Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Styrolution PS HIPS
Material number PS0002
1 of 6
Styrolution PS HIPS
This safety data sheet pertains to the following products:
Styrolution PS 2710 GR2
Styrolution PS 456EB GR2
Styrolution PS 476L GR2
Styrolution PS 476L GR21
Styrolution PS 495F GR2
Styrolution PS 495F GR21
Styrolution PS 576H GR21
Relevant identified uses of the substance or mixture and uses advised against
General use:
2. Hazards identification
Classification of the substance or mixture
GHS classification
This substance is classified as not hazardous.
Label elements
Hazard statements:
not applicable
Safety precautions:
not applicable
Other hazards
Dust: Can cause skin, eye and respiratory tract irritation.
fine dust: explosive
The melted product can cause severe burns.
polymer
(C8H8,C4H6)x
styrene-butadiene-copolymer, HIPS
CAS-Number:
RTECS-Number:
2 of 6
9003-55-8
WL6478000
After swallowing:
Provide fresh air. Put victim at rest and keep warm. seek medical attention
The melted product can cause severe burns.
Do not remove the product from the skin without medical assistance.
After contact with molten product, cool skin area rapidly with cold water. Consult physician.
Immediately flush eyes with plenty of flowing water for 10 to 15 minutes holding eyelids apart.
Consult an eye specialist in the event of irritation.
Remove contact lenses, if present and easy to do. Continue rinsing.
Do not induce vomiting. Rinse mouth with water.
Drink one or two glasses of water.
Never give an unconscious person anything through the mouth.
5. Firefighting measures
Extinguishing media
Suitable extinguishing media:
Additional information:
Environmental precautions
Do not allow to penetrate into soil, waterbodies or drains.
Additional information:
Page:
3 of 6
Dust forms explosive mixtures with air. Take precautionary measures against static discharge.
Keep away from sources of ignition. Use grounding equipment. Use explosion-proof equipment
and non-sparking tools/utensils.
Storage
Requirements for storerooms and containers:
Further details:
CAS No.
Designation
Type
Styrene
106-99-0
1,3-Butadiene
Limit value
10 mg/m
Dust limit value, indicativ; inhalable fraction
3 mg/m
Dust limit value, indicativ; respirable fraction
170 mg/m; 40 ppm
85 mg/m; 20 ppm
4,4 mg/m; 2 ppm (A2)
Exposure controls
Provide good ventilation and/or an exhaust system in the work area.
See also information in chapter 7, section storage.
4 of 6
Appearance:
Odour:
Flash point/flash point range:
Flammability:
Density:
Water solubility:
Autoflammability:
> 280 C
Not highly flammable.
at 20 C approx. 1030 kg/m (ISO 1183)
insoluble
not self-igniting
Additional information
approx. > 400 C
approx. 600 g/cm
Ignition temperature:
Bulk density:
No data available
Chemical stability:
Incompatible materials:
In case of fire may be liberated: smoke, Styrene-Monomer, butadiene, aldehydes and acids
(organic), carbon monoxide and carbon dioxide (CO2).
LD50 oral:
> 2.000 mg/kg
LD50 dermal: > 2.000 mg/kg
Toxicological effects:
Other information:
Styrene:
1,3-Butadiene:
5 of 6
Acute toxicity (oral): Based on available data, the classification criteria are not met.
Acute toxicity (dermal): Based on available data, the classification criteria are not met.
Acute toxicity (inhalative): Lack of data.
Skin corrosion/irritation: Lack of data.
Eye damage/irritation: Lack of data.
Sensitisation to the respiratory tract: Lack of data.
Skin sensitisation: Based on available data, the classification criteria are not met. Not
sensitising
Germ cell mutagenicity/Genotoxicity: Lack of data.
Carcinogenicity: Lack of data. Carcinogen Status: IARC Rating: 3
Reproductive toxicity: Lack of data.
Effects on or via lactation: Lack of data.
Specific target organ toxicity (single exposure): Lack of data.
Specific target organ toxicity (repeated exposure): Lack of data.
Aspiration hazard: Lack of data.
When handled appropiately, even after long years of experience with this product, no adverse
health effects are known.
Harmful if inhaled. Causes damage to organs through prolonged or repeated exposure.
lung damages
May be fatal if swallowed and enters airways.
Causes serious eye irritation. Causes skin irritation.
May cause cancer. May cause genetic defects.
Symptoms
Dust: Skin irritation, eye irritations and redness
The melted product can cause severe burns.
Thermal treatment, Processing:
Irritating to eyes, respiratory system and skin.
Mobility in soil
Product is not soluble in water.
Substance is heavier than water and sinks.
mobility in soil: low
6 of 6
Contaminated packaging
Recommendation:
Dispose of waste according to applicable legislation.
Further information
No dangerous good in sense of these transport regulations.
R phrase(s):
S phrase(s):
not applicable
not applicable
not applicable
The information in this data sheet has been established to our best knowledge and was up-to-date at time of revision.
It does not represent a guarantee for the properties of the product described in terms of the legal warranty regulations.