Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
TECHNICAL FEATURES
COMPONENT SPECIFICATIONS
ENERGY LABEL
NAME PLATE
FAILURE CODES
AUTO TEST CHART
DETERGENT BOX GROUP WORK PRINCIPLE
CHILD LOCK MANUAL
AUTOTEST MANUAL
Technical Features
Capacity
Colour
: White
Spinning
: 220-240 V
Frequency
: 50 Hz
Ampere
: 10 A
: 2100 W
Component specifications
DOOR LOCK
Technical features :
Lock Time (20 C)
Unlock Time (20 C)
Nominal voltage
Nominal current
2 6
35 75
250 V
16 (4) A
Checking of component :
Check the resistance value on the component with multimeter as shown in Figure2.
Resistance value on the PTC should be 1000 50%.
DRAIN PUMP
Drain pump is both a mechanical and elektrical component
which is used to drain water inside the washing machine. It
has an synchronous motor inside. For better performance
maintanance, pump filter should be cleaned regularly.
Technical features :
Nominal voltage
Nominal current
Nominal power
Frequency
Resistor (coil)
Water flow:
Thermal protector
230 V
0.2 A
30 W
50 Hz
170 (7%)
18 l/min(to 1 m height)
YES
Checking of component :
Check the resistance value on the component with multimeter as shown in Figure 4.
Resistance value should be between 140- 200 Ohm
NTC
Component which sends signals to PCB about the water temperature inside
the tub. The Resistance (Ohm) value of the NTC decreases as the
temperature increases.
Figure 5. NTC
Techinal Feature :
Checking of component :
Check the resistance value on the component with multimeter as shown in Figure 6.
EMI FILTER
EMI Filter Functions:
1. To adjust the frequency changes to the value of 50-60 Hz
which is the nominal frequency for the components.
2. To prevent harmonic frequency feedback sent by motor ,
resistance to the the network.
Technical features :
Rated Voltage
Rated Current
Cx
Cy
L
R
250 V
16 A
0,47 F (20%)
2 x 25 nF (20%)
2 x 1 mH (+%50,-%30)
680 k (10%)
Checking of component :
Check the resistance value on the component with multimeter as shown in Figure 8.
Resistance value on the EMI filter (between L-N polars) should be 680 kohm (10%).
PRESSURE SWITCH
Voltage
Amper
: 250 V
:16 A
Technical features :
The component has three levels. When the component is at reset level, the machine begins to take
water inside. When the component is at set level, the machine stops to take water inside by
communicating with PCB card. The third level, overflow level, is set to prevent taking excessive
water(overflow) into the machine.
The pressure switches that have different water set levels have different water intake values
accordingly.
Checking of component :
1 ) Blow into the pressure switch hose or pressure switch entry. Be sure that you hear the switch click.
2 ) Turn the program adjustment knob rinse mode and let the machine take water in. Be sure that you
hear the switch click or the machine stops to take water inside after a while. (Figure 10.)
RESISTANCE
Technical features :
Kind of heating
Nominal voltage
Nominal power
Resistance
Thermal fuse
Checking of component :
Check the resistance value on the component with multimeter as shown in Figure 12.
Resistance value should be between 25- 30 Ohm.
10
VALVE
Valve is an electrical and mechanical component which is
designed to take water from the network system into the washine
machine. It is operated by PCB card.
Technical features :
Nominal voltage
Nominal power
Frequency
Rated flow:
Operating water pressure
220 240 V
8 VA
50 Hz
6 1/min (15%) (for cold inlet)
5.5 1/min (15%) (for hot inlet)
0.2 10 bar
Checking of component :
Check the resistance value on the component with multimeter as shown in Figure 14.
Valve water flow rate should be between 6 - 8 lt/min.
Each valve bobbin resistance values should be between 3 - 4.5 k .
11
MOTOR
The washing machine has an asynchronous
motor. It is controlled by the PCB.
It is essential to check the motor for correct
diagnosis and quick servicing. In the below picture,
socket points on the motor is shown to measure with
multimeter.
Tacho socket
terminal
Rotor coil
socket
terminal
Stator coil
socket
terminal
Tapped filled
coil socket
terminal
12
Earthing
Tacho and stator (full field-half field) ohm resistance values for the motor types are listed in the below table.
MOTOR
CODE
SUPPLIER
STATOR (FULL
FIELD) (ohm)
TACHO
(ohm)
STATOR (HALF
FIELD) (ohm)
30027193
ANAIMEP
1.87-/+7%
180 -/+10%
20 C
30023397
ANAIMEP
1.75-/+7%
180 -/+10%
20 C
32002064
ANAIMEP
2.01-/+7%
180 -/+7%
20 C
32003425
ANAIMEP
2.01-/+7%
180 -/+7%
20 C
32000536
CESET
1.01 -/+7%
68.7-/+7%
20 C
32000271
CESET
1.40 -/+7%
68.7-/+7%
32000535
CESET
1.24 -/+7%
68.7-/+7%
32000537
CESET
1.34 -/+7%
68.7-/+7%
32002064
WELLING
2.08 -/+7%
66.6 -/+7%
20 C
32003425
WELLING
1.59 -/+7%
66.6 -/+7%
20 C
32004572
ACC
1.20 -/+7%
184 -/+10%
32004968
ATB
1.63-/+7%
90 -/+12%
32004969
ATB
1.57-/+7%
90 -/+12%
32004970
ATB
1.57-/+7%
90 -/+12%
0.56 -/+7%
13
20 C
20 C
0.56 -/+7%
0.60 -/+7%
20 C
20 C
20 C
0.80 -/+7%
TEMPERATURE
20 C
20 C
-W Tf-
-W0 Tf-
14
Connect one of the wires on the power cable with other rotor coil terminal.
-W Tf-
-W0 Tf-
Connect the other wire on the power cable with other stator coil terminal.
-W Tf-
-W0 Tf-
15
ELECTRONIC CARD
Electronic card (PCB) is the control department of the washing machine. PCB gets and
sends signals to electrical components. All the program software is loaded in PCB.
16
ENERGY LABEL
LOGO:XXXXXX
MODEL:XXXXX
ENERGY PERFORMANCE
A
ENERGY CONSUMPTION
5
6
7
7,5
KG
KG
KG
KG
: 0,95 kWh/program
: 1,14 kWh/program
: 1,33 kWh/program
: 1,42 kWh/program
WASHING PERFORMANCE
A
SPINNING PERFORMANCE
600 RPM
800 RPM
1000 RPM
1200 RPM
1400 RPM
1600 RPM
:E
:D
:C
:B
:B
:A
CAPACITY
5 KG
6 KG
7 KG
7,5 KG
WATER CONSUMPTION
5 KG
6 KG
7 KG
7,5 KG
:
:
:
:
43 lt
49 lt
62 lt
63 lt
17
NAME PLATE
0000
18
SERVICE INDEX
NUMBER
Failure Codes
FAILURE CODE 1
19
C- Error flowcharts
20
FAILURE CODE 2
21
C- Error flowcharts
22
FAILURE CODE 3
23
C- Error flowcharts
24
FAILURE CODE 4
25
C- Error flowcharts
26
FAILURE CODE 5
27
C- Error flowcharts
28
FAILURE CODE 6
29
C- Error flowcharts
30
FAILURE CODE 7
31
C- Error flowcharts
32
FAILURE CODE 8
33
C- Error flowcharts
34
FAILURE CODE 9
35
C- Error flowcharts
36
37
SOFTENER
VALVE 1
PREWASH
VALVE 2
38
39
Wash, rinse and spin LEDs will flash for 2 seconds, if any button is pressed on the
control panel.
Press the first and second function button for 3-4 seconds to inactivate child lock.
40
41
AUTOTEST MANUAL
1) Press the 1st Function button when the Program knob is at the STOP position.
2) While pressing 1st Fuction button. Change the position of the knob to 1.
42