Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
B F 1~5 ~ ~ 1 3 Paper
0 ~ book Part no. 66ZW500
PREFACE
This manual covers t h e construction, function and
servicing procedures of the Honda BFI 15A / BF130A
outboard motors.
CONTENTS
SPECIFICATIONS
SERVICE INFORMATION
MAINTENANCE
ENGINE COVERITIMING BELT UPPER
COVER
PROGRAMMED FUEL INJECTION (PGM-FI)
ALTERNATORIBALANCER BELT /TIMING
BELT
ENGINE REMOVALIINSTALLATION
WATER JACKET COVERfTHERMOSTATI
PRESSURE VALVE
CYLINDER HEADIVALVES
FLYWHEELIOIL PUMP
BALANCER SHAFT/CRANKCASE/
CRANKSHAFTIPISTON
PROPELLERIGEAR CASEIEXTENSION
CASE
OIL PANIENGINE UNDERCASE/MOUNTING
CASE
SWIVEL CASEIPOWER TRIMITILT
ASSEMBLY
http://www.ReadManuals.Com
HONDA
BFI 15A-130A
16 x 49 mm BOLT-WASHER
111
16 x 49 mrn
BOLT-WASHER
REMOVAL:
NOTE:
Do not use an impact wrench.
Remove the 16 x 49 m m bolt-washer while holding the
crankshaft pulley with the special tool. Do not turn the
crankshaft counterclockwise.
TOOLS:
Holder attachment, 50 mm, offset
Holder handle
07MAB-PY30100
07JAB-001020B
INSTALLATION:
[21
TORQUE
NOTE:
Do not use an impact wrench.
Tighten the 16 x 49 mm bolt-washer while holding thecrankshaft pulley with the special toot. Do not turn the crankshaft
pulley counterclockwise.
YRENcH
[I]
HOLDER ATTACHMENT,
50 mm, OFFSET
07MAB-PY30100
HOLDER HANDLE
07JAB-001020B
07MAB-PY30100
07JAB-001020B
16 x 49 m m
BOLT-WASHER
1
90A FUSE CABLE
INSTALLATION:
1) Connect the 90A fuse cable to the alternator terminal with
the caulked part toward you.
111
90A FUSE CABLE
\
I ^
[31 ALTERNATOR
TERMINAL
[21
6 m m HEX. NUT
COVER s:
6-3
Page: 168 - Honda BF115A, BF130A Outboard Motors Shop Manual -
http://www.ReadManuals.Com
~1
FUSE
CCABLE
go^
HONDA
BFI1 5A-130A
8) Apply soapy water to the lip (shaded part) of the spark plug
tube seal as shown.
9) Clean the cylinder head mating surfaces with a shop towel
or equivalent material. Align the spark plug tube and the
spark plug tube seal by inserting the return tube into the
hole in the mounting case, and install the cylinder head cover.
Insert the spark plug tube into the spark plug tube seal
with care not to cut or turn up the seal.
After installing the cylinder head cover, visually check the
seal for turn-up or damage.
Wipe up the excessive soapy water that oozed out from
the lip of the spark plug tube.
131
/
/
Apply soapy water to
the shaded part.
9-6
Page: 200 - Honda BF115A, BF130A Outboard Motors Shop Manual -
http://www.ReadManuals.Com
This manual covers the construction, function and servicing procedures of the Honda
BF115A, BF130A Outboard Motors.
All information contained in this manual is based on the latest product information
available.
CONTENTS:
SPECIFICATIONS
SERVICE INFORMATION
MAINTENANCE
PROPELLER GEAR CASE/EXTENSION CASE
ENGINE COVERS
FUEL SYSTEM
RECOIL STARTER
ENGINE REMOVAL/INSTALLATION
FLYWHEEL TIMING BELT
CYLINDER HEAD HEAD/VALVES/OIL PUMP
CRANKCASE/ CRANKSHAFT/PISTON
OIL CASE/STERN BRACKET/SWIVEL CASE
SHIFT MECHANISM
STEERING RODIREMOTE CONTROL BOX
TILLER HANDLE
ELECTRICAL EQUIPMENT
WIRING DIAGRAMS
Also included in this manual:
BF115A, BF130A Setup procedures
Honda BF models information and specification information
Searches for
outboard engine wiring color codes, bf115a outboard oil filter,
Honda outboard BF115A BF130A shop, official Honda BF115A
130a marine outboard shop manual - 61zw500, honda bf130 fuel
pump, honda bf 130 hp repair manual, yamaha 130 outboard
wiring diagram, honda outboard bf 130A, Honda outboard 2002
BF130 BF115 a owner manual, honda 130 service manual,