Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
ROOF
DESCRIPTION
RECOMMENDED USE
Colors
Finish
Viscosity
Specific Gravity
Solid by Weight %
Theoretical Spreading Rate
Film Thickness
Elongation - DIN 53455
Water Resistance
Water Vapour Permebility
U. V. Resistance
Reinforcement
Drying Time
Application Methods
Thinning / Cleaning of Tools
RECOMMENDED SYSTEM
Primer Coat: 1 coat National Roof diluted (1 : 1) with water.
Intermediate coat: 1 coat National Roof diluted (2 : 1) with water.
Fix National Fiber Glass mesh while the intermediate is wet, allow to dry.
Top Coat: 1 - 2 coats National Roof undiluted.
OR
Without fibre mesh directly apply over dry intermediate coat 2 coats undiluted National Roof.
SURFACE PREPARATION
Must be clean, dry and free from dust, sand, other contaminations. Local touch -up of larger blow holes /
cracks should be carried out prior to the application of the first full coat of National Roof.
1/2
ROOF
MISCELLANEOUS DATA
STORAGE
HANDLING
SHELF LIFE
SAFETY / HEALTH
NOTE:
We warranty the quality of our product and this data sheet represents test results and practical experience
obtained under controlled conditions. We reserve the right to change data without prior notice.
2/2
RECOMMENDED USE
Flash Point
TECHNICAL INFORMATION
Clear, Transparent.
Matt.
2.5 - 3.5 Poise.
0.78 0.02
5 0.2%
3 - 5 m/Lit.
Touch dry : 1 hr.
Recoatable: 2 - 4 hrs.
38C
Application Methods
Thinning / Cleaning of Tools
APPLICATION DATA
Brush, Roller or Spray.
White Spirits.
Colors
Finish
Viscosity
Specific Gravity
Solid by Weight %
Theoretical Spreading Rate
Drying time
SURFACE PREPARATION
The stone walls should be throughly clean from dust and dirt.
MECHANICIAL
Reacts with atmospheric moisture or pore water in the substrate, thereby generating the active ingredient and
liberating alcohol, the active ingredient greatly lowers absorbency of the substrate. Since neither pores nor
capillaries are clogged, the substrate retains a very high degree of water vapor permeability.
STORAGE
HANDLING
SHELF LIFE
SAFETY / HEALTH
NOTE:
MISCELLANEOUS DATA
The product must be stored according to National Regulations. The
product should be kept in cool and well ventilated place, protected from
heat and direct sunlight at temp 5-35C. Containers must be kept tightly
closed.
Handle with care, mix well before use.
6 months.
- Ensure good ventilation during application and drying.
- Avoid contact with skin and eyes. While painting it is advisable to
wear eye protector. In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice. To remove splashes
from skin; use soap and water or a recognized skin cleaner.
Keep out of reach of children.
We warranty the quality of our product and this data sheet represents test results and practical experience
obtained under controlled conditions. We reserve the right to change data without prior notice.
RECOMMENDED USE
Colors
Viscosity
Specific Gravity
Solid by Weight %
Drying Time
TECHNICAL INFORMATION
White, Bronze.
Thick paste.
1.56 0.05
75 2%
Touch dry: 30 min.
Hard dry : 24 hrs.
NOTE:
It must not be used for splits wider than 1cm before treatment.
Application Methods
Cleaning of Tools
APPLICATION DATA
Special Gun.
Water
SURFACE PREPARATION
Surface to be sealed should be sound dry, free of oils, dust mortar spatter, release agents, old caulks,
intermediate old paint or other contaminants.
STORAGE
HANDLING
SHELF LIFE
SAFETY / HEALTH
NOTE:
MISCELLANEOUS DATA
The product must be stored according to National Regulations. The
product should be kept in cool and well ventilated place, protected from
heat and direct sunlight at temp 5-35C. Containers must be kept tightly
closed.
Handle with care, mix well before use.
18 months.
- Ensure good ventilation during application and drying.
- Avoid contact with skin and eyes. While painting it is advisable to
wear eye protector. In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice. To remove splashes
from skin; use soap and water or a recognized skin cleaner.
- Keep out of reach of children.
We warranty the quality of our product and this data sheet represents test results and practical experience
obtained under controlled conditions. We reserve the right to change data without prior notice.
RECOMMENDED USE
Colors
Specific Gravity
Solid by Weight %
Drying Time
TECHNICAL INFORMATION
White
1.68 2%
70 2%
Touch dry : 2 hrs.
Recoatable: 6 hrs.
NOTE:
Application Methods
Cleaning of Tools
APPLICATION DATA
Special Gun.
Water
SURFACE PREPARATION
Surface to be sealed should be sound dry, free of oils, dust mortar spatter, release agents, old caulk,
intermediate old paint or other contaminants.
STORAGE
HANDLING
SHELF LIFE
SAFETY / HEALTH
NOTE:
MISCELLANEOUS DATA
The product must be stored according to National Regulations. The
product should be kept in cool and well ventilated place, protected from
heat and direct sunlight at temp 5-35C. Containers must be kept tightly
closed.
Handle with care, mix well before use.
18 months.
- Ensure good ventilation during application and drying.
- Avoid contact with skin and eyes. While painting it is advisable to
wear eye protector. In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice. To remove splashes
from skin; use soap and water or a recognized skin cleaner.
- Keep out of reach of children.
We warranty the quality of our product and this data sheet represents test results and practical experience
obtained under controlled conditions. We reserve the right to change data without prior notice.
SWIMMING POOL
DESCRIPTION
RECOMMENDED USE
Flash point
TECHNICAL INFORMATION
White, Blue.
Smooth & Matt.
14 - 16 Poise.
1.44 0.05
70 5%
5 - 6 m2/Lit.
Touch dry: 15 - 20 min.
Hard dry : 2 - 4 hrs.
35C
NOTE:
Application Methods
Thinning / Cleaning of Tools
Film Thickness
Guiding Data for Airless Spray
APPLICATION DATA
Brush, Spray, Roller.
Ready for use, could be diluted with Synthetic Thinner.
(D.F.T.) 100 microns.
Nozzle Tip: 0.015" - 0.20"
Nozzle Pressure: 2200 P.S.I
Colures
Finish
Viscosity (25C)
Specific Gravity
Solid by Weight %
Theoretical Spreading Rate
Drying time
SURFACE PREPARATION
Surface must be clean, dry and free from oil grease, dirt etc...
STORAGE
HANDLING
SHELF LIFE
SAFETY / HEALTH
NOTE:
MISCELLANEOUS DATA
The product must be stored according to National Regulations. The
product should be kept in cool and well ventilated place, protected from
heat and direct sunlight at temp 5-35C. Containers must be kept tightly
closed.
Handle with care, mix well before use.
18 month.
- Ensure good ventilation during application and drying.
- Avoid contact with skin and eyes. While painting it is advisable to
wear eye protector. In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice. To remove splashes
from skin; use soap and water or a recognized skin cleaner.
- Keep out of reach of children.
We warranty the quality of our product and this data sheet represents test results and practical experience
obtained under controlled conditions. We reserve the right to change data without prior notice.
INTUMESCENT PAINT
DESCRIPTION
RECOMMENDED USE
Colors
Finish
Solid by Volume %
Theoretical Spreading Rate
Specific Gravity
Drying Time
Fire Resistance
Flash Point
Application Methods
Thinning (Max. Vol.)
Film Thickness
Guiding Data for Airless Spray
TECHNICAL INFORMATION
White
Matt or Silky
60 2%
3 m2/Lit. per coat.
1.20 0.05
Touch Dry: 2 hrs.
Recoat Interval: 24 hrs.
Hard Dry: 48 hrs.
Temperature, humidity, air movment, film thickness and number of coats
all affect the drying time.
Direct : 600C: 30 min.
Indirect : 600C: 2 hrs.
29C
APPLICATION DATA
Brush, Roller or Spray.
5 - 10% by National Thinner No.110
(D.F.T.) 200 microns.
(W.F.T.) 380 microns.
Nozzle Orifice: 0.0017"
Nozzle Pressure: 2200 P.S.I.
Atomizing Pressure: 50 P.S.I.
SURFACE PREPARATION
Surface should be thoroughly cleaned, dry and primed.
1)
Apply first thin coat.
2)
Apply second coat.
3)
Apply third coat for better fire retardant properties.
1/2
INTUMESCENT PAINT
MISCELLANEOUS DATA
STORAGE
HANDLING
SHELF LIFE
SAFETY / HEALTH
NOTE:
We warranty the quality of our product and this data sheet represents test results and practical experience
obtained under controlled conditions. We reserve the right to change data without prior notice.
2/2
RECOMMENDED USE
Colors
Finish
Solid by Volume %
Theoretical Spreading Rate
Specific Gravity
Drying Time:
Fire Resistance
Flash Point
Application Methods
Thinning (Max. Vol.)
Film Thickness
Guiding Data for Airless Spray
TECHNICAL INFORMATION
White
Matt
55% 2
2.5 m2/Lit.
1.25 0.05
Touch Dry: 1 - 2 hrs.
Recoat Interval: 10 - 12 hrs.
Hard Dry: 24 hrs.
Temperature, humidity, air movment, film thickness and number of coats
all affect the drying time.
Direct : 400C : 30 min.
Indirect : 400C : 2 hrs.
29C
APPLICATION DATA
Brush, Roller or Spray.
5 - 10% by National Fire Retardant Thinner.
(D.F.T.) 100 microns.
(W.F.T.) 180 microns.
Nozzle Orifice: 0.0017"
Nozzle Pressure: 2200 P.S.I.
Atomizing Pressure: 50 P.S.I.
SURFACE PREPARATION
Surface should be thoroughly cleaned, dry.
1)
Apply first thin coat.
2)
Apply second coat.
3)
Apply third coat for better fire retardant properties.
1/2
HANDLING
SHELF LIFE
SAFETY / HEALTH
NOTE:
We warranty the quality of our product and this data sheet represents test results and practical experience
obtained under controlled conditions. We reserve the right to change data without prior notice.
2/2
RECOMMENDED USE
Colors
Finish
Solid by Volume %
Theoretical Spreading Rate
Specific Gravity
Drying Time
Fire Resistance
Flash Point
Application Methods
Thinning (Max. Vol.)
Film Thickness
Guiding Data for Airless Spray
SURFACE PREPARATION
Surface should be thoroughly cleaned, dry.
(1) Apply first thin coat National Fire Retardant Paint
: 2 - 3 coats
(2) Apply second coat National Fire Retardant Clear
: 1 coat
OR
(3) Apply National Fire Retardant Clear
: 3 coats
1/2
HANDLING
SHELF LIFE
SAFETY / HEALTH
NOTE:
We warranty the quality of our product and this data sheet represents test results and practical experience
obtained under controlled conditions. We reserve the right to change data without prior notice.
2/2
RECOMMENDED USE
Appearance
Transparent Liquid.
Specific Gravity @ 15 C
0.77 - 0.79
Viscosity by Fordcup B4
12 - 14 Seconds.
Odour
Mild
Flash Point
41C
1.432
150 - 197C
STORAGE
HANDLING
SHELF LIFE
SAFETY / HEALTH
NOTE:
MISCELLANEOUS DATA
The product must be stored according to National Regulations. The
product should be kept in cool and well ventilated place, protected from
heat and direct sunlight at temp 5-35C. Containers must be kept tightly
closed.
Handle with care, mix well before use.
24 months.
- Ensure good ventilation during application and drying.
- Avoid contact with skin and eyes. While painting it is advisable to
wear eye protector. In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice. To remove splashes
from skin; use soap and water or a recognized skin cleaner.
- Keep out of reach of children.
We warranty the quality of our product and this data sheet represents test results and practical experience
obtained under controlled conditions. We reserve the right to change data without prior notice.
RECOMMENDED USE
Flash Point
TECHNICAL INFORMATION
White and Light colors.
Matt / Rough
56% 2%
1.0 - 0.6 m2/Lit. (depending on thickness).
1.05 0.05
Touch Dry: 4 - 6 hrs.
Recoat Interval: 12 - 16 hrs.
Temperature, humidity, air movement, film thickness and number of
coats all affect the drying time.
Water base.
Application Methods
Thinning (Max. Vol.)
Thinning / Cleaning of Tools
Film Thickness
APPLICATION DATA
Roller, Spray, long haired brush or knife applicator.
5% depending on the method of application.
Water
(D.F.T.) 600 -1000 microns.
Colors
Finish
Solid by Volume %
Theoretical Spreading Rate
Specific Gravity KG/L
Drying Time
SURFACE PREPARATION
Surface should be thoroughly cleaned, dry and applied as follows:-.
National Acrylic Primer (W.B.)
: 1 coat
OR
National Thermal Insulating Paint (1:1 diluted)
: 1 coat
: 2 coats
National Thermal Insulating Paint
For galvanized surface use National Wash Primer before application.
1/2
HANDLING
SHELF LIFE
SAFETY / HEALTH
NOTE:
We warranty the quality of our product and this data sheet represents test results and practical experience
obtained under controlled conditions. We reserve the right to change data without prior notice.
2/2
RECOMMENDED USE
Colors
Finish
Viscosity
Specific Gravity KG/L
Solid by Weight %
Penetration)
Drying Time
Flash point
Application Methods
Thinning (Max. Vol.)
Thinning / Cleaning of Tools
Guiding Data for Airless Spray
Conv. Spray Requirements
Recommended System
STORAGE
HANDLING
SHELF LIFE
SAFETY / HEALTH
NOTE:
We warranty the quality of our product and this data sheet represents test results and practical experience
obtained under controlled conditions. We reserve the right to change data without prior notice.
RECOMMENDED USE
Colors
Finish
Viscosity
Specific Gravity KG/L
Solid by Weight %
Penetration)
Drying Time
Flash point
Application Methods
Thinning (Max. Vol.)
Thinning / Cleaning of Tools
Guiding Data for Airless Spray
Conv. Spray Requirements
Recommended System
STORAGE
HANDLING
SHELF LIFE
SAFETY / HEALTH
NOTE:
We warranty the quality of our product and this data sheet represents test results and practical experience
obtained under controlled conditions. We reserve the right to change data without prior notice.
RECOMMENDED USE
Colors
Finish
Volume Solids
Specific Gravity KG/L
Theoretical Spreading Rate
Film Thickness
Drying Time @ 30C.
STORAGE
HANDLING
SHELF LIFE
SAFETY / HEALTH
NOTE:
Temperature, humidity, air movement and film thickness all affect the
drying time.
32C.
APPLICATION DATA
Roller or spray.
5% depending on the method of application.
National Acrylic Thinner.
Nozzle Tip: : 0.018" - 0.020"
Nozzle Pressure: 2100 P.S.I.
Automizing Pressure: 50 P.S.I.
Base : Hardener : N.A.
N.A.
National Penetrating Siloxane Primer Sealer: 1 coat.
National Aliphatic Acrylic H.B.
: 2 coats.
MISCELLANEOUS DATA
The product must be stored according to National Regulations. The
product should be kept in cool and well ventilated place, protected from
heat and direct sunlight at temp 5-35C. Containers must be kept tightly
closed.
Handle with care, mix well before use.
18 months.
- Ensure good ventilation during application and drying.
- Avoid contact with skin and eyes. While painting it is advisable to
wear eye protector. In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice. To remove splashes
from skin; use soap and water or a recognized skin cleaner.
- Keep out of reach of children.
We warranty the quality of our product and this data sheet represents test results and practical experience
obtained under controlled conditions. We reserve the right to change data without prior notice.
PROTECT SEAL
DESCRIPTION
RECOMMENDED USE
Colors
Finish
Volume Solids
Specific Gravity KG/L
Theoretical Spreading Rate
Film Thickness
Drying Time @ 30C.
Flash point
Application Methods
Thinning (Max. Vol.)
Thinning / Cleaning of Tools
Guiding Data for Airless Spray
Conv. Spray Requirements
Mixing Ration (Volume)
Pot Life @ 30C.
Recommended System
1/2
PROTECT SEAL
MISCELLANEOUS DATA
STORAGE
HANDLING
SHELF LIFE
SAFETY / HEALTH
NOTE:
We warranty the quality of our product and this data sheet represents test results and practical experience
obtained under controlled conditions. We reserve the right to change data without prior notice.
2/2