Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
The following assembly and installation instructions describe the assembly of an antenna with an offset fine mount AFM, and installation onto a tower and/or
an antenna pole with pipe diameter from 42mm up to 115mm.
1 ft. antenna
All instructions are intended for qualified and skilled personnel only. Following these instructions will help you avoid improper installation. Please read carefully
all notes and pictures prior to assembling.
This package contents all parts belonging to the antenna: parabolic dish, feeder, radome, offset mount AFM, and all fasteners.
Standard package does not contain installation tools.
!
Required Tools
Hexagon socket T-shape key
6 mm
Important note
We recommend that installed antenna shall be inspected once per year to verify safety and
condition. It is also a good idea to compare RSSI results over time to make sure the antenna is
loose or there is movement of the mounting structure.
It is important that mounting structures, towers, pipes, tripods etc. be fixed so that there is no
excess movement. Radial, twisting, of the structure is much worse than axial movement, but
no movement is best.
ALCOMA disclaims any responsibility for improper or unsafe installation. Please follow
recommended safety procedures for assembling the antenna (page 3) and the mount (page 4)
in dangerous locations, height, (on Towers, Roofs, etc.) Please follow all local safety codes for
mechanical and electrical installation. National and local codes should be followed. Alcoma
disclaims any responsibility for improper installation by untrained personnel.
2 ft. antenna
Information
For technical specifications of the antenna such as: gain, frequency band, radiation pattern,
main dimensions, forces, etc., please see datasheet. (Not printed on these pages).
Combination Spanner / Wrench
17 mm
13 mm
Screwdriver
Pozidriv PZ 2
Legend
Important note
Information / Advise
6 mm
F3
Fig.: 4
Next step
Tool size
Screw or Nut identifier
www.alcoma.com ALCOMA a.s. 106 00, Prague 10, Vinova 11 - Czech Republic
Done
REV.: 140319
www.alcoma.com ALCOMA a.s. 106 00, Prague 10, Vinova 11 - Czech Republic
assembly
4pcs
Tools
Item
C2
A2
A 1ft.
A 2ft.
A1
A2
A3
A4
A5
B - FEEDER
Item
B 1ft.
B 2ft.
B1
Combination Spanner
17 mm
A
A3
5
A2
2pcs
1
(1)
4
C - RADOME assembly
C 1ft.
C 2ft.
C1
C2
A3
13 mm
A4
1
(1)
1
2
1
1
1
Qty.
Name
Item
C1
4pcs
Qty.
Name
B1
Qty.
Name
1
(1)
4
4
4pcs
Fig. 1, 2
Fig. 3
Screwdriver
B 1 C1
according to L/R
an
te
installation
ing
ole
ap
ac
pl
nn
R a do m e a n d S h a
ck
le
Pozidriv PZ 2
Assembling instructions
1. See Fig. 1 for Radome and Shackle placing prior to assembling.
(All pictures are being shown typically with Left side offset installation at the antenna pole.)
2. Feeder is a precision made microwave part of the antenna. Handle with care!
3. Read all important recommendations related to Radome s Screw Rivets before the Radome will be
attached onto the
antenna dish.
4. If the reflection absorber has been applied inside the Radome please do not touch it otherwise it will
make your hands dirty.
Fig. 1
5. Make sure that all fasteners are properly tightened before the antenna will be mounted!
PZ 2
Only!
Fig. 2
Insert Rivets
www.alcoma.com ALCOMA a.s. 106 00, Prague 10, Vinova 11 - Czech Republic
Lock Rivet
Unl
ock Riv t (loosen)
e
Fig. 2
Fig. 4
REV.: 140319
assembly
D - CLAMP assembly
Tools
Item
F3
D1
D2
D3
D4
D5
D6
Qty.
Name
1
2
4
4
4
8
E - AZIMUTH assembly
Item
Combination Spanner
17 mm
E
E1
E2
E3
4pcs
Fig. 5
4pcs
D4
D2
2pcs
4pcs
D6
8pcs
Qty.
Name
1
2
2
2
F - ELEVATION assembly
F
F1
F2
F3
F4
F5
F6
D5
Fig. 7
Item
D3
D1
F4
Qty.
Name
Main Elevation assembly
Hex. Head Bolt M1075 DIN 931 / A2-70
Hex. Head Bolt M1060 DIN 931 / A2-70
Countersunk Head Screw DIN 7991 M1075 / A2-70
Washer M10 DIN 9021 / A2
Washer M10 DIN 125A / A2
Spring Washer M10 DIN 127B / A2
1
1
1
1
1
1
2
F1
F2
F6
E2
2pcs
2pcs
F5
E3
2pcs
E1
2pcs
Fig. 8
n4 2 - 7
2 mm
n 65
- 115
F3
mm
Fig. 5
Mount assembly is identical for Left and/or Right side antenna offset installation
Fig. 6
www.alcoma.com ALCOMA a.s. 106 00, Prague 10, Vinova 11 - Czech Republic
Fig. 9
REV.: 140319
Tool
Hexagon socket T-shape key
Tool
Combination Spanner
6 mm
Installation
17 mm
Fig. 13
ning sequen
hte
ce
g
i
T
3.5 kg
Fig. 13
st. TOP
(only mount)
Fig. 10
Fig. 11
nd.
rd.
WARNING
up
Tighten
3 180
Tighten
8 0 + 90
1
2
to
85
Tighten
2 180
11
www.alcoma.com ALCOMA a.s. 106 00, Prague 10, Vinova 11 - Czech Republic
Fig. 14
REV.: 140319
ELEVATION
Tools
Advice
Combination Spanner
17 mm
LOCK ADJUSTING
UNLOCK ADJUSTING
Fine adjustment
ELEVATION `30
Important note
Tighten
35 N m
Lock AZIMUTH
Tighten
3 5 Nm
Fig. 18
AZIMUTH
Loosen
180 (1/2)
Lock AZIMUTH
35 Nm (25.8 lb ft)
Fine adjustment
Lock ELEVATION
AZIMUTH `15
35 Nm (25.8 lb ft)
Fig. 16
Fig. 17
www.alcoma.com ALCOMA a.s. 106 00, Prague 10, Vinova 11 - Czech Republic
Fig. 19
REV.: 140319