24.0
24.0
DP
LF
PT
DP
LF
PT
DP
LF
PT
Related products
Multi-Hub 880 sprocket rims
Multi-Hub 820 idler rims
Multi-Hub inserts
Solid sprockets Series 880
Solid idlers Series 810
Options
Plastic pin
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 880LJ (radius)
24
Description
Chain data
Habasit code
C0880L0325LFJA-00A
Width W
mm
82.6
inch
3.25
Weight
kg/m
0.70
lb/ft
0.47
Nominal tensile
strength FN
N
lbf
1050
236
J (straight)
mm
43
inch
1.69
J (curve)
mm
40.5
inch
1.59
Rs
mm
600
Material
inch
23.6
LF
Related products
Multi-Hub 880 sprocket rims
Multi-Hub 820 idler rims
Multi-Hub inserts
Solid sprockets Series 880
Solid idler 810
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 880J (radius)
25
Description
Chain data
Habasit code
C0880K0325LFJA
C0880K0450LFJA
Width W
mm
82.6
114.3
inch
3.25
4.50
Weight
kg/m
0.89
1.04
lb/ft
0.60
0.70
Nominal tensile
strength FN
N
lbf
1900
428
1900
428
J (straight)
mm
44.5
44.5
inch
1.75
1.75
J (curve)
mm
41.3
41.3
inch
1.62
1.62
Rs
mm
457
500
Material
inch
18.00
19.70
LF
LF
Related products
Multi-Hub 880 sprocket rims
Multi-Hub 820 idler rims
Multi-Hub inserts
Solid sprockets Series 880
Solid idler 810
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 880T (radius)
26
Description
Radius running plastic tab chain
880 hinge design = identical sprocket for 828, 879, 880, 890 series chains
For side transfer with 820 and 828 series straight running chains
Chain data
Habasit code
C0880K0325DPTA
C0880K0325LFTA
C0880K0325PTTA
C0880K0450DPTA
C0880K0450LFTA
C0880K0450PTTA
C0880K0750DPTA
C0880K0750LFTA
C0880K0750PTTA
Width W
mm
82.6
82.6
82.6
114.3
114.3
114.3
190.5
190.5
190.5
inch
3.25
3.25
3.25
4.50
4.50
4.50
7.50
7.50
7.50
Weight
kg/m
1.00
1.00
1.00
1.16
1.16
1.16
1.35
1.35
1.35
lb/ft
0.67
0.67
0.67
0.74
0.74
0.74
0.99
0.99
0.99
Nominal tensile
FN
N
1900
1900
1900
1900
1900
1900
1900
1900
1900
strength
lbf
428
428
428
428
428
428
428
428
428
Rs
mm
457
457
457
500
500
500
610
610
610
Material
inch
18.0
18.0
18.0
19.7
19.7
19.7
24.0
24.0
24.0
DP
LF
PT
DP
LF
PT
DP
LF
PT
Related products
Multi-Hub 880 sprocket rims
Multi-Hub inserts
Solid sprockets Series 880
Options
Plastic pin
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 880M (radius)
27
Description
Chain data
Habasit code
C0880M0325DPAA
C0880M0325LFAA
C0880M0325PTAA
C0880M0330DPAA
C0880M0330LFAA
C0880M0330PTAA
C0880M0450DPAA
C0880M0450LFAA
C0880M0450PTAA
Width W
mm
82.6
82.6
82.6
83.8
83.8
83.8
114.3
114.3
114.3
inch
3.25
3.25
3.25
3.30
3.30
3.30
4.50
4.50
4.50
Weight
kg/m
0.90
0.90
0.90
0.91
0.91
0.91
1.07
1.07
1.07
lb/ft
0.62
0.62
0.62
0.61
0.61
0.61
0.72
0.72
0.72
Nominal tensile
FN
N
1900
1900
1900
1900
1900
1900
1900
1900
1900
strength
lbf
428
428
428
428
428
428
428
428
428
Rs
mm
457
457
457
457
457
457
500
500
500
Material
inch
18.0
18.0
18.0
18.0
18.0
18.0
19.6
19.6
19.6
DP
LF
PT
DP
LF
PT
DP
LF
PT
Related products
Multi-Hub 880 sprocket rims
Multi-Hub 820 idler rims
Multi-Hub inserts
Solid sprockets Series 880
Solid idler 810
Magnetic corner tracks see HabiPLAST Product Guide Code No. 4097
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 882B (radius)
28
Description
Radius running plastic bevel chain
Thick top plate = longer wear life
Chain data
Habasit code
C0882K0450DPBA
C0882K0450LFBA
C0882K0450PTBA
C0882K0750DPBA
C0882K0750LFBA
C0882K0750PTBA
C0882K1000DPBA
C0882K1000LFBA
C0882K1000PTBA
C0882K1200DPBA
C0882K1200LFBA
C0882K1200PTBA
Width W
mm
114.3
114.3
114.3
190.5
190.5
190.5
254.0
254.0
254.0
304.8
304.8
304.8
inch
4.50
4.50
4.50
7.50
7.50
7.50
10.00
10.00
10.00
12.00
12.00
12.00
Weight
kg/m
1.79
1.79
1.79
2.20
2.20
2.20
2.52
2.52
2.52
2.75
2.75
2.75
lb/ft
1.20
1.20
1.20
1.48
1.48
1.48
1.69
1.69
1.69
1.85
1.85
1.85
Nominal tensile
strength FN
N
lbf
2850
641
2850
641
2850
641
2850
641
2850
641
2850
641
2850
641
2850
641
2850
641
2850
641
2850
641
2850
641
J (straight)
mm
62
62
62
62
62
62
62
62
62
62
62
62
inch
2.44
2.44
2.44
2.44
2.44
2.44
2.44
2.44
2.44
2.44
2.44
2.44
J (curve)
mm
58
58
58
58
58
58
58
58
58
58
58
58
inch
2.28
2.28
2.28
2.28
2.28
2.28
2.28
2.28
2.28
2.28
2.28
2.28
Rs
mm
610
610
610
610
610
610
610
610
610
610
610
610
Material
inch
24.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
DP
LF
PT
DP
LF
PT
DP
LF
PT
DP
LF
PT
Related products
Multi-Hub 882 sprocket rims
Multi-Hub inserts
Solid sprockets Series 882
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 882T (radius)
29
Description
Radius running plastic tab chain
Thick top plate = longer wear life
For side transfer with 821 and 831 series straight running chains
Chain data
Habasit code
C0882K0450DPTA
C0882K0450LFTA
C0882K0450PTTA
C0882K0750DPTA
C0882K0750LFTA
C0882K0750PTTA
C0882K1000DPTA
C0882K1000LFTA
C0882K1000PTTA
C0882K1200DPTA
C0882K1200LFTA
C0882K1200PTTA
C0882K1500DPTA
C0882K1500LFTA
C0882K1500PTTA
C0882K1600DPTA
C0882K1600LFTA
C0882K1600PTTA
Width W
mm
114.3
114.3
114.3
190.5
190.5
190.5
254.0
254.0
254.0
304.8
304.8
304.8
381.0
381.0
381.0
406.4
406.4
406.4
inch
4.50
4.50
4.50
7.50
7.50
7.50
10.00
10.00
10.00
12.00
12.00
12.00
15.00
15.00
15.00
16.00
16.00
16.00
Weight
kg/m
1.92
1.92
1.92
2.34
2.34
2.34
2.66
2.66
2.66
2.89
2.89
2.89
3.07
3.07
3.07
3.18
3.18
3.18
lb/ft
1.29
1.29
1.29
1.57
1.57
1.57
1.79
1.79
1.79
1.94
1.94
1.94
2.06
2.06
2.06
2.14
2.14
2.14
Nominal tensile
FN
N
2850
2850
2850
2850
2850
2850
2850
2850
2850
2850
2850
2850
2850
2850
2850
2850
2850
2850
strength
lbf
641
641
641
641
641
641
641
641
641
641
641
641
641
641
641
641
641
641
Rs
mm
610
610
610
610
610
610
610
610
610
610
610
610
686
686
686
686
686
686
Material
inch
24.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
27.0
27.0
27.0
27.0
27.0
27.0
DP
LF
PT
DP
LF
PT
DP
LF
PT
DP
LF
PT
DP
LF
PT
DP
LF
PT
Related products
Multi-Hub 882 sprocket rims
Multi-Hub inserts
Solid sprockets Series 882
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 882TG (radius)
30
Description
Radius running plastic tab chain
High friction GripTop inserts
Chain data
Habasit code
C0882K0450LFTG
C0882K0750LFTG
Width W
mm
114.3
190.5
inch
4.50
7.50
Weight
kg/m
2.00
2.40
lb/ft
1.34
1.61
Nominal tensile
FN
N
2850
2850
strength
lbf
641
641
Rs
mm
610
610
Material
inch
24.0
24.0
LF
LF
Related products
Multi-Hub 882 sprocket rims
Multi-Hub inserts
Solid sprockets Series 882
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 890T (radius)
31
Description
Chain data
Habasit code
C0890K0325LFTA
C0890K0450LFTA
Width W
mm
82.6
114.3
inch
3.25
4.50
Weight
kg/m
0.98
1.10
lb/ft
0.66
0.74
Nominal tensile
strength FN
N
lbf
1900
428
1900
428
J (straight)
mm
46.0
46.0
inch
1.81
1.81
J (curve)
mm
44.5
44.5
inch
1.75
1.75
Rs
mm
200
200
Material
inch
7.9
7.9
LF
LF
Related products
Multi-Hub 880 sprocket rims
Multi-Hub inserts
Solid sprockets Series 880
Options
Plastic pin
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 1061T (radius)
32
Description
Chain data
Habasit code
C1061K0330DPTA
C1061K0330LFTA
C1061K0330PTTA
C1061K0330TSTA
Width W
mm
83.8
83.8
83.8
83.8
inch
3.30
3.30
3.30
3.30
Weight
kg/m
1.55
1.55
1.55
1.55
lb/ft
1.04
1.04
1.04
1.04
Nominal tensile
FN
N
1650
1650
1650
1650
strength
lbf
371
371
371
371
Rs
mm
500
500
500
500
Material
inch
19.7
19.7
19.7
19.7
DP
LF
PT
TS
Related products
Multi-Hub 1060 sprocket rims
Multi-Hub inserts
Split sprockets Series 1061
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 1061M (radius)
33
Description
Chain data
Habasit code
C1061M0330DPAA
C1061M0330LFAA
C1061M0330PTAA
C1061M0330TSAA
Width W
mm
83.8
83.8
83.8
83.8
inch
3.30
3.30
3.30
3.30
Weight
kg/m
1.67
1.67
1.67
1.67
lb/ft
1.12
1.12
1.12
1.12
Nominal tensile
FN
N
1650
1650
1650
1650
strength
lbf
371
371
371
371
Rs
mm
500
500
500
500
Material
inch
19.7
19.7
19.7
19.7
DP
LF
PT
TS
Related products
Multi-Hub 1060 sprocket rims
Multi-Hub inserts
Split sprockets Series 1061
Magnetic corner tracks see HabiPLAST Product Guide Code No. 4097
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 1071B (radius)
34
Description
Chain data
Habasit code
C1071K330LFBA-003
C1071K0330HTBA
Width W
mm
83.8
83.8
inch
3.30
3.30
Weight
kg/m
1.55
1.51
lb/ft
1.04
1.01
Nominal tensile
strength FN
N
lbf
2230
500
2230
500
J (straight)
mm
44.5
44.5
inch
1.75
1.75
J (curve)
mm
41.3
41.3
inch
1.62
1.62
Rs
mm
457
457
Material
inch
18.0
18.0
LF
HT
Related products
Multi-Hub 1060 Sprocket-Rims
Multi-Hub Inserts
Split Sprockets - Series 1061
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top plastic accessories
35
Inserts
Inserts can be fitted into most Slat Top plastic chain types to increase the friction between product and chain.
This is beneficial for incline or decline applications.
1. Serial inserts (e.g. 882TG)
Standard insert material is G
65 Shore A hardness
Heavy duty insert
2. Custom inserts
Standard insert material PL (other materials like HY available)
85 Shore A hardness (other hardness grades available in other materials)
Available as individual links or assembled into chain lengths (standard packaging: 3.048 m = 10 ft)
For order code of special building pattern see page Nomenclature
Custom insert dimensions are shown in the table below
Chain type
Chain width
Insert type
325
400 (only 820)
820 / 831
Insert width L
mm
inch
60
2.36
90
3.54
105
4.13
130
5.12
130
5.12
200
7.87
XB
295
11.61
60
2.36
XA
90
3.54
750
130
5.12
450
90
3.54
450
XA
1000
1200
325
879 / 880
882B / 882T
450
750
1200
882T
Type XA
XA
130
5.12
200
7.87
XB
295
11.61
XB
295
11.61
1000
1500
1600
Type XB
This is only a brief overview of our inserts. Many different insert designs are available.
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top plastic accessories
36
Drilled holes
For special applications (e.g. vacuum) when holes in
Slat Top chains are needed, we offer HabaCHAIN Slat
Top plastic chains with custom-made drilled holes.
The holes are drilled on a dedicated CNC machine
according to the pattern specified by the customer.
All types of hole shapes (not only round) can be
machined. For further information and availability
please contact your local Habasit partner.
4185BRO.CHA-en1115HQR
HabaCHAIN
LBP 821 (straight)
37
Description
Straight running low-back pressure chain
Patented design
Chain data
Habasit code
C0821K0750LFAR
C0821K1000LFAR
C0821K1200LFAR
Width W
mm
190.5
254.0
304.8
Weight
inch
7.50
10.00
12.00
kg/m
4.20
5.50
6.50
lb/ft
2.82
3.70
4.37
Material
LF
LF
LF
Related products
Multi-Hub 821 sprocket rims
Multi-Hub 881 sprocket rims (2 set-up side-by-side)
Multi-Hub inserts
Solid sprockets Series 821
4185BRO.CHA-en1115HQR
HabaCHAIN
LBP 821 SB (straight)
38
Description
Chain data
Habasit code
C0821K0750LFAS
C0821K1000LFAS
C0821K1200LFAS
Width W
mm
190.5
254.0
304.8
Weight
inch
7.50
10.00
12.00
kg/m
3.60
4.70
5.50
lb/ft
2.42
3.16
3.70
Material
LF
LF
LF
Related products
Multi-Hub 821 sprocket rims
Multi-Hub 881 sprocket rims (2 set-up side-by-side))
Multi-Hub inserts
Solid sprockets Series 821
4185BRO.CHA-en1115HQR
HabaCHAIN
LBP 882T (radius)
39
Description
Radius running low-back pressure chain
Patented design
Chain data
Habasit code
C0882K0750LFTR
C0882K1000LFTR
C0882K1200LFTR
Width W
mm
190.5
254.0
304.8
inch
7.50
10.00
12.00
Weight
kg/m
4.40
5.30
6.00
lb/ft
2.96
3.56
4.03
Nominal tensile
FN
N
2850
2850
2850
strength
lbf
641
641
641
Rs
mm
610
610
610
Material
inch
24.0
24.0
24.0
LF
LF
LF
Related products
Multi-Hub 882 sprocket rims
Multi-Hub inserts
Solid sprockets Series 882
4185BRO.CHA-en1115HQR
HabaCHAIN
LBP 882T SB (radius)
40
Description
Chain data
Habasit code
C0882K0750LFTS
C0882K1000LFTS
C0882K1200LFTS
Width W
mm
190.5
254.0
304.8
inch
7.50
10.00
12.00
Weight
kg/m
3.90
4.70
5.40
lb/ft
2.62
3.16
3.63
Nominal tensile
FN
N
2850
2850
2850
strength
lbf
641
641
641
Rs
mm
610
610
610
Material
inch
24.0
24.0
24.0
LF
LF
LF
Related products
Multi-Hub 882 sprocket rims
Multi-Hub inserts
Solid sprockets Series 882
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 800 (straight)
41
Description
Straight running steel chain
Double hinge design = identical sprocket for 800 and 821 series chain
For side transfer with 881 series radius running chain
Chain data
Habasit code
C0800J0750CSAA
C0800K0750SSAA
C0800K0750SHAA
C0800P0750SAAA
Width W
mm
190.5
190.5
190.5
190.5
inch
7.50
7.50
7.50
7.50
Weight
kg/m
5.80
5.80
5.80
5.80
lb/ft
3.90
3.90
3.90
3.90
Nominal tensile
strength FN
N
lbf
11500
2588
7000
1575
9000
2025
8000
1800
Rb
mm
150
150
150
150
Plate clearance A
inch
5.90
5.90
5.90
5.90
mm
1.6
1.6
1.6
1.6
inch
0.06
0.06
0.06
0.06
Ra
Material
<0.3
<0.5
CS
SS
SH
SA
Pin material: case hardened carbon steel (for CS chain), stainless steel (for SS, SH and SA chain)
Standard packaging: 3.048 m = 10ft
The weight specification is indicative
Bakery bends available
Related products
Multi-Hub 821sprocket rims
Multi-Hub 881 sprocket rims (2 set-up side-by-side)
Multi-Hub inserts
Solid sprockets Series 821
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 810 (straight)
42
Description
Straight running steel chain
For side transfer with 881 series radius running chain
Chain data
Habasit code
C0810J0225CSAA
C0810K0225SSAA
C0810K0225SHAA
C0810P0225SAAA
C0810J0325CSAA
C0810K0325SSAA
C0810K0325SHAA
C0810P0325SAAA
C0810K0330SSAA
C0810K0330SHAA
C0810J0400CSAA
C0810K0400SSAA
C0810K0400SHAA
C0810P0400SAAA
C0810J0450CSAA
C0810K0450SSAA
C0810K0450SHAA
C0810P0450SAAA
C0810J0600CSAA
C0810K0600SSAA
C0810K0600SHAA
C0810P0600SAAA
C0810J0750CSAA
C0810K0750SSAA
C0810K0750SHAA
C0810P0750SAAA
Width W
mm
57.1
57.1
57.1
57.1
82.6
82.6
82.6
82.6
83.8
83.8
101.6
101.6
101.6
101.6
114.3
114.3
114.3
114.3
152.4
152.4
152.4
152.4
190.5
190.5
190.5
190.5
inch
2.25
2.25
2.25
2.25
3.25
3.25
3.25
3.25
3.30
3.30
4.00
4.00
4.00
4.00
4.50
4.50
4.50
4.50
6.00
6.00
6.00
6.00
7.50
7.50
7.50
7.50
Weight
kg/m
2.18
2.18
2.18
2.18
2.65
2.65
2.65
2.65
2.67
2.67
3.00
3.00
3.00
3.00
3.30
3.30
3.30
3.30
4.20
4.20
4.20
4.20
5.10
5.10
5.10
5.10
lb/ft
1.46
1.46
1.46
1.46
1.78
1.78
1.78
1.78
1.79
1.79
2.02
2.02
2.02
2.02
2.22
2.22
2.22
2.22
2.82
2.82
2.82
2.82
3.43
3.43
3.43
3.43
Nominal tensile
strength FN
N
lbf
8500
1913
5000
1125
6000
1350
5500
1238
8500
1913
5000
1125
6000
1350
5500
1238
5000
1125
6000
1350
8500
1913
5000
1125
5000
1125
5500
1238
8500
1913
5000
1125
6000
1350
5500
1238
8500
1913
5000
1125
6000
1350
5500
1238
8500
1913
5000
1125
6000
1350
5500
1238
Rb
mm
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
Plate clearance A
inch
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
5.90
mm
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
inch
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
Ra
Material
m
<0.3
<0.3
<0.5
<0.3
<0.3
<0.5
<0.3
<0.3
<0.3
<0.5
<0.3
<0.3
<0.5
<0.3
<0.3
<0.5
<0.3
<0.3
<0.5
CS
SS
SH
SA
CS
SS
SH
SA
SS
SH
CS
SS
SH
SA
CS
SS
SH
SA
CS
SS
SH
SA
CS
SS
SH
SA
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 810 (straight)
43
Pin material: case hardened carbon steel (for CS chain), stainless steel (for SS, SH and SA chain)
Standard packaging: 3.048 m = 10ft
The weight specification is indicative
Bakery bends available
Related products
Multi-Hub 820 sprocket rims
Multi-Hub 820 idler rims
Multi-Hub inserts
Solid sprockets Series 810
Solid sprockets Series 820
Solid idler 810
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 881B (radius)
44
Description
Radius running steel bevel chain
For side transfer with 800 and 810 series straight running chain
Chain data
Habasit code
C0881J0325CSBA
C0881K0325SHBA
C0881P0325SABA
C0881J0450CSBA
C0881K0450SHBA
C0881P0450SABA
C0881J0750CSBA
C0881K0750SHBA
C0881P0750SABA
Width W
mm
82.6
82.6
82.6
114.3
114.3
114.3
190.5
190.5
190.5
inch
3.25
3.25
3.25
4.50
4.50
4.50
7.50
7.50
7.50
Weight
kg/m
2.90
2.90
2.90
3.60
3.60
3.60
5.30
5.30
5.30
lb/ft
1.95
1.95
1.95
2.42
2.42
2.42
3.56
3.56
3.56
Nominal tensile
strength FN
N
lbf
8000
1800
5500
1237
5000
1125
8000
1800
5500
1238
5000
1125
8000
1800
5500
1238
5000
1125
Rs
mm
457
457
457
500
500
500
500
500
500
Ra
inch
18.0
18.0
18.0
19.7
19.7
19.7
19.7
19.7
19.7
Material
m
<0.3
<0.5
<0.3
<0.5
<0.3
<0.5
CS
SH
SA
CS
SH
SA
CS
SH
SA
Pin material: case hardened carbon steel (for CS chain), stainless steel (for SH and SA chain)
Standard packaging: 3.048 m = 10ft
The weight specification is indicative
Bakery bends available
Related products
Multi-Hub 881 sprocket rims
Multi-Hub 820 idler rims
Multi-Hub inserts
Solid sprockets Series 881
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top 881T (radius)
45
Description
Radius running steel tab chain
For side transfer with 800 and 810 series straight running chain
Chain data
Habasit code
C0881J0325CSTA
C0881K0325SHTA
C0881P0325SATA
C0881J0450CSTA
C0881K0450SHTA
C0881P0450SATA
C0881J0750CSTA
C0881K0750SHTA
C0881P0750SATA
Width W
mm
82.6
82.6
82.6
114.3
114.3
114.3
190.5
190.5
190.5
inch
3.25
3.25
3.25
4.50
4.50
4.50
7.50
7.50
7.50
Weight
kg/m
3.10
3.10
3.10
3.80
3.80
3.80
5.50
5.50
5.50
lb/ft
2.08
2.08
2.08
2.55
2.55
2.55
3.70
3.70
3.70
Nominal tensile
strength FN
N
lbf
8000
1800
5500
1238
5000
1125
8000
1800
5500
1238
5000
1125
8000
1800
5500
1238
5000
1125
Rs
mm
457
457
457
500
500
500
500
500
500
Ra
inch
18.0
18.0
18.0
19.7
19.7
19.7
19.7
19.7
19.7
Material
m
<0.3
<0.5
<0.3
<0.5
<0.3
<0.5
CS
SH
SA
CS
SH
SA
CS
SH
SA
Pin material: case hardened carbon steel (for CS chain), stainless steel (for SH and SA chain)
Standard packaging: 3.048 m = 10ft
The weight specification is indicative
Bakery bends available
Related products
Multi-Hub 881 sprocket rims
Multi-Hub inserts
Solid sprockets Series 881
4185BRO.CHA-en1115HQR
HabaCHAIN
Slat Top steel accessories
46
Description
So called bakery bends are bended top plates of Slat Top steel chains. Bakery bends are used in the bakery
industry for products discharged from ovens. The bended edge ensures a smooth product transfer. Bakery
bends are available for 810 and 881T chain type in CS and SA material as indicated in the table below. The top
plate of the Slat Top steel chain is will be bended according to the dimensions in the drawing below.
Nomenclature:
One side bent in travel direction on the right side suffix: -R1
One side bent in travel direction on the left side suffix: -L1
Both sides bent suffix: -RL
Slat Top 810 (straight)
Chain type
C0810J0450CSAA
C0810J0600CSAA
C0810J0750CSAA
C0810P0450SAAA
C0810P0600SAAA
C0810P0750SAAA
B
mm
inch
-R1
18
114.3
4.5
19.1
0.75
6.4
0.25
-L1
18
114.3
4.5
19.1
0.75
6.4
0.25
-RL
18
114.3
4.5
19.1
0.75
6.4
0.25
-R1
14
152.4
25.4
6.4
0.25
-L1
14
152.4
25.4
6.4
0.25
-RL
14
152.4
25.4
6.4
0.25
-R1
14
190.5
7.5
25.4
6.4
0.25
-L1
14
190.5
7.5
25.4
6.4
0.25
-RL
14
190.5
7.5
25.4
6.4
0.25
-R1
18
114.3
4.5
19.1
0.75
6.4
0.25
-L1
18
114.3
4.5
19.1
0.75
6.4
0.25
-RL
18
114.3
4.5
19.1
0.75
6.4
0.25
-R1
14
152.4
25.4
6.4
0.25
-L1
14
152.4
25.4
6.4
0.25
0.25
-RL
14
152.4
25.4
6.4
-R1
14
190.5
7.5
25.4
6.4
0.25
-L1
14
190.5
7.5
25.4
6.4
0.25
-RL
14
190.5
7.5
25.4
6.4
0.25
C0881J0450CSTA
C0881J0750CSTA
C0881P0450SATA
C0881P0750SATA
B
mm
inch
-R1
18
114.3
4.5
19.1
0.75
6.4
0.25
-L1
18
114.3
4.5
19.1
0.75
6.4
0.25
-RL
18
114.3
4.5
19.1
0.75
6.4
0.25
-R1
14
190.5
7.5
25.4
6.4
0.25
-L1
14
190.5
7.5
25.4
6.4
0.25
-RL
14
190.5
7.5
25.4
6.4
0.25
-R1
18
114.3
4.5
19.1
0.75
6.4
0.25
-L1
18
114.3
4.5
19.1
0.75
6.4
0.25
-RL
18
114.3
4.5
19.1
0.75
6.4
0.25
-R1
14
190.5
7.5
25.4
6.4
0.25
-L1
14
190.5
7.5
25.4
6.4
0.25
-RL
14
190.5
7.5
25.4
6.4
0.25
4185BRO.CHA-en1115HQR
HabaCHAIN
Flexi 7100HA
47
Description
Chain data
Habasit code
C7100P0248LFHA
C7100P0248PTHA
C7100K0325LFHA
C7100K0325PTHA
C7100K0405LFHA
C7100K0405PTHA
Width W
mm
63.0
63.0
83.0
83.0
103.0
103.0
Habasit code
C7100P0248LFHA
C7100P0248PTHA
C7100K0325LFHA
C7100K0325PTHA
C7100K0405LFHA
C7100K0405PTHA
Weight
Nominal
tensile
strength FN
N
lbf
500 113
500 113
1250 281
1250 281
1250 281
1250 281
Rs
mm
150.0
150.0
160.0
160.0
170.0
170.0
mm
21.1
21.1
35.6
35.6
46.0
46.0
inch
0.83
0.83
1.40
1.40
1.81
1.81
mm
3.6
3.6
3.8
3.8
4.8
4.8
inch
0.14
0.14
0.15
0.15
0.19
0.19
mm
7.1
7.1
7.1
7.1
7.1
7.1
P
inch
5.91
5.91
6.30
6.30
6.69
6.69
mm
25.4
25.4
33.5
33.5
35.5
35.5
inch
0.28
0.28
0.28
0.28
0.28
0.28
mm
7.9
7.9
11.1
11.1
12.1
12.1
T
inch
1.00
1.00
1.32
1.32
1.40
1.40
mm
37.1
37.1
58.1
58.1
77.5
77.5
Rb
inch
0.31
0.31
0.44
0.44
0.48
0.48
mm
70
70
90
90
100
100
inch
2.76
2.76
3.54
3.54
3.94
3.94
Material
inch
1.46
1.46
2.29
2.29
3.05
3.05
LF
PT
LF
PT
LF
PT
Related products
Solid sprockets Series 7100
Solid idlers Series 7100
HabiPLAST wear strip FL W 15.5x6.1
4185BRO.CHA-en1115HQR
HabaCHAIN
Snap-on 843 (straight)
48
Description
Straight running snap-on chain
Steel base roller chain with snap-on plastic top plates
Base chain: 0.5" pitch 843 roller chain
Chain data
Habasit code
C0843S0138DPAA
C0843S0138LFAA
C0843S0138PTAA
C0843S0144DPAA
C0843S0144LFAA
C0843S0144PTAA
C0843S0200DPAA
C0843S0200LFAA
C0843S0200PTAA
C0843S0325DPAA
C0843S0325LFAA
C0843S0325PTAA
Width W
mm
35.0
35.0
35.0
36.6
36.6
36.6
50.8
50.8
50.8
82.6
82.6
82.6
Weight
inch
1.38
1.38
1.38
1.44
1.44
1.44
2.00
2.00
2.00
3.25
3.25
3.25
kg/m
0.83
0.83
0.83
0.83
0.83
0.83
0.89
0.89
0.89
10.30
10.30
10.30
lb/ft
0.56
0.56
0.56
0.56
0.56
0.56
0.60
0.60
0.60
6.92
6.92
6.92
Material
DP
LF
PT
DP
LF
PT
DP
LF
PT
DP
LF
PT
Base chain:
Standard material is CS
Stainless steel (SS) on request: Max. workload 1800 N (400 lbf)
Nomenclature for base chain only:
- C0843B0050CS
- C0843B0050SS
4185BRO.CHA-en1115HQR
HabaCHAIN
Snap-on 843C (straight)
49
Description
Chain data
Habasit code
C843CS0138DPAA
C843CS0138LFAA
C843CS0138PTAA
C843CS0200DPAA
C843CS0200LFAA
C843CS0200PTAA
C843CS0325DPAA
C843CS0325LFAA
C843CS0325PTAA
Width W
mm
35.0
35.0
35.0
50.8
50.8
50.8
82.6
82.6
82.6
Weight
inch
1.38
1.38
1.38
2.00
2.00
2.00
3.25
3.25
3.25
kg/m
0.86
0.86
0.86
0.92
0.92
0.92
1.06
1.06
1.06
lb/ft
0.58
0.58
0.58
0.62
0.62
0.62
0.71
0.71
0.71
Material
DP
LF
PT
DP
LF
PT
DP
LF
PT
Base chain:
Standard material is CS
Stainless steel (SS) on request: Max. workload 1800 N (400 lbf)
Nomenclature for base chain only:
- C0843B0050CS
- C0843B0050SS
4185BRO.CHA-en1115HQR
HabaCHAIN
Snap-on 863 (straight)
50
Description
Straight running snap-on chain
Steel base roller chain with snap-on plastic top plates
Base chain: 0.75" pitch 863 roller chain
Chain data
Habasit code
C0863S0325DPAA
C0863S0325LFAA
C0863S0450DPAA
C0863S0450LFAA
C0863S0600DPAA
C0863S0600LFAA
C0863S0750DPAA
C0863S0750LFAA
Width W
mm
82.6
82.6
114.3
114.3
152.4
152.4
190.5
190.5
Weight
inch
3.25
3.25
4.50
4.50
6.00
6.00
7.50
7.50
kg/m
2.10
2.10
2.30
2.30
2.53
2.53
2.68
2.68
lb/ft
1.41
1.41
1.55
1.55
1.70
1.70
1.80
1.80
Material
DP
LF
DP
LF
DP
LF
DP
LF
Base chain:
Standard material is CS
Stainless steel (SS) on request: Max. workload 3000 N (675 lbf)
Nomenclature for base chain only:
- C0863B0075CS
- C0863B0075SS
4185BRO.CHA-en1115HQR
HabaCHAIN
Snap-on 863T (straight)
51
Description
Straight running snap-on chain with tab
Steel base roller chain with snap-on plastic top plates
Base chain: 0.75" pitch 863 roller chain
Chain data
Habasit code
C0863S0250DPTA
C0863S0250LFTA
C0863S0325DPTA
C0863S0325LFTA
C0863S0450DPTA
C0863S0450LFTA
C0863S0500DPTA
C0863S0500LFTA
C0863S0750DPTA
C0863S0750LFTA
C0863S1000DPTA
C0863S1000LFTA
Width W
mm
63.5
63.5
82.6
82.6
114.3
114.3
127.0
127.0
190.5
190.5
254.0
254.0
Weight
inch
2.50
2.50
3.25
3.25
4.50
4.50
5.00
5.00
7.50
7.50
10.00
10.00
kg/m
2.10
2.10
2.19
2.19
2.37
2.37
2.41
2.41
2.71
2.71
3.17
3.17
lb/ft
1.41
1.41
1.47
1.47
1.59
1.59
1.62
1.62
1.82
1.82
2.13
2.13
Material
DP
LF
DP
LF
DP
LF
DP
LF
DP
LF
DP
LF
Base chain:
Standard material is CS
Stainless steel (SS) on request: Max. workload 3000 N (675 lbf)
Nomenclature for base chain only:
- C0863B0075CS
- C0863B0075SS
4185BRO.CHA-en1115HQR
HabaCHAIN
Snap-on 963 (straight)
52
Description
Straight running snap-on chain
Steel base roller chain with snap-on plastic top plates
Base chain: 0.75" pitch 1873 roller chain
Chain data
Habasit code
C0963S0325DPAA
C0963S0325LFAA
C0963S0450DPAA
C0963S0450LFAA
C0963S0600DPAA
C0963S0600LFAA
C0963S0750DPAA
C0963S0750LFAA
Width W
mm
82.6
82.6
114.3
114.3
152.4
152.4
190.5
190.5
Weight
inch
3.25
3.25
4.50
4.50
6.00
6.00
7.50
7.50
kg/m
2.10
2.10
2.30
2.30
2.53
2.53
2.68
2.68
lb/ft
1.41
1.41
1.55
1.55
1.70
1.70
1.80
1.80
Material
DP
LF
DP
LF
DP
LF
DP
LF
Base chain:
Standard material is CS
Stainless steel (SS) on request: Max. workload 2000 N (450 lbf)
Nomenclature for base chain only:
- C1873B0075CS
- C1873B0075SS
4185BRO.CHA-en1115HQR
HabaCHAIN
Snap-on 963T (straight)
53
Description
Straight running snap-on chain with tab
Steel base roller chain with snap-on plastic top plates
Base chain: 0.75" pitch 1873 roller chain
Chain data
Habasit code
C0963S0250DPTA
C0963S0250LFTA
C0963S0325DPTA
C0963S0325LFTA
C0963S0450DPTA
C0963S0450LFTA
C0963S0500DPTA
C0963S0500LFTA
C0963S0750DPTA
C0963S0750LFTA
C0963S1000DPTA
C0963S1000LFTA
Width W
mm
63.5
63.5
82.6
82.6
114.3
114.3
127.0
127.0
190.5
190.5
254.0
254.0
Weight
inch
2.50
2.50
3.25
3.25
4.50
4.50
5.00
5.00
7.50
7.50
10.00
10.00
kg/m
2.10
2.10
2.19
2.19
2.37
2.37
2.41
2.41
2.71
2.71
3.17
3.17
lb/ft
1.41
1.41
1.47
1.47
1.59
1.59
1.62
1.62
1.82
1.82
2.13
2.13
Material
DP
LF
DP
LF
DP
LF
DP
LF
DP
LF
DP
LF
Base chain:
Standard material is CS
Stainless steel (SS) on request: Max. workload 2000 N (450 lbf)
Nomenclature for base chain only:
- C1873B0075CS
- C1873B0075SS
4185BRO.CHA-en1115HQR
HabaCHAIN
Snap-on 1843T (radius)
54
Description
Radius running snap-on chain with tab
Steel base roller chain with snap-on plastic top plates
Base chain: 0.5" pitch 1843 roller chain
Chain data
Habasit code
C1843S0125DPTA
C1843S0125LFTA
C1843S0125PTTA
C1843S0150DPTA
C1843S0150LFTA
C1843S0150PTTA
C1843S0200DPTA
C1843S0200LFTA
C1843S0200PTTA
C1843S0325DPTA
C1843S0325LFTA
C1843S0325PTTA
Width W
mm
31.7
31.7
31.7
38.1
38.1
38.1
50.8
50.8
50.8
82.6
82.6
82.6
inch
1.25
1.25
1.25
1.50
1.50
1.50
2.00
2.00
2.00
3.25
3.25
3.25
Weight
kg/m
0.83
0.83
0.83
0.85
0.85
0.85
0.90
0.90
0.90
1.02
1.02
1.02
lb/ft
0.56
0.56
0.56
0.57
0.57
0.57
0.60
0.60
0.60
0.69
0.69
0.69
Nominal tensile
strength FN
N
lbf
2500
563
2500
563
2500
563
2500
563
2500
563
2500
563
2500
563
2500
563
2500
563
2500
563
2500
563
2500
563
J (straight)
mm
22.4
22.4
22.4
22.4
22.4
22.4
22.4
22.4
22.4
22.4
22.4
22.4
inch
0.88
0.88
0.88
0.88
0.88
0.88
0.88
0.88
0.88
0.88
0.88
0.88
J (curve)
mm
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
inch
0.84
0.84
0.84
0.84
0.84
0.84
0.84
0.84
0.84
0.84
0.84
0.84
Rs
mm
315
315
315
315
315
315
315
315
315
315
315
315
Material
inch
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
12.4
DP
LF
PT
DP
LF
PT
DP
LF
PT
DP
LF
PT
Base chain:
Standard material is CS
Stainless steel (SS) on request: Max. workload 1800 N (400 lbf)
Nomenclature for base chain only:
- C1843B0050CS
- C1843B0050SS
4185BRO.CHA-en1115HQR
HabaCHAIN
Snap-on 1873T (radius)
55
Description
Chain data
Habasit code
C1873S0225DPTA
C1873S0225LFTA
C1873S0250DPTA
C1873S0250LFTA
C1873S0325DPTA
C1873S0325LFTA
C1873S0450DPTA
C1873S0450LFTA
C1873S0600DPTA
C1873S0600LFTA
C1873S0750DPTA
C1873S0750LFTA
C1873S1000DPTA
C1873S1000LFTA
C1873S1200DPTA
C1873S1200LFTA
Width W
mm
57.2
57.2
63.5
63.5
82.6
82.6
114.3
114.3
152.4
152.4
190.5
190.5
254.0
254.0
304.8
304.8
inch
2.25
2.25
2.50
2.50
3.25
3.25
4.50
4.50
6.00
6.00
7.50
7.50
10.00
10.00
12.00
12.00
Weight
kg/m
1.97
1.97
2.00
2.00
2.10
2.10
2.26
2.26
2.41
2.41
2.56
2.56
2.78
2.78
3.01
3.01
lb/ft
1.32
1.32
1.34
1.34
1.41
1.41
1.52
1.52
1.62
1.62
1.72
1.72
1.87
1.87
2.02
2.02
Nominal tensile
strength FN
N
lbf
4000
900
4000
900
4000
900
4000
900
4000
900
4000
900
4000
900
4000
900
4000
900
4000
900
4000
900
4000
900
4000
900
4000
900
4000
900
4000
900
J (straight)
mm
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
inch
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
J (curve)
mm
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
inch
1.38
1.38
1.38
1.38
1.38
1.38
1.38
1.38
1.38
1.38
1.38
1.38
1.38
1.38
1.38
1.38
Rs
mm
356
356
356
356
356
356
356
356
457
457
457
457
457
457
457
457
Material
inch
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
DP
LF
DP
LF
DP
LF
DP
LF
DP
LF
DP
LF
DP
LF
DP
LF
Base chain:
Standard material is CS
Stainless steel (SS) on request: Max. workload 2000 N (450 lbf)
Nomenclature for base chain only:
- C1873B0075CS
- C1873B0075SS
4185BRO.CHA-en1115HQR
HabaCHAIN
Snap-on 1873T-T (straight)
56
Description
Chain data
Habasit code
C1873S0325DPTA-T
C1873S0325LFTA-T
C1873S0450DPTA-T
C1873S0450LFTA-T
C1873S0600DPTA-T
C1873S0600LFTA-T
C1873S0750DPTA-T
C1873S0750LFTA-T
Width W
mm
82.6
82.6
114.3
114.3
152.4
152.4
190.5
190.5
Weight
inch
3.25
3.25
4.50
4.50
6.00
6.00
7.50
7.50
kg/m
2.14
2.14
2.32
2.32
2.53
2.53
2.74
2.74
lb/ft
1.44
1.44
1.56
1.56
1.70
1.70
1.84
1.84
Material
DP
LF
DP
LF
DP
LF
DP
LF
Base chain:
Standard material is CS
Stainless steel (SS) on request: Max. workload 2000 N (450 lbf)
Nomenclature for base chain only:
- C1873B0075CS
- C1873B0075SS
4185BRO.CHA-en1115HQR
HabaCHAIN
Snap-on 1873-D1 (radius)
57
Description
Chain data
Habasit code
C1873S0375LFTG-D1
Width W
mm
95.3
inch
3.75
Weight
kg/m
2.90
lb/ft
1.95
Nominal tensile
strength FN
N
lbf
4000
900
J (straight)
mm
33.3
inch
1.31
J (curve)
mm
35.1
inch
1.38
Rs
mm
356
Material
inch
14.0
LF
Base chain:
Standard material is CS
Stainless steel (SS) on request: Max. workload 2000 N (450 lbf)
Nomenclature for base chain only:
- C1873B0075CS
- C1873B0075SS
4185BRO.CHA-en1115HQR
HabaCHAIN
Snap-on 1873-L4 (radius)
58
Description
Chain data
Habasit code
C1873S0375LFTG-L4
Width W
mm
95.3
inch
3.75
Weight
kg/m
2.80
lb/ft
1.88
Nominal tensile
strength FN
N
lbf
4000
900
J (straight)
mm
33.3
inch
1.31
J (curve)
mm
35.1
inch
1.38
Rs
mm
356
Material
inch
14.0
LF
Base chain:
Standard material is CS
Stainless steel (SS) on request: Max. workload 2000 N (450 lbf)
Nomenclature for base chain only:
- C1873B0075CS
- C1873B0075SS
4185BRO.CHA-en1115HQR
HabaCHAIN
Snap-on 1874T (radius)
59
Description
Chain data
Habasit code
C1874S0325CSTA
C1874S0450CSTA
C1874S0600CSTA
C1874S0750CSTA
Width W
mm
82.6
114.3
152.4
190.5
inch
3.25
4.50
6.00
7.50
Weight
kg/m
4.20
4.80
5.70
6.40
lb/ft
2.82
3.25
3.83
4.30
Nominal tensile
strength FN
N
lbf
4000
900
4000
900
4000
900
4000
900
J (straight)
mm
34.1
34.1
34.1
34.1
inch
1.34
1.34
1.34
1.34
J (curve)
mm
34.6
34.6
34.6
34.6
inch
1.36
1.36
1.36
1.36
Rs
mm
356
356
457
610
Material
inch
14.0
14.0
16.0
24.0
CS
CS
CS
CS
Base chain:
Standard material is CS
Nomenclature for base chain only:
- C1873B0075CS
4185BRO.CHA-en1115HQR
HabaCHAIN
Snap-on 3873T (radius)
60
Description
Chain data
Habasit code
C3873S1000DPTA
C3873S1000LFTA
Width W
mm
254.0
254.0
inch
10.00
10.00
Weight
kg/m
3.47
3.47
lb/ft
2.33
2.33
Nominal tensile
strength FN
N
lbf
4000
900
4000
900
J (straight)
mm
33.3
33.3
inch
1.31
1.31
J (curve)
mm
35.1
35.1
inch
1.38
1.38
Rs
mm
457
457
Material
inch
18.0
18.0
DP
LF
Base chain:
Standard material is CS
Stainless steel (SS) on request: Max. workload 2'000 N (450 lbf)
Nomenclature for base chain only:
- C1873B0075CS
- C1873B0075SS
4185BRO.CHA-en1115HQR
HabaCHAIN
Snap-on accessories
61
Inserts
Custom inserts can be fitted into most Snap-on Chain types to increase the friction between product and chain.
This is beneficial for incline or decline applications.
Standard insert material is PL (other materials like HY on request)
Chain links with inserts can be ordered either individually or ready-built into chain lengths (standard packaging: 3.048 m = 10 ft)
For order code of special building pattern see page Nomenclature
Standard insert dimensions are shown in the table below
Chain type
Chain width
Insert type
inch
60
2.36
105
4.13
130
5.12
325
60
2.36
450
90
3.54
130
5.12
325
863 / 963
450
600
XA
750
1873T
600
XA
750
1000
1200
Type XA
Insert width L
mm
XB
200
7.87
295
11.61
Type XB
This is only a brief overview of our inserts. Many different insert designs are available.
For further information and availability please contact your local Habasit partner.
Loose Snap-on plastic top plates are available on request (suffix TP). Minimum delivery is 25 pieces.
Connecting links are available on request
For order code see page "Nomenclature"
4185BRO.CHA-en1115HQR
HabaCHAIN
Multiflex 1700 (radius)
62
Description
Multiflex plastic chain with wide top plate
Capable to run on corner discs
For conveyor layouts requiring tight turns
Chain data
Habasit code
C1700K0217LFAA
Width W
mm
55.0
Weight
inch
2.17
kg/m
1.28
lb/ft
0.86
Material
LF
Related products
Solid sprockets Series 1700
Turning discs
4185BRO.CHA-en1115HQR
HabaCHAIN
Multiflex 1701T (radius)
63
Description
Multiflex plastic chain with tab
Capable to run on corner discs
For conveyor layouts requiring tight turns
Chain data
Habasit code
C1701K0209LFTA
Width W
mm
53.2
inch
2.09
Weight
kg/m
1.34
lb/ft
0.9
Nominal tensile
strength FN
N
lbf
2600
584
J (straight)
mm
59.5
inch
2.34
J (curve)
mm
57.2
inch
2.25
Material
LF
Related products
Solid sprocket Series 1700
Turning discs
4185BRO.CHA-en1115HQR
HabaCHAIN
Multiflex 1702 (radius)
64
Description
Multiflex plastic chain without tab
Capable to run on corner discs
For conveyor layouts requiring tight turns
Chain data
Habasit code
C1702K0209LFAA
Width W
mm
53.2
inch
2.09
Weight
kg/m
1.29
lb/ft
0.87
Nominal tensile
strength FN
N
lbf
2600
584
J (straight)
mm
62.0
inch
2.44
J (curve)
mm
59.6
inch
2.35
Material
LF
Related products
Solid sprocket Series 1700
Turning discs
4185BRO.CHA-en1115HQR
HabaCHAIN
Multiflex chain accessories
65
Extended pivots and inserts can be fitted to the multiflex range of chains. Inserts are benifical for incline or
decline applications where the extended pivots can be used for a variety of applications where the product is
required to be spaced, held or pushed where the stand alone chain is not sufficient. Both inserts and extended
pivots are available in standard arrangements as well as to customer requirements.
Extended pivot
Insert
Standard accessories
Chain type
Accessory type
C1700
C1701T
C1702
C1700
C1701T
C1702
Dimension H
mm
inch
26.5
1.04
25.5
1.00
Extended pivot
Insert
Standard
material
PA white
see material
overview
4185BRO.CHA-en1115HQR
HabaCHAIN
Multiflex chain accessories
66
Turn disc are available for the Multiflex range of chains. Turn discs are used as moving inside wearstrips for
turns. By using the turn disc, the chain can go through a curve without significantly increasing the chain
tension, consequently, allowing longer conveyors. It is recommended to utilize turn disc for multiflex chains.
19.8
(0.78")
150
(5.91")
Chain type
C1700D12
C1700K0217--AA
(1.25")
Mounting plate
(non included)
3/416 UNC2A
Threaded shaft
31.8
37.3
(1.47")
61.2
(2.41")
123
(4.84")
Weight
mm
inch
kg
lbs
150
5.91
1.39
3.05
15.7
(0.62")
150
(5.91")
C1701D12
Chain type
(1.25")
Mounting plate
(non included)
3/416 UNC2A
Threaded shaft
31.8
37.3
(1.47")
61.2
(2.41")
123.4
(4.86")
Weight
mm
inch
kg
lbs
C1701K0209--TA
150
5.91
1.32
2.90
C1702K0209--AA
150
5.91
1.32
2.90
Material:
Disc: Cast aluminum
Shaft: Stainless steel
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 40P (straight)
67
Description
Small straight running plastic chain with closed top plate
Driven by standard 0.5" (12.7 mm) pitch steel roller chain sprocket
For applications requiring a closed top plate design that eliminates pinch points
Chain data
Habasit code
C0040P0079DPAA-001
Width W
mm
20.0
Weight
inch
0.79
kg/m
0.37
lb/ft
0.25
Material
DP
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 60P (straight)
68
Description
Small straight running plastic chain with closed top plate
Driven by standard 0.75" (19.1 mm) pitch steel roller chain sprocket
For applications requiring a closed top plate design that eliminates pinch points
Chain data
Habasit code
C0060P0118DPAA-001
Width W
mm
30.0
Weight
inch
1.18
kg/m
0.71
lb/ft
0.48
Material
DP
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 600 (radius)
69
Description
Radius running plastic chain
Closed top design
Chain data
Habasit code
C0600P0165DPAA-001
Width W
mm
42.0
Weight
inch
1.65
kg/m
1.44
lb/ft
0.97
Material
DP
Related products
Solid sprockets Series 600
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 601 (radius)
70
Description
Radius running plastic chain
Open top design
Chain data
Habasit code
C0601P0165DPAA-001
Width W
mm
42.0
Weight
inch
1.65
kg/m
1.35
lb/ft
0.91
Material
DP
Related products
Solid sprockets Series 600
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 610T (radius)
71
Description
Radius running plastic tab chain
Closed top design
Chain data
Habasit code
C0610P0165DPTA-001
Width W
mm
42.0
Weight
inch
1.65
kg/m
1.54
lb/ft
1.03
Material
DP
Related products
Solid sprockets Series 600
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 611T (radius)
72
Description
Radius running plastic tab chain
Open top design
The tab shape is different compared to 611TE
Chain data
Habasit code
C0611P0165DPTA-001
Width W
mm
42.0
Weight
inch
1.65
kg/m
1.43
lb/ft
0.96
Material
DP
Related products
Solid sprockets Series 600
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 611TE (radius)
73
Description
Radius running plastic tab chain
Open top design
The tab shape is different compared to 611T
Chain data
Habasit code
C0611P0169DPTE-001
Width W
mm
43.0
Weight
inch
1.69
kg/m
1.10
lb/ft
0.74
Material
DP
Related products
Solid sprockets Series 600
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 1100 (straight)
74
Description
Straight running plastic chain
Designed for bi-directional travel
Chain data
Habasit code
C1100P0100DPAA
C1100P0100NYAA
C1100P0100HTAA
Width W
mm
25.4
25.4
25.4
Weight
inch
1.00
1.00
1.00
kg/m
0.30
0.29
0.29
lb/ft
0.20
0.20
0.20
Material
DP
NY
HT
Related products
Solid sprockets Series 1100
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 1110T (radius)
75
Description
Radius running plastic tab chain
Designed for bi-directional travel
Chain data
Habasit code
C1110P0100DPTA
C1110P0100NYTA
C1110P0100HTTA
Width W
mm
25.4
25.4
25.4
Weight
inch
1.00
1.00
1.00
kg/m
0.31
0.30
0.30
lb/ft
0.21
0.20
0.20
Material
DP
NY
HT
Related products
Solid sprockets Series 1100
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 1150 (straight)
76
Description
Straight running plastic chain
Designed for bi-directional travel
Chain data
Habasit code
C1150P0165HTAA
Width W
mm
41.9
Weight
inch
1.65
kg/m
0.65
lb/ft
0.44
Material
HT
Related products
Solid sprockets Series 1150
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 1151T (radius)
77
Description
Radius running plastic tab chain
Designed for bi-directional travel
Chain data
Habasit code
C1151P0165HTTA
Width W
mm
41.9
Weight
inch
1.65
kg/m
0.66
lb/ft
0.44
Material
HT
Related products
Solid sprockets Series 1150
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 1200 (straight)
78
Description
Straight running plastic chain
The 1200 series is identical to the 3200 series except for the material variety and the available accessories
Designed for bi-directional travel
Chain data
Habasit code
C1200P0224DPAA
C1200P0224HTAA
Width W
mm
57.0
57.0
Weight
inch
2.24
2.24
kg/m
1.30
1.30
lb/ft
0.87
0.87
Material
DP
HT
Related products
Solid sprockets Series 1200
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 1201AB (straight)
79
Description
Chain data
Habasit code
C1201P0224DPAB-00N
Width W
mm
57.0
Weight
inch
2.24
kg/m
1.51
lb/ft
1.01
Material
DP
Related products
Solid sprockets Series 1200
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 1210T (radius)
80
Description
Radius running plastic tab chain
The 1210T series is identical to the 3210T series except for the material variety, the sideflexing radius and the
available accessories
Designed for bi-directional travel
Chain data
Habasit code
C1210P0224DPTA
C1210P0224HTTA
Width W
mm
57.0
57.0
inch
2.24
2.24
Weight
kg/m
1.35
1.35
lb/ft
0.91
0.91
Nominal tensile
FN
N
2500
2500
strength
lbf
563
563
Rs
mm
457
457
Material
inch
18.0
18.0
DP
HT
Related products
Solid sprockets Series 1200
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 1211TB (radius)
81
Description
Chain data
Habasit code
C1211P0224DPTB-00N
Width W
mm
57.0
Weight
inch
2.24
kg/m
1.51
lb/ft
1.01
Material
DP
Related products
Solid sprockets Series 1200
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 1250 (straight)
82
Description
Straight running plastic chain
Designed for bi-directional travel
Chain data
Habasit code
C1250P0225HTAA
Width W
mm
57.2
Weight
inch
2.25
kg/m
1.73
lb/ft
1.16
Material
HT
Related products
Solid sprockets Series 1250
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 1251T (radius)
83
Description
Radius running plastic tab chain
Designed for bi-directional travel
Chain data
Habasit code
C1251P0225HTTA
Width W
mm
57.2
Weight
inch
2.25
kg/m
1.73
lb/ft
1.16
Material
HT
Related products
Solid sprockets Series 1250
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 1400 (radius)
84
Description
Radius running plastic chain
Open top design
Chain data
Habasit code
C1400P0200DPAA-001
Width W
mm
50.8
Weight
inch
2.00
kg/m
2.08
lb/ft
1.40
Material
DP
Related products
Solid sprockets Series 1400
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 1410T (radius)
85
Description
Radius running plastic tab chain
Open top design
Chain data
Habasit code
C1410P0200DPTA-001
Width W
mm
50.8
Weight
inch
2.00
kg/m
2.27
lb/ft
1.53
Material
DP
Related products
Solid sprockets Series 1400
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 3200 (straight)
86
Description
Straight running plastic chain
The 3200 series is identical to the 1200 series except for the material variety and the available accessories
Designed for bi-directional travel
Chain data
Habasit code
C3200K0224DPAA-001
C3200K0224DPAA-002
C3200K0224DPAA-008
C3200K0224NYAA-008
Width W
mm
57.0
57.0
57.0
57.0
Weight
inch
2.24
2.24
2.24
2.24
kg/m
1.30
1.30
1.30
1.06
lb/ft
0.87
0.87
0.87
0.71
Material
DP
DP
DP
NY
Related products
Solid sprockets Series 3200
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain 3210T (radius)
87
Description
Radius running plastic tab chain
The 3210T series is identical to the 1210T series except for the material variety, the sideflexing radius and the
available accessories
Designed for bi-directional travel
Chain data
Habasit code
C3210K0224DPTA-001
C3210K0224DPTA-002
C3210K0224DPTA-008
C3210K0224NYTA-008
Width W
mm
57.0
57.0
57.0
57.0
Weight
inch
2.24
2.24
2.24
2.24
kg/m
1.35
1.35
1.35
1.13
lb/ft
0.91
0.91
0.91
0.75
Material
DP
DP
DP
NY
Related products
Solid sprockets Series 3200
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain NH78 (straight)
88
Description
Straight running plastic chain
Designed for bi-directional travel
Robust heavy duty design for demanding applications like sewage treatment
Chain data
Habasit code
CNH78P0291LFAA
Width W
mm
74.0
Weight
inch
2.91
kg/m
2.10
lb/ft
1.41
Material
LF
Related products
Solid sprockets Series NH78
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain accessories
89
Description
Different accessories for case chains are available, including extended pins, pushers and attachment points.
Extended pin EP (only for straight running chains)
Extended journal pins (standard material is stainless steel SA) are
particularly advantageous for low tension accumulation, eliminating
damage to product and containers.
Chain type
Chain pitch P
Pin diam. D
Pin length L
mm
inch
mm
inch
C1100P100EP--AA---1
25.4
1.00
6.4
1/4 = 0.25
C1150P165EP--AA---1
38.1
1.50
6.4
1/4 = 0.25
C1200P224EP--AA---3
C1200P224EP--AA---8
C1250P225EP--AA---7
C1250P225EP--AA---8
50.8
2.00
63.5
2.50
66.3
2.61
CNH78P291EP--AA---7
CNH78P291EP--AA---8
CNH78P291EP--AA---9
9.5
3/8 = 0.38
12.7
8/16 = 0.50
11.1
7/16 = 0.44
12.7
8/16 = 0.50
11.11
7/16 = 0.44
12.7
8/16 = 0.50
14.3
9/16 = 0.56
mm
inch
38.1
1.50
Chain pitch P
mm
inch
50.8
2.00
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain accessories
90
Chain pitch P
mm
inch
C1100P100K1--AA---
25.4
1.00
C1150P165K1--AA---
38.1
1.50
C1200P224K1--AA---
50.8
2.00
Chain type
A
mm
6.9
B
inch
0.27
mm
inch
15.9
0.63
19.1
0.75
28.9
E
mm
inch
1.9
0.07
1.14
2.7
0.11
mm
inch
mm
inch
mm
inch
mm
inch
C1100P100K1--AA---
11.5
0.45
4.1
0.16
10.9
0.43
18
0.71
C1150P165K1--AA---
17.5
0.69
6.9
0.27
12.1
0.48
21
0.83
C1200P224K1--AA---
20.3
0.80
7.5
0.29
15.2
0.60
28.9
1.14
Tab type K2
Molded tab on both sides with two holes.
Chain type
C1200P224K2--AA--C1200P224K2--AA---
Chain pitch P
mm
inch
50.8
2.00
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain accessories
91
Tab type A1
Molded tab on one side with one hole.
Chain type
Chain pitch P
mm
inch
mm
inch
mm
inch
mm
inch
C1100P100A1--AA---
25.4
1.00
10.4
0.41
10.9
0.43
2.3
0.09
C1150P165A1--AA---
38.1
1.00
15.2
0.60
18.8
0.74
5.1
0.20
C1200P224A1--AA---
50.8
2.00
17.5
0.69
19.3
0.76
6.4
0.25
C1250P225A1--AA---
63.5
2.50
19.1
0.75
29
1.14
7.4
0.29
Chain type
mm
inch
mm
inch
mm
inch
mm
inch
C1100P100A1--AA---
11.4
0.45
5.2
0.21
4.1
0.16
3.2
0.13
C1150P165A1--AA---
17.5
0.69
7.6
0.30
6.0
0.24
5.1
0.20
C1200P224A1--AA---
20.3
0.80
8.8
0.35
6.8
0.27
6.4
0.25
C1250P225A1--AA---
31.8
1.25
9.6
0.38
12.5
0.49
6.4
0.25
Tab type A2
Molded tab on both sides with one hole.
Chain type
Chain pitch P
mm
inch
mm
inch
mm
inch
mm
inch
C1200P224A2--AA---
50.8
2.00
17.5
0.69
19.3
0.76
6.4
0.25
C1250P225A2--AA---
63.5
2.50
19.1
0.75
29
1.14
7.4
0.29
mm
inch
mm
inch
mm
inch
mm
inch
C1200P224A2--AA---
20.3
0.80
8.8
0.35
6.8
0.27
6.4
0.25
C1250P225A2--AA---
31.8
1.25
9.6
0.38
12.5
0.49
6.4
0.25
Chain type
4185BRO.CHA-en1115HQR
HabaCHAIN
Case chain accessories
92
Cone attachment CT
Cone Line Module for case chain 1200 (Straight).
Standard material is NY white
Chain type
C1200P224CT--AA---
Chain pitch P
0.75" thread
diam. A
Thread length
min.
mm
inch
mm
inch
mm
inch
50.8
2.00
19.1
0.75
25.4
1.00
4185BRO.CHA-en1115HQR
HabaCHAIN
Multi-Hub sprockets and idlers
93
Description
Habasit has invented a new type of modular
split sprockets and split idlers called Multi-Hub.
Interchangeable hub inserts in various diameters with
or without keyway and sprocket, or idler rims in two
different materials, reduce the inventory needed by
customers. With this Multi-Hub system it is possible
to combine a noise dampening sprocket rim with a
stiff and wear resistant hub. The customized choice of
materials and high fabrication accuracy ensure long
lifetime and optimized power transmission.
Complete Multi-Hub sprocket in noise dampening
material ND
1.
2.
3.
4.
5.
4185BRO.CHA-en1115HQR
HabaCHAIN
Multi-Hub 820 sprocket rims
94
Description
Multi-Hub 820 sprocket rim is suitable for 810, 820 and 831 series chains
The split sprocket rim has molded guide rings
Different bore configurations can be obtained by using separate Multi-Hub inserts
Sprocket data
Habasit code
Number of teeth
C0820G218
C0820G238
C0820G258
C0820G217
C0820G237
C0820G257
21
23
25
21
23
25
DE
mm
128.9
142.0
153.8
128.9
142.0
153.8
inch
5.07
5.59
6.06
5.07
5.59
6.06
Diam. of pitch dp
mm
inch
129.3
5.09
141.2
5.56
153.2
6.03
129.3
5.09
141.2
5.56
153.2
6.03
Material
GS
GS
GS
ND
ND
ND
4185BRO.CHA-en1115HQR
HabaCHAIN
Multi-Hub 820 idler rims
95
Description
Multi-Hub 820 idler rim is suitable for all 810, 820, 828, 831, 879B, 880B, 880J, 880LJ, 880M, 881B and
1061M series chains
Different bore configurations can be obtained by using separate Multi-Hub inserts
Sprocket data
Habasit code
C0820L219
C0820L239
C0820L259
Equivalent number of
teeth
21
23
25
DE
mm
130.0
142.5
154.5
Material
inch
5.12
5.61
6.08
L
L
L
4185BRO.CHA-en1115HQR
HabaCHAIN
Multi-Hub 821 sprocket rims
96
Description
Multi-Hub 821 sprocket rim is suitable for 800 and 821 series chains
Consisting of two Multi-Hub 881 sprockets set up side-by-side
Different bore configurations can be obtained by using separate Multi-Hub inserts
Sprocket data
Habasit code
Number of teeth
C0821G258
C0821G257
25
25
DE
mm
153.8
153.8
inch
6.06
6.06
Diam. of pitch dp
mm
inch
153.2
6.03
153.2
6.03
Material
GS
ND
Included in delivery: 4 sprocket rim halves (881 type), 8 screws, 8 self-locking nuts
Nuts and screws: stainless steel
Special noise dampening material available: ND
Related products
Multi-Hub inserts
4185BRO.CHA-en1115HQR
HabaCHAIN
Multi-Hub 880 sprocket rims
97
Description
Multi-Hub 880 sprocket rim is suitable for 828, 879, 880 and 890 series chains
Different bore configurations can be obtained by using separate Multi-Hub inserts
Sprocket data
Habasit code
Number of teeth
C0880G108
C0880G128
C0880G107
C0880G127
10
12
10
12
DE
mm
122.2
147.4
122.2
147.4
inch
4.81
5.80
4.81
5.80
Diam. of pitch dp
mm
inch
123.3
4.85
147.2
5.80
123.3
4.85
147.2
5.80
Material
GS
GS
ND
ND
4185BRO.CHA-en1115HQR
HabaCHAIN
Multi-Hub 881 sprocket rims
98
Description
Multi-Hub 881 sprocket rim is suitable for 881 series chains
Different bore configurations can be obtained by using separate Multi-Hub inserts
Sprocket data
Habasit code
Number of teeth
C0881G258
C0881G257
25
25
DE
mm
153.8
153.8
inch
6.06
6.06
Diam. of pitch dp
mm
inch
153.2
6.03
153.2
6.03
Material
GS
ND
4185BRO.CHA-en1115HQR
HabaCHAIN
Multi-Hub 882 sprocket rims
99
Description
Multi-Hub 882 sprocket rim is suitable for 882 series chains
Different bore configurations can be obtained by using separate Multi-Hub inserts
Sprocket data
Habasit code
Number of teeth
C0882G128
C0882G127
12
12
DE
mm
150.0
150.0
inch
5.91
5.91
Diam. of pitch dp
mm
inch
147.2
5.80
147.2
5.80
Material
GS
ND
4185BRO.CHA-en1115HQR
HabaCHAIN
Multi-Hub 1060 sprocket rims
100
Description
Multi-Hub 1060 sprocket rim is suitable for 770 and 1061 series chains
Different bore configurations can be obtained by using separate Multi-Hub inserts
Sprocket data
Habasit code
Number of teeth
C1060G168
C1060G188
C1060G167
C1060G187
16
18
16
18
DE
mm
133.0
149.2
133.0
149.2
inch
5.24
5.87
5.24
5.87
Diam. of pitch dp
mm
inch
130.2
5.13
146.3
5.76
130.2
5.13
146.3
5.76
Material
GS
GS
ND
ND
4185BRO.CHA-en1115HQR
HabaCHAIN
Multi-Hub inserts
101
Description
Available with round bore only (RL type) or with metric keyway according to ISO standard or imperial keyway
according to ANSI standard (RZ type) or square bore (QZS type).
RZ types are designed to clamp on standard shafts and are suitable for drive applications with all Multi-Hub
sprocket rims
QZS types need retainer rings for axial fixation.
RL types are designed to spin free on standard shafts
RL types consist of extra low friction POM (Acetal) material for optimal sliding properties
RL type inserts can be used for Multi-Hub sprocket rims (intended to be used as an idler) and Multi-Hub idler rims
Set screw fixation option for imperial bores only.
Sprocket data
Habasit code
Insert type
Bore size d
mm
inch
mm
t
inch
mm
Bore shape
H025RZ-8
Drive
25.0
8.0
28.3
H030RZ-8
Drive
30.0
8.0
33.3
H035RZ-8
Drive
35.0
10.0
38.3
H040RZ-8
Drive
40.0
12.0
43.3
H040QZS84
Drive
40.0
H100RZ-8
Drive
0.25
1.12
H125RZ-8
Drive
1 1/4
0.25
1.37
H144RZ-8
Drive
1 7/16
0.38
1.61
H150RZ-8
Drive
1 1/2
0.38
1.67
H150QZS84
H025RL
H030RL
H035RL
H040RL
H100RL
H125RL
H144RL
H150RL
Drive
Idler
Idler
Idler
Idler
Idler
Idler
Idler
Idler
1 1/2
25.0
30.0
35.0
40.0
1
1 1/4
1 7/16
1 1/2
Material
inch
Round with
GS
keyway
Round with
GS
keyway
Round with
GS
keyway
Round with
GS
keyway
Square
GS
Round with
GS
keyway
Round with
GS
keyway
Round with
GS
keyway
Round with
GS
keyway
Square
GS
Round
L
Round
L
Round
L
Round
L
Round
L
Round
L
Round
L
Round
L
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 600
102
Description
Solid sprocket 600 is suitable for all 600 series chains
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
C0600M06PE
C0600M08PE
C0600M10PE
C0600M12PE
C0600M14PE
Number of teeth
6
8
10
12
14
DE
mm
128.0
168.9
210.1
248.3
288.4
inch
5.04
6.65
8.29
9.78
11.35
Diam. of pitch dp
mm
inch
127.0
5.00
165.9
6.53
205.5
8.09
245.3
9.66
285.4
11.24
Material
PE
PE
PE
PE
PE
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 810
103
Description
Solid sprocket 810 is suitable for all 810 series chains
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
Number of
teeth
C0810M19NY
C0810M21CI
C0810M21NY
C0810M23CI
C0810M23NY
C0810M25CI
C0810M25NY
C0810M27NY
19
21
21
23
23
25
25
27
DE
mm
117.1
130.1
130.1
142.0
142.0
154.2
154.2
166.6
Diam. of pitch dp
inch
4.61
5.12
5.12
5.59
5.59
6.07
6.07
6.56
mm
117.4
129.3
129.3
141.2
141.2
153.2
153.2
165.2
inch
4.62
5.09
5.09
5.56
5.56
6.03
6.03
6.50
L
mm
42.9
43.5
42.9
43.5
42.9
43.5
42.9
42.9
mm
19.0
20.0
19.0
20.0
19.0
20.0
19.0
19.0
inch
0.75
0.79
0.75
0.79
0.75
0.79
0.75
0.75
Material
NY
CI
NY
CI
NY
CI
NY
NY
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid idlers Series 810
104
Description
Solid idler 810 is suitable for all 810, 820, 828, 831, 879B, 880B, 880J, 880LJ, 880M, 881B and 1061M series
chains
Standard idler has a pilot bore
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
Equivalent number of
teeth
C0810L17PE
C0810L19PE
C0810L27PE
17
19
27
DE
mm
105.0
117.1
166.6
Material
inch
4.13
4.61
6.56
PE
PE
PE
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 820
105
Description
Solid sprocket 820 is suitable for all 810, 820 and 831 series chains
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
Number of
teeth
C0820M17NY
C0820M19NY
C0820M21CI
C0820M21NY
C0820M23CI
C0820M23NY
C0820M25CI
C0820M25NY
C0820M27NY
17
19
21
21
23
23
25
25
27
DE
mm
105.2
117.1
130.1
130.1
142.0
142.0
154.2
154.2
166.6
inch
4.14
4.61
5.12
5.12
5.59
5.59
6.07
6.07
6.56
Diam. of pitch dp
mm
105.5
117.4
129.3
129.3
141.2
141.2
153.2
153.2
165.2
mm
19.0
19.0
20.0
19.0
20.0
19.0
20.0
19.0
19.0
inch
4.15
4.62
5.09
5.09
5.56
5.56
6.03
6.03
6.50
inch
0.75
0.75
0.79
0.75
0.79
0.75
0.79
0.75
0.75
Material
NY
NY
CI
NY
CI
NY
CI
NY
NY
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 821
106
Description
Solid sprocket 821 is suitable for all 800 and 821 series chains
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
Number of
teeth
C0821M19NY
C0821M21CI
C0821M21NY
C0821M23CI
C0821M23NY
C0821M25CI
C0821M25NY
C0821M27NY
C0821M29NY
19
21
21
23
23
25
25
27
29
DE
mm
117.1
130.1
130.1
142.0
142.0
154.2
154.2
166.6
179.1
Diam. of pitch dp
inch
4.61
5.12
5.12
5.59
5.59
6.07
6.07
6.56
7.05
mm
117.4
129.3
129.3
141.2
141.2
153.2
153.2
165.2
177.3
inch
4.62
5.09
5.09
5.56
5.56
6.03
6.03
6.50
6.98
L
mm
79.2
80.0
79.2
80.0
79.2
80.0
79.2
79.2
79.2
Material
inch
3.12
3.15
3.12
3.15
3.12
3.15
3.12
3.12
3.12
NY
CI
NY
CI
NY
CI
NY
NY
NY
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 880
107
Description
Solid sprocket 880 is suitable for all 828, 879, 880 and 890 series chains
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
Number of
teeth
C0880M09NY
C0880M10NY
C0880M11NY
C0880M12CI
C0880M12NY
C0880M13NY
C0880M14NY
C0880M15NY
9
10
11
12
12
13
14
15
DE
mm
112.4
125.0
137.5
149.9
149.9
162.3
174.7
186.9
inch
4.43
4.92
5.41
5.90
5.90
6.39
6.88
7.36
Diam. of pitch dp
mm
111.4
123.3
135.2
147.2
147.2
159.2
171.2
183.1
mm
19.0
19.0
19.0
20.0
19.0
19.0
19.0
19.0
inch
4.39
4.85
5.32
5.80
5.80
6.27
6.74
7.21
inch
0.75
0.75
0.75
0.79
0.75
0.75
0.75
0.75
Material
NY
NY
NY
CI
NY
NY
NY
NY
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 881
108
Description
Solid sprocket 881 is suitable for all 881 series chains
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
Number of
teeth
C0881M19NY
C0881M21CI
C0881M21NY
C0881M23CI
C0881M23NY
C0881M25CI
C0881M25NY
C0881M27NY
19
21
21
23
23
25
25
27
DE
mm
117.1
130.1
130.1
142.0
142.0
154.2
154.2
166.6
Diam. of pitch dp
inch
4.61
5.12
5.12
5.59
5.59
6.07
6.07
6.56
mm
117.4
129.3
129.3
141.2
141.2
153.2
153.2
165.2
inch
4.62
5.09
5.09
5.56
5.56
6.03
6.03
6.50
L
mm
31.8
31.0
31.8
31.0
31.8
31.0
31.8
31.8
mm
19.0
20.0
19.0
20.0
19.0
20.0
19.0
19.0
inch
0.75
0.79
0.75
0.79
0.75
0.79
0.75
0.75
Material
NY
CI
NY
CI
NY
CI
NY
NY
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 882
109
Description
Solid sprocket 882 is suitable for all 882 series chains
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
Number of
teeth
C0882M09NY
C0882M10CI
C0882M10NY
C0882M11NY
C0882M12CI
C0882M12NY
C0882M13NY
C0882M14NY
C0882M15NY
9
10
10
11
12
12
13
14
15
DE
mm
112.4
125.0
125.0
137.5
149.9
149.9
162.3
174.7
186.9
Diam. of pitch dp
inch
4.43
4.92
4.92
5.41
5.90
5.90
6.39
6.88
7.36
mm
111.4
123.3
123.3
135.2
147.2
147.2
159.2
171.2
183.1
inch
4.39
4.85
4.85
5.32
5.80
5.80
6.27
6.74
7.21
Material
NY
CI
NY
NY
CI
NY
NY
NY
NY
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 1100
110
Description
Solid sprocket 1100 is suitable for all 1100 series chains
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
Number of
teeth
C1100M07PE
C1100M09PE
C1100M10PE
C1100M11PE
C1100M12PE
C1100M14PE
C1100M15PE
C1100M16PE
C1100M17PE
C1100M19PE
7
9
10
11
12
14
15
16
17
19
Diam. of pitch dp
mm
59.0
74.0
82.0
90.0
98.0
114.0
122.0
130.0
138.0
154.0
inch
2.32
2.91
3.23
3.54
3.86
4.49
4.80
5.12
5.43
6.06
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
Material
E
E
E
E
E
E
E
E
E
E
PE
PE
PE
PE
PE
PE
PE
PE
PE
PE
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 1150
111
Description
Solid sprocket 1150 is suitable for all 1150 series chains
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
Number of
teeth
C1150M07PE
C1150M09PE
C1150M10PE
C1150M12PE
C1150M14PE
C1150M15PE
C1150M16PE
C1150M17PE
7
9
10
12
14
15
16
17
Diam. of pitch dp
mm
88.0
112.0
123.0
147.0
159.0
183.0
195.0
207.0
inch
3.46
4.41
4.84
5.79
6.26
7.20
7.68
8.15
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
Material
E
E
E
E
E
E
E
PE
PE
PE
PE
PE
PE
PE
PE
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 1200
112
Description
Solid sprocket 1200 is suitable for all 1200 and 3200 series chains
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
C1200M08PE
C1200S08PE
C1200S08NY
C1200M12PE
C1200S12NY
C1200S12PE
C1200M15NY
C1200M15PE
C1200S17NY
C1200S17PE
Material
E
M
M
E
M
M
A
A
B
B
C
C
E
E
M
M
PE
PE
NY
PE
NY
PE
NY
PE
NY
PE
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 1250
113
Description
Solid sprocket 1250 is suitable for all 1250 series chains
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
Number of
teeth
C1250M08PE
C1250M12PE
C1250M15PE
C1250M17PE
8
12
15
17
Diam. of pitch dp
mm
166.0
245.0
306.0
346.0
inch
6.54
9.65
12.05
13.62
A
A
A
A
B
B
B
B
C
C
C
C
Material
E
E
E
E
PE
PE
PE
PE
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 1400
114
Description
Solid sprocket 1400 is suitable for all 1400 series chains
Bore configurations can be machined according to the customer requirements
43.0
Sprocket data
Habasit code
C1400M06PE
C1400M08PE
C1400M10PE
Number of teeth
6
8
10
DE
mm
177.0
227.6
279.0
inch
6.97
8.96
10.98
Diam. of pitch dp
mm
inch
165.0
6.50
215.6
8.49
267.0
10.51
Material
PE
PE
PE
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 1700
115
Description
Solid sprocket 1700 is suitable for all 1700 series chains
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
C1700M08PE
C1700M10PE
C1700M12PE
C1700M13PE
Number of teeth
8
10
12
13
DE
mm
133.0
166.1
196.0
214.0
inch
5.24
6.54
7.72
8.43
Diam. of pitch dp
mm
inch
130.6
5.14
161.8
6.37
193.2
7.61
208.9
8.22
Material
PE
PE
PE
PE
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 3200
116
Description
Solid sprocket 3200 is suitable for all 3200 and 1200 series chains
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
C3200M08NY
C3200M08PE
C3200Z08NY
C3200Z08PE
C3200M10NY
C3200M10PE
C3200M12NY
C3200M12PE
C3200S1240Q6
C3200S1203Q6
C3200M15NY
C3200M15PE
C3200M17NY
C3200M17PE
C3200M19NY
C3200M19PE
Number of
teeth
8
8
8
8
10
10
12
12
12
12
15
15
17
17
19
19
Diam. of pitch dp
mm
132.2
132.2
132.2
132.2
163.8
163.8
195.5
195.5
195.5
195.5
243.4
243.4
275.4
275.4
307.5
307.5
inch
5.21
5.21
5.21
5.21
6.45
6.45
7.70
7.70
7.70
7.70
9.58
9.58
10.84
10.84
12.11
12.11
A
A
A
A
A
A
A
A
Material
C
C
C
C
C
C
C
C
NY
PE
NY
PE
NY
PE
NY
PE
PT
PT
NY
PE
NY
PE
NY
PE
M
M
A
A
A
A
A
A
C
C
C
C
C
C
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series 7100
117
Description
For each 7100 series chain width one different solid sprocket 7100 is available
Standard sprocket has a 25 mm bore with keyway
Sprocket data
Habasit code
Number
of teeth
DE
Diam. of pitch dp
Bore size d
C7100M16NY00R2
C7100M16NY25R2
16
16
mm
132.7
132.7
inch
5.22
5.22
mm
130.2
130.2
inch
5.20
5.20
mm
38.0
38.0
inch
1.50
1.50
mm
20.0
25.0
inch
0.79
0.98
C7100M16NY40Q2
C7100M12NY00R3
C7100M12NY25R3
16
12
12
132.7
138.3
138.3
5.22
5.44
5.44
130.2
129.2
129.2
5.20
5.09
5.09
38.0
50.3
50.3
1.50
1.98
1.98
40.0
20.0
25.0
1.57
0.79
0.98
C7100M12NY40Q3
C7100M12NY00R4
C7100M12NY25R4
12
12
12
138.3
145.5
145.5
5.44
5.73
5.73
129.2
137.4
137.4
5.09
5.41
5.41
50.3
65.0
65.0
1.98
2.56
2.56
40.0
20.0
25.0
1.57
0.79
0.98
C7100M12NY40Q4
12
145.5
5.73
137.4
5.41
65.0
2.56
40.0
1.57
Bore
shape
Material
Round
Round
with keyway
Square
Round
Round
with keyway
Square
Round
Round
with keyway
Square
NY
NY
NY
NY
NY
NY
NY
NY
NY
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid idlers Series 7100
118
Description
For each 7100 series chain width one different solid idler 7100 is available
Standard idler has two 35 mm bores for bearings
Sprocket data
Habasit code
C7100L16NY15R2
C7100L16NY35R2
C7100L12NY15R3
C7100L12NY35R3
C7100L12NY15R4
C7100L12NY35R4
Equivalent
number of
teeth
16
16
12
12
12
12
DE
mm
119.5
119.5
117.8
117.8
123.0
123.0
inch
4.70
4.70
4.64
4.64
4.84
4.84
mm
inch
35.0
1.38
35.0
1.38
35.0
1.38
mm
38.0
38.0
50.0
50.0
70.5
70.5
inch
1.50
1.50
1.97
1.97
2.78
2.78
mm
25.0
25.0
33.8
33.8
49.0
49.0
Bore size d
inch
0.98
0.98
1.33
1.33
1.93
1.93
mm
15.2
31.0
15.2
31.0
15.2
31.0
inch
0.60
1.22
0.60
1.22
0.60
1.22
Material
NY
NY
NY
NY
NY
NY
4185BRO.CHA-en1115HQR
HabaCHAIN
Solid sprockets Series NH78
119
Description
Solid sprocket NH78 is suitable for all NH78 series chains
Bore configurations can be machined according to the customer requirements
43.0
Sprocket data
Habasit code
CNH78M06PE
CNH78M08PE
CNH78M10PE
Number of teeth
6
8
10
DE
mm
142.5
183.2
224.4
inch
5.61
7.21
8.83
Diam. of pitch dp
mm
inch
132.5
5.22
173.2
6.82
214.4
8.44
Material
PE
PE
PE
4185BRO.CHA-en1115HQR
HabaCHAIN
Split sprockets Series 1061
120
Description
Split sprocket 1061 is suitable for 770 and 1061 series chains
For teeth number 16 and 18 see Multi-Hub 1060 sprocket
Bore configurations can be machined according to the customer requirements
Sprocket data
Habasit code
C1061Z14NY
C1061Z15NY
C1061Z17NY
C1061Z19NY
C1061Z20NY
Number of teeth
14
15
17
19
20
DE
mm
116.8
124.8
140.8
156.8
164.8
inch
4.60
4.91
5.54
6.17
6.49
Diam. of pitch dp
mm
inch
113.8
4.48
121.8
4.80
137.8
5.43
153.8
6.06
161.9
6.37
Material
NY
NY
NY
NY
NY
4185BRO.CHA-en1115HQR
HabaCHAIN
Retainer rings
121
Description
For axial fixation of sprockets and idlers
Easy installation from one side, no shaft turning for screw fixing necessary
Sprocket data
Habasit code
M00C0020R13+GF
mm
44.0
A
inch
1.73
mm
14.0
C
inch
0.55
Bore size d
mm
inch
20.0
M00C0025R13+GF
49.0
1.93
14.0
0.55
25.0
1.0
M00C0030R13+GF
54.0
2.13
14.0
0.55
30.0
1.19
M00C0040Q13+GF
M00C0060Q13+GF
M00C0002Q13+GF
M00C0003Q13+GF
M00C0005Q13+GF
66.0
86.0
52.0
65.0
90.0
2.60
3.39
2.05
2.56
3.54
16.0
18.0
14.0
16.0
18.0
0.63
0.71
0.55
0.63
0.71
40.0
60.0
25.4
1.0
1.5
2.5
Bore shape
Material
Round
with keyway
Round
with keyway
Round
with keyway
Square
Square
Square
Square
Square
PP
PP
PP
PP
PP
PP
PP
PP
4185BRO.CHA-en1115HQR
122
Appendix
Chemical resistance Plastics
The data presented in the following table is based on information provided by the raw material manufacturers
and suppliers. It does not replace the need to test the products for your application.
In individual cases, the stability of the material in the medium in question must be examined.
Acetone
Aluminum Comp.
Ammonia
Ammonium Comp.
Aniline
Aqua Regia
Arsenic Acid
Barium Comp.
Beer
Benzene
Benzoic Acid
Borax
Boric Acid
Brine 10 %
Butyl Acrylate
Butyric Acid
Carbon Dioxide
Carbon Disulfide
Carbon Tetrachloride
Chloracetic Acid
Chlorine Gas
Chlorine Liquid
Chlorobenzene
Chloroform
Chromic Acid 3%
NGNPN pin
60 C (140 F)
20 C (70 F)
60 C (140 F)
20 C (70 F)
ND
Acetic Acid 5%
60 C (140 F)
60 C (140 F)
20 C (70 F)
20 C (70 F)
20 C (70 F)
60 C (140 F)
60 C (140 F)
DPLFPTTS
PKECDE
20 C (70 F)
60 C (140 F)
Chemical
20 C (70 F)
PE
PP
Materials
WRNYHT
L pinGS
4185BRO.CHA-en1115HQR
123
Appendix
Chemical resistance Plastics
Corn Oil
Cottonseed Oil
Cresol
Cyclohexane
Cyclohexanol
Cyclohexanone
Detergents
Dextrin
Dibutyl Phthalate
Diisooctyl Phthalate
Dimethyl Phthalate
Dimethylamine
Dioctyl Phthalate
NGNPN pin
Ethyl Acetate
Ethyl Ether
Ethylamine
Formaldehyde 37%
Freon
60 C (140 F)
20 C (70 F)
Copper Comp.
60 C (140 F)
20 C (70 F)
ND
60 C (140 F)
20 C (70 F)
20 C (70 F)
60 C (140 F)
Diethylamine
60 C (140 F)
20 C (70 F)
Coconut Oil
20 C (70 F)
60 C (140 F)
Citrus Juices
Diethyl Ether
60 C (140 F)
DPLFPTTS
PKECDE
Chemical
20 C (70 F)
PE
PP
Materials
WRNYHT
L pinGS
Fuel Oil # 2
Fruit Juices
Furfural
Gasoline
Glucose
Glycerol
Heptane
Hexane
4185BRO.CHA-en1115HQR
124
Appendix
Chemical resistance Plastics
Hydrogen Sulfide
Igepal 50%
Iodine Crystals
Isooctane
Isopropyl Alcohol
Jet Fuel
Kerosene
Lactic Acid
Lanolin
Lauric Acid
Lead Acetate
Linseed Oil
Lubricating Oil
Magnesium Comp.
Manganese Sulfate
Margarine
Mercury
Methyl Chloride
Methylsulfuric Acid
Methylene Chloride
Milk
Mineral Oil
Mineral Spirits
Molasses
Motor Oil
Naphtha
NGNPN pin
Nitrobenzene
Nitrous Acid
Nitrous Oxide
Oleic Acid
60 C (140 F)
20 C (70 F)
60 C (140 F)
20 C (70 F)
ND
20 C (70 F)
20 C (70 F)
20 C (70 F)
Hydrogen Peroxide 3%
60 C (140 F)
60 C (140 F)
60 C (140 F)
DPLFPTTS
PKECDE
60 C (140 F)
20 C (70 F)
Chemical
20 C (70 F)
60 C (140 F)
PE
PP
Materials
WRNYHT
L pinGS
4185BRO.CHA-en1115HQR
125
Appendix
Chemical resistance Plastics
Paraffin
Peanut Oil
NGNPN pin
60 C (140 F)
20 C (70 F)
60 C (140 F)
Ozone
20 C (70 F)
ND
60 C (140 F)
20 C (70 F)
60 C (140 F)
60 C (140 F)
20 C (70 F)
20 C (70 F)
Oxalic Acid
60 C (140 F)
DPLFPTTS
PKECDE
60 C (140 F)
Olive Oil
20 C (70 F)
Chemical
20 C (70 F)
PE
PP
Materials
WRNYHT
L pinGS
Perchlorothylene
Phenol
Phenol 5 %
Photographic Solutions
Plating Solutions
Potassium Comp.
Potassium Hydroxide
Potassium Permanganate
Silver Cyanide
Silver Nitrate
Sodium Comp.
Sodium Chlorite
Sodium Hypochlorite 5%
Stearic Acid
Sulfate Liquors
Sulfur
Sulfur Chloride
Sulfur Dioxide
Tartaric Acid
Sulfurous Acid
4185BRO.CHA-en1115HQR
126
Appendix
Chemical resistance Plastics
Transformer Oil
Tributyl Phosphate
Trichloroacetic Acid
Trichloroethylene
Tricresyl Phosphate
Trisodium Phosphate
Turpentine
Urea
Vinegar
Wine
Xylene
NGNPN pin
60 C (140 F)
20 C (70 F)
60 C (140 F)
20 C (70 F)
20 C (70 F)
60 C (140 F)
ND
60 C (140 F)
Toluene
20 C (70 F)
20 C (70 F)
Tetrahydrofuran
60 C (140 F)
DPLFPTTS
PKECDE
60 C (140 F)
20 C (70 F)
Chemical
20 C (70 F)
60 C (140 F)
PE
PP
Materials
WRNYHT
L pinGS
The data in this table is taken from laboratory tests, performed on unstrained test samples. It should be
considered as purely indicative, since material behavior under real working conditions depends on different
factors, including: temperature, concentration of the chemical agent, and speed or long-lasting effect of the
chemical agent.
With thermoplastic products, do not use cleaning or lubricating agents with pH values below 4 or above 10.
4185BRO.CHA-en1115HQR
127
Appendix
Chemical resistance Steel
Linseed Oil
Magnesium Comp.
Malic Acid 50%
Margarine
Mercury
Methyl Ethyl Ketone
Methylene Chloride
Milk
Mineral Oil
Motor Oil
Nitric Acid 25%
Nitric Acid 50%
Oleic Acid
Olive Oil
Oxalic Acid
Ozone
Palmitic Acid 70%
Phenol
Phosphoric Acid 25%
Phosphoric Acid 50%
Photographic Solutions
Potassium Hydroxide
Siver Nitrate
Soap and water
Sodium Chlorite
Sodium Hydroxide
Sodium Hydroxide 60%
Sodium Hypo-chlorite (5% CI)
Sulfur
Sulfur Dioxide (dry)
Sulfur Dioxide (wet)
Sulfuric Acid 10%
Sulfuric Acid 50%
Sulfuric Acid 70%
Tannic Acid 10%
Tartaric Acid
Toluene
Transformer Oil
Turpentine
Urea
Vinegar
Whisky
Wine
Xylene
SA
IN
60 C (140 F) P, Q
20 C (70 F)
SS
SH
60 C (140 F) K
Chemical
20 C (70 F)
SA
IN
60 C (140 F) P, Q
20 C (70 F)
Chemical
Materials
SS
SH
60 C (140 F) K
Materials
20 C (70 F)
4185BRO.CHA-en1115HQR
Appendix
Safety information
When connecting or disconnecting a chain, always
turn off and lock out the power switch before starting.
Always use goggles to protect your eyes. Wear
protective clothing, gloves and safety shoes. Support
the chain to prevent uncontrolled movements. Use
appropriate tools in good working condition, and
use the correctly in a proper manner. Do not attempt
to connect or disconnect the chain without full
knowledge of the chain construction, including the
correct procedure for pin removal or insertion.
All pinch and shear points, along with all other
exposed moving parts that pose a potential hazard to
people at workstations or on conveyor passageways,
must be safeguarded.
Overhead conveyors must have guards to prevent
objects from falling. Cleated conveyor chains are more
hazardous, creating pinch and shear points.
Safeguarding can be achieved by:
Identification
Identify all hazardous areas that pose a danger to
personnel.
Guard barriers
Place guard barriers to prevent entry into the
hazardous area, and apply guards to high conveyors to
prevent objects from falling on to personnel below.
Control devices
Set machine controls to prevent hazardous operations/
conditions.
Warnings
Use instructions, warning labels, or sound/light signals
to alert that a hazardous condition exists.
Safeguarding should be designed to minimize any
discomfort or difficulties for operators. Bypassing
and/or overriding safeguarding mechanisms during
operation should not be allowed.
Any safeguarding concerns regarding the conveyor
should be addressed during the design process.
Product safety
Products designed and manufactured by Habasit can
128
Notes
129
Customers first
At Habasit we understand that our success depends
on your success. This is why we offer solutions, not
just products; partnership, not just sales.
Since our foundation in 1946, Habasit has brought
this understanding of customer needs to life every
day and for every application. Thats why were the
No. 1 in belting today. Worldwide.
Learn more at www.habasit.com
Committed to innovation
Because our customers' belting challenges and
needs never cease, we consistently dedicate a
substantial percentage of our employees and
resources to the research and development of new
products and solutions.
Certified for quality
We deliver the highest quality standards
not only in our products and solutions,
but also in our employees daily work
processes. Habasit AG is certified
according to ISO 9001:2008.
Fabric-based conveyor
and processing belts
HabaFLOW
Power transmission
belts
HabaDRIVE
Timing belts
HabaSYNC
Machine tapes
Round belts
Seamless belts
Profiles, Guides,
Wear strips
HabiPLAST
Fabrication tools
(joining tools)
Gearmotors
Electric motors
Motion control