Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Adbri Masonry
Adbri Masonry is Australias leading masonry manufacturer supplying quality concrete bricks, blocks, pavers, retaining walls, erosion
control products, architectural masonry solutions and reconstituted stone veneers from 15 sites throughout New South Wales,
Queensland, Victoria, South Australia and Tasmania. Adbri Masonry is a wholly owned subsidiary of Adelaide Brighton Limited,
a leading integrated construction materials and lime producing group of companies and a member of the S&P/ASX 200 Index.
Adbri Masonry first produced concrete Besser blocks in 1957 and since then has traded as many household brand names including
Besser, Rocla Pavers and Masonry, Pioneer Building Products, Hanson Building Products Pty Ltd and C&M Brick before rebranding
as Adbri Masonry in 2009.
In addition to supplying a full collection of quality concrete building and landscaping products, there are a range of valuable
benefits to working with Adbri Masonry including;
Access to our Contracting Services Team (in-house design, supply, installation and certification team for commercial projects).
Confidence that all product lines are tested for quality in our N.A.T.A accredited laboratory
Support from experienced in-house engineers who can provide technical advice and design solutions for civil, commercial and
industrial projects
The ability to create customised product and colour solutions specific to individual projects (conditions apply).
adbri masonry
Contracting Services
CE
TI
SU
LL
FY
DESIGN
TA
Adbri Masonrys Contracting Services Division has been providing solutions in the market for over 20 years. PThey offer a range
of construction and project management services, including a complete design, supply, install and certificationYpackage I N
for segmental retaining walls, pavements, erosion control and wall cladding products.
Operating on the East Coast the Adbri Masonry team can provide the following civil contracting services;
Preliminary costings
Certified design
FY
INS
TA
DESIGN
LL
TI
SU
PL
Y
CE
By utilising these services, the quality and structural adequacy of the finished project can be professionally
managed and officially certified on your behalf.
QLD Building License Number - 61929
Please Note: These services are limited to commercial and industrial projects and are not available for residential works.
adbri masonry
Dimensions
wxdxh
(mm)
Vertica
Maximum Heights
No per m2
No per
tonne
Unit Weight
(kg)
11.1
26.04
38.4
Vertica Cap
2.74 L/m
52.36
19.1
Landmark Full
Tapered
Component
13.16
27
37
Landmark
Half Tapered
Component
26.32
43.4
23
Diamond Pro
175 pair unit
5.55*
28.57*
35*
Diamond Pro
275 pair unit
5.55*
28.57*
35*
Diamond Pro
Full unit
5.55
28.57
35
Diamond Pro
Capping Stone
2.20 L/m
52.36
19.1
Diamond
16.9
34.13
29.3
Cut Diamond
Balmoral
15
30.96
9.6
26.1
82.64
12.1
Windsor
26.1
72.46
13.8 (Tas)
Hampton Stone
15.32
38.46
26
Hampton Stone
Cap
450 x 250 x 70
2.3 L/m
59.38
Residential
Gravity
Walls
No Fines
Geogrid
1000mm
2000mm
12000mm
1:14 (4)
950mm
1900mm
20000mm
1:14 (4)
1000mm
2200mm
12000mm
1:8 (7.1)
2400mm
3000mm
8000mm
1:3 (18)
1040mm
1950mm
N/A
1:4 (14)
1050mm
1950mm
8000mm
1:5.4 (10.5)
Setback
16.84
*175 and 275 units are sold together with equal numbers of each on a pallet.
**150 and 250 units are sold together with equal numbers of each on a pallet.
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions
and requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown.
Product
Dimensions
wxdxh
(mm)
No per m2
No per
tonne
Unit
Weight
(kg)
Meadow Stone
150 pair
component
8.3 pairs**
66.67
Meadow Stone
250 pair
component
8.3 pairs**
111.1
15
Meadow Stone
400 full unit
8.3
50
20
Capping Stone
300 x 200 x 60
166.67
Eden Wall
76.92
13
Natural
Impressions
33.33
106.16
9.42
10
Maximum Heights
Residential
Gravity
Walls
No Fines
Geogrid
750mm
1800mm
N/A
1:8 (7.1)
1350mm
N/A
N/A
1:2.75 (20)
800mm
1500mm
N/A
1:5 (11.3)
800mm
1400mm
N/A
Setback
Natural
Impressions
Capping Unit
300 x 200 x 50
3.33 L/m
168.35
5.94
Versawall
Standard Unit
12.5
62.5
21.5
Versawall
Capping Unit
300 x 240 x 60
3.3L/m
106
9.6
Versawall
Corner Unit
62.5
21.5
Versastone
Standard Unit
12.5
65
15.3
600mm
1400mm
N/A
Versastone
Capping Unit
390 x 190 x 40
2.5L/m
143
7.00
Miniwall
44 Semi Solid
51 Solid
227.28
4.4
500mm
875mm
N/A
8 L/m
227.28
Minicap
4.4
Nominated maximum heights are based on designs provided in this literature. Should you have any taller walls, or walls that fall outside the scope of the provided designs, please contact
Adbri Masonry for assistance.
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions
and requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown.
adbri masonry
This brochure has been prepared by Adbri Masonry. All designs in this brochure have been checked and approved by Arlene Nardone, RPEQ 7777 and Wayne Holt CPEng, NPER, RPEQ 5510.
Disclaimer:
It is the responsibility of the customer to ensure that all assumed properties (Note 2 of Technical Parameters) are achieved on site, and that all retaining walls are installed as per requirements of designs and
cross sectional details. Adbri Masonry accepts no liability for any walls outside the scope of designs included in this brochure, or for installation of the products contained within.
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions
and requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown.
Unit Weight
(kN/m3)
Internal Friction
Angle ()
Cohesive Strength
Loading Code
19
30
Masonry Code
19
25
Gravel Backfill
19
37
Concrete
24
N/A
CGM
18
37
19
42
19
N/A
N/A
AS4678:2002
AS1170.1:2002
AS3700:2011
Aggregate
12 - 20mm max.
No Fines Concrete 6:1 ratio by volume of 20mm max size clean aggregate and
cement. Water content should be such that the cement
slurry evenly coats the aggregate and retains a wet/glossy
appearance without excess slurry running off. This is
typically around 40 litres per 100kg of cement.
(a) All retaining walls are designed to CMAA document MA53 (Segmental
Concrete Gravity Retaining Walls Design and Construction Guide).
(b) All retaining walls shall comply with AS4678 Structure Classification A.
(c) These tables are only applicable to retaining walls that incorporate a low
permeability surface membrane and drainage system such that there can
be no ingress of any water into the soil behind the retaining wall.
(d) Structures that do not incorporate a low permeability surface
membrane and drainage system such that there can be no ingress of
any water into the soil behind the retaining wall are deemed to be
outside the scope of this brochure.
(e) These tables are applicable to cuts in insitu soils. The tables are not
applicable to cohesive fill.
(f) All retaining walls are designed for a maximum surcharge load of
2.5 kPa. If surcharge loads greater than 2.5 kPa are expected, these
designs will not be appropriate.
(g) CGM leveling pads consist of at least 5% cement-stabilised crushed rock
with dimensions as detailed. Before the bottom course is positioned,
the footing should be moistened to ensure bond between block and
footing.
(h) These walls have been designed in accordance with Rankine Bell
Methodology.
5. The segmental retaining wall units in this brochure, with the exception of the
Landmark system, have keys which are utilised for locating purposes only and
are therefore not subject to the dimensional tolerances outlined in table 2.3
of AS4455.3:2008 Segmental Retaining Wall Units. The Landmark system
has been independently tested to ensure integrity of the structural key for the
purpose of constructing geogrid reinforced walls up to 20m in height.
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions
and requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown.
adbri masonry
adbri masonry
7. The base of the leveling pad excavation should be firm, dry and free of
loose material. Any disturbed ground at the base of the trench should
be compacted prior to footing construction. All retained material must
be compacted by firm tamping using appropriate compaction equipment.
Materials in front of the wall should be founding soil or equivalent and
thoroughly compacted immediately after the wall is out of the ground.
8. If the insitu material is equal to or exceeds the properties of the proposed
infill material, then the insitu material shall be substituted for the infill
material.
9. Precautions should be taken if cutting back the existing bank to ensure
such excavation does not destabilize the footing of another structure.
10. Walls may be constructed to greater heights in specific applications with
special engineering design.
11. Check with your local council whether building approval is required.
12. It is recommended that the top course is adhered to the next course with
a suitable waterproof construction adhesive as a precautionary measure.
Check with manufacturer of adhesive for suitability of use.
13. Where these walls impose loads on other structures those other
structures must be checked for strength and stability.
14. Where a foundation replacement zone is detailed, this will denote the
removal of natural material where detailed, and replacement with CBR45
road base compacted to 98% Standard Relative Dry Density (RDD).
15. External interface friction angle is calculated as being equal to 2/3 of the
internal interface friction angle.
16. Subsoil drains should be flushed at regular intervals to ensure continuous
proper functioning of the retaining wall drainage system.
17. Subsoil drains shall have outlet points at maximum 20m centres for dry
application and maximum 5m centres for wet application.
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
in deciding on the type of drainage required, but are not intended to replace
professional advice.
In the event of heavy rain before planting is established, the top of the wall
should be covered with plastic sheets or tarpaulins to prevent the soil being
scoured out
A. Only direct rain on backfill
W
here there is a small width of backfill, it is sufficient that the backfill
be composed of drainage aggregate to permit drainage through the wall.
Where there is a large width of backfill, it must be sealed with a low
permeability layer eg. clay layer, concrete slab etc, to prevent the backfill
becoming saturated.
er
Low p
layer
In this case the surface must be sealed with a low permeability layer to
prevent saturation of the backfill and a surface drain provided to direct
water away in order to prevent scouring.
Lined drain to
direct water away
from wall
adbri masonry
Line of top
Plan on Wall
Windsor
32mm
50mm
Vertica
14mm
Line of top
Hampton Stone
28mm
Meadow Stone
18.75mm
Eden Wall
62mm
Natural Impressions
20mm
Versawall
0mm
Miniwall
0mm
Elevation on Wall
Grade
Windsor
50mm
150mm
Vertica
14mm
Vertica
200mm
25mm
200mm
Hampton Stone
28mm
Hampton Stone
150mm
Meadow Stone
18.75mm
Meadow Stone
150mm
Step up
Step back
Grade
130mm
62mm
Eden Wall
168mm
Natural Impressions
20mm
Natural Impressions
100mm
Versawall
0mm
Versawall
200mm
0mm
Miniwall
125mm
Eden Wall
Miniwall
Step up
Step back
Depth of Embedment
Depth of Embedment
H
10
adbri masonry
e (mm)
H/20
1-18
H/10
18-27
H/7
27-35
H/5
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
1
1.5
No structural loads
within this line
Fence posts may be driven once wall is installed, however they must remain at least
500mm off rear of wall. This applies where aggregate is used as infill material,
or where width of no fines concrete does not encroach on fence location.
Infill depth
b)
ayer
t
If units are
cored through, the no fines
concrete must also completely fill the cored
section of the block.
t
Compacted roadbase
foundation replacement zone
c)
Compacted roadbase
foundation replacement zone
Compacted roadbase
foundation replacement zone
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
11
Parapet
Height (HP)
Railing height
Kerb stop
100mm minimum
Pavement
sub grade
Geogrid Reinforcement
Ensure that Jersey Barrier Design is in accordance with local government specifications
Typical Roadway Barrier
Guardrail height
Column tube or
pvc pipe to be
installed during
wall construction
1m
min.
13mm expansion
joint material
25mm Styrofoam
12
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
Steel reinforcement
Pipe
Pipe
Poured concrete
75mm
minimum
cover
0.30m
minimum
Geogrid reinforcement
Well graded granular
drainage material 12mm
to 20mm with less than
10% fines
Connection of
Retaining Wall Facing
Earth Anchors or Soil Nails
Geogrid
reinforcement
2 blocks
max. spacing
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
13
4.1 VERTICA
Vertica can create near vertical walls without
reinforcement up to 1m high, and is ideal for commercial tall
wall construction. With the use of geogrid reinforcement,
walls can be constructed up to 12m in height.
VERTICA
Minimum
radius = 2.1m
Minimum
radius = 2.1m
200mm
280mm
450mm
305mm
100mm
264mm
455mm
Vertica Cap
Overlap corner
Saw/bolster corner
units as required
for fit
Vertica 11.1
Approx Weight
Setback
1:14 (4)
Bolster here to
expose split face
14
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
Saw and
cutexperienced
as needed
to create
requirements in this document and the directions of suitably qualified
professionals.
The information in this brochure is to be used onlyGlue
with the2specific
Masonry
products shown. Diagrams not to scale.
half Adbri
corner
units
1:4 max
Infill depth
slope
Vertica Cap
Level slope
Low permeability top soil layer
Vertica
No structural loads
within this line
1
1
Infill material*
H Design height
1.5
14
150
150
(natural foundation
material)
600
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
15
Surface Slope
Foundation Material
Infill Material
Type 2
2000
Level
Replacement Zone
NFC
600
800
1800
Level
Replacement Zone
NFC
550
750
1600
Level
Replacement Zone
NFC
450
650
1400
Level
2.5
Replacement Zone
NFC
300
450
1200
Level
2.5
Replacement Zone
NFC
300
350
1000*
Level
2.5
Natural Material
Aggregate
300
300
800*
Level
Natural Material
Aggregate
300
300
600*
Level
Natural Material
Aggregate
300
300
1800
1:4 Maximum
Replacement Zone
NFC
750
1050
1600
1:4 Maximum
Replacement Zone
NFC
650
950
1400
1:4 Maximum
2.5
Replacement Zone
NFC
450
700
1200
1:4 Maximum
2.5
Replacement Zone
NFC
350
550
1000
1:4 Maximum
2.5
Replacement Zone
NFC
300
450
800*
1:4 Maximum
Natural Material
Aggregate
300
300
600*
1:4 Maximum
Natural Material
Aggregate
300
300
Surface Slope
Foundation Material
Infill Material
2000
Level
Replacement Zone
NFC
Type 2
600
800
1800
Level
Replacement Zone
NFC
550
750
1600
Level
Replacement Zone
NFC
450
650
1400
Level
2.5
Replacement Zone
NFC
300
450
1200
Level
2.5
Replacement Zone
NFC
300
350
1000
Level
2.5
Replacement Zone
Aggregate
500
500
1000
Level
2.5
Replacement Zone
NFC
300
300
800
Level
Replacement Zone
Aggregate
400
400
800
Level
Replacement Zone
NFC
300
300
600
Level
Replacement Zone
Aggregate
300
300
1800
1:4 Maximum
Replacement Zone
NFC
750
1050
1600
1:4 Maximum
Replacement Zone
NFC
650
950
1400
1:4 Maximum
2.5
Replacement Zone
NFC
450
700
1200
1:4 Maximum
2.5
Replacement Zone
NFC
350
550
1000
1:4 Maximum
2.5
Replacement Zone
NFC
300
450
800
1:4 Maximum
Replacement Zone
Aggregate
400
400
800
1:4 Maximum
Replacement Zone
NFC
300
300
600
1:4 Maximum
Replacement Zone
Aggregate
300
300
16
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
4.2 LANDMARK
unit
d
ain
bond
180mm
Minimum outside radius
2.75m to face (top course)
380mm
Second Course
Piece B
First Course
320mm
200mm
Piece A
Piece B
Saw cut unit
180mm
190mm
Third Course
200mm
320mm
Piece A
Piece B
1625mm
Fourth Course
Third Course
Pieces A and B
Locking Bar
Landmark Tapered Component Technical Data
No. Per m2 of Wall
13.16
Approx Weight
37kg
Setback
1:14 (4)
Landmark block
front view
Saw cut unit
Saw cut unit
as needed
as needed
to maintain
to maintain
running bond
running bond
Notes
- Remove lower lock flanges from units marked with a (*) and use adhesive to attach
to blocks below.
- Cut units marked with a (X) to maintain running bond, as shown to the right.
Notes
- Remove lower lock
to blocks below.
- Cut units marked w
Notes - Adhere all partial or cut units to adjacent units using an approved construction grade adhesive.
26.32
Approx Weight
23kg
Setback
1:14 (4)
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
17
Piece A
Piece B
Saw cut unit
First Course
Second Course
Pieces A and B
Piece B
Piece A
Piece B
Notes - Adhere all partial or cut units to adjacent units using an approved construction grade adhesive.
Third Course
Fourth Course
Pieces A and B
Saw cut unit
as needed
to maintain
running bond
Infill depth
Landmark cap
slope
Notes
Level slope
- Remove lower lock flanges from units marked with a (*) and use adhesiv
to blocks below.
- Cut units marked with a (X) to maintain running bond, as shown to the ri
Notes - Adhere all partial or cut units to adjacent units using an approved construction grade adhesive.
Landmark
No structural loads
within this line
1
1
H Design height
Infill material*
14
1.5
150
300
130
18
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
Surface Slope
Foundation Material
Infill Material
Type 2
1900
Level
Replacement Zone
NFC
575
750
1710
Level
Replacement Zone
NFC
500
650
1520
Level
Replacement Zone
NFC
425
600
1330
Level
2.5
Replacement Zone
NFC
300
350
1140
Level
2.5
Replacement Zone
NFC
300
300
950*
Level
2.5
Natural Material
Aggregate
300
300
760*
Level
Natural Material
Aggregate
300
300
570*
Level
Natural Material
Aggregate
300
300
1710
1:4 Maximum
Replacement Zone
NFC
725
1000
1520
1:4 Maximum
Replacement Zone
NFC
625
900
1330
1:4 Maximum
2.5
Replacement Zone
NFC
550
600
1140
1:4 Maximum
2.5
Replacement Zone
NFC
325
500
950
1:4 Maximum
2.5
Replacement Zone
NFC
300
400
760*
1:4 Maximum
Natural Material
Aggregate
300
300
570*
1:4 Maximum
Natural Material
Aggregate
300
300
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
19
Surface Slope
Foundation Material
Infill Material
Type 2
1900
Level
Replacement Zone
NFC
575
750
1710
Level
Replacement Zone
NFC
500
650
1520
Level
Replacement Zone
NFC
425
600
1330
Level
2.5
Replacement Zone
NFC
300
350
1140
Level
2.5
Replacement Zone
NFC
300
300
950
Level
2.5
Replacement Zone
Aggregate
500
500
950
Level
2.5
Replacement Zone
NFC
300
300
760
Level
Natural Material
Aggregate
400
400
760
Level
Replacement Zone
NFC
300
300
570
Level
Natural Material
Aggregate
300
300
1710
1:4 Maximum
Replacement Zone
NFC
725
1000
1520
1:4 Maximum
Replacement Zone
NFC
625
900
1330
1:4 Maximum
2.5
Replacement Zone
NFC
550
600
1140
1:4 Maximum
2.5
Replacement Zone
NFC
325
500
950
1:4 Maximum
2.5
Replacement Zone
Aggregate
500
400
950
1:4 Maximum
2.5
Replacement Zone
NFC
300
400
760
1:4 Maximum
Natural Material
Aggregate
400
400
760
1:4 Maximum
Replacement Zone
NFC
300
300
570
1:4 Maximum
Natural Material
Aggregate
300
300
20
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
200mm
DIAMOND PRO
300mm
175mm
Minimum radius
1.8m to face
Minimum radius
1.2m to face
1m
create
Minimum
radius = 2.1m
200mm
1st Course
300mm
275mm
250 unit
Pair Component
Full corner
(see instructions, right,
for creating this unit)
200mm
Overlap corner
300mm
450mm
Full Unit
300mm
2nd Course
100mm
264mm
455mm
Cap
Approx Weight
Setback
1:8 (7.1)
Glue 2 half corner units
together to create a full
corner unit
cut aswalls
needed
create
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on theSaw
site. Retaining
must beto
installed
in accordance with the instructions and
half
unit
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only
withcorner
the specific
Adbri Masonry products shown. Diagrams not to scale.
Glue 2adbri
half corner
units21
masonry
together to create a full
corner unit
Infill depth
pe
Cap Unit
Level slope
Diamond Pro Stone Cut
1
1.5
Infill material*
No structural loads
within this loads
H Design height
150
300
150
(natural foundation
material)
600
22
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
Surface Slope
Foundation Material
Infill Material
Type 2
2200
Level
Replacement Zone
NFC
600
800
2000
Level
Replacement Zone
NFC
550
750
1800
Level
Natural Material
NFC
500
650
1600
Level
Natural Material
NFC
400
600
1400
Level
2.5
Natural Material
NFC
300
300
1200
Level
2.5
Replacement Zone
Aggregate
600
600
1000*
Level
2.5
Natural Material
Aggregate
300
300
800*
Level
2.5
Natural Material
Aggregate
300
300
2000
1:4 Maximum
Replacement Zone
NFC
750
1050
1800
1:4 Maximum
Replacement Zone
NFC
700
950
1600
1:4 Maximum
Replacement Zone
NFC
600
900
1400
1:4 Maximum
2.5
Replacement Zone
NFC
400
650
1200
1:4 Maximum
2.5
Replacement Zone
NFC
300
500
1000*
1:4 Maximum
2.5
Natural Material
Aggregate
500
500
800*
1:4 Maximum
2.5
Natural Material
Aggregate
400
400
Surface Slope
Foundation Material
Infill Material
2000
Level
Replacement Zone
NFC
Type 2
550
750
1800
Level
Replacement Zone
NFC
500
650
1600
Level
Replacement Zone
NFC
400
600
1400
Level
2.5
Replacement Zone
NFC
300
350
1200
Level
2.5
Replacement Zone
NFC
300
300
1000
Level
2.5
Replacement Zone
Aggregate
500
500
800
Level
2.5
Replacement Zone
Aggregate
400
400
1800
1:4 Maximum
Replacement Zone
NFC
700
950
1600
1:4 Maximum
Replacement Zone
NFC
600
900
1400
1:4 Maximum
2.5
Replacement Zone
NFC
400
650
1200
1:4 Maximum
2.5
Replacement Zone
NFC
300
500
1000
1:4 Maximum
2.5
Replacement Zone
Aggregate
500
500
800
1:4 Maximum
2.5
Replacement Zone
Aggregate
400
400
600
1:4 Maximum
2.5
Natural Material
Aggregate
300
300
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
23
Minimum radius
Minimum0.82m
radiusto inside
Minimum
radius
0.82m
to(top
inside
course)
0.82m
to
inside
(top course)
(top course)
150mm
Minimum radius
Minimum0.82m
radiusto face
Minimum
radius
0.82m to(bottom
face
0.82m
to
face course)
(bottom course)
(bottom course)
305mm
395mm
Diamond
150mm
445mm
395mm
Cut Diamond
16.9
Approx Weight
29.3kg
Setback
1:3 (18)
15
Approx Weight
32.3kg
Setback
1:3 (18)
24
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
1:4 max
Infill depth
slope
Level slope
Low permeability top soil layer
Cut Diamond / Diamond
1
Infill material*
1.5
No structural loads
within this line
H Design height
150
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
25
Surface Slope
Foundation Material
Infill Material
Type 2
2850
Level
Replacement Zone
NFC
550
800
2700
Level
Replacement Zone
NFC
500
750
2550
Level
Replacement Zone
NFC
500
750
2400
Level
Replacement Zone
NFC
450
700
2400
Level
Replacement Zone
Aggregate
1200
1200
2100
Level
Replacement Zone
Aggregate
1050
1050
2100
Level
Replacement Zone
NFC
400
600
1800
Level
Replacement Zone
Aggregate
900
900
1800
Level
Replacement Zone
NFC
300
500
1500
Level
2.5
Replacement Zone
Aggregate
750
750
1500
Level
2.5
Replacement Zone
NFC
300
400
1200*
Level
2.5
Natural Material
Aggregate
300
300
2550
1:4 Maximum
Replacement Zone
NFC
700
1050
2400
1:4 Maximum
Replacement Zone
NFC
650
950
2250
1:4 Maximum
Replacement Zone
NFC
600
900
2100
1:4 Maximum
Replacement Zone
NFC
550
850
2100
1:4 Maximum
Replacement Zone
Aggregate
1050
1050
1800
1:4 Maximum
Replacement Zone
Aggregate
900
900
1800
1:4 Maximum
Replacement Zone
NFC
450
750
1500
1:4 Maximum
2.5
Replacement Zone
Aggregate
750
750
1500
1:4 Maximum
2.5
Replacement Zone
NFC
350
600
1200
1:4 Maximum
2.5
Replacement Zone
Aggregate
600
600
26
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
Surface Slope
Foundation Material
Infill Material
2850
Level
Replacement Zone
NFC
Type 2
550
800
2700
Level
Replacement Zone
NFC
500
750
2550
Level
Replacement Zone
NFC
500
750
2400
Level
Replacement Zone
NFC
450
700
2400
Level
Replacement Zone
Aggregate
1200
1200
2100
Level
Replacement Zone
Aggregate
1050
1050
2100
Level
Replacement Zone
NFC
400
600
1800
Level
Replacement Zone
Aggregate
900
900
1800
Level
Replacement Zone
NFC
300
500
1500
Level
2.5
Replacement Zone
Aggregate
750
750
1500
Level
2.5
Replacement Zone
NFC
300
400
1200
Level
2.5
Replacement Zone
Aggregate
600
600
1200
Level
2.5
Replacement Zone
NFC
300
300
900
Level
2.5
Replacement Zone
Aggregate
450
450
900
Level
2.5
Natural Material
NFC
300
300
600
Level
Natural Material
Aggregate
300
300
2550
1:4 Maximum
Replacement Zone
NFC
700
1050
2400
1:4 Maximum
Replacement Zone
NFC
650
950
2250
1:4 Maximum
Replacement Zone
NFC
600
900
2100
1:4 Maximum
Replacement Zone
NFC
550
850
2100
1:4 Maximum
Replacement Zone
Aggregate
1050
1050
1800
1:4 Maximum
Replacement Zone
Aggregate
900
900
1800
1:4 Maximum
Replacement Zone
NFC
450
750
1500
1:4 Maximum
2.5
Replacement Zone
Aggregate
750
750
1500
1:4 Maximum
2.5
Replacement Zone
NFC
350
600
1200
1:4 Maximum
2.5
Replacement Zone
Aggregate
600
600
1200
1:4 Maximum
2.5
Natural Material
NFC
300
350
900
1:4 Maximum
2.5
Natural Material
Aggregate
450
450
900
1:4 Maximum
2.5
Natural Material
NFC
300
300
600
1:4 Maximum
Natural Material
Aggregate
300
300
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
27
4.5 WINDSOR
Minimum radius
0.88m to inside
(top
course)
Minimum
radius
0.88m to inside
(top course)
us
229mm
e)
us
e)
130mm
Minimum radius
0.88m to inside
(top course)
Minimum radius
0.88m to face
(bottom course)
203mm
295mm
Windsor
229mm
130mm
203mm
295mm
Balmoral
ip
ip
26.1
Approx Weight
Setback
1:14 (14)
Remove
Cut rear
unit lip
to fit
Cut unit to fit
Modify units as
needed to maintain
running units
bond as
Modify
needed to maintain
running bond
Split unit as needed to create corner
Cut unit to fit
Split unit as needed to create corner
Modify units as
needed to maintain
running bond
28
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
Split
unit as
needed
corner
requirements in this document and the directions of suitably qualified and experienced professionals. The
information
in this
brochure to
is tocreate
be used only
with the specific Adbri Masonry products shown. Diagrams not to scale.
Infill depth
1:4 max
slope
Level slope
Low permeability top soil layer
Windsor
Infill material*
No structural loads
within this line
1.5
H Design height
e
130
130
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
29
Surface Slope
Foundation Material
Infill Material
1950
Level
Replacement Zone
NFC
Type 2
550
750
1820
Level
Replacement Zone
NFC
500
700
1690
Level
Replacement Zone
NFC
450
650
1560
Level
Replacement Zone
NFC
450
600
1430
Level
2.5
Replacement Zone
NFC
300
400
1300
Level
2.5
Replacement Zone
NFC
350
400
1170
Level
2.5
Replacement Zone
Aggregate
585
585
1170
Level
2.5
Replacement Zone
NFC
300
350
1040*
Level
2.5
Natural Material
Aggregate
300
300
910*
Level
2.5
Natural Material
Aggregate
300
300
780
Level
Natural Material
Aggregate
300
300
650
Level
Natural Material
Aggregate
300
300
1820
1:4 Maximum
Replacement Zone
NFC
650
950
1690
1:4 Maximum
Replacement Zone
NFC
650
900
1560
1:4 Maximum
Replacement Zone
NFC
600
850
1430
1:4 Maximum
2.5
Replacement Zone
NFC
450
650
1300
1:4 Maximum
2.5
Replacement Zone
NFC
400
600
1170
1:4 Maximum
2.5
Replacement Zone
NFC
350
550
1040
1:4 Maximum
2.5
Replacement Zone
Aggregate
520
520
1040
1:4 Maximum
2.5
Replacement Zone
NFC
300
300
780*
1:4 Maximum
Natural Material
Aggregate
300
300
650*
1:4 Maximum
Natural Material
Aggregate
300
300
30
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
Surface Slope
Foundation Material
Infill Material
1950
Level
Replacement Zone
NFC
Type 2
550
750
1820
Level
Replacement Zone
NFC
500
700
1690
Level
Replacement Zone
NFC
450
650
1560
Level
Replacement Zone
NFC
450
600
1430
Level
2.5
Replacement Zone
NFC
300
400
1300
Level
2.5
Replacement Zone
NFC
300
400
1170
Level
2.5
Replacement Zone
Aggregate
585
585
1040
Level
2.5
Replacement Zone
Aggregate
520
520
1040
Level
2.5
Replacement Zone
NFC
300
300
780
Level
Replacement Zone
Aggregate
390
390
780
Level
Replacement Zone
NFC
300
300
520
Level
Natural Material
Aggregate
300
300
1820
1:4 Maximum
Replacement Zone
NFC
650
950
1690
1:4 Maximum
Replacement Zone
NFC
650
900
1560
1:4 Maximum
Replacement Zone
NFC
600
850
1430
1:4 Maximum
2.5
Replacement Zone
NFC
450
650
1300
1:4 Maximum
2.5
Replacement Zone
NFC
400
600
1170
1:4 Maximum
2.5
Replacement Zone
NFC
350
550
780
1:4 Maximum
Replacement Zone
Aggregate
390
390
708
1:4 Maximum
Replacement Zone
NFC
300
350
300
520
1:4 Maximum
Natural Material
Aggregate
300
520
1:4 Maximum
Replacement Zone
NFC
300
300
390
1:4 Maximum
Natural Material
Aggregate
300
300
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
31
Minimum radius
0.6m to inside
150mm
Minimum radius
0.6m to face
HAMPTON
250mm
435mm
Hampton Stone
1st Course
70mm
250mm
450mm
Hampton Stone Cap
15.32
Approx Weight
26kg
Setback
1:5.4 (10.5)
2nd Course
32
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
Minimum radius
0.8m to inside
Infill depth
1:4 max
slope
Capping Unit
Level slope
Low permeability top soil layer
Hampton Stone
1
1.5
5.4
Infill material*
No structural loads
within this line
H Design height
Remove locators
as needed to allow
next course
130
130
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
33
Surface Slope
Foundation Material
Infill Material
1950
Level
Replacement Zone
NFC
Type 2
500
750
1800
Level
Replacement Zone
NFC
500
700
1650
Level
Replacement Zone
NFC
450
650
1500
Level
2.5
Replacement Zone
NFC
400
600
1350
Level
2.5
Replacement Zone
NFC
300
400
1200
Level
2.5
Replacement Zone
NFC
600
600
1200
Level
2.5
Replacement Zone
Aggregate
300
350
1050*
Level
2.5
Natural Material
NFC
300
300
900*
Level
2.5
Natural Material
Aggregate
300
300
750*
Level
Natural Material
Aggregate
300
300
1950
1:4 Maximum
Replacement Zone
NFC
700
1050
1800
1:4 Maximum
Replacement Zone
NFC
650
950
1650
1:4 Maximum
Replacement Zone
NFC
600
900
1500
1:4 Maximum
2.5
Replacement Zone
NFC
550
850
1350
1:4 Maximum
2.5
Replacement Zone
NFC
400
600
1200
1:4 Maximum
2.5
Replacement Zone
NFC
300
550
1050
1:4 Maximum
2.5
Replacement Zone
Aggregate
525
525
900*
1:4 Maximum
2.5
Natural Material
Aggregate
300
300
750*
1:4 Maximum
Natural Material
Aggregate
300
300
34
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
Surface Slope
Foundation Material
Infill Material
1950
Level
Replacement Zone
NFC
Type 2
500
750
1800
Level
Replacement Zone
NFC
500
700
1650
Level
Replacement Zone
NFC
450
650
1500
Level
2.5
Replacement Zone
NFC
400
600
1350
Level
2.5
Replacement Zone
NFC
300
400
1200
Level
2.5
Replacement Zone
Aggregate
600
600
1200
Level
2.5
Replacement Zone
NFC
300
350
1050
Level
2.5
Replacement Zone
Aggregate
525
525
1050
Level
2.5
Replacement Zone
NFC
300
300
900
Level
2.5
Replacement Zone
Aggregate
450
450
900
Level
2.5
Replacement Zone
NFC
300
300
750
Level
Replacement Zone
Aggregate
375
375
750
Level
Replacement Zone
NFC
300
300
600
Level
Natural Material
Aggregate
300
300
450
Level
Natural Material
Aggregate
300
300
1950
1:4 Maximum
Replacement Zone
NFC
700
1050
1800
1:4 Maximum
Replacement Zone
NFC
650
950
1650
1:4 Maximum
Replacement Zone
NFC
600
900
1500
1:4 Maximum
2.5
Replacement Zone
NFC
550
850
1350
1:4 Maximum
2.5
Replacement Zone
NFC
400
600
1200
1:4 Maximum
2.5
Replacement Zone
NFC
300
550
1050
1:4 Maximum
2.5
Replacement Zone
Aggregate
525
525
1050
1:4 Maximum
2.5
Replacement Zone
NFC
300
450
900
1:4 Maximum
2.5
Replacement Zone
Aggregate
450
450
900
1:4 Maximum
2.5
Replacement Zone
NFC
300
350
375
750
1:4 Maximum
Replacement Zone
Aggregate
375
750
1:4 Maximum
Replacement Zone
NFC
300
300
600
1:4 Maximum
Natural Material
Aggregate
300
300
450
1:4 Maximum
Natural Material
Aggregate
300
300
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
35
150mm
150mm
200mm
250mm
1st Course
200mm
400mm
Full Unit
60mm
200mm
300mm
Cap
Approx Weight
Setback
1:8 (7.1)
2nd Course
36
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
Infill depth
1:4 max
slope
Level slope
Low permeability top soil layer
1
1
8
Infill material*
H Design height
1.5
No structural loads
within this line
130
450
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
37
Surface Slope
Foundation Material
Infill Material
Level
Replacement Zone
NFC
600
800
Level
Replacement Zone
NFC
550
750
Type 1
Type 2
1500
Level
2.5
Replacement Zone
NFC
500
700
1350
Level
2.5
Replacement Zone
NFC
350
500
1200
Level
2.5
Replacement Zone
NFC
300
450
1050
Level
2.5
Replacement Zone
NFC
300
400
900
Level
2.5
Replacement Zone
NFC
300
350
750*
Level
Natural Material
Aggregate
300
300
1650
1:4 Maximum
Replacement Zone
NFC
750
1050
1500
1:4 Maximum
Replacement Zone
NFC
700
1000
1350
1:4 Maximum
2.5
Replacement Zone
NFC
500
750
1200
1:4 Maximum
2.5
Replacement Zone
NFC
450
650
1050
1:4 Maximum
2.5
Replacement Zone
NFC
400
600
900
1:4 Maximum
2.5
Replacement Zone
NFC
350
500
750
1:4 Maximum
Replacement Zone
NFC
300
300
600*
1:4 Maximum
Replacement Zone
Aggregate
300
300
Surface Slope
Foundation Material
Infill Material
Type 2
1800
Level
Replacement Zone
NFC
600
800
1650
Level
Replacement Zone
NFC
550
750
1500
Level
2.5
Replacement Zone
NFC
500
700
1350
Level
2.5
Replacement Zone
NFC
350
500
1200
Level
2.5
Replacement Zone
NFC
300
450
1050
Level
2.5
Replacement Zone
NFC
300
400
900
Level
2.5
Replacement Zone
Aggregate
450
350
900
Level
2.5
Replacement Zone
NFC
300
300
750
Level
Replacement Zone
Aggregate
375
375
750
Level
Replacement Zone
NFC
300
300
600
Level
Natural Material
Aggregate
300
300
1650
1:4 Maximum
Replacement Zone
NFC
750
1050
1500
1:4 Maximum
Replacement Zone
NFC
700
1000
1350
1:4 Maximum
2.5
Replacement Zone
NFC
500
750
1200
1:4 Maximum
2.5
Replacement Zone
NFC
450
650
1050
1:4 Maximum
2.5
Replacement Zone
NFC
400
600
900
1:4 Maximum
2.5
Replacement Zone
NFC
350
500
750
1:4 Maximum
Replacement Zone
NFC
300
300
600
1:4 Maximum
Replacement Zone
Aggregate
300
300
38
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
45
mm
0m
34
720mm
30
190mm
168mm
First Course
340m
Second Course
1226mm
Eden Wall
60
1226mm
340m
190mm
390mm
4 - 6 co
340
60
720mm
340
340m
m
mm
34
0m
First Course
13kg
n
ce
30
340
First Course
mm
340
340m
1226mm
22m
0m
m
First Course
1226mm
Second Course
200mm
el
ntr
ce 45
22m
Second Course
22m
e
720mm
lin
tre
n
ce 45
200mm
Second Course
Second Course
30
ine
el
ntr
ce 45
200mm
30
60
tre
n
ce
lin
200mm
30
60
re
nt
ce
lin
300mm
m
300m
200mm
50mm
50m
200mm
Second Course
200mm
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
e
requirements in this document and the directions of suitably qualified
lin and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
22m
ce
e
ntr
200mm
ine
adbri masonry
39
re
nt
ce
60
200mm
ine
First Course
mm
340
200mm
First Course
First Course
200mm 45
30
lin
Second Course
tre
n
ce
60
720mm
720mm
34
200mm
720mm
0m
34
- 645
course high wall
mm
mm
30
340
e
lin
tre 4
45
22m
340
200mm
Se
720mm
mm
mm
340
45
1226mm
1226mm
0m
34
720mm
200mm
340m
m
340m
1:2.75 (20)
200mm
Fir
Second Course
1226mm
7 - 8 course
high wall 60
60
30
m
340m
200mm
Approx Weight
Setback
30
lin
Infill depth
1:4 max
slope
Level slope
Eden
1
1
Infill material
2.75
1.5
H Design height
No structural loads
within this line
e
20MPa Concrete levelling pad
130
300
130
40
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
Surface Slope
Foundation Material
Infill Material
1350
Level
2.5
Replacement Zone
Aggregate
1180
Level
2.5
Replacement Zone
Aggregate
590
590
1010*
Level
2.5
Natural Material
Aggregate
300
300
840*
Level
2.5
Natural Material
Aggregate
300
300
670*
Level
Natural Material
Aggregate
300
300
Type 2
675
675
510*
Level
Natural Material
Aggregate
300
300
340*
Level
Natural Material
Aggregate
300
300
1180
1:4 Maximum
2.5
Replacement Zone
Aggregate
590
590
1010
1:4 Maximum
2.5
Replacement Zone
Aggregate
505
505
840*
1:4 Maximum
2.5
Natural Material
Aggregate
300
300
670*
1:4 Maximum
Natural Material
Aggregate
300
300
510*
1:4 Maximum
Natural Material
Aggregate
300
300
340*
1:4 Maximum
Natural Material
Aggregate
300
300
Surface Slope
Foundation Material
Infill Material
1350
Level
2.5
Replacement Zone
Aggregate
Type 2
675
675
1180
Level
2.5
Replacement Zone
Aggregate
590
590
1010
Level
2.5
Replacement Zone
Aggregate
505
505
840
Level
2.5
Natural Material
Aggregate
420
420
670
Level
Natural Material
Aggregate
335
335
510
Level
Natural Material
Aggregate
300
300
340
Level
Natural Material
Aggregate
300
300
1180
1:4 Maximum
2.5
Replacement Zone
Aggregate
590
590
1010
1:4 Maximum
2.5
Replacement Zone
Aggregate
505
505
840
1:4 Maximum
2.5
Natural Material
Aggregate
420
420
670
1:4 Maximum
Natural Material
Aggregate
335
335
510
1:4 Maximum
Natural Material
Aggregate
300
300
340
1:4 Maximum
Natural Material
Aggregate
300
300
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
41
as needed
orner
as needed
orner
100mm
175mm
300mm
Natural Impressions
50mm
200mm
300mm
Natural Impressions Cap
NATURAL
IMPRESSIONS
Full corner unit
(see below for instructions
for creating this unit)
1st Course
33.33
Approx Weight
9.42kg
Setback
1:5 (11.3)
Large Mitre
3.33
Approx Weight
5.94
Setback
1:5 (11.3)
2nd Course
1st and 2nd course details to be installed
alternately for the full height of the wall.
Due to the setback of each course, it may
be necessary to trim adjacent units to
restore bond.
All partial units shall be glued to ALL adjacent
units using a suitable construction adhesive
Saw cut as needed to create
half corner unit
nit as needed
in running bond
Small Mitre
42
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
1:4 max
Flagstone Cap
Flagstone
slope
Level slope
Low permeability top soil layer
Infill material*
Maximum Height
800mm (8 courses)
*Refer to page 11
when using No Fines
concrete infill material
100mm diameter
sub soil drain
150
300
Compacted
road base
150
450
To achieve the Natural Impressions look, the product should be laid randomly throughout the entire wall ie working down
the sides of the pallet rather than across
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
43
Surface Slope
Foundation Material
Infill Material
1500
Level
Replacement Zone
NFC
Type 2
450
650
1400
Level
2.5
Replacement Zone
NFC
350
500
1300
Level
2.5
Replacement Zone
NFC
300
450
1200
Level
2.5
Replacement Zone
NFC
300
400
1100
Level
2.5
Replacement Zone
NFC
300
350
1000
Level
2.5
Replacement Zone
NFC
300
300
900
Level
2.5
Replacement Zone
Aggregate
450
450
800
Level
Natural Material
Aggregate
300
300
1400
1:4 Maximum
2.5
Replacement Zone
NFC
600
700
1300
1:4 Maximum
2.5
Replacement Zone
NFC
500
650
1200
1:4 Maximum
2.5
Replacement Zone
NFC
400
600
1100
1:4 Maximum
2.5
Replacement Zone
NFC
350
550
1000
1:4 Maximum
2.5
Replacement Zone
NFC
300
500
900
1:4 Maximum
2.5
Replacement Zone
NFC
300
450
800
1:4 Maximum
Replacement Zone
NFC
300
400
700
1:4 Maximum
Replacement Zone
Aggregate
350
350
600
1:4 Maximum
Natural Material
Aggregate
300
300
500
1:4 Maximum
Natural Material
Aggregate
300
300
44
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
VERSAWALL
4.10 VERSAWALL
Versawall can create totally vertical walls without
reinforcement up to 800mm in height. The wall units can
also be used with no fines concrete infill material to achieve
greater heights.
VERSAWALL
FACE
FACE
200mm
220mm
400mm
1st Course
Versawall CornersEnd
Detail
units to be adhered together and
core filled with no fines concrete
Versawall
1st Course
200mm
220mm
400mm
Versawall Corner
2nd Course
60mm
2nd Course
240mm
300mm
Versawall Cap
12.5
Approx Weight
21.3kg
3.33
Setback
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
45
Infill depth
see table
Capping unit
Level slope
Low permeability top soil layer
Versawall units
No structural loads
within this line
1
Height varies
Infill Material
1.5
150
150
600
46
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
Surface Slope
Foundation Material
Infill Material
1400
Level
2.5
Replacement Zone
NFC
Type 2
450
550
1200
Level
2.5
Replacement Zone
NFC
350
500
1000
Level
2.5
Replacement Zone
NFC
300
400
800**
Level
Natural Material
Aggregate
300
300
600**
Level
Natural Material
Aggregate
300
300
1400
1:4 Maximum
2.5
Replacement Zone
NFC
550
800
1200
1:4 Maximum
2.5
Replacement Zone
NFC
500
700
1000
1:4 Maximum
2.5
Replacement Zone
NFC
350
550
800
1:4 Maximum
2.5
Replacement Zone
NFC
300
450
600
1:4 Maximum
2.5
Replacement Zone
NFC
300
300
Foundation Material
Infill Material
Surface Slope
Type 2
1400
Level
2.5
Replacement Zone
NFC
450
550
1200
Level
2.5
Replacement Zone
NFC
350
500
1000
Level
2.5
Replacement Zone
NFC
300
400
800
Level
2.5
Replacement Zone
NFC
300
300
600
Level
2.5
Natural Material
Aggregate
300
300
1400
1:4 Maximum
2.5
Replacement Zone
NFC
550
800
1200
1:4 Maximum
2.5
Replacement Zone
NFC
500
700
1000
1:4 Maximum
2.5
Replacement Zone
NFC
350
550
800
1:4 Maximum
2.5
Replacement Zone
NFC
300
450
600
1:4 Maximum
2.5
Replacement Zone
NFC
300
300
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
47
4.10 VERSASTONE
VERSAstone
Versastone
Stop End Detail
VERSAstone
200mm
FACE
Cut Versastone corner unit
on alternating courses to
FACE
maintain stretcher bond
400mm
190mm
Versastone
1st Course
1st Course
200mm
390mm
190mm
Versastone Corner
2nd Course
390mm
190mm
Versastone Cap
12.5
2nd Course
1st and 2nd course details to be installed alternatively
for the full height of the wall.
1st and 2nd course details to be installed alternatively
All partial units shall befor
glued
to ALL
adjacent
the full
height
of the units
wall.
using a suitable construction adhesive
All partial units shall be glued to ALL adjacent units
using a suitable construction adhesive
15.27kg
2.5
Setback
48
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
Infill depth
see table
Capping unit
Level slope
Low permeability top soil layer
Versastone units
No structural loads
within this line
1
Height varies
Infill Material
1.5
150
150
600
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
49
Surface Slope
Foundation Material
Infill Material
1400
Level
2.5
Replacement Zone
NFC
Type 2
475
575
1200
Level
2.5
Replacement Zone
NFC
375
525
1000
Level
2.5
Replacement Zone
NFC
325
425
800**
Level
2.5
Replacement Zone
NFC
300
325
600**
Level
Natural Material
Aggregate
300
300
1400
1:4 Maximum
2.5
Replacement Zone
NFC
575
825
1200
1:4 Maximum
2.5
Replacement Zone
NFC
525
725
1000
1:4 Maximum
2.5
Replacement Zone
NFC
375
575
800
1:4 Maximum
2.5
Replacement Zone
NFC
325
475
600
1:4 Maximum
2.5
Replacement Zone
NFC
300
325
Foundation Material
Infill Material
Surface Slope
Type 2
1400
Level
2.5
Replacement Zone
NFC
450
550
1200
Level
2.5
Replacement Zone
NFC
350
500
1000
Level
2.5
Replacement Zone
NFC
300
400
800
Level
2.5
Replacement Zone
NFC
300
300
600
Level
2.5
Natural Material
Aggregate
300
300
1400
1:4 Maximum
2.5
Replacement Zone
NFC
550
800
1200
1:4 Maximum
2.5
Replacement Zone
NFC
500
700
1000
1:4 Maximum
2.5
Replacement Zone
NFC
350
550
800
1:4 Maximum
2.5
Replacement Zone
NFC
300
450
600
1:4 Maximum
2.5
Replacement Zone
NFC
300
300
50
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
4.12 MINIWALL
182mm
182mm
Miniwall
132mm
125mm
182mm
182mm
Minicap
Approx Weight
4.4kg
Setback
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
51
1:4 max
slope
Level slope
Low permeability top soil layer
Miniwall
Infill material*
Maximum Height
800mm (8 courses)
*Refer to page 11
when using No Fines
concrete infill material
100mm diameter
sub soil drain
150
300
Compacted
road base
150
450
52
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
Surface Slope
Foundation Material
Infill Material
Type 1
Type 2
875
Level
2.5
Replacement Zone
NFC
300
400
750
Level
Replacement Zone
NFC
300
300
625
Level
Replacement Zone
NFC
300
300
500**
Level
Natural Material
Aggregate
300
300
375**
Level
Natural Material
Aggregate
300
300
875
1:4 Maximum
2.5
Replacement Zone
NFC
400
650
750
1:4 Maximum
Replacement Zone
NFC
300
550
625
1:4 Maximum
Replacement Zone
NFC
300
350
500
1:4 Maximum
Replacement Zone
NFC
300
300
375
1:4 Maximum
Replacement Zone
NFC
300
300
Foundation Material
Infill Material
Surface Slope
875
Level
2.5
Replacement Zone
750
Level
Replacement Zone
625
Level
500
Level
375
Level
875
1:4 Maximum
750
1:4 Maximum
625
Type 2
NFC
300
400
NFC
300
300
Replacement Zone
NFC
300
300
Replacement Zone
NFC
300
300
Replacement Zone
NFC
300
300
2.5
Replacement Zone
NFC
400
650
Replacement Zone
NFC
300
550
1:4 Maximum
Replacement Zone
NFC
300
350
500
1:4 Maximum
Replacement Zone
NFC
300
300
375
1:4 Maximum
Replacement Zone
NFC
300
300
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
53
Install
retaining
units large format of choice
Install
Adbriwall
Masonry
withpaver
required
withdistance
bullnosebetween
to create stair tread
Installdesired
retaining
units
to create
stepwall
width
with required distance between
to create desired step width
Install retaining wall units
with required distance between
to create desired step width
2R + G
Maximum
Minimum
Maximum
Minimum
Maximum
Minimum
190
115
355
250
700
550
NOTE - Adbri designs are for step tread dimensions and layout only, and do not consider handrail or landing platform requirements. Consult relevant Australian Standards.
54
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
Reinforced soil retaining walls are essentially gravity wall structures that depend
on the mass of the reinforced soil zone behind the retaining wall units to resist
destabilising forces due to retained soil and surcharge loadings.
not require the use of additional dowels to provide block shear capacity. Landmark,
Diamond, Hampton Stone or Vertica blocks, due to their unique construction, are
extremely quick and easy to lay. They come in a variety of face finishes and a wide
array of colour options to complement existing surroundings. Special colours can be
formulated to match into existing works or create that special effect.
The combination of retaining wall blocks with Geogrid has been accepted by major
construction authorities in Australia for use in structures with a design life of 100 years.
Geogrid provides connection of the reinforced soil to the Adbri Masonry segmental
retaining wall blocks. The combination of retaining wall blocks with Geogrid has the
capacity to form a mechanical connection.
Geogrid was chosen as the preferred reinforcing element because of its light, flexible
nature, ease of handling, superior creep resistance and long term load carrying
capacity compared to other products on the market, and its maintained strength/
creep characteristics when subjected to elevated surface temperatures commonly
experienced in block retaining system applications.
Retaining wall design software is available free of charge to engineers to allow the
optimum use of Geogrid and retaining wall products. We can also provide contracting
services for all types of retaining wall projects.
Landmark, Vertica and Diamond are all R57 and MRS11.06 approved products.
For a copy of the Anchor wall Program go to adbrimasonry.com.au and send a request
to the company. The program is AutoCAD compatible.
Surcharge
Setback varies
Excavation
Granular fill
Other grid layers
H
Geo synthetic grid
Retained soil
2nd grid layer
Foundation material
150mm min. granular fill or concrete levelling pad
as detailed for each block type
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
adbri masonry
55
Landmark offers an innovative solution for retaining wall construction. The unique
system features a positive mechanical connection between the facing blocks and the
reinforcement material that bolsters the walls ability to withstand the forces of earth
pressures, surcharges and seismic loads as it retains the surrounding soil.
How does the uniquely shaped Landmark system fasten to the reinforcement
materials? A lock bar made from an engineered polymer, fits into a specially designed
channel built into the blocks. This locking system mechanically and positively connects
the block to a layer of reinforcing material. Uniquely shaped flanges establish a
uniform course-to-course set back and ensure a strong resistance to shear forces.
Never before has a segmental retaining wall system demonstrated this level
of strength with polyester reinforcements. The Landmark system was designed
specifically for challenging projects such as tall walls over 4.5m, high load-bearing
walls of any height, transportation applications and structures located in seismic
regions. The performance features of the Landmark system enable cost effective
design solutions
56
adbri masonry
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and
requirements in this document and the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. Diagrams not to scale.
Contact Us
adbrimasonry.com.au
1300 365 565
enquiries@adbri.com.au
Designer Paving
Industrial Masonry
masonrytech@adbri.com.au
We will not accept any returns or claims more than 7 days after delivery or after products have been installed. We will not accept returns unless transport arrangements have been
agreed and the products are in as received condition and accessible for collection. We will only accept returns as follows:
Paving and Retaining Walls - returns accepted only in full pallets stacked in original configuration.
No returns accepted for any made to order product.
Free pallet collection service freecall 1800 674 961 or drop pallets back to place of purchase or lodge your pallet pick up online
at adbrimasonry.com.au
Pallets remain Adbri Masonry property. Please telephone us for collection of pallets and keep pallets empty and stacked in a safe and accessible area for collection.
For all technical enquiries please email masonrytech@adbri.com.au and speak directly with our in-house Technical and Engineering Teams.
All specifications and assumed properties in this document (including those in Section 1.0 Technical Parameters) must be present and achieved on the site. Retaining walls must be installed in accordance with the instructions and requirements in
this document (including design and cross sectional details) the directions of suitably qualified and experienced professionals. The information in this brochure is to be used only with the specific Adbri Masonry products shown. All images, designs,
drawings and other depictions of the installation and/or use of products in this document are examples only, and should not be relied on. To the maximum extent permitted by law, in no circumstances will Adbri Masonry be liable to any party
for any direct, indirect, consequential, incidental, special or economic loss, damage or injury (which may include loss of profits, loss or damage to goodwill, direct or indirect loss or damage to equipment or property, loss or damage arising from
accident, loss of profits or other commercial losses) suffered or incurred by that party.
Adbri Masonry makes no express warranties or representations regarding the products, designs or information set out in this document, and to the maximum extent permitted by law, excludes all representations, warranties, terms, conditions and
guarantees regarding the products and designs and information set out in this document, and any other goods or services supplied or provided by Adbri Masonry to the customer that are implied by law (including the general law) or custom. While
Adbri Masonry does not exclude, restrict or modify any guarantees, warranties and conditions implied by applicable laws that cannot lawfully be excluded, restricted or modified, including but not limited to those set out in the Australian Consumer
Law, to the maximum extent permitted by law Adbri Masonrys liability to any party for a breach of any such applicable non-excludable terms is limited to, at the option of Adbri Masonry: (a) in the case of goods - replacement of the goods, the
supply of equivalent goods, repair of the goods, payment of the cost of replacing the goods or acquiring equivalent goods, or payment of the costs of having the goods repaired; and (b) in the case of services - the supply of the services again or
payment of the cost of having the services supplied again.